TY - BOOK A1 - Gebhardt, Andreas T1 - Rapid prototyping : Werkzeug für die schnelle Produktentstehung. - 2., völlig überarb. Aufl. Y1 - 2000 SN - 3-446-21242-6 PB - Hanser CY - München [u.a.] ER - TY - BOOK A1 - Gebhardt, Andreas T1 - Rapid Prototyping Y1 - 2003 SN - 3-446-21259-0 PB - Hanser CY - Munich [u.a.] ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Rapid Prototyping JF - Landolt-Börnstein - Group VIII Advanced Materials and Technologies‡Vol. 1 Laser Physics and Applications‡Subvol. C Laser Applications / authors: Bäuerle, D. ... Y1 - 2004 SN - 3-540-00105-0 SP - 105 EP - 123 PB - Heidelberg CY - Springer ER - TY - JOUR A1 - Franzen, Julius A1 - Pinders, Erik A1 - Pfaff, Raphael A1 - Enning, Manfred T1 - RailCrowd’s virtual fleets: Make most of your asset data JF - Deine Bahn N2 - For smaller railway operators or those with a diverse fleet, it can be difficult to collect sufficient data to improve maintenance programs. At the same time, new rules such as entity in charge of maintenance – ECM – regulations impose an additional workload by requiring a dedicated maintenance management system and specific reports. The RailCrowd platform sets out to facilitate compliance with ECM and similar regulations while at the same time pooling anonymised fleet data across operators to form virtual fleets, providing greater data insights. Y1 - 2018 SN - 0948-7263 IS - 9 SP - 11 EP - 13 PB - Bahn-Fachverlag CY - Berlin ER - TY - JOUR A1 - Kunkel, Maximilian Hugo A1 - Gebhardt, Andreas A1 - Mpofu, Khumbulani A1 - Kallweit, Stephan T1 - Quality assurance in metal powder bed fusion via deep-learning-based image classification JF - Rapid Prototyping Journal Y1 - 2019 U6 - http://dx.doi.org/10.1108/RPJ-03-2019-0066 SN - 1355-2546 VL - 26 IS - 2 SP - 259 EP - 266 ER - TY - JOUR A1 - Raffeis, Iris A1 - Adjei-Kyeremeh, Frank A1 - Vroomen, Uwe A1 - Westhoff, Elmar A1 - Bremen, Sebastian A1 - Hohoi, Alexandru A1 - Bührig-Polaczek, Andreas T1 - Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties JF - Applied Sciences N2 - As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni–Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s–1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20% to 31% (V), as well as from 16% to 25% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced. Y1 - 2020 U6 - http://dx.doi.org/10.3390/app10103401 SN - 2076-3417 N1 - Special Issue Materials Development by Additive Manufacturing Techniques VL - 10 IS - Art. 3401 SP - 1 EP - 15 PB - MDPI CY - Basel ER - TY - CHAP A1 - Schmidt, Thomas A1 - Kasch, Susanne A1 - Eichler, Fabian A1 - Thurn, Laura T1 - Process strategies on laser-based melting of glass powder T2 - Lasers in Manufacturing Conference 2021 N2 - This paper presents the laser-based powder bed fusion (L-PBF) using various glass powders (borosilicate and quartz glass). Compared to metals, these require adapted process strategies. First, the glass powders were characterized with regard to their material properties and their processability in the powder bed. This was followed by investigations of the melting behavior of the glass powders with different laser wavelengths (10.6 µm, 1070 nm). In particular, the experimental setup of a CO2 laser was adapted for the processing of glass powder. An experimental setup with integrated coaxial temperature measurement/control and an inductively heatable build platform was created. This allowed the L-PBF process to be carried out at the transformation temperature of the glasses. Furthermore, the component’s material quality was analyzed on three-dimensional test specimen with regard to porosity, roughness, density and geometrical accuracy in order to evaluate the developed L-PBF parameters and to open up possible applications. KW - 3D-printing KW - glass KW - additive manufactureing KW - laser based powder fusion Y1 - 2021 ER - TY - CHAP A1 - Rieper, Harald A1 - Gebhardt, Andreas A1 - Stucker, Brent T1 - Process parameters for Selective Laser Melting of AgCu7 T2 - DDMC, Fraunhofer Direct Digital Manufacturing Conference, 3 Y1 - 2016 SN - 978-3-8396-1001-5 N1 - DDMC, 2016, Fraunhofer Direct Digital Manufacturing Conference, 3rd, Berlin, DE, 2016-03-16 - 2016-03-17 SP - 171 EP - 176 PB - Fraunhofer-Verlag CY - Stuttgart ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Process Parameters Development of Selective Laser Melting of Lunar Regolith for On-Site Manufacturing Applications JF - International Journal of Applied Ceramic Technology Y1 - 2015 SN - 1744-7402 U6 - http://dx.doi.org/10.1111/ijac.12326 VL - 12 IS - 1 SP - 46 EP - 52 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Anik, Sabri A1 - Frohberg, Martin G. A1 - Kapoor, Madan Lal T1 - Prediction of thermodynamic properties of oxygen in binary metallic solvents JF - Zeitschrift für Metallkunde Y1 - 1983 SN - 0044-3093 VL - 74 IS - 6 SP - 372 EP - 375 ER -