TY - JOUR A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Voss, Michael T1 - Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 2) T1 - Design of reinforced concrete enclosures infilled with clay block masonry (Part 2) JF - Ziegelindustrie international : ZI = Brick and tile industry international N2 - Im Rahmen des europäischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragfähigkeit durch aufwendige und kostspielige zusätzliche Bewehrungseinlagen zu erhöhen. Erste Ergebnisse des Systems IMES für Belastungen in und senkrecht zu der Wandebene werden vorgestellt. N2 - Within the scope of the joint European project INSYSME, the German partners developed two systems - IMES and INODIS - for improving the seismic behaviour of masonry infilled reinforced concrete frames. The purpose of both systems is to decouple frame and infill instead of working to improve their load-bearing capacity by means of elaborate, expensive, supplementary reinforcing elements. Initial findings for the IMES system with regard to the loads acting in-plane and perpendicular to the wall plane (out-of-plane) are presented. Y1 - 2018 SN - 0341-0552 IS - 6 SP - 24 EP - 43 PB - Bauverlag BV GmbH CY - Gütersloh ER - TY - CHAP A1 - Hirsch, G. A1 - Wahle, Michael T1 - Auslegungskriterien für Dynamische Schwingungsdämpfer für schwach gedämpfte elastische Strukturen unter Berücksichtigung einer der Masseverteilung nicht proportionalen Zusatzdämpfung T2 - Hans Ebner : Gedächtnis-Kolloquium am 27./28. Oktober 1977 in Aachen. - (Mitteilung aus dem Institut für Leichtbau, Aachen ; 1) Y1 - 1978 SP - 374 EP - 400 CY - Aachen ER - TY - CHAP A1 - Dümmler, Andreas A1 - Oetringer, Kerstin A1 - Göttsche, Joachim T1 - Auslegungstool zur energieeffizienten Kühlung von Gebäuden T2 - DKV-Tagung 2020, AA IV N2 - Thematisch widmet sich das Projekt Coolplan- AIR der Fortentwicklung und Feldvalidierung eines Berechnungs- und Auslegungstools zur energieeffizienten Kühlung von Gebäuden mit luftgestützten Systemen. Neben dem Aufbau und der Weiterentwicklung von Simulationsmodellen erfolgen Vermessungen der Gesamtsysteme anhand von Praxisanlagen im Feld. Der Schwerpunkt des Projekts liegt auf der Vermessung, Simulation und Integration rein luftgestützter Kühltechnologien. Im Bereich der Kälteerzeugung wurden Luft‐ Luft‐ Wärmepumpen, Anlagen zur adiabaten Kühlung bzw. offene Kühltürme und VRF‐ Multisplit‐ Systeme (Variable Refrigerant Flow) im Feld bzw. auf dem Teststand der HSD vermessen. Die Komponentenmodelle werden in die Matlab/Simulink‐ Toolbox CARNOT integriert und anschließend auf Basis der zuvor erhaltenen Messdaten validiert. Einerseits erlauben die Messungen das Betriebsverhalten von Anlagenkomponenten zu analysieren. Andererseits soll mit der Vermessung im Feld geprüft werden, inwieweit die Simulationsmodelle, welche im Vorgängerprojekt aus Prüfstandmessungen entwickelt wurden, auch für größere Geräteleistungen Gültigkeit besitzen. Die entwickelten und implementierten Systeme, bestehend aus verschiedensten Anlagenmodellen und Regelungskomponenten, werden geprüft und dahingehend qualifiziert, dass sie in Standard- Auslegungstools zuverlässig verwendet werden können. Zusätzlich wird ein energetisches Monitoring eines Hörsaalgebäudes am Campus Jülich durchgeführt, das u. a. zur Validierung der Kühllastberechnungen in gängigen Simulationsmodelle genutzt werden kann. Y1 - 2020 N1 - Deutsche Kälte- und Klimatagung, 19-20 November 2020, online SP - 1109 ER - TY - JOUR A1 - Timme, Michael A1 - Raue, Benjamin T1 - Ausschluss des Zurückbehaltungsrechts bei fehlender Mängelanzeige JF - Neue Zeitschrift für Miet- und Wohnungsrecht [Elektronische Ressource] : NZM ; Miete, Wohnungseigentum, Pacht, Makler- und Bauträgerrecht, Steuern, Wohnungswirtschaft, Versicherung, Immobilienleasing Y1 - 2011 SN - 1434-677X VL - 14 IS - 23 SP - 846 EP - 849 PB - Beck CY - München ER - TY - GEN A1 - Olbertz, Klaus T1 - Ausschluss von Sozialplanabfindung und Klageverzichtsprämie T2 - Gesellschafts- und Wirtschaftsrecht : GWR Y1 - 2018 SN - 1868-1816 N1 - Anm. zu BAG: Entscheidungsbesprechung zum Urteil v. 08.12.2015 - 1 AZR 595/14 SP - 391 EP - 391 ER - TY - BOOK A1 - Breitbach, Gerd A1 - David, H.P. A1 - Nickel, M. A1 - Wolters, J. T1 - Ausström- und Gasaustauschvorgänge nach Lecks im Primärkreislauf von Hochtemperaturreaktoren Y1 - 1988 N1 - (Spezielle Berichte der Kernforschungsanlage Jülich ; 469) PB - Zentralbibliothek d. Kernforschungsanlage CY - Jülich ER - TY - JOUR A1 - Klinge, Uwe A1 - Wilke, Ralf A1 - Mühl, Thomas T1 - Auswahl der Herniennetze nach der “effektiven Porosität” - warum das Gewicht weniger wichtig ist JF - Chirurgische Allgemeine : CHAZ ; Zeitung für Klinik und Praxis Y1 - 2012 SN - 1615-5378 VL - 13 IS - 12 SP - 297 EP - 301 PB - Kaden CY - Mannheim ER - TY - JOUR A1 - Kern, Alexander A1 - Schelthoff, Christof T1 - Auswahl von Blitzschutzmassnahmen nach DIN EN 623305 (VDE 0185-305-x) JF - etz Elektrotechnik und Automation. 127 (2007), H. 8 Y1 - 2007 SN - 0948-7387 N1 - in der Bibliothek unter den Signaturen : 23 Z 133 und 63 ZS 035 vorhanden SP - 83 EP - 90 ER - TY - CHAP A1 - Eggert, Mathias A1 - Moulen, Tobias ED - D'Onofrio, Sara ED - Meinhardt, Stefan T1 - Auswahl von Geschäftsprozessen zur Anwendung von Robotic Process Automation – Vergleich relevanter Kriterien aus Theorie und Praxis T2 - Robotik in der Wirtschaftsinformatik N2 - Die Auswahl der passenden Geschäftsprozesse für eine Automatisierung mittels Robotic Process Automation (RPA) ist für den Erfolg von RPA-Projekten entscheidend. Das vorliegende Kapitel liefert dafür Selektionskriterien, die aus einer qualitativen Studie mit elf interviewten RPA-Experten aus dem Versicherungsumfeld resultieren. Das Ergebnis umfasst eine gewichtete Liste von sieben Dimensionen und 51 Prozesskriterien, welche die Automatisierung mit Softwarerobotern begünstigen beziehungsweise deren Nichterfüllung eine Umsetzung erschweren oder sogar verhindern. Die drei wichtigsten Kriterien zur Auswahl von Geschäftsprozessen für die Automatisierung mittels RPA umfassen die Entlastung der an dem Prozess mitwirkenden Mitarbeiter (Arbeitnehmerentlastung), die Ausführbarkeit des Prozesses mittels Regeln (Regelbasierte Prozessteuerung) sowie ein positiver Kosten-Nutzen-Vergleich. Auf diesen Ergebnissen aufbauend wird ein Vergleich mit den bereits bekannten Selektionskriterien aus der Literatur erstellt und diskutiert. Praktiker können die Ergebnisse verwenden, um eine systematische Auswahl von RPA-relevanten Prozessen vorzunehmen. Aus wissenschaftlicher Perspektive stellen die Ergebnisse eine Grundlage zur Erklärung des Erfolgs und Misserfolgs von RPA-Projekten dar. KW - Experteninterviews KW - Prozessauswahl KW - Selektionskriterien KW - Prozessverbesserung KW - Prozessautomatisierung KW - Robotic Process Automation Y1 - 2023 SN - 978-3-658-39620-6 (Print) SN - 978-3-658-39621-3 (Online) N1 - Vollständig überarbeiteter und erweiterter Beitrag basierend auf Eggert M, Moulen T (2020) Selektion von Geschäftsprozessen zur Anwendung von Robotic Process Automation am Beispiel einer Versicherung, 57(5):1150–1162 SP - 107 EP - 129 PB - Springer Vieweg CY - Wiesbaden ER - TY - JOUR A1 - Grundmann, Reinhard A1 - Bommes, Leonard A1 - Dieter, Reinartz T1 - Auswahl, Bemessung und Beurteilung eines Radialventilators hohen Wirkungsgrades - Teil 1 JF - HLH - Zeitschrift für Heizung, Lüftung, Klimatechnik, Haustechnik. 49 (1998), H. 5 Y1 - 1998 SN - 0017-9906 SP - 28 EP - 37 ER - TY - JOUR A1 - Grundmann, Reinhard A1 - Bommes, Leonard A1 - Reinartz, Dieter T1 - Auswahl, Bemessung und Beurteilung eines Radialventilators hohen Wirkungsgrades - Teil 2 JF - HLH - Zeitschrift für Heizung, Lüftung, Klimatechnik, Haustechnik. 49 (1998), H. 7 Y1 - 1998 SN - 0017-9906 SP - 44 EP - 50 ER - TY - JOUR A1 - Heuermann, Holger A1 - Stolle, Reinhard A1 - Schiek, Burkhard T1 - Auswertemethoden zur Praezisions-Entfernungsmessung mit FMCW-Systemen und deren Anwendung im Mikrowellenbereich JF - tm - Technisches Messen. 62. 1995 (1995), H. 2 Y1 - 1995 SP - 66 EP - 73 ER - TY - JOUR A1 - Alt, Helmut T1 - Auswertung von Belastungskennlinien JF - Elektrizitätswirtschaft Y1 - 1983 SN - 0013-5496 VL - Bd. 82 SP - 208 EP - 210 ER - TY - JOUR A1 - Sparla, Peter A1 - Kampmann, G. A1 - Wüller, Herbert T1 - Auswertung von EDM-Kalibrierungen mit unterstützendem robustem Schätzer JF - BDVI-Forum : Zeitschr. d. Bundes der Öffentlich Bestellten Vermessungsingenieure e.V (1986) Y1 - 1986 SP - 336 EP - 341 ER - TY - JOUR A1 - Alt, Helmut T1 - Auswertung von Prüfungsergebnissen auf elektronischen Rechenanlagen JF - Angewandte Informatik Y1 - 1974 SN - 0013-5704 VL - 16 IS - 5 SP - 219 EP - 222 PB - Vieweg CY - Braunschweig ER - TY - JOUR A1 - Büdenbender, Martin T1 - Auswirkungen der europäischen Energiepolitik auf den deutschen Atomausstieg JF - Zeitschrift für Energiewirtschaft N2 - Nach der Bundestagswahl am 27. September 2009 steht der Atomausstieg in Deutschland wieder ganz oben auf der politischen Agenda. Eine aktuelle Bestandsaufnahme aller ma\geblichen Argumente erscheint somit zwingend notwendig. Dabei sollte der Blickwinkel nicht national beschränkt bleiben, sondern vor allem der Einfluss der europäischen Dimension dieser Thematik miteinbezogen werden. Auf europäischer Ebene zeigt sich eine Position zu Gunsten der Kernenergie. Unter den 27 EU-Staaten findet gerade eine Renaissance der Atomkraft statt. Die drei europäischen Organe befürworten den umfangreichen Einsatz der Kernenergie als langfristigen Bestandteil des Energieträgermix. Deutschland gehört mit seinem Beschluss zum Atomausstieg einer Minderheit an. Als Teil eines immer stärker zusammen wachsenden und letztendlich vollständig integrierten europäischen Strommarktes wird Deutschland langfristig stets mit Atomstrom versorgt werden. Dies gilt losgelöst von dem Einsatz von Kernkraftwerken im Inland. Eine Abschaltung der Anlagen führt damit nicht zur Zielerreichung der Atomkraftgegner, sondern lediglich zu zusätzlichen energietechnischen Herausforderungen bei der Sicherstellung der deutschen Stromversorgung. Der deutsche Atomausstieg sollte aus diesem Grund von der neuen Bundesregierung zurück genommen werden. Y1 - 2009 SN - 1866-2765 U6 - https://doi.org/10.1007/s12398-009-0039-4 VL - 33 IS - 4 SP - 341 EP - 350 PB - Vieweg CY - Wiesbaden ER - TY - JOUR A1 - Schlamann, M. A1 - Yoon, M.-S. A1 - Maderwald, S. A1 - Pietrzyk, T. A1 - Bitz, Andreas A1 - Gerwig, M. A1 - Forsting, M. A1 - Ladd, S. C. A1 - Ladd, M. E. A1 - Kastrup, O. T1 - Auswirkungen der Magnetresonanztomografie auf die Elektrophysiologie des motorischen Kortex: eine Studie mit transkranieller Magnetstimulation T1 - Effects of MRI on the electrophysiology of the motor cortex: a TMS study JF - RöFo - Fortschritte auf dem Giebiet der Röntgenstrahlen und der bildgebenden Verfahren Y1 - 2009 U6 - https://doi.org/10.1055/s-0028-1109038 SN - 1438-9029 VL - 181 IS - 3 SP - 215 EP - 219 PB - Thieme CY - Stuttgart ER - TY - JOUR A1 - Kern, Alexander A1 - Kaiser, Ludwig T1 - Auswirkungen des EMVG auf leittechnische Einrichtungen in großflächigen Industrieanlagen / von Ludwig Kaiser ; Alexander Kern JF - ETZ : Elektrotechnik + Automation. 116 (1995), H. 9 Y1 - 1995 SN - 0170-1711 N1 - 2. ISSN: 0948-7387 ; In der Bibliothek unter 23 Z 133 (Eupener Str.) und 63 ZS 035 (Jülich) vorhanden. SP - 16 EP - 18 ER - TY - BOOK A1 - Büdenbender, Martin T1 - Auswirkungen des europäischen CO2-Handelssystems auf Stromerzeugungsinvestitionen - mögliche Ausgestaltung des Systems ab 2013 T3 - Düsseldorfer Schriften zum Energie- und Kartellrecht ; Bd. 13 N2 - Zahlreiche Einflussfaktoren haben in den vergangenen Jahren das Gesicht der Elektrizitätsmärkte stark verändert. Hierzu zählen vor allem die Einführung der ökonomischen Gesetze des Wettbewerbsmarktes durch die Liberalisierung sowie die nun kostenpflichtige Berücksichtigung des bei der Stromerzeugung hervorgerufenen CO2-Ausstoßes durch die Einführung des europäischen Emissionshandelssystems (EUTS). Die Folgen dieses Veränderungsprozesses lassen sich auf Grund der langen Investitionszyklen im Kraftwerksbau bisher nur unvollständig überblicken. Dies ist insbesondere im Hinblick auf die Versorgungssicherheit als Teil des energiewirtschaftlichen Zieldreiecks des § 1 EnWG von großer Bedeutung. Dazu zählt insbesondere, ob die Versorgungssicherheit in Deutschland bei gegenwärtigem Marktdesign auch dauerhaft gewährleistet sein wird. Es stellt sich heraus, dass es im Bereich der Spitzenlastkraftwerke zu Investitionen in gesamtwirtschaftlich zu geringen Umfang kommen kann. Dieses Investitionsdilemma beruht auf einem externen Effekt, der durch die aktuelle Ausgestaltung des deutschen Schadenersatzrechtes entsteht. Hierdurch ist die sichere Stromversorgung in Zeiten hoher Last potenziell gefährdet. Um die Wirkungen des Investitionsdilemmas abzumildern oder ganz zu beseitigen sind verschiedene Investitionsanreize durch entsprechende Ausgestaltung des EUTS denkbar. Diese werden im Einzelnen analysiert. KW - Elektrizitätserzeugung KW - Investitionsentscheidung KW - Umweltzertifikathandel KW - Emissionshandelssystem Y1 - 2009 SN - 9783942370318 PB - etv Energieverlag CY - Essen ER - TY - JOUR A1 - Benzel, Ute A1 - Linzbach, Meike T1 - Auswirkungen des Forderungsverzichtes – Steuerliche Belastung und Beeinflussung der Steuerquote JF - Deutsches Steuerrecht : DStR ; Wochenschrift & umfassende Datenbank für Steuerberater ; Steuerrecht, Wirtschaftsrecht, Betriebswirtschaft, Beruf ; Organ der Bundessteuerberaterkammer Y1 - 2009 SN - 0012-1347 ; 0949-7676 N1 - Printausg. in der Bibliothek vorhanden: 43 Z 451 VL - Jg. 47 IS - H. 31 SP - 1599 EP - 1602 PB - Beck CY - München ER - TY - JOUR A1 - Olbertz, Klaus T1 - Auswirkungen des neuen Entgelttransparenzgesetzes - Viel Aufwand für Unternehmen, wenig Greifbares für Arbeitnehmer JF - NWB - Steuer- und Wirtschaftsrecht Y1 - 2018 SN - 1860-9449 IS - 40 SP - 3068 EP - 3075 ER - TY - JOUR A1 - Schwabedal, Justus T. C. A1 - Sippel, Daniel A1 - Brandt, Moritz D. A1 - Bialonski, Stephan T1 - Automated Classification of Sleep Stages and EEG Artifacts in Mice with Deep Learning N2 - Sleep scoring is a necessary and time-consuming task in sleep studies. In animal models (such as mice) or in humans, automating this tedious process promises to facilitate long-term studies and to promote sleep biology as a data-driven f ield. We introduce a deep neural network model that is able to predict different states of consciousness (Wake, Non-REM, REM) in mice from EEG and EMG recordings with excellent scoring results for out-of-sample data. Predictions are made on epochs of 4 seconds length, and epochs are classified as artifactfree or not. The model architecture draws on recent advances in deep learning and in convolutional neural networks research. In contrast to previous approaches towards automated sleep scoring, our model does not rely on manually defined features of the data but learns predictive features automatically. We expect deep learning models like ours to become widely applied in different fields, automating many repetitive cognitive tasks that were previously difficult to tackle. Y1 - 2018 U6 - https://doi.org/10.48550/arXiv.1809.08443 ER - TY - CHAP A1 - Veettil, Yadu Krishna Morassery A1 - Rakshit, Shantam A1 - Schopen, Oliver A1 - Kemper, Hans A1 - Esch, Thomas A1 - Shabani, Bahman ED - Bin Abdollah, Mohd Fadzli ED - Amiruddin, Hilmi ED - Singh, Amrik Singh Phuman ED - Munir, Fudhail Abdul ED - Ibrahim, Asriana T1 - Automated Control System Strategies to Ensure Safety of PEM Fuel Cells Using Kalman Filters T2 - Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia N2 - Having well-defined control strategies for fuel cells, that can efficiently detect errors and take corrective action is critically important for safety in all applications, and especially so in aviation. The algorithms not only ensure operator safety by monitoring the fuel cell and connected components, but also contribute to extending the health of the fuel cell, its durability and safe operation over its lifetime. While sensors are used to provide peripheral data surrounding the fuel cell, the internal states of the fuel cell cannot be directly measured. To overcome this restriction, Kalman Filter has been implemented as an internal state observer. Other safety conditions are evaluated using real-time data from every connected sensor and corrective actions automatically take place to ensure safety. The algorithms discussed in this paper have been validated thorough Model-in-the-Loop (MiL) tests as well as practical validation at a dedicated test bench. KW - control system KW - PEM fuel cells KW - Kalman filter Y1 - 2022 SN - 978-981-19-3178-9 SN - 978-981-19-3179-6 (E-Book) U6 - https://doi.org/10.1007/978-981-19-3179-6_55 SN - 2195-4356 N1 - 7th International Conference and Exhibition on Sustainable Energy and Advanced Material (ICE-SEAM 2021), Universiti Teknikal Malaysia Melaka (UTeM), Malaysia, in association with the Universitas Sebelas Maret (UNS), Indonesia, 23 November 2021 SP - 296 EP - 299 PB - Springer Nature CY - Singapore ER - TY - CHAP A1 - Ayed, Anis Haj A1 - Striegan, Constantin J. D. A1 - Kusterer, Karsten A1 - Funke, Harald A1 - Kazari, M. A1 - Horikawa, Atsushi A1 - Okada, Kunio T1 - Automated design space exploration of the hydrogen fueled "Micromix" combustor technology N2 - Combined with the use of renewable energy sources for its production, Hydrogen represents a possible alternative gas turbine fuel for future low emission power generation. Due to its different physical properties compared to other fuels such as natural gas, well established gas turbine combustion systems cannot be directly applied for Dry Low NOx (DLN) Hydrogen combustion. This makes the development of new combustion technologies an essential and challenging task for the future of hydrogen fueled gas turbines. The newly developed and successfully tested “DLN Micromix” combustion technology offers a great potential to burn hydrogen in gas turbines at very low NOx emissions. Aiming to further develop an existing burner design in terms of increased energy density, a redesign is required in order to stabilise the flames at higher mass flows and to maintain low emission levels. For this purpose, a systematic design exploration has been carried out with the support of CFD and optimisation tools to identify the interactions of geometrical and design parameters on the combustor performance. Aerodynamic effects as well as flame and emission formation are observed and understood time- and cost-efficiently. Correlations between single geometric values, the pressure drop of the burner and NOx production have been identified as a result. This numeric methodology helps to reduce the effort of manufacturing and testing to few designs for single validation campaigns, in order to confirm the flame stability and NOx emissions in a wider operating condition field. Y1 - 2017 N1 - Proceedings of the 1st Global Power and Propulsion Forum GPPF 2017, Jan 16-18, 2017, Zurich, Switzerland SP - 1 EP - 8 ER - TY - JOUR A1 - Gorzalka, Philip A1 - Schmiedt, Jacob Estevam A1 - Schorn, Christian T1 - Automated Generation of an Energy Simulation Model for an Existing Building from UAV Imagery JF - Buildings N2 - An approach to automatically generate a dynamic energy simulation model in Modelica for a single existing building is presented. It aims at collecting data about the status quo in the preparation of energy retrofits with low effort and costs. The proposed method starts from a polygon model of the outer building envelope obtained from photogrammetrically generated point clouds. The open-source tools TEASER and AixLib are used for data enrichment and model generation. A case study was conducted on a single-family house. The resulting model can accurately reproduce the internal air temperatures during synthetical heating up and cooling down. Modelled and measured whole building heat transfer coefficients (HTC) agree within a 12% range. A sensitivity analysis emphasises the importance of accurate window characterisations and justifies the use of a very simplified interior geometry. Uncertainties arising from the use of archetype U-values are estimated by comparing different typologies, with best- and worst-case estimates showing differences in pre-retrofit heat demand of about ±20% to the average; however, as the assumptions made are permitted by some national standards, the method is already close to practical applicability and opens up a path to quickly estimate possible financial and energy savings after refurbishment. KW - Modelica KW - heat transfer coefficient KW - heat demand KW - building energy modelling KW - building energy simulation Y1 - 2021 U6 - https://doi.org/10.3390/buildings11090380 SN - 2075-5309 N1 - This article belongs to the Special Issue "Application of Computer Technology in Buildings" VL - 11 IS - 9 PB - MDPI CY - Basel ER - TY - JOUR A1 - Neu, Eugen A1 - Janser, Frank A1 - Khatibi, Akbar A. A1 - Orifici, Adrian C. T1 - Automated modal parameter-based anomaly detection under varying wind excitation JF - Structural Health Monitoring N2 - Wind-induced operational variability is one of the major challenges for structural health monitoring of slender engineering structures like aircraft wings or wind turbine blades. Damage sensitive features often show an even bigger sensitivity to operational variability. In this study a composite cantilever was subjected to multiple mass configurations, velocities and angles of attack in a controlled wind tunnel environment. A small-scale impact damage was introduced to the specimen and the structural response measurements were repeated. The proposed damage detection methodology is based on automated operational modal analysis. A novel baseline preparation procedure is described that reduces the amount of user interaction to the provision of a single consistency threshold. The procedure starts with an indeterminate number of operational modal analysis identifications from a large number of datasets and returns a complete baseline matrix of natural frequencies and damping ratios that is suitable for subsequent anomaly detection. Mahalanobis distance-based anomaly detection is then applied to successfully detect the damage under varying severities of operational variability and with various degrees of knowledge about the present operational conditions. The damage detection capabilities of the proposed methodology were found to be excellent under varying velocities and angles of attack. Damage detection was less successful under joint mass and wind variability but could be significantly improved through the provision of the currently encountered operational conditions. Y1 - 2016 U6 - https://doi.org/10.1177/1475921716665803 SN - 1475-9217 VL - 15 IS - 6 SP - 1 EP - 20 PB - Sage CY - London ER - TY - THES A1 - Pfaff, Raphael T1 - Automated processing of the ISL Doppler images Y1 - 2007 N1 - Hagen, Fernuniv., Bachelorarbeit, 2007 ER - TY - CHAP A1 - Sildatke, Michael A1 - Karwanni, Hendrik A1 - Kraft, Bodo A1 - Schmidts, Oliver A1 - Zündorf, Albert T1 - Automated Software Quality Monitoring in Research Collaboration Projects T2 - ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops N2 - In collaborative research projects, both researchers and practitioners work together solving business-critical challenges. These projects often deal with ETL processes, in which humans extract information from non-machine-readable documents by hand. AI-based machine learning models can help to solve this problem. Since machine learning approaches are not deterministic, their quality of output may decrease over time. This fact leads to an overall quality loss of the application which embeds machine learning models. Hence, the software qualities in development and production may differ. Machine learning models are black boxes. That makes practitioners skeptical and increases the inhibition threshold for early productive use of research prototypes. Continuous monitoring of software quality in production offers an early response capability on quality loss and encourages the use of machine learning approaches. Furthermore, experts have to ensure that they integrate possible new inputs into the model training as quickly as possible. In this paper, we introduce an architecture pattern with a reference implementation that extends the concept of Metrics Driven Research Collaboration with an automated software quality monitoring in productive use and a possibility to auto-generate new test data coming from processed documents in production. Through automated monitoring of the software quality and auto-generated test data, this approach ensures that the software quality meets and keeps requested thresholds in productive use, even during further continuous deployment and changing input data. Y1 - 2020 U6 - https://doi.org/10.1145/3387940.3391478 N1 - ICSE '20: 42nd International Conference on Software Engineering, Seoul, Republic of Korea, 27 June 2020 - 19 July 2020 SP - 603 EP - 610 PB - IEEE CY - New York, NY ER - TY - JOUR A1 - Schmitz, Günter A1 - Oligschläger, U. A1 - Eifler, G. A1 - Lechner, H. T1 - Automated System for Optimized Calibration of Engine Management Systems Y1 - 1994 N1 - SAE International Congress and Exposition, Detroit, Feb. 28 - March 3 ; SAE- Paper-No.: 940151 ; SP - 61 EP - 64 ER - TY - THES A1 - Vogt, Linda T1 - Bambus als Baumaterial : eine nachhaltige Alternative zu herkömmlichen Rohstoffen? N2 - "Das Editorial greift die Thematik der aktuellen Klimakrise auf und beleuchtet diese im Bereich des nachhaltigen Bauens. Denn durch das stetige Wachstum der menschlichen Bevölkerung in Kombination mit dem Anstieg des Pro-Kopf-Verbrauchs werden globale Ressourcen immer stärker belastet. Ziel der Arbeit ist es, die aktuelle Situation des Klimawandels aus einer Perspektive zu betrachten, der sich die meisten nicht bewusst sind. Denn besonders das Bauwesen trägt einen erheblichen Anteil zum Klimawandel bei. In der Publikation werden Texte zum Thema Klimawandel und nachhaltiges Bauen behandelt sowie fotografische Anwendungsbeispiele im Bereich der Bambus-Architektur gezeigt. Das Projekt präsentiert Lösungsansätze, wie herkömmliche Rohstoffe durch verarbeiteten Bambus ergänzt bzw. ersetzt werden können. Dadurch kann ein entscheidender Beitrag zur Bekämpfung des Klimawandels geleistet werden. Bambus bietet dahingehend viele Möglichkeiten. Bei richtiger Verarbeitung vereint er viele der geforderten Ansprüche nachhaltigen Bauens. Der Rohstoff ist stark und flexibel zugleich. Er bindet Kohlenstoff, reinigt kontaminierte Böden, beugt Erosionen vor und weist eine nahezu negative CO2-Bilanz auf. Wie kann es gelingen, diesen Rohstoff in westlichen Ländern als Baumaterial zu integrieren?" KW - Klimakrise KW - Nachhaltigkeit KW - nachhaltiges Bauen KW - Urbanisierung KW - Bambus Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Müller-Veggian, Mattea A1 - Bochev, B. A1 - Lieder, R. M. A1 - Morek, T. T1 - Band crossing and blocking in side bands of ¹⁸⁰,¹⁸² Os JF - Frühjahrstagung ... des Fachausschusses Kernphysik und Hochenergiephysik der DPG (Sektion A: Kernphysik) / Deutsche Physikalische Gesellschaft (1982) Y1 - 1982 N1 - Verhandlungen der Deutschen Physikalischen Gesellschaft ; 1982=6.R.17,6 SP - 1273 ER - TY - JOUR A1 - Förster, Arnold A1 - Ohler, C. A1 - Moers, J. T1 - Band offsets at heavily strained III - V interfaces / C. Ohler ; A. Förster ; J. Moers... JF - Journal of Physics D: Applied Physics. 30 (1997), H. 10 Y1 - 1997 SN - 0022-3727 N1 - ISSN der E-Ausg.: 1361-6463 SP - 1436 EP - 1441 ER - TY - JOUR A1 - Müller-Veggian, Mattea A1 - Beuscher, H. A1 - Neskakis, A A1 - Gono, Y. T1 - Band structure in ¹⁹⁰,¹⁹² Au JF - Annual report 1977 / Institut für Kernphysik Kernforschungsanlage Jülich Y1 - 1978 N1 - Spezielle Berichte der Kernforschungsanlage Jülich ; 15 SP - 46 EP - 47 PB - Verlag des Forschungszentrums Jülich CY - Jülich ER - TY - JOUR A1 - Müller-Veggian, Mattea A1 - Beuscher, H. A1 - Neskakis, A A1 - Gono, Y. T1 - Band structure in ¹⁹⁰,¹⁹² Au JF - Frühjahrstagung ... des Fachausschusses Kernphysik und Hochenergiephysik der DPG (Sektion A: Kernphysik) / Deutsche Physikalische Gesellschaft (1978) Y1 - 1978 SP - 796 PB - Physik-Verlag CY - Weinheim ER - TY - JOUR A1 - Müller-Veggian, Mattea A1 - Neskakis, A. A1 - Beuscher, H. A1 - Haenni, D. R. T1 - Band structure in ¹⁹⁴ Au JF - Annual report 1978 / Kernforschungsanlage Jülich Institut für Kernphysik / Hrsg.: A. Fässler. - (Spezielle Berichte der Kernforschungsanlage Jülich ; 36) Y1 - 1979 SP - 36 PB - Kernforschungsanlage CY - Jülich ER - TY - JOUR A1 - Förster, Arnold A1 - Ohler, C. A1 - Daniels, C. T1 - Barrier height at clean Au/InAs(100) interfaces / C. Ohler ; C. Daniels ; A. Förster ... JF - Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures. 15 (1997), H. 3 Y1 - 1997 SN - 0169-4332 SP - 702 EP - 706 ER - TY - CHAP A1 - Bitz, Andreas A1 - Alaydrus, M. A1 - Streckert, J. A1 - Hansen, V.W. T1 - Base station antennas embedded in complex environments: rf exposure in controlled areas T2 - 23rd BEMS Annual Meeting, St. Paul, Minnesota, USA, 49-50, June 2001 Y1 - 2001 SP - 49 EP - 50 PB - Bioelectromagnetics Society CY - Frederick, MD ER - TY - CHAP A1 - Frantz, Cathy A1 - Binder, Matthias A1 - Busch, Konrad A1 - Ebert, Miriam A1 - Heinrich, Andreas A1 - Kaczmarkiewicz, Nadine A1 - Schlögl-Knothe, Bärbel A1 - Kunze, Tobias A1 - Schuhbauer, Christian A1 - Stetka, Markus A1 - Schwager, Christian A1 - Spiegel, Michael A1 - Teixeira Boura, Cristiano José A1 - Bauer, Thomas A1 - Bonk, Alexander A1 - Eisen, Stefan A1 - Funck, Bernhard T1 - Basic Engineering of a High Performance Molten Salt Tower Receiver System T2 - AIP Conference Proceedings N2 - The production of dispatchable renewable energy will be one of the most important key factors of the future energy supply. Concentrated solar power (CSP) plants operated with molten salt as heat transfer and storage media are one opportunity to meet this challenge. Due to the high concentration factor of the solar tower technology the maximum process temperature can be further increased which ultimately decreases the levelized costs of electricity of the technology (LCOE). The development of an improved tubular molten salt receiver for the next generation of molten salt solar tower plants is the aim of this work. The receiver is designed for a receiver outlet temperature up to 600 °C. Together with a complete molten salt system, the receiver will be integrated into the Multi-Focus-Tower (MFT) in Jülich (Germany). The paper describes the basic engineering of the receiver, the molten salt tower system and a laboratory corrosion setup. Y1 - 2020 U6 - https://doi.org/10.1063/5.0085895 N1 - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September – 2 October 2020, Freiburg, Germany SP - 1 EP - 10 ER - TY - JOUR A1 - Zastrow, Udo T1 - Basic geometrical singularities in plane-elasticity and plate-bending problems JF - International Journal of Solids and Structures. 21 (1985), H. 10 Y1 - 1985 SN - 0020-7683 SP - 1047 EP - 1067 ER - TY - CHAP A1 - Abbas, Karim A1 - Thurn, Laura A1 - Kessler, Julia A1 - Eichler, Fabian T1 - Basic research of the consideration of additive manufactured lattice structures under thermoand fluid dynamic loads T2 - Modern technologies in manufacturing (MTeM 2019) Y1 - 2019 U6 - https://doi.org/10.1051/matecconf/201929901009 N1 - MATEC Web of Conferences 299; MTeM 2019 VL - 299 IS - Article 01009 ER - TY - CHAP A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas A1 - Abbas, Karim T1 - Basic research on lattice structures focused on the reliance of the cross sectional area and additional coatings T2 - The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 – CoSME’16 Y1 - 2017 U6 - https://doi.org/10.1051/matecconf/20179403008 N1 - MATEC Web Conf. Vol 94, 2017, 03008 MATEC Web of Conferences 94, 03008 (2017) ET - Vol. 94 ER - TY - CHAP A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas T1 - Basic research on lattice structures focused on the strut shape and welding beads T2 - Physics Procedia Y1 - 2016 U6 - https://doi.org/10.1016/j.phpro.2016.08.086 SN - 1875-3884 N1 - Laser Assisted Net Shape Engineering 9th International Conference on Photonic Technologies Proceedings of the LANE 2016 VL - Vol. 83 SP - 833 EP - 838 ER - TY - JOUR A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas A1 - Abbas, Karim T1 - Basic Research on Lattice Structures Focused on the Tensile Strength JF - Applied Mechanics and Materials Y1 - 2015 U6 - https://doi.org/10.4028/www.scientific.net/AMM.808.193 SN - 1662-7482 N1 - MTeM ; October 14-16, 2015, Cluj-Napoca, Romania VL - Vol. 808 SP - 193 EP - 198 PB - Trans Tech Publications CY - Bäch ER - TY - JOUR A1 - Selmer, Thorsten A1 - Jennemann, Richard A1 - Bauer, Bernhard L. A1 - Bertalanffy, Helmut T1 - Basidiolipids from Agaricus are novel immune adjuvants / Jennemann, R. ; Bauer, BL. ; Bertalanffy, H. ; Selmer, T. ; Wiegandt, H. JF - Immunobiology. 200 (1999), H. 2 Y1 - 1999 SN - 0171-2985 N1 - PMID: 10416134 SP - 277 EP - 289 ER - TY - CHAP A1 - Staat, Manfred A1 - Heitzer, M. T1 - Basis reduction technique for limit and shakedown problems T2 - Numerical Methods for Limit and Shakedown Analysis. Deterministic and Probabilistic Approach. NIC Series Vol. 15 / Ed. by Staat, M.; Heitzer, M. Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:0001-2018112115 SN - 3-00-010001-6 SP - 1 EP - 55 PB - John von Neumann Institute for Computing (NIC) CY - Jülich ER - TY - JOUR A1 - Biselli, Manfred A1 - Thömmes, J. A1 - Kula, M.-R. A1 - Wandrey, Christian T1 - Batch kinetic data of hybridoma growth and productivity as a basis for the simulation of antibody production in various culture systems / Thömmes, J. ; Biselli, M. ; Kula, M.-R. ; Wandrey, C. JF - Animal cell technology : products of today, prospects for tomorrow ; ESACT, European Society for Animal Cell Technology, the 12th meeting / Ed. R. E. Spier Y1 - 1994 SN - 0750618450 N1 - Meeting / European Society for Animal Cell Technology ; 12 SP - 513 EP - 517 PB - Butterworth-Heinemann CY - Oxford ER - TY - JOUR A1 - Hagemann, Hans-Jürgen A1 - Ihrig, H. T1 - BaTiO3 dotiert mit 3d-Ionen: Valenzen, Leerstellen und ihre Auswirkungen. Hagemann, H. J.; Ihrig, H. JF - Philips - Unsere Forschung in Deutschland / Hrsg.: Philips Forschungslaboratorium GmbH Aachen und Hamburg. 3 (1980) Y1 - 1980 SP - 249 EP - 252 ER - TY - GEN A1 - Wulfhorst, H. A1 - Merseburg, J. A1 - Tippkötter, Nils T1 - Batteriekomponenten aus nachwachsenden Rohstoffen T2 - Chemie Ingenieur Technik N2 - In diesem Beitrag geht es um die Integration von Stoffströmen einer Lignocellulose-Bioraffinerie in Verfahren zur Batterieherstellung. Pflanzliche Reststoffe aus der Biokraftstoffherstellung wie Lignin sollen zur Herstellung neuer Batteriematerialien verwendet werden. Hierbei wird das Lignin als Matrix für die vorgraphitischen C-haltigen Einlagerungsverbindungen in den Elektroden genutzt. Die Si-C-Komposite werden durch das Einbetten von Si in eine Ligninmatrix mit anschließender Carbonisierung hergestellt. Das Lignin hierfür wird durch die sequentielle hydrothermale Vorbehandlung von Buchenholz bei variablen Bedingungen gewonnen und mit Si-Nanopartikel sowie als Referenz ohne Si-Nanopartikel gefällt. Die Ergebnisse zeigen, dass die sequenzielle Vorbehandlung höhere Ausbeuten im Vergleich zum LHW- oder Organosolv-Aufschluss liefert. Um eine Anode herzustellen, wurde das resultierende Si–C-Kompositmaterial carbonisiert, auf einen Stromsammler aufgetragen und elektro-chemisch charakterisiert. Der Einfluss der Vorbehandlungsschritte auf den Herstellungsprozess und die ökonomische Bewertung des untersuchten Bioraffinerie-Prozesses wurde mithilfe eines Stoffstrommodells analysiert. Y1 - 2016 U6 - https://doi.org/10.1002/cite.201650333 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2016 und 32. DECHEMA-Jahrestagung der Biotechnologen 2016, 12. - 15. September 2016, Eurogress Aachen VL - 88 IS - 9 SP - 1234 EP - 1235 PB - Wiley-VCH CY - Weinheim ER - TY - BOOK A1 - Wosnitza, Franz T1 - Bau eines HF-Empfangsteiles, Bild-Ton-ZF-Verstärkers und Demodulators, sowie eines Bildträgertonempfangsteiles für Schmalbandfernsehen für den ATV-Fernsehumsetzer DK 0 HJ / Betreuer: Erich Vogelsang Y1 - 1976 N1 - Aachen, Fachhochschule, Diplomarbeit 1976 ER - TY - JOUR A1 - Biener, Ernst A1 - Wernhoff, T. A1 - Bökers, H. A1 - Sasse, T. T1 - Bau und 7-jähriger Betrieb eines Dichtungskontrollsystems sowie Durchführung von Bewässerungsmaßnahmen auf der Deponie Wesuwe / Wernhoff, T. ; Bökers, H. ; Biener, E. ; Sasse, T. JF - Tagungsband / 3. Praxistagung Deponie 2008 : Zwischenlager - Deponien - Nachsorge ; 2. und 3. Dezember 2008 / Wasteconsult International. Matthias Kühle-Weidemeier (Hrsg.) Y1 - 2008 SN - 978-3-86727-801-0 N1 - Praxistagung Deponie <3, 2008, Hannover> SP - 157 EP - 174 PB - Cuvillier CY - Göttingen ER - TY - CHAP A1 - Krause, Thomas A1 - Ulke, Bernd ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Bauabrechnung und Mengenermittlung T2 - Zahlentafeln für den Baubetrieb N2 - n diesem Kapitel werden die Abrechnungsvorschriften wichtiger ATV kurz, aber umfassend zusammengestellt. Einigen Abrechnungsbestimmungen für Einzelleistungen, die keine Nebenleistungen sind ((siehe DIN 18299 und Abschnitt 4 der jeweiligen ATV), sind mit aufgenommen worden; die ATV enthalten jedoch weitergehende Festlegungen über Nebenleistungen und Besondere Leistungen. Im Anschluss folgen Hinweise zu den Toleranzen im Hochbau sowie im Straßenbau. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - https://doi.org/10.1007/978-3-658-41330-9_7 SP - 333 EP - 397 PB - Springer Vieweg CY - Wiesbaden ER - TY - JOUR A1 - Krause, Thomas T1 - Bauabrechnung und Mengenermittlung JF - Zahlentafeln für den Baubetrieb / Hoffmann, Manfred ; Kuhlmann, Willy [Hrsg.]. 7., vollst. überarb. Aufl. Y1 - 2006 SN - 3-519-65220-X N1 - Kapitel 7 SP - 491 EP - 546 PB - Teubner CY - Wiesbaden ER - TY - CHAP A1 - Krause, Thomas T1 - Bauabrechnung und Mengenermittlung T2 - Übungsaufgaben und Berechnungen für den Baubetrieb Y1 - 2019 SN - 978-3-658-23127-9 U6 - https://doi.org/10.1007/978-3-658-23127-9_5 SP - 101 EP - 116 PB - Springer Vieweg CY - Wiesbaden ER -