TY - CHAP A1 - Koch, Claudia A1 - Poghossian, Arshak A1 - Wege, Christina A1 - Schöning, Michael Josef ED - Wege, Christina T1 - TMV-Based Adapter Templates for Enhanced Enzyme Loading in Biosensor Applications T2 - Virus-Derived Nanoparticles for Advanced Technologies N2 - Nanotubular tobacco mosaic virus (TMV) particles and RNA-free lower-order coat protein (CP) aggregates have been employed as enzyme carriers in different diagnostic layouts and compared for their influence on biosensor performance. In the following, we describe a label-free electrochemical biosensor for improved glucose detection by use of TMV adapters and the enzyme glucose oxidase (GOD). A specific and efficient immobilization of streptavidin-conjugated GOD ([SA]-GOD) complexes on biotinylated TMV nanotubes or CP aggregates was achieved via bioaffinity binding. Glucose sensors with adsorptively immobilized [SA]-GOD, and with [SA]-GOD cross-linked with glutardialdehyde, respectively, were tested in parallel on the same sensor chip. Comparison of these sensors revealed that TMV adapters enhanced the amperometric glucose detection remarkably, conveying highest sensitivity, an extended linear detection range and fastest response times. These results underline a great potential of an integration of virus/biomolecule hybrids with electronic transducers for applications in biosensorics and biochips. Here, we describe the fabrication and use of amperometric sensor chips combining an array of circular Pt electrodes, their loading with GOD-modified TMV nanotubes (and other GOD immobilization methods), and the subsequent investigations of the sensor performance. KW - Tobacco mosaic virus (TMV) KW - Coat protein KW - Enzyme nanocarrier KW - Glucose biosensor KW - Glucose oxidase Y1 - 2018 SN - 978-1-4939-7808-3 U6 - http://dx.doi.org/10.1007/978-1-4939-7808-3 N1 - Methods in Molecular Biology, vol 1776 SP - 553 EP - 568 PB - Humana Press CY - New York, NY ER - TY - CHAP A1 - Knott, Thomas C. A1 - Sofronia, Raluca E. A1 - Gerressen, Marcus A1 - Law, Yuen A1 - Davidescu, Arjana A1 - Savii, George G. A1 - Gatzweiler, Karl-Heinz A1 - Staat, Manfred A1 - Kuhlen, Torsten W. T1 - Preliminary bone sawing model for a virtual reality-based training simulator of bilateral sagittal split osteotomy T2 - Biomedical simulation : 6th International Symposium, ISBMS 2014, Strasbourg, France, October 16-17, 2014 : proceedings (Lecture notes in computer science : vol. 8789) N2 - Successful bone sawing requires a high level of skill and experience, which could be gained by the use of Virtual Reality-based simulators. A key aspect of these medical simulators is realistic force feedback. The aim of this paper is to model the bone sawing process in order to develop a valid training simulator for the bilateral sagittal split osteotomy, the most often applied corrective surgery in case of a malposition of the mandible. Bone samples from a human cadaveric mandible were tested using a designed experimental system. Image processing and statistical analysis were used for the selection of four models for the bone sawing process. The results revealed a polynomial dependency between the material removal rate and the applied force. Differences between the three segments of the osteotomy line and between the cortical and cancellous bone were highlighted. KW - Bone sawing KW - virtual reality KW - training simulator Y1 - 2014 SN - 978-3-319-12057-7 (Online) SN - 978-3-319-12056-0 (Print) U6 - http://dx.doi.org/10.1007/978-3-319-12057-7_1 SP - 1 EP - 10 PB - Springer CY - Cham ER - TY - CHAP A1 - Knoche, K. F. A1 - Kruska, Martin A1 - Weber, P. A1 - Kuperjans, Isabel ED - Schulz, Werner F. T1 - Energiemanagement T2 - Lexikon Nachhaltiges Wirtschaften. - (Lehr- und Handbücher zur ökologischen Unternehmensführung und Umweltökonomie) Y1 - 2001 SN - 3-486-24523-6 SP - 88 EP - 92 PB - Oldenbourg CY - München [u.a.] ER - TY - CHAP A1 - Klocke, Martina A1 - Katz, Christiane T1 - Heterogenität von MINT-Studierenden als Herausforderung T2 - Tagungsband zum 3. Symposium zur Hochschullehre in den MINT-Fächern Y1 - 2017 SP - 31 EP - 36 PB - Technische Hochschule Nürnberg Georg Simon Ohm CY - Nürnberg ER - TY - CHAP A1 - Klocke, Martina T1 - Schulter an Schulter – Zusammenarbeit in einem differenzierten Hochschulsystem T2 - Lehre und Lehrentwicklung an Fachhochschulen – Festschrift für Prof. Dr. med. W. Huhn Y1 - 2018 SN - 978-3-8309-3782-1 SP - 75 EP - 80 PB - Waxmann CY - Münster ER - TY - CHAP A1 - Kirsch, Hans-Jürgen A1 - Bassen, Yasmine T1 - IGW RS HFA 21 : konzeptionelle Lösung oder Einzelfall? ; Erfolg bei Spenden sammelnden Organisationen ; eine bilanztheoretische Untersuchung T2 - Jahrbuch für Controlling und Rechnungswesen. Vol. 29 Y1 - 2013 SP - 355 EP - 369 PB - LexisNexis, ARD Orac CY - Wien ER - TY - CHAP A1 - Kirchner, Patrick A1 - Reisert, Steffen A1 - Schöning, Michael Josef T1 - Calorimetric gas sensors for hydrogen peroxide monitoring in aseptic food processes T2 - Gas sensing fundamentals. (Springer Series on Chemical Sensors and Biosensors ; 15) N2 - For the sterilisation of aseptic food packages it is taken advantage of the microbicidal properties of hydrogen peroxide (H2O2). Especially, when applied in vapour phase, it has shown high potential of microbial inactivation. In addition, it offers a high environmental compatibility compared to other chemical sterilisation agents, as it decomposes into oxygen and water, respectively. Due to a lack in sensory detection possibilities, a continuous monitoring of the H2O2 concentration was recently not available. Instead, the sterilisation efficacy is validated using microbiological tests. However, progresses in the development of calorimetric gas sensors during the last 7 years have made it possible to monitor the H2O2 concentration during operation. This chapter deals with the fundamentals of calorimetric gas sensing with special focus on the detection of gaseous hydrogen peroxide. A sensor principle based on a calorimetric differential set-up is described. Special emphasis is given to the sensor design with respect to the operational requirements under field conditions. The state-of-the-art regarding a sensor set-up for the on-line monitoring and secondly, a miniaturised sensor for in-line monitoring are summarised. Furthermore, alternative detection methods and a novel multi-sensor system for the characterisation of aseptic sterilisation processes are described. KW - Calorimetric gas sensor KW - Hydrogen peroxide KW - Multi-sensor system Y1 - 2014 SN - 978-3-642-54518-4 (Print) ; 978-3-642-54519-1 (Online) U6 - http://dx.doi.org/10.1007/5346_2013_51 SP - 279 EP - 309 PB - Springer CY - Heidelberg ER - TY - CHAP A1 - Kallweit, Stephan A1 - Gottschalk, Michael A1 - Walenta, Robert T1 - ROS based safety concept for collaborative robots in industrial applications T2 - Advances in robot design and intelligent control : proceedings of the 24th International Conference on Robotics in Alpe-Adria-Danube Region (RAAD). (Advances in intelligent systems and computing ; 371) N2 - The production and assembly of customized products increases the demand for flexible automation systems. One approach is to remove the safety fences that separate human and industrial robot to combine their skills. This collaboration possesses a certain risk for the human co-worker, leading to numerous safety concepts to protect him. The human needs to be monitored and tracked by a safety system using different sensors. The proposed system consists of a RGBD camera for surveillance of the common working area, an array of optical distance sensors to compensate shadowing effects of the RGBD camera and a laser range finder to detect the co-worker when approaching the work cell. The software for collision detection, path planning, robot control and predicting the behaviour of the co-worker is based on the Robot Operating System (ROS). A first prototype of the work cell shows that with advanced algorithms from the field of mobile robotics a very flexible safety concept can be realized: the robot not simply stops its movement when detecting a collision, but plans and executes an alternative path around the obstacle. KW - Collaborative robot KW - Human-Robot interaction KW - Safety concept KW - Workspace monitoring KW - Path planning Y1 - 2016 SN - 978-3-319-21289-0 (Print) ; 978-3-319-21290-6 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-319-21290-6_3 SP - 27 EP - 35 PB - Springer CY - Cham ER - TY - CHAP A1 - Jordan, Frank A1 - Katz, Christiane A1 - Pieper, Martin T1 - Online-Kollaboration in der Mathematik: Ein Design-Based-Research-Projekt T2 - Forschungsimpulse für hybrides Lehren und Lernen an Hochschulen N2 - Die Studie erörtert anhand eines Fallbeispiels aus der Mathematik für Ingenieur*innen, wie didaktische Gestaltungsprinzipien für Soziale Präsenz, Kollaboration und das Lösen von praxisnahen Problemen mit mathematischem Denken in einer Online-Umgebung aussehen können. Hierfür zieht der Beitrag den forschungsmethodologischen Rahmen Design-Based Research (DBR) hinzu und berichtet über Zwischenergebnisse. DBR wird an dieser Stelle als eine systematische Herangehensweise an kurzfristige Lehrveränderungen und als Chance auf dem Weg zu einer neuen Hochschullehre nach der COVID-19-Pandemie dargestellt, die theoretische und empirische Erkenntnisse mit Praxisverknüpfung und -relevanz vereint. Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:832-cos4-9465 SP - 245 EP - 261 PB - TH Köln CY - Köln ER - TY - CHAP A1 - Janser, Frank T1 - Zukunftssicherung im Mittelstand - Kooperation zwischen der Stacke Tresorbau GmbH und der Fachhochschule Aachen T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 SP - 179 EP - 183 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Jakobs, Helmut T1 - Vorwort T2 - Vielen Dank für Ihren Einkauf : Konsumkultur aus Sicht von Design, Kunst und Medien Y1 - 2012 SN - 978-3-8376-2170-9 SP - 7 PB - Transcript Verlag CY - Bielefeld ER - TY - CHAP A1 - Ibanez-Sanchez, Gema A1 - Wolf, Martin T1 - Interactive Process Mining-Induced Change Management Methodology for Healthcare T2 - Interactive Process Mining in Healthcare N2 - The adoption of the Digital Health Transformation is a tremendous paradigm change in health organizations, which is not a trivial process in reality. For that reason, in this chapter, it is proposed a methodology with the objective to generate a changing culture in healthcare organisations. Such a change culture is essential for the successful implementation of any supporting methods like Interactive Process Mining. It needs to incorporate (mostly) new ways of team-based and evidence-based approaches for solving structural problems in a digital healthcare environment. KW - Methodology KW - Change culture KW - Lean thinking KW - Interactive process mining KW - Objective data Y1 - 2020 SN - 978-3-030-53993-1 (Online) SN - 978-3-030-53992-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-030-53993-1_16 SP - 267 EP - 293 PB - Springer CY - Cham ER - TY - CHAP A1 - Hüning, Felix ED - Schmitz, Günter T1 - PowerMOSFETs für Elektromotoren im Automobil : Vom Fensterheber zum EPS T2 - Elektronik im Kraftfahrzeug : Innovationen bei Systemen und Komponenten ; mit 7 Tabellen Y1 - 2012 SN - 978-3-8169-3110-2 N1 - Haus der Technik Fachbuchreihe ; 123 SP - 71 EP - 81 PB - Expert Verlag CY - Renningen ER - TY - CHAP A1 - Höhne, Tim A1 - Narr, Claus ED - Schuh, Günther T1 - Konsequenzen für die überbetriebliche IT-Unterstützung T2 - Liefertreue im Maschinen- und Anlagenbau Y1 - 2006 SN - 3-926690-02-X N1 - Studie Liefertreue im Maschinen- und Anlagebau; Forschungsinstitut für Rationalisierung FIR an der RWTH Aachen; Fraunhofer-Institut für Produktionstechnik und Automatisierung IPA; Laboratorium für Werkzeugmaschinen und Betriebslehre WZL der RWTH Aachen ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Faber, Christian T1 - Lighthouse project for North-Rhine Westfalia - Solar thermal R & D Power Planet in Jülich T2 - Energy security, climate change and sustainable development / ed. Jyotirmay Mathur ... Y1 - 2007 SN - 81-88342-81-5 SP - 101 EP - 116 PB - Anamaya Publ. CY - New Delhi ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Rau, Christoph A1 - Sattler, Johannes, Christoph A1 - Anthrakidis, Anette A1 - Teixeira Boura, Cristiano José A1 - O’Connor, B. A1 - Chico Caminos, R.A. A1 - Rendón, C. A1 - Hilger, P. T1 - Concentrating solar power T2 - Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications N2 - The focus of this chapter is the production of power and the use of the heat produced from concentrated solar thermal power (CSP) systems. The chapter starts with the general theoretical principles of concentrating systems including the description of the concentration ratio, the energy and mass balance. The power conversion systems is the main part where solar-only operation and the increase in operational hours. Solar-only operation include the use of steam turbines, gas turbines, organic Rankine cycles and solar dishes. The operational hours can be increased with hybridization and with storage. Another important topic is the cogeneration where solar cooling, desalination and of heat usage is described. Many examples of commercial CSP power plants as well as research facilities from the past as well as current installed and in operation are described in detail. The chapter closes with economic and environmental aspects and with the future potential of the development of CSP around the world. KW - Central receiver power plant KW - Concentrated systems KW - Gas turbine KW - Hybridization KW - Power conversion systems Y1 - 2022 SN - 978-0-12-819734-9 SP - 670 EP - 724 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Rau, Christoph A1 - Sattler, Johannes, Christoph A1 - Anthrakidis, Anette A1 - Teixeira Boura, Cristiano José A1 - O’Connor, B. A1 - Caminos, R.A. Chico A1 - Rendón, C. A1 - Hilger, P. T1 - Concentrating Solar Power T2 - Earth systems and environmental sciences N2 - The focus of this chapter is the production of power and the use of the heat produced from concentrated solar thermal power (CSP) systems. The chapter starts with the general theoretical principles of concentrating systems including the description of the concentration ratio, the energy and mass balance. The power conversion systems is the main part where solar-only operation and the increase in operational hours. Solar-only operation include the use of steam turbines, gas turbines, organic Rankine cycles and solar dishes. The operational hours can be increased with hybridization and with storage. Another important topic is the cogeneration where solar cooling, desalination and of heat usage is described. Many examples of commercial CSP power plants as well as research facilities from the past as well as current installed and in operation are described in detail. The chapter closes with economic and environmental aspects and with the future potential of the development of CSP around the world. KW - Central receiver power plant KW - Concentrated systems KW - Concentrating solar power KW - Fresnel power plant KW - Gas turbine Y1 - 2021 SN - 978-0-12-409548-9 U6 - http://dx.doi.org/10.1016/B978-0-12-819727-1.00089-3 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Rau, Christoph A1 - Sattler, Johannes, Christoph A1 - Anthrakidis, Anette A1 - Teixeira Boura, Cristiano José A1 - O'Connor, P. A1 - Hilger, Patrick T1 - Concentrating solar power T2 - Comprehensive renewable energy / ed. Ali Sayigh. Vol. 3: Solar thermal systems: components and applications Y1 - 2012 SN - 978-0-08-087872-0 U6 - http://dx.doi.org/10.1016/B978-0-08-087872-0.00319-X VL - 3 SP - 595 EP - 636 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Göttsche, Joachim A1 - Sauerborn, Markus A1 - Kaufhold, O. T1 - High Concentration Solar Collectors T2 - Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications N2 - Solar thermal concentrated power is an emerging technology that provides clean electricity for the growing energy market. To the solar thermal concentrated power plant systems belong the parabolic trough, the Fresnel collector, the solar dish, and the central receiver system. For high-concentration solar collector systems, optical and thermal analysis is essential. There exist a number of measurement techniques and systems for the optical and thermal characterization of the efficiency of solar thermal concentrated systems. For each system, structure, components, and specific characteristics types are described. The chapter presents additionally an outline for the calculation of system performance and operation and maintenance topics. One main focus is set to the models of components and their construction details as well as different types on the market. In the later part of this article, different criteria for the choice of technology are analyzed in detail. KW - Central receiver system KW - Concentrated solar collector KW - Solar dish KW - Solar concentration Y1 - 2022 SN - 978-0-12-819734-9 U6 - http://dx.doi.org/10.1016/B978-0-12-819727-1.00058-3 SP - 198 EP - 245 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Göttsche, Joachim A1 - Sauerborn, Markus T1 - High concentration solar collectors T2 - Comprehensive renewable energy / ed. Ali Sayigh. Vol. 3: Solar thermal systems: components and applications N2 - Solar thermal concentrated power is an emerging technology that provides clean electricity for the growing energy market. To the solar thermal concentrated power plant systems belong the parabolic trough, the Fresnel collector, the solar dish, and the central receiver system. For high-concentration solar collector systems, optical and thermal analysis is essential. There exist a number of measurement techniques and systems for the optical and thermal characterization of the efficiency of solar thermal concentrated systems. For each system, structure, components, and specific characteristics types are described. The chapter presents additionally an outline for the calculation of system performance and operation and maintenance topics. One main focus is set to the models of components and their construction details as well as different types on the market. In the later part of this chapter, different criteria for the choice of technology are analyzed in detail. KW - Central receiver system KW - Concentrated solar collector KW - Fresnel collector KW - Optical and thermal analysis KW - Solar concentration Y1 - 2012 SN - 978-0-08-087873-7 U6 - http://dx.doi.org/10.1016/B978-0-08-087872-0.00306-1 VL - 3 SP - 165 EP - 209 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Hoffmann, Christoph P. A1 - Lindemann, Markus T1 - Logistik und internetbasiertes Electronic Commerce T2 - Schweizer Logistik-Katalog : Logistik, fördern, lagern, verteilen. 1999 Y1 - 1999 SP - 16 EP - 19 PB - Binkert CY - Lauffenburg ER - TY - CHAP A1 - Hoepner, Gert A1 - Schminke, Lutz H. T1 - Dialog-Marketing – 2 in 1 – mehr als 3-fach erfolgreich T2 - Marketing in Forschung und Praxis : [Jubiläumsausgabe zum 40-jährigen Bestehen der Arbeitsgemeinschaft für Marketing] / hrsg. von Günter Hofbauer ... Y1 - 2013 SN - 978-3-942171-98-4 SP - 375 EP - 396 PB - Uni-Ed. CY - Berlin ER - TY - CHAP A1 - Hirt, Gerhard A1 - Bleck, Wolfgang A1 - Bobzin, Kirsten A1 - Schleser, Markus A1 - [u.a.], T1 - Hybride Produktionssysteme T2 - Integrative Produktionstechnik für Hochlohnländer / hrsg. von Christian Brecher N2 - Während die virtuelle Produktentstehungskette große Gestaltungsfreiräume bietet, ist die reale Produktentstehungskette durch wesentlich mehr Randbedingungen gekennzeichnet, die nicht oder nur ansatzweise beeinflussbar sind. Die Realisierung des aus logistischer Sicht optimalen One-Piece-Flow bei gleichzeitiger Steigerung von Flexibilität und Produktivität sowie des Verschiebens der Grenze des technologisch Machbaren müssen in zukünftigen Forschungsansätzen gleichermaßen betrachtet werden. Die Grenzverschiebung auf Basis der Integration von Technologien ist dabei ein viel versprechender Ansatz, der es in vielen Fällen ermöglicht, in allen genannten Zielrichtungen gleichermaßen Potentiale zu erschließen. Y1 - 2011 SN - 978-3-642-20692-4 (Print) ; 978-3-642-20693-1 (E-Book) U6 - http://dx.doi.org/10.1007/978-3-642-20693-1_5 SP - 465 EP - 745 PB - Springer CY - Berlin [u.a.] ER - TY - CHAP A1 - Hirsch, G. A1 - Wahle, Michael T1 - Auslegungskriterien für Dynamische Schwingungsdämpfer für schwach gedämpfte elastische Strukturen unter Berücksichtigung einer der Masseverteilung nicht proportionalen Zusatzdämpfung T2 - Hans Ebner : Gedächtnis-Kolloquium am 27./28. Oktober 1977 in Aachen. - (Mitteilung aus dem Institut für Leichtbau, Aachen ; 1) Y1 - 1978 SP - 374 EP - 400 CY - Aachen ER - TY - CHAP A1 - Hinke, Christian A1 - Vervier, Luisa A1 - Brauner, Philipp A1 - Schneider, Sebastian A1 - Steuer-Dankert, Linda A1 - Ziefle, Martina A1 - Leicht-Scholten, Carmen T1 - Capability configuration in next generation manufacturing T2 - Forecasting next generation manufacturing : digital shadows, human-machine collaboration, and data-driven business models N2 - Industrial production systems are facing radical change in multiple dimensions. This change is caused by technological developments and the digital transformation of production, as well as the call for political and social change to facilitate a transformation toward sustainability. These changes affect both the capabilities of production systems and companies and the design of higher education and educational programs. Given the high uncertainty in the likelihood of occurrence and the technical, economic, and societal impacts of these concepts, we conducted a technology foresight study, in the form of a real-time Delphi analysis, to derive reliable future scenarios featuring the next generation of manufacturing systems. This chapter presents the capabilities dimension and describes each projection in detail, offering current case study examples and discussing related research, as well as implications for policy makers and firms. Specifically, we discuss the benefits of capturing expert knowledge and making it accessible to newcomers, especially in highly specialized industries. The experts argue that in order to cope with the challenges and circumstances of today’s world, students must already during their education at university learn how to work with AI and other technologies. This means that study programs must change and that universities must adapt their structural aspects to meet the needs of the students. Y1 - 2022 SN - 978-3-031-07733-3 U6 - http://dx.doi.org/10.1007/978-3-031-07734-0_6 SP - 95 EP - 106 PB - Springer CY - Cham ER - TY - CHAP A1 - Heuermann, Holger A1 - Finger, Torsten ED - Günther, Michael T1 - Microwave Spark Plug for Very High-Pressure Conditions T2 - Ignition systems for gasoline engines Y1 - 2014 SP - 269 EP - 282 PB - DCM Druck CY - Meckenheim ER - TY - CHAP A1 - Herrmann, Ulf A1 - Kearney, D. A1 - Röger, M. A1 - Prahl, C. T1 - System performance measurements T2 - The Performance of Concentrated Solar Power (CSP) Systems : Modelling, Measurement and Assessment N2 - This chapter introduces performance and acceptance testing and describes state-of-the-art tools, methods, and instruments to assess the plant performance or realize plant acceptance testing. The status of the development of standards for performance assessment is given. KW - Performance measurement KW - Acceptance tests KW - Plant efficiency Y1 - 2017 SN - 978-0-08-100448-7 U6 - http://dx.doi.org/https://doi.org/10.1016/B978-0-08-100447-0.00005-5 SP - 115 EP - 165 PB - Woodhead Publishing CY - Duxford ER - TY - CHAP A1 - Henderson, Colin J. A1 - Wolf, C. Roland A1 - Scheer, Nico ED - Woolf, Thomas F. T1 - The use of transgenic animals to study drug metabolism T2 - Handbook of Drug Metabolism. 2nd Edition Y1 - 2009 SN - 978-1-4200-7647-9 SP - 637 EP - 658 PB - Informa Healthcare CY - New York ER - TY - CHAP A1 - Helsper, Christoph A1 - Fissan, H. J. A1 - Franzen, H. ED - Benarie, Michel M. T1 - Particle Size Distributions of Combustion Aerosols T2 - Atmospheric Pollution 1978 : Proceedings of the 13th International Colloquium; 25-28 April 1978; Paris, France; Edited by Michel M. Benarie N2 - It has been observed that carcinogenic polycyclic aromatic hydrocarbons (PAH) are present in the atmosphere. Combustion processes are considered the most important sources for PAH. Among these, the burning of coal produces the highest emission, but in cities with high traffic density and low meteorological exchange activities, vehicle emissions determine the immission situation, especially in narrow streets. For estimating the potential health effects caused by PAH, it is sufficient to characterize the emission of PAH with respect to their physical state, concentrations, and, as far as the particulate phase is concerned, size distribution. The size distribution is important for transport phenomena, inhalation, and deposition in the respiratory tract. These parameters mainly depend on the combustion system, on system operating conditions, on the exhaust system, and on exhaust cooling conditions. At exhaust-gas temperatures in the range of ambient air temperatures, almost the whole emission of PAH is made up of particulate matter. Y1 - 1978 SN - 0-444-41691-9 U6 - http://dx.doi.org/10.1016/S0166-1116(08)71583-8 SP - 263 EP - 266 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Helsper, Christoph A1 - Dressler, Jörg ED - Gail, Lothar ED - Gommel, Udo ED - Hortig, Hans-Peter T1 - Partikelmesstechnik T2 - Reinraumtechnik N2 - Der Schutz von Produkten vor der Kontamination durch Partikel gilt als eine zentrale Aufgabe der Reinraumtechnik. Da es dabei um Kontaminationseffekte weit unterhalb der visuellen Wahrnehmbarkeit geht, braucht es leistungsfähige Verfahren, um die Messgröße „Partikelkontamination“ über den gesamten Bereich, den Anwender fordern, präzise zu bestimmen. Neben der Partikelhäufigkeit ist dabei die Größe der Partikel, die sowohl das Transportverhalten wie auch die mögliche Wirkung auf das Produkt beeinflusst, von entscheidender Bedeutung. Ferner kann es für die Ermittlung von Kontaminationsquellen von Interesse sein, die Form und die chemische Natur der Partikel zu bestimmen (z. B. textile Fasern, Metallabrieb, flüssige Tröpfchen). Die Partikelhäufigkeit wird üblicherweise als Konzentration, d. h. bezogen auf das analysierte Gasvolumen angegeben. Bei den in reinen Technologien üblichen niedrigen Konzentrationen dient als Häufigkeitsmaß die Partikelanzahlkonzentration, also die Partikelanzahl pro Volumeneinheit des Trägermediums. Y1 - 2012 SN - 978-3-642-19435-1 U6 - http://dx.doi.org/10.1007/978-3-642-19435-1_3 VL - 2012 SP - 69 EP - 95 PB - Springer CY - Berlin ET - 3 ER - TY - CHAP A1 - Helmig, Ilka A1 - Heiming, Eva T1 - Fünf Fragen an Ilka Helmig T2 - Design : Studienführer mit Olive ; die Ausbildungsstätten und Studiengänge in Deutschland KW - Designstudium Y1 - 2009 SN - 978-3-937787-19-0 SP - 41 PB - Hellblau-Verlag CY - [Essen, Ruhr] ER - TY - CHAP A1 - Helmig, Ilka A1 - Boonzaaijer, Karel T1 - Growing 48 hours : design experiment in an aircraft hangar ... T2 - Papercraft [1] : design and art with paper KW - Papierkunst KW - Aktionskunst KW - Studienarbeit Y1 - 2009 SN - 978-3-89955-251-5 SP - 224 PB - Gestalten Verlag CY - Berlin ER - TY - CHAP A1 - Helmig, Ilka ED - Klanten, Robert T1 - Tristan und Isolde, Samson und Dalila, Capriccio : 3D illustration for posters of Cologne Opera T2 - Papercraft [1] : design and art with paper KW - Papierkunst Y1 - 2009 SN - 978-3-89955-251-5 SP - 202 PB - Gestalten Verlag CY - Berlin ER - TY - CHAP A1 - Helmig, Ilka T1 - Friendship : editorial illustration T2 - Papercraft 2 : design and art with paper KW - Papierkunst KW - Illustration Y1 - 2011 SN - 978-3-89955-333-8 SP - 237 PB - Gestalten Verlag CY - Berlin ER - TY - CHAP A1 - Heimes, Heiner Hans A1 - Kampker, Achim A1 - Kehrer, Mario A1 - Dünnwald, Simon A1 - Heetfeld, Lennart A1 - Polzenberg, Jens A1 - Budde, Lucas A1 - Keusen, Maximilian A1 - Pandey, Rahul A1 - Röth, Thilo ED - Kampker, Achim ED - Heimes, Heiner Hans T1 - Fahrzeugstruktur T2 - Elektromobilität: Grundlagen einer Fortschrittstechnologie N2 - Um sowohl Treibhausgas-Emissionen zu verringern als auch Kraftstoffressourcen zu schonen, wird zunehmend an einer Transformation konventionell angetriebener Kraftfahrzeuge hin zu elektrifizierten Antriebskonzepten gearbeitet. Basierend auf herkömmlichen Fahrzeugen mit Verbrennungsmotor wurde eine Vielzahl neuer Antriebssysteme mit verschiedenem Elektrifizierungsgrad entwickelt. Mitte der 1990er-Jahre kamen erste Fahrzeuge mit einem Hybridantrieb auf den Markt. Die Kombination aus Verbrennungs- und Elektromotor erlaubt eine Verbrauchsreduktion und Bremsenergierückgewinnung sowie lokal emissionsfreies Fahren. Y1 - 2023 SN - 978-3-662-65811-6 (Print) SN - 978-3-662-65812-3 (Online) U6 - http://dx.doi.org/10.1007/978-3-662-65812-3_5 N1 - Corresponding author: Heiner Hans Heimes SP - 69 EP - 106 PB - Springer Vieweg CY - Berlin ER - TY - CHAP A1 - Heimes, Heiner Hans A1 - Kampker, Achim A1 - Dorn, Benjamin A1 - Kehrer, Mario A1 - Dünnwald, Simon A1 - Badura, Dennis A1 - Terren, Maximilian A1 - Röth, Thilo ED - Kampker, Achim ED - Heimes, Heiner Hans T1 - Produktionsprozesse der Fahrzeugstruktur T2 - Elektromobilität: Grundlagen einer Fortschrittstechnologie Y1 - 2023 SN - 978-3-662-65811-6 (Print) SN - 978-3-662-65812-3 (Online) U6 - http://dx.doi.org/10.1007/978-3-662-65812-3_13 N1 - Corresponding author: Benjamin Dorn SP - 227 EP - 247 PB - Springer Vieweg CY - Berlin ER - TY - CHAP A1 - Hebel, Christoph A1 - Herrmann, Ulf A1 - Ritz, Thomas A1 - Röth, Thilo A1 - Anthrakidis, Anette A1 - Böker, Jörg A1 - Franzke, Till A1 - Grodzki, Thomas A1 - Merkens, Torsten A1 - Schöttler, Mirjam T1 - FlexSHARE – Methodisches Framework zur innovativen Gestaltung der urbanen Mobilität durch Sharing- Angebote T2 - Transforming Mobility – What Next? N2 - Das Ziel des INTERREG-Projektes „SHAREuregio“ (FKZ: 34.EFRE-0300134) ist es, grenzüberschreitende Mobilität in der Euregio Rhein-Maas-Nord zu ermöglichen und zu fördern. Dazu soll ein elektromobiles Car- und Bikesharing- System entwickelt und in der Stadt Mönchengladbach, im Kreis Viersen sowie in den Gemeinden Roermond und Venlo (beide NL) zusammen mit den Partnern Wirtschaftsförderung Mönchengladbach, Wirtschaftsförderung für den Kreis Viersen, NEW AG, Goodmoovs (NL), Greenflux (NL) und der FH Aachen implementiert werden. Zunächst richtet sich das Angebot, bestehend aus 40 Elektroautos und 40 Elektrofahrrädern, an Unternehmen und wird nach einer Erprobungsphase, mit einer größeren Anzahl an Fahrzeugen, auch für Privatpersonen verfügbar gemacht werden. Die Fahrzeuge stehen bei den jeweiligen Anwendungspartnern in Deutschland und den Niederlanden. Im Rahmen dieses Projektes hat die FH Aachen „FlexSHARE“ entwickelt – ein methodisches Framework zur innovativen Gestaltung urbaner Sharing- Angebote. Das Framework ermöglicht es, anhand von messbaren Kenngrößen, bedarfsgerechte und auf die Region abgestimmte Sharing-Systeme zu entwickeln. Y1 - 2022 SN - 978-3-658-36429-8 U6 - http://dx.doi.org/10.1007/978-3-658-36430-4_10 N1 - Tagungsband zum 13. Wissenschaftsforum Mobilität, Beiträge des Wissenschaftsforums SP - 153 EP - 169 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Hebel, Christoph T1 - Mehrwert T2 - Unser Dorf hat Zukunft Y1 - 2014 SP - 6 EP - 7 PB - StädteRegion Aachen CY - Aachen ER - TY - CHAP A1 - Hauk, Joachim A1 - Czarnecki, Christian A1 - Dietze, Christian ED - Rusnjak, Andreas ED - Schallmo, Daniel R. A. T1 - Prozessorientierte Messung der Customer Experience am Beispiel der Telekommunikationsindustrie T2 - Customer Experience im Zeitalter des Kunden : Best Practices, Lessons Learned und Forschungsergebnisse N2 - Hohe Wettbewerbsintensität und gestiegene Kundenanforderungen erfordern bei Telekommunikationsunternehmen eine aktive Gestaltung der Customer Experience (CX). Ein wichtiger Aspekt dabei ist die CX-Messung. Traditionelle Zufriedenheitsmessungen sind oft nicht ausreichend, um die Kundenerfahrung in komplexen Prozessen vollständig zu erfassen. Daher wird in diesem Kapitel eine prozessübergreifende Referenzlösung zur CX-Messung am Beispiel der Telekommunikationsindustrie vorgeschlagen. Ausgangspunkt ist ein industriespezifisches Prozessmodell, das sich an dem Referenzmodell eTOM orientiert. Dieses wird um Messpunkte erweitert, die Schwachstellen in Bezug auf die CX identifizieren. Für die erkannten Schwachstellen werden über eine Referenzmatrix mögliche Auslöser abgeleitet und anhand von typischen Geschäftsfallmengen bewertet. Somit ist eine direkte Zuordnung und Erfolgsmessung konkreter Maßnahmen zur Behebung der Schwachstellen möglich. Die so entwickelte Referenzlösung wurde im Projekt K1 bei der Deutschen Telekom erfolgreich umgesetzt. Details zur Umsetzung werden als Fallstudien dargestellt. Y1 - 2018 SN - 978-3-658-18961-7 SN - 978-3-658-18960-0 U6 - http://dx.doi.org/10.1007/978-3-658-18961-7_7 SP - 195 EP - 216 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Hahn, Thomas A1 - Kelly, Svenja A1 - Muffler, Kai A1 - Tippkötter, Nils A1 - Ulber, Roland ED - Hans-Jörg, Bart ED - Pilz, Stephan T1 - Extraction of lignocellulose and algae for the production of bulk and fine chemicals T2 - Industrial scale natural products extraction Y1 - 2011 SN - 978-3-527-32504-7 (Print) SN - 978-3-527-63512-2 (Online) U6 - http://dx.doi.org/10.1002/9783527635122 SP - 221 EP - 245 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Groß, Rolf Fritz A1 - Thulfaut, Christian A1 - Renz, Ulrich ED - Jamal, Rahman ED - Jaschinski, Hans T1 - On-Line Simulation mit LabView: Experimentelle und numerische Analyse homogener Gasphasenreaktionen aus Kraftwerksprozessen, T2 - Virtuelle Instrumente in der Praxis. Begleitband zum Kongress VIP 2000 N2 - The institute of heat transfer and air conditioning at the Aachen University of Technology operates several test facilities in order to investigate homogeneous and catalytical processes for the reduction of gaseous pollutants (e.g. nitrous oxide) of flue gases in a tempeature range up to 900°C. One test facility consists of a stainless steel reactor in which the influence of reducing additives can be investigated. The software tool, created with LabVIEW 5.01, offers the possibility to measure, visualize and control all relevant physical quantities and to gain a numerical solution of the problem by solving the one dimensional, steady state conservation equations. N2 - Die bei Kohlekraftwerksprozessen entstehenden Rauchgase enthalten einen nicht unerheblichen Teil an Schadgaskomponenten (z.B. Stickoxide), die aus dem Gasstrom entfernt werden müssen. Im Rahmen von Forschungsvorhaben des BMBF und verschiedener Industriepartner betreibt der Lehrstuhl für Wärmeübertragung und Klimatechnik der RWTH Aachen Pilotanlagen und Prüfstände für Untersuchungen auf dem Gebiet der homogenen und heterogen-katalytischen Schadstoffreduktion heißer Rauchgase bei Temperaturen bis zu 900 °C. Für die Erforschung der Minderungspotentiale geeigneter, auf Distickstoffoxid reduzierend wirkender Additive, wie Wasserstoffperoxid, oder auch Katalysatoren, befindet sich ein Reaktor in Betrieb, der eine Untersuchung der Reaktionskinetik bei der Entfernung von Schadgaskomponenten aus einem lnertgasstrom ermöglicht. Wesentlich für den Erfolg der Forschungsarbeit ist eine auf das spezielle Projekt genau abgestimmte Meß- und Regelungstechnik. Neben der Auswahl geeigneter Hardwarekomponenten ist auch die Softwareentwicklung unter einer leistungsstarken und zuverlässigen Programmierumgebung von großer Bedeutung. Hierbei dient die unter LabVIEW 5.01 entwickelte Datenerfassung- und Auswertesoftware zum einen der Messung, Visualisierung und Regelung der relevanten Temperaturen, Drücke, Konzentrationen und Volumenströme einzelner Gaskomponenten. Zum anderen ermöglicht sie parallel eine numerische Simulation der Vorgänge innerhalb des Reaktors zur Anpassung reaktionskinetischer Parameter aus den sich ergebenden Versuchsdaten durch Lösung eindimensionaler, stationärer Erhaltungsgleichungen. Y1 - 2000 SN - 3-7785-2789-4 (print) SP - 103 EP - 108 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Groß, Rolf Fritz A1 - Müller, D. A1 - Herting, D. A1 - Schneemann, A. A1 - Renz, Ulrich ED - Rahman, Jamal ED - Jaschinski, Hans T1 - Modulare Messdatenerfassung in Forschung und Lehre T2 - Virtuelle Instrumente in der Praxis : Begleitband zum Kongress VIP '97 N2 - The Lehrstuhl für Wärmeübertragung und Klimatechnik at the Aachen University of Technology operates several test facilities to investigate fundamentals of heat and mass transfer supported by the Deutsche Forschungsgemeinschaft, the Minister für Forschung und Technologie and the industry. In order to get high-resolution and reproselection of hardware components is as critical as the design of software routines to perform successful and accurate measurements. In the following the development of the measurement and control system for three different test facilities is presented and discussed. Special attention is given to the education of students within the framework of laboratories and scientific experiments. Y1 - 1997 SN - 978-3-7785-2667-5 Pp. SP - 282 EP - 288 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Groß, Rolf Fritz A1 - Hecken, M. A1 - Renz, Ulrich ED - Dittler, A. ED - Hemmer, G. ED - Kasper, G. T1 - Hot gas filtration with ceramic filter candles: experimental and numerical investigations on fluid flow during element cleaning T2 - High temperature gas cleaning. Vol. 2 N2 - Ceramic hot gas filters are widely used in combined cycles based on pressurised fluidised beds. They fulfil most of the demands with respect to cleaning efficiency and long time durability, but their operation regarding the consumption of pulse gas and energy still has to be optimised. Experimental investigations were carried out to measure the flow field, the pressure and the gas temperature inside the filter candle during pulse jet cleaning. These results are compared with the results of a numerical procedure based on a solution of the two - dimensional conservation equations for momentum and energy. The observed difficulties handling different flow regimes like highly turbulent flow as well as Darcy flow simultaneously are discussed. KW - 20 fossil-fueled power plants KW - hot gas cleanup KW - ceramics KW - filtration KW - gas flow Y1 - 1999 SN - 3-9805220-1-6 N1 - 4th International Symposium and Exhibition on Gas Cleaning at High Temperatures, 22.-24.09.1999, Karlsruhe SP - 862 EP - 873 PB - KIT Institut für Mechanische Verfahrenstechnik und Mechanik CY - Karlsruhe ER - TY - CHAP A1 - Gonsior, Daniel A1 - Hoffschmidt, Bernhard T1 - Innovative Rußfilter für LKW-Dieselmotoren (Innotrap) T2 - Feinstaubforschung in Nordrhein-Westfalen. LANUV-Fachbericht. 9 Y1 - 2008 SN - 1864-3930 SP - 13 EP - 14 PB - Landesamt für Natur, Umwelt und Verbraucherschutz Nordrhein-Westfalen CY - Recklinghausen ER - TY - CHAP A1 - Golland, Alexander A1 - Schneidereit, Peter ED - Borges, Georg ED - Werners, Brigitte T1 - Rechtliche Rahmenbedingungen des Identitätsmangements im Cloud Computing T2 - Identitätsmanagement Im Cloud Computing : Evaluation ökonomischer und Rechtlicher Rahmenbedingungen N2 - Cloud Computing wirft in zahlreichen Rechtsbereichen neuartige juristische Fragestellungen auf. Ziel der Darstellung der rechtlichen Rahmenbedingungen ist, die das Identitätsmanagement in der Cloud betreffenden Rechtsgrundlagen aus den unterschiedlichen Rechtsgebieten vorzustellen und einzuordnen, bevor im Rahmen des sechsten Kapitels die Darstellung der hieraus resultierenden Verpflichtungen in ihrer konkreten Form erfolgt. KW - Technische Schutzmaßnahmen KW - Identitätsmanagement KW - IT-Sicherheit KW - Cloud Computing KW - Datenschutz Y1 - 2018 SN - 978-3-662-55584-2 U6 - http://dx.doi.org/10.1007/978-3-662-55584-2_4 SP - 53 EP - 104 PB - Springer CY - Berlin ER - TY - CHAP A1 - Golland, Alexander A1 - Ohrtmann, Jan-Peter T1 - Video surveillance: The supervisory authorities’ view andrecent case law T2 - Turning Point in Data Protection Law Y1 - 2020 SN - 978-3-8487-6909-4 U6 - http://dx.doi.org/10.5771/9783748921561-175 SP - 175 EP - 178 PB - Nomos CY - Baden-Baden ER - TY - CHAP A1 - Golland, Alexander A1 - Baum, Michael A1 - Hamminger, Alexander A1 - Olbertz, Klaus T1 - Ein Überblick: Umsetzung der Datenschutz-Grundverordnung T2 - Das neue Datenschutzrecht in der Praxis des Steuerberaters Beitragssammlung N2 - Datenschutz und der 25.5.2018, wie ein Damoklesschwert scheinen beide Begriffe zurzeit im Raum zu stehe. Jeder weiß oder sollte zumindest um das Inkrafttreten der europäischen DSGVO am 25.5.2018 wissen. Viel wurde über wesentliche Neuerungen im Datenschutzrecht berichtet. Nicht zuletzt über gesteigerte organisatorische Anforderungen, Dokumentationspflichten und drohende Bußgelder. Doch was bedeuten diese Neuerungen ganz konkret für die Praxis des Steuerberaters? Anders als man vermuten könnte, werden die datenschutzrechtlichen Neuerungen nicht nur im Bereich der Kanzleiorganisation relevant. Auch im Steuerverwaltungsverfahren sieht sich der Steuerberater datenschutzrechtlichen Fragestellungen gegenüber, bspw. dann, wenn die Finanzbehörden bei der Verarbeitung der personenbezogenen Daten des Mandanten gegen die DSGVO verstoßen. Gleiches gilt in Bereichen des Beschäftigtendatenschutzes. Sowohl der Kanzleiinhaber selbst, als auch seine Arbeitgeber-Mandanten haben die Vorschriften des Beschäftigtendatenschutzes einzuhalten. Der Steuerberater benötigt datenschutzrechtliches Know How, welches unmittelbar seine tägliche Praxis betrifft. Andernfalls besteht das Risiko, dass dieser mit mehr Fragen, als Antworten zurück bleibt. KW - EUDSGVO KW - EU-DS-GVO KW - Datenschutz KW - Datenschutzrecht KW - Datenschutzgrundverordnung Y1 - 2018 SN - 978-3-482-67271-2 SP - 8 EP - 14 PB - NWB Verlag CY - Herne ER - TY - CHAP A1 - Golland, Alexander ED - Taeger, Jürgen ED - Gabel, Detlev T1 - Kommentierung von Artikel 94 bis 99 Datenschutz-Grundverordnung T2 - DSGVO - BDSG - TTDSG: Datenschutzgrundverordnung - Bundesdatenschutzgesetz - Telekommunikation-Telemedien-Datenschutzgesetz N2 - Das Werk kommentiert leicht verständlich, aktuell und praxisnah die DSGVO sowie das BDSG und - neu - auch das TTDSG (Telekommunikation-Telemedien-Datenschutzgesetz). Verantwortliche erhalten damit eine umfassende Darstellung mit Handlungsempfehlungen zum gesamten neuen Datenschutzrecht. Betriebliche Datenschutzbeauftragte können sich an den fundierten Kommentierungen orientieren, in denen Literatur und Rechtsprechung aktuell berücksichtigt wurden. KW - Telekommunikation-Telemedien-Datenschutzgesetz KW - Internationales Recht / Europarecht KW - Datenschutzfolgenabschätzung KW - EU-Datenschutzgrundverordnung KW - Betroffenenrechte Y1 - 2022 SN - 978-3-8005-1760-2 SP - 1575 EP - 1621 PB - Fachmedien Recht und Wirtschaft CY - Frankfurt am Main ET - 4., neu bearbeitete Auflage. 2022 ER - TY - CHAP A1 - Golland, Alexander ED - Taeger, Jürgen ED - Gabel, Detlev T1 - Kommentierung von Artikel 94 bis 99 Datenschutz-Grundverordnung T2 - DSGVO-BDSG N2 - Das Werk kommentiert leicht verständlich, aktuell und praxisnah die DSGVO wie auch das neue BDSG. Datenverarbeiter erhalten damit eine umfassende Darstellung mit Handlungsempfehlungen zum gesamten neuen Datenschutzrecht. KW - Bundesdatenschutzgesetz (2017) KW - EU-DSGVO KW - EU-Datenschutzgrundverordnung KW - Internationales Recht / Europarecht KW - Datenschutzrecht Y1 - 2019 SN - 978-3-8005-1659-9 N1 - Inhaltsverzeichnis https://d-nb.info/1149714018/04 PB - Fachmedien Recht und Wirtschaft CY - Frankfurt am Main ET - 3., völlig neue bearbeitete und wesentlich erweiterte Auflage ER - TY - CHAP A1 - Golland, Alexander T1 - Struggling with users’ consent: Economic approach to solve the issue of coupling T2 - Turning Point in Data Protection Law Y1 - 2020 SN - 978-3-8487-6909-4 U6 - http://dx.doi.org/10.5771/9783748921561-121 SP - 121 EP - 126 PB - Nomos CY - Baden-Baden ER - TY - CHAP A1 - Goldbach, Daniel A1 - Hochrein, Ulrich T1 - Functional Safety Management und Analysemethoden in der Entwicklung eines sicherheitskritischen Systems im Automobil T2 - Diagnose in mechatronischen Fahrzeugsystemen IV : neue Verfahren für Test, Prüfung und Diagnose von E/E-Systemen im Kfz : [anlässlich der 5. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen"] Y1 - 2011 SN - 978-3-8169-3068-6 SP - 175 EP - 194 PB - Expert Verlag CY - Renningen ER - TY - CHAP A1 - Goldbach, Daniel T1 - Diagnosemaßnahmen in der funktionalen Sicherheit T2 - Diagnose in mechatronischen Fahrzeugsystemen, VI : neue Verfahren für Test, Prüfung und Diagnose von E/E-Systemen im Kfz : 7. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen". Bernhard Bäker ... (Hrsg.) Y1 - 2013 SN - 978-3-8169-3221-5 SP - 179 EP - 198 PB - Expert Verlag CY - Renningen ER - TY - CHAP A1 - Goldbach, Daniel T1 - Zuverlässigkeitsanalyse zur Verifikation der Einhaltung von quantitativen Sicherheitsanforderungen. T2 - Diagnose in mechatronischen Fahrzeugsystemen V : neue Verfahren für Test, Prüfung und Diagnose von E/E-Systemen im Kfz ; [anlässlich der 6. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen" in Dresden]. Bernard Bäker ... (Hrsg.) Y1 - 2012 SN - 978-3-8169-3149-2 SP - 116 EP - 132 PB - Expert Verlag CY - Renningen ER - TY - CHAP A1 - Goh, Kheng Lim A1 - Topçu, Murat A1 - Madabhushi, Gopal S. P. A1 - Staat, Manfred ED - Maia, Fatima Raquel Azevedo ED - Miguel Oliveira, J. ED - Reis, Rui L. T1 - Collagen fibril reinforcement in connective tissue extracellular matrices T2 - Handbook of the extracellular matrix N2 - The connective tissues such as tendons contain an extracellular matrix (ECM) comprising collagen fibrils scattered within the ground substance. These fibrils are instrumental in lending mechanical stability to tissues. Unfortunately, our understanding of how collagen fibrils reinforce the ECM remains limited, with no direct experimental evidence substantiating current theories. Earlier theoretical studies on collagen fibril reinforcement in the ECM have relied predominantly on the assumption of uniform cylindrical fibers, which is inadequate for modelling collagen fibrils, which possessed tapered ends. Recently, Topçu and colleagues published a paper in the International Journal of Solids and Structures, presenting a generalized shear-lag theory for the transfer of elastic stress between the matrix and fibers with tapered ends. This paper is a positive step towards comprehending the mechanics of the ECM and makes a valuable contribution to formulating a complete theory of collagen fibril reinforcement in the ECM. KW - Connective tissues KW - Extracellular matrix (ECM) KW - Collagen fibrils KW - Mechanical stability KW - Tapered ends Y1 - 2023 SN - 978-3-030-92090-6 (Print) SN - 978-3-030-92090-6 (Online) U6 - http://dx.doi.org/10.1007/978-3-030-92090-6_6-1 SP - 1 EP - 20 PB - Springer Nature CY - Cham ER - TY - CHAP A1 - Goeckel, Tom A1 - Schiffer, Stefan A1 - Wagner, Hermann A1 - Lakemeyer, Gerhard T1 - The Video Conference Tool Robot ViCToR T2 - Intelligent Robotics and Applications : 8th International Conference, ICIRA 2015, Portsmouth, UK, August 24-27, 2015, Proceedings, Part II N2 - We present a robotic tool that autonomously follows a conversation to enable remote presence in video conferencing. When humans participate in a meeting with the help of video conferencing tools, it is crucial that they are able to follow the conversation both with acoustic and visual input. To this end, we design and implement a video conferencing tool robot that uses binaural sound source localization as its main source to autonomously orient towards the currently talking speaker. To increase robustness of the acoustic cue against noise we supplement the sound localization with a source detection stage. Also, we include a simple onset detector to retain fast response times. Since we only use two microphones, we are confronted with ambiguities on whether a source is in front or behind the device. We resolve these ambiguities with the help of face detection and additional moves. We tailor the system to our target scenarios in experiments with a four minute scripted conversation. In these experiments we evaluate the influence of different system settings on the responsiveness and accuracy of the device. Y1 - 2015 SN - 978-3-319-22876-1 U6 - http://dx.doi.org/10.1007/978-3-319-22876-1_6 N1 - Lecture Notes in Computer Science ; 9245 SP - 61 EP - 73 PB - Springer ER - TY - CHAP A1 - Gligorevic, Snjezana A1 - Epple, Ulrich A1 - Schnell, Michael T1 - The LDACS1 physical layer design T2 - Future aeronautical communications Y1 - 2011 SN - 978-953-307-625-6 SP - 317 EP - 332 PB - Intech CY - London ER - TY - CHAP A1 - Gkatzogias, Konstantinos A1 - Veljkoviv, Ana A1 - Pohoryles, Daniel A. A1 - Tsionis, Georgios A1 - Bournas, Dionysios A. A1 - Crowley, Helen A1 - Norlén, Hedvig A1 - Butenweg, Christoph A1 - Gervasio, Helena A1 - Manfredi, Vincenzo A1 - Masi, Angelo A1 - Zaharieva, Roumiana ED - Gkatzogias, Konstantinos ED - Tsionis, Georgios T1 - Policy practice and regional impact assessment for building renovation T2 - REEBUILD Integrated Techniques for the Seismic Strengthening & Energy Efficiency of Existing Buildings N2 - The work presented in this report provides scientific support to building renovation policies in the EU by promoting a holistic point of view on the topic. Integrated renovation can be seen as a nexus between European policies on disaster resilience, energy efficiency and circularity in the building sector. An overview of policy measures for the seismic and energy upgrading of buildings across EU Member States identified only a few available measures for combined upgrading. Regulatory framework, financial instruments and digital tools similar to those for energy renovation, together with awareness and training may promote integrated renovation. A framework for regional prioritisation of building renovation was put forward, considering seismic risk, energy efficiency, and socioeconomic vulnerability independently and in an integrated way. Results indicate that prioritisation of building renovation is a multidimensional problem. Depending on priorities, different integrated indicators should be used to inform policies and accomplish the highest relative or most spread impact across different sectors. The framework was further extended to assess the impact of renovation scenarios across the EU with a focus on priority regions. Integrated renovation can provide a risk-proofed, sustainable, and inclusive built environment, presenting an economic benefit in the order of magnitude of the highest benefit among the separate interventions. Furthermore, it presents the unique capability of reducing fatalities and energy consumption at the same time and, depending on the scenario, to a greater extent. Y1 - 2022 SN - 978-92-76-60454-9 U6 - http://dx.doi.org/10.2760/883122 SN - 1831-9424 SP - 1 EP - 68 PB - Publications Office of the European Union CY - Luxembourg ER - TY - CHAP A1 - Gitter, R. A1 - Hornhardt, Ch. A1 - Koewius, A. A1 - [u.a.], A1 - Wahle, Michael T1 - Konstruieren mit Aluminium [Kapitel 4] T2 - Aluminium-Taschenbuch / Hrsg.: Aluminium-Zentrale Düsseldorf. - Bd. 3: Weiterverarbeitung und Anwendung Y1 - 2003 SN - 3-87017-275-4 SP - 355 EP - 599 PB - Aluminium-Verlag CY - Düsseldorf ET - 16. Auflage ER - TY - CHAP A1 - Giresini, Linda A1 - Butenweg, Christoph T1 - Earthquake resistant design of structures according to Eurocode 8 T2 - Structural Dynamics with Applications in Earthquake and Wind Engineering N2 - The chapter initially provides a summary of the contents of Eurocode 8, its aim being to offer both to the students and to practising engineers an easy introduction into the calculation and dimensioning procedures of this earthquake code. Specifically, the general rules for earthquake-resistant structures, the definition of design response spectra taking behaviour and importance factors into account, the application of linear and non-linear calculation methods and the structural safety verifications at the serviceability and ultimate limit state are presented. The application of linear and non-linear calculation methods and corresponding seismic design rules is demonstrated on practical examples for reinforced concrete, steel and masonry buildings. Furthermore, the seismic assessment of existing buildings is discussed and illustrated on the example of a typical historical masonry building in Italy. The examples are worked out in detail and each step of the design process, from the preliminary analysis to the final design, is explained in detail. KW - Seismic design KW - Eurocode 8 KW - Design examples KW - Response spectrum KW - Pushover analysis Y1 - 2019 SN - 978-3-662-57550-5 (Online) SN - 978-3-662-57548-2 (Print) U6 - http://dx.doi.org/10.1007/978-3-662-57550-5_4 SP - 197 EP - 358 PB - Springer CY - Berlin ER - TY - CHAP A1 - Gidom, D. A1 - Pietsch, Wolfram T1 - Integrierte Steuerung von Bauprojekten durch Expertensysteme T2 - Dortmunder Expertensystemtage '91 : in Verbindung mit dem 3. Anwenderforum des KI-Verbundes NRW Y1 - 1991 SN - 3-88585-998-X SP - 356 EP - 365 PB - TÜV Rheinland CY - Köln ER - TY - CHAP A1 - Geisler, Simon A1 - Pieper, Martin T1 - Mathematik PLuS als E-Book. Kann ein E-Book zur Ingenieursmathematik alle Lerntypen ansprechen? T2 - Das elektronische Schulbuch 2016 Y1 - 2017 SN - 978-3-643-13475-2 SP - 99 EP - 111 PB - LIT Verlag CY - Berlin ER - TY - CHAP A1 - Gebhardt, Andreas A1 - Hoetter, Jan-Steffen T1 - Rapid Tooling T2 - CIRP Encyclopedia of Production Engineering Y1 - 2019 SN - 978-3-662-53120-4 U6 - http://dx.doi.org/10.1007/978-3-662-53120-4 SP - 39 EP - 52 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Gebhardt, Andreas T1 - Entwicklung der 3D-Drucktechnologie und Potenziale für die Anwendung im Mittelstand T2 - Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsfähigkeit steigert : Festschrift für Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.) Y1 - 2013 SN - 978-3-86359-136-6 SP - 55 EP - 59 PB - Apprimus Verlag CY - Aachen ER - TY - CHAP A1 - Funke, Harald A1 - Börner, Sebastian A1 - Hendrick, P. A1 - Recker, E. T1 - Modification and testing of an engine and fuel control system for a hydrogen fuelled gas turbine T2 - Progress in Propulsion Physics. Vol. 2 Y1 - 2011 SN - 978-2-7598-0673-7 SP - 475 EP - 486 PB - EDP Sciences CY - Les Ulis ER - TY - CHAP A1 - Frühwald, Katja A1 - Peterson, Leif Arne A1 - Hasenstab, Andreas ED - Fouad, Nabil A. T1 - Prüfverfahren zur Begutachtung der Materialeigenschaften von Holztragwerken T2 - Bauphysik‐Kalender 2012: Schwerpunkt: Gebäudediagnostik N2 - Dieses Kapitel beinhaltet: - Einleitung - Ausgewählte typische Schäden an Holzbauwerken - Das Material Holz und seine Besonderheiten - Bestandserfassung - Labormethoden - Begutachtungsbeispiele - Zusammenfassung und Schlussfolgerungen - Literatur Y1 - 2012 SN - 9783433029862 (Print) SN - 9783433601235 (Online) U6 - http://dx.doi.org/10.1002/9783433601235.ch4 SP - 103 EP - 155 PB - Ernst & Sohn CY - Berlin ER - TY - CHAP A1 - Frotscher, Ralf A1 - Staat, Manfred ED - Artmann, Gerhard ED - Temiz Artmann, Aysegül ED - Zhubanova, Azhar A. ED - Digel, Ilya T1 - Towards Patient-Specific Computational Modeling of hiPS-Derived Cardiomyocyte Function and Drug Action T2 - Biological, Physical and Technical Basics of Cell Engineering N2 - Human-induced pluripotent stem cell-derived cardiomyocytes (hiPS-CM) today are widely used for the investigation of normal electromechanical cardiac function, of cardiac medication and of mutations. Computational models are thus established that simulate the behavior of this kind of cells. This section first motivates the modeling of hiPS-CM and then presents and discusses several modeling approaches of microscopic and macroscopic constituents of human-induced pluripotent stem cell-derived and mature human cardiac tissue. The focus is led on the mapping of the computational results one can achieve with these models onto mature human cardiomyocyte models, the latter being the real matter of interest. Model adaptivity is the key feature that is discussed because it opens the way for modeling various biological effects like biological variability, medication, mutation and phenotypical expression. We compare the computational with experimental results with respect to normal cardiac function and with respect to inotropic and chronotropic drug effects. The section closes with a discussion on the status quo of the specificity of computational models and on what challenges have to be solved to reach patient-specificity. Y1 - 2018 SN - 978-981-10-7904-7 U6 - http://dx.doi.org/10.1007/978-981-10-7904-7_10 SP - 233 EP - 250 PB - Springer CY - Singapore ER - TY - CHAP A1 - Frotscher, Ralf A1 - Goßmann, Matthias A1 - Raatschen, Hans-Jürgen A1 - Temiz Artmann, Aysegül A1 - Staat, Manfred T1 - Simulation of cardiac cell-seeded membranes using the edge-based smoothed FEM T2 - Shell and membrane theories in mechanics and biology. (Advanced structured materials ; 45) N2 - We present an electromechanically coupled Finite Element model for cardiac tissue. It bases on the mechanical model for cardiac tissue of Hunter et al. that we couple to the McAllister-Noble-Tsien electrophysiological model of purkinje fibre cells. The corresponding system of ordinary differential equations is implemented on the level of the constitutive equations in a geometrically and physically nonlinear version of the so-called edge-based smoothed FEM for plates. Mechanical material parameters are determined from our own pressure-deflection experimental setup. The main purpose of the model is to further examine the experimental results not only on mechanical but also on electrophysiological level down to ion channel gates. Moreover, we present first drug treatment simulations and validate the model with respect to the experiments. Y1 - 2015 SN - 978-3-319-02534-6 ; 978-3-319-02535-3 SP - 187 EP - 212 PB - Springer CY - Heidelberg ER - TY - CHAP A1 - Freyer, Nils A1 - Kempt, Hendrik ED - Bhakuni, Himani ED - Miotto, Lucas T1 - AI-DSS in healthcare and their power over health-insecure collectives T2 - Justice in global health N2 - AI-based systems are nearing ubiquity not only in everyday low-stakes activities but also in medical procedures. To protect patients and physicians alike, explainability requirements have been proposed for the operation of AI-based decision support systems (AI-DSS), which adds hurdles to the productive use of AI in clinical contexts. This raises two questions: Who decides these requirements? And how should access to AI-DSS be provided to communities that reject these standards (particularly when such communities are expert-scarce)? This chapter investigates a dilemma that emerges from the implementation of global AI governance. While rejecting global AI governance limits the ability to help communities in need, global AI governance risks undermining and subjecting health-insecure communities to the force of the neo-colonial world order. For this, this chapter first surveys the current landscape of AI governance and introduces the approach of relational egalitarianism as key to (global health) justice. To discuss the two horns of the referred dilemma, the core power imbalances faced by health-insecure collectives (HICs) are examined. The chapter argues that only strong demands of a dual strategy towards health-secure collectives can both remedy the immediate needs of HICs and enable them to become healthcare independent. Y1 - 2023 SN - 9781003399933 U6 - http://dx.doi.org/10.4324/9781003399933-4 SP - 38 EP - 55 PB - Routledge CY - London ER - TY - CHAP A1 - Frewer, Hans A1 - Meliß, Michael T1 - Stromerzeugung - Perspektiven der Kraftwerkstechnik T2 - Die Zukunft der Stromversorgung / Alfred Voß (Hrsg.) Y1 - 1992 SN - 3-8022-0299-6 SP - 49 EP - 117 PB - Verlags- und Wirtschaftsgesellschaft der Elektrizitätswerke CY - Frankfurt a. M. ER - TY - CHAP A1 - Franzen, Julian A1 - Stecken, Jannis A1 - Pfaff, Raphael A1 - Kuhlenkötter, Bernd T1 - Using the Digital Shadow for a Prescriptive Optimization of Maintenance and Operation : The Locomotive in the Context of the Cyber-Physical System T2 - Advances in Production, Logistics and Traffic N2 - In competition with other modes of transport, rail freight transport is looking for solutions to become more attractive. Short-term success can be achieved through the data-driven optimization of operations and maintenance as well as the application of novel strategies such as prescriptive maintenance. After introducing the concept of prescriptive maintenance, this paper aims to prove that vehicle-focused applications of this approach indeed have the potential to increase attractiveness. However, even greater advantages can be activated if data from the horizontal network of the vehicle is available. Drawing on the state of the art in research and technology in the field of cyber-physical systems (CPS) as well as digital twins and shadows, our work serves to design a system of systems for the horizontal interconnection of a rail vehicle and to conceptualize a draft for a digital twin of a locomotive. Y1 - 2019 SN - 978-3-030-13535-5 U6 - http://dx.doi.org/10.1007/978-3-030-13535-5_19 SP - 265 EP - 276 PB - Springer CY - Cham ER - TY - CHAP A1 - Fissabre, Anke A1 - Wilson, Ariane ED - Feiglstorfer, Hubert T1 - "Lehmbaupropaganda" : On the tradition of earth building literature T2 - Earth Construction and Tradition. Vol. I Y1 - 2016 SN - 978-3-900265-34-2 SP - 47 EP - 69 PB - IVA Institut für vergleichende Architekturforschung CY - Wien ER - TY - CHAP A1 - Fissabre, Anke A1 - Wilson, Ariane ED - Di Teodoro, Francesco P. ED - Ferretti, Emanuela ED - Frommel, Sabine ED - Schlimme, Hermann T1 - Hypotheses on the Tower of Monthoiron: A Built Design of Italian and Leonardian Inspiration in France T2 - Leonardo da Vinci: l’architettura / Léonard de Vinci : l’architecture Y1 - 2022 SN - 979-12-80956-00-2 N1 - Sprachen laut Verlagsangaben: Italienisch, Englisch, Französisch SP - 287 EP - 300 PB - Campisano Editore CY - Roma ER - TY - CHAP A1 - Fissabre, Anke A1 - Niethammer, Bernd ED - Graf, Franz T1 - Early Glazed Curtain Walls and their Preservation T2 - Il vetro nell’architettura del XX secolo : conservazione e restauro = Glass in the 20th Century Architecture : Preservation and Restoration Y1 - 2011 SN - 9788887624502 SP - 185 EP - 199 PB - Mendrisio Academy Press CY - Mendrisio ER - TY - CHAP A1 - Fissabre, Anke ED - Priesterjahn, Maike T1 - Vom Schiff an Land oder von der Muschel zur Rocaille T2 - Schwimmender Barock : Das Schiff als Repräsentationsobjekt Y1 - 2018 SN - 978-3-89809-153-4 SP - 59 EP - 65 PB - Bebra Verlag CY - Berlin ER - TY - CHAP A1 - Fissabre, Anke ED - Dux, Holger A. T1 - Die Bauten des jüdischen Friedhofs an der Lütticher Straße T2 - Der Jüdische Friedhof Aachen Y1 - 2022 SN - 978-3-87519-266-7 SP - 51 EP - 69 PB - Mayersche Buchhandlung Aachen GmbH CY - Aachen ER - TY - CHAP A1 - Fissabre, Anke ED - Dux, Holger A. T1 - Ein Entwurf für die Umnutzung der Bauten des jüdischen Friedhofs an der Lütticher Straße T2 - Der jüdische Friedhof Aachen Lütticher Straße Aachen Y1 - 2022 SN - 978-3-87519-266-7 SP - 71 EP - 74 PB - Mayersche Buchhandlung Aachen GmbH CY - Aachen ER - TY - CHAP A1 - Fissabre, Anke ED - Soldwisch, Ines ED - Schmitz, Stefan T1 - kirchen-bauhaus? – Die Kunstgewerbeschule in Aachen unter Rudolf Schwarz T2 - Zwischen den Zeiten - Besatzung und Aufbruch in Aachen, 1919-1932 Y1 - 2022 SN - 978-3-9825016-0-4 N1 - Zeitreisen Sammlung Crous, Schriftenreihe 15. SP - 54 EP - 65 PB - Aachener Karnevalsverein (AKV) CY - Aachen ER - TY - CHAP A1 - Finkenberger, Isabel Maria A1 - Herbert, Saskia A1 - Malorny, Thomas A1 - Koch, Christian T1 - Perforierte Wirklichkeit und mögliche Zukünfte : ein Gespräch T1 - Perforated reality and possible futures : a conversation T2 - Komplement und Verstärker : zum Verhältnis von Stadtplanung, künstlerischen Praktiken und Kulturinstitutionen Y1 - 2019 SN - 978-3-86859-578-9 SP - 108 EP - 129 PB - JOVIS Verlag CY - Berlin ER - TY - CHAP A1 - Finkenberger, Isabel Maria A1 - Baumeister, Eva-Maria A1 - Koch, Christian T1 - Komplement und Verstärker : Wandel durch neue Allianzen T1 - Amplifier and complement : creating change through new alliances T2 - Komplement und Verstärker : zum Verhältnis von Stadtplanung, künstlerischen Praktiken und Kulturinstitutionen Y1 - 2019 SN - 978-3-86859-578-9 SP - 10 EP - 39 PB - JOVIS Verlag CY - Berlin ER - TY - CHAP A1 - Finkenberger, Isabel Maria A1 - Baumeister, Eva-Maria A1 - Koch, Christian T1 - Komplement und Verstärker : der Diskurs geht weiter T1 - Amplifier and complement : the discourse continues T2 - Komplement und Verstärker : zum Verhältnis von Stadtplanung, künstlerischen Praktiken und Kulturinstitutionen Y1 - 2019 SN - 978-3-86859-578-9 SP - 40 EP - 49 PB - JOVIS Verlag CY - Berlin ER - TY - CHAP A1 - Finkenberger, Isabel Maria A1 - Baumeister, Eva-Maria A1 - Koch, Christian T1 - Themen T1 - Topics T2 - Komplement und Verstärker: zum Verhältnis von Stadtplanung, künstlerischen Praktiken und Kulturinstitutionen Y1 - 2019 SN - 978-3-86859-578-9 SP - 50 EP - 57 PB - JOVIS Verlag CY - Berlin ER - TY - CHAP A1 - Finkenberger, Isabel Maria A1 - Baumeister, Eva-Maria ED - Berger, Hilke Marit ED - Ziemer, Gesa T1 - Working in between : Die Stadt von der anderen Seite sehen : Where Urban Planning Meets Artistic Practice T2 - New Stakeholders of Urban Change : A Question of Culture and Attitude?. - (Perspectives in Metropolitan Research ; IV) Y1 - 2017 SN - 978-3-86859-487-4 SP - 119 EP - 129 PB - JOVIS Verlag CY - Berlin ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Buchert, Margitta T1 - Schwellenreiten T1 - Riding the threshold T2 - Prozesse reflexiven Entwerfens : Entwerfen und Forschen in Architektur und Landschaft Y1 - 2018 SN - 978-3-86859-558-1 SP - 208 EP - 226 PB - JOVIS Verlag CY - Berlin ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Bredenbeck, Martin T1 - Vox populi. (Transformations-)potenziale nachkriegsmoderner Freiraumressourcen T2 - Grün modern - Gärten und Parks der 1950er bis 1970er Jahre Y1 - 2024 SN - 9783925374357 N1 - Ein Kulturerbe als Herausforderung für Denkmalpflege und Vermittlungsarbeit ; Dokumentation der Tagung am 15. und 16. Oktober 2013 in Hamburg SP - 31 EP - 38 PB - BHU CY - Bonn ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Büscher, Barbara ED - Krasny, Elke ED - Ortmann, Lucie T1 - Transformatives Handeln als disziplinüberschreitende, kollektive Aktion. Stadtentwicklung trifft künstlerische und kollaborative Handlungspraxen T2 - Porös-Werden : geteilte Räume, urbane Dramaturgien, performatives Kuratieren Y1 - 2024 SN - 978-3-98514-543-0 SP - 144 EP - 158 PB - Turia + Kant CY - Wien ER - TY - CHAP A1 - Finkenberger, Isabel Maria T1 - Die Stadt als städtisch-theatrale Versuchsanordnung: Wie wollen wir in Zukunft leben und welche Stadt brauchen wir dafür? T2 - Un/Certain Futures - Rollen des Designs in gesellschaftlichen Transformationsprozessen Y1 - 2024 SN - 9783839443323 U6 - http://dx.doi.org/https://doi.org/10.1515/9783839443323-009 SP - 86 EP - 95 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Pufke, Andrea T1 - Räumliche Transformation als Planungsaufgabe T2 - Zurück in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier Y1 - 2024 N1 - Mitteilungen aus dem LVR-Amt für Denkmalpflege im Rheinland 39 : Zurück in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier. Dokumentation zum 7. Rheinischen Tag für Denkmalpflege in Morschenich, 2. Juni 2022 SP - 70 EP - 77 PB - LVR-Amt für Denkmalpflege im Rheinland CY - Pulheim ER - TY - CHAP A1 - Fiedler, Gerda A1 - Henn, Gudrun A1 - Melcher, Karin ED - Morschheuser, Petra T1 - ANPAK - Ein Anpassungskurs für Studienanfänger in den Ingenieurwissenschaften T2 - Qualifizierung von Studierenden im Student-Life-Cycle. Tagungsband zum Mosbacher Tag der Lehre am 23.10.2014 / Y1 - 2015 SN - 978-3-943656-02-2 SP - 90 EP - 93 PB - Duale Hochschule Baden-Württemberg (DHBW) CY - Mosbach ER - TY - CHAP A1 - Ferger, Martin ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Arbeitsvorbereitung und Ablaufplanung T2 - Zahlentafeln für den Baubetrieb N2 - Die Arbeitsvorbereitung, als ein wesentliches Aufgabengebiet des Baubetriebswesens, ist von enormer Bedeutung für den Erfolg eines Bauprojektes. Die Arbeitsvorbereitung lässt sich zeitlich sowohl in der Angebotsphase (kalkulationsbegleitende Arbeitsvorbereitung), in der Vorbereitungsphase der Baustelle (von Auftragsvergabe bis Baubeginn) als auch baubegleitend einordnen. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - http://dx.doi.org/10.1007/978-3-658-41330-9_6 SP - 299 EP - 332 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Feldmann, M. A1 - Döring, Bernd A1 - Pyschny, D. T1 - Floor systems; Sustainabilty analyses and assessments of steel bridges T2 - Sustainable steel buildings : a practical guide for structures and envelopes Y1 - 2016 SN - 978-1-118-74079-8 (PDF) SN - 978-1-118-74111-5 SP - 198 EP - 223 PB - Wiley Blackwell CY - Chichester, West Sussex ER - TY - CHAP A1 - Feiser, Johannes ED - Vismann, Ulrich T1 - Geotechnik T2 - Wendehorst Bautechnische Zahlentafeln N2 - In der nationalen und der europäischen Normung werden die geotechnischen Aufgaben zwecks Mindestanforderungen an Baugrunduntersuchung, rechnerische Nachweise und Überwachung der Ausführung in drei Klassen (Kategorien) eingeteilt. Sie richten sich nach der zu erwartenden Reaktion des Baugrundes, nach dem geotechnischen Schwierigkeitsgrad des Tragwerks und seiner Einflüsse auf dieUmgebung. Y1 - 2012 SN - 978-3-8348-0960-5 U6 - http://dx.doi.org/10.1007/978-3-8348-8613-2_17 N1 - Kapitel 17 SP - 1221 EP - 1332 PB - Vieweg + Teubner CY - Wiesbaden ET - 34 ER - TY - CHAP A1 - Feiser, Johannes T1 - Geotechnik T2 - Wendehorst Beispiele aus der Baupraxis. - 4. Aufl. Y1 - 2012 SN - 978-3-8348-0999-5 ; 978-3-8348-8229-5 U6 - http://dx.doi.org/10.1007/978-3-8348-8229-5_14 SP - 453 EP - 495 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Feiser, Johannes T1 - Geotechnik T2 - Wendehorst Beispiele aus der Baupraxis. - 3. Aufl. Y1 - 2009 SN - 978-3-8348-0684-0 ; 978-3-8348-9997-2 U6 - http://dx.doi.org/10.1007/978-3-8348-9997-2_13 SP - 351 EP - 392 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Feiser, Johannes T1 - Geotechnik T2 - Wendehorst Beispiele aus der Baupraxis. - 1. Aufl. Y1 - 2005 SN - 3-519-00489-5 ; 978-3-519-00489-9 SP - 195 EP - 220 PB - Teubner CY - Stuttgart ER - TY - CHAP A1 - Feiser, Johannes ED - Vismann, Ulrich T1 - Geotechnik T2 - Wendehorst Bautechnische Zahlentafeln / 35. Auflage N2 - In der nationalen und der europäischen Normung werden die geotechnischen Aufgaben zwecks Mindestanforderungen an Baugrunduntersuchung, rechnerische Nachweise und Überwachung der Ausführung in drei Klassen (Kategorien) eingeteilt. Sie richten sich nach der zu erwartenden Reaktion des Baugrundes, nach dem geotechnischen Schwierigkeitsgrad des Tragwerks und seiner Einflüsse auf die Umgebung. In DIN 4020 wurde die Einteilung bezüglich Art und Umfang der geotechnischen Untersuchungen bereits verbindlich eingeführt. Y1 - 2015 SN - 978-3-658-01688-3 (Print) SN - 978-3-658-01689-0 (Online) U6 - http://dx.doi.org/10.1007/978-3-658-01689-0_17 SP - 1019 EP - 1101 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Feiser, Johannes T1 - Geotechnik T2 - Wendehorst Beispiele aus der Baupraxis. / 5. Auflage Y1 - 2015 SN - 978-3-658-01689-0 ; 978-3-410-24199-7 U6 - http://dx.doi.org/10.1007/978-3-658-01681-4_14 SP - 547 EP - 598 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Introduction to Additive Manufacturing T2 - 3D Printing of Optical Components N2 - Additive manufacturing (AM) works by creating objects layer by layer in a manner similar to a 2D printer with the “printed” layers stacked on top of each other. The layer-wise manufacturing nature of AM enables fabrication of freeform geometries which cannot be fabricated using conventional manufacturing methods as a one part. Depending on how each layer is created and bonded to the adjacent layers, different AM methods have been developed. In this chapter, the basic terms, common materials, and different methods of AM are described, and their potential applications are discussed. KW - Additive manufacturing KW - 3D printing KW - Digital manufacturing KW - Rapid prototyping KW - Rapid manufacturing Y1 - 2020 SN - 978-3-030-58960-8 U6 - http://dx.doi.org/10.1007/978-3-030-58960-8_1 SP - 1 EP - 22 PB - Springer CY - Cham ER - TY - CHAP A1 - Fabo, Sabine A1 - Eisenbeis, Manfred ED - Weber, Hermann T1 - Medienkultur : die mediale Konstruktion von Wirklichkeit T2 - Globalisierung der Zivilisation und überlieferte Kulturen : 28. - 30. April 1995 Y1 - 1995 SN - 3-926288-10-8 N1 - Jahresakademie / Katholischer Akademischer Ausländer-Dienst, KAAD ; [9] PB - Katholischer Akademischer Ausländer-Dienst CY - Bonn ER - TY - CHAP A1 - Fabo, Sabine ED - Brüstle, Christa T1 - Musik und Interaktivität : Modelle eines emanzipierten Handelns? T2 - Musik | Politik : Musik im Dialog (Jahrbuch der Berliner Gesellschaft für Neue Musik ; 5) Y1 - 2004 SN - 3-89727-257-1 VL - 2002 PB - Pfau Verlag CY - Saarbrücken ER - TY - CHAP A1 - Fabo, Sabine ED - Eming, Jutta T1 - Intermedia light : zur Erfüllung synästhetischer Phantasien in Echtzeit T2 - Mediale Performanzen : historische Konzepte und Perspektiven (Rombach Wissenschaften : Reihe Litterae ; 97) Y1 - 2002 SN - 3-7930-9344-1 SP - 197 EP - 220 PB - Rombach Verlag CY - Freiburg im Breisgau ER -