TY - JOUR A1 - Kluczka, Sven A1 - Eckstein, Julian A1 - Alexopoulos, Spiros A1 - Vaeßen, Christiane A1 - Roeb, Martin T1 - Process simulation for solar steam and dry reforming JF - Energy procedia : Proceedings of the SolarPACES 2013 International Conference N2 - In co-operation with the German Aerospace Center, the Solar-Institut Jülich has been analyzing the different technologies that are available for methanol production from CO2 using solar energy. The aim of the project is to extract CO2 from industrial exhaust gases or directly from the atmosphere to recycle it by use of solar energy. Part of the study was the modeling and simulating of a methane reformer for the production of synthesis gas, which can be operated by solar or hybrid heat sources. The reformer has been simplified in such a way that the model is accurate and enables fast calculations. The developed pseudo-homogeneous one- dimensional model can be regarded as a kind of counter-current heat exchanger and is able to incorporate a steam reforming reaction as well as a dry reforming reaction. Y1 - 2014 U6 - https://doi.org/10.1016/j.egypro.2014.03.092 SN - 1876-6102 (E-Journal) VL - 49 SP - 850 EP - 859 PB - Elsevier CY - Amsterdam ER - TY - GEN A1 - Tippkötter, Nils A1 - Wasserscheid, P. T1 - Rapid-Prototyping-Strukturen für ressourceneffiziente Prozesse in Chemie und Biotechnologie T2 - Chemie Ingenieur Technik N2 - Die Teilefertigung durch Rapid Prototyping (RP) verkürzt den Weg von der Idee bis zum Produkt, wobei unter anderem Optimierungszyklen in geringer Zeit durchlaufen werden können. Ferner eröffnen neue Entwicklungen in diesem Bereich die Möglichkeit individueller Produktionsverfahren. Im Unterschied zur klassischen Fertigung von Prototypen wird beim RP mit additiver Schichtfertigung (Additive Layer Manufacturing, ALM) gearbeitet. Je nach Methode werden Flüssigkeiten oder Pulver nach Vorgaben eines 3D-Computermodells sequentiell aufgetragen. Diese Verfahren existieren seit ca. 25 Jahren, jedoch sind seit kurzem ausgesprochen günstige Geräte verfügbar, die Objekte mit Genauigkeiten bis 20 lm fertigen können. Das RP hat in klinischen Anwendungsgebieten bzw. im Bereich des Tissue Engineering bereits vielfach Einzug gefunden. Aber auch chemisch-biotechnologische Entwicklungen können von den Verfahren profitieren. So wurden Mikrofluidiksysteme und Bioreaktoren bereits erfolgreich durch RP gefertigt. Durch ALM ist ebenso die Herstellung von Reaktionseinheiten aus biokompatiblen Materialien wie ionotropen Gelen möglich. Ferner sind sehr komplexe Strukturierungen von Oberflächen im Nanometerbereich realisierbar, die für die Auftragung heterogener Katalysatoren oder auch Mikroorganismen eingesetzt werden können. Auch der Bereich Reaktoren- und Apparatebau kann von den Fortschritten in der additiven Fertigung profitieren. Verfahren wie selektives Laser- oder Elektronenstrahlschmelzen erlauben es, metallische Komponenten in nahezu beliebigen Geometrien zu fertigen. Somit können Strukturen verwirklicht werden, die mit konventionellen Fertigungstechniken nur sehr schwer oder überhauptnicht herstellbar wären. Durch Anwendung von rechnergestützter Modellierung können optimale Strukturen identifiziert und additiv gefertigt werden. Eine anschließende katalytische Funktionalisierung der Oberfläche ermöglicht die Herstellung strukturierter Reaktoren mit maßgeschneiderten Eigenschaften. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450451 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1369 EP - 1370 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Ögun, Celal Mohan A1 - Kling, Rainer A1 - Heuermann, Holger A1 - Gräser, Ulrich A1 - Schopp, Christoph T1 - Elektrodenlose quecksilberfreie Niederdrucklampen betrieben mit Mikrowellen T2 - Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband Y1 - 2014 PB - Nederlandse Stichting voor Verlichtingskunde CY - Ede ER - TY - CHAP A1 - Laack, Walter van T1 - Gefahren heutiger neurologischer Schlussfolgerungen für ethische Verantwortung T2 - Ethik und Moral in Staat, Wirtschaft und Gesellschaft : 5. Rotary-Tag, 14.-15.2.2014, Kleve Y1 - 2014 SN - 978-3-944011-21-9 SP - 98 EP - 114 PB - Edition Virgines CY - Lingen ER - TY - CHAP A1 - Ritz, Thomas A1 - Izquierdo Tello, César A1 - Damm, Sebastian T1 - Connecting a pedelec to the cloud as basis for gamification in multi modal mobility planning T2 - MobileCloud 2014 : 2nd IEEE International Conference on Mobile Cloud Computing, Services, and Engineering Oxford, United Kingdom 7-10 April 2014 Y1 - 2014 SN - 978-1-4799-2504-9 U6 - https://doi.org/10.1109/MobileCloud.2014.25 SP - 101 EP - 108 PB - IEEE Service Center CY - Piscataway, NJ ER - TY - JOUR A1 - Schusser, Sebastian A1 - Bäcker, Matthias A1 - Krischer, M. A1 - Wenzel, L. A1 - Leinhos, Marcel A1 - Poghossian, Arshak A1 - Biselli, Manfred A1 - Wagner, P. A1 - Schöning, Michael Josef T1 - Enzymatically catalyzed degradation of biodegradable polymers investigated by means of a semiconductor-based field-effect sensor JF - Procedia Engineering N2 - A semiconductor field-effect device has been used for an enzymatically catalyzed degradation of biopolymers for the first time. This novel technique is capable to monitor the degradation process of multiple samples in situ and in real-time. As model system, the degradation of the biopolymer poly(D, L-lactic acid) has been monitored in the degradation medium containing the enzyme lipase from Rhizomucor miehei. The obtained results demonstrate the potential of capacitive field-effect sensors for degradation studies of biodegradable polymers. KW - Field-effect sensor KW - enzymatic (bio)degradation KW - poly(d, l-lactic acid) KW - in-situ monitoring KW - impedance spectroscopy Y1 - 2014 U6 - https://doi.org/10.1016/j.proeng.2014.11.689 SN - 1877-7058 N1 - EUROSENSORS 2014 ; European Conference on Solid-State Transducers <28, 2014> VL - 87 SP - 1314 EP - 1317 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - Label-free sensing of biomolecules with field-effect devices for clinical applications JF - Electroanalysis N2 - Among the variety of transducer concepts proposed for label-free detection of biomolecules, the semiconductor field-effect device (FED) is one of the most attractive platforms. As medical techniques continue to progress towards diagnostic and therapies based on biomarkers, the ability of FEDs for a label-free, fast and real-time detection of multiple pathogenic and physiologically relevant molecules with high specificity and sensitivity offers very promising prospects for their application in point-of-care and personalized medicine for an early diagnosis and treatment of diseases. The presented paper reviews recent advances and current trends in research and development of different FEDs for label-free, direct electrical detection of charged biomolecules by their intrinsic molecular charge. The authors are mainly focusing on the detection of the DNA hybridization event, antibody-antigen affinity reaction as well as clinically relevant biomolecules such as cardiac and cancer biomarkers. Y1 - 2014 U6 - https://doi.org/10.1002/elan.201400073 SN - 1521-4109 (E-Journal); 1040-0397 (Print) VL - 26 IS - 6 SP - 1197 EP - 1213 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Leinhos, Marcel A1 - Schusser, Sebastian A1 - Bäcker, Matthias A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - Micromachined multi-parameter sensor chip for the control of polymer-degradation medium JF - Physica Status Solidi (A) : special issue on engineering and functional interfaces N2 - It is well known that the degradation environment can strongly influence the biodegradability and kinetics of biodegradation processes of polymers. Therefore, besides the monitoring of the degradation process, it is also necessary to control the medium in which the degradation takes place. In this work, a micromachined multi-parameter sensor chip for the control of the polymer-degradation medium has been developed. The chip combines a capacitive field-effect pH sensor, a four-electrode electrolyte-conductivity sensor and a thin-film Pt-temperature sensor. The results of characterization of individual sensors are presented. In addition, the multi-parameter sensor chip together with an impedimetric polymer-degradation sensor was simultaneously characterized in degradation solutions with different pH and electrolyte conductivity. The obtained results demonstrate the feasibility of the multi-parameter sensor chip for the control of the polymer-degradation medium. Y1 - 2014 U6 - https://doi.org/10.1002/pssa.201330364 SN - 1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print) VL - 211 IS - 6 SP - 1346 EP - 1351 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Huck, Christina A1 - Poghossian, Arshak A1 - Bäcker, Matthias A1 - Chaudhuri, S. A1 - Zander, W. A1 - Schubert, J. A1 - Begoyan, V. K. A1 - Buniatyan, V. V. A1 - Wagner, P. A1 - Schöning, Michael Josef T1 - Capacitively coupled electrolyte-conductivity sensor based on high-k material of barium strontium titanate JF - Sensors and actuators. B: Chemical Y1 - 2014 U6 - https://doi.org/10.1016/j.snb.2014.02.103 SN - 1873-3077 (E-Journal); 0925-4005 (Print) IS - 198 SP - 102 EP - 109 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Bäcker, Matthias A1 - Kramer, F. A1 - Huck, Christina A1 - Poghossian, Arshak A1 - Bratov, A. A1 - Abramova, N. A1 - Schöning, Michael Josef T1 - Planar and 3D interdigitated electrodes for biosensing applications: The impact of a dielectric barrier on the sensor properties JF - Physica Status Solidi (A) - Applications and Materials Science N2 - Planar and three-dimensional (3D) interdigitated electrodes (IDE) with electrode digits separated by an insulating barrier of different heights were electrochemically characterized and compared in terms of their sensing properties. Due to the impact of the surface resistance, both types of IDE structures display a non-linear behavior in low-ionic strength solutions. The experimental data were fitted to an electrical equivalent circuit and interpreted taking into account the surface-charge-governed properties. The effect of a charged polyelectrolyte layer electrostatically assembled onto the sensor surface on the surface resistance in solutions with different KCl concentration is studied. In case of the same electrode footprint, 3D-IDEs show a larger cell constant and a higher sensitivity to molecular adsorption than that of planar IDEs. The obtained results demonstrate the potential of 3D-IDEs as a new transducer structure for a direct label-free sensing of charged molecules. Y1 - 2014 U6 - https://doi.org/10.1002/pssa.201330416 SN - 1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print) VL - 211 IS - 6 SP - 1357 EP - 1363 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Moseley, Fiona A1 - Halamek, Jan A1 - Kramer, Friederike A1 - Poghossian, Arshak A1 - Schöning, Michael Josef A1 - Katz, Evgeny T1 - An enzyme-based reversible CNOT logic gate realized in a flow system JF - Analyst N2 - An enzyme system organized in a flow device was used to mimic a reversible Controlled NOT (CNOT) gate with two input and two output signals. Reversible conversion of NAD⁺ and NADH cofactors was used to perform a XOR logic operation, while biocatalytic hydrolysis of p-nitrophenyl phosphate resulted in an Identity operation working in parallel. The first biomolecular realization of a CNOT gate is promising for integration into complex biomolecular networks and future biosensor/biomedical applications. Y1 - 2014 U6 - https://doi.org/10.1039/C4AN00133H SN - 1364-5528 (E-Journal) ; 0003-2654 (Print) VL - 139 IS - 8 SP - 1839 EP - 1842 PB - Royal Society of Chemistry CY - Cambridge ER - TY - CHAP A1 - McInnes, Colin R. A1 - Bothmer, Volker A1 - Dachwald, Bernd A1 - Geppert, Ulrich R. M. E. A1 - Heiligers, Jeannette A1 - Hilgers, Alan A1 - Johnson, Les A1 - Macdonald, Malcolm A1 - Reinhard, Ruedeger A1 - Seboldt, Wolfgang A1 - Spietz, Peter T1 - Gossamer roadmap technology reference study for a Sub-L1 Space Weather Mission T2 - Advances in solar sailing N2 - A technology reference study for a displaced Lagrange point space weather mission is presented. The mission builds on previous concepts, but adopts a strong micro-spacecraft philosophy to deliver a low mass platform and payload which can be accommodated on the DLR/ESA Gossamer-3 technology demonstration mission. A direct escape from Geostationary Transfer Orbit is assumed with the sail deployed after the escape burn. The use of a miniaturized, low mass platform and payload then allows the Gossamer-3 solar sail to potentially double the warning time of space weather events. The mission profile and mass budgets will be presented to achieve these ambitious goals. Y1 - 2014 SN - 978-3-642-34906-5 (Print) ; 978-3-642-34907-2 (E-Book) SP - 227 EP - 242 PB - Springer CY - Berlin [u.a.] ER - TY - GEN A1 - Duwe, A. A1 - Schlegel, C. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Sequentielle Extraktion von Cellulose zur effizienten Nutzung der Stoffströme in der Holzbioraffinerie T2 - Chemie Ingenieur Technik N2 - In der Reihe der nachwachsenden Rohstoffe besitzt Holz als erneuerbare und umweltfreundliche Ressource ein großes Potenzial. Über 11 Mio. ha Holz, das laut der Fachagentur für nachwachsende Rohstoffe (FNR) auch für industrielle Zwecke genutzt werden kann, wuchsen im Jahr 2013 allein auf bundesdeutscher Fläche. 56,8 Mio. m³ jährlicher Holzeinschlag in den letzten zehn Jahren wurde zu knapp der Hälfte stofflich und der Rest energetisch verwertet. Im Rahmen dieser Arbeit konnte auf der Basis vom Holz der Buche, die nach Fichte und Kiefer die dritthäufigste Baumart in Deutschland ist und 15% der deutschen Waldfläche ausmacht, die Fraktionierung der polymeren Hauptbestandteile mit niedrigem energetischen Einsatz erreicht werden. Hierbei werden in einem nachgeschalteten Extraktionsprozess die beiden Komponenten Hemicellulose und Lignin in flüssiger Form von der finalen festen Cellulosefraktion abgetrennt. Die Extraktion der Hemicellulose erfolgt durch eine Liquid Hot Water (LHW)-Behandlung. Untersucht wird der katalytische Zusatz anorganischer Säuren wie H₃PO₄ und H₂SO₄. Im Hinblick auf die weitere Verwertung von Lignin zu aromatischen Synthesebausteinen kommt die Organosolv-Extraktion mit einem Ethanol/Wasser-Gemisch zum Einsatz. Von Vorteil ist die weitere Verwendung beider Stoffströme ohne Fällungsschritt und nachteiliger Verdünnung der Hemicellulose. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450308 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1400 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Huck, Christina A1 - Poghossian, Arshak A1 - Bäcker, Matthias A1 - Reisert, Steffen A1 - Schubert, J. A1 - Zander, W. A1 - Begoyan, V. K. A1 - Buniatyan, V. V. A1 - Schöning, Michael Josef T1 - Chemical sensors based on a high-k perovskite oxide of barium strontium titanate JF - Procedia Engineering N2 - High-k perovskite oxide of barium strontium titanate (BST) represents a very attractive multi-functional transducer material for the development of (bio-)chemical sensors for liquids. In this work, BST films have been applied as a sensitive transducer material for a label-free detection of adsorbed charged macromolecules (positively charged polyelectrolytes) and concentration of hydrogen peroxide vapor as well as protection insulator layer for a contactless electrolyte-conductivity sensor. The experimental results of characterization of individual sensors are presented. Special emphasis is devoted towards the development of a capacitively-coupled contactless electrolyte-conductivity sensor. KW - barium strontium titanate KW - high-k material KW - contactless conductivity sensor KW - multi-functional material KW - hydrogen peroxide Y1 - 2014 U6 - https://doi.org/10.1016/j.proeng.2014.11.258 SN - 1877-7058 N1 - EUROSENSORS 2014 ; European Conference on Solid-State Transducers <28, 2014> VL - 87 SP - 28 EP - 31 PB - Elsevier CY - Amsterdam ER - TY - RPRT A1 - Pisarczyk, Rafael A1 - Ritz, Thomas A1 - Wallenborn, Ramona T1 - Unterschiedliche Entwicklungsansätze von Multiplattform-Anwendungen : Marktübersicht N2 - Die Marktübersicht „Unterschiedliche Entwicklungsansätze von Multiplattform-Anwendungen“ richtet sich an IT-Dienstleister, Entwickler und IT-Abteilungen von Unternehmen, die Multiplattform Anwendungen entwickeln. In dieser Marktübersicht werden verschiedene Entwicklungsansätze beschrieben und ihre jeweiligen Vor- und Nachteile aufgezeigt. Y1 - 2014 N1 - Mittelstand Digital PB - eBusiness-Lotse CY - Aachen ER - TY - JOUR A1 - Tippkötter, Nils A1 - Duwe, Anna-Maria A1 - Wiesen, Sebastian A1 - Sieker, Tim A1 - Ulber, Roland T1 - Enzymatic hydrolysis of beech wood lignocellulose at high solid contents and its utilization as substrate for the production of biobutanol and dicarboxylic acids JF - Bioresource Technology N2 - The development of a cost-effective hydrolysis for crude cellulose is an essential part of biorefinery developments. To establish such high solid hydrolysis, a new solid state reactor with static mixing is used. However, concentrations >10% (w/w) cause a rate and yield reduction of enzymatic hydrolysis. By optimizing the synergetic activity of cellulolytic enzymes at solid concentrations of 9%, 17% and 23% (w/w) of crude Organosolv cellulose, glucose concentrations of 57, 113 and 152 g L⁻¹ are reached. However, the glucose yield decreases from 0.81 to 0.72gg⁻¹ at 17% (w/w). Optimal conditions for hydrolysis scale-up under minimal enzyme addition are identified. As result, at 23% (w/w) crude cellulose the glucose yield increases from 0.29 to 0.49gg⁻¹. As proof of its applicability, biobutanol, succinic and itaconic acid are produced with the crude hydrolysate. The potential of the substrate is proven e.g. by a high butanol yield of 0.33gg⁻¹. Y1 - 2014 U6 - https://doi.org/10.1016/j.biortech.2014.06.052 VL - 167 SP - 447 EP - 455 PB - Elsevier CY - Amsterdam ER - TY - GEN A1 - Hering, T. A1 - Pasteur, A. A1 - Wollny, S. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Magnetische Separation von Gold-Nanopartikeln zur Gluconsäure-Produktion durch Hochgradient-Magnetseparation im Labormaßstab T2 - Chemie Ingenieur Technik N2 - Bei der Verarbeitung nachwachsender Rohstoffe entsteht aus Cellulose oder Stärke u. a. das wichtige Produkt Glucose. Diese niedermolekulare Kohlenhydratquelle wird üblicherweise als Substrat für biotechnologische und chemische Synthesen verwendet. Ein wirtschaftlich interessantes Oxidationsprodukt der Glucose ist Gluconsäure, die beispielsweise als Lebensmittelzusatzstoff (E 574), in der Medizin und Metallindustrie Verwendung findet. Die Umsetzung des Monosaccharids zu Gluconsäure erfolgt entweder durch mikrobielle Fermentation oder der Oxidation an heterogenen Katalysatoren. Die Zielsetzung der Studie ist die Untersuchung der Glucoseoxidation an magnetisierbaren Gold-Nanopartikeln unter nachfolgender Bypass-Separation des Katalysators mittels einer neuen Mini-HGMS-Einheit (Hochgradient-Magnetseparation). Dieser Filtertyp ermöglicht die selektive Trennung magnetischer Partikel aus Suspensionen mit hohem Feststoffgehalt oder Viskosität. Erste Ergebnisse zeigen eine Beladungskapazität des selbstkonstruierten Mini-HGMS von 550 mg goldbeschichteter magnetisierbarer Nanopartikel. Die Oxidation erfolgt bei einem pH-Wertvon 9, bei 40 °C und mit 100 mM Glucose in einem begasten Rührkesselreaktor. Das System soll zukünftig zum Katalysatorrecycling von hochviskosen und Feststoffbelasteten Produktströmen aus Bioraffinerien eingesetzt werden. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450265 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1501 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Tippkötter, Nils A1 - Wollny, Steffen A1 - Suck, Kirstin A1 - Sohling, Ulrich A1 - Ruf, Friedrich A1 - Ulber, Roland T1 - Recycling of spent oil bleaching earth as source of glycerol for the anaerobic production of acetone, butanol, and ethanol with Clostridium diolis and lipolytic Clostridium lundense JF - Engineering in Life Sciences N2 - A major part of edible oil is subjected to bleaching procedures, primarily with minerals applied as adsorbers. Their recycling is currently done either by regaining the oil via organic solvent extraction or by using the spent bleaching earth (SBE) as additive for animal feed, etc. As a new method, the reutilization of the by-product SBE for the microbiologic formation of acetone, butanol, and ethanol (ABE) is presented as proof-of-concept. The SBE was taken from a palm oil cleaning process. The recycling concept is based on the application of lipolytic clostridia strains. Due to considerably long fermentation times, co-fermentation with Candida rugosa and enzymatic hydrolyses of the bound oil with a subsequent clostridia fermentation are shown as alternative routes. Anaerobic fermentations under comparison of different clostridia strains were performed with glycerol media, enzymatically hydrolyzed palm oil and SBE. Solutes, side product compositions and productivities were quantified via HPLC. A successful production of ABE solutes from SBE has been done with a yield of 0.15 g butanol per gram of bound glycerol. Thus, the biotechnological recycling of the waste stream is possible in principle. Inhibition of the substrate suspension has been observed. A chromatographic ion-exchange of substrates increased the biomass concentration. Y1 - 2014 U6 - https://doi.org/10.1002/elsc.201300113 SN - 1618-2863 VL - 14 IS - 4 SP - 425 EP - 432 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Hering, T. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Aktiver und passiver antimikrobieller Oberflächenschutz durch funktionalisierte Mikropartikel T2 - Chemie Ingenieur Technik N2 - Mikrobielle Verunreinigungen von Oberflächen in technischen und medizinischen Systemen sind allgegenwärtig. Sie basieren üblicherweise auf adsorptiven Oberflächenbindungen organischer Komponenten (Proteine und Fette) oder Membrankomponenten aerogener sowie wassergebundener Mikroorganismen. In laufenden Forschungsarbeiten wird eine aktive sowie passive Biomodifikation von Oberflächen zu deren Schutz vor Adsorption von Proteinen und Mikroorganismen verfolgt. Der antimikrobielle Schutz soll dabei sowohl durch die Mikrostrukturierung bzw. Rauheitsanpassung der Oberflächen durch deren Beschichtung mit Mikro-und Nanopartikeln erfolgen. Ferner werden antimikrobielle Enzyme und funktionelle Gruppen auf den Mikropartikeln gebunden, um den Oberflächenschutz zu verstärken. In ersten Versuchen wurden quartäre Ammoniumverbindungen auf eigens synthetisierten superparamagnetischen Eisenoxid-Nanopartikeln (Durchmesser 10 – 30 nm) immobilisiert und die wachstumshemmende Wirkung untersucht. Erste Ergebnisse zeigten, dass eine Konzentration von 10 mg mL⁻¹ der Ammoniumverbindung in einer Wachstumshemmung des verwendeten Gram-negativen Modell-Mikroorganismus E. coli GFPmut2 resultiert. Zurzeit werden synergistisch wirkende Kombinationen von Partikeln mit Proteasen, quartären Ammoniumverbindungen, hydrophoben Oberflächen und mikrostrukturierten Oberflächen als antimikrobieller Schutz untersucht. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450264 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 9 IS - 86 SP - 1474 EP - 1475 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Huck, Christina A1 - Poghossian, Arshak A1 - Kerroumi, Iman A1 - Schusser, Sebastian A1 - Bäcker, Matthias A1 - Zander, Willi A1 - Schubert, Jürgen A1 - Buniatyan, Vahe V. A1 - Martirosyan, Norayr W. A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Multiparameter sensor chip with Barium Strontium Titanate as multipurpose material JF - Electroanalysis N2 - It is well known that biochemical and biotechnological processes are strongly dependent and affected by a variety of physico-chemical parameters such as pH value, temperature, pressure and electrolyte conductivity. Therefore, these quantities have to be monitored or controlled in order to guarantee a stable process operation, optimization and high yield. In this work, a sensor chip for the multiparameter detection of three physico-chemical parameters such as electrolyte conductivity, pH and temperature is realized using barium strontium titanate (BST) as multipurpose material. The chip integrates a capacitively coupled four-electrode electrolyte-conductivity sensor, a capacitive field-effect pH sensor and a thin-film Pt-temperature sensor. Due to the multifunctional properties of BST, it is utilized as final outermost coating layer of the processed sensor chip and serves as passivation and protection layer as well as pH-sensitive transducer material at the same time. The results of testing of the individual sensors of the developed multiparameter sensor chip are presented. In addition, a quasi-simultaneous multiparameter characterization of the sensor chip in buffer solutions with different pH value and electrolyte conductivity is performed. To study the sensor behavior and the suitability of BST as multifunctional material under harsh environmental conditions, the sensor chip was exemplarily tested in a biogas digestate. Y1 - 2014 U6 - https://doi.org/10.1002/elan.201400076 SN - 1521-4109 (E-Journal); 1040-0397 (Print) VL - 26 IS - 5 SP - 980 EP - 987 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Butenweg, Christoph A1 - Meyer, Udo A1 - Fehling, Ekkehard T1 - INSYSME: first activities of the German partners T2 - 9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014 Y1 - 2014 ER - TY - JOUR A1 - Akimbekov, Nuraly S. A1 - Digel, Ilya A1 - Zhubanova, A. A. T1 - Advantages of creation of e-books in training of specialists biologists and biotechnologists JF - KazNU Bulletin. Biology series. N2 - The necessity of e-books as a primary of learning, its opportunities for realization of competence during training biologist and biotechnologist specialists are determined. Definitions and requirements to the e-books, its advantages in comparison with traditional textbooks, and the ways of creation of e-books in the SunRav BookEditor program are considered. KW - SunRav BookEditor KW - softs KW - distance learning KW - e-issues KW - e-books Y1 - 2014 SN - 1563-0218 VL - 60 IS - 1 SP - 249 EP - 252 PB - Al-Farabi Kazakh National University CY - Almaty ER - TY - PAT A1 - Al-Kaidy, Huschyar A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Vorrichtung und Verfahren zur Bestimmung des Kontaktwinkels eines flüssigen oder mit Flüssigkeit gefüllten Körpers [Offenlegungsschrift] N2 - Die vorliegende Erfindung betrifft eine Vorrichtung und ein Verfahren zur Bestimmung des Kontaktwinkels eines flüssigen oder mit Flüssigkeit gefüllten Körpers. Dieser besteht aus einem Träger (1) und einer damit verbundenen, in einem Winkelbereich von mehr als 0° bis maximal 90° neigbaren Ebene (8) mit einer darin ausgebildeten Abrollbahn (9) für den flüssigen oder mit Flüssigkeit gefüllten Körper. An der Ebene (8) sind mehrere Sensoren (11, 12) zur Erfassung der Rolldauer des Körpers entlang der Rollstrecke angeordnet. Erfindungsgemäß ist vorgesehen, dass die Einstellung des Neigungswinkels der Ebene (8) über ein Winkelmessgerät (10) erfolgt, wodurch ein Abrollwinkel erfassbar ist, bei dem der Körper in Bewegung gerät. Aus der Rolldauer, der Rollstrecke und dem Abrollwinkel wird der Kontaktwinkel des Körpers ermittelt. Y1 - 2014 PB - Deutsches Patent- und Markenamt CY - München ER - TY - JOUR A1 - Wu, Chunsheng A1 - Bronder, Thomas A1 - Poghossian, Arshak A1 - Werner, Frederik A1 - Bäcker, Matthias A1 - Schöning, Michael Josef T1 - Label-free electrical detection of DNA with a multi-spot LAPS: First step towards light-addressable DNA chips JF - Physica status solidi A : Applications and materials science N2 - A multi-spot (4 × 4 spots) light-addressable potentiometric sensor (MLAPS) consisting of an Al–p-Si–SiO2 structure has been applied for the label-free electrical detection of DNA (deoxyribonucleic acid) immobilization and hybridization by the intrinsic molecular charge for the first time. Single-stranded probe ssDNA molecules (20 bases) were covalently immobilized onto the silanized SiO2 gate surface. The unspecific adsorption of mismatch ssDNA on the MLAPS gate surface was blocked by bovine serum albumin molecules. To reduce the screening effect and to achieve a high sensor signal, the measurements were performed in a low ionic-strength solution. The photocurrent–voltage (I–V) curves were simultaneously recorded on all 16 spots after each surface functionalization step. Large shifts of I–V curves of 25 mV were registered after the DNA immobilization and hybridization event. In contrast, a small potential shift (∼5 mV) was observed in case of mismatch ssDNA, revealing good specificity of the sensor. The obtained results demonstrate the potential of the MLAPS as promising transducer platform for the multi-spot label-free electrical detection of DNA molecules by their intrinsic molecular charge. Y1 - 2014 U6 - https://doi.org/10.1002/pssa.201330442 SN - 1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print) VL - 211 IS - 6 SP - 1423 EP - 1428 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Wu, Chunsheng A1 - Bronder, Thomas A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - DNA-hybridization detection using light-addressable potentiometric sensor modified with gold layer T2 - Sensoren und Messsysteme 2014 ; Beiträge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in Nürnberg. (ITG-Fachbericht ; 250) Y1 - 2014 SN - 978-3-8007-3622-5 SP - 1 EP - 4 PB - VDE-Verl. CY - Düsseldorf ER - TY - CHAP A1 - Huck, Christina A1 - Poghossian, Arshak A1 - Buniatyan, V. A1 - Schöning, Michael Josef T1 - Multi-parameter detection for supporting monitoring and control of biogas processes in agriculture T2 - Sensoren und Messsysteme 2014 ; Beiträge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in Nürnberg. (ITG-Fachbericht ; 250) Y1 - 2014 SN - 978-3-8007-3622-5 SP - 1 EP - 5 PB - VDE-Verl. CY - Berlin ER - TY - CHAP A1 - Anthrakidis, Anette A1 - Herrmann, Ulf A1 - Mirza, M. F. A1 - Schorn, Christian A1 - Schwarzer, Klemens A1 - Wedding, Philipp A1 - Weis, Fabian T1 - Parabolrinnenentwicklung und Qualifizierung am Solar-Institut Jülich T2 - Thermische Solarenergie : 24. Symposium ; 7. bis 9. Mai 2014, Kloster Banz, Bad Staffelstein Y1 - 2014 SN - 978-3-943891-35-5 SP - 242 EP - 243 PB - OTTI CY - Regensburg ER - TY - CHAP A1 - Schöning, Michael Josef A1 - Poghossian, Arshak A1 - Glück, Olaf A1 - Thust, Marion T1 - Electrochemical methods for the determination of chemical variables in aqueous media T2 - Measurement, instrumentation, and sensors handbook / ed. by John G. Webster [u.a.] Vol. 2 : Electromagnetic, optical, radiation, chemical, and biomedical measurement Y1 - 2014 SN - 978-1-4398-4891-3 SP - 55-1 EP - 55-54 PB - CRC Pr. CY - Boca Raton, Fla. ER - TY - JOUR A1 - Holtrup, S. A1 - Sadeghfam, Arash A1 - Heuermann, Holger A1 - Awakowicz, P. T1 - Characterization and optimization technique for microwave-driven high-intensity discharge lamps using hot S-parameters JF - IEEE transactions on microwave theories and techniques N2 - High-intensity discharge lamps can be driven by radio-frequency signals in the ISM frequency band at 2.45 GHz, using a matching network to transform the impedance of the plasma to the source impedance. To achieve an optimal operating condition, a good characterization of the lamp in terms of radio frequency equivalent circuits under operating conditions is necessary, enabling the design of an efficient matching network. This paper presents the characterization technique for such lamps and presents the design of the required matching network. For the characterization, a high-intensity discharge lamp was driven by a monofrequent large signal at 2.45 GHz, whereas a frequency sweep over 300 MHz was performed across this signal to measure so-called small-signal hot S-parameters using a vector network analyzer. These parameters are then used as an equivalent load in a circuit simulator to design an appropriate matching network. Using the measured data as a black-box model in the simulation results in a quick and efficient method to simulate and design efficient matching networks in spite of the complex plasma behavior. Furthermore, photometric analysis of high-intensity discharge lamps are carried out, comparing microwave operation to conventional operation. Y1 - 2014 U6 - https://doi.org/10.1109/TMTT.2014.2342652 SN - 0018-9480 VL - 62 IS - 10 SP - 2471 EP - 2480 PB - IEEE CY - New York ER - TY - CHAP A1 - Laack, Walter van T1 - Zu neuen wissenschaftlichen Erkenntnissen zur Vereinbarkeit von Vernunft und Glaube T2 - Ethik und Moral in Staat, Wirtschaft und Gesellschaft : 5. Rotary-Tag, 14.-15.2.2014, Kleve Y1 - 2014 SN - 978-3-944011-21-9 SP - 152 EP - 162 PB - Edition Virgines CY - Lingen ER - TY - JOUR A1 - Laack, Walter van T1 - Therefore Fermat is right JF - American journal of humanities and social sciences : AJHSS N2 - It was Fernat's idea to investigate how many numbers would fulfill the equation according to the Pythagorean Theorem if the exponent were increased to random, e.g. to a3 + b3 = c3. His question became therefore: are there two whole numbers the cubes of which add up to the volume of the cube of a third whole number? He posed this same question, of course, for all kinds of higher exponents, so that the equation could be generalized: is there an integral solution for the equation an + bn = cn, if the exponent n is higher than 2? Although in 1993, the English mathematician Andrew Wiles was able to produce an arithmetical proof for Fermat's famous theorem, I will show that there is a simple logical explanation which is also pragmatic and plausible and what is the result of a fundamental alternative idea how our world seems to be constructed. Y1 - 2014 SN - 2329-079X (E-Journal); 2329-0781 (Print) VL - 2 IS - 2 SP - 117 EP - 120 ER - TY - CHAP A1 - Schöning, Michael Josef A1 - Poghossian, Arshak A1 - Glück, Olaf A1 - Thust, Marion T1 - Electrochemical composition measurement T2 - Measurement, instrumentation, and sensors handbook: electromagnetic, optical, radiation, chemical, and biomedical measuremen Y1 - 2014 SN - 978-1-4398-4891-3 SP - 55-1 EP - 55-54 PB - CRC Pr. CY - Boca Raton, Fa. ET - 2nd ed. ER - TY - JOUR A1 - Laack, Walter van T1 - Nature is much smarter than expected: the Genetic Code is not degenerate JF - American journal of humanities and social sciences N2 - In any books about genetics it can still today be read that our genetic code is called “degenerate” because it is still believed that 43 = 64 triplets encode the 20 essential amino acids. Indeed we have to assume the inverse law, what means that 34 = 81 exact code positions are really effective for our genetic code and encode the amino acids, compiled to proteins. This very important discovery leads to two completely new results that are limits-overlooking: 1) 34 (=81) genetic code positions mean exactly the same number as there are stable and naturally existing chemical elements in our universe. This famous argument should now lead to some alternative, as well as new fundamental conclusions about our existence. 2) A genetic code positioning system shows that nature is much smarter than expected: mutations are made less dangerous than believed, because they won't be that easily able any more to cause severe damages in the protein-synthesis. This should also lead to some alternative views upon evolution of life. Y1 - 2014 SN - 2329-0781 (Print) ; 2329-079X (Online) VL - Vol. 2 IS - No. 1 SP - 10 EP - 12 ER - TY - GEN A1 - Ritz, Thomas T1 - Multiplattformentwicklung für mobile Informationssysteme : eine strategische Perspektive ; [Vortragsfolien] T2 - Info-Veranstaltung Multiplattform-Entwicklung für mobile Entwicklungen, Dezember 2013 Y1 - 2014 ER - TY - JOUR A1 - Beck, Daniel A1 - Buchleitner, Martin A1 - Ferrein, Alexander A1 - Niemüller, Tim A1 - Steinbauer, Gerald T1 - Mostly Harmless & AllemaniACs - mixed innovations Y1 - 2014 SP - 1 EP - 8 ER - TY - RPRT A1 - Ritz, Thomas A1 - Siekmann, Kirsten A1 - Wallenborn, Ramona T1 - 3D-Druck – Prozessmanagement für individualisierte Massenprodukte : Wie können Fertigungsdienstleister in die endkundengerichtete Produktion integriert werden? ; Info-Broschüre N2 - Die Informationsbroschüre „3D-Druck – Prozessmanagement für individualisierte Massenprodukte“ richtet sich an 3D-Druckdienstleister, die additive Fertigungsverfahren (Additive Manufacturing) nutzen, sowie an IT-Dienstleister, die eine Plattform für den Datenaustausch und die Individualisierung anbieten. Mit der additiven 3D-Drucktechnologie erfolgt die Fertigung von Produkten durch einen schichtweisen Aufbau. In dieser Broschüre werden mögliche Potenziale im Bereich der Herstellung mittels additiver Fertigungsverfahren aufgezeigt. Y1 - 2014 PB - eBusiness-Lotse CY - Aachen ER - TY - GEN A1 - Tippkötter, Nils A1 - Duwe, Anna A1 - Rais, Dominik A1 - Zibek, Susanne A1 - Zorn, H. T1 - Optimierung und Scale-up der enzymatischen Hydrolyse inkl. Ligninabbau T2 - Chemie Ingenieur Technik N2 - Primäre Ziele der Hydrolyse pflanzlicher nachwachsender Rohstoffe sind möglichst hohe Zuckerkonzentrationen für nachfolgende Fermentationen und eine Maximierung der Produktivität. Zur Optimierung dieser Prozesse wird Organosolv-aufgeschlossene Buchenholz-Cellulose verwendet. Die Hydrolyse des Faserstoffes erfolgt mithilfe von Novozymes CTec2-Enzymen. Die Hydrolysen konnten durch neue Rührerelemente auf einen Maßstab von 1000 L übertragen werden. Dabei konnten maximale Ausbeuten (g Glucose g –1 Glucose im Faserstoff) bis 81 g g – 1 und Konzentrationen von 152 g L –1 erreicht werden. Zurzeit können unter Einsatz eines Feststoffreaktors Cellulosefasern in einer Konzentration bis 400 g L –1 enzymatisch hydrolysiert werden. Die cellulolytischen Enzyme stoßen bei hohen Feststoffkonzentrationen an ihre Grenzen. Mit steigendem Feststoffgehalt nimmt die Hydrolyseausbeute ab. Ein Ansatz zur Steigerung der Effizienz ist der Einsatz ligninolytischer Enzyme, die Ligninreste an der Organosolv-Cellulose aufschließen können. Eine solche Verbesserung der Zugänglichkeit für cellulolytische Enzyme an ihr Substrat wurde durch Kulturüberstände verschiedener ligninolytischer Pilze erreicht. Mit Kulturüberständen von Stereum sp. sind Steigerungen der Glucoseausbeuten um bis zu 30 % möglich. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450287 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen N1 - Förderung vom Bundesministeriumfür Ernährung und Landwirtschaftdurch den Projektträger FNR e. V. im Rahmen des Projekts FKZ 22019409 VL - 86 IS - 9 SP - 1515 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Buniatyan, V. V. A1 - Huck, Christina A1 - Poghossian, Arshak A1 - Schöning, Michael Josef A1 - Rustamyan, L. G. A1 - Hovnikyan, H. H. T1 - Equivalent circuit and optimization of impedance characteristics of an electrolyte conductivity sensor T2 - Proceedings of State Engineering University Armenia : Series Information technologies, electronics, radio engineering Y1 - 2014 VL - Iss. 17 IS - No. 1 SP - 69 EP - 76 ER - TY - CHAP A1 - Niedermeier, H. A1 - Clemens, J. A1 - Kowalski, Julia A1 - Macht, S. A1 - Heinen, D. A1 - Hoffmann, R. A1 - Linder, Peter T1 - Navigation system for a research ice probe for antarctic glaciers T2 - IEEE/ION Position, Location and Navigation Symposium (PLANS) ; 5-8 May 2014, Monterey, Calif. Y1 - 2014 SN - 978-1-4799-3319-8 SP - 959 EP - 975 PB - IEEE CY - Piscataway, NJ ER - TY - JOUR A1 - Wolf, Martin R. A1 - Biesen, Ina van der A1 - Greeb, Birgit T1 - Mein Freund, die Uni JF - Die neue Hochschule : DNH : für anwendungsbezogene Wissenschaft und Kunst Y1 - 2014 SN - 0340-448X N1 - Gedr. Ausgabe in der Bibliothek Eupener Str. vorhanden. VL - 2014 IS - 2 SP - 54 EP - 56 PB - HLB CY - Bonn ER - TY - GEN A1 - Tippkötter, Nils A1 - Wiesen, S. A1 - Thiel, A. A1 - Muffler, K. A1 - Ulber, Roland T1 - Biotechnologische Wertstoffgewinnung entlang der Prozessketten Grüner und Pflanzenöl-Bioraffinerien T2 - Chemie Ingenieur Technik N2 - Der nachwachsende Rohstoff Raps ist in großen Mengen verfügbar und eine Quelle für Biomoleküle mit hohem Wertschöpfungspotenzial. Entwicklungen zur biotechnologischen Wertstoffgewinnung werden dabei schwerpunktmäßig in den Bereichen Aufarbeitung und Funktionalisierung von Polyphenolen und Fetten betrieben. Bei der Verarbeitung der Pflanzenmaterialien werden dabei insbesondere Verfahren zur adsorptiven Aufreinigung und Auftrennung mittels Materialien mit modifizierten Bleicherden und anderen organischen oder anorganischen Adsorbentien untersucht. Ferner wurden für die Aufreinigung von Polyphenolen adsorptive sowie extraktive Prozesse entwickelt. Bei den Entwicklungen wird berücksichtigt, dass Bioraffinerien auf eine fortwährende Gewährleistung eines hohen Produktions- bzw. Lieferbedarfs nachwachsender Rohstoffe angewiesen sind. Somit werden Optionen dezentraler regionaler Vorbehandlungs- und Wertschöpfungsketten in der Nähe landwirtschaftlicher Betriebe einbezogen. Neben neuen Aufreinigungsverfahren werden mikrobielle und enzymatische Prozesse zur wertsteigernden Umsetzung von Glycerin, Polyphenolen und Zuckermonomeren vorgestellt sowie Limitierungen nachwachsender Rohstoffe der 2. Generation diskutiert. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450283 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen N1 - Diese Arbeiten werden vom Bundesministerium für Ernährung und Landwirtschaft durch den Projektträger FNR e. V. im Rahmen des Projekts FKZ22022908 gefördert VL - 86 IS - 9 SP - 1605 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Oertel, Mario A1 - Bung, Daniel Bernhard T1 - Numerische Strömungssimulation von Fließgewässern - Wo stehen wir und was werden wir im Laufe der nächsten Jahre erreichen? T2 - Simulationsverfahren und Modelle für Wasserbau und Wasserwirtschaft = Simulation techniques and models for hydraulic engineering and water management / 37. Dresdner Wasserbaukolloquium 2014, 13. - 14. März 2014. (Dresdner wasserbauliche Mitteilungen ; H. 50) Y1 - 2014 SN - 978-3-86780-349-6 SP - 19 EP - 30 ER - TY - JOUR A1 - Bronder, Thomas A1 - Wu, Chunsheng A1 - Poghossian, Arshak A1 - Werner, Frederik A1 - Keusgen, M. A1 - Schöning, Michael Josef T1 - Label-free detection of DNA hybridization with light-addressable potentiometric sensors: comparison of various DNA-immobilization strategies JF - Procedia Engineering N2 - Light-addressable potentiometric sensors (LAPS) consisting of a p-Si-SiO2 and p-Si-SiO2-Au structure, respectively, have been tested for a label-free electrical detection of DNA (deoxyribonucleic acid) hybridization. Three different strategies for immobilizing single-stranded probe DNA (ssDNA) molecules on a LAPS surface have been studied and compared: (a) immobilization of thiol-modified ssDNA on the patterned Au surface via gold-thiol bond, (b) covalent immobilization of amino-modified ssDNA onto the SiO2 surface functionalized with 3-aminopropyltriethoxysilane and (c) layer-by-layer adsorption of negatively charged ssDNA on a positively charged weak polyelectrolyte layer of poly(allylamine hydrochloride). KW - LAPS KW - lable-free detection KW - DNA hybridization KW - field-effect sensor Y1 - 2014 U6 - https://doi.org/10.1016/j.proeng.2014.11.647 SN - 1877-7058 N1 - EUROSENSORS 2014 ; European Conference on Solid-State Transducers <28, 2014> VL - 87 SP - 755 EP - 758 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Bäcker, Matthias A1 - Schusser, Sebastian A1 - Leinhos, Marcel A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - Sensor system for the monitoring of degradation processes of biodegradable biopolymers T2 - Sensoren und Messsysteme 2014 ; Beiträge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in Nürnberg. (ITG-Fachbericht ; 250) Y1 - 2014 SN - 978-3-8007-3622-5 SP - 1 EP - 4 PB - VDE-Verl. CY - Düsseldorf ER - TY - JOUR A1 - Laack, Walter van T1 - Nahtoderfahrungen aus medizinischer Sicht JF - Deutsche medizinische Wochenschrift : DMW N2 - Nah- versus Nachtoderfahrungen Nahtoderfahrungen (NTE) sind ein Phänomen aus der Kategorie „außergewöhnliche Bewusstseinserfahrungen“. Sie treten in unmittelbarer Nähe des eigenen Todes auf. Oft, aber nicht immer, handelt es sich dabei um Erfahrungen von Personen, die durch ärztliche Maßnahmen wiederbelebt wurden und später davon berichten (NTE-ler). Jedoch kommen solche Phänomene auch bei Menschen vor, die während einer schweren Erkrankung eine lebensbedrohliche Krise haben, hiervon aber spontan genesen. Den NTE ähnlich sind auch sogenannte Nachtod-erfahrungen sowie spontane Erlebnisse, die im Rahmen anderer außergewöhnlicher Stresssituationen auftreten. Von Nachtoderfahrungen spricht man, wenn die Betroffenen anlässlich des Todes von geliebten Angehörigen oder Freunden Erlebnisse haben, die inhaltlich ebenfalls, zumindest aber teilweise, denen von NTE entsprechen. Nachtoderfahrungen sowie spontane NTE-ähnliche Erlebnisse unterscheiden sich jedoch von den echten NTE zumeist sowohl quantitativ als auch qualitativ. Unter einem quantitativen Unterschied versteht man in diesem Zusammenhang eine in der Regel geringer ausgeprägte Komplexität, als sie sehr vielen NTE zu eigen ist. Da sich aber auch viele NTE selbst bezüglich ihrer Komplexität unterscheiden, ist der Hauptunterschied qualitativer Natur: Echte NTE besitzen gegenüber den anderen hier erwähnten Phänomenen eine größere inhaltliche und emotionale Tiefe. Sie begleiten die Betroffenen anschließend ein Leben lang – zumeist mit positiven, in Einzelfällen aber auch mit negativen Folgen, die bis zu einem späteren Suizid reichen können. Die genannten außergewöhnlichen Bewusstseinsphänomene lassen sich in ihrer Gesamtheit bei rund 5 % der Bevölkerung finden. NTE im Speziellen haben hiervon einen durchaus bedeutenden Anteil. Je nach Studie geben zwischen 18 % und 40 % aller Personen, die reanimiert wurden, an, währenddessen eine NTE erlebt zu haben. Dass nicht alle eine solche Erfahrung machen, wird von Kritikern gern dahingehend interpretiert, NTE seien rein physiologischer und keineswegs spiritueller Natur. Jedoch sollte man bedenken, dass im Fall einer rein neurophysiologischen Grundlage von NTE dann bei jedem ein solches Phänomen zu erwarten wäre, so wie beispielsweise auch die Symptome einer Hypoglykämie im Wesentlichen immer dieselben sind. Y1 - 2014 U6 - https://doi.org/10.1055/s-0034-1387363 SN - 1439-4413 (E-Journal); 0012-0472 (Print); 1437-5982 (Print) VL - Jg. 139 IS - H. 51/52 SP - 2651 EP - 2654 PB - Thieme CY - Stuttgart ER - TY - JOUR A1 - Rau, Christoph A1 - Alexopoulos, Spiros A1 - Breitbach, Gerd A1 - Hoffschmidt, Bernhard A1 - Latzke, Markus A1 - Sattler, Johannes Christoph T1 - Transient simulation of a solar-hybrid tower power plant with open volumetric receiver at the location Barstow JF - Energy procedia : proceedings of the SolarPACES 2013 International Conference N2 - In this work the transient simulations of four hybrid solar tower power plant concepts with open-volumetric receiver technology for a location in Barstow-Daggett, USA, are presented. The open-volumetric receiver uses ambient air as heat transfer fluid and the hybridization is realized with a gas turbine. The Rankine cycle is heated by solar-heated air and/or by the gas turbine's flue gases. The plant can be operated in solar-only, hybrid parallel or combined cycle-only mode as well as in any intermediate load levels where the solar portion can vary between 0 to 100%. The simulated plant is based on the configuration of a solar-hybrid power tower project, which is in planning for a site in Northern Algeria. The meteorological data for Barstow-Daggett was taken from the software meteonorm. The solar power tower simulation tool has been developed in the simulation environment MATLAB/Simulink and is validated. Y1 - 2014 U6 - https://doi.org/10.1016/j.egypro.2014.03.157 SN - 1876-6102 VL - 49 SP - 1481 EP - 1490 PB - Elsevier CY - Amsterdam ER - TY - VIDEO A1 - Ritz, Thomas T1 - Multiplattformentwicklung für mobile Informationssysteme : eine strategische Perspektive T2 - Info-Veranstaltung Multiplattform-Entwicklung für mobile Anwendungen, Dezember 2013 Y1 - 2014 ER - TY - CHAP A1 - Gebhardt, Andreas A1 - Ritz, Thomas A1 - Siekmann, Kirsten A1 - Wallenborn, Ramona ED - Demmer, Axel T1 - Additive manufacturing businesses in the process chain of individualized mass products T2 - DDMC 2014 : Proceedings of the Fraunhofer Direct Digital Manufacturing Conference Y1 - 2014 SN - 978-3-8396-9128-1 (E-Book) PB - Fraunhofer CY - Stuttgart ER - TY - GEN A1 - Duwe, A. A1 - Sieker, T. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Grasssilage als Substrat zur fermentativen Produktion organischer Säuren T2 - Chemie Ingenieur Technik N2 - Der zunehmende Bedarf an fossilen Rohstoffen bei gleichzeitig abnehmender Versorgungssicherheit führt zu einer intensiven Suche nach erneuerbaren Ressourcen. Ein vielversprechendes Ausgangsmaterial mit einer weltweiten Verfügbarkeit stellt Gras dar. In 2012 wurden in Deutschland 33 Millionen Tonnen (Heugewicht) Gras auf 4,82 Millionen Hektar Ackerland produziert, davon wurden 60,5 % siliert. Durch die Silierung kann Gras als Substrat zeitlich uneingeschränkt verfügbar sein, ohne dem Risiko des schnellen Verderbs ausgesetzt zu sein. Eine Schlüsselrolle im Rahmen des Silierprozesses nimmt die Produktion von Milchsäure ein. Milchsäure ist einbedeutendes biotechnologisches Produkt für die Lebensmittel- und die chemische Industrie. Im Rahmen dieser Arbeit wird die vollständige Umwandlung der fermentierbaren Zucker in der Silage zu Milchsäure angestrebt, um die maximale Ausbeute der organischen Säure zu erreichen. Im ersten Verfahrensschritt wird die Silage gepresst und der erhaltene Presskuchen einer Liquid-Hot-Water-Behandlung unterzogen. Durch diese einfache Vorbehandlung können hohe Glucoseausbeuten im nachfolgenden SSF-Schritt bei gleichzeitig geringem Enzymeinsatz und Chemikalienverbrauch realisiert werden. Zur Aufreinigung der Milchsäure wurden extraktive und chromatographische Methoden untersucht. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450345 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1400 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Bäcker, Matthias A1 - Schusser, Sebastian A1 - Poghossian, Arshak A1 - Schöning, Michael Josef T1 - Multi-Parametererfassung mit siliziumbasiertem Sensorchip: Aus Drei mach Eins JF - GIT Labor-Fachzeitschrift Y1 - 2014 SN - 0016-3538 IS - 2 SP - 28 EP - 30 PB - Wiley ER - TY - CHAP A1 - Poghossian, Arshak A1 - Weiland, Maryam A1 - Schöning, Michael Josef ED - Lvova, Larisa ED - Kirsanov, Dmitry ED - di Natale, Corrado ED - Legin, Audrey T1 - Nanoplate field-effect capacitors: a new transducer structure for multiparameter (bio-)chemical sensing T2 - Multisensor system for chemical analysis : materials and sensors N2 - An array of electrically isolated nanoplate field-effect silicon-on-insulator (SOI) capacitors as a new transducer structure for multiparameter (bio-)chemical sensing is presented. The proposed approach allows addressable biasing and electrical readout of multiple nanoplate field-effect capacitive (bio-)chemical sensors on the same SOI chip, as well as differential-mode measurements. The realized sensor chip has been applied for pH and penicillin concentration measurements, electrical monitoring of polyelectrolyte multilayer formation, and the label-free electrical detection of consecutive deoxyribonucleic acid (DNA) hybridization and denaturation events. Y1 - 2014 SN - 978-981-4411-15-8 ; 978-981-4411-16-5 U6 - https://doi.org/10.1201/b15491-11 SP - 333 EP - 373 PB - Jenny Stanford Publishing CY - Singapore ET - 1 ER - TY - CHAP A1 - Fuchs, Britta A1 - Ritz, Thomas T1 - Usability for Blended Shopping - Solving Major Flaws by Applying Usability Engineering and Proven Integration Technologies T2 - Proceedings of the 11th International Conference on e-Business, ICE-B 2014, Vienna, Austria Y1 - 2014 SN - 978-989-758-043-7 U6 - https://doi.org/10.5220/0005113502160223 SP - 216 EP - 223 ER - TY - JOUR A1 - Wiesen, Sebastian A1 - Tippkötter, Nils A1 - Muffler, Kai A1 - Suck, Kirstin A1 - Sohling, Ulrich A1 - Ruf, Nils A1 - Ulber, Roland T1 - Adsorptive Vorbehandlung von Rohglycerin für die 1,3-Propandiol Fermentation mit Clostridium diolis JF - Chemie Ingenieur Technik N2 - Bei der Gewinnung von Fettsäuren aus Pflanzenölen, z. B. zur Herstellung von Biopolymeren, oder bei der Biodiesel- und Seifenproduktion, fällt Glycerin als Nebenprodukt an. Bei der Biokonversion dieses Rohstoffes zu 1,3-Propandiol wird der Produktionsorganismus Clostridium diolis durch Verunreinigungen im Rohglycerin gehemmt. Als inhibierende Substanzen konnten freie Fettsäuren identifiziert werden. Mithilfe eines adsorptiven Aufarbeitungsverfahrens ist es gelungen, die Fettsäuren zu entfernen und die Konversionseffizienz zu 1,3-Propandiol zu erhöhen. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201300080 N1 - Englischer Titel: Adsorptive Pretreatment of Crude Glycerol Prior to Fermentation to 1,3-Propanediole by Clostridium Diolis VL - 86 IS - 1-2 SP - 129 EP - 135 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Al-Kaidy, Huschyar A1 - Duwe, Anna A1 - Huster, Manuel A1 - Muffler, Kai A1 - Schlegel, Christin A1 - Sieker, Tim A1 - Stadtmüller, Ralf A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Biotechnologie und Bioverfahrenstechnik – Vom ersten Ullmanns Artikel bis hin zu aktuellen Forschungsthemen JF - Chemie Ingenieur Technik N2 - Biotechnologie und die mit ihr verbundenen technischen Prozesse prägen seit Jahrtausenden die Entwicklung der Menschheit. Ausgehend von empirischen Verfahren, insbesondere zur Herstellung von Lebensmitteln und täglichen Gebrauchsgütern, haben sich diese Disziplinen zu einem der innovativsten Zukunftsfelder entwickelt. Durch das immer detailliertere Verständnis zellulärer Vorgänge können mittlerweile Produktionsstämme gezielt optimiert werden. Im Zusammenspiel mit moderner Prozesstechnik können so eine Vielzahl von Bulk- und Feinchemikalien sowie Pharmazeutika effizient hergestellt werden. In diesem Artikel werden exemplarisch einige der aktuellen Trends vorgestellt. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201400083 SN - 0009-286X VL - 86 IS - 12 SP - 2215 EP - 2225 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Pasteur, Aline A1 - Tippkötter, Nils A1 - Kampeis, Percy A1 - Ulber, Roland T1 - Optimization of high gradient magnetic separation filter units for the purification of fermentation products JF - IEEE TRANSACTIONS ON MAGNETICS N2 - High gradient magnetic separation (HGMS) has been established since the early 1970s. A more recent application of these systems is the use in bioprocesses. To integrate the HGMS in a fermentation process, it is necessary to optimize the separation matrix with regard to the magnetic separation characteristics and permeability of the non-magnetizable components of the fermentation broth. As part of the work presented here, a combined fluidic and magnetic force finite element model simulation was created using the software COMSOL Multiphysics and compared with separation experiments. Finally, as optimal lattice orientation of the separation matrix, a transversal rhombohedral arrangement was defined. The high suitability of the new filter matrix has been verified by separation experiments. Y1 - 2014 U6 - https://doi.org/10.1109/TMAG.2014.2325535 SN - 0018-9464 N1 - Article Sequence Number: 5000607 INSPEC Accession Number: 14663042 VL - 50 IS - 10 SP - Artikel 5000607 PB - IEEE CY - New York, NY ER - TY - GEN A1 - Tippkötter, Nils A1 - Roth, J. A1 - Möhring, M. A1 - Wulfhorst, H. A1 - Ulber, Roland T1 - Verwertung von Bioraffinerie-Stoffströmen am Beispiel von Einzellerproteinen T2 - Chemie Ingenieur Technik N2 - Die Nutzung von Biomasse aus pflanzlichen Abfällen für die stoffliche Verwertung rückt immer stärker in den Vordergrund. Dabei ist vor allem die ganzheitliche Verwertung der Stoffströme von Bedeutung, da diese einen integrativen Ansatz ermöglichen. Im Rahmen dieser Arbeit wird die Produktion von Einzellerproteinen (Single-Cell Proteins, SCPs) mithilfe von unterschiedlichen Rohsubstraten dargelegt. Somit können Reststoffströme, die in keiner Konkurrenz zur Produktion von Lebensmitteln stehen, für die Herstellung von Futter- und auch Nahrungsmitteln Verwendung finden. Die zunächst thermisch vorbehandelten Ausgangsmaterialien stammen aus forstwirtschaftlichen und grünen Abfällen und ermöglichen durch eine anschließende enzymatische Hydrolyse die Freisetzung von Monosacchariden. Aus diesen erfolgt die SCP-Produktion fermentativ mithilfe der drei Modellorganismen Bakterium, Hefe und Pilz. Hierfür wird sowohl das flüssige Hydrolysat als auch der feste Reststoff auf der Basis einer Feststofffermentation genutzt. Auf diese Weise ist eine vollständige Verwertung der Ausgangsmaterialien möglich. Mit den gewonnen Daten erfolgt abschließend eine Bewertung der SCPs aus nachwachsenden Rohstoffen als alternative Proteinquelle. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450257 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1399 EP - 1400 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Möhring, S. T1 - Nutzung von Fäulepilzen für die selektive Gewinnung von Cellulose und Lignin aus nicht vorbehandelter lignocellulosehaltiger Biomasse T2 - Chemie Ingenieur Technik N2 - Einige Arten der Braun- und Weißfäulepilze sind in der Lage, selektiv entweder Lignin oder Cellulose im Holz abzubauen. Diese Pilze können für eine energiesparende Vorbehandlung lignocellulosehaltiger Biomasse für Bioraffinerien genutzt werden, ohne auf technisch aufwändige Aufschlussapparate zurückgreifen zu müssen. Weißfäulepilze bauen bevorzugt Lignin ab, wodurch die verbleibende Cellulose leichter für enzymatische Hydrolysen in das Monosaccharid Glucose zugänglich wird. Braunfäulepilze bauen dagegen Cellulose und Hemicellulose ab. Die Auswirkungen der Behandlung von Weizenstroh mit verschiedenen Pilzarten werden zurzeit untersucht. Dabei werden die Veränderung der enzymatischen Hydrolysierbarkeit des Substrats sowie die gebildeten Ligninderivate bestimmt. Detaillierte Betrachtungen der Biomasseveränderung werden mithilfe spezifischer Färbemethoden durchgeführt, durch die morphologische Veränderungen der Pflanzengewebe in der 3D-Lichtmikroskopie dargestellt werden können. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450353 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen N1 - Diese Arbeit wird durch das Bundesministerium für Ernährung und Landwirtschaft über die FNR e.V. unter dem Projektnamen „Lokale Vorbehandlung nachwachsender Rohstoffe für Bioraffinerien“ gefördert (FKZ 22028411) VL - 86 IS - 9 SP - 1385 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Alhwarin, Faraj A1 - Ferrein, Alexander A1 - Scholl, Ingrid T1 - IR stereo kinect: improving depth images by combining structured light with IR stereo T2 - PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862) N2 - RGB-D sensors such as the Microsoft Kinect or the Asus Xtion are inexpensive 3D sensors. A depth image is computed by calculating the distortion of a known infrared light (IR) pattern which is projected into the scene. While these sensors are great devices they have some limitations. The distance they can measure is limited and they suffer from reflection problems on transparent, shiny, or very matte and absorbing objects. If more than one RGB-D camera is used the IR patterns interfere with each other. This results in a massive loss of depth information. In this paper, we present a simple and powerful method to overcome these problems. We propose a stereo RGB-D camera system which uses the pros of RGB-D cameras and combine them with the pros of stereo camera systems. The idea is to utilize the IR images of each two sensors as a stereo pair to generate a depth map. The IR patterns emitted by IR projectors are exploited here to enhance the dense stereo matching even if the observed objects or surfaces are texture-less or transparent. The resulting disparity map is then fused with the depth map offered by the RGB-D sensor to fill the regions and the holes that appear because of interference, or due to transparent or reflective objects. Our results show that the density of depth information is increased especially for transparent, shiny or matte objects. Y1 - 2014 SN - 978-3-319-13559-5 (Print) ; 978-3-319-13560-1 (E-Book) U6 - https://doi.org/10.1007/978-3-319-13560-1_33 SP - 409 EP - 421 PB - Springer CY - München ER - TY - CHAP A1 - Heuermann, Holger A1 - Finger, Torsten T1 - 2.45 GHz Plasma Powered Spark Plug by Thermal and EM-Optimization Y1 - 2014 N1 - Ansys High Frequency Simulation Conference - AHFSC 2014, Munich; 02/2014 ER - TY - JOUR A1 - Stulpe, Werner T1 - From the attempt of certain classical reformulations of quantum mechanics to quasi-probability representations JF - Journal of Mathematical Physics N2 - The concept of an injective affine embedding of the quantum states into a set of classical states, i.e., into the set of the probability measures on some measurable space, as well as its relation to statistically complete observables is revisited, and its limitation in view of a classical reformulation of the statistical scheme of quantum mechanics is discussed. In particular, on the basis of a theorem concerning a non-denseness property of a set of coexistent effects, it is shown that an injective classical embedding of the quantum states cannot be supplemented by an at least approximate classical description of the quantum mechanical effects. As an alternative approach, the concept of quasi-probability representations of quantum mechanics is considered. Y1 - 2014 U6 - https://doi.org/10.1063/1.4861939 SN - 222-488 N1 - bereits unter gleichem Titel aufgenommen bei arxiv : http://arxiv.org/pdf/1307.2314.pdf VL - 55 IS - 1 PB - AIP Publishing CY - College Park, Md. ER -