TY - CHAP A1 - Šakić, Bogdan A1 - Milijaš, Aleksa A1 - Marinković, Marko A1 - Butenweg, Christoph A1 - Klinkel, Sven ED - Papadrakakis, Manolis ED - Fragiadakis, Michalis T1 - Influence of prior in-plane damage on the out-of-plane response of non-load bearing unreinforced masonry walls under seismic load T2 - 8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering N2 - Reinforced concrete frames with masonry infill walls are popular form of construction all over the world as well in seismic regions. While severe earthquakes can cause high level of damage of both reinforced concrete and masonry infills, earthquakes of lower to medium intensity some-times can cause significant level of damage of masonry infill walls. Especially important is the level of damage of face loaded infill masonry walls (out-of-plane direction) as out-of-plane load cannot only bring high level of damage to the wall, it can also be life-threating for the people near the wall. The response in out-of-plane direction directly depends on the prior in-plane damage, as previous investigation shown that it decreases resistance capacity of the in-fills. Behaviour of infill masonry walls with and without prior in-plane load is investigated in the experimental campaign and the results are presented in this paper. These results are later compared with analytical approaches for the out-of-plane resistance from the literature. Conclusions based on the experimental campaign on the influence of prior in-plane damage on the out-of-plane response of infill walls are compared with the conclusions from other authors who investigated the same problematic. KW - Earthquake Engineering KW - Unreinforced masonry walls KW - Out-of-plane load KW - In- plane damage KW - Out-of-plane failure Y1 - 2021 SN - 9786188507258 U6 - http://dx.doi.org/10.7712/120121.8527.18913 SN - 2623-3347 N1 - COMPDYN 2021 28-30 June 2021, Streamed from Athens, Greece SP - 808 EP - 828 PB - National Technical University of Athens CY - Athen ER - TY - CHAP A1 - Ögun, Celal Mohan A1 - Kling, Rainer A1 - Heuermann, Holger A1 - Gräser, Ulrich A1 - Schopp, Christoph T1 - Elektrodenlose quecksilberfreie Niederdrucklampen betrieben mit Mikrowellen T2 - Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband Y1 - 2014 PB - Nederlandse Stichting voor Verlichtingskunde CY - Ede ER - TY - CHAP A1 - Zähl, Philipp M. A1 - Theis, Sabine A1 - Wolf, Martin A1 - Köhler, Klemens ED - Chen, Jessie Y. C. ED - Fragomeni, Gino T1 - Teamwork in software development and what personality has to do with it - an overview T2 - Virtual, Augmented and Mixed Reality N2 - Due to the increasing complexity of software projects, software development is becoming more and more dependent on teams. The quality of this teamwork can vary depending on the team composition, as teams are always a combination of different skills and personality types. This paper aims to answer the question of how to describe a software development team and what influence the personality of the team members has on the team dynamics. For this purpose, a systematic literature review (n=48) and a literature search with the AI research assistant Elicit (n=20) were conducted. Result: A person’s personality significantly shapes his or her thinking and actions, which in turn influences his or her behavior in software development teams. It has been shown that team performance and satisfaction can be strongly influenced by personality. The quality of communication and the likelihood of conflict can also be attributed to personality. KW - Teamwork KW - Software KW - Personality KW - Performance KW - Elicit Y1 - 2023 SN - 978-3-031-35633-9 (Print) SN - 978-3-031-35634-6 (Online) U6 - http://dx.doi.org/10.1007/978-3-031-35634-6_10 N1 - Virtual, Augmented and Mixed Reality: 15th International Conference. VAMR 2023. Held as Part of the 25th HCI International Conference. HCII 2023. Copenhagen, Denmark. July 23–28, 2023. SP - 130 EP - 153 PB - Springer CY - Cham ER - TY - CHAP A1 - Zähl, Philipp M. A1 - Biewendt, Marcel A1 - Wolf, Martin A1 - Eggert, Mathias T1 - Requirements for Competence Developing Games in the Environment of SE Competence Development T2 - Angewandte Forschung in der Wirtschaftsinformatik 2022 N2 - Many of today’s factors make software development more and more complex, such as time pressure, new technologies, IT security risks, et cetera. Thus, a good preparation of current as well as future software developers in terms of a good software engineering education becomes progressively important. As current research shows, Competence Developing Games (CDGs) and Serious Games can offer a potential solution. This paper identifies the necessary requirements for CDGs to be conducive in principle, but especially in software engineering (SE) education. For this purpose, the current state of research was summarized in the context of a literature review. Afterwards, some of the identified requirements as well as some additional requirements were evaluated by a survey in terms of subjective relevance. KW - software engineering KW - requirements KW - competence developing games KW - systematic literature review Y1 - 2022 SN - 978-3-95545-409-8 U6 - http://dx.doi.org/10.30844/AKWI_2022_05 N1 - Tagungsband zur 35. Jahrestagung des Arbeitskreises Wirtschaftsinformatik an Hochschulen für Angewandte Wissenschaften im deutschsprachigen Raum (AKWI) vom 11.09. bis 13.09.2022, ausgerichtet von der Hochschule für Technik und Wirtschaft Berlin (HTW Berlin) und der Hochschule für Wirtschaft und Recht Berlin (HWR Berlin) SP - 73 EP - 88 PB - GITO CY - Berlin ER - TY - CHAP A1 - Zug, Sebastian A1 - Niemueller, Tim A1 - Hochgeschwender, Nico A1 - Seidensticker, Kai A1 - Seidel, Martin A1 - Friedrich, Tim A1 - Neumann, Tobias A1 - Karras, Ulrich A1 - Kraetzschmar, Gerhard K. A1 - Ferrein, Alexander T1 - An Integration Challenge to Bridge the Gap Among Industry-Inspired RoboCup Leagues T2 - RoboCup 2016: Robot World Cup XX. RoboCup 2016. Y1 - 2017 SN - 978-3-319-68792-6 U6 - http://dx.doi.org/10.1007/978-3-319-68792-6_13 N1 - Lecture Notes in Computer Science, LNCS, Vol 9776 SP - 157 EP - 168 PB - Springer CY - Cham ER - TY - CHAP A1 - Zischank, Wolfgang J. A1 - Kern, Alexander A1 - Frentzel, Ralf A1 - Heidler, Fridolin A1 - Seevers, M. T1 - Assessment of the lightning transient coupling to control cables interconnecting structures in large industrial facilities and power plants N2 - Large industrial facilities and power plants often require a huge number fo information and control cables between the differnet structures. These I&C-cables can be routed in reinforced concrete cable ducts or in isolated buried cable runs. KTA 2206 is the German lightning protection standard for nuclear power plants. During the last several years considerable effort has been made to revise this standard. Despite the well established principles and design guidelines for the construction of the lightning protection system, this standard puts special emphasis on the coupling of transient overvoltages to I&C-cables. KW - Blitzschutz KW - Elektromagnetische Kopplung KW - Überspannung KW - Kraftwerke KW - Industrieanlagen KW - Lightning KW - current distribution KW - electromagnetic coupling KW - overvoltages Y1 - 2000 ER - TY - CHAP A1 - Zischank, Wolfgang J. A1 - Heidler, Fridolin A1 - Wiesinger, J. A1 - Stimper, K. A1 - Kern, Alexander A1 - Seevers, M. T1 - Magnetic Fields and Induced Voltages inside LPZ 1 Measured at a 1:6 Scale Model Building N2 - Laborexperimente zu Blitzschutzzonen in Stahlbetongebäuden anhand eines Modells im Maßstab 1:6 N2 - For the application of the concept of Lightning Protection Zones (LPZ), the knowledge of the magnetic fields and induced voltages inside a structure is necessary. Laboratory experiments have been conducted at a downscaled model of a building (scale factor 1:6) to determine these electromagnetic quantities in case of a direct strike to the structure. The model (3 m x 2 m x 2 m) represented a small industrial building using the reinforcement of the concrete as electromagnetic shield. The magnetic fields and magnetic field derivatives were measured at several location inside the scaled model. Further, the voltages induced on three typical cable routes inside the model was determined. The influence of the lightning current waveshape, point-of-strike, bonding of the cable routes, and bridging of an expansion joint in the middle of the building on these quantities was studied. KW - Blitzschlag KW - Elektromagnetischer Schutzschild KW - Stahlbeton KW - Maßstabsgetreues Modell KW - Lightning KW - electromagnetic shielding KW - reinforced concrete KW - scaled model Y1 - 2004 ER - TY - CHAP A1 - Zischank, Wolfgang J. A1 - Heidler, Fridolin A1 - Kern, Alexander A1 - Metwally, I. A. A1 - Wiesinger, J. A1 - Seevers, M. T1 - Laboratory simulation of direct lightning strokes to a modelled building - measurement of magnetic fields and induced voltages N2 - In IEC 61312-2 equations for the assessment of the magnetic fields inside structures due to a direct lightning strike are given. These equations are based on computer simulations for shields consisting of a single-layer steel grid of a given mesh width. Real constructions, however, contain at least two layers of reinforcement steel grids. The objective of this study was to experimentally determine the additional shielding effectiveness of a second reinforcement layer compared to a single-layer grid. To this end, simulated structures were set up in the high current laboratory. The structures consisted of cubic cages of 2 m side length with one or with two reinforcement grids, respectively. The structures were exposed to direct lightning currents representing the variety of anticipated lightning current waveforms. The magnetic fields and their derivatives at several positions inside the structure as well as the voltage between “floor” and “roof” in the center were determined for different current injection points. From these data the improvement of the shielding caused by a second reinforcement layer is derived. KW - Direkter Blitzschlag KW - Elektromagnetischer Schutzschild KW - Magnetische Felder KW - Induzierte Spannungen KW - Stahlbetonkonstruktion KW - Lightning KW - electromagnetic shielding KW - magnetic field KW - reinforced concrete KW - induced voltage Y1 - 2002 ER - TY - CHAP A1 - Ziolko, Christoph A1 - Fricke, Barbara A1 - Anthrakidis, Anette A1 - Hoffschmidt, Bernhard A1 - Dillig, Marius A1 - Giese, Frank A1 - Schwarzbözl, Peter T1 - Ökobilanzielle Aspekte technologischer Entwicklungen des Solarturmkraftwerks T2 - Forschung und Entwicklung für solarthermische Kraftwerke : 14. Kölner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus Jülich der FH Aachen : Kurzfassungen der Vorträge und Poster Y1 - 2011 SP - 2 S. PB - DLR CY - Köln ER - TY - CHAP A1 - Ziolko, C. A1 - Schmitz, M. A1 - Sattler, Johannes, Christoph A1 - Khedim, Ahmed A1 - Hoffschmidt, Bernhard T1 - AlSol - the open volumetric receiver technology moves to Africa T2 - SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France Y1 - 2010 SP - 93 EP - 94 PB - Soc. OSC CY - Saint Maur ER - TY - CHAP A1 - Zingsheim, Jonas A1 - Grimmer, Timo A1 - Ortner, Marion A1 - Schmaderer, Christoph A1 - Hauser, Christine A1 - Kotliar, Konstantin ED - Staat, Manfred ED - Erni, Daniel T1 - Recognition of subjects with mild cognitive impairment (MCI) by the use of retinal arterial vessels. T2 - 3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen Y1 - 2019 SN - 978-3-940402-22-6 U6 - http://dx.doi.org/10.17185/duepublico/48750 SP - 36 EP - 37 PB - Universität Duisburg-Essen CY - Duisburg ER - TY - CHAP A1 - Ziller, Claudia A1 - Döring, Bernd ED - Carmeliet, J. ED - Hens, H. ED - Vermeir, G. T1 - Influence of the external dynamic wind pressure on the ventilation of double facades T2 - Research in building physics: proceedings of the Second International Conference on Building Physics : Leuven, Belgium, 14-18 September 2003 Y1 - 2003 SN - 9058095657, 9789058095657 SP - 527 EP - 533 PB - Taylor and Francis CY - Hoboken ER - TY - CHAP A1 - Ziegler, M. A1 - Schüller, R. A1 - Mottaghy, Darius T1 - Numerical simulation of energy consumption of artificial ground freezing applications subject to water seepage T1 - Simulation numérique de la consummation d´énergie des applications pour la congélation artificielle du sol soumise au flux de l´eau souterraine T2 - Proceedings of the 18th International Conference on Soil Mechanics and Geotechnical Engineering, Paris 2013 Y1 - 2013 SP - 2985 EP - 2988 ER - TY - CHAP A1 - Zang, Zhigang A1 - Hess, Holger A1 - Ringbeck, Thorsten A1 - Schwarte, Rudolf ED - Kamerman, Gary W. T1 - Phase-lock techniques using new correlation receivers for TOF-laser ranging T2 - Laser radar technology and applications VII : 3 - 4 April 2002, Orlando, USA. - (SPIE proceedings series ; 4723) Y1 - 2002 SN - 0-8194-4473-1 SN - 0038-7355 SN - 0361-0748 SN - 0277-786X N1 - Laser Radar Technology and Applications <7, 2002, Orlando, FL> SP - 112 EP - 120 PB - SPIE, International Society for Optical Engineering CY - Bellingham, Wash. ER - TY - CHAP A1 - Zahra, Mahdi A1 - Phani Srujan, Merige A1 - Caminos, Ricardo Alexander Chico A1 - Schmitz, Pascal A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José A1 - Schmitz, Mark A1 - Gielen, Hans A1 - Gedle, Yibekal A1 - Dersch, Jürgen T1 - Modeling the thermal behavior of solar salt in electrical resistance heaters for the application in PV-CSP hybrid power plants T2 - SOLARPACES 2020 N2 - Concentrated Solar Power (CSP) systems are able to store energy cost-effectively in their integrated thermal energy storage (TES). By intelligently combining Photovoltaics (PV) systems with CSP, a further cost reduction of solar power plants is expected, as well as an increase in dispatchability and flexibility of power generation. PV-powered Resistance Heaters (RH) can be deployed to raise the temperature of the molten salt hot storage from 385 °C up to 565 °C in a Parabolic Trough Collector (PTC) plant. To avoid freezing and decomposition of molten salt, the temperature distribution in the electrical resistance heater is investigated in the present study. For this purpose, a RH has been modeled and CFD simulations have been performed. The simulation results show that the hottest regions occur on the electric rod surface behind the last baffle. A technical optimization was performed by adjusting three parameters: Shell-baffle clearance, electric rod-baffle clearance and number of baffles. After the technical optimization was carried out, the temperature difference between the maximum temperature and the average outlet temperature of the salt is within the acceptable limits, thus critical salt decomposition has been avoided. Additionally, the CFD simulations results were analyzed and compared with results obtained with a one-dimensional model in Modelica. KW - Solar thermal technologies KW - Hybrid energy system KW - Concentrated solar power KW - Energy storage KW - Photovoltaics Y1 - 2022 SN - 978-0-7354-4195-8 U6 - http://dx.doi.org/10.1063/5.0086268 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - 26th International Conference on Concentrating Solar Power and Chemical Energy Systems 28 September–2 October 2020 Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Zahn, Helmut A1 - Berndt, Heinz A1 - Fehrenbach, P. ED - Hanson, Horst T1 - Synthese cyclischer Cystinpeptide mit Insulin A-und B-Kettensequenzen T2 - Peptides 1972 : proceedings of the Twelfth European Peptide Symposium, Reinhardsbrunn Castle, German Democratic Republic, September 1972 Y1 - 1973 SN - 0-7204-4132-3 SN - 0-444-10500-X SP - 101 EP - 102 PB - North-Holland Publ. [u.a.], CY - Amsterdam [u.a.] ER - TY - CHAP A1 - Yoshinobu, Tatsuo A1 - Miyamoto, Ko-Ichiro A1 - Wagner, Torsten A1 - Schöning, Michael Josef ED - Yamaguchi, Takami T1 - Miniaturized and high-speed chemical imaging systems T2 - Nano-Biomedical Engineering 2012. Proceedings of the Tohoku University Global Centre of Excellence Programme, Sakura Hall, Tohoku University, Sendai Japan, 5 – 6 March 2012 Y1 - 2012 U6 - http://dx.doi.org/10.1142/9781848169067_0045 SP - 386 EP - 395 PB - World Scientific CY - Singapur ER - TY - CHAP A1 - Yoshinobu, T. A1 - Schöning, Michael Josef A1 - Finger, F. A1 - Moritz, W. A1 - Iwasaki, H. T1 - Thin-film a-Si LAPS : Preparation and pH sensitivity T2 - Eurosensors XVII : the 17th European Conference on Solid-State Transducers ; University of Minho, Guimarães, Portugal, September 21 - 24, 2003 Y1 - 2003 SP - 88 EP - 89 ER - TY - CHAP A1 - Xu, Zhanping A1 - Schwarte, Rudolf A1 - Heinol, Horst-Guenther A1 - Buxbaum, Bernd A1 - Ringbeck, Thorsten ED - Cheung, Edmund H. M. T1 - Smart pixel : photonic mixer device (PMD) ; new system concept of a 3D-imaging camera-on-a-chip T2 - Proceedings : M2VIP '98; Nanjing, China, 10th - 12th September 1998 Y1 - 1998 SN - 962-442-129-3 N1 - International Conference on Mechatronics and Machine Vision in Practice <5, 1998, Nanking> ; M2VIP <5, 1998, Nanking> SP - 259 EP - 264 CY - Hong Kong ER - TY - CHAP A1 - Wuttke, Claudia A1 - Butenweg, Christoph A1 - Rosin, Julia A1 - Kubalski, Thomas T1 - Verbesserte seismische Nachweiskonzepte für Mauerwerksbauten in deutschen Erdbebengebieten T2 - Adam, Christoph (Hrsg.) ; Univ. Innsbruck: 16. D-A-CH Tagung Erdbebeningenieurwesen & Baudynamik 2019 : 26. und 27. September 2019, Innsbruck Y1 - 2019 SN - 978-3-200-06454-6 SP - 713 EP - 722 CY - Innsbruck ER - TY - CHAP A1 - Wulfhorst, Helene A1 - Merseburg, Johannes A1 - Tippkötter, Nils T1 - Analyse von Lignocellulose mittels dynamischer Differenzkalorimetrie und Infrarot – Spektrometrie T2 - 12. Dresdner Sensor-Symposium 2015 2015-12-07 - 2015-12-09 Y1 - 2015 SN - 978-3-9813484-9-1 U6 - http://dx.doi.org/10.5162/12dss2015/P6.2 SP - 210 EP - 215 ER - TY - CHAP A1 - Wulfhorst, H. A1 - Duwe, A. A1 - Möhring, S. A1 - Jurca, O. A1 - Tippkötter, Nils T1 - Analysis of pretreated biomass by differential scanning 132 calorimetry and multivariate data analysis T2 - New frontiers of biotech-processes (Himmelfahrtstagung) : 02-04 May 2016, Rhein-Mosel-Halle, Koblenz/Germany Y1 - 2016 SP - 132 PB - DECHEMA CY - Frankfurt am Main ER - TY - CHAP A1 - Wu, Ziyi A1 - Kemper, Hans T1 - The optimal 48 V – battery pack for a specific load profile of a heavy duty vehicle T2 - 8. Internationale Fachtagung Kraftwerk Batterie : 26. – 27. April 2016, Münster, Deutschland Y1 - 2016 ER - TY - CHAP A1 - Wu, Chunsheng A1 - Poghossian, Arshak A1 - Werner, Frederik A1 - Bronder, Thomas A1 - Bäcker, Matthias A1 - Wang, Ping A1 - Schöning, Michael Josef T1 - An application of a scanning light-addressable potentiometric sensor for label-free DNA detection T2 - 11. Dresdner Sensor-Symposium : 9.-11.12.2013 Y1 - 2013 SN - 978-3-9813484-5-3 SP - 164 EP - 168 ER - TY - CHAP A1 - Wu, Chunsheng A1 - Bronder, Thomas A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - DNA-hybridization detection using light-addressable potentiometric sensor modified with gold layer T2 - Sensoren und Messsysteme 2014 ; Beiträge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in Nürnberg. (ITG-Fachbericht ; 250) Y1 - 2014 SN - 978-3-8007-3622-5 SP - 1 EP - 4 PB - VDE-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wollert, Jörg A1 - Vedral, Andreas T1 - Bluetooth - Integrationstechnologie für automotive Anwendungen T2 - Begleittexte zum Entwicklerforum ZigBee & Co. - Drahtlose Nahbereichsnetzwerke : 20. April 2005, München-Dornach Y1 - 2005 ER - TY - CHAP A1 - Wollert, Jörg A1 - Vedral, Andreas T1 - Einsatz von Opensource-Software für Evaluationsprototypen : Anwendungsempfehlungen und Einsatzbeispiele T2 - Vorträge und Begleittexte zum Entwicklerforum Wireless 2002 : Technologien und Grundlagen ; 16. Mai 2002 Y1 - 2002 SP - 37 EP - 46 PB - Design & Elektronik CY - Poing ER - TY - CHAP A1 - Wollert, Jörg A1 - Rau, S. T1 - Performance von embedded WLAN-Systemen bei koexistierenden Netzwerken T2 - KOMMA 2012 : Kommunikation in der Automation : 3. Jahreskolloquium Kommunikation in der Automation : Lemgo, 14.11.2012 / Jürgen Jasperneite ... (Hrsg.) Y1 - 2012 SN - 978-3-9814062-2-1 PB - Inst. für Industrielle Informationstechnik CY - Lemgo ER - TY - CHAP A1 - Wollert, Jörg A1 - Plessmann, K. W. T1 - Controlling processes by operating-point based hybride observers T2 - EUFIT '93 : September 7 - 10, 1993, Eurogress Aachen, Germany, proceedings / First European Congress on Fuzzy and Intelligent Technologies Y1 - 1993 SN - 3-86073-176-9 SP - 1151 EP - 1155 PB - Verl. d. Augustinus Buchh. CY - Aachen ER - TY - CHAP A1 - Wollert, Jörg T1 - Langzeitstatistische Untersuchungen zur Qualität von Funkkanälen für das industrielle Umfeld T2 - Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund ( Jörg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772) Y1 - 2006 SN - 3-18-377210-8 SP - 165 EP - 176 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wollert, Jörg T1 - Grundlagen Wireless - Was kann von Funktechnik erwartet werden? T2 - Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund / Jörg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772) Y1 - 2006 SN - 3-18-377210-8 SP - 314 EP - 323 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wollert, Jörg T1 - Technologischer Überblick - welches ist die richtige kabellose Technologie? Grenzen und Möglichkeiten der Funkübertragung sowie der konkreten Nutzung verschiedener Technolgien T2 - Wireless-Technologies-Kongress 2008 : von der Technologie zur Anwendung / Hrsg. Jörg F. Wollert Y1 - 2008 SN - 978-3-89838-608-1 SP - 349 PB - AKA CY - Heidelberg ER - TY - CHAP A1 - Wollert, Jörg T1 - Grundlagen Wireless Technologie T2 - Wireless Technologies : 12. Kongress, 22. - 23. September 2010, Bochum ; von der Technologie zur Anwendung / Jörg F. Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; 810) Y1 - 2010 SP - 322 EP - 330 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wollert, Jörg T1 - Hybride arbeitspunktabhängige Beobachter zur intelligenten Modellierung und Regelung nichtlinearer Strecken T2 - Fuzzy control : GMA-Aussprachetag ; Tagung Langen, 22. und 23. März 1994. (VDI-Berichte ; 1113) Y1 - 1994 SN - 3-18-091113-1 SP - 497 EP - 506 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wollert, Jörg T1 - The performance of UWB-communication in an industrial environment T2 - IEEE 1st International Symposium on Wireless Systems : (IDAACS-SWS) : Offenburg, 20-21 Sept. 2012 Y1 - 2012 SN - 978-1-4673-4678-8 U6 - http://dx.doi.org/10.1109/IDAACS-SWS.2012.6377639 SP - 85 EP - 90 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Wollert, Jörg T1 - Mobility - Integration von Offboard-Devices in Fahrzeugen T2 - Begleittexte zum Entwicklerforum Kfz-Elektronik & FlexRay Solution Day : 15. Mai 2007, Ludwigsburg / hrsg. von Caspar Grote ... Y1 - 2007 SP - 47 EP - 54 PB - Design & Elektronik CY - Poing ER - TY - CHAP A1 - Wollert, Jörg T1 - Fahrzeug-Umwelt Kommunikation? Chancen und Herausforderungen T2 - Begleittexte zum Entwicklerforum Kfz-Elektronik & FlexRay Solution Day : 15. Mai 2007, Ludwigsburg / hrsg. von Caspar Grote ... Y1 - 2007 SP - 39 EP - 46 PB - Design & Elektronik CY - Poing ER - TY - CHAP A1 - Wollert, Jörg T1 - Performanceanforderungen von Funkstrecken in der Prozess- und Fertigungsautomation T2 - Automation 2008: Lösungen für die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032) Y1 - 2008 SN - 978-3-18-092032-0 SP - 247 EP - 248 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wollert, Jörg T1 - Echtzeitlösungen für Windows NT T2 - Kongreßband = Conference proceedings / Echtzeit '97, Kongreß & Messe für Industrielle Busse und Netze; INet '97, Kongreß & Messe für Industrielle Computer-Anwendungen, 9. - 11. September 1997, Wiesbaden Y1 - 1997 SP - 13 EP - 29 CY - Wiesbaden ER - TY - CHAP A1 - Wollert, Jörg T1 - Harte Echtzeit für Windows T2 - Tagungsband : SPS/IPC/Drives '99 : 10. Fachmesse und Kongress, 23. - 25. November 1999 Nürnberg Y1 - 1999 SN - 3-7785-2788-6 SP - 172 EP - 182 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Wollert, Jörg T1 - Echtzeiteigenschaften für Automatisierungsanwendungen mit Ethernet und TCP/IP T2 - Tagungsband - SPS/IPC/Drives 2000 : elektrische Automatisierung - Systeme und Komponenten ; 11. Fachmesse & Kongress 28. - 30. Nov. 2000, Nürnberg. (Praxiswissen : Automatisierung) Y1 - 2000 SN - 3-7785-2836-X SP - 124 EP - 132 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Wollert, Jörg T1 - Internettechnologie und Multimedia für Steuerungssysteme T2 - Tagungsband - SPS/IPC/Drives 2000 : elektrische Automatisierung - Systeme und Komponenten ; 11. Fachmesse & Kongress 28. - 30. Nov. 2000, Nürnberg. (Praxiswissen : Automatisierung) Y1 - 2000 SN - 3-7785-2836-X SP - 78 EP - 86 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Wollert, Jörg T1 - 10 Regeln für das Desaster T2 - Logistik IT Erfolgsfaktor oder Risiko? : Tagung Rüsselsheim, 14. und 15. November 2001. (VDI-Berichte ; 1633) Y1 - 2001 SN - 3-18-091633-8 SP - 1 EP - 16 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wollert, Jörg T1 - Ein Low-Power Bordrechner als Kommunikationsgateway für den Automotive-Bereich T2 - Bluetooth : 4. Kongress, Dortmund, 29. - 30 Januar 2003 Y1 - 2003 SP - 1 EP - 9 PB - Mesago Messe Frankfurt GmbH CY - Stuttgart ER - TY - CHAP A1 - Wollert, Jörg T1 - Einsatz von Wireless Technologien im Kraftfahrzeug T2 - Sichere Datenkommunikation im Automobil : Kongress ; 18. - 19. November 2003, Radisson SAS Hotel, Köln Y1 - 2003 SP - Getr. Zählung CY - Köln ER - TY - CHAP A1 - Wollert, Jörg T1 - Modellierung intelligenter Regelungen mit analytischen und heuristischen Merkmalen T2 - 39. Internationales Wissenschaftliches Kolloquium / Technische Universität Ilmenau, Thüringen : 27.-30.09.1994 Y1 - 1994 SN - 0943-7207 SP - 181 EP - 188 PB - Techn. Univ. CY - Ilmenau ER - TY - CHAP A1 - Wollert, Jörg T1 - Objekt-orientierte Modellierung hybrider Systeme mit heuristischen und analytischen Merkmalen T2 - Berichtsband / 4. Workshop "Fuzzy Control" des GMA-UA 1.4.2. am 03./04.11.1994 in Dortmund. (Forschungsbericht / Universität Dortmund, Fakultät für Elektrotechnik ; 1/94) Y1 - 1994 SP - 246 EP - 257 PB - Univ., Fak. f. Elektrotechnik CY - Dortmund ER - TY - CHAP A1 - Wollert, Jörg T1 - Wireless-Technologie - eine neue Chance für lokationsbezogene Dienste T2 - SPS/IPC/DRIVES 2003 : SPS/IPC/DRIVES/Elektrische Automatisierung - Systeme und Komponenten, Fachmesse & Kongress 25. - 27. Nov. 2003, Nürnberg ; [Tagungsband] Y1 - 2003 SN - 3-8007-2793-5 SP - 253 EP - 260 PB - VDE-Verl. CY - Berlin [u.a.] ER - TY - CHAP A1 - Wollert, Jörg T1 - Sicherheit und Sicherheitslücken in kabellosen Automatisierungsnetzwerken : wieviel Sicherheit braucht ein Automatisierungsnetzwerk? T2 - Funkgestützte Kommunikation in der industriellen Automatisierungstechnik : Tagung Düsseldorf, 4. und 5. Mai 2004. (VDI-Berichte ; 1843) Y1 - 2004 SN - 3-18-091843-8 SP - 91 EP - 104 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wollert, Jörg T1 - Bluetooth in Embedded-Anwendungen in der Automatisierungstechnik T2 - Tagungsband / SPS IPC Drives 2002 : 13. Fachmesse und Kongress, 26. - 28. November 2002 Nürnberg; elektrische Automatisierung - Systeme und Komponenten. (Praxiswissen IEE - Automatisierung) Y1 - 2002 SN - 3-7785-2863-7 SP - 28 EP - 37 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Wollert, Jörg T1 - Windows und Echtzeit? - Ein kritischer Blick auf Windows NT als Echtzeitbetriebssystem T2 - Tagungsband / 8. Int. Fachmesse und Kongress für Speicherprogrammierbare Steuerungen, Industrie-PCs und Elektrische Antriebstechnik, Nürnberg, 25. - 27. Nov. 1997; SPS IPC Drives Y1 - 1997 SN - 3-7785-2683-9 SP - 250 EP - 260 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Wollert, Jörg T1 - Sicherheit in kabellosen Netzwerken T2 - SPS/IPC/DRIVES 2004 : SPS/IPC/DRIVES, Elektrische Automatisierung - Systeme und Komponenten, Fachmesse & Kongress, 23. - 25. Nov. 2004, Nürnberg Y1 - 2004 SN - 3-7723-6709-7 SP - 335 EP - 341 PB - Poing CY - Franzis ER - TY - CHAP A1 - Wollert, Jörg T1 - Webbased Control technischer Anlagen T2 - Virtuelle Laboratorien : Vorträge zum 52. Berg- und Hüttenmännischen Tag 2001 in Freiberg Y1 - 2001 SN - 3860121456 SP - 111 EP - 120 PB - TU Bergakademie CY - Freiberg ER - TY - CHAP A1 - Wollert, Jörg T1 - Industrie 4.0 - warten bis die Revolution vorbei ist? T2 - Automatisierung im Fokus von Industrie 4.0 : Tagungsband AALE 2016 ; 13. Fachkonferenz, Lübeck Y1 - 2016 SN - 978-3-8356-7312-0 N1 - AALE-Konferenz <13., 2016, Lübeck> SP - 127 EP - 136 PB - DIV Deutscher Industrieverlag GmbH CY - München ER - TY - CHAP A1 - Wollert, Jörg T1 - Wireless systems for machinery safety : Requirements and solutions for wireless real time systems T2 - 16th International Conference on Research and Education in Mechatronics (REM), 2015 Y1 - 2015 SN - 978-3-945728-01-7 U6 - http://dx.doi.org/10.1109/REM.2015.7380377 SP - 88 EP - 91 ER - TY - CHAP A1 - Wolf, Martin A1 - Wiese, Ute T1 - A comparative transformation model for process changes using serious games T2 - 2013 IEEE 2nd International Conference on Serious Games and Applications for Health (SeGAH): proceedings of a meeting held 2-3 May 2013, Algarve, Portugal Y1 - 2013 SN - 978-1-4673-6164-4 U6 - http://dx.doi.org/10.1109/SeGAH.2013.6665307 SP - 64 EP - 70 PB - Institute of Electrical and Electronics Engineers (IEEE) CY - Piscataway, NJ ER - TY - CHAP A1 - Wolf, Martin A1 - Wiedenmaier, S. A1 - Schlick, Christopher ED - Herrmann, Thomas T1 - Flexible Kooperation durch computergestützte Teamarbeit T2 - Groupware und organisatorische Innovation : Tagungsband der Deutschen Fachtagung zu Computer Supported Cooperative Work. - (Berichte des German Chapter of the ACM ; Bd. 51) Y1 - 1998 SN - 3-519-02692-9 SP - 349 EP - 350 PB - Teubner CY - Stuttgart ER - TY - CHAP A1 - Wolf, Martin A1 - Ulbrich, Daniel T1 - Decision-Support-System kokas zur Sanierungsplanung und Strategieentwicklung N2 - Dr.-Ing. Martin Wolf ; Dipl.-Kaufm. Daniel Ulbrich , Dr. Pecher und Partner Ingenieurgesellschaft mbH, München. 31 S. (S. 139-168). Beitrag zum 1. Aachener Softwaretag in der Wasserwirtschaft < 1, 2007, Aachen>. Zusammenfasung [der Autoren] Die öffentlichen Kanalnetze Deutschlands stellen mit einem Wert von rd. 330 Mrd. € ein enormes Anlagevermögen dar. Auf Grund des oft schlechten Zustandes und geringer Ausgaben zur Instandhaltung und Erneuerung ist zu erwarten, dass durch die gegenwärtige Sanierungspraxis eher ein Substanzwertverzehr des Kanalnetzes als ein Substanzwerterhalt im Sinne des Generationenvertrages erzielt wird. Für einen nachhaltigen Betrieb und Erhalt der Kanalnetze sind deshalb Sanierungsstrategien erforderlich, die neben den technischen und gesetzlichen Anforderungen auch den mittel- und langfristigen Substanzwertverlauf berücksichtigen. Dieser wird beeinflusst vom erforderlichen oder durchgeführten Sanierungsumfang, Art und Zusammensetzung der ausgewählten Maßnahmen sowie der zeitlichen Abfolge der Sanierungsmaßnahmen. Erheblichen Einfluss auf den Substanzwertverlauf hat zudem die Berücksichtigung der hydraulischen Verhältnisse sowie der optisch nicht sichtbaren Undichtheiten. Entsprechend ist es erforderlich, die tatsächlich vorhandenen Defizite zu ermitteln und die Sanierungsmaßnahmen sowie eine Strategie zur Umsetzung zu erarbeiten. Da sich gezeigt hat, dass alleine die Einhaltung der technischen und gesetzlichen Anforderung für einen Substanzwerterhalt nicht ausreicht, muss die geplante Strategie im Dr.-Ing. Martin Wolf 139 von 170 Decision-Support-System kokas zur Sanierungsplanung und Strategieentwicklung 1. Aachener Softwaretag in der Wasserwirtschaft Hinblick auf die nachhaltige Wertentwicklung überprüft und ggf. Anpassungen vorgenommen werden. Kurzfristig erzielte Einsparungen durch reduzierten Schadensumfang oder einseitige Maßnahmenwahl ermöglichen zwar im günstigsten Fall, die Anforderungen einzuhalten, gehen jedoch zwangsläufig zu Lasten des Substanzwertes und führen mittel- und langfristig zu einer Verschärfung der Kosten- und Gebührensituation. Der monetäre, am konkreten Sanierungsaufwand orientierte Substanzwertansatz ermöglicht dabei, technische und kaufmännische Gesichtspunkte praxisnah zu verknüpfen und den bestmöglichen Ausgleich zwischen den gegenläufigen Zielen Substanzwerterhalt und Gebührenkonstanz zu finden. KW - Kanalisation KW - Kanalsanierung Y1 - 2007 ER - TY - CHAP A1 - Wolf, Martin A1 - Schlick, Christopher A1 - Herbst, D. A1 - Springer, J. ED - Uellner, Stefan T1 - Einflussfaktoren auf den Erfolg von Telekooperation in großen Unternehmen T2 - Computer Supported Cooperative Work (CSCW) in großen Unternehmungen : Tagungsband zum Workshop der GI-Fachgruppe 5.5.1 "CSCW in Organisationen" und dem Technologiezentrum Darmstadt der Deutschen Telekom AG vom 09. - 10. Mai 1996 Y1 - 1996 SP - 1 EP - 12 PB - Dt. Telekom CY - Darmstadt ER - TY - CHAP A1 - Wolf, Martin A1 - Lenz, Laura L. T1 - The economic effectiveness of serious games in the healthcare environment : application and evaluation of the Comparative Transformation Model (CTM) T2 - IEEE 3rd International Conference on Serious Games and Applications for Health : SeGAH 2014 ; Rio de Janeiro, Brazil, May 14 - 16 Y1 - 2015 SN - 978-1-4799-4823-9 U6 - http://dx.doi.org/10.1109/SeGAH.2014.7067089 SP - 135 EP - 142 PB - IEEE [u.a.] CY - Piscataway, NJ ER - TY - CHAP A1 - Wolf, Martin A1 - König, Johannes Alexander ED - Eibl, Maximilian ED - Gaedke, Martin T1 - Competence Developing Games – Ein Überblick T2 - INFORMATIK 2017, Lecture Notes in Informatics (LNI), Gesellschaft für Informatik N2 - Es existieren verschiedenste Arten von Spielen, die versuchen, die Motivation einer Spielsituation in einen ernsten Kontext zu überführen. In diesem Artikel wird der Überbegriff „Competence Developing Games“ definiert und anhand von Beispielen erläutert. Dafür werden Erkennungskriterien vorgestellt, entsprechende Spieltypen erläutert und eine Zuordnung durch-geführt. KW - Competence Developing Gam KW - Serious Game KW - Education KW - Gamification KW - Bewertungsframework Y1 - 2017 SN - 978-3-88579-669-5 U6 - http://dx.doi.org/10.18420/in2017_32 SP - 385 EP - 391 ER - TY - CHAP A1 - Wolf, Martin A1 - Barton, Thomas A1 - Herrmann, Frank A1 - Meister, Vera G. A1 - Müller, Christian A1 - Seel, Christian T1 - Angewandte Forschung in der Wirtschaftsinformatik 2019 : Tagungsband zur 32. AKWI-Jahrestagung vom 15.09.2019 bis 18.09.2019 an der Fachhochschule für Angewandte Wissenschaften Aachen / hrsg. von Martin R. Wolf, Thomas Barton, Frank Herrmann, Vera G. Meister, Christian Müller, Christian Seel N2 - Tagungsbeiträge aus den Bereichen Projektmanagement, Didaktik in der Wirtschaftsinformatik, IT-Sicherheit, Anwendungsfälle, Reifegradmodelle, Plattformen für Geschäftsprozesse und Prototypen. Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-13026 SN - 978-3-944330-62-4 PB - mana-Buch CY - Heide ER - TY - CHAP A1 - Wittig, M. A1 - Rütters, René A1 - Bragard, Michael ED - Reiff-Stephan, Jörg ED - Jäkel, Jens ED - Schwarz, André T1 - Application of RL in control systems using the example of a rotatory inverted pendulum T2 - Tagungsband AALE 2024 : Fit für die Zukunft: praktische Lösungen für die industrielle Automation N2 - In this paper, the use of reinforcement learning (RL) in control systems is investigated using a rotatory inverted pendulum as an example. The control behavior of an RL controller is compared to that of traditional LQR and MPC controllers. This is done by evaluating their behavior under optimal conditions, their disturbance behavior, their robustness and their development process. All the investigated controllers are developed using MATLAB and the Simulink simulation environment and later deployed to a real pendulum model powered by a Raspberry Pi. The RL algorithm used is Proximal Policy Optimization (PPO). The LQR controller exhibits an easy development process, an average to good control behavior and average to good robustness. A linear MPC controller could show excellent results under optimal operating conditions. However, when subjected to disturbances or deviations from the equilibrium point, it showed poor performance and sometimes instable behavior. Employing a nonlinear MPC Controller in real time was not possible due to the high computational effort involved. The RL controller exhibits by far the most versatile and robust control behavior. When operated in the simulation environment, it achieved a high control accuracy. When employed in the real system, however, it only shows average accuracy and a significantly greater performance loss compared to the simulation than the traditional controllers. With MATLAB, it is not yet possible to directly post-train the RL controller on the Raspberry Pi, which is an obstacle to the practical application of RL in a prototyping or teaching setting. Nevertheless, RL in general proves to be a flexible and powerful control method, which is well suited for complex or nonlinear systems where traditional controllers struggle. KW - Rotatory Inverted Pendulum KW - MPC KW - LQR KW - PPO KW - Reinforcement Learning Y1 - 2024 SN - 978-3-910103-02-3 U6 - http://dx.doi.org/10.33968/2024.53 N1 - 20. AALE-Konferenz. Bielefeld, 06.03.-08.03.2024. (Tagungsband unter https://doi.org/10.33968/2024.29) SP - 241 EP - 248 PB - le-tex publishing services GmbH CY - Leipzig ER - TY - CHAP A1 - Wiezik, P. A1 - Hötter, Jan-Steffen A1 - Gebhardt, Andreas T1 - Integration des Laserpolierens in den SLM-Prozess T2 - DVS Congress 2015, Große Schweißtechnische Tagung, DVS-Studentenkongress, Fügen von faserverstärkten Kunststoffen, Anwendungsnahe Schweißsimulation, Vorträge der Veranstaltungen, Nürnberg, DE, 15.-17. Sep, 2015 Y1 - 2015 SN - 978-3-945023-46-4 VL - 315 SP - 117 EP - 120 PB - Verl. für Schweißen und verwandte Verfahren, DVS-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Wiesen, Patrick A1 - Engemann, Heiko A1 - Limpert, Nicolas A1 - Kallweit, Stephan T1 - Learning by Doing - Mobile Robotics in the FH Aachen ROS Summer School T2 - European Robotics Forum 2018, TRROS18 Workshop Y1 - 2018 SP - 47 EP - 58 ER - TY - CHAP A1 - Wiesen, Andreas A1 - Schleser, Markus T1 - Entwicklung einer Qualitätssicherung für das Laserstrahlschweißen im Vakuum mittels Bildverarbeitung T2 - Große Schweißtechnische Tagung Y1 - 2019 SN - 978-3-96144-066-5 N1 - DVS CONGRESS 2019, Große Schweißtechnische Tagung, DVS-Studentenkongress. 16. bis 17. September 2019, Düsseldorf. DVS-Berichte, Band 355 SP - 1 EP - 6 PB - DVS-Media CY - Düsseldorf ER - TY - CHAP A1 - Wiegner, Jonas A1 - Volker, Hanno A1 - Mainz, Fabian A1 - Backes, Andreas A1 - Löken, Michael A1 - Hüning, Felix T1 - Wiegand-effect-powered wireless IoT sensor node T2 - Sensoren und Messsysteme 2022 N2 - In this article we describe an Internet-of-Things sensing device with a wireless interface which is powered by the oftenoverlooked harvesting method of the Wiegand effect. The sensor can determine position, temperature or other resistively measurable quantities and can transmit the data via an ultra-low power ultra-wideband (UWB) data transmitter. With this approach we can energy-self-sufficiently acquire, process, and wirelessly transmit data in a pulsed operation. A proof-of-concept system was built up to prove the feasibility of the approach. The energy consumption of the system is analyzed and traced back in detail to the individual components, compared to the generated energy and processed to identify further optimization options. Based on the proof-of-concept, an application demonstrator was developed. Finally, we point out possible use cases. Y1 - 2022 SN - 978-3-8007-5835-7 SP - 255 EP - 260 PB - VDE Verlag GmbH CY - Berlin ER - TY - CHAP A1 - Weßling, Matthias T1 - Leadership Perspectives: Research Findings, Theories, Practical Experiences N2 - Leadership Perspectives: Research Findings, Theories, Practical Experiences: Results of Leadership Research and exemplarily application cases show the perspectives and consequences for leadership practice and the following requirements for executives in future. N2 - Leadership Perspectives: Research Findings, Theories, Practical Experiences: Bisherige Ergebnisse der betriebswirtschaftlichen Führungsforschung und exemplarische Anwendungsbeispiele der Führungspraxis, sowie die Schlußfolgerungen für die Perspektiven der betrieblichen Mitarbeiterführung sowie die sich daraus ergebenden Anforderungen an zukünftige Führungskräfte. KW - Leadership KW - Führung KW - Führungsansätze KW - Leadership KW - Self-Leadership KW - Leadership Approaches KW - Skill Assessment KW - Leadership Theories Y1 - 2007 ER - TY - CHAP A1 - Weßling, Matthias T1 - Motivation and Leadership - The Reiss-Profile of the 16 Basic Desires: Research results and managerial applications N2 - Recent Results of the scientific Reiss-Profile (16 basic desires) due to the concept of Prof. Dr. Steven Reiss (State University Ohio, U.S.A.), supplemented by the comparative analysis of empirical motivational profiles of european executives of various companies. N2 - Neuere Forschungsergebnisse des wissenschaftlichen Reiss-Profils der 16 Lebensmotive nach Prof. Dr. Steven Reiss (State University Ohio, U.S.A.) und die Möglichkeiten und Grenzen ihrer Umsetzung in der betrieblichen Führungspraxis unter Integration der vergleichenden Analyse und Interpretation empirisch erhobener Motivprofile einzelner europäischer Führungskräfte. KW - Motivation KW - Leadership KW - Motivation KW - Führung KW - Motivation KW - Leadership Y1 - 2007 ER - TY - CHAP A1 - Weßling, Matthias T1 - Provocative Communication in Coaching and Leadership: scientific research and managerial applications of the Provocative Communication Style N2 - Concept, scientific research and managerial applications of Provocative Coaching, according to the „Provocative Therapy“ of Prof. Dr. Frank Farrelly (University of Wisconsin, U.S.A) in terms of an application of the Provocative Communication Style in specific situations of practical leadership, especially in the role of a coach for their subordinates. N2 - Konzept, Forschungsergebnisse und Tools der sogenannten „Provocative Therapy“ nach Prof. Dr. Frank Farrelly (University of Wisconsin, U.S.A) und ihre Anwendung als provokativer Kommunikationsstil einer Führungskraft in spezifischen Situationen der betrieblichen Führungspraxis in der Rolle eines Coaches. KW - Kommunikation KW - Coaching KW - Führung KW - Kommunikation KW - Coaching KW - Führung KW - Provokativer Stil KW - Provocative Coaching KW - Leadership KW - Communication KW - Provocative Style Y1 - 2007 ER - TY - CHAP A1 - Weßling, Matthias T1 - Como motivar a si mesmo e aos outros - o valor dos 16 Motivos Vitais para Liderança N2 - O Perfil Reiss apresenta no resultado uma visão da estrutura dos motivos e impulsos de uma pessoa. O ponto de saída para a análise do resultado é o conhecimento de que os motivos vitais (= valores e metas de sobrevivência) formam a moldura, na qual as competências e capacidades que uma pessoa possui possam se desabrochar de forma ideal. A partir desse princípio, não existe no Perfil Reiss nenhum resultado que se possa classificar como correto ou falso, nem como bom ou mau. Uma comparação entre o resultado do Perfil Reiss e o conteúdo de uma atividade apresentada ou ambicionada dá informação sobre até que ponto a capacidade de rendimento de uma pessoa nessa posição pode vir ou virá a se desenvolver por um longo tempo. N2 - Das Reiss-Profil der 16 Lebensmotive ist Ergebnis einer umfassenden, länderübergreifenden empirischen Datenerhebung und beruht auf einer bislang einzigartigen empirischen Forschungsbasis. Es überprüft die Kongruenz zwischen dem Anforderungsprofil eines Stelle und dem Motivationsprofil eines Menschen. Das Reiss-Profil lässt bewusste und unbewusste Motive und Antriebe von Mitarbeitern erkennen, die neue Management-Firmeninitiativen blockieren oder fördern können. Bereits im Vorfeld werden für den einzelnen Mitarbeiter außerordentlich wichtige Werte anhand ihres Motivprofils erkannt und können besser in die Gruppe integriert werden. Im Endergebnis verdeutlicht diese Perspektive für die betriebliche Mitarbeitermotivation eine vollkommene Individualisierung, wenngleich das Ausmaß auch kulturabhängig relativiert werden muß. T2 - How to motivate yourself and other people - the value of the 16 basic desires for leadership KW - Führung KW - Motivation KW - Führung KW - Motivation KW - Leadership KW - Motivation KW - Self-Leadership Y1 - 2006 ER - TY - CHAP A1 - Wetter, Martin A1 - Kern, Alexander T1 - Number of lightning strikes to tall structures - comparison of calculations and measurements using a modern lightning monitoring system T2 - 2014 International Conference on Lightning Protection (ICLP), Shanghai, China Y1 - 2014 SP - 1 EP - 7 ER - TY - CHAP A1 - Werner, Frederik A1 - Yoshinobu, T. A1 - Miyamoto, K. A1 - Schöning, Michael Josef A1 - Wagner, Torsten T1 - Semiconductor-based sensors for imaging of chemical processes T2 - Sensoren und Messsysteme 2014 ; Beiträge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in Nürnberg. (ITG-Fachbericht ; 250) Y1 - 2014 SN - 978-3-8007-3622-5 SP - 1 EP - 5 PB - VDE-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Werner, Frederik A1 - Mansour, Ahmed A1 - Rateike, Franz-Matthias A1 - Schusser, Sebastian A1 - Wagner, Torsten A1 - Yoshinobu, Tatsuo A1 - Keusgen, Michael A1 - Schöning, Michael Josef ED - Gerlach, Gerald T1 - Kompakter Aufbau eines lichtadressierbaren potentiometrischen Sensors mit verfahrbarem Diodenlaser T2 - 10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren für Bioprozess- und Verfahrenstechnik, Sensoren für die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorlösungen, Sensoren für die Wasserqualität, Selbstüberwachung / Gerald Gerlach ... (Hg.) Dresdner Beiträge zur Sensorik. 43 Y1 - 2011 SN - 978-3-942710-53-4 SP - 277 EP - 280 PB - TUDpress CY - Dresden ER - TY - CHAP A1 - Wellmer, Georg A1 - Chen, B.-H. A1 - Braun, Carsten A1 - Ballmann, Josef T1 - Numerical prediction of aeroelastic effects on twin-sting-rig mounted models for rear fuselage and empennage flow investigation in transonic windtunnel T2 - Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics, June 18 - 21, 2007, Stockholm, Sweden Y1 - 2007 PB - KTH CY - Stockholm ER - TY - CHAP A1 - Wellmann, Judith T1 - Perspektiven eines Bauingenieurs im konstruktiven Ingenieurbau N2 - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 7-12 Die Berufsperspektiven im konstruktiven Ingenieurbau werden trotz sinkendem Bedarf an Statikern positiv bewertet. KW - Ingenieurbau KW - Konstruktiver Ingenieurbau KW - Statiker KW - Berufsperspektiven Y1 - 2006 ER - TY - CHAP A1 - Welden, Melanie A1 - Severins, Robin A1 - Poghossian, Arshak A1 - Wege, Christina A1 - Siegert, Petra A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Studying the immobilization of acetoin reductase with Tobacco mosaic virus particles on capacitive field-effect sensors T2 - 2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN) N2 - A capacitive electrolyte-insulator-semiconductor (EISCAP) biosensor modified with Tobacco mosaic virus (TMV) particles for the detection of acetoin is presented. The enzyme acetoin reductase (AR) was immobilized on the surface of the EISCAP using TMV particles as nanoscaffolds. The study focused on the optimization of the TMV-assisted AR immobilization on the Ta 2 O 5 -gate EISCAP surface. The TMV-assisted acetoin EISCAPs were electrochemically characterized by means of leakage-current, capacitance-voltage, and constant-capacitance measurements. The TMV-modified transducer surface was studied via scanning electron microscopy. KW - Tobacco mosaic virus KW - acetoin KW - capacitive field-effect biosensor KW - enzyme immobilization Y1 - 2022 SN - 978-1-6654-5860-3 (Online) SN - 978-1-6654-5861-0 (Print) U6 - http://dx.doi.org/10.1109/ISOEN54820.2022.9789657 N1 - IEEE International Symposium on Olfaction and Electronic Nose (ISOEN), 29 May 2022 - 01 June 2022, Aveiro, Portugal. PB - IEEE ER - TY - CHAP A1 - Weiss, Christian A1 - Heslenfeld, Jonas A1 - Saewe, Jasmin Kathrin A1 - Bremen, Sebastian A1 - Häfner, Constantin Leon T1 - Investigation on the influence of powder humidity in Laser Powder Bed Fusion (LPBF) T2 - Procedia CIRP N2 - In the Laser Powder Bed Fusion (LPBF) process, parts are built out of metal powder material by exposure of a laser beam. During handling operations of the powder material, several influencing factors can affect the properties of the powder material and therefore directly influence the processability during manufacturing. Contamination by moisture due to handling operations is one of the most critical aspects of powder quality. In order to investigate the influences of powder humidity on LPBF processing, four materials (AlSi10Mg, Ti6Al4V, 316L and IN718) are chosen for this study. The powder material is artificially humidified, subsequently characterized, manufactured into cubic samples in a miniaturized process chamber and analyzed for their relative density. The results indicate that the processability and reproducibility of parts made of AlSi10Mg and Ti6Al4V are susceptible to humidity, while IN718 and 316L are barely influenced. KW - LPBF KW - Additive Manufacturing KW - Powder Material KW - Humidity Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.procir.2022.08.102 SN - 2212-8271 N1 - Teil der Sonderausgabe: 12th CIRP Conference on Photonic Technologies [LANE 2022] VL - 111 SP - 115 EP - 120 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Weiss, Alexander A1 - Abanteriba, Sylvester A1 - Esch, Thomas T1 - Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow T2 - Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B N2 - Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations. Y1 - 2007 SN - 0-7918-4288-6 U6 - http://dx.doi.org/10.1115/FEDSM2007-37387 N1 - Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B. San Diego, California, USA. July 30–August 2, 2007 SP - 1861 EP - 1871 PB - American Society of Mechanical Engineers (ASME) CY - New York ER - TY - CHAP A1 - Weingart, Daniel A1 - Schneider, Ulf A1 - Wollert, Jörg T1 - Doppelt gekoppelt - Kabellose und dynamische Anbindung von CANopen an Profinet IO T2 - Elektrische Automatisierung - Systeme und Komponenten: SPS-IPC-Drives 2009, Fachmesse & Kongress, 24. - 26. Nov. 2009, Nürnberg ; [Tagungsband] Y1 - 2009 SN - 978-3-8007-3184-8 SP - 147 EP - 154 PB - VDE-Verl. CY - Berlin [u.a.] ER - TY - CHAP A1 - Weil, M. A1 - Poghossian, Arshak A1 - Schöning, Michael Josef A1 - Cherstvy, A. T1 - Electrical monitoring of layer-by-layer adsorption of oppositely charged macromolecules by means of capacitive field-effect devices Y1 - 2012 SN - 978-3-9813484-2-2 U6 - http://dx.doi.org/10.5162/IMCS2012/P2.5.2 SP - 1575 EP - 1578 ER - TY - CHAP A1 - Weber, Tobias A1 - Tellis, Jane J. A1 - Duhovic, Miro T1 - Characterization of tool-part-interaction an interlaminar friction for manufacturing process simulation T2 - ECCM 17, 17th European Conference on Composite Materials, München, DE, Jun 26-30, 2016 Y1 - 2016 SN - 978-3-00-053387-7 SP - 1 EP - 7 ER - TY - CHAP A1 - Weber, Tobias A1 - Englhard, Markus A1 - Hailer, Benjamin A1 - Arent, Jan-Christoph T1 - Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling T2 - Proceedings of SAMPE Europe Conference 2019, Nantes, France Y1 - 2019 SP - 1 EP - 10 ER - TY - CHAP A1 - Weber, Tobias A1 - Englhard, Markus A1 - Hailer, Benjamin A1 - Arent, Jan-Christoph T1 - Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling T2 - Proceedings of SAMPE Europe Conference, Amiens , France Y1 - 2015 SP - 1 EP - 10 ER - TY - CHAP A1 - Weber, Tobias T1 - Manufacturing Process Simulation for Tooling Optimization: Reduction of Quality Issues During Autoclave Manufacturing of Composite Parts T2 - Proceedings of SAMPE Europe Conference 2015, Amiens, France Y1 - 2015 SP - 1 EP - 8 ER - TY - CHAP A1 - Weber, S. A1 - Terstegge, Andreas A1 - Halling, H. A1 - Herzog, H. A1 - Reinartz, R. A1 - Reinhart, P. A1 - Rongen, F. A1 - Müller-Gärtner, H.-W. T1 - The design of an animal PET: flexible geometry for achieving optimal spatial resolution or high sensitivity T2 - Conference record / 1995 IEEE Nuclear Science Symposium and Medical Imaging, October 21 - 28, 1995, San Francisco ; vol. 2 Y1 - 1995 SN - 078033180X ; 0780331818 ; 0780331826 SP - 1002 EP - 1005 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Weber, S. A1 - Terstegge, Andreas A1 - Engels, R. A1 - Herzog, H. A1 - Reinartz, R. A1 - Reinhart, P. A1 - Rongen, F. A1 - Müller-Gärtner, H. W. A1 - Halling, H. T1 - The KFA TierPET: performance characteristics and measurements T2 - Conference record / 1996 IEEE Nuclear Science Symposium [and Medical Imaging], November 2 - 9, 1996, Anaheim, California ; vol. 2 Y1 - 1996 SN - 0-7803-3534-1 SN - 1082-3654 SP - 1117 EP - 1119 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Weber, Niklas A1 - Wolf, Martin ED - Barton, Thomas T1 - Datenerhebung für die CDG-Forschung T2 - Prozesse, Technologie, Anwendungen, Systeme und Management 2017 : angewandte Forschung in der Wirtschaftsinformatik : Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg / Arbeitskreis Wirtschaftsinformatik an Fachhochschulen (AKWI) Y1 - 2017 SN - 978-3-944330-56-3 SP - 218 EP - 227 PB - mana-Buch CY - Heide ER - TY - CHAP A1 - Weber, Ingo A1 - Markovic, Ivan A1 - Drumm, Christian T1 - A conceptual framework for composition in business process management T2 - Business Information Systems : 10th International Conference, BIS 2007, Poznan, Poland, April 25-27, 2007. Proceedings Y1 - 2007 SN - 978-3-540-72035-5 U6 - http://dx.doi.org/10.1007/978-3-540-72035-5_5 SP - 54 EP - 66 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Weber, Hans-Joachim A1 - Porschen, W. A1 - Dietzel, F. A1 - [u.a.], ED - Streffer, Christian T1 - In vivo analysis of the influence of combined hyperthermia and gamma irradiation on euoxic and hypoxic tumor cells T2 - Cancer therapy by hyperthermia and radiation : [proceedings of the 2. International Symposium on Cancer Therapy by Hyperthermia and Radiation, Essen, 2.-4.6.1977] Y1 - 1978 SN - 0-8067-1701-7 SN - 3-541-71701-7 SP - 276 EP - 277 PB - Urban and Schwarzenberg CY - Baltimore ; Munich [u.a.] ER - TY - CHAP A1 - Warerkar, Shashikant A1 - Schmitz, Stefan A1 - Göttsche, Joachim A1 - Hoffschmidt, Bernhard A1 - Reißel, Martin A1 - Tamme, Rainer T1 - Air-sand heat exchanger for high-temperature storage T2 - Proceedings of the ASME 3rd International Conference on Energy Sustainability : July 19 - 23, 2009, San Francisco, California, USA. Vol. 2 Y1 - 2009 SN - 978-0-7918-4890-6 SP - 655 EP - 661 PB - ASME CY - New York, NY ER - TY - CHAP A1 - Warerkar, S. A1 - Schmitz, S. A1 - Göttsche, Joachim A1 - Hoffschmidt, Bernhard A1 - Tamme, R. T1 - Performance analysis of an air-sand heat exchanger prototype for high-temperature storage T2 - EuroSun 2008 : 1st International Conference on Solar Heating, Cooling and Buildings ; 7th - 10th October 2008, Lisbon, Portugal : key lectures / ISES, International Solar Energy Society. Vol. 1 Y1 - 2008 SN - 978-1-61782-228-5 SP - 2215 EP - 2222 PB - Sociedade Portuguesa De Energia Solar (SPES) CY - Lissabon ER - TY - CHAP A1 - Wang, W. A1 - Mensing, C. A1 - Gligorevic, Snjezana A1 - Jost, T. A1 - Dammann, A. T1 - Short term statistical analysis of outdoor to indoor propagation channel for geolocations T2 - Proceedings of the 13th International OFDM Workshop : (InOWo '08), Aug. 27./28. 2008, Hamburg : Session 3A: Systems concepts Y1 - 2008 SP - 85 EP - 89 ER - TY - CHAP A1 - Walter, Peter A1 - Elsen, Ingo A1 - Müller, Holger A1 - Kraiss, Karl-Friedrich T1 - 3D object recognition with a specialized mixtures of experts architecture T2 - IJCNN'99. International Joint Conference on Neural Networks. Proceedings N2 - Aim of the AXON2 project (Adaptive Expert System for Object Recogniton using Neuml Networks) is the development of an object recognition system (ORS) capable of recognizing isolated 3d objects from arbitrary views. Commonly, classification is based on a single feature extracted from the original image. Here we present an architecture adapted from the Mixtures of Eaqerts algorithm which uses multiple neuml networks to integmte different features. During tmining each neural network specializes in a subset of objects or object views appropriate to the properties of the corresponding feature space. In recognition mode the system dynamically chooses the most relevant features and combines them with maximum eficiency. The remaining less relevant features arz not computed and do therefore not decelerate the-recognition process. Thus, the algorithm is well suited for ml-time applications. Y1 - 1999 SN - 0-7803-5529-6 U6 - http://dx.doi.org/10.1109/IJCNN.1999.836243 SN - 1098-7576 N1 - Washington, DC 10-16.07.1999 SP - 3563 EP - 3568 PB - IEEE CY - New York ER - TY - CHAP A1 - Walter, Michael A1 - Gligorevic, Snjezana A1 - Detert, Thorben A1 - Schnell, Michael T1 - UHF/VHF air-to-air propagation measurements T2 - Proceedings of the Fourth European Conference on Antennas and Propagation (EuCAP) : 12 - 16 April 2010, Barcelona, Spain Y1 - 2010 SN - 978-1-4244-6431-9 ; 978-84-7653-472-4 SP - 1 EP - 5 ER - TY - CHAP A1 - Wallnöfer, Armin A1 - Drath, Rainer A1 - Hüning, Felix T1 - Was ist Funktionales Engineering? Einordnung, Definition, Randbedingungen T2 - Automation 2015 : 16. Branchentreff der Mess- und Automatisierungstechnik, 11. und 12. Juni 2015, Baden-Baden / VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik Y1 - 2015 SN - 978-3-18-092258-4 PB - VDI-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Walk-Lauffer, Bernd A1 - Raupach, Michael A1 - Dilger, Klaus A1 - Böhm, Stefan A1 - Mundt, F. A1 - Dilthey, Ulrich A1 - Schleser, Markus T1 - The interconnection between inner filaments of textile reinforcement by means of polymer modified concrete T2 - Proceedings of the First International Conference on Innovative Materials and Technologies for Construction and Restoration : : Lecce, June 6 - 9, 2004 / Università degli Studi di Lecce / ed. Antonio La Tegola. Vol. 1: Key-notes, materials, construction Y1 - 2004 SP - 150 EP - 159 PB - Liguori CY - Napoli ER - TY - CHAP A1 - Walenta, Robert A1 - Schellekens, Twan A1 - Ferrein, Alexander A1 - Schiffer, Stefan T1 - A decentralised system approach for controlling AGVs with ROS T2 - AFRICON, Proceedings Y1 - 2017 SN - 978-1-5386-2775-4 U6 - http://dx.doi.org/10.1109/AFRCON.2017.8095693 SN - 2153-0033 N1 - AFRICON <2017, 18-20 Sept., Cape Town, South Africa> SP - 1436 EP - 1441 PB - IEEE ER - TY - CHAP A1 - Waldmann, Christoph A1 - Vera, Jean-Pierre de A1 - Dachwald, Bernd A1 - Strasdeit, Henry A1 - Sohl, Frank A1 - Hanff, Hendrik A1 - Kowalski, Julia A1 - Heinen, Dirk A1 - Macht, Sabine A1 - Bestmann, Ulf A1 - Meckel, Sebastian A1 - Hildebrandt, Marc A1 - Funke, Oliver A1 - Gehrt, Jan-Jöran T1 - Search for life in ice-covered oceans and lakes beyond Earth T2 - 2018 IEEE/OES Autonomous Underwater Vehicle Workshop, Proceedings November 2018, Article number 8729761 N2 - The quest for life on other planets is closely connected with the search for water in liquid state. Recent discoveries of deep oceans on icy moons like Europa and Enceladus have spurred an intensive discussion about how these waters can be accessed. The challenge of this endeavor lies in the unforeseeable requirements on instrumental characteristics both with respect to the scientific and technical methods. The TRIPLE/nanoAUV initiative is aiming at developing a mission concept for exploring exo-oceans and demonstrating the achievements in an earth-analogue context, exploring the ocean under the ice shield of Antarctica and lakes like Dome-C on the Antarctic continent. KW - Planetary exploration KW - Jupiter KW - ice moons KW - underwater vehicle KW - Antarctica Y1 - 2018 U6 - http://dx.doi.org/10.1109/AUV.2018.8729761 ER - TY - CHAP A1 - Wahle, Michael A1 - Zeleny, R. T1 - Berechnung von Elastomer-Bauteilen bei quasistatischer Belastung unter Berücksichtigung von Eigenkontakt und äußeren Reibungseinflüssen T2 - 13. CAD-FEM Users' Meeting : FEM-Technologietage, 25. - 27. Oktober 1995 in Bad Wildungen bei Kassel / [Hrsg.: CAD-FEM GmbH] Y1 - 1995 N1 - CAD-FEM Users' Meeting <13, 1995, Wildungen> ; CADFEM GmbH SP - 5 EP - 6 CY - Grafing b. München [u.a.] ER -