TY - CHAP A1 - Finger, Felix A1 - de Vries, Reynard A1 - Vos, Roelof A1 - Braun, Carsten A1 - Bil, Cees T1 - A comparison of hybrid-electric aircraft sizing methods T2 - AIAA Scitech 2020 Forum N2 - The number of case studies focusing on hybrid-electric aircraft is steadily increasing, since these configurations are thought to lead to lower operating costs and environmental impact than traditional aircraft. However, due to the lack of reference data of actual hybrid-electric aircraft, in most cases, the design tools and results are difficult to validate. In this paper, two independently developed approaches for hybrid-electric conceptual aircraft design are compared. An existing 19-seat commuter aircraft is selected as the conventional baseline, and both design tools are used to size that aircraft. The aircraft is then re-sized under consideration of hybrid-electric propulsion technology. This is performed for parallel, serial, and fully-electric powertrain architectures. Finally, sensitivity studies are conducted to assess the validity of the basic assumptions and approaches regarding the design of hybrid-electric aircraft. Both methods are found to predict the maximum take-off mass (MTOM) of the reference aircraft with less than 4% error. The MTOM and payload-range energy efficiency of various (hybrid-) electric configurations are predicted with a maximum difference of approximately 2% and 5%, respectively. The results of this study confirm a correct formulation and implementation of the two design methods, and the data obtained can be used by researchers to benchmark and validate their design tools. Y1 - 2020 U6 - https://doi.org/10.2514/6.2020-1006 N1 - AIAA Scitech 2020 Forum, Driving aerospace solutions for global challenges, Orlando, 06. - 10. January 2020 ER - TY - CHAP A1 - Ögun, Celal Mohan A1 - Kling, Rainer A1 - Heuermann, Holger A1 - Gräser, Ulrich A1 - Schopp, Christoph T1 - Elektrodenlose quecksilberfreie Niederdrucklampen betrieben mit Mikrowellen T2 - Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband Y1 - 2014 PB - Nederlandse Stichting voor Verlichtingskunde CY - Ede ER - TY - CHAP A1 - Anthrakidis, Anette A1 - Herrmann, Ulf A1 - Schorn, Christian A1 - Schwarzer, Klemens A1 - Wedding, Philipp T1 - Weiterentwicklung und Erprobung eines neuartigen Verfahrens zur Bestimmung der Effizienz von konzentrierenden solarthermischen Kollektoren T2 - 25. OTTI Symposium Thermische Solarenergie Y1 - 2015 ER - TY - CHAP A1 - Welden, Melanie A1 - Severins, Robin A1 - Poghossian, Arshak A1 - Wege, Christina A1 - Siegert, Petra A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Studying the immobilization of acetoin reductase with Tobacco mosaic virus particles on capacitive field-effect sensors T2 - 2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN) N2 - A capacitive electrolyte-insulator-semiconductor (EISCAP) biosensor modified with Tobacco mosaic virus (TMV) particles for the detection of acetoin is presented. The enzyme acetoin reductase (AR) was immobilized on the surface of the EISCAP using TMV particles as nanoscaffolds. The study focused on the optimization of the TMV-assisted AR immobilization on the Ta 2 O 5 -gate EISCAP surface. The TMV-assisted acetoin EISCAPs were electrochemically characterized by means of leakage-current, capacitance-voltage, and constant-capacitance measurements. The TMV-modified transducer surface was studied via scanning electron microscopy. KW - Tobacco mosaic virus KW - acetoin KW - capacitive field-effect biosensor KW - enzyme immobilization Y1 - 2022 SN - 978-1-6654-5860-3 (Online) SN - 978-1-6654-5861-0 (Print) U6 - https://doi.org/10.1109/ISOEN54820.2022.9789657 N1 - IEEE International Symposium on Olfaction and Electronic Nose (ISOEN), 29 May 2022 - 01 June 2022, Aveiro, Portugal. PB - IEEE ER - TY - CHAP A1 - Poghossian, Arshak A1 - Bronder, Thomas A1 - Scheja, S. A1 - Wu, Chunsheng A1 - Metzger-Boddien, C. A1 - Keusgen, M. A1 - Schöning, Michael Josef T1 - Label-free Electrostatic Detection of DNA Amplification by PCR Using Capacitive Field-effect Devices T2 - Procedia Engineering N2 - A capacitive field-effect EIS (electrolyte-insulator-semiconductor) sensor modified with a positively charged weak polyelectrolyte of poly(allylamine hydrochloride) (PAH)/single-stranded probe DNA (ssDNA) bilayer has been used for a label-free electrostatic detection of pathogen-specific DNA amplification via polymerase chain reaction (PCR). The sensor is able to distinguish between positive and negative PCR solutions, to detect the existence of target DNA amplicons in PCR samples and thus, can be used as tool for a quick verification of DNA amplification and the successful PCR process. Y1 - 2016 U6 - https://doi.org/10.1016/j.proeng.2016.11.512 SN - 1877-7058 N1 - Proceedings of the 30th anniversary Eurosensors Conference – Eurosensors 2016, 4-7. Sepember 2016, Budapest, Hungary VL - Vol. 168 SP - 514 EP - 517 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Thenent, N. E. A1 - Dahmann, Peter T1 - Increasing aircraft design flexibility ‐ The development of a hydrostatic transmission for gliders with self‐launching capability T2 - Deutscher Luft- und Raumfahrtkongress 2011 : Bremen, 27. bis 29. September 2011 ; Tagungsband Y1 - 2011 SN - 978-3-9321-8274-7 SP - 865 EP - 883 PB - Dt. Gesellschaft für Luft- und Raumfahrt CY - Bonn ER - TY - CHAP A1 - Staat, Manfred A1 - Szelinski, E. A1 - Heitzer, Michael T1 - Kollapsanalyse von längsfehlerbehafteten Rohren und Behältern T1 - Collapse analysis of longitudinally flawed pipes and vessels N2 - Es werden verbesserte Kollapsanalysen von dickwandigen, mit axialen Oberflächenfehlern behafteten Rohren und Behältern vorgeschlagen. KW - Druckbehälter KW - Stahl KW - Druckbelastung KW - Druckbeanspruchung KW - Rohr KW - Rohrbruch KW - Fehlerstellen KW - pipes KW - vessels KW - load limit KW - burst tests KW - burst pressure KW - flaw Y1 - 2001 ER - TY - CHAP A1 - Leicht-Scholten, Carmen A1 - Steuer-Dankert, Linda A1 - Bouffier, Anna T1 - Facing Future Challenges: Building Engineers for Tomorrow T2 - Conference proceedings : new perspectives in science education : 5th Conference edition, Florence, Italy, 17-18 March 2016 N2 - Future engineers are increasingly confronted with the so-called Megatrends which are the big social challenges society has to cope with. These Megatrends, such as “Silver Society”, “Globalization”, “Mobility” and “Female Shift” require an application-oriented perspective on Diversity especially in the engineering field. Therefore, it is necessary to enable future engineers not only to look at the technical perspectives of a problem, but also to be able to see the related questions within societies they are developing their artefacts for. The aim of teaching engineering should be to prepare engineers for these requirements and to draw attention to the diverse needs in a globalized world. Bringing together technical knowledge and social competences which go beyond a mere training of the so-called “soft skills”, is a new approach followed at RWTH Aachen University, one of the leading technical universities in Germany. RWTH Aachen University has established the bridging professorship “Gender and Diversity in Engineering” (GDI) which educates engineers with an interdisciplinary approach to expand engineering limits. In the frame of a sustainable teaching concept the research group under the leadership of Prof. Carmen Leicht-Scholten has developed an approach which imparts a supplication-specific Gender and Diversity expertise to engineers. In workshops students gain theoretical knowledge about Gender and Diversity and learn how to transfer their knowledge in their special field of study and later work. To substantiate this, the course participants have to solve case studies from real life. The cases which are developed in collaboration with non-profit organizations and enterprises from economy rise the students to challenges which are inspired by professional life. Evaluation shows the success of this approach as well as an increasing demand for such teaching formats. KW - Diversity KW - Engineering Education KW - Gender KW - Higher Education Y1 - 2016 SN - 978-886292-705-5 SP - 32 EP - 37 ER - TY - CHAP A1 - Finger, Felix A1 - Götten, Falk A1 - Braun, Carsten T1 - Initial Sizing for a Family of Hybrid-Electric VTOL General Aviation Aircraft T2 - 67. Deutscher Luft- und Raumfahrtkongress 2018 Y1 - 2018 ER - TY - CHAP A1 - Ritz, Thomas ED - Zabel, Armin T1 - Produktion von kundenindividuellen Informationsdienstleistungen T2 - Workshop Internetbasierte Vertriebsunterstützung in der Praxis : 26. April 2001, Institutszentrum Stuttgart der Fraunhofer-Gesellschaft (IZS) / Fraunhofer Institut Arbeitswirtschaft und Organisation Y1 - 2001 N1 - Bei dem Beitrag im Tagungsband handelt es sich um einen Ausdruck von PowerPoint-Folien. PB - Fraunhofer IAO CY - Stuttgart ER - TY - CHAP A1 - Jung, Alexander A1 - Staat, Manfred A1 - Müller, Wolfram ED - Onate, E. T1 - Optimization of the flight style in ski jumping T2 - 11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20 - 25, 2014, Barcelona Y1 - 2014 N1 - Das Paper wurde nach der Konferenz überarbeitet. SP - 799 EP - 810 ER - TY - CHAP A1 - Digel, Ilya A1 - Dachwald, Bernd A1 - Artmann, Gerhard A1 - Linder, Peter A1 - Funke, O. T1 - A concept of a probe for particle analysis and life detection in icy environments N2 - A melting probe equipped with autofluorescence-based detection system combined with a light scattering unit, and, optionally, with a microarray chip would be ideally suited to probe icy environments like Europa’s ice layer as well as the polar ice layers of Earth and Mars for recent and extinct live. KW - Sonde KW - Eisschicht KW - Autofluoreszenzverfahren KW - Lichtstreuungsbasierte Instrumente KW - autofluorescence-based detection system KW - light scattering analysis Y1 - 2009 ER - TY - CHAP A1 - Alexopoulos, Spiros A1 - Hoffschmidt, Bernhard A1 - Rau, Christoph A1 - Schwarzbözl, Peter T1 - Simulation results for a hybridization concept of a small solar tower power plant T2 - SolarPACES 2009 : electricity, fuels and clean water powered by the sun ; 15 - 18 September 2009, Berlin, Germany ; the 15th SolarPACES conference ; proceedings Y1 - 2009 SN - 9783000287558 PB - Deutsches Zentrum f. Luft- u. Raumfahrt CY - Stuttgart ER - TY - CHAP A1 - Tran, Thanh Ngoc A1 - Staat, Manfred ED - Eberhardsteiner, J. T1 - A primal-dual shakedown analysis of 3D structures using the face-based smoothed finite element method T2 - Proceedings European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012) Y1 - 2012 N1 - 6th European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012) Vienna, Austria, September 10-14, 2012 ER - TY - CHAP A1 - Schulte, Maximilian A1 - Eggert, Mathias T1 - Predicting hourly bitcoin prices based on long short-term memory neural networks T2 - Proceedings of the International Conference on Wirtschaftsinformatik (WI) 2021 N2 - Bitcoin is a cryptocurrency and is considered a high-risk asset class whose price changes are difficult to predict. Current research focusses on daily price movements with a limited number of predictors. The paper at hand aims at identifying measurable indicators for Bitcoin price movements and the development of a suitable forecasting model for hourly changes. The paper provides three research contributions. First, a set of significant indicators for predicting the Bitcoin price is identified. Second, the results of a trained Long Short-term Memory (LSTM) neural network that predicts price changes on an hourly basis is presented and compared with other algorithms. Third, the results foster discussions of the applicability of neural nets for stock price predictions. In total, 47 input features for a period of over 10 months could be retrieved to train a neural net that predicts the Bitcoin price movements with an error rate of 3.52 %. Y1 - 2021 N1 - 16th International Conference on Wirtschaftsinformatik, March 2021, Essen, Germany ER - TY - CHAP A1 - Ferrein, Alexander A1 - Schiffer, Stefan A1 - Kallweit, Stephan T1 - The ROSIN Education Concept - Fostering ROS Industrial-Related Robotics Education in Europe T2 - ROBOT 2017: Third Iberian Robotics Conference Y1 - 2018 SN - 978-3-319-70836-2 U6 - https://doi.org/10.1007/978-3-319-70836-2_31 N1 - Advances in Intelligent Systems and Computing, vol 694; (AISC, volume 694) SP - 370 EP - 381 PB - Springer CY - Cham ER - TY - CHAP A1 - Frotscher, Ralf A1 - Raatschen, Hans-Jürgen A1 - Staat, Manfred ED - Holzapfel, Gerhard A. T1 - Effectiveness of the edge-based smoothed finite element method applied to soft biological tissues T2 - ESMC-2012 - 8th European Solid Mechanics Conference, Graz, Austria, July 9-13, 2012 Y1 - 2012 SN - 978-3-85125-223-1 PB - Verlag d. Technischen Universität Graz CY - Graz ER - TY - CHAP A1 - Reke, Michael A1 - Peter, Daniel A1 - Schulte-Tigges, Joschua A1 - Schiffer, Stefan A1 - Ferrein, Alexander A1 - Walter, Thomas A1 - Matheis, Dominik T1 - A Self-Driving Car Architecture in ROS2 T2 - 2020 International SAUPEC/RobMech/PRASA Conference, Cape Town, South Africa N2 - In this paper we report on an architecture for a self-driving car that is based on ROS2. Self-driving cars have to take decisions based on their sensory input in real-time, providing high reliability with a strong demand in functional safety. In principle, self-driving cars are robots. However, typical robot software, in general, and the previous version of the Robot Operating System (ROS), in particular, does not always meet these requirements. With the successor ROS2 the situation has changed and it might be considered as a solution for automated and autonomous driving. Existing robotic software based on ROS was not ready for safety critical applications like self-driving cars. We propose an architecture for using ROS2 for a self-driving car that enables safe and reliable real-time behaviour, but keeping the advantages of ROS such as a distributed architecture and standardised message types. First experiments with an automated real passenger car at lower and higher speed-levels show that our approach seems feasible for autonomous driving under the necessary real-time conditions. Y1 - 2020 SN - 978-1-7281-4162-6 U6 - https://doi.org/10.1109/SAUPEC/RobMech/PRASA48453.2020.9041020 N1 - 2020 International SAUPEC/RobMech/PRASA Conference, 29-31 Jan. 2020, Cape Town, South Africa SP - 1 EP - 6 PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Tran, Ngoc Trinh A1 - Tran, Thanh Ngoc A1 - Matthies, Hermann G. A1 - Stavroulakis, Georgios Eleftherios A1 - Staat, Manfred T1 - FEM Shakedown of uncertain structures by chance constrained programming T2 - PAMM Proceedings in Applied Mathematics and Mechanics Y1 - 2016 U6 - https://doi.org/10.1002/pamm.201610346 SN - 1617-7061 N1 - Special Issue: Joint 87th Annual Meeting of the International Association of Applied Mathematics and Mechanics (GAMM) and Deutsche Mathematiker-Vereinigung VL - 16 IS - 1 SP - 715 EP - 716 ER - TY - CHAP A1 - Artmann, Gerhard A1 - Digel, Ilya A1 - Linder, Peter A1 - Temiz Artmann, Aysegül T1 - Biophysical and Engineering Contributions to Plant Research N2 - Tests with palm tree leaves have just started yet and scan data are in the process to be analyzed. The final goal of future project for palm tree gender and species recognition will be to develop optical scanning technology to be applied to date palm tree leaves for in–situ screening purposes. Depending on the software used and the particular requirements of the users the technology potentially shall be able to identify palm tree diseases, palm tree gender, and species of young date palm trees by scanning leaves. KW - Pflanzenphysiologie KW - Dattel KW - Pflanzenscanner KW - plant scanner KW - date palm tree Y1 - 2011 ER - TY - CHAP A1 - Molinnus, Denise A1 - Hardt, Gabriel A1 - Käver, Larissa A1 - Willenberg, Holger S. A1 - Poghossian, Arshak A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Detection of Adrenaline Based on Bioelectrocatalytical System to Support Tumor Diagnostic Technology T2 - MDPI Proceedings Y1 - 2017 U6 - https://doi.org/10.3390/proceedings1040506 ER - TY - CHAP A1 - Staat, Manfred A1 - Duong, Minh Tuan T1 - Smoothed Finite Element Methods for Nonlinear Solid Mechanics Problems: 2D and 3D Case Studies T2 - Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2 N2 - The Smoothed Finite Element Method (SFEM) is presented as an edge-based and a facebased techniques for 2D and 3D boundary value problems, respectively. SFEMs avoid shortcomings of the standard Finite Element Method (FEM) with lower order elements such as overly stiff behavior, poor stress solution, and locking effects. Based on the idea of averaging spatially the standard strain field of the FEM over so-called smoothing domains SFEM calculates the stiffness matrix for the same number of degrees of freedom (DOFs) as those of the FEM. However, the SFEMs significantly improve accuracy and convergence even for distorted meshes and/or nearly incompressible materials. Numerical results of the SFEMs for a cardiac tissue membrane (thin plate inflation) and an artery (tension of 3D tube) show clearly their advantageous properties in improving accuracy particularly for the distorted meshes and avoiding shear locking effects. Y1 - 2016 SP - 440 EP - 445 ER - TY - CHAP A1 - Platen, J. A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - Präparation von selbstjustierenden Nanostrukturen mittels Schichtausdehnungstechnik T2 - Sensoren und Mess-Systeme 2006 : Vorträge der 13. ITG/GMA-Fachtagung vom 13. bis 14.3.2006 in Freiburg/Breisgau Y1 - 2006 SN - 3-8007-2939-3 SP - 277 EP - 280 PB - VDE Verl. CY - Berlin ER - TY - CHAP A1 - Altherr, Lena A1 - Conzen, Max A1 - Elsen, Ingo A1 - Frauenrath, Tobias A1 - Lyrmann, Andreas ED - Reiff-Stephan, Jörg ED - Jäkel, Jens ED - Schwarz, André T1 - Sensor retrofitting of existing buildings in an interdisciplinary teaching project at university level T2 - Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel N2 - Existing residential buildings have an average lifetime of 100 years. Many of these buildings will exist for at least another 50 years. To increase the efficiency of these buildings while keeping costs at reasonable rates, they can be retrofitted with sensors that deliver information to central control units for heating, ventilation and electricity. This retrofitting process should happen with minimal intervention into existing infrastructure and requires new approaches for sensor design and data transmission. At FH Aachen University of Applied Sciences, students of different disciplines work together to learn how to design, build, deploy and operate such sensors. The presented teaching project already created a low power design for a combined CO2, temperature and humidity measurement device that can be easily integrated into most home automation systems KW - Building Automation KW - Smart Building KW - CO2 KW - Carbon Dioxide KW - Education Y1 - 2023 SN - 978-3-910103-01-6 U6 - https://doi.org/10.33968/2023.04 N1 - 19. AALE-Konferenz. Luxemburg, 08.03.-10.03.2023. BTS Connected Buildings & Cities Luxemburg (Tagungsband unter https://doi.org/10.33968/2023.01) SP - 31 EP - 40 PB - le-tex publishing services GmbH CY - Leipzig ER - TY - CHAP A1 - Valero, Daniel A1 - Bung, Daniel Bernhard T1 - Interfacial velocity estimation in highly aerated stepped spillway flows with a single tip fibre optical probe and Artificial Neural Networks T2 - 6th IAHR International Junior Researcher and Engineer Workshop on Hydraulic Structures, May 30th to June 1st 2016. Lübeck, Germany N2 - Air-water flows can be found in different engineering applications: from nuclear engineering to huge hydraulic structures. In this paper, a single tip fibre optical probe has been used to record high frequency (over 1 MHz) phase functions at different locations of a stepped spillway. These phase functions have been related to the interfacial velocities by means of Artificial Neural Networks (ANN) and the measurements of a classical double tip conductivity probe. Special attention has been put to the input selection and the ANN dimensions. Finally, ANN have shown to be able to link the signal rising times and plateau shapes to the air-water interfacial velocity. Y1 - 2016 U6 - https://doi.org/10.15142/T3Q590 ER - TY - CHAP A1 - Schulte, Jonas A1 - Schwager, Christian A1 - Noureldin, Kareem A1 - May, Martin A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Gradient controlled startup procedure of a molten-salt power-to-heat energy storage plant based on dynamic process simulation T2 - SolarPACES: Solar Power & Chemical Energy Systems N2 - The integration of high temperature thermal energy storages into existing conventional power plants can help to reduce the CO2 emissions of those plants and lead to lower capital expenditures for building energy storage systems, due to the use of synergy effects [1]. One possibility to implement that, is a molten salt storage system with a powerful power-to-heat unit. This paper presents two possible control concepts for the startup of the charging system of such a facility. The procedures are implemented in a detailed dynamic process model. The performance and safety regarding the film temperatures at heat transmitting surfaces are investigated in the process simulations. To improve the accuracy in predicting the film temperatures, CFD simulations of the electrical heater are carried out and the results are merged with the dynamic model. The results show that both investigated control concepts are safe regarding the temperature limits. The gradient controlled startup performed better than the temperature-controlled startup. Nevertheless, there are several uncertainties that need to be investigated further. KW - Power plants KW - Energy storage KW - Associated liquids Y1 - 2023 SN - 978-0-7354-4623-6 U6 - https://doi.org/10.1063/5.0148741 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SolarPACES: SOLAR POWER & CHEMICAL ENERGY SYSTEMS: 27th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27 September–1 October 2021, Online IS - 2815 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Oetringer, Kerstin A1 - Dümmler, Andreas A1 - Göttsche, Joachim T1 - Neues Modell zur 1D-Simulation der indirekten Verdunstungskühlung T2 - DKV‐Tagung 2020, AA II.1 N2 - Im Projekt Coolplan‐ AIR geht es um die Fortentwicklung und Feld‐ Validierung eines Berechnungs‐ und Auslegungstools zur energieeffizienten Kühlung von Gebäuden mit luftgestützten Systemen. Neben dem Aufbau und der Weiterentwicklung von Simulationsmodellen erfolgen Vermessungen der Gesamtsysteme anhand von Praxisanlagen im Feld. Eine der betrachteten Anlagen arbeitet mit indirekter Verdunstung. Diese Veröffentlichung zeigt den Entwicklungsprozess und den Aufbau des Simulationsmodells zur Verdunstungskühlung in der Simulationsumgebung Matlab‐ Simulink mit der CARNOT‐ Toolbox. Das besondere Augenmerk liegt dabei auf dem physikalischen Modell des Wärmeübertragers, in dem die Verdunstung implementiert ist. Dem neuen Modellansatz liegt die Annahme einer aus der Enthalpie‐ Betrachtung hergeleiteten effektiven Wärmekapazität zugrunde. Des Weiteren wird der Befeuchtungsgrad als konstant angesehen und eine standardisierte Zunahme der Wärmeübertragung des feuchten gegenüber dem trockenen Wärmeübertrager angenommen. Die Validierung des Modells erfolgte anhand von Literaturdaten. Für den trockenen Wärmetauscher ist der maximale absolute Fehler der berechneten Austrittstemperatur (Zuluft) kleiner als ±0.1 K und für den nassen Wärmetauscher (Kühlfall) unter der Annahme eines konstanten Verdunstungsgrades kleiner als ±0.4 K. Y1 - 2020 N1 - Deutsche Kälte- und Klimatagung, 19-20 November 2020, online SP - 250 EP - 262 ER - TY - CHAP A1 - Knackstedt, Ralf A1 - Eggert, Mathias A1 - Fleischer, Stefan T1 - The Legal Perspective on Business to Government Reporting - A Conceptual Modeling Approach and Its Application in the Financial Sector T2 - 45th Hawaii International Conference on System Sciences 2012 Y1 - 2012 SN - 978-0-7695-4525-7 U6 - https://doi.org/10.1109/HICSS.2012.576 SP - 2309 EP - 2318 ER - TY - CHAP A1 - Frotscher, Ralf A1 - Staat, Manfred T1 - An electromechanical model for cardiac tissue constructs T2 - Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon Y1 - 2015 SP - 1 EP - 4 PB - RWTH Aachen University CY - Aachen ER - TY - CHAP A1 - Rendon, Carlos A1 - Dieckmann, Simon A1 - Weidle, Mathias A1 - Dersch, Jürgen A1 - Teixeira Boura, Cristiano José A1 - Polklas, Thomas A1 - Kuschel, Marcus A1 - Herrmann, Ulf T1 - Retrofitting of existing parabolic trough collector power plants with molten salt tower systems T2 - AIP Conference Proceedings Y1 - 2018 U6 - https://doi.org/10.1063/1.5067030 VL - 2033 IS - 1 SP - 030014-1 EP - 030014-8 ER - TY - CHAP A1 - Valero, Daniel A1 - Kramer, Matthias A1 - Bung, Daniel Bernhard A1 - Chanson, Hubert T1 - A stochastic bubble generator for air-water flow research T2 - E-proceedings of the 38th IAHR World Congress, September 1-6, 2019, Panama City, Panama Y1 - 2019 U6 - https://doi.org/10.3850/38WC092019-0909 SP - 5714 EP - 5721 ER - TY - CHAP A1 - Becker, Jörg A1 - Eggert, Mathias A1 - Fleischer, Stefan A1 - Knackstedt, Ralf T1 - How to Teach Regulatory Compliant Data Warehouse Engineering? T2 - Proceedings of the Nineteenth Americas Conference on Information Systems, Chicago, Illinois, August 15-17, 2013. Y1 - 2013 N1 - AMCIS 2013 Proceedings ER - TY - CHAP A1 - Kerpen, N. B. A1 - Bung, Daniel Bernhard A1 - Schlurmann, Torsten ED - Janssen, Robert T1 - Physical model investigations of ships passing through a lock T2 - Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010 Y1 - 2010 SN - 9781742720159 SP - 93 EP - 100 PB - School of Civil Engineeering, The University of Queensland CY - Brisbane ER - TY - CHAP A1 - Bung, Daniel Bernhard T1 - Non-intrusive measuring of air-water flow properties in self-aerated stepped spillway flow T2 - Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia Y1 - 2011 SN - 978-0-85825-868-6 SP - 2380 EP - 2387 ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Schlenkhoff, Andreas ED - Pagliara, Stefano T1 - Optimization of the reaeration potential on embankment stepped spillways in skimming flow regime T2 - Hydraulic structures : proceedings of the second International Junior Researcher and Engineer Workshop on Hydraulic Structures, Pisa, Italy, 30 July-1 August 2008 Y1 - 2008 SN - 978-88-8492-568-8 SP - 97 EP - 106 ER - TY - CHAP A1 - Kerpen, N. A1 - Verworn, F. A1 - Bung, Daniel Bernhard A1 - Daemrich, K.-F. A1 - Schlurmann, Torsten T1 - Ermittlung von Wellenüberlaufmengen an Sturmflutschutzwänden auf Deichen T2 - Maritimer Wasserbau und Küsteningenieurwesen : 8. FZK-Kolloquium : Hannover 10. März, 2011 Y1 - 2011 SN - 1610-5249 SP - 63 EP - 68 ER - TY - CHAP A1 - Schlenkhoff, Andreas A1 - Bung, Daniel Bernhard T1 - Prediction of oxygen transfer in self-aerated skimming flow on embankment stepped spillways T2 - Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada Y1 - 2009 SN - 9789078046080 SP - 1 CD-ROM ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Schlenkhoff, Andreas A1 - Oertel, M. T1 - Self-aerated skimming flow on embankment stepped spillways T2 - Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada Y1 - 2009 SN - 9789078046080 SP - 1 CD-ROM ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Schlenkhoff, Andreas T1 - Selbstbelüftete Gerinneströmungen auf Treppenschussrinnen T2 - Talsperren im Wandel : 15. Deutsches Talsperrensymposium ; Beiträge zur Tagung am 14. bis 16. April 2010 im Eurogress Aachen Y1 - 2010 SN - 978-3-8322-9043-6 SP - 39 EP - 47 ER - TY - CHAP A1 - Oertel, M. A1 - Bung, Daniel Bernhard A1 - Schlenkhoff, Andreas T1 - Flash flood awareness and prevention T2 - Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada Y1 - 2009 SN - 9789078046080 SP - 1 CD-ROM ER - TY - CHAP A1 - Golland, Alexander ED - Ochs, Carsten ED - Friedewald, Michael ED - Hess, Thomas ED - Lamla, Jörn T1 - Datenschutzregulierung als Eingriff in Wertschöpfungsmodelle T2 - Die Zukunft der Datenökonomie : zwischen Geschäftsmodell, Kollektivgut und Verbraucherschutz N2 - Das Kopplungsverbot verbietet, die Nutzung einer Dienstleistung von der Erteilung einer nicht für die Leistungserbringung erforderlichen Einwilligung abhängig zu machen. Personalisierte Werbung wird hierdurch erheblich erschwert. Anbieter können jedoch durch Bereitstellung eines alternativen, einwilligungsfreien Zugangs zu derselben Leistung ihren Dienst datenschutzkonform anbieten. Ein solcher Zugang muss nicht zwingend in Form eines fixen Entgelts gestaltet sein. Vielmehr ist es datenschutzrechtlich in gewissem Umfang zulässig, Preise unter Einbeziehung personenbezogener Daten dynamisch zu gestalten. KW - Informationsgesellschaft KW - Internetökonomie KW - Digitalisierung KW - Geschäftsmodell KW - Open Data Y1 - 2019 SN - 978-3-658-27510-5 N1 - Konferenz: Zukunft der Datenökonomie 2018, 11.10-12.10.2018. Bayerische Akademie der Wissenschaften, München, Deutschland SP - 45 EP - 68 PB - Springer Fachmedien CY - Wiesbaden ER - TY - CHAP A1 - Wulfhorst, Helene A1 - Merseburg, Johannes A1 - Tippkötter, Nils T1 - Analyse von Lignocellulose mittels dynamischer Differenzkalorimetrie und Infrarot – Spektrometrie T2 - 12. Dresdner Sensor-Symposium 2015 2015-12-07 - 2015-12-09 Y1 - 2015 SN - 978-3-9813484-9-1 U6 - https://doi.org/10.5162/12dss2015/P6.2 SP - 210 EP - 215 ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Berg, Tobias A1 - Leicht-Scholten, Carmen T1 - Breaking the habit – new approaches in engineering education T2 - Proceedings of the 43rd Annual Conference of the European Society for Engineering Education N2 - Within the framework of the project a genderand diversity-oriented teaching evaluation and modern, media-supported blended learning approaches were used in order to achieve the intended goals. First research results of the literature and status quo analysis were already implemented and tested in newly designed teaching approaches, for example in a multidisciplinary introductory lecture of civil engineering at RWTH Aachen University. KW - teaching KW - engineering education KW - gender and diversity KW - best practice Y1 - 2015 SN - 978-2-87352-012-0 N1 - Annual Conference of the European Society for Engineering Education , Orléans , France , SEFI , 2015-06-29 - 2015-07-02 ER - TY - CHAP A1 - Niemueller, Tim A1 - Neumann, Tobias A1 - Henke, Christoph A1 - Schönitz, Sebastian A1 - Reuter, Sebastian A1 - Ferrein, Alexander A1 - Jeschke, Sabina A1 - Lakemeyer, Gerhard T1 - International Harting Open Source Award 2016: Fawkes for the RoboCup Logistics League T2 - RoboCup 2016: RoboCup 2016: Robot World Cup XX. RoboCup 2016 Y1 - 2017 SN - 978-3-319-68792-6 U6 - https://doi.org/10.1007/978-3-319-68792-6_53 N1 - Lecture Notes in Computer Science, LNCS, Vol 9776 SP - 634 EP - 642 PB - Springer CY - Cham ER - TY - CHAP A1 - Achenbach, Timm A1 - Geimer, K. A1 - Göttsche, Joachim A1 - Hoffschmidt, Bernhard A1 - Lynen, A. A1 - Bauer, J. T1 - Simulation and flow measurements of volumetric high temperature absorbers for solar tower power plants T2 - SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain Y1 - 2011 CY - Granada ER - TY - CHAP A1 - Teixeira Boura, Cristiano José A1 - Eckstein, J. A1 - Felinks, J. A1 - Göttsche, Joachim A1 - Hoffschmidt, Bernhard A1 - Schmitz, S. T1 - 3-D CFD simulation of an air-sand heat exchanger T2 - SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain Y1 - 2011 CY - Granada ER - TY - CHAP A1 - Achenbach, Timm A1 - Göttsche, Joachim A1 - Kaufhold, O. A1 - Hoffschmidt, Bernhard T1 - Development of an edge module for open volumetric receiver for the use of the radiation at the receiver boundary region T2 - SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain Y1 - 2011 CY - Granada ER - TY - CHAP A1 - Alexopoulos, Spiros A1 - Hoffschmidt, Bernhard A1 - Rau, Christoph T1 - Comparison of steady-state and transient simulations for solar tower power plants with open-volumetric receiver T2 - SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain Y1 - 2011 CY - Granada ER - TY - CHAP A1 - Alexopoulos, Spiros A1 - Rau, Christoph A1 - Sattler, Johannes Christoph A1 - Kronhardt, Valentina A1 - Hoffschmidt, Bernhard T1 - Simulation von Solarturmkraftwerken mit offenem volumetrischen Receiver am Standort Italien T2 - Forschung und Entwicklung für solarthermische Kraftwerke : 14. Kölner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus Jülich der FH Aachen : Kurzfassungen der Vorträge und Poster Y1 - 2011 SP - 4 S. PB - DLR CY - Köln ER - TY - CHAP A1 - Alexopoulos, Spiros A1 - Hoffschmidt, Bernhard A1 - Rau, Christoph A1 - Schmitz, M. A1 - Schwarzbözl, P. A1 - Pomp, Stefan T1 - Simulation results for a hybridized operation of a gas turbine or a burner for a small solar tower power plant T2 - SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France Y1 - 2010 SP - 82 EP - 83 PB - Soc. OSC CY - Saint Maur ER - TY - CHAP A1 - Ziolko, C. A1 - Schmitz, M. A1 - Sattler, Johannes Christoph A1 - Khedim, Ahmed A1 - Hoffschmidt, Bernhard T1 - AlSol - the open volumetric receiver technology moves to Africa T2 - SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France Y1 - 2010 SP - 93 EP - 94 PB - Soc. OSC CY - Saint Maur ER - TY - CHAP A1 - Alexopoulos, Spiros A1 - Rau, Christoph A1 - Hoffschmidt, Bernhard A1 - Breitbach, Gerd A1 - Latzke, Markus T1 - Modelling and validation of a transient heat recovery steam generator of the solar tower power plant Juelich T2 - Eurosun 2012 : Solar energy for a brighter future : conference proceedings : Rijeka, 18.-22.09.2012 Y1 - 2012 SP - ID 97 CY - Rijeka ER - TY - CHAP A1 - Anthrakidis, Anette T1 - Prüfeinrichtung zur Bestimmung der Leistungsfähigkeit von solarthermischen Kollektoren bis 200 Grad C T2 - 22. Symposium Thermische Solarenergie : 09. bis 11. Mai 2012, Kloster Banz, Bad Staffelstein Y1 - 2012 SN - 978-3-941785-89-2 SP - 134 EP - 135 PB - OTTI CY - Regensburg ER - TY - CHAP A1 - Huck, Christina A1 - Poghossian, Arshak A1 - Bäcker, Matthias A1 - Zander, W. A1 - Schubert, J. A1 - Sukoyan, L. H. A1 - Begoyan, V. A1 - Buniatyan, V. V. A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Chemische Sensoren mit Bariumstrontiumtitanat als funktionelle Schicht zur Multiparameterdetektion T2 - 11. Dresdner Sensor-Symposium : 9.-11.12.2013 Y1 - 2013 SN - 978-3-9813484-5-3 SP - 368 EP - 372 ER - TY - CHAP A1 - Schusser, Sebastian A1 - Bäcker, Matthias A1 - Leinhos, Marcel A1 - Krischer, M. A1 - Wenzel, L. A1 - Poghossian, Arshak A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Sensorkonzept zur in vitro Echtzeitmessung des Degradationsverhaltens von biodegradierbaren Biopolymeren T2 - 11. Dresdner Sensor-Symposium : 9.-11.12.2013 Y1 - 2013 SN - 978-3-9813484-5-3 SP - 174 EP - 177 ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Sun, Q. A1 - Meireles, I. A1 - Matos, J. A1 - Viseu, T. T1 - USBR type III stilling basin performance for steep stepped spillways T2 - Hydraulic structures into the 21st century : 4th IAHR International Symposium on Hydraulic Structures : 9.-11.2.2012, Porto Y1 - 2012 SN - 978-989-8509-01-7 ER - TY - CHAP A1 - Kerpen, N. B. A1 - Bung, Daniel Bernhard A1 - Schlurmann, Torsten T1 - Physical model investigations of pressure distributions next to ships passing through a lock T2 - 5th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : CG JOINT 2010 Y1 - 2010 SN - 978-7-5618-3671-2 SP - 514 EP - 519 PB - Univ. Press CY - Tianjin ER - TY - CHAP A1 - Gogolin, C. A1 - Carvalho, R. A1 - Bung, Daniel Bernhard A1 - Matos, J. T1 - Experimental and numerical investigation of steady and unsteady flows in roughened channels with cross beams T2 - 35th IAHR world congress : 8.-13.9.2013, Chengdu, China Y1 - 2013 SP - Artikelkennnummer: A10837C PB - Tsinghua Univ. Press CY - Beijing ER - TY - CHAP A1 - Oertel, Mario A1 - Bung, Daniel Bernhard T1 - Characteristics of cross-bar block ramp flows T2 - Hydraulic structures into the 21st century : 4th IAHR International Symposium on Hydraulic Structures : 9.-11.2.2012, Porto Y1 - 2012 SN - 978-989-8509-01-7 ER - TY - CHAP A1 - Schlurmann, Torsten A1 - Bung, Daniel Bernhard T1 - Experimental investigation of flow-induced radial gate vibrations at Lower Subansiri dam T2 - Sixth Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : JOINT 2012 : 23.-29.9.2012, Keelung Y1 - 2012 SP - 7 EP - 14 ER - TY - CHAP A1 - Oertel, Mario A1 - Bung, Daniel Bernhard T1 - Comparison of 2D dam-break waves with VOF and SPH method T2 - Proceedings of the 35th IAHR world congress : 8.-13.9.2013, Chengdu, China Y1 - 2013 SP - Artikelkennnummer: A11113 PB - Tsinghua Univ. Press CY - Beijing ER - TY - CHAP A1 - Bung, Daniel Bernhard T1 - Air-water surface roughness in self-aerated stepped spillway flows T2 - 35th IAHR world congress : 8.-13.9.2013, Chengdu, China Y1 - 2013 SP - Artikelkennnummer: A11045 PB - Tsinghua Univ. Press CY - Beijing ER - TY - CHAP A1 - Becker, Jörg A1 - Eggert, Mathias A1 - Bruning, Dennis A1 - Saat, Jan T1 - Applicability of Business Process Model Analysis Approaches – A Case Study in Financial Services Consulting T2 - Wirtschaftsinformatik Proceedings 2013 Y1 - 2013 N1 - 11th International Conference on Wirtschaftsinformatik, 27th February – 01st March 2013, Leipzig, Germany SP - 1181 EP - 1195 ER - TY - CHAP A1 - Sattler, Johannes Christoph A1 - Chico Caminos, Ricardo Alexander A1 - Ürlings, Nicolas A1 - Dutta, Siddharth A1 - Ruiz, Victor A1 - Kalogirou, Soteris A1 - Ktistis, Panayiotis A1 - Agathokleous, Rafaela A1 - Jung, Christian A1 - Alexopoulos, Spiros A1 - Atti, Vikrama Nagababu A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Operational experience and behaviour of a parabolic trough collector system with concrete thermal energy storage for process steam generation in Cyprus T2 - AIP Conference Proceedings N2 - As part of the transnational research project EDITOR, a parabolic trough collector system (PTC) with concrete thermal energy storage (C-TES) was installed and commissioned in Limassol, Cyprus. The system is located on the premises of the beverage manufacturer KEAN Soft Drinks Ltd. and its function is to supply process steam for the factory's pasteurisation process [1]. Depending on the factory's seasonally varying capacity for beverage production, the solar system delivers between 5 and 25 % of the total steam demand. In combination with the C-TES, the solar plant can supply process steam on demand before sunrise or after sunset. Furthermore, the C-TES compensates the PTC during the day in fluctuating weather conditions. The parabolic trough collector as well as the control and oil handling unit is designed and manufactured by Protarget AG, Germany. The C-TES is designed and produced by CADE Soluciones de Ingeniería, S.L., Spain. In the focus of this paper is the description of the operational experience with the PTC, C-TES and boiler during the commissioning and operation phase. Additionally, innovative optimisation measures are presented. Y1 - 2020 U6 - https://doi.org/10.1063/5.0029278 N1 - SOLARPACES 2019: International Conference on Concentrating Solar Power and Chemical Energy Systems, 1–4 October 2019, Daegu, South Korea IS - 2303 SP - 140004-1 EP - 140004-10 ER - TY - CHAP A1 - Schopp, Christoph A1 - Heuermann, Holger A1 - Marso, Michel T1 - Multiphysical Study of an Atmospheric Microwave Argon Plasma Jet T2 - IEEE Transactions on Plasma Science Y1 - 2017 U6 - https://doi.org/10.1109/TPS.2017.2692735 SN - 1939-9375 VL - 45 IS - 6 SP - 932 EP - 937 PB - IEEE ER - TY - CHAP A1 - Krückel, Kai A1 - Nolden, Florian A1 - Ferrein, Alexander A1 - Scholl, Ingrid T1 - Intuitive visual teleoperation for UGVs using free-look augmented reality displays T2 - 2015 IEEE International Conference on Robotics and Automation (ICRA), Seattle, WA Y1 - 2015 U6 - https://doi.org/10.1109/ICRA.2015.7139809 SP - 4412 EP - 4417 ER - TY - CHAP A1 - Butenweg, Christoph A1 - Meyer, Udo A1 - Fehling, Ekkehard T1 - INSYSME: first activities of the German partners T2 - 9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014 Y1 - 2014 ER - TY - CHAP A1 - Huck, Christina A1 - Bäcker, Matthias A1 - Poghossian, Arshak A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Bifunktionaler Sensorchip für den Nachweis von Gelöstwasserstoff Y1 - 2011 SN - 978-3942710-53-4 U6 - https://doi.org/10.5162/10dss2011/16.10 SP - 325 EP - 328 ER - TY - CHAP A1 - Neumann, Tobias A1 - Dülberg, Enno A1 - Schiffer, Stefan A1 - Ferrein, Alexander T1 - A rotating platform for swift acquisition of dense 3D point clouds T2 - Intelligent Robotics and Applications: 9th International Conference, ICIRA 2016, Tokyo, Japan, August 22-24, 2016, Proceedings, Part I Y1 - 2016 SN - 978-3-319-43505-3 (Print) SN - 978-3-319-43506-0 (Online) U6 - https://doi.org/10.1007/978-3-319-43506-0_22 N1 - Series: Lecture Notes in Computer Science (including subseries Lecture Notes in Artificial Intelligence and Lecture Notes in Bioinformatics) VL - 9834 SP - 257 EP - 268 PB - Springer ER - TY - CHAP A1 - Ludowicy, Jonas A1 - Rings, René A1 - Finger, Felix A1 - Braun, Carsten A1 - Bil, Cees T1 - Impact of Propulsion Technology Levels on the Sizing and Energy Consumption for Serial HybridElectric General Aviation Aircraft T2 - Asia Pacific International Symposium on Aerospace Technology. APISAT 2019 Y1 - 2019 ER - TY - CHAP A1 - Sattler, Johannes Christoph A1 - Alexopoulos, Spiros A1 - Chico Caminos, Ricardo Alexander A1 - Mitchell, John C. A1 - Ruiz, Victor C. A1 - Kalogirou, Soteris A1 - Ktistis, Panayiotis K. A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Dynamic simulation model of a parabolic trough collector system with concrete thermal energy storage for process steam generation T2 - AIP Conference Proceedings Y1 - 2019 U6 - https://doi.org/10.1063/1.5117663 SN - 0094243X VL - 2126 SP - 150007-1 EP - 150007-8 ER - TY - CHAP A1 - Göttsche, Joachim A1 - Korn, Michael A1 - Amato, Alexandre T1 - The Passivhaus concept for the Arabian Peninsula – An energetic-economical evaluation considering the thermal comfort T2 - QScience Proceedings: Vol 2015 N2 - The Passivhaus building standard is a concept developed for the realization of energy-efficient and economical buildings with a simultaneous high utilization comfort under European climate conditions. Major elements of the Passivhaus concept are a high thermal insulation of the external walls, the use of heat and/or solar shading glazing as well as an airtight building envelope in combination with energy-efficient technical building installations and heating or cooling generators, such as an efficient energy-recovery in the building air-conditioning. The objective of this research project is the inquiry to determine the parameters or constraints under which the Passivhaus concept can be implemented under the arid climate conditions in the Arabian Peninsula to achieve an energy-efficient and economical building with high utilization comfort. In cooperation between the Qatar Green Building Council (QGBC), Barwa Real Estate (BRE) and Kahramaa the first Passivhaus was constructed in Qatar and on the Arabian Peninsula in 2013. The Solar-Institut Jülich of Aachen University of Applied Science supports the Qatar Green Building Council with a dynamic building and equipment simulation of the Passivhaus and the neighbouring reference building. This includes simulation studies with different component configurations for the building envelope and different control strategies for heating or cooling systems as well as the air conditioning of buildings to find an energetic-economical optimum. Part of these analyses is the evaluation of the energy efficiency of the used energy recovery system in the Passivhaus air-conditioning and identification of possible energy-saving effects by the use of a bypass function integrated in the heat exchanger. In this way it is expected that on an annual basis the complete electricity demand of the building can be covered by the roof-integrated PV generator. Y1 - 2015 U6 - https://doi.org/10.5339/qproc.2015.qgbc.38 N1 - 10.5339/qproc.2015.qgbc.38 = abstract - Qatar Green Building Conference 2015 - The Vision, 38. ER - TY - CHAP A1 - Anthrakidis, Anette A1 - Herrmann, Ulf A1 - Schorn, Christian A1 - Schwarzer, Klemens A1 - Wedding, Philipp A1 - Weis, Fabian T1 - Development and Testing of a Novel Method for the Determination of the Efficiency of Concentrating Solar Thermal Collectors T2 - Conference Proceedings Solar World Congress 2015, Daegu, Korea, 08 – 12 November 2015 Y1 - 2015 ER - TY - CHAP A1 - Näther, Niko A1 - Poghossian, Arshak A1 - Platen, J. A1 - Yoshinobu, T. A1 - Koudelka-Hep, M. A1 - Schöning, Michael Josef T1 - Multi-parameter sensing of both physical and (bio-)chemical quantities using the same transducer principle T2 - Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ... Y1 - 2006 SP - 172 EP - 181 CY - Warsaw ER - TY - CHAP A1 - Heitzer, M. A1 - Staat, Manfred T1 - Direct FEM approach to design-by-analysis of pressurized components N2 - Abstracts of the ACHEMA 2000 - International Meeting on Chemical Engineering, Environmental Protection and Biotechnology, May 22 - 27, 2000. Frankfurt am Main. Achema 2000 : special edition / Linde. [Ed.: Linde AG. Red.: Volker R. Leski]. - Wiesbaden : Linde AG, 2000. - 56 p. : Ill., . - pp: 79 - 81 N2 - Abstracts der ACHEMA 2000 - International Meeting on Chemical Engineering, Environmental Protection and Biotechnology, May 22 - 27, 2000. Frankfurt am Main. KW - Finite-Elemente-Methode KW - Finite-Elemente-Methode KW - limit analysis KW - shakedown analysis Y1 - 2000 ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Langohr, Phillip A1 - Waldenberger, Lisa ED - Habersack, Helmut ED - Tritthart, Michael T1 - Influence of cycle number in CFD studies of labyrinth weirs T2 - Proceedings of the 40th IAHR World Congress (Vienna, 2023) N2 - The major advantage of labyrinth weirs over linear weirs is hydraulic efficiency. In hydraulic modeling efforts, this strength contrasts with limited pump capacity as well as limited computational power for CFD simulations. For the latter, reducing the number of investigated cycles can significantly reduce necessary computational time. In this study, a labyrinth weir with different cycle numbers was investigated. The simulations were conducted in FLOW-3D HYDRO as a Large Eddy Simulation. With a mean deviation of 1.75 % between simulated discharge coefficients and literature design equations, a reasonable agreement was found. For downstream conditions, overall consistent results were observed as well. However, the orientation of labyrinth weirs with a single cycle should be chosen carefully under consideration of the individual research purpose. KW - CFD KW - Large Eddy Simulation KW - Labyfrinth weirs Y1 - 2023 SN - 978-90-833476-1-5 U6 - https://doi.org/10.3850/978-90-833476-1-5_iahr40wc-p0531-cd SN - L 2521-7119 (online) N1 - Vienna, Austria, from August 21 to 25, 2023 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - CHAP A1 - Heuermann, Holger A1 - Finger, Torsten T1 - 2.45 GHz Plasma Powered Spark Plug by Thermal and EM-Optimization Y1 - 2014 N1 - Ansys High Frequency Simulation Conference - AHFSC 2014, Munich; 02/2014 ER - TY - CHAP A1 - Gömmel, Andreas A1 - Niendorf, Thoralf A1 - Frauenrath, Tobias A1 - Otten, Mario A1 - Butenweg, Christoph A1 - Kob, Malte T1 - 3D vocal fold geometry mapping using Magnetic Resonance Imaging T2 - Fortschritte der Akustik : 36. Deutsche Jahrestagung für Akustik, Band 1 Y1 - 2010 SN - 978-3-9808659-8-2 N1 - Fortschritte der Akustik : 36. Deutsche Jahrestagung für Akustik ; 15.-18. März 2010, Berlin SP - 271 EP - 272 PB - Deutsche Gesellschaft für Akustik CY - Berlin ER - TY - CHAP A1 - Schildt, P. A1 - Braun, Carsten A1 - Marcocca, P. T1 - Flight testing the extra 330LE flying testbed T2 - 48th Annual International Symposium of the Society of Flight Test Engineers 2017 Y1 - 2017 SN - 978-151085387-4 N1 - 48th Annual International Symposium of the Society of Flight Test Engineers 2017, SFTE 2017; Destin; United States; 30 October 2017 through 2 November 2017 SP - 349 EP - 362 ER - TY - CHAP A1 - Al-Kaidy, H. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - A platform technology for the automated reaction control in magnetizable micro-fluidic droplets T2 - Biomaterials - made in bioreactors : book of abstracts, May 26 - 28, 2014, Radisson Blu Park Hotel and Conference Dentre, Radebeul, Germany Y1 - 2014 SP - 21 EP - 22 PB - DECHEMA CY - Frankfurt am Main ER - TY - CHAP A1 - Finger, Felix A1 - Götten, Falk A1 - Braun, Carsten A1 - Bil, C. T1 - On Aircraft Design Under the Consideration of Hybrid-Electric Propulsion Systems T2 - APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018) N2 - A hybrid-electric propulsion system combines the advantages of fuel-based systems and battery powered systems and offers new design freedom. To take full advantage of this technology, aircraft designers must be aware of its key differences, compared to conventional, carbon-fuel based, propulsion systems. This paper gives an overview of the challenges and potential benefits associated with the design of aircraft that use hybrid-electric propulsion systems. It offers an introduction of the most popular hybrid-electric propulsion architectures and critically assess them against the conventional and fully electric propulsion configurations. The effects on operational aspects and design aspects are covered. Special consideration is given to the application of hybrid-electric propulsion technology to both unmanned and vertical take-off and landing aircraft. The authors conclude that electric propulsion technology has the potential to revolutionize aircraft design. However, new and innovative methods must be researched, to realize the full benefit of the technology. KW - Hybrid-electric aircraft KW - Aircraft design KW - Design rules KW - Green aircraft Y1 - 2019 SN - 978-981-13-3305-7 U6 - https://doi.org/10.1007/978-981-13-3305-7_99 N1 - APISAT 2018 - Asia-Pacific International Symposium on Aerospace Technology. 16-18 October 2018. Chengdu, China. Lecture Notes in Electrical Engineering (LNEE, volume 459) SP - 1261 EP - 1272 PB - Springer CY - Singapore ER - TY - CHAP A1 - Oertel, Mario A1 - Bung, Daniel Bernhard A1 - Schlenkhoff, Andreas ED - Carstensen, Dirk T1 - Blocksteinrampen in Riegelbauweise : Neue Bemessungsansätze T2 - Staubauwerke : planen, bauen, betreiben; 35. Dresdner Wasserbaukolloquium 2012, 08. - 09. März 2012 Y1 - 2012 SN - 978-3-86780-261-1 SP - 317 EP - 326 PB - Selbstverl. der Techn. Univ. CY - Dresden ER - TY - CHAP A1 - Becker, Jörg A1 - Eggert, Mathias A1 - Saat, Jan A1 - Dirding, Philipp T1 - The Influence of Regulation on Data Warehouse Engineering – Investigating an IT Consulting Case in the Financial Service Industry T2 - Proceedings of the Nineteenth Americas Conference on Information Systems, Chicago, Illinois, August 15-17, 2013. Y1 - 2013 SP - 1 EP - 8 ER - TY - CHAP A1 - Luft, Angela A1 - Gebhardt, Andreas A1 - Balc, Nicolae T1 - Challenges of additive manufacturing in production systems T2 - Modern technologies in manufacturing (MTeM 2019) Y1 - 2019 U6 - https://doi.org/10.1051/matecconf/201929901003 N1 - MATEC Web of Conferences 299; MTeM 2019 VL - 299 IS - Article 01003 ER - TY - CHAP A1 - Schopp, Christoph A1 - Heuermann, Holger A1 - Holtrup, S. T1 - Investigation on efficacy optimization of RF-driven automotive D-lamps T2 - 44th European Microwave Conference (EuMC),2014, Rome Y1 - 2014 U6 - https://doi.org/10.1109/EuMC.2014.6986645 SP - 1154 EP - 1157 ER - TY - CHAP A1 - Tippkötter, Nils A1 - Möhring, S. A1 - Maurer, S. A1 - Roth, J. T1 - Dezentrale Vorbehandlung und Verarbeitung pflanzlicher Reststoffe für Bioraffinerien T2 - Kurzfassungen der Vorträge nach Sessions : Frühjahrstagung der Biotechnologen 2013, 4. - 5. März 2013, Dechema-Haus, Frankfurt am Main Y1 - 2013 SP - 5 CY - Frankfurt am Main ER - TY - CHAP A1 - Tippkötter, Nils T1 - Biotechnologische Gewinnung von Wertstoffen aus Molke : BiobasedWorld - Innovation in food T2 - Biotechnica 2013 : European biotechnology science & industry news Y1 - 2013 VL - 12 IS - 9, special SP - 33 EP - 50 ER - TY - CHAP A1 - Wolf, Martin R. A1 - Ulbrich, Daniel T1 - Decision-Support-System kokas zur Sanierungsplanung und Strategieentwicklung N2 - Dr.-Ing. Martin Wolf ; Dipl.-Kaufm. Daniel Ulbrich , Dr. Pecher und Partner Ingenieurgesellschaft mbH, München. 31 S. (S. 139-168). Beitrag zum 1. Aachener Softwaretag in der Wasserwirtschaft < 1, 2007, Aachen>. Zusammenfasung [der Autoren] Die öffentlichen Kanalnetze Deutschlands stellen mit einem Wert von rd. 330 Mrd. € ein enormes Anlagevermögen dar. Auf Grund des oft schlechten Zustandes und geringer Ausgaben zur Instandhaltung und Erneuerung ist zu erwarten, dass durch die gegenwärtige Sanierungspraxis eher ein Substanzwertverzehr des Kanalnetzes als ein Substanzwerterhalt im Sinne des Generationenvertrages erzielt wird. Für einen nachhaltigen Betrieb und Erhalt der Kanalnetze sind deshalb Sanierungsstrategien erforderlich, die neben den technischen und gesetzlichen Anforderungen auch den mittel- und langfristigen Substanzwertverlauf berücksichtigen. Dieser wird beeinflusst vom erforderlichen oder durchgeführten Sanierungsumfang, Art und Zusammensetzung der ausgewählten Maßnahmen sowie der zeitlichen Abfolge der Sanierungsmaßnahmen. Erheblichen Einfluss auf den Substanzwertverlauf hat zudem die Berücksichtigung der hydraulischen Verhältnisse sowie der optisch nicht sichtbaren Undichtheiten. Entsprechend ist es erforderlich, die tatsächlich vorhandenen Defizite zu ermitteln und die Sanierungsmaßnahmen sowie eine Strategie zur Umsetzung zu erarbeiten. Da sich gezeigt hat, dass alleine die Einhaltung der technischen und gesetzlichen Anforderung für einen Substanzwerterhalt nicht ausreicht, muss die geplante Strategie im Dr.-Ing. Martin Wolf 139 von 170 Decision-Support-System kokas zur Sanierungsplanung und Strategieentwicklung 1. Aachener Softwaretag in der Wasserwirtschaft Hinblick auf die nachhaltige Wertentwicklung überprüft und ggf. Anpassungen vorgenommen werden. Kurzfristig erzielte Einsparungen durch reduzierten Schadensumfang oder einseitige Maßnahmenwahl ermöglichen zwar im günstigsten Fall, die Anforderungen einzuhalten, gehen jedoch zwangsläufig zu Lasten des Substanzwertes und führen mittel- und langfristig zu einer Verschärfung der Kosten- und Gebührensituation. Der monetäre, am konkreten Sanierungsaufwand orientierte Substanzwertansatz ermöglicht dabei, technische und kaufmännische Gesichtspunkte praxisnah zu verknüpfen und den bestmöglichen Ausgleich zwischen den gegenläufigen Zielen Substanzwerterhalt und Gebührenkonstanz zu finden. KW - Kanalisation KW - Kanalsanierung Y1 - 2007 ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Oertel, Mario T1 - Wave breaking over a submerged horizontal plate: Optical Flow, LES and RANS T2 - E-proceedings of the 38th IAHR World Congress September 1-6, 2019, Panama City, Panama Y1 - 2019 U6 - https://doi.org/10.3850/38WC092019-0509 SP - 3690 EP - 3698 ER - TY - CHAP A1 - Ludowicy, Jonas A1 - Rings, René A1 - Finger, Felix A1 - Braun, Carsten T1 - Sizing Studies of Light Aircraft with Serial Hybrid Propulsion Systems T2 - Luft- und Raumfahrt - Digitalisierung und Vernetzung : Deutscher Luft- und Raumfahrtkongress 2018. 4. - 6. September 2018 - Friedrichshafen Y1 - 2018 ER - TY - CHAP A1 - Neumann, Tobias A1 - Ferrein, Alexander A1 - Kallweit, Stephan A1 - Scholl, Ingrid T1 - Towards a mobile mapping robot for underground mines T2 - 7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town Y1 - 2014 SP - 1 EP - 6 ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Tullis, Blake T1 - Hydraulic Structures - ISHS2018 in Perspective T2 - 7th IAHR International Symposium on Hydraulic Structures, Aachen, Germany, 15-18 May Y1 - 2018 SN - 978-0-692-13277-7 U6 - https://doi.org/10.15142/T3WH2B ER - TY - CHAP A1 - Ludowicy, Jonas A1 - Rings, René A1 - Finger, Felix A1 - Braun, Carsten T1 - Sizing Studies of Light Aircraft with Parallel Hybrid Propulsion Systems T2 - Deutscher Luft- und Raumfahrtkongress 2018 Y1 - 2018 U6 - https://doi.org/10.25967/480227 ER - TY - CHAP A1 - Thurn, Laura A1 - Gebhardt, Andreas T1 - Strategy of Education on Materials for Students T2 - Conference Proceedings: „New Perspectives in Science Education" Y1 - 2018 SN - 978-88-6292-976-9 SP - 156 EP - 161 CY - Florence, Italy ER - TY - CHAP A1 - Butenweg, Christoph A1 - Gajewski, R. A1 - Thierauf, Georg T1 - A practical approach for the optimum design of reinforced concrete structures T2 - Developments in computational mechanics with high performance computing : [papers presented at the Third Euro-Conference on Parallel and Distributed Computing for Computational Mechanics, held in Weimar, Germany between 20 - 25 March 1999] / ed. by B. H. V. Topping Y1 - 1999 SN - 0-94-8749-59-8 SP - 245 EP - 250 PB - Civil-Comp Press CY - Edinburgh ER - TY - CHAP A1 - Paulsen, Svea A1 - Hoffstadt, Kevin A1 - Krafft, Simone A1 - Leite, A. A1 - Zang, J. A1 - Fonseca-Zang, W. A1 - Kuperjans, Isabel T1 - Continuous biogas production from sugarcane as sole substrate T2 - Energy Reports N2 - A German–Brazilian research project investigates sugarcane as an energy plant in anaerobic digestion for biogas production. The aim of the project is a continuous, efficient, and stable biogas process with sugarcane as the substrate. Tests are carried out in a fermenter with a volume of 10 l. In order to optimize the space–time load to achieve a stable process, a continuous process in laboratory scale has been devised. The daily feed in quantity and the harvest time of the substrate sugarcane has been varied. Analyses of the digester content were conducted twice per week to monitor the process: The ratio of inorganic carbon content to volatile organic acid content (VFA/TAC), the concentration of short-chain fatty acids, the organic dry matter, the pH value, and the total nitrogen, phosphate, and ammonium concentrations were monitored. In addition, the gas quality (the percentages of CO₂, CH₄, and H₂) and the quantity of the produced gas were analyzed. The investigations have exhibited feasible and economical production of biogas in a continuous process with energy cane as substrate. With a daily feeding rate of 1.68gᵥₛ/l*d the average specific gas formation rate was 0.5 m3/kgᵥₛ. The long-term study demonstrates a surprisingly fast metabolism of short-chain fatty acids. This indicates a stable and less susceptible process compared to other substrates. Y1 - 2020 U6 - https://doi.org/10.1016/j.egyr.2019.08.035 N1 - 6th International Conference on Energy and Environment Research, ICEER 2019, 22–25 July, University of Aveiro, Portugal VL - 6 IS - Supplement 1 SP - 153 EP - 158 PB - Elsevier ER - TY - CHAP A1 - Neth, Jannik A1 - Schuba, Marko A1 - Brodkorb, Karsten A1 - Neugebauer, Georg A1 - Höner, Tim A1 - Hack, Sacha T1 - Digital forensics triage app for android T2 - ARES '23: Proceedings of the 18th International Conference on Availability, Reliability and Security N2 - Digital forensics of smartphones is of utmost importance in many criminal cases. As modern smartphones store chats, photos, videos etc. that can be relevant for investigations and as they can have storage capacities of hundreds of gigabytes, they are a primary target for forensic investigators. However, it is exactly this large amount of data that is causing problems: extracting and examining the data from multiple phones seized in the context of a case is taking more and more time. This bears the risk of wasting a lot of time with irrelevant phones while there is not enough time left to analyze a phone which is worth examination. Forensic triage can help in this case: Such a triage is a preselection step based on a subset of data and is performed before fully extracting all the data from the smartphone. Triage can accelerate subsequent investigations and is especially useful in cases where time is essential. The aim of this paper is to determine which and how much data from an Android smartphone can be made directly accessible to the forensic investigator – without tedious investigations. For this purpose, an app has been developed that can be used with extremely limited storage of data in the handset and which outputs the extracted data immediately to the forensic workstation in a human- and machine-readable format. KW - Android KW - Digital triage KW - Triage-app Y1 - 2023 SN - 9798400707728 U6 - https://doi.org/10.1145/3600160.3605017 N1 - ARES 2023: The 18th International Conference on Availability, Reliability and Security. August 29 - September 1, 2023. Benevento, Italy. PB - ACM ER - TY - CHAP A1 - Neugebauer, Georg A1 - Brutschy, Lucas A1 - Meyer, Ulrike A1 - Wetzel, Susanne ED - Garcia-Alfaro, Joaquin ED - Lioudakis, Georgios ED - Cuppens-Boulahia, Nora ED - Foley, Simon ED - Fitzgerald, William M. T1 - Privacy-preserving multi-party reconciliation secure in the malicious model T2 - DPM 2013, SETOP 2013: Data Privacy Management and Autonomous Spontaneous Security N2 - The problem of fair and privacy-preserving ordered set reconciliation arises in a variety of applications like auctions, e-voting, and appointment reconciliation. While several multi-party protocols have been proposed that solve this problem in the semi-honest model, there are no multi-party protocols that are secure in the malicious model so far. In this paper, we close this gap. Our newly proposed protocols are shown to be secure in the malicious model based on a variety of novel non-interactive zero-knowledge-proofs. We describe the implementation of our protocols and evaluate their performance in comparison to protocols solving the problem in the semi-honest case. KW - Privacy-enhancing technologies KW - Secure multi-party computation KW - Cryptographic protocols KW - Zero-knowledge proofs KW - Malicious model Y1 - 2014 SN - 978-3-642-54567-2 (Print) SN - 978-3-642-54568-9 (Online) U6 - https://doi.org/10.1007/978-3-642-54568-9_12 N1 - 8th International Workshop, DPM 2013, and 6th International Workshop, SETOP 2013, Egham, UK, September 12-13, 2013. Part of the Lecture Notes in Computer Science book series (LNSC,volume 8247) SP - 178 EP - 193 PB - Springer CY - Berlin ER - TY - CHAP A1 - Sildatke, Michael A1 - Karwanni, Hendrik A1 - Kraft, Bodo A1 - Schmidts, Oliver A1 - Zündorf, Albert T1 - Automated Software Quality Monitoring in Research Collaboration Projects T2 - ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops N2 - In collaborative research projects, both researchers and practitioners work together solving business-critical challenges. These projects often deal with ETL processes, in which humans extract information from non-machine-readable documents by hand. AI-based machine learning models can help to solve this problem. Since machine learning approaches are not deterministic, their quality of output may decrease over time. This fact leads to an overall quality loss of the application which embeds machine learning models. Hence, the software qualities in development and production may differ. Machine learning models are black boxes. That makes practitioners skeptical and increases the inhibition threshold for early productive use of research prototypes. Continuous monitoring of software quality in production offers an early response capability on quality loss and encourages the use of machine learning approaches. Furthermore, experts have to ensure that they integrate possible new inputs into the model training as quickly as possible. In this paper, we introduce an architecture pattern with a reference implementation that extends the concept of Metrics Driven Research Collaboration with an automated software quality monitoring in productive use and a possibility to auto-generate new test data coming from processed documents in production. Through automated monitoring of the software quality and auto-generated test data, this approach ensures that the software quality meets and keeps requested thresholds in productive use, even during further continuous deployment and changing input data. Y1 - 2020 U6 - https://doi.org/10.1145/3387940.3391478 N1 - ICSE '20: 42nd International Conference on Software Engineering, Seoul, Republic of Korea, 27 June 2020 - 19 July 2020 SP - 603 EP - 610 PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Kurz, Melanie ED - Feijs, Loe T1 - On the benefit of moving images for the evaluation of form in virtual space : reflections in model theory T2 - Design and semantics of form and movement : DeSForM 2008 ; [Hochschule für Gestaltung Offenbach am Main, 6.-7.11.2008] Y1 - 2008 SN - 978-90-809801-2-9 SP - 31 EP - 34 PB - Philips CY - Eindhoven ER -