TY  - CHAP
A1  - Mertens, Josef
ED  - Sobieczky, H.
T1  - Supersonic laminar flow
T2  - New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366)
N2  - Supersonic transports are very drag sensitive. Technology to reduce drag by application of laminar flow, therefore, will be important; it is a prerequisite to achieve very long range capability. In earlier studies it was assumed that SCTs would only become possible by application of laminar flow [376]. But today, we request an SCT to be viable without application of laminar flow in order to maintain its competitiveness when laminar flow becomes available for subsonic and supersonic transports. By reducing fuel burned, laminar flow drag reduction reduces size and weight of the aircraft, or increases range capability -whereas otherwise size and weight would grow towards infinity. Transition mechanisms from laminar to turbulent state of the boundary layer flow (ALT, CFI, TSI) function as for transonic transports, but at more severe conditions: higher sweep angles, cooled surfaces; higher mode instabilities (HMI) must at least be taken into account, although they may not become important below Mach 3. Hitherto there is a worldwide lack of ground test facilities to investigate TSI at the expected cruise Mach numbers between 1.6 and 2.4; in Stuttgart, Germany one such facility -a Ludwieg tube- is still in the validation phase. A quiet Ludwieg tunnel could be a favourable choice for Europe. But it will require a new approach in designing aircraft which includes improved theoretical predictions, usage of classical wind tunnels for turbulent flow and flight tests for validation.
KW  - Wind Tunnel
KW  - Flight Test
KW  - Supersonic Wind Tunnel
KW  - Parabolized Stability Equation
Y1  - 1997
SN  - 3-2118-2815-X
U6  - http://dx.doi.org/10.1007/978-3-7091-2658-5_18
SP  - 275
EP  - 290
PB  - Springer
CY  - Wien [u.a.]
ER  - 
TY  - CHAP
A1  - Mertens, Josef
ED  - Sobieczky, H.
T1  - Son of Concorde, a technology challenge
T2  - New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366)
N2  - Concorde (Figure 9) is the only supersonic airliner which has been introduced into regular passenger service. It is still in service at British Airways and Air France without any flight accidents, and probably will stay in service for at least for ten more years.
KW  - Technology Challenge
KW  - Multidisciplinary Design Optimization
KW  - Specific Fuel Consumption
KW  - Engine Efficiency
KW  - Sonic Boom
Y1  - 1997
SN  - 3-2118-2815-X
U6  - http://dx.doi.org/10.1007/978-3-7091-2658-5_3
SP  - 31
EP  - 51
PB  - Springer
CY  - Wien [u.a.]
ER  - 
TY  - JOUR
A1  - Mertens, Josef
T1  - Charakteristiken des Staub-Gas-Gemisches
JF  - Zeitschrift für angewandte Mathematik und Mechanik : ZAMM. 65 (1985), H. 4
Y1  - 1985
SN  - 1521-4001
SP  - T211
EP  - T213
ER  - 
TY  - BOOK
A1  - Mertens, Josef
T1  - Instationäre Strömungen von Gasen mit brennbaren Partikeln
Y1  - 1983
N1  - Aachen, Techn. Hochschule, Diss., 1983
CY  - Aachen
ER  - 
TY  - CHAP
A1  - Mertens, Josef
T1  - Next steps envisaged to improve wing performance of commercial aircraft
T2  - Aerodynamic drag reduction technologies : proceedings of the CEAS/DragNet European Drag Reduction Conference, 19–21 June 2000, Potsdam, Germany. - (Notes on numerical fluid mechanics ; 76)
Y1  - 2001
SN  - 3-540-41911-X (Print)
SN  - 978-3-540-45359-8 (Elektronisch)
U6  - http://dx.doi.org/10.1007/978-3-540-45359-8_26
SP  - 246
EP  - 255
PB  - Springer
CY  - Berlin [u.a.]
ER  - 
TY  - CHAP
A1  - Mertens, Josef
T1  - Reduction of aerodynamic drag (RaWid)-Status after the first year of the program
T2  - New results in numerical and experimental fluid mechanics. - (Notes on numerical fluid mechanics ; 60)
N2  - The technology programme “Reduction of aerodynamic drag (RaWid)” for high speed aerodynamics at Daimler-Benz Aerospace Airbus is sponsered by the German ministry for education, research and technology since July 1, 1995. Connected to this industrial programme are the cooperation programmes “MEGAFLOW” under leadership of the DLR and “Transition” by the DFG, and several contributions by DLR and universities.

The programme is oriented towards technologies required for a MEGALINER which gains momentum by the ambitious plans for a new large Airbus A3XX.

In the first year new technological steps were undertaken in theory, design and experiment. Some critical steps were verified by wing designs checked in wind tunnel tests.
KW  - Wind Tunnel
KW  - Aerodynamic Drag
KW  - Flight Test
KW  - Friction Drag
Y1  - 1997
SN  - 3-528-06960-0
U6  - http://dx.doi.org/10.1007/978-3-322-86573-1_2
SP  - 7
EP  - 14
PB  - Vieweg
CY  - Braunschweig [u.a.]
ER  - 
TY  - JOUR
A1  - Mertens, Josef
T1  - Luft hat keine Balken, aber enorme Kräfte : Aerodynamik - die unsichtbare Kraft
JF  - HEmagazin : das Hocheffizienz-Magazin von Wilo. 2006 (2006), H. 1
Y1  - 2006
SP  - 4
EP  - 9
PB  - -
ER  - 
TY  - JOUR
A1  - Mertens, Josef
T1  - Required technologies for supersonic aircraft
JF  - Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamic research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998
Y1  - 1998
SN  - 92-837-1007-X
N1  - (RTO educational notes ; 4)
SP  - 5.1
EP  - 5.16
PB  - Research and Technology Organization
CY  - Neuilly-sur-Seine
ER  - 
TY  - JOUR
A1  - Mertens, Josef
T1  - Multi point design challenges for supersonic transports
JF  - Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamics research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998
Y1  - 1998
SN  - 92-837-1007-X
SP  - 8.1
EP  - 8.12
PB  - Research and Technology Organization
CY  - Neuilly-sur-Seine
ER  - 
TY  - JOUR
A1  - Mertens, Josef
T1  - Laminar flow for supersonic transports
JF  - Proceedings : March 16 - 18, 1992, Congress Centrum, Hamburg, Federal Republic of Germany / organized jointly by: Deutsche Gesellschaft für Luft- und Raumfahrt e.V. ... [Programme committee J. Szodruch ...]
Y1  - 1992
SN  - 3-922010-73-3
N1  - DGLR-Bericht ; 92,06
SP  - 319
EP  - 323
PB  - DGLR
CY  - Bonn
ER  - 
TY  - JOUR
A1  - Mertens, Josef
T1  - Aerodynamische Ziele des Adaptiven Flügels (ADIF).
JF  - DGLR-Jahrbuch 1998 Bd. 1
Y1  - 1998
N1  - DGLR-JT98-213
SP  - 47
EP  - 52
ER  - 
TY  - JOUR
A1  - Mertens, Josef
T1  - Einige herausragende Ergebnisse des Technologieprogramms "Reduktion des Aerodynamischen Widerstands (RaWid)"
JF  - DGLR-Jahrbuch 1999 Bd. 3
Y1  - 1999
N1  - DGLR-JT99-047
SP  - 1461
EP  - 1468
ER  - 
TY  - BOOK
A1  - Mertens, Josef
T1  - Reduktion des aerodynamischen Widerstands (RaWid) : Abschlußbericht ; Laufzeit des Vorhaben, Berichtszeitraum: 01.07.1995 bis 31.12.1998 / Verf.: J. Mertens
Y1  - 1999
N1  - Förderkenzeichen BMBF 20 A 9595 A. Engl. Zsfassung u.d.T.: Reduction of aerodynamis drag (RaWid) - final report . auch als elektronisches Dokument vorh.
PB  - DaimlerChrysler Aerospare Airbus GmbH
CY  - Hamburg
ER  - 
TY  - BOOK
A1  - Mertens, Josef
T1  - Reduktion des aerodynamischen Widerstands (RaWid) : Abschlußbericht ; Laufzeit des Vorhaben, Berichtszeitraum: 01.07.1995 bis 31.12.1998 / Verf.: J. Mertens
Y1  - 1999
N1  - Parallel als gedruckte Ausgabe erschienen
PB  - DaimlerChrysler Aerospare Airbus GmbH
CY  - Hamburg
ER  - 
TY  - CHAP
A1  - Mertens, Josef
ED  - Nitsche, Wolfgang
T1  - Some important results of the technology programme RaWid
T2  - New Results in Numerical and Experimental Fluid Mechanics : Contributions to the 11th AG STAB/DGLR Symposium Berlin, Germany 1998. - Vol. 2. - (Notes on Numerical Fluid Mechanics ; 72)
Y1  - 1999
SN  - 978-3-663-10903-7 (Print)
SN  - 978-3-663-10901-3 (Elektronisch)
U6  - http://dx.doi.org/10.1007/978-3-663-10901-3_41
SP  - 315
EP  - 322
PB  - Springer Fachmedien
CY  - Wiesbaden
ER  - 
TY  - CHAP
A1  - Mertens, Josef
A1  - Becker, K.
ED  - Ballmann, Josef
T1  - Numerical solution of flow equations : an aircraft designer's view
T2  - Nonlinear hyperbolic equations - theory, computation methods, and applications : proceedings of the 2nd International Conference on Nonlinear Hyperbolic Problems, Aachen, FRG, March 14 to 18, 1988. - (Notes on Numerical Fluid Mechanics ; 24)
N2  - Today the most accurate and cost effective industrial codes used in aircraft design are based on the full potential equation coupled with boundary layer equations. However, these are not capable to solve complicated three-dimensional problems of vortical flows and shocks. On the other hand Euler and Navier-Stokes codes are too expensive and not accurate enough for design purposes, especially in regard of drag and interference prediction. The reasons for these deficiencies are investigated and a way to overcome them by future developments is demonstrated.
Y1  - 1989
SN  - 3-528-08098-1
U6  - http://dx.doi.org/10.1007/978-3-322-87869-4_41
N1  - International Conference on Nonlinear Hyperbolic Problems <3, 1988, Aachen>
SP  - 403
EP  - 412
PB  - Vieweg
CY  - Braunschweig
ER  - 
TY  - JOUR
A1  - Mertens, Josef
A1  - Henke, Rolf
T1  - Adaptive technologies for future civil air transport
JF  - Air & Space Europe. 3 (2001), H. 3-4
Y1  - 2001
SN  - 1247-5793
SP  - 80
EP  - 82
ER  - 
TY  - JOUR
A1  - Mertens, Josef
A1  - Hünecke, Klaus
T1  - Experimentelle Untersuchung zur Landeeigenschaft von Hyperschall-Fluggeräten / Hünecke, Klaus ; Mertens, Josef
JF  - DGLR-Jahrbuch 1988 Bd. 1
Y1  - 1988
N1  - DGLR-88-123
SP  - 706
ER  - 
TY  - JOUR
A1  - Mertens, Josef
A1  - Kelm, R.
A1  - Velden, A. van der
T1  - Interdisziplinäre Auslegung eines Verkehrsflugzeugflügels
JF  - DGLR-Jahrbuch 1999 Bd. 3
Y1  - 1999
N1  - DGLR-JT99-156
SP  - 1605
EP  - 1610
ER  - 
TY  - JOUR
A1  - Mertens, Josef
A1  - Klevenhusen, K. D.
A1  - Jakob, H.
T1  - Accurate Transonic Wave Drag Prediction Using Simple Physical Models
JF  - AIAA-Journal. 25 (1987), H. 6
Y1  - 1987
SN  - 0001-1452
SP  - 799
EP  - 805
ER  - 
TY  - PAT
A1  - Mertens, Josef
A1  - Lajain, Henri
T1  - Method of fabricating leading edge nose structures of aerodynamic surfaces : patent no.: US 6,415,510 B2 ; date of patent: Jul. 9, 2002
Y1  - 2002
N1  - Volltext auch in der Datenbank http://publikationen.dpma.de/ zu finden unter der Nummer US000006415510B2
PB  - United States Patent and Trademark Office
CY  - [Washington, DC]
ER  - 
TY  - JOUR
A1  - Mertens, Josef
A1  - Röger, Wolf
T1  - F-Schlepp: Problem Taumelschwingung
JF  - Aerokurier. 44 (2000), H. 10
Y1  - 2000
SN  - 0341-1281
N1  - in der Bereichsbibliothek unter der Signatur 23 Z 391-2000
SP  - 73
EP  - 73
ER  - 
TY  - PAT
A1  - Mertens, Josef
A1  - Velden, Alexander van der
A1  - Kelm, Roland
T1  - Flugzeug mit Flügeln, deren maximaler Auftrieb durch steuerbare Flügelkomponenten veränderbar ist : Offenlegungsschrift DE102004045732 ; Offenlegungstag: 30.03.2006 = Aircraft with wings whose maximum lift can be altered by controllable wing components
Y1  - 2006
N1  - Zugleich EP1791755A1. - Volltext über Datenbank: http://publikationen.dpma.de/
PB  - Deutsches Patent- und Markenamt
CY  - München
ER  - 
TY  - BOOK
A1  - Mertens, Josef
A1  - Velden, Alexander van der
A1  - Kelm, Roland
A1  - Kokan, David
T1  - Application of MDO to large subsonic transport aircraft
Y1  - 2000
N1  - Aerospace Sciences Meeting and Exhibit <38, 2000, Reno, NV> ; (AIAA Paper ; 00-0844)
PB  - American Institute of Aeronautics and Astronautics
CY  - Reston, Va.
ER  - 
TY  - JOUR
A1  - Meyer, Max-Arno
A1  - Granrath, Christian
A1  - Feyerl, Günter
A1  - Richenhagen, Johannes
A1  - Kaths, Jakob
A1  - Andert, Jakob
T1  - Closed-loop platoon simulation with cooperative intelligent transportation systems based on vehicle-to-X communication
JF  - Simulation Modelling Practice and Theory
Y1  - 2021
U6  - http://dx.doi.org/10.1016/j.simpat.2020.102173
SN  - 1569-190X
VL  - 106
IS  - Art. 102173
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Möhren, Felix
A1  - Bergmann, Ole
A1  - Janser, Frank
A1  - Braun, Carsten
T1  - On the determination of harmonic propeller loads
T2  - AIAA SCITECH 2023 Forum
N2  - Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures.
Y1  - 2023
U6  - http://dx.doi.org/10.2514/6.2023-2404
N1  - AIAA SCITECH 2023 Forum, 23-27 January 2023, National Harbor, MD & Online
PB  - AIAA
ER  - 
TY  - JOUR
A1  - Neu, Eugen
A1  - Janser, Frank
A1  - Khatibi, Akbar A.
A1  - Braun, Carsten
A1  - Orifici, Adrian C.
T1  - Operational Modal Analysis of a wing excited by transonic flow
JF  - Aerospace Science and Technology
N2  - Operational Modal Analysis (OMA) is a promising candidate for flutter testing and Structural Health Monitoring (SHM) of aircraft wings that are passively excited by wind loads. However, no studies have been published where OMA is tested in transonic flows, which is the dominant condition for large civil aircraft and is characterized by complex and unique aerodynamic phenomena. We use data from the HIRENASD large-scale wind tunnel experiment to automatically extract modal parameters from an ambiently excited wing operated in the transonic regime using two OMA methods: Stochastic Subspace Identification (SSI) and Frequency Domain Decomposition (FDD). The system response is evaluated based on accelerometer measurements. The excitation is investigated from surface pressure measurements. The forcing function is shown to be non-white, non-stationary and contaminated by narrow-banded transonic disturbances. All these properties violate fundamental OMA assumptions about the forcing function. Despite this, all physical modes in the investigated frequency range were successfully identified, and in addition transonic pressure waves were identified as physical modes as well. The SSI method showed superior identification capabilities for the investigated case. The investigation shows that complex transonic flows can interfere with OMA. This can make existing approaches for modal tracking unsuitable for their application to aircraft wings operated in the transonic flight regime. Approaches to separate the true physical modes from the transonic disturbances are discussed.
Y1  - 2016
U6  - http://dx.doi.org/10.1016/j.ast.2015.11.032
SN  - 1270-9638
VL  - 49
SP  - 73
EP  - 79
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Neu, Eugen
A1  - Janser, Frank
A1  - Khatibi, Akbar A.
A1  - Orifici, Adrian C.
T1  - Operational modal analysis of a cantilever in a wind tunnel using optical fiber bragg grating sensors
T2  - 6th International Operational Modal Analysis Conference. IOMAC´15. 2015 May 12-14 Gijon - Spain
Y1  - 2015
U6  - http://dx.doi.org/10.13140/RG.2.1.3753.0324
ER  - 
TY  - JOUR
A1  - Neu, Eugen
A1  - Janser, Frank
A1  - Khatibi, Akbar A.
A1  - Orifici, Adrian C.
T1  - Fully Automated Operational Modal Analysis using multi-stage clustering
JF  - Mechanical Systems and Signal Processing
Y1  - 2017
U6  - http://dx.doi.org/10.1016/j.ymssp.2016.07.031
SN  - 0888-3270
VL  - Vol. 84, Part A
SP  - 308
EP  - 323
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Neu, Eugen
A1  - Janser, Frank
A1  - Khatibi, Akbar A.
A1  - Orifici, Adrian C.
T1  - Automated modal parameter-based anomaly detection under varying wind excitation
JF  - Structural Health Monitoring
N2  - Wind-induced operational variability is one of the major challenges for structural health monitoring of slender engineering structures like aircraft wings or wind turbine blades. Damage sensitive features often show an even bigger sensitivity to operational variability. In this study a composite cantilever was subjected to multiple mass configurations, velocities and angles of attack in a controlled wind tunnel environment. A small-scale impact damage was introduced to the specimen and the structural response measurements were repeated. The proposed damage detection methodology is based on automated operational modal analysis. A novel baseline preparation procedure is described that reduces the amount of user interaction to the provision of a single consistency threshold. The procedure starts with an indeterminate number of operational modal analysis identifications from a large number of datasets and returns a complete baseline matrix of natural frequencies and damping ratios that is suitable for subsequent anomaly detection. Mahalanobis distance-based anomaly detection is then applied to successfully detect the damage under varying severities of operational variability and with various degrees of knowledge about the present operational conditions. The damage detection capabilities of the proposed methodology were found to be excellent under varying velocities and angles of attack. Damage detection was less successful under joint mass and wind variability but could be significantly improved through the provision of the currently encountered operational conditions.
Y1  - 2016
U6  - http://dx.doi.org/10.1177/1475921716665803
SN  - 1475-9217
VL  - 15
IS  - 6
SP  - 1
EP  - 20
PB  - Sage
CY  - London
ER  - 
TY  - CHAP
A1  - Neu, Eugen
A1  - Janser, Frank
A1  - Khatibi, Akbar A.
A1  - Orifici, Adrian C.
T1  - In-flight vibration-based structural health monitoring of aircraft wings
T2  - 30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea
N2  - This work presents a methodology for automated
damage-sensitive feature extraction and anomaly
detection under multivariate operational variability
for in-flight assessment of wings. The
method uses a passive excitation approach, i. e.
without the need for artificial actuation. The
modal system properties (natural frequencies and
damping ratios) are used as damage-sensitive
features. Special emphasis is placed on the use
of Fiber Bragg Grating (FBG) sensing technology
and the consideration of Operational and
Environmental Variability (OEV). Measurements
from a wind tunnel investigation with a composite
cantilever equipped with FBG and piezoelectric
sensors are used to successfully detect an impact
damage. In addition, the feasibility of damage
localisation and severity estimation is evaluated
based on the coupling found between damageand
OEV-induced feature changes.
Y1  - 2016
ER  - 
TY  - CHAP
A1  - Niedermeier, H.
A1  - Clemens, J.
A1  - Kowalski, Julia
A1  - Macht, S.
A1  - Heinen, D.
A1  - Hoffmann, R.
A1  - Linder, Peter
T1  - Navigation system for a research ice probe for antarctic glaciers
T2  - IEEE/ION Position, Location and Navigation Symposium (PLANS) ; 5-8 May 2014, Monterey, Calif.
Y1  - 2014
SN  - 978-1-4799-3319-8
SP  - 959
EP  - 975
PB  - IEEE
CY  - Piscataway, NJ
ER  - 
TY  - PAT
A1  - Nonhoff, Gottfried
A1  - Wahle, Michael
T1  - Anordnung zur Dämpfung von Schwingungen an Bauwerken und Bauteilen : Offenlegungsschrift / Europäische Patentschrift
T1  - Arrangement for damping vibrations of structures or parts thereof : patent of invention
Y1  - 1990
PB  - Deutsches Patent- und Markenamt / Europäisches Patentamt
CY  - München / Den Hague
ER  - 
TY  - CHAP
A1  - Nowack, N.
A1  - Röth, Thilo
A1  - Bührig-Polaczek, A.
A1  - Klaus, G.
ED  - Hirsch, Jürgen
T1  - Advanced Sheet Metal Components Reinforced by Light Metal Cast Structures
T2  - Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]
Y1  - 2008
SN  - 978-3-527-32367-8
IS  - 2
SP  - 2374
EP  - 2381
ER  - 
TY  - CHAP
A1  - Ohndorf, Andreas
A1  - Dachwald, Bernd
A1  - Seboldt, Wolfgang
A1  - Schartner, Karl-Heinz
T1  - Flight times to the heliopause using a combination of solar and radioisotope electric propulsion
T2  - 32nd International Electric Propulsion Conference
N2  - We investigate the interplanetary flight of a low-thrust space probe to the heliopause,located at a distance of about 200 AU from the Sun. Our goal was to reach this distance within the 25 years postulated by ESA for such a mission (which is less ambitious than the 15-year goal set by NASA). Contrary to solar sail concepts and combinations of allistic and electrically propelled flight legs, we have investigated whether the set flight time limit could also be kept with a combination of solar-electric propulsion and a second, RTG-powered upper stage. The used ion engine type was the RIT-22 for the first stage and the RIT-10 for the second stage. Trajectory optimization was carried out with the low-thrust optimization program InTrance, which implements the method of Evolutionary Neurocontrol,using Artificial Neural Networks for spacecraft steering and Evolutionary Algorithms to optimize the Neural Networks’ parameter set. Based on a parameter space study, in which the number of thrust units, the unit’s specific impulse, and the relative size of the solar power generator were varied, we have chosen one configuration as reference. The transfer time of this reference configuration was 29.6 years and the fastest one, which is technically
more challenging, still required 28.3 years. As all flight times of this parameter study were longer than 25 years, we further shortened the transfer time by applying a launcher-provided hyperbolic excess energy up to 49 km2/s2. The resulting minimal flight time for the reference configuration was then 27.8 years. The following, more precise optimization to a launch with the European Ariane 5 ECA rocket reduced the transfer time to 27.5 years. This is the fastest mission design of our study that is flexible enough to allow a launch every
year. The inclusion of a fly-by at Jupiter finally resulted in a flight time of 23.8 years,which is below the set transfer-time limit. However, compared to the 27.5-year transfer,this mission design has a significantly reduced launch window and mission flexibility if the
escape direction is restricted to the heliosphere’s “nose".
KW  - low-thrust trajectory optimization
KW  - heliosphere
KW  - ion propulsion
Y1  - 2011
N1  - IEPC-2011-051
32nd International Electric Propulsion Conference,September 11–15, 2011
Wiesbaden, Germany
SP  - 1
EP  - 12
ER  - 
TY  - JOUR
A1  - Olaru, Alexandra Maria
A1  - Kowalski, Julia
A1  - Sethi, Vaishali
A1  - Blümich, Bernhard
T1  - Exchange relaxometry of flow at small Péclet numbers in a glass bead pack
JF  - Journal of Magnetic Resonance (JMR)
N2  - In this paper we consider low Péclet number flow in bead packs. A series of relaxation exchange experiments has been conducted and evaluated by ILT analysis. In the resulting correlation maps, we observed a collapse of the signal and a translation towards smaller relaxation times with increasing flow rates, as well as a signal tilt with respect to the diagonal. In the discussion of the phenomena we present a mathematical theory for relaxation exchange experiments that considers both diffusive and advective transport. We perform simulations based on this theory and discuss them with respect to the conducted experiments.
KW  - NMR exchange relaxometry
KW  - Low-field NMR
Y1  - 2012
U6  - http://dx.doi.org/10.1016/j.jmr.2012.04.015
SN  - 1096-0856
VL  - 220
SP  - 32
EP  - 44
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Olaru, Alexandra Maria
A1  - Kowalski, Julia
A1  - Sethi, Vaishali
A1  - Blümich, Bernhard
T1  - Fluid Transport in Porous Media probed by Relaxation-Exchange NMR
T2  - 2011 Fall Meeting, AGU, San Francisco, Calif., 5-9 Dec.
Y1  - 2011
N1  - H12B-07; American Geophysical Union
ER  - 
TY  - CHAP
A1  - Otten, D.
A1  - Schmid, M.
A1  - Weber, Tobias
T1  - Advances In Sheet Metal-Forming: Reduction Of Tooling Cost By Methodical Optimization
T2  - Proceedings of SAMPE Europe Conference, Amiens , France
Y1  - 2015
ER  - 
TY  - CHAP
A1  - Otten, D.
A1  - Schmidt, M.
A1  - Weber, Tobias
T1  - Advances in Determination of Material Parameters for Functional Simulations Based on Process Simulations
T2  - SAMPE Europe Conference 16 Liege
Y1  - 2016
SN  - 978-1-5108-3800-0
SP  - 570
EP  - 577
ER  - 
TY  - JOUR
A1  - Otten, Dennis
A1  - Weber, Tobias
A1  - Arent, Jan-Christoph
T1  - Manufacturing Process Simulation – On Its Way to Industrial Application
JF  - International Journal of Aviation, Aeronautics, and Aerospace
N2  - Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview of the capabilities of MPS in the fields of sheet metal forming and prepreg autoclave manufacturing of composite parts summarizing the resulting benefits for tooling design and manufacturing engineering. The simulation technology is explained briefly in order to show several simplification and optimization techniques for developing industrialized simulation approaches. Small case studies provide examples of an efficient application on an industrial scale.
Y1  - 2018
U6  - http://dx.doi.org/10.15394/ijaaa.2018.1217
SN  - 2374-6793
VL  - 5
IS  - 2
PB  - Embry-Riddle Aeronautical University
CY  - Daytona Beach, Fla.
ER  - 
TY  - JOUR
A1  - Overduin, James
A1  - Blome, Hans-Joachim
A1  - Hoell, Josef
T1  - Wolfgang Priester: from the big bounce to the Lambda-dominated universe
JF  - Naturwissenschaften
Y1  - 2007
SN  - 0028-1042
VL  - 94
IS  - 6
SP  - 417
EP  - 429
ER  - 
TY  - CHAP
A1  - Pasligh, N.
A1  - Funke, D.
A1  - Röth, Thilo
A1  - Krack, R.
T1  - Leichtbau Quertrager als Stahlblech-Aluminiumdruckguss-Hybrid - Von der numerischen Berechnung bis zum realen Prototypen
T2  - VDI BERICHTE
Y1  - 2010
SN  - 978-3-18-092107-5
N1  - 15. Kongress SIMVEC Berechnung und Simulation im Fahrzeugbau, 
Baden-Baden, 16. und 17. November 2010
PB  - VDI Verlag
CY  - Düsseldorf
ER  - 
TY  - JOUR
A1  - Peeken, Heinz
A1  - Rosenkranz, Josef
A1  - Schelenz, R.
T1  - Berücksichtigung des Einflusses der Gleitlagergehäusesteifigkeit auf das dynamische Verhalten von Rotoren
JF  - Antriebstechnik : Organ der Forschungsvereinigung Antriebstechnik e.V.
Y1  - 1991
SN  - 0341-2652
VL  - 30
IS  - 9
SP  - 71
EP  - 75
ER  - 
TY  - CHAP
A1  - Peeken, Heinz
A1  - Troeder, Christoph
A1  - Schmidt, J.
A1  - Rosenkranz, Josef
T1  - Principles of machine noise reduction
T2  - Inter-noise 85 : proceedings ; 1985 international conference on noise control engineering ; Munich, Sept. 18 - 20, 1985. - (Schriftenreihe der Bundesanstalt für Arbeitsschutz : Tagungsbericht ; 39)
Y1  - 1985
SN  - 3-88314-417-7
SP  - 23
EP  - 36
PB  - Bundesanstalt für Arbeitsschutz [u.a.]
CY  - Dortmund [u.a.]
ER  - 
TY  - CHAP
A1  - Peloni, A.
A1  - Ceriotti, M.
A1  - Dachwald, Bernd
T1  - Preliminary trajectory design of a multiple NEO rendezvous mission through solar sailing
T2  - Proceedings of the International Astronautical Congress, IAC, Vol. 8, 2014
Y1  - 2015
SN  - 978-1-63439-986-9
SP  - 5352
EP  - 5366
PB  - Curran
CY  - Red Hook, NY
ER  - 
TY  - CHAP
A1  - Peloni, Alessandro
A1  - Ceriotti, Matteo
A1  - Dachwald, Bernd
T1  - Solar-Sailing Trajectory Design for Close-up NEA Observations Mission
T2  - 4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy
Y1  - 2015
N1  - IAA-PDC-15-P-19
ER  - 
TY  - JOUR
A1  - Peloni, Alessandro
A1  - Ceriotti, Matteo
A1  - Dachwald, Bernd
T1  - Solar-sail trajectory design for a multiple near-earth-asteroid rendezvous mission
JF  - Journal of Guidance, Control, and Dynamics
N2  - The scientific interest for near-Earth asteroids as well as the interest in potentially hazardous asteroids from the perspective of planetary defense led the space community to focus on near-Earth asteroid mission studies. A multiple near-Earth asteroid rendezvous mission with close-up observations of several objects can help to improve the characterization of these asteroids. This work explores the design of a solar-sail spacecraft for such a mission, focusing on the search of possible sequences of encounters and the trajectory optimization. This is done in two sequential steps: a sequence search by means of a simplified trajectory model and a set of heuristic rules based on astrodynamics, and a subsequent optimization phase. A shape-based approach for solar sailing has been developed and is used for the first phase. The effectiveness of the proposed approach is demonstrated through a fully optimized multiple near-Earth asteroid rendezvous mission. The results show that it is possible to visit five near-Earth asteroids within 10 years with near-term solar-sail technology.
Y1  - 2016
U6  - http://dx.doi.org/10.2514/1.G000470
SN  - 0731-5090
VL  - 39
IS  - 12
SP  - 2712
EP  - 2724
PB  - AIAA
CY  - Reston, Va.
ER  - 
TY  - JOUR
A1  - Peloni, Alessandro
A1  - Dachwald, Bernd
A1  - Ceriotti, Matteo
T1  - Multiple near-earth asteroid rendezvous mission: Solar-sailing options
JF  - Advances in Space Research
Y1  - 2017
U6  - http://dx.doi.org/10.1016/j.asr.2017.10.017
SN  - 0273-1177
IS  - In Press, Corrected Proof
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Peloni, Alessandro
A1  - Dachwald, Bernd
A1  - Ceriotti, Matteo
T1  - Multiple NEA rendezvous mission: Solar sailing options
T2  - Fourth International Symposium on Solar Sailing
N2  - The scientific interest in near-Earth asteroids (NEAs) and the classification of some of those as potentially hazardous asteroid for the Earth stipulated the interest in NEA exploration. Close-up observations of these objects will increase drastically our knowledge about the overall NEA population. For this reason, a multiple NEA rendezvous mission through solar sailing is investigated, taking advantage of the propellantless nature of this groundbreaking propulsion technology. Considering a spacecraft based on the DLR/ESA Gossamer technology, this work focuses on the search of possible sequences of NEA encounters. The effectiveness of this approach is demonstrated through a number of fully-optimized trajectories. The results show that it is possible to visit five NEAs within 10 years with near-term solar-sail technology. Moreover, a study on a reduced NEA database demonstrates the reliability of the approach used, showing that 58% of the sequences found with an approximated trajectory model can be converted into real solar-sail trajectories. Lastly, this second study shows the effectiveness of the proposed automatic optimization algorithm, which is able to find solutions for a large number of mission scenarios without any input required from the user.
KW  - Multiphase
KW  - Trajectory Optimization
KW  - Automated Optimization
KW  - Gossamer
KW  - Sequence-Search
Y1  - 2017
N1  - Fourth International Symposium on Solar Sailing (ISSS 2017), Kyoto, Japan, 17-20 Jan 2017.
http://www.jsforum.or.jp/ISSS2017/
SP  - 1
EP  - 11
ER  - 
TY  - JOUR
A1  - Peterson, Leif Arne
A1  - Röth, Thilo
A1  - Uibel, Thomas
T1  - Einsatz von Holzwerkstoffen in Fahrzeugstrukturen
JF  - Bauen mit Holz
Y1  - 2017
SN  - 0005-6545
N1  - gedruckt in der Bereichsbibliothek Bayernallee
IS  - 3
SP  - 32
EP  - 38
PB  - Bruderverlag
CY  - Köln
ER  - 
TY  - CHAP
A1  - Peterson, Leif Arne
A1  - Röth, Thilo
A1  - Uibel, Thomas
ED  - Uibel, Thormas
ED  - Peterson, Leif Arne
ED  - Baumann, Marcus
T1  - Holzwerkstoffe in Karosseriestrukturen
T2  - Tagungsband Aachener Holzbautagung 2017
Y1  - 2017
SN  - 2197-4489
SP  - 34
EP  - 45
ER  - 
TY  - CHAP
A1  - Pflug, J.
A1  - Wahle, Michael
ED  - Bürger, Gudrun
T1  - Auslegung der CFK-Sandwich-Rumpfstruktur eines Hubschraubers mit der Methode der Finiten Elemente
T2  - Basistechnologien für neue Herausforderungen in der Luft- und Raumfahrt : DGLR-Jahrestagung / Deutscher Luft- und Raumfahrt-Kongress 1994, Erlangen, 04.- 07. Oktober 1994. - (Jahrbuch der Deutschen Gesellschaft für Luft- und Raumfahrt ; 1994,3)
Y1  - 1994
SP  - 1135
EP  - 1144
PB  - DGLR
CY  - Bonn
ER  - 
TY  - JOUR
A1  - Pichler, A.
A1  - George, A.
A1  - Seiler, F.
A1  - Srulijes, J.
A1  - Havermann, Marc
T1  - Doppler Picture Velocimetry (DPV) applied to hypersonics
JF  - Shock Waves [Elektronische Ressource] : 26th International Symposium on Shock Waves, Volume 1 / edited by Klaus Hannemann, Friedrich Seiler
Y1  - 2009
SN  - 978-3-540-85168-4
N1  - International Symposium on Shock Waves ; (26 ; 2007.07.15-20 ; Göttingen) ; ISSW ; (26 ; 2007.07.15-20 ; Göttingen)
SP  - 503
EP  - 508
PB  - Springer
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Pielen, Michael
A1  - Röth, Thilo
A1  - Flatten, T.
ED  - Proff, H.
T1  - Erfolgsfaktoren künftiger Geschäftsmodelle von urbanen, geteilten Mobilitätsdienstleistungen
T2  - Mobilität und digitale Transformation.  (9. Wissenschaftsforum Mobilität. Tagungsband)
N2  - Digitalisierung bezeichnet die Nutzung großer Datenmengen, die zu einer umfassenden Vernetzung aller Bereiche der Wirtschaft und Gesellschaft führen wird (BMWi, 2015 und ähnlich Köhler/Wollschläger, 2014: 79). Sie umfasst die Erhebung von analogen Informationen („Big Data“ in einem engen Sinne; z.B. O´Leary, 2013), ihre Speicherung in einem digitaltechnischen System (lokale Speicherung oder „Cloud Computing“ durch die Weiterentwickelung des Internets; z.B. Hashem et al., 2015: 101), die Analyse und Interpretation sowie den Transfer in andere Systeme („Internet der Dinge“ bzw. „Internet of Things“; z.B. Ashton, 2009).
Y1  - 2018
SN  - 978-3-658-20779-3
U6  - http://dx.doi.org/10.1007/978-3-658-20779-3_2
SP  - 435
EP  - 448
PB  - Springer Gabler
CY  - Wiesbaden
ER  - 
TY  - CHAP
A1  - Pirovano, Laura
A1  - Seefeldt, Patric
A1  - Dachwald, Bernd
A1  - Noomen, Ron
T1  - Attitude and Orbital Dynamics Modeling for an Uncontrolled Solar-Sail Experiment in Low-Earth Orbit
T2  - 25th International Symposium on Spaceflight Dynamics, 2015, Munich, Germany
Y1  - 2015
ER  - 
TY  - CHAP
A1  - Pirovano, Laura
A1  - Seefeldt, Patric
A1  - Dachwald, Bernd
A1  - Noomen, Ron
T1  - Attitude and orbital modeling of an uncontrolled solar-sail experiment in low-Earth orbit
T2  - 25th International Symposium on Space Flight Dynamics ISSFD
N2  - Gossamer-1 is the first project of the three-step Gossamer roadmap, the purpose of which is to develop, prove and demonstrate that solar-sail technology is a safe and reliable propulsion technique for long-lasting and high-energy missions. This paper firstly presents the structural analysis performed on the sail to understand its elastic behavior. The results are then used in attitude and orbital simulations. The model considers the main forces and torques that a satellite experiences in low-Earth orbit coupled with the sail deformation. Doing the simulations for varying initial conditions in attitude and rotation rate, the results show initial states to avoid and maximum rotation rates reached for correct and faulty deployment of the sail. Lastly comparisons with the classic flat sail model are carried out to test the hypothesis that the elastic behavior does play a role in the attitude and orbital behavior of the sail
KW  - Solar sail
KW  - Gossamer structures
KW  - Attitude dynamics
KW  - Orbital dynamics
Y1  - 2015
N1  - 25th International Symposium on Space Flight Dynamics ISSFD
October 19 – 23, 2015, Munich, Germany
https://issfd.org/2015/
SP  - 1
EP  - 15
ER  - 
TY  - PAT
A1  - Pischinger, Martin
A1  - Esch, Thomas
A1  - Duesmann, Klaus
T1  - Elektromagnetischer Aktuator mit gelenkig abgestützter Rückstellfeder
N2  - Die Erfindung betrifft einen elektromagnetischen Aktuator zur Betätigung eines Stellgliedes (7) mit wenigstens einem gesteuert bestrombaren Elektromagneten (1, 2) und einem mit dem Stellglied (7) in Wirkverbindung stehenden Anker (5), der bei Bestromung des Elektromagneten (1, 2) gegen die Kraft wenigstens einer an einem Gehäuse (12) abgestützten Rückstellfeder (10) an der Polfläche (3, 4) des Elektromagneten (1, 2) zur Anlage kommt, und daß zumindest der Anker (5) über eine sphärische Gelenkanordnung (11) auf der Rückstellfeder (10) abgestützt ist.
Y1  - 2023
N1  - Patent DE000019822907B4 2006.07.27
ER  - 
TY  - CHAP
A1  - Plescher, Engelbert
A1  - Mathiak, Gerhard
A1  - Willnecker, Rainer
T1  - Technical aspects of liquid diffusion model experiments
T2  - 55th International Astronautical Congress : October 4 - 8, 2004, Vancouver, Canada / International Astronautical Federation. Bd. 8. IAC-04-J.5.04
Y1  - 2005
SP  - 5019
EP  - 5025
PB  - International Astronautical Federation
CY  - Paris
ER  - 
TY  - GEN
A1  - Polaczek, Christa
T1  - Kofaser - Kategorien und differentielle Algebren
Y1  - 1983
N1  - Bonn, Univ., Diplomarb., 1983
PB  - Math. Inst. der Univ.
CY  - Bonn
ER  - 
TY  - THES
A1  - Polaczek, Christa
T1  - Automatische 3-dimensionale FEM-Netzgenerierung für die Formfüll- und Erstarrungssimulation. - (Fortschrittberichte VDI : Reihe 20, Rechnerunterstützte Verfahren ; 182)
Y1  - 1995
SN  - 3-18-318220-3
N1  - Zugl.: Aachen, Techn. Hochsch., Diss., 1994
IS  - Als Ms. gedr.
PB  - VDI-Verl.
CY  - Düsseldorf
ER  - 
TY  - JOUR
A1  - Polaczek, Christa
A1  - Henn, Gudrun
T1  - Gute Vorkenntnisse verkürzen die Studienzeit
JF  - Mathematikinformation : eine Zeitschrift von Begabtenförderung Mathematik e.V.
Y1  - 2008
SN  - 1612-9156
VL  - 2008
IS  - 49
SP  - 46
EP  - 50
PB  - Begabtenförderung Mathematik
CY  - Neubiberg
ER  - 
TY  - CHAP
A1  - Quitter, Julius
A1  - Marino, Matthew
A1  - Bauschat, J.-Michael
T1  - Highly Non-Planar Aircraft Configurations: Estimation of Flight Mechanical Derivatives Using Low-Order Methods
T2  - Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany
Y1  - 2019
ER  - 
TY  - PAT
A1  - Rainer, Nähle
A1  - Röstel, Reinhard
A1  - Wahle, Michael
T1  - Lagerungssystem in einem Raumfahrzeug : Patentschrift
T1  - Storage system for use inside a spacecraft has damping elements consisting of at least one permanent magnet and vortex flow plate : patent of invention
Y1  - 2006
PB  - Deutsches Patent- und Markenamt
CY  - München
ER  - 
TY  - JOUR
A1  - Recker, Elmar
A1  - Bosschaerts, Walter
A1  - Wagemakers, Rolf
A1  - Hendrick, Patrick
A1  - Funke, Harald
A1  - Börner, Sebastian
T1  - Experimental study of a round jet in cross-flow at low momentum ratio
JF  - 15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1
Y1  - 2010
SP  - 1
EP  - 13
ER  - 
TY  - CHAP
A1  - Reimer, Lars
A1  - Braun, Carsten
A1  - Ballmann, Josef
T1  - Computational study of the aeroelastic equilibrium configuration of a swept wind tunnel wing model in subsonic flow
T2  - High performance computing in science and engineering '06. Transactions of the High Performance Computing Center Stuttgart (HLRS) 2006 /  Wolfgang E. Nagel ... Eds.
N2  - In the Collaborative Research Center SFB 401 at RWTH Aachen University, the numerical aeroelastic method SOFIA for direct numerical aeroelastic simulation is being progressively developed. Numerical results obtained by applying SOFIA were compared with measured data of static and dynamic aeroelastic wind tunnel tests for an elastic swept wing in subsonic flow.
Y1  - 2007
SN  - 978-3-540-36165-7
SP  - 421
EP  - 434
PB  - Springer
CY  - Berlin [u.a.]
ER  - 
TY  - CHAP
A1  - Reimer, Lars
A1  - Braun, Carsten
A1  - Ballmann, Josef
T1  - Analysis of the static and dynamic aero-structural response of an elastic swept wing model by direct aeroelastic simulation
T2  - ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences
Y1  - 2006
SN  - 0-9533991-7-6
SP  - Paper No. 2006-10.3.3
PB  - Optimage
CY  - Edinburgh
ER  - 
TY  - CHAP
A1  - Reimer, Lars
A1  - Braun, Carsten
A1  - Chen, B.-H.
A1  - Ballmann, Josef
T1  - Computational aeroelastic analysis and design of the HIRENASD wind tunnel wing model and tests
T2  - Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics : June 18 - 21, 2007, Stockholm, Sweden
Y1  - 2007
PB  - KTH
CY  - Stockholm
ER  - 
TY  - CHAP
A1  - Reimer, Lars
A1  - Braun, Carsten
A1  - Wellmer, Georg
A1  - Behr, Marek
A1  - Ballmann, Josef
T1  - Development of a modular method for computational aero-structural analysis of aircraft
T2  - Summary of flow modulation and fluid-structure interaction findings. Results of the Collaborative Research Center SFB 401 at the RWTH Aachen University, Aachen, Germany, 1997-2008 / ed.: Wolfgang Schröder. Notes on numerical fluid mechanics and multidisciplinary design. Vol. 109
Y1  - 2010
SN  - 978-3-642-04087-0
SP  - 205
EP  - 238
PB  - Springer
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Reimer, Lars
A1  - Wellmer, Georg
A1  - Braun, Carsten
A1  - Ballmann, Josef
T1  - Computational methods for aero-structural analysis and optimisation of aircrafts based on reduced-order structural models
T2  - MEGADESIGN and MegaOpt - German initiatives for aerodynamic simulation and optimization in aircraft design. Results of the closing symposium of the MEGADESIGN and MegaOpt projects, Braunschweig, Germany, 23 - 24 May, 2007 / Norbert Kroll ... (Eds.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 107
N2  - In this part of the MEGADESIGN project, aeroelastic effects are introduced into the aerodynamic analysis of aircrafts by coupling DLR’s flow solvers TAU and FLOWer to a Timoshenko-beam solver. The emerging aeroelastic solvers and a method for the automatic identification of Timoshenko-beam models for wing-box structures were integrated into a simulation environment enabling the combined optimisation of aerodynamic wing shape and structure.
Y1  - 2009
SN  - 978-3-642-04092-4
SP  - 135
EP  - 150
PB  - Springer
CY  - Berlin
ER  - 
TY  - RPRT
A1  - Reimer, Lars
A1  - Wellmer, Georg
A1  - Braun, Carsten
A1  - Ballmann, Josef
T1  - Aerodynamische Simulation und Optimierung in der Flugzeugentwicklung. Teilvorhabenbezeichnung: Aerodynamische Optimierung unter Berücksichtigung von Struktureigenschaften auf der Basis reduzierter Strukturmodelle, Verbundvorhaben MEGADESIGN. Schlussbericht. Berichtszeitraum: 01.06.2003-31.05.2007. BMBF-Forschungsbericht
Y1  - 2007
ER  - 
TY  - CHAP
A1  - Rings, René
A1  - Ludowicy, Jonas
A1  - Finger, Felix
A1  - Braun, Carsten
A1  - Bil, Cees
T1  - Sensitivity Analysis of General Aviation Aircraft with Parallel Hybrid-Electric Propulsion Systems
T2  - Asia Pacific International Symposium on Aerospace Technology. APISAT 2019
Y1  - 2019
ER  - 
TY  - JOUR
A1  - Robinson, A. E.
A1  - Funke, Harald
A1  - Hendrick, P.
T1  - Design and Testing of a Micromix Combustor With Recuperative Wall Cooling for a Hydrogen Fueled µ-Scale Gas Turbine
JF  - Journal of engineering for gas turbines and power
Y1  - 2011
SN  - 1528-8919
VL  - 133
IS  - 8
PB  - ASME
CY  - New York
ER  - 
TY  - JOUR
A1  - Robinson, A. E.
A1  - Funke, Harald
A1  - Hendrick, P.
A1  - Recker, E.
A1  - Peirs, J.
T1  - Development of a hydrogen fuelled 1 kW ultra micro gas turbine with special respect to designing, testing and mapping of the µ-scale combustor
JF  - IEEE International Conference on Sustainable Energy Technologies, 2008 : ICSET 2008 ; Singapore, 24 - 27 Nov. 2008.
Y1  - 2008
SN  - 978-1-4244-1887-9
SP  - 656
EP  - 660
PB  - IEEE
CY  - Piscataway, NJ
ER  - 
TY  - JOUR
A1  - Robinson, A. E.
A1  - Funke, Harald
A1  - Wagemakers, R.
A1  - Grossen, J.
A1  - Bosschaerts, W.
A1  - Hendrick, P.
T1  - Numerical and Experimental Investigation of a Micromix Combustor for a Hydrogen Fuelled μ-Scale Gas Turbine
JF  - Proceedings of the ASME Turbo Expo 2009 : : presented at the 2009 ASME Turbo Expo, June 8 - 12, 2009, Orlando, Florida, USA / sponsored by the International Gas Turbine Institute
Y1  - 2009
SN  - 9780791848869
N1  - GT2009-60061
SP  - 253
EP  - 262
PB  - ASME
CY  - New York, NY
ER  - 
TY  - JOUR
A1  - Robinson, A. E.
A1  - Rönna, Uwe
A1  - Funke, Harald
T1  - Testing of a 10 kW diffusive micro-mix combustor for hydrogen-fuelled micro-scale gas turbines
JF  - International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications <7, 2007, Freiburg, Breisgau>  ; PowerMEMS ; 7
Y1  - 2007
SP  - 225
EP  - 228
ER  - 
TY  - CHAP
A1  - Roosen, Petra
A1  - Feyerl, Günter
T1  - Gender-specific perception and utilization of personal use vehicles
T2  - FISITA World Automotive Congress 2014 : Maastricht, The Netherlands, 2 - 6 June / [organised by the International Federation of Automotive Engineering Societies (FISITA) ...]. Bd. 1
Y1  - 2015
SN  - 978-1-5108-0209-4
SP  - 418
EP  - 425
PB  - Curran
CY  - Red Hook, NY
ER  - 
TY  - PAT
A1  - Rosenkranz, Josef
T1  - Überwachungsvorrichtung für eine Auswuchtmaschine : Patentschrift
Y1  - 2001
PB  - Deutsches Patent- und Markenamt
CY  - München
ER  - 
TY  - CHAP
A1  - Rosenkranz, Josef
T1  - Verbesserung der Laufruhe des Verbrennungsmotors durch abgestimmte qualitätssteigernde Maßnahmen beim Auswuchten des Kurbeltriebs
T2  - Antriebstechnisches Kolloquium '93 / Industrieentwicklungen und Forschungsergebnisse für die Maschinenüberwachung und die Konstruktion in der Antriebstechnik. - (Reihe IME-Leitfaden)
Y1  - 1993
SN  - 3-8249-0139-0
SP  - 176
EP  - 199
PB  - Verl. TÜV Rheinland
CY  - Köln
ER  - 
TY  - THES
A1  - Rosenkranz, Josef
T1  - Die Gleitlagergehäusesteifigkeit als modaler Parameter für Rotorsysteme
Y1  - 1989
N1  - Aachen, Techn. Hochsch., Diss., 1989
CY  - Aachen
ER  - 
TY  - RPRT
A1  - Rosenkranz, Josef
T1  - Berücksichtigung des Einflusses von Gleitlagergehäusen auf das dynamische Verhalten von Rotoren : Abschlußbericht : Forschungsvorhaben Nr. 128 "Gleitlagergehäusesteifigkeit" ; Berichtszeitraum 1985-1988. - (Forschungsheft / Forschungsvereinigung Antriebstechnik e.V. ; 303)
Y1  - 1989
N1  - Förderkennzeichen BMWi/AIF-Nr. 6371
PB  - FVA
CY  - Frankfurt am Main
ER  - 
TY  - CHAP
A1  - Rupp, Matthias
A1  - Kuperjans, Isabel
A1  - Schulze, Sven
ED  - Berns, Karsten
T1  - Energetische und ökologische Bewertung hybrider Antriebe im städtischen Busverkehr
T2  - Commercial vehicle technology 2016 : proceedings of the 4th Commercial Vehicle Technology Symposium (CVT 2016), March 8-10, 2016, University of Kaiserslautern, Kaiserslautern, Germany
N2  - In Anbetracht weltweit zunehmend strengerer klimapolitischer
Ziele steigt auch der Druck für Nutzfahrzeughersteller, effizientere und umweltfreundlichere
Technologien zu entwickeln. Den Blick bei der Bewertung dieser
ausschließlich auf die Fahrzeugnutzung zu richten, ist längst nicht mehr zufriedenstellend.
Im Rahmen dieser Analyse wird ein gegenwärtig auf dem Markt erwerblicher
und in deutschen Städten bereits seit Jahren betriebener Hybridbus
energetisch und ökologisch mit einem konventionell angetriebenen, nahezu baugleichen
Modell entlang des Lebensweges bewertet.
Nach Definition von Ziel und Untersuchungsrahmen wird ein Überblick auf bereits
durchgeführte Lebenszyklusanalysen zu Hybridbussen im Stadtverkehr gegeben
und Schlussfolgerungen für die anschließende Analyse abgeleitet. Diese
wird im Rahmen einer energetischen und ökologischen Bewertung beider Produktsysteme
anhand der Parameter "Primärenergieeinsatz" und "CO2äq Emissionen"
praktiziert. Der Fahrzeugrumpf beider Fahrzeuge des gleichen Modells
wird dabei als einheitlich angenommen, sodass bei dem Vergleich der Herstellung
vereinfacht nur die sich unterscheidenden Komponenten des Antriebstranges
berücksichtigt werden. Die Resultate der Wirkungsabschätzung werden als
Differenz des Hybridbusses gegenüber dem Referenzfahrzeug über die einzelnen
Lebenszyklusphasen dargestellt. Schließlich werden Prognosen getroffen, ab
welcher Strecke die bei der Herstellung erzeugten höheren CO2äq Emissionen
des Hybridantriebstranges gegenüber dem Referenzmodell ausgeglichen werden.
Y1  - 2016
SP  - 227
EP  - 237
PB  - Shaker
CY  - Aachen
ER  - 
TY  - BOOK
A1  - Röth, Thilo
T1  - Konstruktive und versuchstechnische Entwicklungswerkzeuge zur Gestaltung "fußgängerfreundlicher" Pkw-Vorderwagen : Elektronische Ressource / vorgelegt von Thilo Röth
Y1  - 2001
N1  - Dissertation Universität Essen
CY  - Essen
ER  - 
TY  - CHAP
A1  - Röth, Thilo
A1  - Deutskens, Christoph
A1  - Kreisköther, Kai
A1  - Heimes, Heiner Hans
A1  - Schittny, Bastian
A1  - Ivanescu, Sebastian
A1  - Kleine Büning, Max
A1  - Reinders, Christian
A1  - Wessels, Saskia
A1  - Haunreiter, Andreas
A1  - Reisgen, Uwe
A1  - Thiele, Regina
A1  - Hameyer, Kay
A1  - Doncker, Rik W. de
A1  - Sauer, Uwe
A1  - Hoek, Hauke van
A1  - Hübner, Mareike
A1  - Hennen, Martin
A1  - Stolze, Thilo
A1  - Vetter, Andreas
A1  - Hagedorn, Jürgen
A1  - Müller, Dirk
A1  - Rewitz, Kai
A1  - Wesseling, Mark
A1  - Flieger, Björn
T1  - Entwicklung von elektrofahrzeugspezifischen Systemen
T2  - Elektromobilität
N2  - Die Batterie ist eine der absolut zentralen Komponenten des Elektrofahrzeugs. Die serielle Entwicklung und Produktion dieser Batterien und die Verbesserung der Leistungen wird entscheidend für den Erfolg der Elektromobilität sein. Die Batterie ist jedoch nicht das einzige elektrofahrzeugspezifische System, das neu entwickelt, umkonzipiert oder verbessert werden muss. So sind ebenso die Entwicklung der neuen Fahrzeugstruktur sowie des elektrifizierten Antriebsstranges Teil dieses Kapitels. Weiterhin wird ein Blick auf das bedeutende Thema des Thermomanagements geworfen.
Y1  - 2018
SN  - 978-3-662-53137-2
U6  - http://dx.doi.org/10.1007/978-3-662-53137-2_6
SP  - 279
EP  - 386
PB  - Springer Vieweg
CY  - Berlin, Heidelberg
ER  - 
TY  - CHAP
A1  - Röth, Thilo
A1  - Kampker, Achim
A1  - Reisgen, Uwe
A1  - Hameyer, Kay
A1  - De Doncker, R. W.
T1  - Entwicklung von elektrofahrzeugspezifischen Systemen
T2  - Elektromobilität : Grundlagen einer Zukunftstechnologie
N2  - Die Fahrzeugkarosserie bildet als größte funktionale und organisatorische Systemeinheit ein zentrales Kompetenzfeld der OEMs. Für den Fahrzeughersteller stellt der Karosserierohbau eine hohe Kernkompetenz sowohl in der Produktentwicklung als auch in der Produktion dar. Neue, innovative Karosseriebauweisen, bspw. aufgrund eines neuen Fahrzeugkonzeptes oder neuer Anforderungen, bedeuten für den OEM auch gleichzeitig die intensive Auseinandersetzung mit Kompetenzfokussierung bzw. Wertschöpfungsverlagerungen.
Y1  - 2013
SN  - 978-3-642-31986-0
SP  - 235
EP  - 336
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Röth, Thilo
A1  - Kern, Daniel
A1  - Kirchner, Karsten
A1  - Vietor, Thomas
T1  - Flexbody : Baukastensystem für Karosseriestrukturen / Kern, Daniel ; Röth, Thilo ; Kirchner, Karsten ; Vietor, Thomas
JF  - Mobiles : Fachzeitschrift für Konstrukteure. 35 (2009), H. 2009/2010
Y1  - 2009
SP  - 73
EP  - 75
PB  - Hochsch. für Angewandte Wiss.
CY  - Hamburg
ER  - 
TY  - JOUR
A1  - Röth, Thilo
A1  - Nowack, N.
A1  - Baumeister, E.
T1  - Numerische Lösungsansätze zur Auslegung von Stahl-Leichtmetall-Hybriden aus Verbundguss für zukünftige Fahrzeugstrukturen / Nowack, N. ; Röth, T. ; Baumeister, E.
JF  - Berechnung und Simulation im Fahrzeugbau. Bd. 1 : Tagung Würzburg, 27. und 28. September 2006 = Numerical analysis and simulation in vehicle engineering / VDI-Gesellschaft Fahrzeug- und Verkehrstechnik
Y1  - 2006
SN  - 3-18-091967-1
N1  - VDI-Berichte ; 1967
SP  - 363
EP  - 368
PB  - VDI-Verl.
CY  - Düsseldorf
ER  - 
TY  - JOUR
A1  - Röth, Thilo
A1  - Nowack, Niels
A1  - Oberschelp, Christian
A1  - Lao, Bin
T1  - Gute Perspektiven für Stahl-Alumnium-Hybride im Automotivebereich / Nowack, Niels ; Oberschelp, Christian ; Lao, Bin ; Klaus, Gerald ; Bührig-Polaczek, Andreas ; Röth, Thilo
JF  - Giesserei : die Zeitschrift für Technik, Innovation und Management. 96 (2009), H. 5
Y1  - 2009
SN  - 0016-9765
SP  - 110
EP  - 123
ER  - 
TY  - CHAP
A1  - Röth, Thilo
A1  - Pielen, Michael
T1  - Personal Public Vehicle – ein urbanes Fahrzeugkonzept für die „Shared Mobility“ der Zukunft
T2  - Karosseriebautage Hamburg 2018, 16. ATZ-Fachtagung
N2  - Die urbane Mobilität ist im Wandel und insbesondere neue innovative Geschäftsmodelle werden einen wesentlichen Teil zur Lösung von künftigen Mobilitätsbedürfnissen beitragen. Die sogenannte „Shared Mobility“ gilt aktuell neben der Elektrifizierung des Antriebes und autonomem Fahrzeugtechnologien als einer der wichtigsten Trendthemen in der Automobilindustrie. Neue Mobilitätsdienstleistungen verlangen dabei verstärkt auch neue Fahrzeugkonzepte.
Y1  - 2018
U6  - http://dx.doi.org/10.1007/978-3-658-22038-9_13
SP  - 189
EP  - 199
PB  - Springer Vieweg
CY  - Wiesbaden
ER  - 
TY  - JOUR
A1  - Röth, Thilo
A1  - Pielen, Michael
A1  - Wolff, Klaus
A1  - Lüdiger, Thomas
T1  - Urbane Fahrzeugkonzepte für die Shared Mobility
JF  - Automobiltechnische Zeitschrift - ATZ
N2  - Urbane Mobilitätskonzepte der Zukunft erfordern neue Unternehmensformen, idealerweise aus Old Economy und New Economy, sowie eine enge Anbindung an die gesellschaftsrelevante Zukunftsforschung. Für neue Fahrzeugkonzepte des Carsharing bedeutet dies, dass alle kostenverursachenden Faktoren erfasst und analysiert werden müssen. Die FH Aachen, share2drive und FEV geben einen Ausblick auf die zukünftige Fahrzeugklasse der Personal Public Vehicles als „Rolling Device“.
Y1  - 2018
U6  - http://dx.doi.org/10.1007/s35148-017-0176-8
SN  - 0001-2785
VL  - 120
IS  - 1
SP  - 18
EP  - 23
PB  - Springer Vieweg
CY  - Wiesbaden
ER  - 
TY  - JOUR
A1  - Röth, Thilo
A1  - Schreiber, Harold
T1  - CAKE (Computer Aided Kinematic Engineering) im Karrosseriebau und in der passiven Fahrzeugsicherheit / Schreiber , Harold ; Röth, Thilo
JF  - Mobiles. 2002/2003 (2003), H. 33
Y1  - 2003
N1  - in der Bibliothek Eupener Str. vorhanden
SP  - 65
EP  - 67
ER  - 
TY  - CHAP
A1  - Röth, Thilo
A1  - Stark, R.
T1  - Die Rolle der virtuellen Produktentstehung bei der Integration von Karosseriesystemen
T2  - Karosseriekongress Systemintegration in der Karosserietechnik : 17. und 18. März 2009 in Baden-Baden / Kongressleitung: Reiner Stark
Y1  - 2009
SN  - 978-3-9812624-4-5
N1  - Karosseriekongress ; (2009.03.17-18 : ; Baden-Baden)
PB  - VDI-Wissensforum
CY  - Düsseldorf
ER  - 
TY  - JOUR
A1  - Saffe, P.
A1  - Lodewiks, J.
A1  - Haas, H.-J.
A1  - Feigel, H.-J.
A1  - Ulrich, H.
A1  - Mauer, J.
A1  - Ortwig, H.
A1  - Dahmann, Peter
A1  - Rotthäuser, S.
A1  - Tao, J.
A1  - Ohlischläger, O.
A1  - Scholz, D.
A1  - Bergmann, M.
A1  - Anders, P.
T1  - Neues von ASB Antreiben – Steuern – Bewegen
JF  - Ölhydraulik und Pneumatik. Vol. 33 (1989), H. 7
Y1  - 1989
SN  - 0341-2660
SP  - 550
EP  - 572
ER  - 
TY  - PAT
A1  - Salber, Wolfgang
A1  - Pischinger, Martin
A1  - Esch, Thomas
A1  - Hagen, Jürgen
T1  - Kaltstartverfahren für eine drosselfreie Mehrzylinder-Kolbenbrennkraftmaschine
N2  - Die Erfindung betrifft ein Kaltstartverfahren für eine Mehrzylinder-Kolbenbrennkraftmaschine mit Anlasser und einer Motorsteuerung zur Ansteuerung von Kraftstoffeinspritzeinrichtungen, Zündung und voll variabel elektromagnetisch betätigbaren Gaswechselventilen an den einzelnen Zylindern, bei dem die Kurbelwelle über den Anlasser gedreht wird und zum Start für wenigstens einen Zylinder die dazugehörigen Gaswechselventile, die Kraftstoffeinspritzeinrichtung und die Zündung in einem vorgegebenen Taktzyklus angesteuert werden und zwar in den ersten Arbeitszyklen mit "Spätem Einlaß Öffnen".
Y1  - 2000
N1  - Patent DE000019830974B4 2005.11.03
ER  - 
TY  - JOUR
A1  - Schael, S.
A1  - Atanasyan, A.
A1  - Berdugo, J.
A1  - Bretz, T.
A1  - Czupalla, Markus
A1  - Dachwald, Bernd
A1  - Doetinchem, P. von
A1  - Duranti, M.
A1  - Gast, H.
A1  - Karpinski, W.
A1  - Kirn, T.
A1  - Lübelsmeyer, K.
A1  - Maña, C.
A1  - Marrocchesi, P.S.
A1  - Mertsch, P.
A1  - Moskalenko, I.V.
A1  - Schervan, T.
A1  - Schluse, M.
A1  - Schröder, K.-U.
A1  - Schultz von Dratzig, A.
A1  - Senatore, C.
A1  - Spies, L.
A1  - Wakely, S.P.
A1  - Wlochal, M.
A1  - Uglietti, D.
A1  - Zimmermann, J.
T1  - AMS-100: The next generation magnetic spectrometer in space – An international science platform for physics and astrophysics at Lagrange point 2
JF  - Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
Y1  - 2019
U6  - http://dx.doi.org/10.1016/j.nima.2019.162561
SN  - 0168-9002
VL  - 944
IS  - 162561
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Schartner, Karl-Heinz
A1  - Loeb, H. W.
A1  - Dachwald, Bernd
A1  - Ohndorf, Andreas
T1  - Perspectives of electric propulsion for outer planetary and deep space missions
T2  - European Planetary Science Congress 2009
N2  - Solar-electric propulsion (SEP) is superior with
respect to payload capacity, flight time and
flexible launch window to the conventional
interplanetary transfer method using chemical
propulsion combined with gravity assists. This fact
results from the large exhaust velocities of electric
low–thrust propulsion and is favourable also for
missions to the giant planets, Kuiper-belt objects
and even for a heliopause probe (IHP) as shown in
three studies by the authors funded by DLR. They
dealt with a lander for Europa and a sample return
mission from a mainbelt asteroid [1], with the
TANDEM mission [2]; the third recent one
investigates electric propulsion for the transfer to
the edge of the solar system.
All studies are based on triple-junction solar arrays,
on rf-ion thrusters of the qualified RIT-22 type and
they use the intelligent trajectory optimization
program InTrance [3].
Y1  - 2009
N1  - European Planetary Science Congress 2009, 13-18 September, Potsdam, Germany
SP  - 416
EP  - 416
ER  - 
TY  - CHAP
A1  - Schildt, P.
A1  - Braun, Carsten
A1  - Marcocca, P.
T1  - Flight testing the extra 330LE flying testbed
T2  - 48th Annual International Symposium of the Society of Flight Test Engineers 2017
Y1  - 2017
SN  - 978-151085387-4
N1  - 48th Annual International Symposium of the Society of Flight Test Engineers 2017, SFTE 2017; Destin; United States; 30 October 2017 through 2 November 2017
SP  - 349
EP  - 362
ER  - 
TY  - JOUR
A1  - Schildt, Ph.
A1  - Braun, Carsten
A1  - Marzocca, P.
T1  - Metric evaluating potentials of condition-monitoring approaches for hybrid electric aircraft propulsion systems
JF  - CEAS Aeronautical Journal
Y1  - 2019
U6  - http://dx.doi.org/10.1007/s13272-019-00411-3
SN  - 1869-5590
SP  - 1
EP  - 14
PB  - Springer
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Schildt, Philipp
A1  - Marzocca, Pier
A1  - Braun, Carsten
A1  - Dahmann, Peter
A1  - Keimer, Jona
T1  - Effects of atmospheric excitation on vibration based condition monitoring methods for hybrid-electric aircraft propulsion systems
T2  - AIAC 2018: 18th Australian International Aerospace Congress: HUMS - 11th Defence Science and Technology (DST) International Conference on Health and Usage Monitoring (HUMS 2019): ISSFD - 27th International Symposium on Space Flight Dynamics (ISSFD)
Y1  - 2019
SN  - 9781925627213
SP  - 923
EP  - 928
ER  - 
TY  - CHAP
A1  - Schirra, Julian
A1  - Bauschat, J.-Michael
A1  - Watmuff, J.H.
T1  - Accurate induced drag prediction for highly non-planar lifting systems
T2  - 19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia
N2  - The impact of wake model effects is investigated for two highly
non-planar lifting systems. Dependent on the geometrical
arrangement of the configuration, the wake model shape is found
to considerably affect the estimation. Particularly at higher angles
of attack, an accurate estimation based on the common linear wake
model approaches is involved.
Y1  - 2014
ER  - 
TY  - JOUR
A1  - Schirra, Julian
A1  - Bissonnette, William
A1  - Bramesfeld, Götz
T1  - Wake-model effects on induced drag prediction of staggered boxwings
JF  - Aerospace
Y1  - 2018
U6  - http://dx.doi.org/10.3390/aerospace5010014
SN  - 2226-4310
VL  - 5
IS  - 1
ER  -