TY  - CHAP
A1  - Weber, S.
A1  - Terstegge, Andreas
A1  - Engels, R.
A1  - Herzog, H.
A1  - Reinartz, R.
A1  - Reinhart, P.
A1  - Rongen, F.
A1  - Müller-Gärtner, H. W.
A1  - Halling, H.
T1  - The KFA TierPET: performance characteristics and measurements
T2  - Conference record / 1996 IEEE Nuclear Science Symposium [and Medical Imaging], November 2 - 9, 1996, Anaheim, California ; vol. 2
Y1  - 1996
SN  - 0-7803-3534-1
SN  - 1082-3654
SP  - 1117
EP  - 1119
PB  - IEEE
CY  - Piscataway, NJ
ER  - 
TY  - JOUR
A1  - Heinrich, U.
A1  - Blum, A.
A1  - Bussmann, N.
A1  - Engels, R.
A1  - Kemmerling, G.
A1  - Weber, S.
A1  - Ziemons, Karl
T1  - Statistical studies on the light output and energy resolution of small LSO single crystals with different surface treatments combined with various reflector materials
JF  - Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
N2  - The optimization of light output and energy resolution of scintillators is of special interest for the development of high resolution and high sensitivity PET. The aim of this work is to obtain statistically reliable results concerning optimal surface treatment of scintillation crystals and the selection of reflector material. For this purpose, raw, mechanically polished and etched LSO crystals (size 2×2×10 mm3) were combined with various reflector materials (Teflon tape, Teflon matrix, BaSO4) and exposed to a 22Na source. In order to ensure the statistical reliability of the results, groups of 10 LSO crystals each were measured for all combinations of surface treatment and reflector material. Using no reflector material the light output increased up to 551±35% by mechanical polishing the surface compared to 100±5% for raw crystals. Etching the surface increased the light output to 441±29%. The untreated crystals had an energy resolution of 24.6±4.0%. By mechanical polishing the surface it was possible to achieve an energy resolution of 13.2±0.8%, by etching of 14.8±0.7%. In combination with BaSO4 as reflector material the maximum increase of light output has been established to 932±57% for mechanically polished and 895±61% for etched crystals. The combination with BaSO4 also caused the best improvement of the energy resolution up to 11.6±0.2% for mechanically polished and 12.2±0.3% for etched crystals. Relating to the light output there was no significant statistical difference between the two surface treatments in combination with BaSO4. In contrast to this, the statistical results of the energy resolution have shown the combination of mechanical polishing and BaSO4 as the optimum.
Y1  - 2002
SN  - 0168-9002
N1  - Proceedings of the 6th International Conference on Inorganic Scin tillators and their Use in Scientific and Industrial Applications
VL  - 486
IS  - 1-2
SP  - 60
EP  - 66
ER  - 
TY  - JOUR
A1  - Bussmann, N.
A1  - Engels, R.
A1  - Fuss, L.
A1  - Kemmerling, G.
A1  - Reinartz, R.
A1  - Langen, K.-J.
A1  - Schelten, J.
A1  - Ziemons, Karl
T1  - Performance measurement of a new high resolution detector system for I-131 thyroid studies
JF  - 2000 IEEE Nuclear Science Symposium Conference Record, Vol. 3
N2  - A 2-dimensional detector system for high resolution thyroid I-131 scintigraphy was developed. It has a sensitive area of 4 cm×4 cm and consists of a lead-collimator and an array of 10×10 EGO crystals combined with a position sensitive photomultiplier. The spatial resolution and the sensitivity of the detector has been measured and compared to two commercially available gamma-cameras. Furthermore first patient measurements have been carried out
Y1  - 2000
SN  - 1082-3654
SP  - 22/35
EP  - 22/37
ER  -