TY - CHAP A1 - Finkenberger, Isabel Maria ED - Pufke, Andrea T1 - Räumliche Transformation als Planungsaufgabe T2 - Zurück in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier Y1 - 2024 N1 - Mitteilungen aus dem LVR-Amt für Denkmalpflege im Rheinland 39 : Zurück in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier. Dokumentation zum 7. Rheinischen Tag für Denkmalpflege in Morschenich, 2. Juni 2022 SP - 70 EP - 77 PB - LVR-Amt für Denkmalpflege im Rheinland CY - Pulheim ER - TY - CHAP A1 - Langohr, Philipp A1 - Bung, Daniel Bernhard A1 - Crookston, Brian M. ED - Ortega-Sánchez, Miguel T1 - Hybrid investigation of labyrinth weirs: Discharge capacity and energy dissipation T2 - Proceedings of the 39th IAHR World Congress N2 - The replacement of existing spillway crests or gates with labyrinth weirs is a proven techno-economical means to increase the discharge capacity when rehabilitating existing structures. However, additional information is needed regarding energy dissipation of such weirs, since due to the folded weir crest, a three-dimensional flow field is generated, yielding more complex overflow and energy dissipation processes. In this study, CFD simulations of labyrinth weirs were conducted 1) to analyze the discharge coefficients for different discharges to compare the Cd values to literature data and 2) to analyze and improve energy dissipation downstream of the structure. All tests were performed for a structure at laboratory scale with a height of approx. P = 30.5 cm, a ratio of the total crest length to the total width of 4.7, a sidewall angle of 10° and a quarter-round weir crest shape. Tested headwater ratios were 0.089 ≤ HT/P ≤ 0.817. For numerical simulations, FLOW-3D Hydro was employed, solving the RANS equations with use of finite-volume method and RNG k-ε turbulence closure. In terms of discharge capacity, results were compared to data from physical model tests performed at the Utah Water Research Laboratory (Utah State University), emphasizing higher discharge coefficients from CFD than from the physical model. For upstream heads, some discrepancy in the range of ± 1 cm between literature, CFD and physical model tests was identified with a discussion regarding differences included in the manuscript. For downstream energy dissipation, variable tailwater depths were considered to analyze the formation and sweep-out of a hydraulic jump. It was found that even for high discharges, relatively low downstream Froude numbers were obtained due to high energy dissipation involved by the three-dimensional flow between the sidewalls. The effects of some additional energy dissipation devices, e.g. baffle blocks or end sills, were also analyzed. End sills were found to be non-effective. However, baffle blocks with different locations may improve energy dissipation downstream of labyrinth weirs. Y1 - 2022 SN - 978-90-832612-1-8 U6 - https://doi.org/10.3850/IAHR-39WC252171192022738 SN - 2521-7119 (print) SN - 2521-716X (online) N1 - 39th IAHR World Congress, 19. - 24. Juni 2022, Granada SP - 2313 EP - 2318 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - CHAP A1 - Crookston, Brian M. A1 - Bung, Daniel Bernhard ED - Ortega-Sánchez, Miguel T1 - Application of RGB-D cameras in hydraulic laboratory studies T2 - Proceedings of the 39th IAHR World Congress N2 - Non-intrusive measuring techniques have attained a lot of interest in relation to both hydraulic modeling and prototype applications. Complimenting acoustic techniques, significant progress has been made for the development of new optical methods. Computer vision techniques can help to extract new information, e. g. high-resolution velocity and depth data, from videos captured with relatively inexpensive, consumer-grade cameras. Depth cameras are sensors providing information on the distance between the camera and observed features. Currently, sensors with different working principles are available. Stereoscopic systems reference physical image features (passive system) from two perspectives; in order to enhance the number of features and improve the results, a sensor may also estimate the disparity from a detected light to its original projection (active stereo system). In the current study, the RGB-D camera Intel RealSense D435, working on such stereo vision principle, is used in different, typical hydraulic modeling applications. All tests have been conducted at the Utah Water Research Laboratory. This paper will demonstrate the performance and limitations of the RGB-D sensor, installed as a single camera and as camera arrays, applied to 1) detect the free surface for highly turbulent, aerated hydraulic jumps, for free-falling jets and for an energy dissipation basin downstream of a labyrinth weir and 2) to monitor local scours upstream and downstream of a Piano Key Weir. It is intended to share the authors’ experiences with respect to camera settings, calibration, lightning conditions and other requirements in order to promote this useful, easily accessible device. Results will be compared to data from classical instrumentation and the literature. It will be shown that even in difficult application, e. g. the detection of a highly turbulent, fluctuating free-surface, the RGB-D sensor may yield similar accuracy as classical, intrusive probes. Y1 - 2022 SN - 978-90-832612-1-8 U6 - https://doi.org/10.3850/IAHR-39WC252171192022964 SN - 2521-7119 (print) SN - 2521-716X (online) N1 - 39th IAHR World Congress, 19. - 24. Juni 2022, Granada SP - 5127 EP - 5133 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - CHAP A1 - Tran, Ngoc Trinh A1 - Trinh, Tu Luc A1 - Dao, Ngoc Tien A1 - Giap, Van Tan A1 - Truong, Manh Khuyen A1 - Dinh, Thuy Ha A1 - Staat, Manfred T1 - Limit and shakedown analysis of structures under random strength T2 - Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training N2 - Direct methods comprising limit and shakedown analysis is a branch of computational mechanics. It plays a significant role in mechanical and civil engineering design. The concept of direct method aims to determinate the ultimate load bearing capacity of structures beyond the elastic range. For practical problems, the direct methods lead to nonlinear convex optimization problems with a large number of variables and onstraints. If strength and loading are random quantities, the problem of shakedown analysis is considered as stochastic programming. This paper presents a method so called chance constrained programming, an effective method of stochastic programming, to solve shakedown analysis problem under random condition of strength. In this our investigation, the loading is deterministic, the strength is distributed as normal or lognormal variables. KW - Reliability of structures KW - Stochastic programming KW - Chance constrained programming KW - Shakedown analysis KW - Limit analysis Y1 - 2022 SN - 978-604-357-084-7 N1 - 11th National Conference on Mechanics (NACOME 2022), December 2-3, 2022, VNU University of Engineering and Technology, Hanoi, Vietnam SP - 510 EP - 518 PB - Nha xuat ban Khoa hoc tu nhien va Cong nghe (Verlag Naturwissenschaft und Technik) CY - Hanoi ER - TY - GEN A1 - Keimer, Jona A1 - Girbig, Leo A1 - Mayntz, Joscha A1 - Tegtmeyer, Philipp A1 - Wendland, Frederik A1 - Dahman, Peter A1 - Fisher, Alex A1 - Dorrington, Graham T1 - Flight mission optimization for eco-efficiency in consideration of electric regeneration and atmospheric conditions T2 - AIAA AVIATION 2022 Forum N2 - The development and operation of hybrid or purely electrically powered aircraft in regional air mobility is a significant challenge for the entire aviation sector. This technology is expected to lead to substantial advances in flight performance, energy efficiency, reliability, safety, noise reduction, and exhaust emissions. Nevertheless, any consumed energy results in heat or carbon dioxide emissions and limited electric energy storage capabilities suppress commercial use. Therefore, the significant challenges to achieving eco-efficient aviation are increased aircraft efficiency, the development of new energy storage technologies, and the optimization of flight operations. Two major approaches for higher eco-efficiency are identified: The first one, is to take horizontal and vertical atmospheric motion phenomena into account. Where, in particular, atmospheric waves hold exciting potential. The second one is the use of the regeneration ability of electric aircraft. The fusion of both strategies is expected to improve efficiency. The objective is to reduce energy consumption during flight while not neglecting commercial usability and convenient flight characteristics. Therefore, an optimized control problem based on a general aviation class aircraft has to be developed and validated by flight experiments. The formulated approach enables a development of detailed knowledge of the potential and limitations of optimizing flight missions, considering the capability of regeneration and atmospheric influences to increase efficiency and range. Y1 - 2022 U6 - https://doi.org/10.2514/6.2022-4118 N1 - AIAA AVIATION 2022 Forum, June 27-July 1, 2022 Chicago, IL & Virtual PB - AIAA CY - Reston, Va. ER - TY - JOUR A1 - Akimbekov, Nuraly S. A1 - Digel, Ilya A1 - Tastambek, Kuanysh T. A1 - Marat, Adel K. A1 - Turaliyeva, Moldir A. A1 - Kaiyrmanova, Gulzhan K. T1 - Biotechnology of Microorganisms from Coal Environments: From Environmental Remediation to Energy Production JF - Biology N2 - It was generally believed that coal sources are not favorable as live-in habitats for microorganisms due to their recalcitrant chemical nature and negligible decomposition. However, accumulating evidence has revealed the presence of diverse microbial groups in coal environments and their significant metabolic role in coal biogeochemical dynamics and ecosystem functioning. The high oxygen content, organic fractions, and lignin-like structures of lower-rank coals may provide effective means for microbial attack, still representing a greatly unexplored frontier in microbiology. Coal degradation/conversion technology by native bacterial and fungal species has great potential in agricultural development, chemical industry production, and environmental rehabilitation. Furthermore, native microalgal species can offer a sustainable energy source and an excellent bioremediation strategy applicable to coal spill/seam waters. Additionally, the measures of the fate of the microbial community would serve as an indicator of restoration progress on post-coal-mining sites. This review puts forward a comprehensive vision of coal biodegradation and bioprocessing by microorganisms native to coal environments for determining their biotechnological potential and possible applications. Y1 - 2022 U6 - https://doi.org/10.3390/biology11091306 SN - 2079-7737 N1 - This article belongs to the Special Issue "Microbial Ecology and Evolution in Extreme Environments" VL - 11 IS - 9 PB - MDPI CY - Basel ER - TY - GEN A1 - Krafft, Simone A1 - Kuka, Katrin A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Utilization of Lolium perenne varieties as a renewable substrate for single-cell proteins, lactate, and composite materials T2 - Chemie Ingenieur Technik N2 - Lolium perenne (perennial ryegrass) is aproductive and high-quality forage grass indigenous to Southern Europe, temperate Asia, and North Africa. Nowadays it is widespread and the dominant grass species on green areas in temperate climates. This abundant source of biomass is suitable for the development of bioeconomic processes because of its high cellulose and water-soluble carbohydrate content. In this work, novel breeds of the perennial ryegrass are being examined with regards to their quality parameters and biotechnological utilization options within the context of bioeconomy. Three processing operations are presented. In the first process, the perennial ryegrass is pretreated by pressing or hydrothermal extraction to derive glucosevia subsequent enzymatic hydrolysis of cellulose. A yield of up to 82 % glucose was achieved when using the hydrothermal ex-traction as pretreatment. In a second process, the ryegrass is used to produce lactic acid in high concentrations. The influence of the growth conditions and the cutting time on the carboxylic acid yield is investigated. A yield of lactic acid of above 150 g kg⁻¹ dry matter was achieved. The third process is to use Lolium perenne as a substrate in the fermentation of K. marxianus for the microbial production of single-cell proteins. The perennial ryegrass is screw-pressed and the press juice is used as medium. When supplementing the press juice with yeast media components, a biomass concentration of up to 16 g L⁻¹ could be achieved. Y1 - 2022 U6 - https://doi.org/10.1002/cite.202255306 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet and DECHEMA‐BioTechNet Jahrestagungen 2022 together with 13th ESBES Symposium 2022, 12. - 15. September 2022, Eurogress Aachen VL - 94 IS - 9 SP - 1303 EP - 1304 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Topcu, Murat A1 - Madabhushi, Gopal Santana Phani A1 - Staat, Manfred T1 - Datasets from FEM Simulations done with COMSOL Multiphysics and Code_Aster N2 - Datasets from FEM Simulations done with COMSOL Multiphysics and Code_Aster for an elastic stress transfer between matrix and fibres having a variable radius. KW - Natural fibres KW - Polymer-matrix composites KW - Biocomposites KW - Stress concentrations KW - Finite element analysis (FEA) Y1 - 2022 U6 - https://doi.org/10.6084/m9.figshare.19333295.v2 ER - TY - JOUR A1 - Thiebes, Anja Lena A1 - Klein, Sarah A1 - Zingsheim, Jonas A1 - Möller, Georg H. A1 - Gürzing, Stefanie A1 - Reddemann, Manuel A. A1 - Behbahani, Mehdi A1 - Cornelissen, Christian G. T1 - Effervescent atomizer as novel cell spray technology to decrease the gas-to-liquid ratio JF - pharmaceutics N2 - Cell spraying has become a feasible application method for cell therapy and tissue engineering approaches. Different devices have been used with varying success. Often, twin-fluid atomizers are used, which require a high gas velocity for optimal aerosolization characteristics. To decrease the amount and velocity of required air, a custom-made atomizer was designed based on the effervescent principle. Different designs were evaluated regarding spray characteristics and their influence on human adipose-derived mesenchymal stromal cells. The arithmetic mean diameters of the droplets were 15.4–33.5 µm with decreasing diameters for increasing gas-to-liquid ratios. The survival rate was >90% of the control for the lowest gas-to-liquid ratio. For higher ratios, cell survival decreased to approximately 50%. Further experiments were performed with the design, which had shown the highest survival rates. After seven days, no significant differences in metabolic activity were observed. The apoptosis rates were not influenced by aerosolization, while high gas-to-liquid ratios caused increased necrosis levels. Tri-lineage differentiation potential into adipocytes, chondrocytes, and osteoblasts was not negatively influenced by aerosolization. Thus, the effervescent aerosolization principle was proven suitable for cell applications requiring reduced amounts of supplied air. This is the first time an effervescent atomizer was used for cell processing. KW - tri-lineage differentiation KW - survival KW - twin-fluid atomizer KW - adipose-derived stromal cells (ASCs) KW - cell atomization KW - cell aerosolization Y1 - 2022 U6 - https://doi.org/10.3390/pharmaceutics14112421 N1 - This article belongs to the Special Issue "Stromal, Stem, Signaling Cells: The Multiple Roles and Applications of Mesenchymal Cells" VL - 14 IS - 11 PB - MDPI CY - Basel ER - TY - CHAP A1 - Veettil, Yadu Krishna Morassery A1 - Rakshit, Shantam A1 - Schopen, Oliver A1 - Kemper, Hans A1 - Esch, Thomas A1 - Shabani, Bahman ED - Bin Abdollah, Mohd Fadzli ED - Amiruddin, Hilmi ED - Singh, Amrik Singh Phuman ED - Munir, Fudhail Abdul ED - Ibrahim, Asriana T1 - Automated Control System Strategies to Ensure Safety of PEM Fuel Cells Using Kalman Filters T2 - Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia N2 - Having well-defined control strategies for fuel cells, that can efficiently detect errors and take corrective action is critically important for safety in all applications, and especially so in aviation. The algorithms not only ensure operator safety by monitoring the fuel cell and connected components, but also contribute to extending the health of the fuel cell, its durability and safe operation over its lifetime. While sensors are used to provide peripheral data surrounding the fuel cell, the internal states of the fuel cell cannot be directly measured. To overcome this restriction, Kalman Filter has been implemented as an internal state observer. Other safety conditions are evaluated using real-time data from every connected sensor and corrective actions automatically take place to ensure safety. The algorithms discussed in this paper have been validated thorough Model-in-the-Loop (MiL) tests as well as practical validation at a dedicated test bench. KW - control system KW - PEM fuel cells KW - Kalman filter Y1 - 2022 SN - 978-981-19-3178-9 SN - 978-981-19-3179-6 (E-Book) U6 - https://doi.org/10.1007/978-981-19-3179-6_55 SN - 2195-4356 N1 - 7th International Conference and Exhibition on Sustainable Energy and Advanced Material (ICE-SEAM 2021), Universiti Teknikal Malaysia Melaka (UTeM), Malaysia, in association with the Universitas Sebelas Maret (UNS), Indonesia, 23 November 2021 SP - 296 EP - 299 PB - Springer Nature CY - Singapore ER - TY - BOOK A1 - Laack, Walter van T1 - Greater Than the Entire Universe Y1 - 2022 SN - 978-3-936624-52-6 PB - van Laack GmbH CY - Aachen ER - TY - CHAP A1 - Tamaldin, Noreffendy A1 - Mansor, Muhd Rizuan A1 - Mat Yamin, Ahmad Kamal A1 - Bin Abdollah, Mohd Fazli A1 - Esch, Thomas A1 - Tonoli, Andrea A1 - Reisinger, Karl Heinz A1 - Sprenger, Hanna A1 - Razuli, Hisham ED - Bin Abdollah, Mohd Fadzli ED - Amiruddin, Hilmi ED - Singh, Amrik Singh Phuman ED - Munir, Fudhail Abdul ED - Ibrahim, Asriana T1 - Development of UTeM United Future Fuel Design Training Center Under Erasmus+ United Program T2 - Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia N2 - The industrial revolution IR4.0 era have driven many states of the art technologies to be introduced especially in the automotive industry. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South-East Asia (SEA). Indulging this situation, FH Joanneum, Austria together with European partners from FH Aachen, Germany and Politecnico Di Torino, Italy is taking initiative to close the gap utilizing the Erasmus+ United grant from EU. A consortium was founded to engage with automotive technology transfer using the European ramework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative, and high-quality training courses to increase graduate’s employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing Universityindustry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future. KW - Erasmus+ United KW - technology transfer KW - UTeM Engineering Knowledge Transfer Unit KW - Malaysian automotive industry Y1 - 2022 SN - 978-981-19-3178-9 SN - 978-981-19-3179-6 (E-Book) U6 - https://doi.org/10.1007/978-981-19-3179-6_50 SN - 2195-4356 N1 - 7th International Conference and Exhibition on Sustainable Energy and Advanced Material (ICE-SEAM 2021), Universiti Teknikal Malaysia Melaka (UTeM), Malaysia, in association with the Universitas Sebelas Maret (UNS), Indonesia, 23 November 2021 SP - 274 EP - 278 PB - Springer Nature CY - Singapore ER - TY - CHAP A1 - Staat, Manfred A1 - Tran, Ngoc Trinh T1 - Strain based brittle failure criteria for rocks T2 - Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training N2 - When confining pressure is low or absent, extensional fractures are typical, with fractures occurring on unloaded planes in rock. These “paradox” fractures can be explained by a phenomenological extension strain failure criterion. In the past, a simple empirical criterion for fracture initiation in brittle rock has been developed. But this criterion makes unrealistic strength predictions in biaxial compression and tension. A new extension strain criterion overcomes this limitation by adding a weighted principal shear component. The weight is chosen, such that the enriched extension strain criterion represents the same failure surface as the Mohr–Coulomb (MC) criterion. Thus, the MC criterion has been derived as an extension strain criterion predicting failure modes, which are unexpected in the understanding of the failure of cohesive-frictional materials. In progressive damage of rock, the most likely fracture direction is orthogonal to the maximum extension strain. The enriched extension strain criterion is proposed as a threshold surface for crack initiation CI and crack damage CD and as a failure surface at peak P. Examples show that the enriched extension strain criterion predicts much lower volumes of damaged rock mass compared to the simple extension strain criterion. KW - Extension fracture KW - Extension strain criterion KW - Mohr–Coulomb criterion KW - Evolution of damage Y1 - 2023 SN - 978-604-357-084-7 N1 - 11th National Conference on Mechanics (NACOME 2022), December 2-3, 2022, VNU University of Engineering and Technology, Hanoi, Vietnam SP - 500 EP - 509 PB - Nha xuat ban Khoa hoc tu nhien va Cong nghe (Verlag Naturwissenschaft und Technik) CY - Hanoi ER - TY - JOUR A1 - Timme, Michael T1 - Beweislast beim gutgläubigen Erwerb eines Kraftfahrzeugs ohne Erhalt der Zulassungsbescheinigung Teil II — Zugleich eine Besprechung von BGH, Urt. v. 23.9.2022 – V ZR 148/21, MDR 2022, 1542 JF - Monatsschrift für Deutsches Recht N2 - Im Handel mit Kraftfahrzeugen gehören Aspekte des gutgläubigen Erwerbs zu den beinahe alltäglichen Standardproblemen. Der BGH fügt in seiner Entscheidung v. 23.9.2022–VZR148/21, MDR 2022, 1541 diesem im Detail breit gefächerten Themenfeld einen weiteren Mosaikstein hinzu: Der Erwerber erhielt das verkaufte Kfz ohne Übergabe einer Zulassungsbescheinigung Teil II, behauptet aber, diese Bescheinigung sei dem vom ihm eingeschalteten Vermittler bei Erwerb (als Fälschung) vorgelegt worden. Tatsächlich befand sich das Original durchgängig beim wahren Eigentümer, der nunmehr Herausgabe des Fahrzeugs verlangt. Der BGH schützt in dieser Gestaltung im Ergebnis den Erwerber. Die Entscheidung ist in mehrfacher Hinsicht bemerkenswert. Y1 - 2022 U6 - https://doi.org/doi.org/10.9785/mdtr-2023-770102 SN - 0340-1812 VL - 77 IS - 1 SP - r5 EP - r7 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - JOUR A1 - Kahmann, Stephanie L. A1 - Rausch, Valentin A1 - Plümer, Jonathan A1 - Müller, Lars P. A1 - Pieper, Martin A1 - Wegmann, Kilian T1 - The automized fracture edge detection and generation of three-dimensional fracture probability heat maps JF - Medical Engineering & Physics N2 - With proven impact of statistical fracture analysis on fracture classifications, it is desirable to minimize the manual work and to maximize repeatability of this approach. We address this with an algorithm that reduces the manual effort to segmentation, fragment identification and reduction. The fracture edge detection and heat map generation are performed automatically. With the same input, the algorithm always delivers the same output. The tool transforms one intact template consecutively onto each fractured specimen by linear least square optimization, detects the fragment edges in the template and then superimposes them to generate a fracture probability heat map. We hypothesized that the algorithm runs faster than the manual evaluation and with low (< 5 mm) deviation. We tested the hypothesis in 10 fractured proximal humeri and found that it performs with good accuracy (2.5 mm ± 2.4 mm averaged Euclidean distance) and speed (23 times faster). When applied to a distal humerus, a tibia plateau, and a scaphoid fracture, the run times were low (1–2 min), and the detected edges correct by visual judgement. In the geometrically complex acetabulum, at a run time of 78 min some outliers were considered acceptable. An automatically generated fracture probability heat map based on 50 proximal humerus fractures matches the areas of high risk of fracture reported in medical literature. Such automation of the fracture analysis method is advantageous and could be extended to reduce the manual effort even further. KW - Fracture classification KW - Shoulder KW - Probability distribution mapping KW - Morphing KW - Imaging Y1 - 2022 SN - 1350-4533 VL - 2022 IS - 110 PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Lebrecht, Rike-Charlotte T1 - Inga : ein modulares hydroponisches System für Endverbraucher N2 - In dieser Arbeit wurde sich mit der Frage auseinandergesetzt, wie sich der Nahrungsmittelanbau im urbanen Raum entwickeln könnte. Eine spannende Alternative zu traditionellen Anbaumethoden ist die Hydroponik, der Anbau von Pflanzen ohne Erde. Basierend auf dieser Technologie wurde in diesem Projekt ein Indoor-Garden-System gestaltet, welches den Nahrungsmittelanbau zurück zur Verbraucher:In bringt und zu einem bewussteren Umgang mit Lebensmitteln anregen soll. Denn mit „INGA“ kann frisches, pestizidfreies Blattgemüse ganz einfach zu Hause selbst angebaut werden. Das hydroponische System schafft mithilfe einer Nährstofflösung und künstlichem Licht optimale Wachstumsbedingungen für die Pflanzen – ganz unabhängig von örtlichen Gegebenheiten. Mithilfe seiner Modularität können Nutzer:Innen „INGA“ nach Belieben konfigurieren. Damit wird es einer breiten Zielgruppe mit unterschiedlichen Bedürfnissen gerecht und ermöglicht pestizidfreie Nahrung – auch in den Städten. KW - Urban KW - Hydroponik KW - Frisches Gemüse KW - Produktdesign KW - Industriedesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Menrath, Maike T1 - Konzept zur Lebensmittelnahversorgung außerhalb urbaner Strukturen : Verkaufspunkt für ländliche Gebiete N2 - Ländliche Regionen sind häufig infrastrukturell schlechter versorgt als urbane Räume, was sich insbesondere auf die Versorgung mit Gütern des täglichen Bedarfs niederschlägt. Menschen außerhalb städtischer Ballungsgebiete müssen deswegen oft lange Anfahrten zu Supermärkten in Kauf nehmen. Hierbei sind sie vor allem auf das Auto angewiesen. In dieser Arbeit ist „ILSE“ entstanden. Eine Verkaufsbox, die Menschen in ländlichen Raumstrukturen besser mit Waren versorgt, indem sie dort aufgestellt wird, wo sie auch wirklich benötigt wird. Dank digitaler Verkaufstechnologien ist „ILSE“ durchgehend geöffnet, auch, wenn andere Supermärkte längst geschlossen sind. Mit einer App wird der Kundschaft der Zugang zum Verkaufsraum und das Bezahlen ermöglicht. KW - Einkauf KW - Lebensmittel KW - ländlich KW - digital KW - regional Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Tabel, Tobias T1 - Sen(se)sation : VR Produktvision mit multisensorischem Einfluss auf die menschliche Wahrnehmung N2 - Das Sen(se)sation VR-Produktkonzept ermöglicht Nutzer*Innen die nahezu vollkommen realistische Darstellung virtuell generierter Welten. Das Konzept ist in genauer Betrachtung des aktuellen Technikstands und der Analyse von Zukunftstrends konzipiert worden und stellt eine Produktvision dar, die in spätestens 5 Jahren problemlos umsetzbar sein wird. Um nicht den Eindruck einer unfundierten Zukunftsvision zu erzeugen, wurde sich bei der Konstruktion der integrierten Features auf aktuell erhältliche Vergleichsprodukte bezogen. Das Sen(se)sation VR System zeigt neue Möglichkeiten die Gestaltungs- und Technikbereich derzeitiger VR Brillen und Controller. Durch die Fokussierung des Produkts auf die Manipulation und Stimulation der fünf Hauptsinne des Menschen wird ein so hoher Grad der Immersion erzeugt, dass die Wahrnehmung von Realität und Virtualität beinah verschwimmen könnte. KW - Virtuelle Realität KW - Sinneserweiterung KW - Multisensorische Wahrnehmung KW - Zukunftsvision KW - Immersion Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Steimel, Nina T1 - An den Rand gedrängt : die Marginalisierung unserer Städte N2 - In der Arbeit »An den Rand gedrängt–Die Marginalisierung unserer Städte« wird anhand des Flächenverbrauchs des ruhenden Verkehrs erörtert, inwieweit der private Pkw die Entwicklung unserer Städte bestimmt. Die Zusammenstellung verschiedener Texte, Raumbeobachtungen und fotografischer Zeitdokumente soll die Problematik und Aktualität des Themas verstärken. Schritt für Schritt sollen die Leser:innen einen neuen Blick auf die eigene Stadt gewinnen und für das Problem der akuten Flächenknappheit sensibilisiert werden. Das Werk versteht sich als Aufruf, unseren Straßenraum zu entkarbonisieren, ihn neu zu entdecken und die möglichen Chancen im Wandel zu erkennen. Dabei geht es zunächst nicht um die Aufzählung von Klimaschäden, die Abschaffung von Parkplätzen oder gar des Autos, sondern um die Auswirkungen, die Parkplätze auf unser Leben haben und vor allem um ihr Potenzial für die Zukunft. KW - Parkplatz KW - Raumnot KW - Verkehrswende KW - Autofrei KW - Mobilitätswende Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Bortmann, Alevtina T1 - Produktion eines „Corporate Identity“- Werbefilms für ein IoT Technologieunternehmen N2 - Mit einem Werbefilm kann man seine Zielgruppe schnell und einfach in wenigen Minuten erreichen, indem man sich als Unternehmen auf eine freundliche Art und Weise vorstellt und somit Vertrauen und Kontakt zu der Zielgruppe herstellt. Außerdem bietet ein Werbefilm eine gute Möglichkeit sein Unternehmen als modernes und leistungsstarkes Unternehmen zu präsentieren, um potenzielle Kunden oder sogar neue Mitarbeiter zu werben. Mit einem überzeugendem Werbefilm, der richtigen Musik und Animation, bleibt ein Werbefilm im Gedächtnis der Zuschauer, viel besser als es Printwerbung in Form von einem Flyer oder einer Broschüre erfüllen kann. Zusätzlich kann man seine Reichweite im Social-Media Bereich um weitere Kanäle erweitern. Dies wiederum ermöglicht dem Unternehmen seinen Kundenstamm zu stärken und auszubauen. KW - CI KW - Werbefilm KW - Video KW - Corporate Identity KW - IT Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Frank, Jemima Leonie T1 - Falling in love with the female gaze N2 - Der „Male Gaze“ bezeichnet das typische Erleben der Umwelt aus männlicher Perspektive und prägt in den sogenannten Mainstream-Medien die Gestaltung von Film, Fernsehen und Werbung. Dadurch werden von dargestellten Personen häufig die körperlichen Aspekte hervorgehoben. Im Gegensatz dazu gilt das weibliche Pendant, der „Female Gaze“, als besonders emotionsbetont. Weil Medien einen enormen Einfluss auf gesellschaftliches und individuelles Denken haben, stellt die Dominanz des „Male Gaze“ eine Unausgeglichenheit dar, die sich in verschiedenen Bereichen des gesellschaftlichen Lebens widerspiegelt. Deswegen möchte dieses Projekt die Medien um die weibliche Sichtweise erweitern und damit die dort transportierten Bilder diverser und ausgewogener machen. Die Fotografie fokussiert sich dabei auf die Gefühlswelt der Protagonistin, womit die Betrachter:Innen schrittweise in ihre Position hineinversetzt werden sollen. Mit Augen des Mitgefühls und eigenem Schönheitsbegriff lässt „Falling in love with the female gaze“ endlich auch die Frau zu Wort kommen. KW - Weiblicher Blick KW - Fotografie KW - Emotional KW - Fühlen KW - Portrait Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Horvath, Nicolas T1 - Neues Corporate Design für das Rautenstrauch Joest Museum Köln N2 - Der Mensch in seinen Welten – das Konzept des Rautenstrauch Joest Museums verfolgt den Ansatz des Kulturvergleichs und strebt im Zuge dessen die Betonung der Ebenbürtigkeit aller Kulturen an. Die Sammlung unterteilt sich nicht – wie gewohnt – anhand geografischer Gesichtspunkte, sondern behandelt Themen, die Menschen auf der ganzen Welt beschäftigen. Das in dieser Arbeit gestaltete neue Erscheinungsbild greift den veränderten gesellschaftlichen Stellenwert von ethnologischen Museen auf und positioniert das Museum als aktiven Diskussionsteilnehmer im Zuge des Postkolonialismus. Das entwickelte Key-Visual aus eigener Schrift, einheitlicher Rastersystematik und prägnantem Farbkonzept gibt einen Einblick darin, wie Menschen früher probiert haben, ihre Welt zu verstehen und sie zu erschließen. KW - Markengestaltung KW - Museum KW - Redesign KW - Postkolonialismus KW - Kunst Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ebert, Julia T1 - Die unsichtbare Gefahr : Mikroplastik N2 - Bereits ein einziger prüfender Blick in einen klassischen Privathaushalt vermittelt einen ersten Eindruck davon, wie allgegenwärtig Kunststoff im menschlichen Leben ist. Häufig übersehen wird dabei Mikroplastik, welches im Verhältnis zu seinen gravierenden Auswirkungen auf Mensch und Umwelt in der öffentlichen Diskussion bislang noch wenig Beachtung findet. Das führt dazu, dass die Problematik durch unaufgeklärten Konsum weiter angefacht wird. Die Gestaltung des visuellen Magazins möchte über die Konsequenzen von Mikroplastik aufklären und das Bewusstsein über das persönliche Konsumverhalten schärfen. Mithilfe kurzer Infotexte wird die Problematik aus der wissenschaftlichen Perspektive der Umweltorganisationen beleuchtet und durch ausgewählte Mikroskop-Aufnahmen illustriert. Hiermit werden unsichtbare Krisentreiber endlich sichtbar gemacht. KW - Mikroplastik KW - Plastik KW - Plastikverpackungen KW - Nachhaltigkeit KW - Massenproduktion Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Braun, Linus T1 - Faces - Lebenswerte Mobilität in Städten N2 - Mobilität stellt oftmals ein Problem in Städten dar. Es sind Staus, Abgase, Platzmangel, die sich negativ auf die urbane Lebensqualität auswirken. Dies sind externe Auswirkungen der von Autos dominierten Mobilität. Ziel von „Faces“ war es, eine effiziente und vor allem attraktive Alternative zum Automobil zu bieten. Dafür denkt das Projekt die Straßenbahn neu. Durch kompaktes Design und die Verwendung autonomer Systeme wird eine höhere Taktung ermöglicht. Zudem werden die Bahnen flexibler und können den Einsatz am Mobilitätsbedarf anpassen. Um den Bedürfnissen der Fahrgäste gerecht zu werden, lässt sich das modulare Interior an die Reisedistanz anpassen. Hier wird ein Mobilitätskonzept gezeichnet, das einem mit einem hoffnungsvollen Blick auf das Leben in den Städten der Zukunft zurücklässt. KW - Mobilität KW - Zukunftsstädte KW - Urbanes Leben KW - Bahnen Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Morandi, Paolo A1 - Butenweg, Christoph A1 - Breis, Khaled A1 - Beyer, Katrin A1 - Magenes, Guido ED - Arion, Cristian ED - Scupin, Alexandra ED - Ţigănescu, Alexandru T1 - Behaviour factor q for the seismic design of URM buildings T2 - The Third European Conference on Earthquake Engineering and Seismology N2 - Recent earthquakes showed that low-rise URM buildings following codecompliant seismic design and details behaved in general very well without substantial damages. Although advances in simulation tools make nonlinear calculation methods more readily accessible to designers, linear analyses will still be the standard design method for years to come. The present paper aims to improve the linear seismic design method by providing a proper definition of the q-factor of URM buildings. Values of q-factors are derived for low-rise URM buildings with rigid diaphragms, with reference to modern structural configurations realized in low to moderate seismic areas of Italy and Germany. The behaviour factor components for deformation and energy dissipation capacity and for overstrength due to the redistribution of forces are derived by means of pushover analyses. As a result of the investigations, rationally based values of the behaviour factor q to be used in linear analyses in the range of 2.0 to 3.0 are proposed. KW - unreinforced masonry buildings KW - modern constructions KW - seismic design KW - linear elastic analysis; KW - behaviour factor q Y1 - 2022 SN - 978-973-100-533-1 N1 - 3ECEES - Third European Conference on Earthquake Engineering and Seismology, September 4 – September 9, 2022, Bucharest SP - 1184 EP - 1194 ER - TY - CHAP A1 - Chico Caminos, Ricardo Alexander A1 - Schmitz, Pascal A1 - Atti, Vikrama Naga Babu A1 - Mahdi, Zahra A1 - Teixeira Boura, Cristiano José A1 - Sattler, Johannes Christoph A1 - Herrmann, Ulf A1 - Hilger, Patrick A1 - Dieckmann, Simon T1 - Development of a micro heliostat and optical qualification assessment with a 3D laser scanning method T2 - SOLARPACES 2020 N2 - The Solar-Institut Jülich (SIJ) and the companies Hilger GmbH and Heliokon GmbH from Germany have developed a small-scale cost-effective heliostat, called “micro heliostat”. Micro heliostats can be deployed in small-scale concentrated solar power (CSP) plants to concentrate the sun's radiation for electricity generation, space or domestic water heating or industrial process heat. In contrast to conventional heliostats, the special feature of a micro heliostat is that it consists of dozens of parallel-moving, interconnected, rotatable mirror facets. The mirror facets array is fixed inside a box-shaped module and is protected from weathering and wind forces by a transparent glass cover. The choice of the building materials for the box, tracking mechanism and mirrors is largely dependent on the selected production process and the intended application of the micro heliostat. Special attention was paid to the material of the tracking mechanism as this has a direct influence on the accuracy of the micro heliostat. The choice of materials for the mirror support structure and the tracking mechanism is made in favor of plastic molded parts. A qualification assessment method has been developed by the SIJ in which a 3D laser scanner is used in combination with a coordinate measuring machine (CMM). For the validation of this assessment method, a single mirror facet was scanned and the slope deviation was computed. KW - Concentrated solar power KW - Electricity generation KW - Measuring instruments KW - Heliostats KW - Global change Y1 - 2022 SN - 978-0-7354-4195-8 U6 - https://doi.org/10.1063/5.0086262 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September–2 October 2020, Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - THES A1 - Scherer, Maike T1 - Social Integrity for distributed Workforces : ein Design System für soziale Interaktion eines Unternehmens N2 - Eine Applikation für die soziale Interaktion zwischen Teams und Arbeitnehmern eines Unternehmens, welche Remote und/oder Hybrid arbeiten. Wissen teilen, Weiterbilden, Wohlfühlen In den letzten zwei Jahren kam es auf Grund der Corona-Pandemie, trotz der vielen Kommunikationsmöglichkeiten, im Privat-, sowie Arbeitsleben zu erheblichen sozialen Einschränkungen. Genau hier setzt die Applikation „Companion“ an, um dem Arbeitnehmer das In-Office-Gefühl auch Remote übersetzen zu können. Der Arbeitnehmer kann mit seinen Kollegen sozialisieren, diese besser kennenlernen und wird zusätzlich durch Events und Workshops professionell weitergebildet. KW - Remote Work KW - Hybrid Work KW - soziale Integration KW - Integration KW - Interaktion Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kaspor, Alexej T1 - Kritik der digitalen Rationalisierung N2 - Digitalisierung macht’s möglich: mittlerweile beziehen sich Designer:innen in ihrer Konzeptentwicklung immer häufiger auf Referenzdesigns. Sie picken sich die Eigenschaften aus ihnen heraus, von denen sie sich die größte Marktfähigkeit versprechen, und basteln sie zu einem neuen Produkt zusammen. Voilà. Doch wie unkonventionell kann Design noch sein? Wie viel Luft bleibt der Kreativität unter dem immer enger geschnürten Korsett der Marktfähigkeit? Alexej Kaspor eröffnet die Diskussion mit einem provokanten Projekt, das einen kritischen Blick in die Zukunft des Industriedesigns wirft. Dazu fasst er gängige Designprogramme in einer Software zusammen und verbindet sie mit einer künstlichen Intelligenz, die die aktuelle Entwicklung digital rationalisieren und auf die Spitze treiben soll. Diese führt Meta-Analysen über das Nutzungsverhalten durch und prüft damit Frameworks von Referenzdesigns auf ihre Vermarktbarkeit. Aus diesen entwickelt sie dann Gestaltungsvorschläge, ohne beim Seiltanz zwischen Trendhörigkeit und Scheinindividualismus aus dem Gleichgewicht zu kommen. Innerhalb von Sekunden werden den Designer:innen perfekte Vorschläge übers Metaverse simuliert. Auf dem Silbertablett serviert, übersichtlich und gefährlich einfach. Bereit, kombiniert und in Produktion gebracht zu werden. Auch mit dem Tracking der KI kann niemand mithalten: um immer am Puls der Zeit zu bleiben, benachrichtigt sie die Designer:innen in Echtzeit über die neuesten Innovationen und Trends. Ressourcenraubendes Herumprobieren in CAD-Programmen gehört also der Vergangenheit an. Das Programm schafft Abhilfe, und verspricht dabei auch noch die höchste Effizienz, konkret: garantiertes Kapital. Schlagende Argumente, die die Schwächen der Konsumgesellschaft und Kommerzialisierung gezielt ausgenutzen. Es entsteht die perfekte Marketingmaßnahme, ein genialer Treiber für den Turbokapitalismus. Kram, den niemand braucht und zynische Statussymbole inklusive. Der Stolz der geltungsbedürftigen Designer:innen wird dabei selbstverständlich nicht untergraben. Sie sollen mitziehen. Mit zahlreichen Notches wird der Erfolg und die Konkurrenzfähigkeit des Produkts prognostiziert und ihnen Honig ums Maul geschmiert. Die beklemmende Vorahnung wird sich bestätigen. Schritt für Schritt enteignet die KI den Designer:innen ihre Kreativität, bis sie nicht mehr sind als die Kurator:innen berechenbarer Produktkonzepte. Der Spätkapitalismus hat sie in der Mangel. Versprochen: diese Arbeit lässt niemanden kalt. KW - Digitalisierung KW - Designprogramme KW - Nutzungsverhalten KW - Marktfähigkeit KW - künstliche Intelligenz Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Sattler, Johannes Christoph A1 - Schneider, Iesse Peer A1 - Angele, Florian A1 - Atti, Vikrama Naga Babu A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Development of heliostat field calibration methods: Theory and experimental test results T2 - SolarPACES 2022 conference proceedings N2 - In this work, three patent pending calibration methods for heliostat fields of central receiver systems (CRS) developed by the Solar-Institut Jülich (SIJ) of the FH Aachen University of Applied Sciences are presented. The calibration methods can either operate in a combined mode or in stand-alone mode. The first calibration method, method A, foresees that a camera matrix is placed into the receiver plane where it is subjected to concentrated solar irradiance during a measurement process. The second calibration method, method B, uses an unmanned aerial vehicle (UAV) such as a quadrocopter to automatically fly into the reflected solar irradiance cross-section of one or more heliostats (two variants of method B were tested). The third calibration method, method C, foresees a stereo central camera or multiple stereo cameras installed e.g. on the solar tower whereby the orientations of the heliostats are calculated from the location detection of spherical red markers attached to the heliostats. The most accurate method is method A which has a mean accuracy of 0.17 mrad. The mean accuracy of method B variant 1 is 1.36 mrad and of variant 2 is 1.73 mrad. Method C has a mean accuracy of 15.07 mrad. For method B there is great potential regarding improving the measurement accuracy. For method C the collected data was not sufficient for determining whether or not there is potential for improving the accuracy. KW - Heliostat Field Calibration KW - Unmanned aerial vehicle KW - UAV KW - Quadrocopter KW - Camera system Y1 - 2024 U6 - https://doi.org/10.52825/solarpaces.v1i.678 SN - 2751-9899 (online) N1 - SolarPACES 2022: 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Sattler, Johannes Christoph A1 - Atti, Vikrama Naga Babu A1 - Alexopoulos, Spiros A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf A1 - Dutta, Siddharth A1 - Kioutsioukis, Ioannis T1 - DNI forecast tool for the smart operation of a parabolic trough collector system with concrete thermal energy storage: Theory, results and outlook T2 - SolarPACES 2022 conference proceedings N2 - This work presents a basic forecast tool for predicting direct normal irradiance (DNI) in hourly resolution, which the Solar-Institut Jülich (SIJ) is developing within a research project. The DNI forecast data shall be used for a parabolic trough collector (PTC) system with a concrete thermal energy storage (C-TES) located at the company KEAN Soft Drinks Ltd in Limassol, Cyprus. On a daily basis, 24-hour DNI prediction data in hourly resolution shall be automatically produced using free or very low-cost weather forecast data as input. The purpose of the DNI forecast tool is to automatically transfer the DNI forecast data on a daily basis to a main control unit (MCU). The MCU automatically makes a smart decision on the operation mode of the PTC system such as steam production mode and/or C-TES charging mode. The DNI forecast tool was evaluated using historical data of measured DNI from an on-site weather station, which was compared to the DNI forecast data. The DNI forecast tool was tested using data from 56 days between January and March 2022, which included days with a strong variation in DNI due to cloud passages. For the evaluation of the DNI forecast reliability, three categories were created and the forecast data was sorted accordingly. The result was that the DNI forecast tool has a reliability of 71.4 % based on the tested days. The result fulfils SIJ’s aim to achieve a reliability of around 70 %, but SIJ aims to still improve the DNI forecast quality. KW - Direct normal irradiance forecast KW - DNI forecast KW - Parabolic trough collector KW - PTC KW - Thermal Energy Storage Y1 - 2024 U6 - https://doi.org/10.52825/solarpaces.v1i.731 SN - 2751-9899 (online) N1 - SolarPACES 2022, 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - THES A1 - Krebs, Benedikt T1 - Das Online-Ich : Erlebnis-Installation zur Reflexion über das digitale Selbst N2 - Soziale Netzwerke gehören zu den größten Konzernen der Welt. Hier werden minütlich Millionen von Nachrichten verschickt. Das Internet spielt eine stetig wachsende Rolle in der zwischenmenschlichen Kommunikation. Und doch funktioniert dort nicht nur die Sprache anders, auch die Persönlichkeit der Menschen kann sich auch verändern. Diese Arbeit beschäftigt sich mit dem „Online-Ich“, das jeder in sich tragen soll. Häufig ist dieses offener, hilfsbereiter und selbstloser, aber eben auch reizbarer, aggressiver und energetischer. Um auf diese Veränderung aufmerksam zu machen, werden die analoge und digitale Persönlichkeit verglichen. Dazu schöpft die Arbeit aus den vielfältigen Möglichkeiten von Virtual Reality, um Betrachtende in die Arbeit miteinzubeziehen. KW - Virtuelle Realität KW - Online KW - Enthemmung KW - Messestand KW - 3D Y1 - 2022 PB - FH Aachen CY - Aachen ER -