TY - JOUR
A1 - Daniel, Bernd
A1 - Starck, Andreas
T1 - Kostenkontrolle und Kostensteuerung im Hochbau
N2 - Textauszug: Nach dem Leistungsbild der HOAI hat der Architekt bei Planung und Baubetrieb vier Stationen der Kostenermittlung entsprechend der DIN 276, Abschnitt 2.3 abzuarbeiten. Der Architekt, der seiner Verantwortung gerecht werden will, wird hier weitere Kontrollmechanismen einbauen wollen. Über die genannten Kostenermittlungen hinaus kennt die DIN 276 daher noch das Erfordernis der Kostenkontrolle in Abschnitt 2.4 und der Kostensteuerung in Abschnitt 2.5. Die Kostensteuerung greift immer dann, wenn die Kostenkontrolle eine Abweichung des Kostenrahmens von den Sollwerten aufzeigt. Dazu müssen die Kontrollinstanzen dort eingebaut werden, wo Korrekturen noch möglich sind. Eine erste Kontrolle der Kosten ist daher zwischen Massenermittlung und Vergabe sinnvoll einzuflechten. Zu diesem Zeitpunkt kann die Planung noch verändert werden, was einen ersten steuernden Eingriff in die Baukosten ermöglicht, und zwar bevor die Angebotsunterlagen verschickt werden. Die Grundlagen zu einer effektiven Kostensteuerung werden in der Mengenermittlung der Leistungsphase 6 gelegt. Wenn dort die Mengen nicht sorgfältig und nachvollziehbar ermittelt wurden, wird der Soll- Ist- Abgleich während der Bauphase nicht frühzeitig genug gelingen, wenn nicht gar ganz entfallen. Es gilt also, dafür zu sorgen, dass die Mengenermittlung zur Vergabe mit entsprechender Sorgfalt und vor Allem „projektnah“ erfolgt. Schätzungen haben hier keine Berechtigung.
KW - Projektsteuerung
KW - Baukosten
KW - Kostenkontrolle
KW - Kostensteuerung
KW - Kostenermittlung
Y1 - 2007
ER -
TY - GEN
A1 - Samm, Doris
A1 - Witte, Tim
T1 - Virtuelles Labor zur Verarbeitung elektronischer Signale
N2 - Oberfläche zur Simulation einfacher Praktikumsversuche mit dem NIM System. Programmiert mit Flash MX. Die Simulation verschafft virtuellen Einblick in ein Pulselektroniklabor.
KW - Impulstechnik
KW - Signalquelle
KW - Simulation
KW - Virtuelle Realität
KW - Pulselektroniklabor
Y1 - 2003
ER -
TY - BOOK
A1 - Merten, Sabine
T1 - Verbesserung der Ausbildung in der Mikrosystemtechnik - virtuelle Labore bereiten auf die Herstellung realer Drucksensoren vor (2 Fassungen: konvertiert und original
N2 - Die Ausbildung in Hochtechnologien wie beispielsweise der Mikrosystemtechnik ist oft durch einen hohen Grad an Komplexität charakterisiert. Damit verbunden sind hohe Kosten für die Errichtung und den Betrieb der speziellen Laborräume und ihre häufig geringe Verfügbarkeit für die Studierenden. Zukünftige Ingenieure sammeln während ihrer Ausbildung aus diesen Gründen nur in beschränktem Umfang praktische Erfahrungen. Die Industrie hingegen fordert Personal mit hoher fachlicher Kompetenz, also fundiertem theoretischen Wissen und umfangreichen praktischen Kenntnissen. Dieser Diskrepanz – qualifizierte Ingenieure auf der einen Seite und eine eher theoretisch ausgerichtete Ausbildung auf der anderen Seite – wird mit einem neuen Blended-Learning-Konzept für MST-Technologiepraktika begegnet. Lernende werden über ein virtuelles Labor, das einen echten Reinraum mit realen Anlagen simuliert, intensiv auf reale Laborpraktika vorbereitet. Dabei geht es im virtuellen Labor gleichermaßen um die Vermittlung von Theorie und Praxis. Nur trainierte Teilnehmer mit einer intensiven Vorbereitung sind in der Lage, relativ eigenständig ein echtes MST-Bauteil innerhalb des anschließenden einwöchigen Laborkurses zu fertigen. Die Wirksamkeit des Konzeptes und die Steigerung des Lernerfolges durch die kombinierten virtuellen und realen Laborkurse wurden im Rahmen der Dissertation begleitend untersucht. Die Ergebnisse flossen direkt in die Weiterentwicklung der Technologiepraktika ein. Die Konzepte und Erkenntnisse sind zudem sehr interessant für die Entwicklung von Blended-Learning-Angeboten in ähnlichen oder anderen Fachgebieten sowie für weitere Bildungseinrichtungen. (Die Dissertation liegt hier in 2 Fassungen vor: Die Originalfassung ist nur bei guter Rechnerausstattung und guter Netzanbindung nutzbar, die konvertierte Fassung ist unverändert, allerdings sind Qualitätseinbußen beim Ausdruck einiger Grafiken möglich)
N2 - Education in high technologies, like e.g. Microsystems technology, is usually characterized by a high degree of complexity. In addition it is usually connected with large economic efforts for invest, operation and maintenance of the special laboratory facilities. The access to such facilities for educational purposes is often quite limited. Therefore engineering students rather rarely gather practical experience in such technologies during their university studies. In contrast, industry has a large demand for engineers with high professional competence, i.e. profound theoretical knowledge combined with substantial practical experience. The newly developed blended learning concept for MST laboratory training tries to bridge the gap between the need for qualified engineers and the more theoretical university education. The learners prepare intensively for real hands-on clean room trainings with a virtual technology laboratory, i.e. a computer simulation of the clean room machines and the corresponding processes. In the virtual technology laboratory the students brush up their theoretical knowledge and at the same time learn to operate the complex clean room machines. Only well trained and intensively prepared students are capable to produce a fully functional MST component within a compact clean room laboratory course of only one week duration and an only modest amount of supervision. The effectivity of this concept and the increase of the learning success due to the specific mixture of virtual and real laboratory sessions has been accompanied and analysed by this dissertation. The results have been used to further improve the laboratory courses. Concepts and results are also very attractive for comparable blended learning proposals in other technical disciplines.
KW - Mikrosystemtechnik
KW - Virtuelles Laboratorium
KW - Lernprogramm
KW - Hochschule / Lehre / Evaluation
KW - Computersimulation
KW - Drucksensor
KW - Blended-Learning
KW - Reinraumpraktikum
KW - blended learning
KW - hands-on cleanroom training
Y1 - 2005
N1 - Zugl.: Saarbrücken, Univ., Diss., 2005
ER -
TY - GEN
A1 - Samm, Doris
T1 - Horizontal schwingende Feder (Simulation in Java)
N2 - Die Anwender können die Federkonstante, die Amplitude und die Masse einstellen. Es werden die Änderung der kinetischen und potentiellen Energie angezeigt und die Auslenkung als Funktion der Zeit dargestellt.
KW - Feder
KW - Amplitude
KW - Auslenkung
KW - Javasimulation
Y1 - 2003
ER -
TY - GEN
A1 - Samm, Doris
T1 - Vertikal schwingende Feder (Simulation in Java)
N2 - Die Anwender können die Federkonstante, die Amplitude und die Masse einstellen. Die Änderung der kinetischen und potentiellen Energie werden angezeigt und die Auslenkung als Funktion der Zeit dargestellt.
KW - Feder
KW - Amplitude
KW - Auslenkung
KW - Javasimulation
Y1 - 2003
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2002; Sonderbeilage Energie
N2 - Energiecontrolling an der Fachhochschule Aachen Solar-Institut Jülich: Ziele und Philosophie Forschung und Entwicklung Anwendung und Verbreitung Beratung und Information Ausbildung und Schulung Projektbeispiele Nowum-Energy Ressourceneinsparung auf dem Solar-Campus Jülich Fachtagung: Energie-Management Pilotprojekt: Umrüstung von Hörsälen mit moderner Gebäudesystemtechnik
T3 - Fachblatt / FH Aachen - 2002, S_Energie
KW - Fachhochschule Aachen
KW - Erneuerbare Energien
KW - Energiecontrolling
KW - Aachen University of Applied Sciences
KW - Renewable Energy
KW - Energy controlling
Y1 - 2002
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2002; Nr. 3
N2 - Forschungs- und Technologietransfer - Wege in die Wirtschaft Neu entwickelte Software für Datenschützer im Einsatz Den Stempel aufgedrückt - Gütesiegel für Studiengänge Aufgestiegen - Fachhochschulen spielen in der ersten Liga Arbeitsbelastung - Viele Studenten kapitulieren vor der Regelstudienzeit 100 Jahre Ingenieurausbildung Prof. Schiffers - jede Menge Musik im Blut Prof. Dr. Mang - Professor mit Markenzeichen Prof. Dr. Ing. Gerhard Seehausen Prof. Dieter Rehder über Aufgaben und Ziele im Fachbereich Design Prof.Dr.-Ing. Gregor Krause jung, dynamisch, voller Tatendrang Studierende des Fachbereichs Design führen einen Dialog mit Europa ZARM-Förderpreis für Absolventin der FH Aachen Personal-Info Leinen los für die Gorch Frog Wildnisinsel inmitten der Stadt Die FH Aachen hat gewählt Kritik an Studiengebühren Das neue Corporate Design der Stadt Aachen Rachel MdB: Schnelle Hilfe für FH Aachen Landesrektorenkonferenz an der FH Aachen Nutzung alternativer Energiequellen wird immer wichtiger Zukunftswerkstatt Biosensorik Ballone und Luftschiffe aus Sicht der Rechtswisschenschaft HBZ-Informationsdienst Tag der Forschung
T3 - Fachblatt / FH Aachen - 2002, 3
KW - Fachhochschule Aachen
KW - Aachen University of Applied Sciences
Y1 - 2002
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2002; Sonderbeilage Auto
N2 - Sparsam, leise, völlig unkonventionell: Raktor auf Samtreifen Porsche Athletic Aerodynamik und Design Koopertion zwischen Handwerk und Hochschule „Meinen Studenten empfehle ich die DFK“ Erkursion: Karmann Qualitätsmanagement
T3 - Fachblatt / FH Aachen - 2002, S_Auto
KW - Fachhochschule Aachen
KW - Kraftfahrzeug
KW - Auto
KW - Aachen University of Applied Sciences
KW - Car
Y1 - 2002
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2003; Nr. 1
N2 - Forschung & Lehre Die solare Küche Laboreinweihung am Fachbereich Bauingenieurwesen StudiengängeFacility Management – Erfolgreicher Start Energy Systems CMD Studentinnen und Studenten – Die Zukunft fest im Griff Internationales Studentenaustausch mit der Polytechnischen Hochschule Pskov, Russland Eurostudium am Fachbereich Wirtschaftswissenschaften FH-Service Rekordverdächtig – 500 000. Besucherin in der Bereichsbibliothek Eupener Straße Absolventen aufgepasst! Neue Alumni-Seite im Internet Personen Höchste Ehrung für Prof. Dr.-Ing. Hövelmann Wahlen an den Fachbereichen – Wir gratulieren der neuen Dekanin und unseren Dekanen! Personalinfo Aus den Fachbereichen Hundert Jahre Ingenieurstudium Aachener Tunnelexperte macht nicht nur NRW-Röhren sicherer
T3 - Fachblatt / FH Aachen - 2003, 1
KW - Fachhochschule Aachen
Y1 - 2003
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2003; Sonderheft "Tag der Forschung"
N2 - Editorial Bioengineering – Schulterschluss von Ingenieuren und Naturwissenschaftlern Die Life Sciences der Region Aachen-Jülich zwischen „Bio-River“ und dem „Life Science Triangle Maas/Rhein“ Cellularengineering – Was suchen Ingenieure in der Biologie? Zukunftswerkstatt Biosensorik Pharmakogenetik- Wie man mit Hilfe der eigenen Gene die wirksamsten Medikamente findet Kultivierung blutbildender Zellen im Bioreaktor Kunststoffpartikel in Medizin und Biotechnologie Automotive Engineering. Der Wettlauf um das andere Auto car e.V. – Das unabhängige Competence Center der Automobiltechnik Motorentechnologien der Zukunft Die Fahrzeugkarosserie von morgen Simulation mechatronischer Systeme im Automobil Gezielte Entwicklung von Fahrwerkskomponenten mit Hilfe moderner Berechnungsverfahren Hochtechnologie in der KFZ-Restauration Akustikwindkanal für DaimlerChrysler/USA Technology gegen Ton im Auto-Design Podiumsdiskussion „Physiotherapie-Studium künftig auch in Nordrehin-Westfalen an Fachhochschulen?“ Förderung von Unternehmen und Hochschulen im Doppelpack – „PROgramm INNOvationskompetenz mittelständischer Unternehmen“ (PRO INNO) der AiF Diskussionsrunde zum Thema „Ingenieurstudium – Lohnt sich das?“ Globalisierung – Ist die Welt noch zu retten? Expertenrunde zum Thema „Stammzellenforschung – Möglichkeiten und Grenzen“ Kontaktmesse im Foyer Begleitprogramm Sponsoren
T3 - Fachblatt / FH Aachen - 2003, S_TdF
KW - Fachhochschule Aachen
KW - Bioingenieurwesen
KW - Kraftfahrzeugtechnik
KW - Aachen University of Applied Sciences
KW - Bioengineering
KW - Automotive engineering
Y1 - 2003
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2003; Nr. 2
N2 - Forschung & Lehre Fachhochschule Aachen auf der IAA 2003 Zehn Studenten der Fachhochschule Aachen entwickeln neue Landschaftsmöbel Erfolgreiche Forschung am Lehrgebiet Hoch- und Höchstfrequenztechnik Studiengänge MBA Studiengang „Entrepreneurship“ in Düren nun bald mit Qualitätssiegel Der neue Studiengang Communication and Multimediadesign beginnt Internationales Lehr- und Forschungsnetz der FH spannt sich bis nach Florida Wissenschaftler der FH Aachen „Down-Under“ sehr gefragt FH-Service Auf dem Weg zur Marke – Die FH präsentiert ihre neuen Produkte Die Weiterbildung „UmBau“ und der Gerling-Pavillon in Jülich Drei starke Partner ein Link: Die „AachenJuelichBib“ Personen Personalinfo Seit 30 Jahren im „Sattel“ – Dienstjubiläum von Reiner Smeetz Neuer stellvertretender Bibliotheksleiter Klaus-Dieter Thormann
T3 - Fachblatt / FH Aachen - 2003, 2
KW - Fachhochschule Aachen
KW - Aachen University of Applied Sciences
Y1 - 2003
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2004; Nr. 1
N2 - Forschung & Lehre Zukünftige Herausforderungen in der Antriebstechnik Mit 150 km/h an der Decke fahren Bau-Solar-Tag Ausbildung in neuen CAx-Labor Drei Jahre INGMEDIA - Was bleibt? Cells at Work II hdw-nrw-fh: neues Weiterbildungsprogramm 2004 FH-Service Schnellstart mit Ampelsystem - neuer Zugang zu elektronischen Zeitschriften Hochschulstandort Aachen auf dem Weg zum Exzellenzzentrum Frischer Wind in der Alumni-Arbeit der FH - Gründung des Vereins "alfha.net" MLP eröffnet Büro in der Bayernallee Personen Kurt Schmidt - Ein Mann der ersten Stunde Drei ungewöhnliche Absolventen der Fachhochschule Personal - Info Internationales INCAS - Ein wichtiger Beitrag zum interkulturellen Dialog in Aachen Studiengänge Fulminanter Start des CMD-Studiengangs Aus den Fachbereichen sub-art auf der "Boot"
T3 - Fachblatt / FH Aachen - 2004, 1
KW - Fachhochschule Aachen
KW - Aachen University of Applied Sciences
Y1 - 2004
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2004; Nr. 2
N2 - Forschung & Lehre Zukünftige Herausforderungen in der Antriebstechnik, Teil 2 Hochfrequenztechniker der FH Aachen auf internationaler Konferenz Beton jetzt mit Glasfasertechnik Gründung des "Institutes für Angewandte Polymerchemie" der FH Aachen Solar-Institut Jülich qualifiziert Gebäudeenergieberater Schützt innovative Neuentwicklung der FH Aachen bald den Papst Neue Maßstäbe zur Bewertung von Sonnenschutzsystemen FH-Service Landesrektorenkonferenz der Fachhochschulen NRW an der FH Aachen WebKollegNRW stellt "Neues Lernen mit dem Internet" vor Ohne starken Partner keine Karriere mit Kind (Fast) Alles im grünen Bereich - Internet-Umfrage der Bibliothek Personen Brunel GmbH: Karrierechancen im Bereich Ingenieurdienstleistungen DAAD-SOKRATES/ERASMUS - Expertin mit Spezialgebiet Curriculumentwicklung und ECTS Personal - Info Internationales Pat Cox erhielt den Internationalen Karlspreis zu Aachen Sonstiges "Technik für Kinder" im Brückenkopfpark Aus den Fachbereichen Ticket nach New York für eine dufte Idee - FH-Studentinnen designen Kaffeedosen
T3 - Fachblatt / FH Aachen - 2004, 2
KW - Fachhochschule Aachen
KW - Aachen University of Applied Sciences
Y1 - 2004
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2005; Nr. 1
N2 - Forschung & Lehre FH Aachen: Spitzenplatz in Forschung und Entwicklung Erfolgreiche Weichenstellung für die Zukunft Capro steht nicht bloß für eine Studie Erste Absolventen des MBA-Studiengangs "Entrepreneurship" verabschiedet automotive and aerospace industries Eine Legende lebt - der Porsche 917-024 K 8. Tag der Forschung FH-Service Neues e-journal an der FH Aachen Das neue Online-Tutorial der Bibliothek Die Personalräte der FH Aachen Studieren mit Kind an der FH Aachen Personen Personal-Info Drei Fragen an... Prof. Gerhard Dikta Inna Brauer, eine erfolgreiche FH-Absolventin, startet durch Solar-Institut Jülich Neues aus dem Solar-Institut Jülich Kurz notiert "Merci papa, merci maman" Aus den Fachbereichen Forschung im Weltraum Wie real ist Science-Fiction? Tagung am Institut für Angewandte Polymerchemie
T3 - Fachblatt / FH Aachen - 2005, 1
KW - Fachhochschule Aachen
KW - Aachen University of Applied Sciences
Y1 - 2005
ER -
TY - CHAP
A1 - Gebhardt, Andreas
A1 - Schmidt, Frank-Michael
T1 - Farbige Prototypen als Werkzeug für den Konstrukteur
T1 - Colored prototypes as instrument for the constructing engineer
N2 - Physische Prototypen, also Anschauungs- und Funktionsmodelle nach den generativen oder Rapid Prototyping (RP) Verfahren haben sich in diesem Zusammenhang vor allem als Hilfsmittel zur effektiven Kommunikation und zur Evaluierung von Produkteigenschaften einen festen Platz in der Produktentstehung erworben. Die positiven Effekte der etablierten RP Verfahren sind unumstritten. Einfachere, schnellere und wirtschaftlichere Maschinen (Prototyper, Fabrikator), vor allem auch für die Büroumgebung, geben neue Impulse im Sinne der Optimierung der heutigen Verfahren. Eine neue Dimension verspricht die Option „Farbe“ der bisher fast ausschließlich monochromen Modelle. Ist Farbe nur „nice to have“ oder welchen Effekt haben farbige Modelle als Werkzeug von Konstrukteuren und Produktenwicklern? Welche Perspektiven bietet „Farbe“ darüber hinaus?
KW - Prototyping
KW - Rapid prototyping
KW - Prototypen
KW - Funktionsmodelle
KW - Produktentstehung
KW - Prototyper
KW - Produktenwicklung
KW - prototypes
KW - working models
KW - product emergence
KW - prototyper
KW - product development
Y1 - 2005
ER -
TY - CHAP
A1 - Brüssermann, Klaus
A1 - Deuster, M.
T1 - Temperature measurement to optimise the burning process
N2 - One of the most important parameters in a burning chamber - in power stations, in waste to energy plants - is the temperature. This temperature is in the range of 700-1500 °C - one of the most advanced measuring methods being the acoustic pyrometry with the possibility of producing temperature mapping in one level of the burning chamber - comparable to computer tomography. The results of these measurements discussed in the presentation can be used - to fulfil the legal requirements in the FRG or in the EU - to equalise the temperature in one level of the burning chamber to optimise the steam production (better efficiency of the plant) and to minimise the production of temperature controlled flue gas components (NO, CO a. o.) - to control the SNCR-process if used.
KW - Pyrometrie
KW - Temperaturmessung
KW - temperature measurement
KW - acoustic pyrometry
KW - steam production
KW - flue gas components
Y1 - 2005
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2006; Nr. 1
N2 - Studienbeiträge Die schwere Geburt des Studienbeitragsgesetzes Forschung Erfindungen für die Praxis Antikensammlung inszeniert in geschwungener Ebenenkonstruktion Doppelt hält besser Studium und Lehre Kreative Höhenflüge im Weinberg von Piemont Nach "Bauhaus Europa" jetzt "Kunsthaus Aachen" Beton - Es kommt drauf an, was man draus macht "Ein Stück Raumfahrtsystem" Film ab im Cinekaree Umstellung auf Bachelor- und Master-Abschlüsse beispielhaft Herausragende architektonische Umsetzung geehrt Erdbeobachtung im Taschenformat Die Hygiene im Handgepäck Eintauchen in die Welt von "sub-ten" Symposium zur 1. Flugmesswoche des FB 6 Personen Konsul mit Zeitungsente Der richtige Mann am richtigen Ort Urlaub fürs Ehrenamt 101 und ziemlich weise Goldene Auszeichnung für die Dekanin Wir feiern heute unsere Eliten Eigene Faszination für den Lehrstoff fesselt Studierende Personalia Horst Rambau: Endstation Selbstständigkeit? Der gute Ruf reicht bis Teheran Alumni "Regen ist gut für unser Geschäft" FH-Studenten aus Jülich in der Wissenschaft erfolgreich Miss und Mister FH 2005 International Vor 20 Jahren begann es! "Heute ist ein guter Tag für die Fachhochschule" Service Bologna ist längst bei den Hochschulen angekommen Auch Lehrer lernen nie aus Was ist eigentlich das Freshman-Year "Zeile für Zeile"
T3 - Fachblatt / FH Aachen - 2006, 1
KW - Aachen / Fachhochschule Aachen
KW - Fachhochschule Aachen
KW - Aachen University of Applied Sciences
Y1 - 2006
ER -
TY - CHAP
A1 - Gebhardt, Andreas
T1 - Technology Diffusion through a Multi-Level Technology Transfer Infrastructure. Contribution to the 1st. All Africa Technology Diffusion Conference Boksburg, South Africa June 12th - 14th 2006
N2 - Table of contents 1. Introduction 2. Multi-level Technology Transfer Infrastructure 2.1 Level 1: University Education – Encourage the Idea of becoming an Entrepreneur 2.2 Level 2: Post Graduate Education – Improve your skills and focus it on a product family. 2.3 Level 3: Birth of a Company – Focus your skills on a product and a market segment. 2.4 Level 4: Ready to stand alone – Set up your own business 2.5 Level 5: Grow to be Strong – Develop your business 2.6 Level 6: Competitive and independent – Stay innovative. 3. Samples 3.1 Sample 1: Laser Processing and Consulting Centre, LBBZ 3.2 Sample 2: Prototyping Centre, CP 4. Funding - Waste money or even lost Money? 5. Conclusion
KW - Technologietransfer
KW - technology transfer
KW - technology diffusion
Y1 - 2006
ER -
TY - JOUR
A1 - Gebhardt, Andreas
T1 - Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping"
N2 - Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering – Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision
KW - Rapid prototyping
KW - Rapid Technologie
KW - Rapid Prototyping
Y1 - 2006
ER -
TY - GEN
A1 - Junold, Thomas
T1 - Schwarz. Weiss. Ein dokumentierter Schriftentwurf
T1 - Black. White. A commented type design
N2 - Schwarz und Weiß. Schwarze Glyphen, weiße Gegenformen. Schwarze Zeilen, Weißraum als Gestaltungselement. Schwarze Schrift auf weißem Papier. Schrift als Kommunikationselement. Vereinheitlichte und vereinfachte Formen, dank Jahrhunderte langer Gewöhnung oder Experimentierfeld für Formen, die sich mit verändernden Techniken gleichermaßen verändern? Schrift als Vermittler von Emotionen oder reine Information. Was macht eine Schrift lesbar und was steht einer »Display-Schrift« gut zu Gesicht? Sind Schriftsippen mit über hundert Schnitten Anwenderfreundlich oder eher Grund für Verwirrung. Serifenschrift oder Sans-Serif? Was ist moderner? Sind wir Kinder der Helvetica oder der Frutiger oder eher Enkel der Garamond oder Bodoni? Kann man ein ästhetisches Empfinden für Schrift lernen? Eine Schrift als Beweis, ausgebaut für eine sinnvolle Verwendung, hinterfragt durch einen Markt schon während ihrer Entstehung. Rückführung und Begründung der aufgeführten Fragen auf diese Schrift. Ein Diplom, das nachdenkt über Schrift, das Schrift anbietet, den Dialog mit Schrift fordert.
N2 - When asked why there are so many typefaces, Adrian Frutiger used to reply: “Because there is so many wines.” Source: Fontblog Black and white. Black glyphs, white counters. Black lines of text, white space as design element. Black type on white paper. Type as an element of comunication. Unified and simplified forms, that change along ever-changing technology? Typefaces as mediators of emotion or pure information. What makes a typeface readable and what makes a pure display typeface pleasant? Are typeface superfamilies with more that a hundered styles user friendly or a blessing or a curse? Serifed or unserifed? What is more modern? Are we the children of Helvetica or Frutiger, or the grandchildren of Garamond and Bodoni? Can a sensitivity to the power of type be learned? A typeface as a proof, equipped for sensible use, and questioned by the market already during its conception. Feedback and integration of these questions in the typeface. A “diploma” that thinks about type, that offers type, that calls for dialogue with type. By using type, you take responsibility.
KW - Schriftkunst
KW - Forum Typografie
KW - Typographie
KW - Spiekermann
KW - Erik
KW - Actor
KW - Schrift
KW - Open Type
KW - Schriftentwurf
KW - Fontlab
KW - actor
KW - font
KW - open type
KW - typedesign
KW - fontlab
Y1 - 2006
ER -
TY - GEN
A1 - Schneider, Bettina
T1 - Finanzierung und Liquiditätssicherung. Teil 1. BWL für Ingenieure
N2 - Finanzierung und Liquiditätssicherung. Teil 1. BWL für Ingenieure. 10 Folien neue Version vom 06.12.2004 Gliederung: 1. Begriffe und Ziele 2. Finanzplanung 3. Finanzierungsquellen Zugriff nur auf dem Campus oder per Virtual Private Network VPN
KW - Finanzierung
KW - Liquiditätspolitik
KW - Betriebswirtschaftslehre
Y1 - 2004
ER -
TY - GEN
A1 - Schneider, Bettina
T1 - Finanzierung und Liquiditätssicherung. Teil 2. BWL für Ingenieure
N2 - Finanzierung und Liquiditätssicherung. Teil 2. BWL für Ingenieure. 12 Folien Neue Version vom 6.12.2004 3. Finanzierungsquellen Zugriff nur innerhalb des Campus oder per Virtual Private Network VPN
KW - Finanzierung
KW - Liquiditätspolitik
KW - Betriebswirtschaftslehre
Y1 - 2004
ER -
TY - GEN
A1 - Schneider, Bettina
T1 - Finanzierung und Liquiditätssicherung. Aufgaben. BWL für Ingenieure
N2 - 5 Folien neue Version vom 6.12.2004 Zugriff nur auf dem Campus oder per Virtual Private Network VPN
KW - Finanzierung
KW - Liquiditätspolitik
KW - Betriebswirtschaftslehre
Y1 - 2004
ER -
TY - GEN
A1 - Schneider, Bettina
T1 - Finanzierung und Liquiditätssicherung. Lösungen. BWL für Ingenieure
N2 - 10 Folien. Lösungen zu Finanzierung und Liquiditätssicherung. Zugriff nur auf dem Campus oder per Virtual Private Network VPN
KW - Finanzierung
KW - Liquiditätspolitik
KW - Betriebswirtschaftslehre
Y1 - 2004
ER -
TY - GEN
A1 - Rößler, Edith
A1 - Le, Thi Lai
A1 - Otto, Moritz
T1 - Freilicht
T1 - Open-air
N2 - Eine kurze Folge einer Fernsehsendung namens "Freilicht", die Umweltprobleme und deren Lösungsmöglichkeiten in parodistischer Weise darstellt.
N2 - A short episode of a television show called "Open-air" which displays environmental problems and possible solutions in a mocking way.
KW - Mediendesign
KW - Filmregie
KW - Dokumentarfilm
KW - Talkshow
KW - Parodie
KW - Fernsehen
KW - Filmdesign
KW - Studienarbeit
KW - Projektarbeit
KW - Fernsehsendung
KW - Television
KW - Television show
KW - Film design
KW - Project
Y1 - 2004
ER -
TY - GEN
A1 - Bissels, Anne
A1 - Jahn, Amelie
T1 - Multiplex
T1 - Multiplex
N2 - Eine kurze Folge einer Fernsehsendung namens Multiplex. Gesendet wird ein Portait der kubanischen Diva Omara Portuondo auf Europatournée.
N2 - A short episode of a television dokumentary series called multiplex. The episode features the portrait of the cuban diva Omara Portuando touring Europe.
KW - Mediendesign
KW - Filmregie
KW - Dokumentarfilm
KW - Talkshow
KW - Fernsehen
KW - Filmdesign
KW - Studienarbeit
KW - Projektarbeit
KW - Fernsehsendung
KW - Television
KW - Television show
KW - Film design
KW - Project
Y1 - 2004
ER -
TY - GEN
A1 - Rößler, Edith
A1 - Kühn, Nicola
T1 - Murphy's law
N2 - Ein Kurzfilm über den letzten Morgen im Leben eines Mannes, das durch Murphy's Law gekennzeichnet ist
N2 - A short black-and-white film featuring the last morning in a life of a man who happens to obey the rules of Murphy's law.
KW - Mediendesign
KW - Filmregie
KW - Stummfilm
KW - Kurzfilm
KW - Schwarz-Weiß-Film
KW - Regie
KW - Studienprojekt
KW - Grundstudium
KW - Projekt
KW - Black-and-white-film
KW - film directing
KW - Project
Y1 - 2004
ER -
TY - GEN
A1 - Bissels, Anne
A1 - Jahn, Amelie
T1 - Schweinebraten
T1 - Roast pork
N2 - Der Kurzfilm begleitet einen Mann und seine Hündin Gerti auf einem Spaziergang. Die Filmperspektive ist die des Tieres.
N2 - The shortfilm accompanies a man walking his dog Geri. The spectators perspektive is that of the dog.
KW - Kurzfilm
KW - Filmregie
KW - Video
KW - Kamera
KW - Kurzfilm
KW - Handkamera
KW - Videofilm
KW - Regie
KW - Froschperspektive
KW - Shortfilm
KW - Video film
KW - Handheld camera
KW - Worm's-eye view
Y1 - 2004
ER -
TY - RPRT
A1 - Weßling, Matthias
T1 - How to deal with foreign cultures: an cross-cultural training-approach based on the didactical methodology of 'experiential learning' following Kolb & Fry
N2 - Many companies still conduct the worldwide management of people as if neither the external economic nor the internal structure of the firm had changed. The costs of cross-cultural failure, for individuals and their companies, are enormous: personal and family costs; financial, professional and emotional costs; costs to one’s career prospects, to one’s self-esteem, to one’s marriage and family. This scenario describes sufficiently the reason for learning “the art of crossing cultures” (Craig Storti). To this end, this research paper describes an innovative approach of cross-cultural training, following the didactical ideas of Kolb and Fry, the so-called 'experiential learning'.
N2 - Viele international agierende Unternehmen verfahren mit dem weltweiten Personalmanagement so, als wenn sich weder der ökonomische Kontext noch die internen Strukturen der Firmen geändert hätten. Die Kosten von interkulturellen Mißverständnissen und Fehlschlägen sind enorm - sowohl für alle beteiligten Personen, als auch für die betroffenen Unternehmen: hier geht es um berufliche, emotionale, soziale Kosten bis hin zu Beeinträchtigungen der Selbstwertschätzung oder auch der ehelichen Paarbeziehungen. Dieses Szenario beschreibt die Notwendigkeit, sich intensive auseinanderzusetzen mit dem, was Craig Storti "the art of crossing cultures" nennt. Vor diesem Hintergrund beschreibt das vorliegende Forschungspapier einen innovativen Ansatz für ein interkulturelles Managementtraining auf der methodischen Basis der didaktischen Idee des 'experiential learning' nach Kolb und Fry.
KW - Interkulturelles Lernen
KW - Kulturvergleich
KW - Interkulturelles Management
KW - Erfahrungsorientiertes Lernen
KW - Völkerpsychologie
KW - Interkulturelles Training
KW - Managementtraining
KW - Erfahrungslernen
KW - Interkulturelles Lernen
KW - Kulturvergleichende Psychologie
KW - Cross-Cultural Training
KW - Intercultural Awareness
KW - Experiential Learning
KW - Managementtraining
KW - Cross-Cultural Psychology
Y1 - 2009
ER -
TY - CHAP
A1 - Becker, Astrid
T1 - Anlagenmanagement und Aufgaben der DB Netz AG, Bauherrenvertretung und Wirtschaftlichkeit
N2 - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 18 Übersicht des Vortrags
KW - Anlagenwirtschaft
KW - Bauherrenvertretung
KW - Deutsche Bahn Netz AG
Y1 - 2006
ER -
TY - CHAP
A1 - Wellmann, Judith
T1 - Perspektiven eines Bauingenieurs im konstruktiven Ingenieurbau
N2 - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 7-12 Die Berufsperspektiven im konstruktiven Ingenieurbau werden trotz sinkendem Bedarf an Statikern positiv bewertet.
KW - Ingenieurbau
KW - Konstruktiver Ingenieurbau
KW - Statiker
KW - Berufsperspektiven
Y1 - 2006
ER -
TY - CHAP
A1 - Merten, Sabine
A1 - Kämper, Klaus-Peter
A1 - Brill, Manfred
A1 - Picard, Antoni
A1 - Cassel, Detlev
A1 - Jentsch, Andreas
A1 - Rollwa, Markus
T1 - Virtuelle Sensor-Fertigung: Hightech mit LabVIEW
N2 - Eine neue Generation von Praktika an Hochschulen wächst heran. Moderne Wege beim Verstehen und Erlernen naturwissenschaftlicher Zusammenhänge sowie industrieller Fertigungsprozesse sind gefordert. Das Technologiepraktikum „Virtuelle Sensor- Fertigung“, entwickelt im Verbundprojekt INGMEDIA an den Fachhochschulen Aachen und Zweibrücken, trägt als neuartiges Lern- und Lehrmodul dieser Forderung Rechnung. Die Studierenden lernen einen vollständigen Fertigungsprozess mit Hilfe von virtuellen, in LabVIEW programmierten Maschinen kennen, bevor sie die reale Prozesskette im Reinraum durchführen.
N2 - A new generation of university laboratory courses is presently being developed. Modern concepts for the understanding and learning of applied science and industrial fabrication processes are required. The technology course “Fabrication of a microsensor”, developed by the Universities of Applied Sciences Aachen and Zweibrücken in the joint research project INGMEDIA, represents a new approach towards education in high technology production. The students learn the operation of the complex microfabrication line with the help of virtual fabrication machines, programmed in LabVIEW, before they perform the actual process in a genuine clean room.
KW - LabVIEW
KW - Virtuelle Sensor-Fertigung
KW - Fertigungsprozess
KW - virtuelle Maschinen
KW - virtual sensor fabrication
KW - manufacturing process
KW - virtual
KW - virtual machines
Y1 - 2003
ER -
TY - CHAP
A1 - Merten, Sabine
A1 - Kämper, Klaus-Peter
A1 - Brill, Manfred
A1 - Picard, Antoni
A1 - Cassel, Detlev
A1 - Jentsch, Andreas
A1 - Rollwa, Markus
T1 - Vom virtuellen Wafer zum realen Drucksensor
N2 - Das Technologiepraktikum „Virtuelle Sensor-Fertigung“ ist ein Beispiel für die medientechnische Aufbereitung von Lern- und Lehrmaterial unter didaktischen Gesichtspunkten. Studierende lernen einen Fertigungsprozess mit Hilfe von virtuellen Maschinen kennen, bevor sie die reale Prozesskette im Laborpraktikum im Reinraum durchführen.
N2 - The technology course “Fabrication of a microsensor” represents a multimediabased approach towards education in high technology production in consideration of didactical aspects. The students learn the operation of a complex microfabrication line with the help of virtual fabrication machines before they perform the actual process in a hands-on training in an actual clean room.
KW - Virtuelle Maschine
KW - VM
KW - Virtuelle Sensor-Fertigung
KW - virtual fabrication of a microsensor
Y1 - 2003
ER -
TY - JOUR
A1 - Picard, Antoni
A1 - Brill, Manfred
A1 - Cassel, Detlev
A1 - Jentsch, Andreas
A1 - Rollwa, Markus
A1 - Kämper, Klaus-Peter
A1 - Merten, Sabine
T1 - Neue Medien für die praktische MST-Ausbildung
N2 - Im Studiengang Mikrosystemtechnik des Fachhochschulstandortes Zweibrücken werden zwei neue moderne Anlagen für die Herstellung von mikrotechnischen Komponenten in Betrieb genommen: Ein Oxidationsofen für Herstellung dünner Oxidschichten auf Silizium-Einkristallen und eine Belichtungsapparatur für die Fotolithografie - das Besondere an diesen Anlagen: Sie existieren nur virtuell, d.h. als Animationen in einer Computerwelt.
KW - Mikrosystemtechnik
KW - Photolithographie
KW - Mikrotechnik
KW - mikrotechnische Komponenten
KW - Oxidationsofen
KW - Oxidschicht
KW - multimediale Lernsoftware
KW - micro technology
KW - micro-technical components
KW - oxidation furnace
KW - oxide coating
Y1 - 2002
ER -
TY - JOUR
A1 - Kämper, Klaus-Peter
A1 - Picard, Antoni
A1 - Brill, Manfred
A1 - Cassel, Detlev
A1 - Jentsch, Andreas
A1 - Merten, Sabine
A1 - Rollwa, Markus
T1 - The Virtual Clean Room - a new tool in teaching MST process technologies
N2 - The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room.
KW - Virtuelle Maschine
KW - VM
KW - Mikrosystemtechnik
KW - MST
KW - virtual clean room
Y1 - 2003
ER -
TY - GEN
A1 - Bellenberg, Markus
T1 - Optimierung einer Roboter-Schweißzelle als Basis eines E-Learning Systems
T1 - Optimization of a Robot-welding Station as the Basis for an E-Learning System
N2 - Ziel war die technische Überarbeitung und Optimierung des vorliegenden Prototypen, um eine Basis für ein E-Learning System (Internet unterstütztes Lernen) zu schaffen. Zu diesem Zweck wurde das Programm der Robotersteuerung neu erstellt, notwendige mechanische Änderungen an Roboterequipment und Materialförderung vorgenommen sowie eine neue Internet-Anbindung geschaffen. Wesentliche Ergebnisse der Arbeit sind: • Erzeugen roboterbasierter kreisinterpolierter Bahnschweißnähte • Kommunikation des Lernsystems via Internet • Lernorientierte Steuerungssoftware
N2 - The main goal of this final thesis was the revision and optimization of the given prototype as a basis for an E-Learning environment. All components of the system, including specific technical aspects, are discussed in order to create the basis for future training documentation. Similarly, the programs for the robot motion sequences and welding processes were renewed in order to create well-structured, clear and properly documented software that is suitable for use in a formal training program.
KW - Roboter
KW - MAG-Schweißen
KW - MIG-Schweißen
KW - Schweißen
KW - Mechatronik
KW - Kawasaki
KW - E-Learning
KW - Roboter-Schweißen
KW - welding
KW - welded joint
KW - mechatronics
Y1 - 2002
ER -
TY - GEN
A1 - Balzar, Christoph Rupert
T1 - Land in land
N2 - [...] Darin suche ich „Zwischenräume“ in der digitalen Verschmelzung von Fotos unterschiedlicher Orte und durchleuchte diese neu geschaffenen Landschaften auf ihren Sinn für mich. Anhand der so ge-wonnenen Erkenntnisse belebe ich diese Plätze später mit Menschen, Tieren und Fundstücken, die mir das Schicksal auf meinen „Walkabouts“ durch den australischen Kontinent zugespielt hat und denen ich zu den neu entstandenen Orten passende Bedeutungen beimesse. [...] Neben meinen flächigen, fotografischen und installativen Werken stelle ich auch ein umfassendes Rahmen- und Begleitprogramm zur Ausstellung her, beispielsweise eine CI und eine Homepage.
KW - Digitale Photographie
KW - Photomontage
KW - Naturphotographie
KW - Aborigines
KW - Fotografie
KW - Digitale Montage
KW - Bilderserie
KW - Ureinwohner
KW - Australien
KW - Inszenierte Photographie
KW - Photography
KW - Digital montage
KW - Series
KW - Aboriginal people
KW - Australia
KW - Set-up photography
Y1 - 2005
ER -
TY - GEN
A1 - Samm, Doris
A1 - Meurer, Marcel
T1 - Die elektrische Leitung und Supraleitung
N2 - Die Lerneinheit stellt in anschaulicher Weise die verschiedenen Modelle der elektrischen Leitung dar und führt über diese zur Erklärung der Supraleitung. Effekte und Anwendungen der Supraleitung werden in Animationen und Bildern vorgeführt. Ein umfangreiches Glossar erläutert wichtige Begriffe.
KW - Elektrische Leitung
KW - Supraleitung
KW - Elektronengas
KW - Bändermodell
KW - Festkörper
KW - Elektrische Leitung
KW - Supraleitung
Y1 - 2003
ER -
TY - GEN
A1 - Samm, Doris
A1 - Perteck, Patrik
T1 - Der Helium-Neon-Laser
N2 - In der Lerneinheit werden zunächst anschaulich die Eigenschaften verschiedener Lichtquellen sowie wichtige Begriffe erläutert. Anschließen wird das physikalische Prinzip des HeNe-Lasers erklärt. Die Lerneinheit endet mit der Beschreibung des technischen Aufbaus eines HeNe-Lasers.
KW - Helium-Neon-Laser
KW - Lichtquelle
KW - Lichtabsorption
KW - Lichtemission
KW - Resonator
KW - Simulation
KW - Virtuelle Realität
KW - Lichtbetrachtung
KW - Besetzungsinversion
KW - He-Ne Laser
KW - He-Ne Schema
Y1 - 2003
ER -
TY - GEN
A1 - Samm, Doris
T1 - Mathematisches Pendel (Simulation in Java)
N2 - Die Anwender können die Länge des Pendels und die Auslenkung einstellen. Es werden die Änderung der potentiellen und kinetischen Energie sowie des Auslenkwinkels als Funktion der Zeit dargestellt.
KW - Pendel
KW - Auslenkung
KW - Javasimulation
Y1 - 2003
ER -
TY - JOUR
T1 - Fachblatt, Jahrgang 2005; Nr. 2
N2 - Institute 20 Jahre "Summer School Renewable Energy" Personen Prof. Dr.rer.nat. Dr.h.c. Gisela Engeln-Müllges geht in den Ruhestand Fachhochschul-Rektor Prof. Hermann-Josef Buchkremer geht in den Ruhestand Forschung "Badekultur in der Renaissance" Studenten an der Fachhochschule bauen Mini-Satellit Service Start von Cmpus, HIS QIS und neuem Webdesign "Join the best" - MLP bietet neue Chancen auf internationale Spitzenpraktika Forschungsergebnisse werden weltweit sichtbar Menschen an der FH Ein Bild entsteht zuerst im Kopf - die Diplom-Fotografin Jeanne Püttmann FH Aachen als Sprungbrett in luftige Höhen - Silke Lotties Auch mit 100 noch Flugbenzin im Blut! - Aachener Flugpionier Richard Perlia Zwischen Marathon und Studium - Angela Müller Einer der ersten Absolventen des Masterstudiengangs Facility Management - Mike Müller Aus den Fachbereichen Naturwissenschaften zum Anfassen: Lehrer zeigen hohe Motivation DIPLOMA 2005 - Derspringendepunkt Neue "Welten" erleben - Studierende beginnen ihren Auslandsaufenthalt Endlich der Sieg: Bauingenieure erfolgreich in der Wertung Bootskonstruktion Viele Fragen werden am Info-Tag Wirtschaftswissenschaften beantwortet Alumni Erster "Luft- und Raumfahrt" - Absolventenkongress Ein halbes Jahrhundert Bauingenieure Personalinfo Honorarprofessor Dr. Peter Lelkes Prof. Dr.-Ing. Günther Dahl Prof. Klaus Endrikat Prof. Dr.-Ing. Alexander Boeminghaus Prof. Dr. Narendra Bansal jetzt Rektor in Indien
T3 - Fachblatt / FH Aachen - 2005, 2
KW - Fachhochschule Aachen
KW - Fachhochschule Aachen
KW - Aachen University of Applied Sciences
Y1 - 2005
ER -
TY - GEN
A1 - Horsch, Andreas
T1 - Die Masken des Harlekin : Formensprache im Charakterdesign
T1 - The harlequin's masks : formal language in character design
N2 - Ziel und Inhalt dieser Arbeit ist das Design eines Harlekin-Charakters und die Darstellung seiner Ausdrucksskala. Der Schwerpunkt liegt dabei auf dem Studium der Gesichtsmuskeln, ihrer Formensprache und ihrer Relation zu den 6 Grundemotionen Traurigkeit, Ärger, Angst, Freude, Ekel und Überraschung (nach dem Modell von Paul Ekman). Alle 6 Emotionen sind in verschiedenen Intensitätsgraden und Variationen behandelt, wobei die Emotion der Freude aufgrund ihrer engen Bindung zum Harlekin-Charakter vergleichsweise umfassender bearbeitet wurde. Das Endergebnis stellt eine Bildreihe von ca. 50 Ausdrücken und eine Abhandlung über Gesichtsmuskulatur und -ausdruck, dessen Relation zu den Emotionen und den Hintergrund des Harlekincharakters dar. Die Illustrationen wurden unter Verwendung der 3D-Technologie von Maya 7.0 und ZBrush 2.0 ausgeführt.
N2 - The content and goal of this work is the design of a harlequin-character and the depiction of his range of expression. The focal point lies on the study of the facial muscles, their formal vocabulary and their relation to the 6 basic emotions sadness, anger, fear, joy, disgust and surprise (after Paul Ekman's model). All 6 emotions are treated in different intensities and variations, whereas the emotion of joy is handled in a more profound way because of its close relationship to the harlequin-character. The end result is a series of illustrations of approx. 50 expressions and a treatise on the topic of facial musculature and expression, their relationship to emotions and the background of the harlequin-character. The illustrations were realized using the 3D-technologies of Maya 7.0 and ZBrush 2.0.
KW - Harlekin
KW - Gesichtsmuskel
KW - Mimik
KW - Modellierung
KW - Gefühl
KW - 3D
KW - Charakter
KW - Drahtgittermodell
KW - Gesichtsmodellierung
KW - Gesichtsausdruck
KW - 3D
KW - character
KW - facial expression
KW - facial modeling
KW - wire frame model
Y1 - 2006
ER -
TY - JOUR
A1 - Weßling, Matthias
T1 - Aktives Nachfolger-Coaching für den Mittelstand setzt früh an : innovative Idee für Studierende der FH Aachen
N2 - Es gibt oft Schwierigkeiten in der Unternehmernachfolge wegen fehlender Beratung. Die FH Aachen bietet ihren Studierenden seit 2007 ein Coaching an.
KW - Unternehmernachfolge
KW - Coaching
Y1 - 2008
ER -
TY - CHAP
A1 - Wagner, Torsten
A1 - Schöning, Michael Josef
T1 - Preface of the Special Issue of I3S 2005 in Jülich (Germany)
N2 - International Symposium on Sensor Science, I3S 2005 <3; 2005; Juelich, Germany> In: Sensors 2006, 6, 260-261 ISSN 1424-8220
KW - Biosensor
KW - I3S 2005
KW - International Symposium on Sensor Science
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1365
ER -
TY - CHAP
A1 - Srivastava, Alok
A1 - Singh, Virendra
A1 - Dhand, Chetna
A1 - Kaur, Manindar
A1 - Singh, Tejvir
A1 - Witte, Katrin
A1 - Scherer, Ulrich W.
T1 - Study of swift heavy ion modified conduction polymer composites for application as gas sensor
N2 - A polyaniline-based conducting composite was prepared by oxidative polymerisation of aniline in a polyvinylchloride (PVC) matrix. The coherent free standing thin films of the composite were prepared by a solution casting method. The polyvinyl chloride-polyaniline composites exposed to 120 MeV ions of silicon with total ion fluence ranging from 1011 to 1013 ions/cm2, were observed to be more sensitive towards ammonia gas than the unirradiated composite. The response time of the irradiated composites was observed to be comparably shorter. We report for the first time the application of swift heavy ion modified insulating polymer conducting polymer (IPCP) composites for sensing of ammonia gas.
KW - Biosensor
KW - Conducing polymer
KW - ammonia gas sensors
KW - swift heavy ions
KW - polymer composites
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1345
ER -
TY - CHAP
A1 - Chaiyboun, Ali
A1 - Traute, Rüdiger
A1 - Kiesewetter, Olaf
A1 - Ahlers, Simon
A1 - Müller, Gerhard
A1 - Doll, Theodor
T1 - Modular analytical multicomponent analysis in gas sensor arrays
N2 - A multi-sensor system is a chemical sensor system which quantitatively and qualitatively records gases with a combination of cross-sensitive gas sensor arrays and pattern recognition software. This paper addresses the issue of data analysis for identification of gases in a gas sensor array. We introduce a software tool for gas sensor array configuration and simulation. It concerns thereby about a modular software package for the acquisition of data of different sensors. A signal evaluation algorithm referred to as matrix method was used specifically for the software tool. This matrix method computes the gas concentrations from the signals of a sensor array. The software tool was used for the simulation of an array of five sensors to determine gas concentration of CH4, NH3, H2, CO and C2H5OH. The results of the present simulated sensor array indicate that the software tool is capable of the following: (a) identify a gas independently of its concentration; (b) estimate the concentration of the gas, even if the system was not previously exposed to this concentration; (c) tell when a gas concentration exceeds a certain value. A gas sensor data base was build for the configuration of the software. With the data base one can create, generate and manage scenarios and source files for the simulation. With the gas sensor data base and the simulation software an on-line Web-based version was developed, with which the user can configure and simulate sensor arrays on-line.
KW - Biosensor
KW - Main sensitivity
KW - cross sensitivity
KW - matrix method
KW - gas sensor array
KW - modelling
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1358
ER -
TY - CHAP
A1 - Sakthivel, Mariappan
A1 - Weppner, Werner
T1 - Response behaviour of a hydrogen sensor based on ionic conducting polymer-metal interfaces prepared by the chemical reduction method
N2 - A solid-state amperometric hydrogen sensor based on a protonated Nafion membrane and catalytic active electrode operating at room temperature was fabricated and tested. Ionic conducting polymer-metal electrode interfaces were prepared chemically by using the impregnation-reduction method. The polymer membrane was impregnated with tetra-ammine platinum chloride hydrate and the metal ions were subsequently reduced by using either sodium tetrahydroborate or potassium tetrahydroborate. The hydrogen sensing characteristics with air as reference gas is reported. The sensors were capable of detecting hydrogen concentrations from 10 ppm to 10% in nitrogen. The response time was in the range of 10-30 s and a stable linear current output was observed. The thin Pt films were characterized by XRD, Infrared Spectroscopy, Optical Microscopy, Atomic Force Microscopy, Scanning Electron Microscopy and EDAX.
KW - Biosensor
KW - Hydrogen sensor
KW - amperometric sensor
KW - porous Pt electrode
KW - chemical reduction method
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1399
ER -
TY - CHAP
A1 - Koplin, Tobias J.
A1 - Siemons, Maike
A1 - Océn-Valéntin, César
A1 - Sanders, Daniel
A1 - Simon, Ulrich
T1 - Workflow for high throughput screening of gas sensing materials
N2 - The workflow of a high throughput screening setup for the rapid identification of new and improved sensor materials is presented. The polyol method was applied to prepare nanoparticular metal oxides as base materials, which were functionalised by surface doping. Using multi-electrode substrates and high throughput impedance spectroscopy (HT-IS) a wide range of materials could be screened in a short time. Applying HT-IS in search of new selective gas sensing materials a NO2-tolerant NO sensing material with reduced sensitivities towards other test gases was identified based on iridium doped zinc oxide. Analogous behaviour was observed for iridium doped indium oxide.
KW - Biosensor
KW - High throughput experimentation
KW - gas sensor
KW - metal oxide
KW - doping
KW - impedance spectroscopy
KW - nitrogen oxides
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1407
ER -
TY - CHAP
A1 - Spannhake, Jan
A1 - Schulz, Olaf
A1 - Helwig, Andreas
A1 - Krenkow, Angelika
A1 - Müller, Gerhard
A1 - Doll, Theodor
T1 - High-temperature MEMS heater platforms: long-term performance of metal and semiconductor heater materials
N2 - Micromachined thermal heater platforms offer low electrical power consumption and high modulation speed, i.e. properties which are advantageous for realizing nondispersive infrared (NDIR) gas- and liquid monitoring systems. In this paper, we report on investigations on silicon-on-insulator (SOI) based infrared (IR) emitter devices heated by employing different kinds of metallic and semiconductor heater materials. Our results clearly reveal the superior high-temperature performance of semiconductor over metallic heater materials. Long-term stable emitter operation in the vicinity of 1300 K could be attained using heavily antimony-doped tin dioxide (SnO2:Sb) heater elements.
KW - Biosensor
KW - Hotplate
KW - heater metallisation
KW - high-temperature stability
KW - electro-migration
KW - doped silicon
KW - doped metal oxide
KW - antimony doped tin oxide
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1513
ER -
TY - CHAP
A1 - Katz, Eugenii
A1 - Willner, Itamar
T1 - Magneto-controlled quantized electron transfer to surface-confined redox units and metal nanoparticles
N2 - Hydrophobic magnetic nanoparticles (NPs) consisting of undecanoate-capped magnetite (Fe3O4, average diameter ca. 5 nm) are used to control quantized electron transfer to surface-confined redox units and metal NPs. A two-phase system consisting of an aqueous electrolyte solution and a toluene phase that includes the suspended undecanoatecapped magnetic NPs is used to control the interfacial properties of the electrode surface. The attracted magnetic NPs form a hydrophobic layer on the electrode surface resulting in the change of the mechanisms of the surface-confined electrochemical processes. A quinone-monolayer modified Au electrode demonstrates an aqueous-type of the electrochemical process (2e-+2H+ redox mechanism) for the quinone units in the absence of the hydrophobic magnetic NPs, while the attraction of the magnetic NPs to the surface results in the stepwise single-electron transfer mechanism characteristic of a dry nonaqueous medium. Also, the attraction of the hydrophobic magnetic NPs to the Au electrode surface modified with Au NPs (ca. 1.4 nm) yields a microenvironment with a low dielectric constant that results in the single-electron quantum charging of the Au NPs.
KW - Biosensor
KW - Nanoparticles
KW - magnetic particles
KW - quantum charging
KW - modified electrode
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1528
ER -
TY - CHAP
A1 - Pijanowska, Dorota G.
A1 - Remiszewska, Elzbieta
T1 - pH-based detection of phenylalnine by potentiometric and colorimetric methods
N2 - In this paper, methods of sample preparation for potentiometric measurement of phenylalanine are presented. Basing on the spectrophotometric measurements of phenylalanine, the concentrations of reagents of the enzymatic reaction (10 mM L-Phe, 0,4 mM NAD+, 2U L-PheDH) were determined. Then, the absorption spectrum of the reaction product, NADH, was monitored (maximum peak at 340 nm). The results obtained by the spectrophotometric method were compared with the results obtained by the colourimetry, using pH indicators. The above-mentioned two methods will be used as references for potentiometric measurements of phenylalanine concentration.
KW - Biosensor
KW - Phenylalanine determination
KW - enzymatic methods
KW - pH-based biosensing
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1536
ER -
TY - CHAP
A1 - Arida, Hassan A.
A1 - Kloock, Joachim P.
A1 - Schöning, Michael Josef
T1 - Novel organic membrane-based thin-film microsensors for the determination of heavy metal cations
N2 - A first step towards the fabrication and electrochemical evaluation of thin-film microsensors based on organic PVC membranes for the determination of Hg(II), Cd(II), Pb(II) and Cu(II) ions in solutions has been realised. The membrane-coating mixture used in the preparation of this new type of microsensors is incorporating PVC as supporting matrix, o-nitrophenyloctylether (o-NPOE) as solvent mediator and a recently synthesized Hg[dimethylglyoxime(phene)]2+ and Bis-(4-hydroxyacetophenone)-ethylenediamine as electroactive materials for Hg(II) and Cd(II), respectively. A set of three commercialised ionophores for Cd(II), Pb(II) and Cu(II) has been also used for comparison. Thin-film microsensors based on these membranes showed a Nernstian response of slope (26-30 mV/dec.) for the respective tested cations. The potentiometric response characteristics (linear range, pH range, detection limit and response time) are comparable with those obtained by conventional membranes as well as coated wire electrodes prepared from the same membrane. The realisation of the new organic membrane-based thin-film microsensors overcomes the problem of an insufficient selectivity of solid-state-based thinfilm sensors.
KW - Biosensor
KW - Heavy metal detection
KW - thin-film microsensors
KW - organic PVC membranes
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1545
ER -
TY - CHAP
A1 - Barek, Jiri
A1 - Fischer, Jan
A1 - Navratil, Tomas
A1 - Peckova, Karolina
A1 - Yosypchuk, Bogdan
T1 - Silver solid amalgam electrodes as sensors for chemical carcinogens
N2 - The applicability of differential pulse voltammetry (DPV) and adsorptive stripping voltammetry (AdSV) at a non-toxic meniscus-modified silver solid amalgam electrode (m-AgSAE) for the determination of trace amounts of genotoxic substances was demonstrated on the determination of micromolar and submicromolar concentrations of 3-nitrofluoranthene using methanol - 0.01 mol L-1 NaOH (9:1) mixture as a base electrolyte and of Ostazine Orange using 0.01 mol L-1 NaOH as a base electrolyte.
KW - Biosensor
KW - Solid amalgam electrodes
KW - voltammetry
KW - carcinogens
KW - 3-nitrofluoranthene
KW - Ostazine Orange
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1554
ER -
TY - CHAP
A1 - Baronas, Romas
A1 - Ivanauskas, Feliksas
A1 - Kulys, Juozas
T1 - Mathematical modeling of biosensors based on an array of enzyme microreactors
N2 - This paper presents a two-dimensional-in-space mathematical model of biosensors based on an array of enzyme microreactors immobilised on a single electrode. The modeling system acts under amperometric conditions. The microreactors were modeled by particles and by strips. The model is based on the diffusion equations containing a nonlinear term related to the Michaelis-Menten kinetics of the enzymatic reaction. The model involves three regions: an array of enzyme microreactors where enzyme reaction as well as mass transport by diffusion takes place, a diffusion limiting region where only the diffusion takes place, and a convective region, where the analyte concentration is maintained constant. Using computer simulation, the influence of the geometry of the microreactors and of the diffusion region on the biosensor response was investigated. The digital simulation was carried out using the finite difference technique.
KW - Biosensor
KW - Reaction-diffusion
KW - modeling biosensor
KW - microreactor
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1569
ER -
TY - CHAP
A1 - Lei, Yu
A1 - Mulchandani, Priti
A1 - Chen, Wilfred
A1 - Mulchandani, Ashok
T1 - Biosensor for direct determination of fenitrothion and EPN using recombinant Pseudomonas putida JS444 with surface expressed organophosphorus hydrolase. 1. modified clark oxygen electrode
N2 - This paper reports a first microbial biosensor for rapid and cost-effective determination of organophosphorus pesticides fenitrothion and EPN. The biosensor consisted of recombinant PNP-degrading/oxidizing bacteria Pseudomonas putida JS444 anchoring and displaying organophosphorus hydrolase (OPH) on its cell surface as biological sensing element and a dissolved oxygen electrode as the transducer. Surfaceexpressed OPH catalyzed the hydrolysis of fenitrothion and EPN to release 3-methyl-4-nitrophenol and p-nitrophenol, respectively, which were oxidized by the enzymatic machinery of Pseudomonas putida JS444 to carbon dioxide while consuming oxygen, which was measured and correlated to the concentration of organophosphates. Under the optimum operating conditions, the biosensor was able to measure as low as 277 ppb of fenitrothion and 1.6 ppm of EPN without interference from phenolic compounds and other commonly used pesticides such as carbamate pesticides, triazine herbicides and organophosphate pesticides without nitrophenyl substituent. The applicability of the biosensor to lake water was also demonstrated.
KW - Biosensor
KW - Organophosphorus
KW - fenitrothion
KW - EPN
KW - biosensor
KW - Pseudomonas putida
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1573
ER -
TY - JOUR
A1 - Matheis, Anton
A1 - Röth, Thilo
A1 - Wagner, Manfred
T1 - Studentenprojekt "Capro" – eine virtuelle Sportwagenstudie "Vision 2015"
N2 - Design- und Karosseriebaustudenten der FH Aachen entwickeln gemeinsam mit externen Fachleuten unter Einsatz virtueller Entwicklungswerkzeuge ein Konzept für einen Sportwagen
KW - Karosseriebau
KW - Sportwagen
KW - Kraftfahrzeugbau
KW - Studentenprojekt
KW - Virtuelle Fahrzeugentwicklung
KW - car body construction
Y1 - 2005
ER -
TY - GEN
A1 - Röth, Thilo
T1 - Leichtbau und Karosserietechnik
T1 - Light weight structures and body engineering
N2 - Studienschwerpunkt Leichtbau und Karosserietechnik an der FH Aachen, Grobstruktur der Lehrinhalte, Studentenprojekt "CAPRO"
KW - Leichtbau
KW - Karosseriebau
KW - Karosserietechnik
KW - car body construction
Y1 - 2004
ER -
TY - JOUR
A1 - Dick, Angela
A1 - Wagner, Manfred
A1 - Röth, Thilo
T1 - Capro Automotive Group FH Aachen
N2 - Design- und Karosseriebaustudenten der FH Aachen entwickeln gemeinsam mit externen Fachleuten unter Einsatz virtueller Entwicklungswerkzeuge ein Konzept für einen Sportwagen
KW - Karosseriebau
KW - Sportwagen
KW - Kraftfahrzeugbau
KW - Studentenprojekt
KW - Virtuelle Fahrzeugentwicklung
KW - car body construction
Y1 - 2005
ER -
TY - CHAP
A1 - Näther, Niko
A1 - Juárez, Leon M.
A1 - Emmerich, Rüdiger
A1 - Berger, Jörg
A1 - Friedrich, Peter
A1 - Schöning, Michael Josef
T1 - Detection of hydrogen peroxide (H2O2) at exposed temperatures for industrial processes
N2 - An H2O2 sensor for the application in industrial sterilisation processes has been developed. Therefore, automated sterilisation equipment at laboratory scale has been constructed using parts from industrial sterilisation facilities. In addition, a software tool has been developed for the control of the sterilisation equipment at laboratory scale. First measurements with the developed sensor set-up as part of the sterilisation equipment have been performed and the sensor has been physically characterised by optical microscopy and SEM.
KW - Biosensor
KW - Gas sensor
KW - hydrogen peroxide
KW - sterilisation
KW - catalytic decomposition
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1418
ER -
TY - CHAP
A1 - Wagner, Thorsten
A1 - Kohl, Claus-Dieter
A1 - Fröba, Michael
A1 - Tiemann, Michael
T1 - Gas sensing properties of ordered mesoporous SnO2
N2 - We report on the synthesis and CO gas-sensing properties of mesoporous tin(IV) oxides (SnO2). For the synthesis cetyltrimethylammonium bromide (CTABr) was used as a structure-directing agent; the resulting SnO2 powders were applied as films to commercially available sensor substrates by drop coating. Nitrogen physisorption shows specific surface areas up to 160 m2·g-1 and mean pore diameters of about 4 nm, as verified by TEM. The film conductance was measured in dependence on the CO concentration in humid synthetic air at a constant temperature of 300 °C. The sensors show a high sensitivity at low CO concentrations and turn out to be largely insensitive towards changes in the relative humidity. We compare the materials with commercially available SnO2-based sensors.
KW - Biosensor
KW - Tin oxide
KW - sensing properties
KW - CO
KW - humidity
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1422
ER -
TY - CHAP
A1 - Mirmohseni, Abdolreza
A1 - Rostamizadeh, Kobra
T1 - Quartz crystal nanobalance in conjunction with principal component analysis for identification of volatile organic compounds
N2 - Quartz crystal nanobalance (QCN) sensors are considered as powerful masssensitive sensors to determine materials in the sub-nanogram level. In this study, a single piezoelectric quartz crystal nanobalance modified with polystyrene was employed to detect benzene, toluene, ethylbenzene and xylene (BTEX compounds). The frequency shift of the QCN sensor was found to be linear against the BTEX compound concentrations in the range about 1-45 mg l-1. The correlation coefficients for benzene, toluene, ethylbenzene, and xylene were 0.991, 0.9977, 0.9946 and 0.9971, respectively. The principal component analysis was also utilized to process the frequency response data of the single piezoelectric crystal at different times, considering to the different adsorption-desorption dynamics of BTEX compounds. Using principal component analysis, it was found that over 90% of the data variance could still be explained by use of two principal components (PC1 and PC2). Subsequently, the successful identification of benzene and toluene was possible through the principal component analysis of the transient responses of the polystyrene modified QCN sensor. The results showed that the polystyrene-modified QCN had favorable identification and quantification performances for the BTEX compounds.
KW - Biosensor
KW - Quartz crystal nanobalance (QCN)
KW - BTEX compounds
KW - principal component
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1434
ER -
TY - CHAP
A1 - Kreutz, Christian
A1 - Lörgen, Jürgen
A1 - Graewe, Boris
A1 - Bargon, Joachim
A1 - Yoshida, Mayumi
A1 - Freso, Zachary M.
A1 - Frèchet, Jean M. J.
T1 - High frequency quartz micro balances: a promising path to enhanced sensitivity of gravimetric sensors
N2 - An array of 50 MHz quartz microbalances (QMBs) coated with a dendronized polymer was used to detect small amounts of volatile organic compounds (VOCs) in the gas phase. The results were compared to those obtained with the commonly used 10 MHz QMBs. The 50 MHz QMBs proved to be a powerful tool for the detection of VOCs in the gas phase; therefore, they represent a promising alternative to the much more delicate surface acoustic wave devices (SAWs).
KW - Biosensor
KW - Quartz micro balances
KW - electronic noses dendronized polymers inverted mesa technology
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1445
ER -
TY - CHAP
A1 - Rabner, Arthur
A1 - Shacham, Yosi
T1 - A concept for a sensitive micro total analysis system for high throughput fluorescence imaging
N2 - This paper discusses possible methods for on-chip fluorescent imaging for integrated bio-sensors. The integration of optical and electro-optical accessories, according to suggested methods, can improve the performance of fluorescence imaging. It can boost the signal to background ratio by a few orders of magnitudes in comparison to conventional discrete setups. The methods that are present in this paper are oriented towards building reproducible arrays for high-throughput micro total analysis systems (µTAS). The first method relates to side illumination of the fluorescent material placed into microcompartments of the lab-on-chip. Its significance is in high utilization of excitation energy for low concentration of fluorescent material. The utilization of a transparent µLED chip, for the second method, allows the placement of the excitation light sources on the same optical axis with emission detector, such that the excitation and emission rays are directed controversly. The third method presents a spatial filtering of the excitation background.
KW - Biosensor
KW - Fluorescence
KW - imaging
KW - lab-on-chip
KW - fluidic
KW - lenslet array
KW - LED chip
KW - image sensor
KW - biosensor
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1456
ER -
TY - CHAP
A1 - Förster, Arnold
A1 - Stock, Jürgen
A1 - Montanari, Simone
A1 - Lepsa, Mihail Ion
A1 - Lüth, Hans
T1 - Fabrication and characterisation of GaAs Gunn Diode Chips for applications at 77 GHz in automotive industry
N2 - GaAs-based Gunn diodes with graded AlGaAs hot electron injector heterostructures have been developed under the special needs in automotive applications. The fabrication of the Gunn diode chips was based on total substrate removal and processing of integrated Au heat sinks. Especially, the thermal and RF behavior of the diodes have been analyzed by DC, impedance and S-parameter measurements. The electrical investigations have revealed the functionality of the hot electron injector. An optimized layer structure could fulfill the requirements in adaptive cruise control (ACC) systems at 77 GHz with typical output power between 50 and 90 mW.
KW - Biosensor
KW - Gunn diode
KW - microwave generation
KW - GaAs hot electron injector
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1462
ER -
TY - CHAP
A1 - Pijanowska, Dorota G.
A1 - Remiszewska, Elzbieta
A1 - Pederzolli, Cecilia
A1 - Lunelli, Lorenzo
A1 - Vendano, Michele
A1 - Canteri, Roberto
A1 - Dudzinski, Konrad
A1 - Kruk, Jerzy
A1 - Torbicz, Wladyslaw
T1 - Surface modification for microreactor fabrication
N2 - In this paper, methods of surface modification of different supports, i.e. glass and polymeric beads for enzyme immobilisation are described. The developed method of enzyme immobilisation is based on Schiff’s base formation between the amino groups on the enzyme surface and the aldehyde groups on the chemically modified surface of the supports. The surface of silicon modified by APTS and GOPS with immobilised enzyme was characterised by atomic force microscopy (AFM), time-of-flight secondary ion mass spectroscopy (ToF-SIMS) and infrared spectroscopy (FTIR). The supports with immobilised enzyme (urease) were also tested in combination with microreactors fabricated in silicon and Perspex, operating in a flow-through system. For microreactors filled with urease immobilised on glass beads (Sigma) and on polymeric beads (PAN), a very high and stable signal (pH change) was obtained. The developed method of urease immobilisation can be stated to be very effective.
KW - Biosensor
KW - Microreactors
KW - surface modification
KW - enzyme immobilisation
KW - lab-on-a-chip
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1480
ER -
TY - CHAP
A1 - Bukhari, Syed Faisal Ahmed
A1 - Yang, Wuqiang
T1 - Multi-interface level sensors and new development in monitoring and control of oil separators
N2 - In the oil industry, huge saving may be made if suitable multi-interface level measurement systems are employed for effectively monitoring crude oil separators and efficient control of their operation. A number of techniques, e.g. externally mounted displacers, differential pressure transmitters and capacitance rod devices, have been developed to measure the separation process with gas, oil, water and other components. Because of the unavailability of suitable multi-interface level measurement systems, oil separators are currently operated by the trial-and-error approach. In this paper some conventional techniques, which have been used for level measurement in industry, and new development are discussed.
KW - Biosensor
KW - Level sensor
KW - multi-interface measurement
KW - electrical capacitance tomography
KW - ECT
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1498
ER -
TY - CHAP
A1 - Tymecki, Lukasz
A1 - Glab, Stanislaw
A1 - Koncki, Robert
T1 - Miniaturized, planar ion-selective electrodes fabricated by means of thick-film technology
N2 - Various planar technologies are employed for developing solid-state sensors having low cost, small size and high reproducibility; thin- and thick-film technologies are most suitable for such productions. Screen-printing is especially suitable due to its simplicity, low-cost, high reproducibility and efficiency in large-scale production. This technology enables the deposition of a thick layer and allows precise pattern control. Moreover, this is a highly economic technology, saving large amounts of the used inks. In the course of repetitions of the film-deposition procedure there is no waste of material due to additivity of this thick-film technology. Finally, the thick films can be easily and quickly deposited on inexpensive substrates. In this contribution, thick-film ion-selective electrodes based on ionophores as well as crystalline ion-selective materials dedicated for potentiometric measurements are demonstrated. Analytical parameters of these sensors are comparable with those reported for conventional potentiometric electrodes. All mentioned thick-film strip electrodes have been totally fabricated in only one, fully automated thickfilm technology, without any additional manual, chemical or electrochemical steps. In all cases simple, inexpensive, commercially available materials, i.e. flexible, plastic substrates and easily cured polymer-based pastes were used.
KW - Biosensor
KW - Potentiometry
KW - thick-film technology
KW - screen-printing
KW - ion-selective electrodes
Y1 - 2006
U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1506
ER -
TY - CHAP
A1 - Röth, Thilo
T1 - Modularisierung in der Karosserie von morgen
N2 - 1) Module werden die Fahrzeugplattform und den –aufbau in Zukunft weiterhin und in zunehmendem Maße bestimmen. 2) Neue Module und Modulschnittstellen am Fahrzeug werden überdacht und können in der Zukunft erwartet werden. 3) Die Wertschöpfung und der Entwicklungsumfang wird sich vom OEM zum Modullieferanten verlagern. 4) Modulvergaben werden in der Zukunft noch stärker auf Innovation und Kostenreduktion beruhen. 5) Modularisierung des Fahrzeuges heißt ein Aufbrechen der Fahrzeugkarosserie und wird daher von der Beherrschung struktureller Aufgaben sowie der Lösung der (sichtbaren) Modulübergänge bestimmt sein. 6) Neben den Systemintegratoren und den Komponentenspezialisten besetzen die Modullieferanten die erste Lieferantenriege. 7) Der Modullieferant wird neben höchster Fertigungsexpertise ein hohes Maß an (Teil-)fahrzeug-Know-How und Produktentwickler-mentalität bereitstellen.
KW - Karosseriebau
KW - Karosseriebau
KW - car body construction
Y1 - 2002
ER -
TY - CHAP
A1 - Röth, Thilo
A1 - Tragsdorf, Carsten
T1 - Innovativer Einsatz von Werkstoffen - Trends und Entwicklungen im Karosserieleichtbau
N2 - 1) In Karosseriestrukturen steht der richtige Werkstoffeinsatz stärker den je im Spannungsfeld von Leichtbau, Kosten (Stückzahlen) und Leistungsanforderung 2) In „klassischen“ Strukturen von Modulträgern und Klappen hat sich die Materialmischbauweise verstärkt in den letzten Jahren durchgesetzt 3) Unter Aspekten des konzeptionellen Leichtbaus erscheint der verstärkte Einsatz von Leichtbauwerkstoffen im Vorderwagen sowie in der Dachstruktur zielführend 4) Offene Strukturprofile in Materialmischbauweise liefern für eine Vielzahl von Anwendungen ein interessantes und bis dato kaum genutztes Potential 5) Neue Entwicklungen bei den Fügetechnologien (i.b. kontinuierliche Fügeverbindungen und kombinierte Verfahren) unterstützen den wirtschaftlichen Karosserieleichtbau 6) Werkstoffinnovationen sowie neuartige Fertigungsverfahren machen den Konstruktionswerkstoff „Stahl“ auch in der Zukunft im Karosseriebau weiterhin sehr attraktiv
KW - Karosseriebau
KW - Leichtbau
KW - Karosserieleichtbau
KW - Materialmischbauweise
KW - Leichtbauwerkstoffe
Y1 - 2004
ER -
TY - GEN
A1 - Höttges, Jörg
A1 - Cordes, Jürgen
A1 - Wirtz, Dominika
A1 - Moers, Monika
A1 - Gehlen, Tanja
A1 - Aldenhoven, Frederick
T1 - E-Learning AutoCAD
N2 - Schrittweise Einführung in die Welt des AutoCAD. Nach jedem Abschnitt besteht die Möglichkeit, das neue Wissen direkt anzuwenden. Mit Wissensprüfungen und Übungen nach jedem Kapitel. (Modul wird noch überarbeitet) 1. Der Anfang mit AutoCAD 2. Grundlagen zur Anfertigung einer Zeichnung 3. Layer 4. Texte und Bemaßung 5. Weiterführende Zeichenwerkzeuge 6. Layout und Plotten
KW - CAD
KW - AutoCAD
KW - AutoCAD 2005
KW - AutoCAD
Y1 - 2006
N1 - Zugriff nur über das Intranet der FH Aachen
ER -
TY - GEN
A1 - Höttges, Jörg
A1 - Cordes, Jürgen
A1 - Wirtz, Dominika
A1 - Moers, Monika
A1 - Gehlen, Tanja
A1 - Aldenhoven, Frederick
T1 - E-Learning Access
N2 - Schrittweise Einführung in Access. Nach jedem Abschnitt besteht die Möglichkeit, das neue Wissen direkt anzuwenden. Mit Wissensprüfungen und Übungen nach jedem Kapitel. 1. Grundbegriffe aus der Datenbank 2. Eine Datenbank planen 3. Tabellen erstellen und bearbeiten 4. Abfragen erstellen und bearbeiten 5. Formulare - Tuning für die Daten 6. Berichte - echt einfach
KW - ACCESS 2003
KW - ACCESS
KW - Relationale Datenbank
KW - Access
Y1 - 2006
N1 - Zugriff nur über das Intranet der FH Aachen
ER -
TY - JOUR
A1 - Gebhardt, Andreas
T1 - Grundlagen des Rapid Prototyping: Eine Kurzdarstellung der Rapid Prototyping Verfahren
N2 - Generative Verfahren sind seit etwa 1987 in den USA und seit etwa 1990 in Europa und Deutschland in Form von Rapid Prototyping Verfahren bekannt und haben sich in dieser Zeit von eher als exotisch anzusehenden Modellbauverfahren zu effizienten Werkzeugen für die Beschleunigung der Produktentstehung gewandelt. Mit der Weiterentwicklung der Verfahren und insbesondere der Materialien wird mehr und mehr das Feld der direkten Anwendung der Rapid Technologie zur Fertigung erschlossen. Rapid Technologien werden daher zum Schlüssel für neue Konstruktionssystematiken und Fertigungsstrategien.
N2 - Generative procedures have been known under the term of 'rapid prototyping method' for about 18 years in the USA and about 15 years in Europe and Germany. In this time they changed from what was regarded as being a rather exotic way of model construction procedures to a very efficient and useful instrument for faster product manufacturing. In the course of the further development of the methods, and in particular the materials, the field for direct application of rapid technology opens up for manufacturing. Therefore rapid technologies become the key for new construction systematics and manufacturing strategies.
KW - Rapid prototyping
KW - Laserstrahlsintern
KW - 3D-Printing
KW - Extrusionsverfahren
KW - Gießharzwerkzeuge
KW - Laminat Verfahren
KW - Lasersintern
KW - Stereolithographie
KW - Vakuumgießen
KW - FLM
KW - Fused deposition modelling
KW - Laminated-Object-Manufacturing
Y1 - 2004
ER -
TY - JOUR
A1 - Gebhardt, Andreas
T1 - Rapid Prototyping für metallische Werkstücke: Direkte und indirekte Verfahren
N2 - Die generative Herstellung von Kunststoffbauteilen hat im Gewand des Rapid Prototyping die Produktentwicklung nachhaltig positiv beeinflusst und ist im Begriff als Rapid Manufacturing die Fertigung zu revolutionieren. Je mehr sich die besonderen Eigenschaften generativ gefertigter Kunststoffbauteile herumsprechen, desto lauter wird der Ruf nach Metallbauteilen. Die Entwicklung entsprechender Prozesse läuft auf Hochtouren, kann aber bisher aber erst vereinzelt Erfolge vorweisen. Dabei wären es gerade die Metallbauteile, die ausgestattet mit den besonderen Merkmalen generativ gefertigter Werkstücke, in vielen Branchen einen deutlichen Entwicklungsschub auslösen könnten. Für den potenziellen Anwender ist dabei besonders verwirrend, dass die unterschiedlichsten Ansätze nebeneinander verfolgt werden. Im Folgenden soll daher der Versuche unternommen werden, dieses weite Feld systematisiert darzustellen und Möglichkeiten und Trends zu erläutern.
N2 - The generative manufacturing of plastic components via rapid prototyping has positively affected the product development. As 'rapid manufacturing' the method is about to revolutionize the manufacturing in general. The more the special characteristics of generative manufactured plastic components are getting about, the louder becomes the call for generative manufactured metal components. The development of analogical processes runs on full speed. So far however, only sporadic successes can be registered. Though there are in particular the metal components which could, equipped with the special characteristics of generative manufactured components, initiate a developmental boost in many industries. For the potential operator it is particularly confusing that the different approaches are traced parallel. Therefore in the following contribution the attempt is undertaken not only to represent this wide field in a systematic way but to describe possibilities and trends as well.
KW - Rapid prototyping
KW - Rapid Prototyping
KW - Rapid Manufacturing
KW - generative Fertigungsverfahren
KW - Werkzeugeinsätze
KW - Werkzeuge
KW - Rapid prototyping
KW - rapid manufacturing
Y1 - 2005
ER -
TY - JOUR
A1 - Gebhardt, Andreas
A1 - Brücker, Christoph
A1 - Schmidt, Frank-Michael
T1 - RP gestützte Herstellung komplexer transparenter Hohlräume für die Strömungsanalyse
N2 - Die Berechnung der Durchströmung von Bauteilen ist gegenüber derjenigen von umströmten Bauteilen deutlich im Hintertreffen. Das liegt vor allem an der fehlenden Verfügbarkeit geeigneter optisch transparenter Modellkanäle für die experimentelle Analyse. Der Beitrag stellt ein Verfahren zur Herstellung transparenter durchströmter Geometrien auf der Basis generativ gefertigter Urmodelle vor. Damit können beliebig komplexe Innenströmungen optisch analysiert werden. Anhand von zwei Beispielen aus der Medizin, der Modellierung der oberen Atemwege und des Bronchialbaums, wird das Verfahren vorgeführt. Der generative Bauprozess mittels 3D-Printing wird beschrieben und die Abformung in transparentem Silikon gezeigt. Schließlich werden beispielhaft der Messaufbau und Ergebnisse der Anwendung vorgestellt. Das Verfahren bildet die Grundlage für die Analyse und Berechnung komplexer Innenströmungen und trägt somit zur Verbesserung zahlreicher technischer Anwendungen bei.
N2 - Unlike the flow around technical products the interior flow is not understood very well. That’s mainly because of a lack of suitable transparent investigation tunnels that are needed to apply optical methods. The paper proposes a procedure to make precise complex hollow structures from a highly transparent material using masters from generative or Rapid Prototyping processes. Taking two examples from the medical field, the upper human airways and the bronchial tree, the entire process is shown. The 3D Printing build process is illustrated as well as the silicon casting process. Finally the measuring equipment is demonstrated and sample results are given. The process establishes the basis for the investigation and calculation of complex interior flow pattern and therefore contributes to a better understanding and consequently improvement of appropriate technical products.
KW - Rapid prototyping
KW - Rapid Prototyping
KW - Strömungsanalyse
KW - Innenströmung
KW - Modellkanäle
KW - 3D-Printing
Y1 - 2005
ER -
TY - JOUR
A1 - Gebhardt, Andreas
T1 - Rapid Manufacturing - eine interdisziplinäre Strategie
N2 - Als um 1987 ein Verfahren namens Stereolithographie und ein Stereolithography Apparatus (SLA) vorgestellt wurden, war der Traum von der Herstellung beliebiger dreidimensionaler Bauteile direkt aus Computerdaten und ohne bauteilspezifische Werkzeuge Realität geworden. Ein Anwendungs-Szenario wurde gleich mitgeliefert. Diese Technologie würde es möglich machen, die gesamte Ersatzteilversorgung der Amerikanischen Pazifikflotte mittels ein paar dieser Maschinen, umfangreicher Datenstätze und genügend Rohmaterial vor Ort auf einem Flugzeugträger direkt nach Bedarf zu fertigen. Diese Vorstellung definierte schon damals die direkte digitale Fertigung, das Rapid Manufacturing. In der Realität bestanden die mit diesem Verfahren hergestellten Bauteile nur aus Kunststoff, waren ungenau, bruchempfindlich und klebrig und allein in der Produktentwicklung, eben als Prototypen zu benutzen. Sie waren schnell verfügbar, weil zu Ihrer Herstellung keine Werkzeuge benötigt wurden. Folgerichtige und zudem modern hießen sie: Rapid Prototyping. Rapid Prototyping wurde schnell zum Synonym eines neuen Zweiges der Fertigungstechnik, der Generativen Fertigungstechnik. Die weitere Entwicklung brachte neue Verfahren, höhere Genauigkeiten, verbesserte Werkstoffe und neue Anwendungen. Die Herstellung von Negativen, also Werkzeugen, mit dem gleichen Verfahren wurde marketing-getrieben Rapid Tooling genannt und als die ersten Bauteile nicht mehr als Prototypen, sondern als Endprodukte eingesetzt wurden, nannte man dies Rapid Manufacturing - das Ziel war erreicht. War das Ziel wirklich erreicht? Ist es Rapid Manufacturing, wenn ein generativ gefertigtes Bauteil die gewünschte Spezifikation erreicht? Was muss passieren, damit aus dem Phänomen Rapid Prototyping eine Strategie wird, die geeignet ist, einen Paradigmenwechsel von der heutigen Hersteller-induzierten Massenproduktion von Massenartikeln zur Verbraucher-induzierten (und verantworteten) Massenproduktion von Einzelteilen für jedermann ermöglichen und möglicherweise unsere Arbeits- und Lebensformen tiefgreifend zu beeinflussen? Im Beitrag wird der Begriff der (Fertigungs-) Strategie „Rapid Manufacturing“ näher beleuchtet. Es wird diskutiert, welche Maßnahmen auf der technischen und der operative Ebene getroffen werden müssen, damit die generative Fertigungstechnik im Sinne dieser Strategie umgesetzt werden kann. Beispiele belegen, dass diese Entwicklung bereits begonnen hat und geben Anregungen für eine konstruktive Diskussion auf der RapidTech 2006.
N2 - As a process called stereolithography and a stereolithography apparatus (SLA) was presented in 1987, the dream of manufacturing any three-dimensional component directly from computer data and without component-specific tools became reality. An application scenario was supplied at the same time. This technology would make it possible to produce the entire spare parts requirement of the American Pacific Fleet merely through the use of a couple of such machines, extensive datasets and enough raw material on board an aircraft carrier directly as required. This image defined direct digital fabrication, rapid manufacturing, even at that time. In reality, this procedure only managed to produce components in plastic which were imprecise, fragile and sticky and only usable as prototypes in product development. They were rapidly available, because no tools were required for their manufacture. Consequentially, they are now known as Rapid Prototyping in modern jargon. Rapid Prototyping quickly became a synonym for a new branch of production engineering known as generative production engineering. Continued development brought new processes, improved accuracy, improved materials and new applications. The manufacturing of negatives, in other words tools, using the same procedure was quickly named rapid tooling by the marketing sector, and once the first components were used as final products instead of just prototypes the process was renamed "rapid manufacturing" - the goal had been reached. Was the goal really reached? Is it rapid manufacturing if a generatively manufactured component reaches the required specifications? What has to happen so that the rapid prototyping phenomenon becomes a strategy which is suitable for enabling the paradigm change from current manufacture-induced mass production of mass articles to consumer-induced (and consumer-responsible) mass production of single parts for anyone, and in all possibility makes dramatic changes in our way of working and living? The lecture includes detailed information about the (production) strategy term "rapid manufacturing". We will be discussing which measures need to be taken on the technical and operative level so that generative production engineering can be implemented in the sense of this strategy. Examples will show that this development has already started, and should provoke stimulation leading to constructive discussion during RapidTech 2006.
KW - Rapid prototyping
KW - Rapid Manufacturing
KW - Rapid Prototyping
KW - Stereolithographie
KW - Generative Fertigungstechnik
KW - Rapid prototyping
KW - rapid manufacturing
Y1 - 2006
ER -
TY - CHAP
A1 - Brüssermann, Klaus
T1 - Platform of Excellence in "Energy and Environment"
N2 - The Ministry of Science and Research in North Rhine-Westphalia created eight platforms of excellence, one in the research area „Energy and Environment“ in 2002 at ACUAS. This platform concentrates the research and development of 13 professors in Jülich and Aachen and of two scientific institutes with different topics: – NOWUM-Energy with emphasis on efficient and economic energy conversion – The Solar Institute Jülich – SIJ – being the largest research institute in the field of renewables at a University of Applied Sciences in Germany With this platform each possible energy conversion – nuclear, fossil, renewable- can be dealt with to help solving the two most important problems of mankind, energy and potable water. At the CSE are presented the historical development, some research results and the combined master studies in „Energy Systems“ and „Nuclear Applications“
KW - Energietechnik
KW - Kernenergie
KW - Umwelt
KW - Energy
KW - environment
KW - Energy Systems
KW - Nuclear Applications
Y1 - 2005
ER -
TY - JOUR
A1 - Frings, Michael
T1 - Anwendung des Haustürgeschäftewiderrufsgesetzes unter Angehörigen (BGH, Urteil vom 17.09.1996)
JF - Wirtschaftsrechtliche Beratung : WiB ; Zeitschrift für Wirtschaftsanwälte und Unternehmensjuristen (1997)
Y1 - 1997
SN - 0945-2346 ; 0946-244
SP - 148
ER -
TY - JOUR
A1 - Frings, Michael
T1 - Prozessvergleich mit Verfallklausel (OLG Düsseldorf, Urteil vom 04.05.1995)
JF - Entscheidungen zum Wirtschaftsrecht : EWiR ; Kurzkommentare (1997)
Y1 - 1997
SN - 0177-9303
SP - 931
ER -
TY - JOUR
A1 - Frings, Michael
T1 - Missverhältnis zwischen Leistung und Gegenleistung bei Abfindungsvereinbarungen (BGH, Urteil vom 02.07.1999)
JF - Entscheidungen zum Wirtschaftsrecht : EWiR ; Kurzkommentare (1999)
Y1 - 1999
SN - 0177-9303
SP - 987
ER -
TY - JOUR
A1 - Frings, Michael
T1 - Aufklärungspflicht des Initiators eines geschlossenen Immobilienfonds gegenüber einem Anleger (KG, Urteil vom 25.11.1999)
JF - Entscheidungen zum Wirtschaftsrecht : EWiR ; Kurzkommentare (2000)
Y1 - 2000
SN - 0177-9303
SP - 417
ER -
TY - JOUR
A1 - Frings, Michael
T1 - Auslegung einer Bürgerschaftsvereinbarung (BGH, Urteil vom 09.07.2001)
JF - Entscheidungen zum Wirtschaftsrecht : EWiR ; Kurzkommentare (2001)
Y1 - 2001
SN - 0177-9303
SP - 849
ER -
TY - JOUR
A1 - Frings, Michael
T1 - Tendenzwende in der Rechtsprechung zur Anwendung des HWiG auf Angehörige
JF - Verbraucher und Recht : VuR (1997)
Y1 - 1997
SN - 0930-8369
SP - 201
EP - 205
ER -
TY - JOUR
A1 - Frings, Michael
T1 - Das neue Verbraucherschutzrecht im BGB
JF - Verbraucher und Recht : VuR (2002)
Y1 - 2002
SN - 0930-8369
SP - 390
EP - 398
ER -
TY - JOUR
A1 - Frings, Michael
T1 - Verbesserter Verbraucherschutz bei kreditfinanzierten Immobiliengeschäften
JF - Verbraucher und Recht : VuR (2004)
Y1 - 2004
SN - 0930-8369
SP - 404
EP - 410
ER -
TY - BOOK
A1 - Grap, Rolf Dietmar
T1 - Gestaltung menschengerechter Arbeitsplätze in der Schulbuchproduktion: Ergebnisse der Ist-Analyse - Arbeitswissenschaftlicher Teil
Y1 - 1989
N1 - Untersuchungsbericht des BMFT zum Projekt 01
PB - IAW - Lehrstuhl und Institut für Arbeitswissenschaft der RWTH Aachen
CY - Aachen
ER -
TY - BOOK
A1 - Grap, Rolf Dietmar
T1 - Gestaltung menschengerechter Arbeitsplätze in der Schulbuchproduktion: Vorschläge zum Sollkonzept - Arbeitswissenschaftlicher Teil
Y1 - 1989
N1 - Untersuchungsbericht des BMFT zum Projekt 01
PB - IAW - Lehrstuhl und Institut für Arbeitswissenschaft der RWTH Aachen
CY - Aachen
ER -
TY - JOUR
A1 - Gebhardt, Andreas
T1 - Lasereinsatz in der Fertigung der Fahrzeugindustrie. Grundlagen der Anwendung von Lasern zur Materialbearbeitung
Y1 - 1997
N1 - Konferenz-Einzelbericht : Laseranwendungen im Automobilbau, 1. Euroforum-Anwenderkonferenz zum Lasereinsatz, Nürtingen, DE, 23.-24. Okt, 1997
SP - 1
EP - 154
ER -
TY - JOUR
A1 - Gebhardt, Andreas
A1 - Schmachtenberg, E.
T1 - Rapid Prototyping und Tooling
Y1 - 1996
N1 - Konferenz-Einzelbericht : 7. Würzburger Werkzeugtage, Produktivitätsverbesserungen, neue Technologien, Fachtagung, Würzburg, DE, 24.-25. Sep, 1996
SP - 1
EP - 20
ER -
TY - JOUR
A1 - Gebhardt, Andreas
A1 - Plum, H.D.
A1 - Mathar, W.
A1 - Wolf, M.
T1 - TrueForm - erste Anwendung des neuen Sintermaterials mit Vakuumgießen und Investmentgießen
Y1 - 1996
N1 - Konferenz-Einzelbericht : RPD, Internat. Conf. on Rapid Product Development, Proc., Stuttgart, DE, Jun 10-11
SP - 231
EP - 236
ER -
TY - JOUR
A1 - Gebhardt, Andreas
A1 - Guntermann, P.
A1 - Saur, G.
A1 - Gartzen, Johannes
T1 - Neue Impulse für den Leichtbau. Ein Konstruktionsprinzip für Verbauplatten mit Laserschweißen am verdeckten Stoß.
JF - Laser-Praxis (1996)
Y1 - 1996
SN - 0937-7069
SP - 21
EP - 24
ER -
TY - JOUR
A1 - Gebhardt, Andreas
T1 - Rapid Prototyping - Laser-gestützte Revolution der Produktentwicklung. Teil I
JF - Laser Magazin (1996)
Y1 - 1996
SN - 0945-8875
SP - 6
EP - 9
ER -
TY - JOUR
A1 - Gebhardt, Andreas
A1 - Plug, T-K.
T1 - Innovationsschub mittels Rapid-Prototyping, Teil II
JF - CAD-CAM Report. 14 (1995), H. 9
Y1 - 1995
SN - 0930-7117
SP - 78
EP - 85
ER -
TY - JOUR
A1 - Gebhardt, Andreas
A1 - Pflug, T-K.
T1 - Innovationsschub mittels Rapid-Prototyping. Teil I
JF - CAD-CAM Report. 14 (1995), H. 7
Y1 - 1995
SN - 0930-7117
SP - 56
EP - 65
ER -
TY - JOUR
A1 - Grap, Rolf Dietmar
T1 - Grafische Modelle vom Innenleben des Computers : Demonstrationsversion des IAW zur Simulation prozeßorientierter Abläufe bei der Programmausführung
JF - Fir- + Iaw-Mitteilungen / Forschungsinstitut für Rationalisierung ; Institut für Arbeitswissenschaft, Technische Hochschule Aachen (1990)
Y1 - 1990
SN - 0934-6430
N1 - Forschungsinstitut für Rationalisierung ; Institut für Arbeitswissenschaft
SP - 7
PB - Inst.
CY - Aachen
ER -
TY - BOOK
A1 - Grap, Rolf Dietmar
T1 - Neue Formen der Arbeitsorganisation/1 (1993)
Y1 - 1993
SN - 3-86073-096-7
PB - Verl. der Augustinus-Buchh.
CY - Aachen
ER -
TY - BOOK
A1 - Grap, Rolf Dietmar
T1 - Neue Formen der Arbeitsorganisation/2 (1993)
Y1 - 1993
SN - 3-86073-096-7
PB - Verl. der Augustinus-Buchh.
CY - Aachen
ER -
TY - BOOK
A1 - Grap, Rolf Dietmar
T1 - Neue Formen der Arbeitsorganisation für die Stahlindustrie
Y1 - 1992
SN - 3-86073-088-6
N1 - Aachener Beiträge zu Humanisierung und Rationalisierung ; 4 ; Zugl.: Aachen, Techn. Hochsch., Diss., 1992
PB - Augustinus-Buchhandlung Kerres
CY - Aachen
ER -
TY - BOOK
A1 - Grap, Rolf Dietmar
T1 - Produktion und Beschaffung: eine praxisorientierte Einfühung
Y1 - 1998
SN - 3-8006-2321-8
PB - Vahlen
CY - München
ER -
TY - BOOK
A1 - Grap, Rolf Dietmar
A1 - Heberer, Juliane
T1 - Betriebliche Weiterbildung in kleinen und mittelständischen Unternehmen: Methoden und Vorgehensweisen / Juliane Heberer ; Rolf Grap
Y1 - 1995
SN - 3-931196-00-3
N1 - Die grüne Reihe aus dem GOM-Verlag ; 1
PB - Verl. der GOM
CY - Herzogenrath
ER -
TY - BOOK
A1 - Grap, Rolf Dietmar
T1 - Lernkultur Kompetenzentwicklung: neue Ansätze zum Lernen im Beruf / Grap, Rolf [Hrsg.]
Y1 - 2002
SN - 3-8322-1042-3
N1 - Berichte aus der Betriebswirtschaft
PB - Shaker
CY - Aachen
ER -