TY - JOUR A1 - Pourshahidi, Ali Mohammad A1 - Engelmann, Ulrich M. A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim T1 - Resolving ambiguities in core size determination of magnetic nanoparticles from magnetic frequency mixing data JF - Journal of Magnetism and Magnetic Materials N2 - Frequency mixing magnetic detection (FMMD) has been widely utilized as a measurement technique in magnetic immunoassays. It can also be used for the characterization and distinction (also known as “colourization”) of different types of magnetic nanoparticles (MNPs) based on their core sizes. In a previous work, it was shown that the large particles contribute most of the FMMD signal. This leads to ambiguities in core size determination from fitting since the contribution of the small-sized particles is almost undetectable among the strong responses from the large ones. In this work, we report on how this ambiguity can be overcome by modelling the signal intensity using the Langevin model in thermodynamic equilibrium including a lognormal core size distribution fL(dc,d0,σ) fitted to experimentally measured FMMD data of immobilized MNPs. For each given median diameter d0, an ambiguous amount of best-fitting pairs of parameters distribution width σ and number of particles Np with R2 > 0.99 are extracted. By determining the samples’ total iron mass, mFe, with inductively coupled plasma optical emission spectrometry (ICP-OES), we are then able to identify the one specific best-fitting pair (σ, Np) one uniquely. With this additional externally measured parameter, we resolved the ambiguity in core size distribution and determined the parameters (d0, σ, Np) directly from FMMD measurements, allowing precise MNPs sample characterization. Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.jmmm.2022.169969 SN - 0304-8853 VL - 563 IS - In progress, Art. No. 169969 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Engelmann, Ulrich M. A1 - Pourshahidi, Mohammad Ali A1 - Shalaby, Ahmed A1 - Krause, Hans-Joachim T1 - Probing particle size dependency of frequency mixing magnetic detection with dynamic relaxation simulation JF - Journal of Magnetism and Magnetic Materials N2 - Biomedical applications of magnetic nanoparticles (MNP) fundamentally rely on the particles’ magnetic relaxation as a response to an alternating magnetic field. The magnetic relaxation complexly depends on the interplay of MNP magnetic and physical properties with the applied field parameters. It is commonly accepted that particle core size is a major contributor to signal generation in all the above applications, however, most MNP samples comprise broad distribution spanning nm and more. Therefore, precise knowledge of the exact contribution of individual core sizes to signal generation is desired for optimal MNP design generally for each application. Specifically, we present a magnetic relaxation simulation-driven analysis of experimental frequency mixing magnetic detection (FMMD) for biosensing to quantify the contributions of individual core size fractions towards signal generation. Applying our method to two different experimental MNP systems, we found the most dominant contributions from approx. 20 nm sized particles in the two independent MNP systems. Additional comparison between freely suspended and immobilized MNP also reveals insight in the MNP microstructure, allowing to use FMMD for MNP characterization, as well as to further fine-tune its applicability in biosensing. Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.jmmm.2022.169965 SN - 0304-8853 VL - 563 IS - In progress, Art. No. 169965 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Allal, D. A1 - Bannister, R. A1 - Buisman, K. A1 - Capriglione, D. A1 - Di Capua, G. A1 - García-Patrón, M. A1 - Gatzweiler, Thomas A1 - Gellersen, F. A1 - Harzheim, Thomas A1 - Heuermann, Holger A1 - Hoffmann, J. A1 - Izbrodin, A. A1 - Kuhlmann, K. A1 - Lahbacha, K. A1 - Maffucci, A. A1 - Miele, G. A1 - Mubarak, F. A1 - Salter, M. A1 - Pham, T.D. A1 - Sayegh, A. A1 - Singh, D. A1 - Stein, F. A1 - Zeier, M. T1 - RF measurements for future communication applications: an overview T2 - 2022 IEEE International Symposium on Measurements & Networking (M&N) N2 - In this paper research activities developed within the FutureCom project are presented. The project, funded by the European Metrology Programme for Innovation and Research (EMPIR), aims at evaluating and characterizing: (i) active devices, (ii) signal- and power integrity of field programmable gate array (FPGA) circuits, (iii) operational performance of electronic circuits in real-world and harsh environments (e.g. below and above ambient temperatures and at different levels of humidity), (iv) passive inter-modulation (PIM) in communication systems considering different values of temperature and humidity corresponding to the typical operating conditions that we can experience in real-world scenarios. An overview of the FutureCom project is provided here, then the research activities are described. KW - FPGA KW - signal integrity KW - power integrity KW - passive inter-modulation KW - metrological characterization Y1 - 2022 SN - 978-1-6654-8362-9 SN - 978-1-6654-8363-6 U6 - http://dx.doi.org/10.1109/MN55117.2022.9887740 SN - 2639-5061 SN - 2639-507X N1 - 2022 IEEE International Symposium on Measurements & Networking (M&N), 18-20 July 2022, Padua, Italy. SP - 1 EP - 6 PB - IEEE ER - TY - JOUR A1 - Philipp, Mohr A1 - Efthimiou, Nikos A1 - Pagano, Fiammetta A1 - Kratochwil, Nicolaus A1 - Pizzichemi, Marco A1 - Tsoumpas, Charalampos A1 - Auffray, Etiennette A1 - Ziemons, Karl T1 - Image reconstruction analysis for positron emission tomography with heterostructured scintillators JF - IEEE Transactions on Radiation and Plasma Medical Sciences N2 - The concept of structure engineering has been proposed for exploring the next generation of radiation detectors with improved performance. A TOF-PET geometry with heterostructured scintillators with a pixel size of 3.0×3.1×15 mm3 was simulated using Monte Carlo. The heterostructures consisted of alternating layers of BGO as a dense material with high stopping power and plastic (EJ232) as a fast light emitter. The detector time resolution was calculated as a function of the deposited and shared energy in both materials on an event-by-event basis. While sensitivity was reduced to 32% for 100 μm thick plastic layers and 52% for 50 μm, the CTR distribution improved to 204±49 ps and 220±41 ps respectively, compared to 276 ps that we considered for bulk BGO. The complex distribution of timing resolutions was accounted for in the reconstruction. We divided the events into three groups based on their CTR and modeled them with different Gaussian TOF kernels. On a NEMA IQ phantom, the heterostructures had better contrast recovery in early iterations. On the other hand, BGO achieved a better contrast to noise ratio (CNR) after the 15th iteration due to the higher sensitivity. The developed simulation and reconstruction methods constitute new tools for evaluating different detector designs with complex time responses. KW - TOF PET KW - Heterostructure KW - Metascintillator KW - Multiple TOF kernels KW - Image Reconstruction Y1 - 2022 U6 - http://dx.doi.org/10.1109/TRPMS.2022.3208615 SN - 2469-7311 SN - 2469-7303 VL - 7 IS - 1 SP - 41 EP - 51 PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Hinke, Christian A1 - Vervier, Luisa A1 - Brauner, Philipp A1 - Schneider, Sebastian A1 - Steuer-Dankert, Linda A1 - Ziefle, Martina A1 - Leicht-Scholten, Carmen T1 - Capability configuration in next generation manufacturing T2 - Forecasting next generation manufacturing : digital shadows, human-machine collaboration, and data-driven business models N2 - Industrial production systems are facing radical change in multiple dimensions. This change is caused by technological developments and the digital transformation of production, as well as the call for political and social change to facilitate a transformation toward sustainability. These changes affect both the capabilities of production systems and companies and the design of higher education and educational programs. Given the high uncertainty in the likelihood of occurrence and the technical, economic, and societal impacts of these concepts, we conducted a technology foresight study, in the form of a real-time Delphi analysis, to derive reliable future scenarios featuring the next generation of manufacturing systems. This chapter presents the capabilities dimension and describes each projection in detail, offering current case study examples and discussing related research, as well as implications for policy makers and firms. Specifically, we discuss the benefits of capturing expert knowledge and making it accessible to newcomers, especially in highly specialized industries. The experts argue that in order to cope with the challenges and circumstances of today’s world, students must already during their education at university learn how to work with AI and other technologies. This means that study programs must change and that universities must adapt their structural aspects to meet the needs of the students. Y1 - 2022 SN - 978-3-031-07733-3 U6 - http://dx.doi.org/10.1007/978-3-031-07734-0_6 SP - 95 EP - 106 PB - Springer CY - Cham ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Leicht-Scholten, Carmen T1 - Perceiving diversity : an explorative approach in a complex research organization. T2 - Diversity and discrimination in research organizations N2 - Diversity management is seen as a decisive factor for ensuring the development of socially responsible innovations (Beacham and Shambaugh, 2011; Sonntag, 2014; López, 2015; Uebernickel et al., 2015). However, many diversity management approaches fail due to a one-sided consideration of diversity (Thomas and Ely, 2019) and a lacking linkage between the prevailing organizational culture and the perception of diversity in the respective organization. Reflecting the importance of diverse perspectives, research institutions have a special responsibility to actively deal with diversity, as they are publicly funded institutions that drive socially relevant development and educate future generations of developers, leaders and decision-makers. Nevertheless, only a few studies have so far dealt with the influence of the special framework conditions of the science system on diversity management. Focusing on the interdependency of the organizational culture and diversity management especially in a university research environment, this chapter aims in a first step to provide a theoretical perspective on the framework conditions of a complex research organization in Germany in order to understand the system-specific factors influencing diversity management. In a second step, an exploratory cluster analysis is presented, investigating the perception of diversity and possible influencing factors moderating this perception in a scientific organization. Combining both steps, the results show specific mechanisms and structures of the university research environment that have an impact on diversity management and rigidify structural barriers preventing an increase of diversity. The quantitative study also points out that the management level takes on a special role model function in the scientific system and thus has an influence on the perception of diversity. Consequently, when developing diversity management approaches in research organizations, it is necessary to consider the top-down direction of action, the special nature of organizational structures in the university research environment as well as the special role of the professorial level as role model for the scientific staff. KW - Diversity management KW - Organizational culture KW - Change management KW - Psychological concepts KW - Perception Y1 - 2022 SN - 978-1-80117-959-1 (Print) SN - 978-1-80117-956-0 (Online) U6 - http://dx.doi.org/10.1108/978-1-80117-956-020221010 SP - 365 EP - 392 PB - Emerald Publishing Limited CY - Bingley ER - TY - CHAP A1 - Striebing, Clemens A1 - Müller, Jörg A1 - Schraudner, Martina A1 - Gewinner, Irina Valerie A1 - Guerrero Morales, Patricia A1 - Hochfeld, Katharina A1 - Hoffman, Shekinah A1 - Kmec, Julie A. A1 - Nguyen, Huu Minh A1 - Schneider, Jannick A1 - Sheridan, Jennifer A1 - Steuer-Dankert, Linda A1 - Trimble O'Connor, Lindsey A1 - Vandevelde-Rougale, Agnès T1 - Promoting diversity and combatting discrimination in research organizations: a practitioner’s guide T2 - Diversity and discrimination in research organizations N2 - The essay is addressed to practitioners in research management and from academic leadership. It describes which measures can contribute to creating an inclusive climate for research teams and preventing and effectively dealing with discrimination. The practical recommendations consider the policy and organizational levels, as well as the individual perspective of research managers. Following a series of basic recommendations, six lessons learned are formulated, derived from the contributions to the edited collection on “Diversity and Discrimination in Research Organizations.” KW - Inclusive work climate KW - lessons learned KW - policy recommendations KW - recommendations for actions KW - bullying Y1 - 2022 SN - 978-1-80117-959-1 (Print) SN - 978-1-80117-956-0 (Online) U6 - http://dx.doi.org/10.1108/978-1-80117-956-020221012 SP - 421 EP - 442 PB - Emerald Publishing Limited CY - Bingley ER - TY - THES A1 - Eigel, Nick T1 - uCo - the universal communicator : robotische Konversationen unserer Zukunft N2 - Kommunikationsroboter für den Kundenservice. Aktuell werden große Fortschritte im Bereich von künstlicher Intelligenz und Robotik getätigt, sodass wir bald intelligente Maschinen unter uns haben werden. Daher müssen wir uns die Frage beantworten, welche Rolle diese einnehmen sollen und vor allem wie wir mit ihnen interagieren und kommunizieren wollen. "uCo" bewältigt dies mithilfe einer mobilen, robotischen Plattform, welche mit einem holografischen 3-D-Interface ausgestattet ist. Neben der Entwicklung des robotischen Körpers beinhaltet das Projekt "uCo" die Grundlage für ein Kommunikationssystem für "uCo's" Gesicht. "uCo" kommuniziert hauptsächlich über Sprache, wird dabei jedoch von einem speziell entwickelten Mimik- und Emotionssytem unterstützt. "uCo" als Konzept versucht, erste Antworten auf die komplexen gestalterischen und moralischen Fragen zu geben, die mit der Entwicklung von künstlicher Intelligenz einhergehen. Und wer weiß - vielleicht wirst du eines Tages von einem "uCo" beraten. KW - Robotik KW - Hologram KW - Kommunikation KW - künstliche Intelligenz KW - KI Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Geilhausen, Ayleen T1 - SUE : Restauranterlebnisse neu gestalten N2 - Gastronomiebetriebe, insbesondere diese ohne zeitgemäße und durchdachte Konzepte wurden durch die Pandemie stark getroffen. Während große Fast-Food-Ketten bereits vor der Pandemie digitale Lösungen einsetzten, stehen nun auch andere Restaurantbetreiber:innen vor der Herausforderung der Digitalisierung. Gerade die Pandemie hat an dieser Stelle verdeutlicht, welche Restaurants ihre Prozesse im Sinne der User Experience durchdacht haben und welche nicht. Die Tisch-Stuhl-Kombination der „SUE“-Serie bietet Restaurants, smarte und elegante Gastronomiemöbel, die je nach Konzept in Materialität und Farbe frei anpassbar sind. Wandelbarkeit, Komfort und die Integration digitaler Lösungen sind die Kernkompetenzen und Anforderungen, die das Gastronomie-Interior in Zukunft erfüllen muss. Der smarte Bistrotisch und der wandelbare Stuhl der „SUE“-Serie zeigt einen digitalisierten und anpassbaren Lösungsansatz. KW - Restaurantmöbel KW - Gastronomie KW - Designstuhl KW - Restauranttisch KW - Produktdesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Zähl, Philipp M. A1 - Biewendt, Marcel A1 - Wolf, Martin A1 - Eggert, Mathias T1 - Requirements for Competence Developing Games in the Environment of SE Competence Development T2 - Angewandte Forschung in der Wirtschaftsinformatik 2022 N2 - Many of today’s factors make software development more and more complex, such as time pressure, new technologies, IT security risks, et cetera. Thus, a good preparation of current as well as future software developers in terms of a good software engineering education becomes progressively important. As current research shows, Competence Developing Games (CDGs) and Serious Games can offer a potential solution. This paper identifies the necessary requirements for CDGs to be conducive in principle, but especially in software engineering (SE) education. For this purpose, the current state of research was summarized in the context of a literature review. Afterwards, some of the identified requirements as well as some additional requirements were evaluated by a survey in terms of subjective relevance. KW - software engineering KW - requirements KW - competence developing games KW - systematic literature review Y1 - 2022 SN - 978-3-95545-409-8 U6 - http://dx.doi.org/10.30844/AKWI_2022_05 N1 - Tagungsband zur 35. Jahrestagung des Arbeitskreises Wirtschaftsinformatik an Hochschulen für Angewandte Wissenschaften im deutschsprachigen Raum (AKWI) vom 11.09. bis 13.09.2022, ausgerichtet von der Hochschule für Technik und Wirtschaft Berlin (HTW Berlin) und der Hochschule für Wirtschaft und Recht Berlin (HWR Berlin) SP - 73 EP - 88 PB - GITO CY - Berlin ER - TY - THES A1 - Buhr, Amelie T1 - Entschleunigen : warum unser Modekonsum verlangsamt werden muss N2 - In Zeiten von Schnelllebigkeit ändern immer mehr Menschen bewusst ihren Umgang mit alltäglichen Dingen. Was dabei häufig in den Hintergrund rückt, ist das Thema "bewusste Kleidung". Beeinflusst durch sogenannte Fast-Fashion-Modeketten und Social Media leben wir in einer regelrechten Wegwerfgesellschaft. „Entschleunigen“ beschäftigt sich mit den Schattenseiten der Modeindustrie, zeigt aber ebenso (neue) Wege auf, die auf eine bessere Zukunft für uns und unsere Umwelt hoffen lassen. Aufgeteilt in zwei Kapitel gibt „Entschleunigen“ einen Einblick in den ökologischen und sozialen Fußabdruck der Modeindustrie und stellt zum anderen die Gegenseite vor, bei der Wert auf faire Produktion und Nachhaltigkeit gelegt wird. Das Buch „Entschleunigen“ soll über die Missstände in der Textilbranche informieren, jedoch im Umkehrschluss dazu motivieren, diese mit einfachen Mitteln zu verbessern. KW - Modeindustrie KW - Kleidung KW - langsam KW - schnell KW - nachhaltig Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Cekic, Dilara T1 - Visionsbild eines BMW AG internen Tools : Optimierung einer datenzentrierten Plattform der BMW AG N2 - Die BMW AG verfolgt mehrere Ansätze eine optimierte Effizienzsteigerung durch eigens entwickelte Softwaretools zu erreichen. Der Fokus hierbei liegt in der Ermöglichung einer datenzentrierten, nutzerorientierten und hochautomatisierten Fahrzeugentwicklung. Das eigen von der BMW AG entwickelte Software-Tool „Parts List“ dient als digitale Bauteilliste für Entwicklungsteams. Das Tool bündelt mehrere Datenbanken und stellt diese in Echtzeit zur Verfügung. Somit kann der manuelle Pflegeaufwand erheblich reduziert und eine Durchgängigkeit einer Vielzahl von Daten ermöglicht werden. Der Fokus der Abschlussarbeit liegt in der konzeptionellen und gestalterischen Optimierung des Tools. Dabei wird insbesondere der User Centered Design Prozess betrachtet, bei dem die Nutzer bzw. die Entwicklungsteams im Zentrum stehen. KW - UX/UI Design KW - Nutzeroberfläche KW - BMW AG KW - Softwarentwicklung Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Crott, Anne T1 - Textil- und Industriemuseum (TIM) Augsburg : Entwicklung eines neuen Erscheinungsbildes N2 - Die Stadt Augsburg war eine der größten Textilstädte Europas. Seit 2010 präsentiert das Textil- und Industriemuseum (TIM) eine Vielzahl von Exponaten in der alten Kammgarnspinnerei im ehemaligen Augsburger Textilviertel und ist somit ein wichtiger Bestandteil der bayrischen Museumslandschaft und deutschen Textilgeschichte. Neben seiner besonderen Lage überzeugt das TIM vor allem mit einer großen Musterbuchsammlung. Im Fokus des in dieser Arbeit neugestalteten Erscheinungsbildes stehen die verschiedenen Muster, die den textilen Schwerpunkt in den Vordergrund rücken und dem Museum damit einen einprägsamen Wiedererkennungswert geben. Mithilfe des neuen Corporate Designs soll das Museum für regionale und überregionale Besucher:innen attraktiver gemacht und somit die einmalige geschichtliche Bedeutung vermittelt und erhalten werden. KW - Corporate Design KW - TIM KW - Mode KW - Textil KW - Augsburg Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Christiani, Fabian T1 - Nachhaltiger Bauen : eine interaktive Plattform zum Vergleich von Baustoffen N2 - Bei dem Projekt „Nachhaltiger Bauen – Eine interaktive Plattform zum Vergleich von Baustoffen“ handelt es sich um eine Datenbank, die verschiedene Baustoffe mit deren Eigenschaften listet und einen Vergleich dieser ermöglicht. Das Baugewerbe trägt einen erheblichen Teil zum Klimawandel bei. Besonders der CO2-Ausstoß, der Ressourcenverbrauch und die Abfallproduktion sind hier zu nennen. Deshalb ist der Aspekt der Nachhaltigkeit von zentraler Bedeutung für die Zukunft der Baubranche.Ziel des Projekts ist es, sowohl die technischen als auch die ökologischen Eigenschaften von Baustoffen darzustellen und miteinander zu vergleichen. So kann die Plattform aktiv und effektiv gegen die umwelttechnischen Probleme der Baubranche wirken. KW - Nachhaltigkeit KW - Bauwesen KW - Baustoffe KW - Zukunft KW - Ökologie Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Atlioglu, Dennis T1 - Live it up : eine digitale Plattform für die Live–Veranstaltungsbranche N2 - Mit der App »atmosphere« soll die Veranstaltungsbranche in die digitale Welt eingeführt werden. Insbesondere nach der COVID–19 Pandemie bedarf es einer Erneuerung in dem Sektor für Liveunterhaltung. Die Auswirkungen der Krise auf diesen Wirtschaftszweig waren enorm und auch das Publikum litt unter der Situation. Die Mission von »atmosphere« besteht darin, den Zugang zu Veranstaltungen, Konzerten, Stand–Up–Auftritten und Festivals zu vereinfachen. Hierbei werden die Bereiche der Planung und der Buchung komplett in dem Service der App abgedeckt und die digitale Teilnahme an einem Event ermöglicht. Dies bietet neue Möglichkeiten für die Zukunft und dient als Alternative für Krisen. Insgesamt soll der Service den Zugang vereinfachen, die aufwendigen Planungsschritte reduzieren und die Knackpunkte in der Nutzererfahrung digitalisieren. KW - Veranstaltung KW - Konzert KW - Auftritt KW - Stand–Up–Comedy KW - App Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Franca, Erma T1 - Cai : eine Orientierungshilfe für Geflüchtete und Migrant*innen in Deutschland N2 - Migration und Integration sind weltweit zwei allseits aktuelle Themen. Umso wichtiger ist es, die Ankunft und Integration von Migrant:innen und Geflüchteten so anschaulich wie nur möglich zu gestalten. Die Zielsetzung der Arbeit „Cai – Your guide through Germany“ ist es eine digitale Anwendung in Form einer App zu konzipieren, die Geflüchtete und Migrant:innen in Deutschland während des Migrations- und Integrationsprozesses unterstützt. Dies gelingt durch das strukturierte und themenspezifische Herantragen von notwendigen Informationen, Organisation sowie Selbsthilfeangeboten an die unterschiedlichen Zielgruppen. Unter der Berücksichtigung des Migrationsgrundes und des Standortes wird eine Ausgangssituation geschaffen mit individuellen Bedürfnissen und Fragen, die es zu beantworten gilt. Während Nutzer:innen durch „Cai“ digital, selbstständig und schnell an Informationen gelangen, werden gleichzeitig Behörden und Anlaufstellen sowie ihre Leistungen und Schwerpunkte aufgeführt, die Betroffene bei weiteren Anliegen aufsuchen können, um Unterstützung zu erhalten. Im Rahmen dieser Bachelorarbeit fokussiert sich das Projekt auf die Migrationsgruppe der Geflüchteten sowie ihre Fragen, Herausforderungen und Bedürfnisse in Deutschland. KW - Migration KW - Integration KW - Flucht KW - Geflüchtete KW - Migrationsgruppe Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Switalla, Justin T1 - Applause : Entwicklung eines Dokumentationssystems für die stationäre Altenpflege - Konzeption einer zukunftsgewandten Dokumentationslösung N2 - Der Personalmangel in der Pflege ist vor allem durch die Pandemie in den Fokus der Öffentlichkeit gerückt. Diese Situation wird sich in den nächsten Jahren aufgrund der steigenden Pflegequote in Folge des demografischen Wandels weiter zuspitzen. Das Dokumentieren der durchgeführten Tätigkeiten nimmt dabei viel Zeit in Anspruch, die nicht den Bewohner:innen zugutekommt. Das Dokumentationssystem „Applause“ soll Pflege- und Betreuungskräfte in ihrer Arbeit unterstützen und durch die einfache Nutzerführung den Schulungsaufwand reduzieren. Durch die Integration von modernen medizinischen Sensoren kann innerhalb des Systems der aktuelle Gesundheitsstatus der Bewohner:innen eingesehen werden. Zusätzlich wird die interne sowie externe Kommunikation innerhalb des Dokumentationssystems abgebildet. Bei Letzterer wird mittels einer datenschutzkonformen Software die auf Fax basierende Kommunikation abgelöst. KW - Pflegekräftemangel KW - Dokumentationssystem KW - Pflegekräfte KW - Gesundheit Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Theis, Alina Naomi T1 - Nur ein Freitag : Ein Kurzfilm über Verlust und Freundschaft im Schatten des Zweiten Weltkrieges. N2 - Der Film zeigt die wahre Geschichte des 15-jährigen Hans Jokisch, welche auf den Erzählungen seiner jüngeren Schwester, der Zeitzeugin Maria Theis (geb. Jokisch), beruhen. Der Fokus liegt auf der Sichtweise von Kindern und Jugendlichen, einer Generation, die mit dem und im Zweiten Weltkrieg aufgewachsen ist und die gleichzeitig die letzte Generation ist, die uns das Erlebte noch aus erster Hand berichten kann. Hans gelangt mit seiner Familie nach einer harten Flucht vor der Frontlinie zurück in seine Heimat in Schlesien. Doch ihr geliebtes Heim ist besetzt von Familie Schöppe. Sie haben keine Wahl, die beiden Familien müssen sich das Haus von nun an teilen. Im Laufe der Zeit wird das Jokisch Haus auch für Familie Schöppe ein Zuhause und Hans freundet sich mit dem Jungen Bruno Schöppe an. Als Deutschland 1945 kapituliert und Schlesien nun zu Polen gehört, müssen plötzlich beide Familien endgültig das Haus und all ihren Besitz zurücklassen. Hans und Bruno beschließen, die Zwangsenteignung nicht hinzunehmen, doch ihr naiver Plan wird ihnen fast zum Verhängnis. KW - Zeitzeugen KW - historisches Drama KW - zweiter Weltkrieg KW - WW2 KW - Filmproduktion Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Treutlein, Antonia T1 - Entwicklung eines Erscheinungsbildes für die Meeresschutzorganisation Ocean Care N2 - Ocean Care ist eine politisch unabhängige Non-Profit-Organisation mit Sitz in der Schweiz. Sie setzt sich seit 1989 für den Schutz von Meeressäugern und deren Lebensraum ein. Seit 2011 ist Ocean Care außerdem UN-Sonderberaterin für Fragen im Meeresschutz. Da Ocean Care die Öffentlichkeit für das Thema Meeresschutz sensibilisieren möchte und ihre Arbeit durch Spenden finanziert wird, ist ein professionelles, vertrauenerweckendes Erscheinungsbild unerlässlich. Durch ein zeitgemäßes und seriöses Design, welches sich von anderen Organisationen abhebt, kann die Zielgruppe erweitert und die Bedeutsamkeit der Arbeit hervorgehoben werden. Das neue Erscheinungsbild beruht auf der Idee, dass sich die Informationen unter der Meeresoberfläche befinden. Die Linie, die den Meeresspiegel visualisiert, dient außerdem medienübergreifend als Orientierungshilfe. KW - Erscheinungsbild KW - Gestaltung KW - Corporate Design KW - Layout KW - Redesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vasevska, Ivana T1 - FEEL IT_HEAL IT - the process of healing repressed emotions N2 - Unsere Emotionen beeinflussen die Art und Weise, wie wir mit uns selbst und der Welt um uns herum umgehen. Sie wirken sich auf unsere geistige und körperliche Gesundheit aus. Da einige unserer Emotionen als „schlecht“ oder „negativ“ wahrgenommen werden, erlauben wir uns oft nicht, sie zu fühlen, und wir unterdrücken sie. Ziel dieses Projekts ist es, mithilfe von Fotografie und Grafik zu zeigen, wie man mit unangenehmen und so genannten „negativen“ Emotionen umgehen kann. Der Schwerpunkt liegt gleichermaßen auf dem konzeptionellen und kreativen Teil. Dabei wurden ein Modell und wechselnde Farblichter verwendet, um die emotionalen Zustände einer Person darzustellen, die diese Transformation durchläuft. Ein weiteres Ziel ist es, die Bedeutung eines bewussteren Umgangs mit unseren Emotionen zu betonen. Das Endmedium ist ein Fotobuch inkl. Piktogramme, die die fünf Stadien repräsentieren: Leiden, Bewusstsein, Konfrontation, Ausdruck und Akzeptanz. (Suffering, Awareness, Confrontation, Expression and Acceptance). KW - Emotionen KW - Integration KW - Verdrängung KW - Heilung KW - Emotionaler Schmerz Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Victoria, Jacqueline T1 - IN BETWEEN : An attempt to capture emotions N2 - Emotionen durchlebt jeder Mensch. Von unserer Geburt bis zu unserem Tod. Der Psychologe Paul Eckman hat sechs grundlegende Emotionen identifiziert. Glück, Traurigkeit, Ekel, Angst, Überraschung und Wut. Emotionen können in positive und negative, aber auch in die weniger beachtete neutrale Emotion unterteilt werden. Emotionen werden ständig und wechselnd erlebt und sind deshalb vorstellbar als "Spektrum" oder als "Unendlichkeitschleife". Wie Menschen Emotionen erfahren, ist unterschiedlich. Sie sind abstrakt. Das Fotobuch "In Between" will das Emotionsspektrum und das Abstrakte mithilfe einer Kurzgeschichte sichtbar machen. Das Editorial und die fotografische Gestaltung greifen das Konzept der endlosen Schleife unserer Gefühlswelt auf und machen sie erlebbar. KW - Fotografie KW - Fotobuch KW - Emotion KW - Endlosschleife KW - Candid Fotografie Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - vom Endt, Ksenia T1 - MIR : 11 Kinder, 25 Sprachen und eine Welt - Graphic Novel über bilinguale Kinder N2 - Durch die zunehmende Globalisierung und Immigration steigt auch weltweit die Anzahl der Kinder, die mit mehr als einer Sprache aufwachsen. Dies kann für sie in vielerlei Hinsicht wichtig und förderlich sein. In der Graphic Novel „MIR“ wird in zehn Geschichten gezeigt, welche unterschiedlichen Formen von Bilingualismus es gibt, welche Vor- und Nachteile es hat, bilingual aufzuwachsen und wie es sich auf das Alltagsleben der Kinder und der ganzen Familie auswirkt. Die Geschichten sind realen Erlebnissen nachempfunden, die durch Interviews gesammelt wurden und illustrativ dargestellt sind. Mehrsprachigkeit ist weder ein Privileg noch ein Problem. Sprache ist zuallererst Kommunikation, und es ist wichtig, dass sie überhaupt stattfindet. KW - Graphic Novel KW - Illustration KW - Comic KW - Bilingual KW - Kinder Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wetzlar, Jana T1 - Vielgut Festival 2022 : Etablierung eines neuen Musikfestivals in Aachen N2 - Endlich! Nach über zwei Jahren kulturellen Stillstands richtet der Musiknetzwerk Aachen e.V. ein Festival aus. Die Bachelorandin Jana Wetzlar übernimmt hierbei die Veranstaltungsplanung und -bewerbung. Der erste Teil der Arbeit umfasst die Erarbeitung eines einzigartigen Festivalkonzepts, bei dem die Förderung von jungen Newcomerkünstler:innen und die ökologische Nachhaltigkeit der Veranstaltung im Vordergrund stehen. Eine weitere Besonderheit stellt das paritätisch besetzte Künstler:innen-Line-Up dar. Im zweiten Teil der Arbeit wurden eine umfangreiche Werbekampagne sowie ein passendes Corporate Design entwickelt, die die Besonderheiten des Festivals hervorheben und viele Festivalbesucher:innen generieren sollen. Die übergeordneten Ziele der Arbeit bestehen darin, einen Beitrag zur gesellschaftlichen Etablierung des Musiknetzwerk Aachen e.V. zu leisten und die Voraussetzungen für ein jährlich wiederkehrendes Festival zu schaffen. KW - Festival KW - Musik KW - Veranstaltung KW - Kampagne KW - Marketing Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wojcieszak, Marc David T1 - Da Capo - The Town of Music N2 - In dem Film geht es um die Musikstadt "Da Capo", in der jedes Genre sein eigenes Viertel hat. Unser Protagonist wurde im falschen Viertel geboren und muss sich nun heraus musizieren. KW - Musik KW - Film KW - Stadtviertel KW - Genre KW - musizieren Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wolf, Nina T1 - Koexistieren : Die Stufen der Mensch-Tier-Beziehung – Vom Nutztier bis zum Personenrecht N2 - Seit 2002 ist der Tierschutz fest im Grundgesetz verankert, jedoch herrscht immer noch ein enormes Ungleichgewicht bei der letztendlichen Durchsetzung gegenüber der Tiernutzungsinteressen. Die Nichteinhaltung des Tierschutzes stellt nicht nur aus Tierwohlsicht, sondern auch aus Klimaschutzgründen eine ernst zu nehmende Problematik dar, welche wir nur gemeinsam angehen können. Die Gesellschaft sollte sich über das eigene Konsumverhalten bewusst werden, gleichermaßen müssen auch überzeugende Alternativen aufgezeigt werden. Thematisch ist die Arbeit in drei Teile gegliedert. Die Geschichte, das Recht der Tiere und die Zukunftsaussichten stehen hier im Fokus. Wichtig ist es, den Istzustand neutral darzustellen, um die Fakten nicht zu harmonisieren. Die Publikation soll nicht abschrecken, vielmehr soll sie die Leser:innen motivieren, Dinge ändern zu wollen. Denn nur miteinander können wir friedlich „koexistieren“. KW - Koexistenz KW - Tierschutz KW - Nutztier KW - Kultur KW - Gesellschaft Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wolters, Marina T1 - Zeitfenster : Prototyp einer animierten Installation zum Thema Mesokosmos und Lebensraum Erde N2 - Der Prototyp des Projekts "Zeitfenster" stellt eine Installation dar, inspiriert vom Museum für Naturkunde Berlin. Die Installation besteht aus einer Animation, die an die Fenster des Dinosauriersaals im Museum pojiziert wird. Die Animation zeigt in einer Art Zeitreise, wie das Erbe der Natur aussieht und was der Mensch daraus macht. In der Zeit des Klimawandels setzt sich Design vermehrt für die Aufklärung des Naturschutzes ein. Die Animation soll die Zuschauer, ob Jung oder Alt, für die Verbindung zwischen dem Menschen und der Erde sensibilisieren. Dies wird erreicht, indem sich die Installation die atemberaubende Atmosphäre des Dinosauriersaals zu Nutze macht. Die Fenster des Saals erlauben es, die Bildnisse in beeindruckender Lebensgröße darzustellen. Im Fokus steht, dass der Prototyp ein Erlebnis konzipiert, welches nur durch das Zusammenspiel der verschiedenen Medien möglich ist. KW - Animation KW - Animationsfilm KW - Installation KW - Museum KW - Natur Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Freh, Katharine T1 - The Distance : ein dystpischer Kurzfilm N2 - "THE DISTANCE" ist ein fiktionaler, dystopischer Kurzfilm, welcher sich mit dem Leben in einem diktatorischen Polizeistaat auseinandersetzt. Jegliche Art von Aufstand oder negativer Äußerung dem Staat gegenüber ist untersagt und wird hoch bestraft. Ziel dieser Arbeit ist es, die Zuschauer:innen zum Denken und zum Hinterfragen gesellschaftlicher Strukturen anzuregen. Durch passende Kostüme, Locations und Set-Design entsteht eine düstere und unbehagliche Atmosphäre. Die passende Musik und das Sounddesign unterstützen diese Atmosphäre und geben den Zuschauer:innen einen guten Einblick in diese neue Welt. Zuletzt stellt sich die Frage, ob Dystopien überhaupt noch fiktional sind oder doch schon zu unserer Realität geworden sind. KW - Dystopie KW - Kurzfilm KW - Zukunft KW - Gesellschaftskritik Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Frohn, Paul T1 - Intrinsische Raster N2 - Das Projekt »Intrinsische Raster« erforscht Raster für Webseiten, beginnend mit Untersuchungen aus dem Bereich Print bis hin zu intrinsischen Rastern im Web. Die Entwicklung des Rasters ist von dem Bereich Print geprägt. Heute ist das Medium digital und responsiv. Das Raster wird im CSS definiert und verändert sich intrinsisch in allen Formatgrößen. »Intrinsisch« beschreibt hier die neue Stufe von programmierbaren Rastern im Webdesign, welche Spalten und Module nach vordefinierten Parametern verändert. Variable Fonts verfügen über individuelle Parameter und werden in dem Projekt als Color Fonts in Raster integriert. Im Zentrum steht die Weiterentwicklung der Designprofession, um Raster für zukünftige Anwendungen vorzubereiten. KW - Raster KW - Rastersysteme KW - Webdesign KW - Designwissenschaften KW - Typografie Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Gehrig, Jana T1 - Gynaika - Ungleichbehandlung ist besser N2 - „Gynaika“ – ist griechisch und bedeutet Frau, Frausein. Das Frausein stellt besonders in der Medizin und der Forschung ein Problem dar. Ihre Gesundheit leidet unter der Gleichbehandlung in der Medizin, da die Beschwerden von Frauen zu häufig nicht beachtet werden und undiagnostiziert bleiben. Das medizinisch fundierte Magazin ""Gynaika"" soll über Erkrankungen bei Frauen aufklären, die Leser:innen zu einer Diagnose und guten Behandlung verhelfen. Beschreibung der Erkrankung, Erklärungen zum Ablauf im Körper und Behandlungsmöglichkeiten stehen neben neusten Studien und Erfahrungen von Betroffenen an erster Stelle. Die Informationen werden durch erklärende Einschübe sowie anschauliche Illustrationen und Grafiken begleitet. Ziel ist es, mehr Aufmerksamkeit auf die Notwendigkeit einer Ungleichbehandlung der Geschlechter in der Medizin zu ziehen. KW - Illustration KW - Editorial KW - Informationsvisualisierung KW - Magazin KW - Frauengesundheit Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ihl, Andrea T1 - Sehen und gesehen werden: Eine Darstellung (post-)migrantischer Perspektiven N2 - In einer Welt, definiert durch Grenzziehungen, ist es vor allem für diejenigen schwer, ihren Platz zu finden, die bereits über diese hinauswachsen mussten. Denn Migration bedeutet nicht nur, eine Strecke über eine ländliche Linie hinter sich zu bringen. Oft werden die komplexen emotionalen Facetten dieser permanenten Überquerung vergessen, die über Generationen ihre Spuren hinterlassen. Was bedeutet es, ein Leben ganz von neu aufbauen zu müssen, wenn man bereits eins hinter sich gelassen hat? Wieso verspüren wir Sehnsucht nach einer Heimat, die es so gar nicht geben kann? Und wann haben wir das Gefühl, endlich angekommen zu sein? Über diese und viele weitere Fragen wird in »Mesta« zusammen mit (Post-)Migrant:innen reflektiert, die intensiv ihre Erfahrungen teilen. Ziel der Publikation ist das, was meistens vernachlässigt wird: einfach zuzuhören. KW - Illustration KW - Editorialdesign KW - Interview KW - Print KW - Postmigrantisch Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ioannidou, Martha T1 - Master of Procrastination N2 - In den letzten Jahren ist das Thema “Prokrastinieren” omnipräsent geworden. Gegensätzlich dazu versuchen immer mehr Menschen sich zu optimieren. Ziel dieser Arbeit ergibt sich in der Verbindung dieser paradoxen Vorgänge. Im Video wird nicht nur der Begriff Prokrastinieren erklärt, sondern auch ein faktisch basierter Leitfaden zum verbesserten Aufschieben präsentiert. Der Zuschauer kann sich in humoristisch und ironischer Art mit der Thematik auseinandersetzten, Ohne sich mit der negativen Konnotation zu beschäftigen. “Master of Procrastination” eröffnet einen neuen Blickwinkel und informierten Gleichermaßen zu einer unbeliebten Problematik. KW - Prokrastinieren KW - Aufschieben KW - Aufschieberitis KW - Machichmorgen KW - Leitfaden Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Koscielniak, Luise T1 - Das Ludwig Forum Aachen : die Erstellung eines neuen Erscheinungsbildes N2 - Peter und Irene Ludwig galten als das Kunstsammlerpaar Deutschlands. Sie stellten ihre umfangreiche Sammlung der Öffentlichkeit zur Verfügung, so auch dem Ludwig Forum - das Stammmuseum der beiden Aachener. Doch es ist viel mehr als nur ein Museum. Der Gedanke des Forums als einen Ort des Austausches und der Kommunikation mit und über Kunst ist die leittragende Idee. Das neue Erscheinungsbild leitet sich in der Gestaltung bildlich von diesem Forumsgedanken ab. Zur Visualisierung dieser Idee wurden Kommunikationsachsen aufgegriffen, die zur typografischen Ausrichtung genutzt werden. Sie bieten die Möglichkeit, in verschiedene Richtungen zu kommunizieren und Inhalte vielseitig und prägnant zu visualisieren. Die Wortmarke des Ludwig Forums dient dabei als klammerndes Element, welches den Rahmen für die Gestaltung ermöglichen. Mit der Fokussierung auf den Forumsgedanken setzt sich das Ludwig Forum sowohl inhaltlich als nun auch gestalterisch von anderen Museumseinrichtungen ab. KW - Erscheinungsbild KW - Ludwig Forum KW - Forum KW - Kommunikation KW - Dialog Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Larscheid, Maja Marlene T1 - The Future of Fitness : Konzeption und Gestaltung einer digitalen Fitness- und Gesundheitsanwendung N2 - Laut einer Langzeitstudie bewegt sich mehr als ein Viertel der Weltbevölkerung – rund 2 Milliarden Menschen – zu wenig. Trotzdem ließ sich zuletzt klares Interesse an Fitness- und Gesundheitsmöglichkeiten am stetigen Anstieg der Fitnessstudio-Mitgliederzahl erkennen. Nachdem die Zahl seit 2006 jedes Jahr anstieg, fiel sie in den Pandemie-Jahren. Seit der Pandemie besteht also Bedarf nach einer flexibleren Lösung zu klassischen Studios. Um diesen Bedarf zu decken, wurde eine digitale Lösung zum Thema entwickelt. Dazu wurden Sport und Ernährung zusammengefasst. Das beinhaltet Videoanleitungen, Ernährungs- und Trainingsplanerstellung, individuelle Körperanalyse im Onboarding-Prozess, Verbindung mit Wearables und ein flexibles Online- sowie Studioangebot. Meine Zielgruppe sind Menschen, die flexibel Sport machen, mit Sport anfangen oder ihre allgemeine Gesundheit verbessern wollen. KW - Fitness KW - Gesundheit KW - Ernährung KW - Sport KW - UXDesign Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Laubkermeier, Kim T1 - trust me N2 - "trust me" ist eine schwarz-weiß Fotoserie, präsentiert als Diashow mit unterlegtem Soundtrack. Es geht um das Vertrauen zwischen Model, Fotografin und Betrachter:innen. Die Darsteller sind ausschließlich homosexuelle Männer und begeben sich in intime Situationen und Posen. Die Fotos sind überwiegend Aktaufnahmen und nehmen eine pornografische Richtung an. Die Fragestellung zu Beginn war, wie weit vertrauen die unerfahrenen Models der Fotografin und was sind diese bereit, von sich zu zeigen. Die offene Kommunikation über die Richtung des Projekts war die essenzielle Basis für die Fotoshootings. Während des Fotografierens lag der Fokus auf möglichst verschiedenen Blickwinkeln, Kulissen, Ausleuchtungen und Motiven. Zusätzlich war der sensible Umgang mit den Männern eine Vertrauensprobe."trust me" lässt auf diversen Ebenen tief blicken und zeigt, wie loslassen aussieht. KW - Fotografie KW - schwarz-weiß KW - Diashow KW - Vertrauen KW - Portraits Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Alt, Helmut T1 - Speicher speichern, Leiter leiten T2 - Generationenprojekt Energiewende : Elektroenergiepolitik im Spannungsfeld zwischen Vision und Mission / Herbert Niederhausen (Hrsg.) Y1 - 2022 SN - 9783755774389 N1 - gedruckt in der Bereichsbibliothek Eupener Str. unter der Signatur 21 ZPM 4 SP - 125 EP - 136 PB - Books on Demand CY - Norderstedt ER - TY - JOUR A1 - Uysal, Karya A1 - Creutz, Till A1 - Firat, Ipek Seda A1 - Artmann, Gerhard A1 - Teusch, Nicole A1 - Temiz Artmann, Aysegül T1 - Bio-functionalized ultra-thin, large-area and waterproof silicone membranes for biomechanical cellular loading and compliance experiments JF - Polymers N2 - Biocompatibility, flexibility and durability make polydimethylsiloxane (PDMS) membranes top candidates in biomedical applications. CellDrum technology uses large area, <10 µm thin membranes as mechanical stress sensors of thin cell layers. For this to be successful, the properties (thickness, temperature, dust, wrinkles, etc.) must be precisely controlled. The following parameters of membrane fabrication by means of the Floating-on-Water (FoW) method were investigated: (1) PDMS volume, (2) ambient temperature, (3) membrane deflection and (4) membrane mechanical compliance. Significant differences were found between all PDMS volumes and thicknesses tested (p < 0.01). They also differed from the calculated values. At room temperatures between 22 and 26 °C, significant differences in average thickness values were found, as well as a continuous decrease in thicknesses within a 4 °C temperature elevation. No correlation was found between the membrane thickness groups (between 3–4 µm) in terms of deflection and compliance. We successfully present a fabrication method for thin bio-functionalized membranes in conjunction with a four-step quality management system. The results highlight the importance of tight regulation of production parameters through quality control. The use of membranes described here could also become the basis for material testing on thin, viscous layers such as polymers, dyes and adhesives, which goes far beyond biological applications. Y1 - 2022 SN - 2073-4360 VL - 14 IS - 11 SP - 2213 PB - MDPI CY - Basel ER - TY - THES A1 - Lenz, Lena T1 - Frauen sind der Boss : eine Kampagne für mehr Gleichberechtigung in Führungspositionen N2 - Man könnte vermuten, dass in einem so weit entwickelten Land wie Deutschland Geschlechterdiskriminierung bereits erfolgreich überwunden wurde – doch das entspricht nicht der Realität. Besonders in Führungspositionen fällt dieses Ungleichgewicht auf. Eine Ursache dafür ist das historisch etablierte Rollenverständnis, aber auch vonseiten der Frauen gibt es häufig ein grundlegendes Problem: Sie trauen sich zu wenig zu. Die Kampagne soll junge Frauen dazu motivieren, ihre beruflichen Ambitionen hoch anzusetzen und zielstrebig zu verfolgen. Das Online-Portal "femiverse" ist dabei ihr Wegbereiter. Es ermöglicht einen direkten Austausch mit anderen Nutzer:innen und eröffnet durch Workshops mit Unternehmer:innen neue Perspektiven. Die Bezeichnung „Powerfrau“ ist überholt – Frauen in Führungspositionen sind keine Ausnahmetalente, sie sind die Normalität von morgen. KW - Kampagne KW - Geschlechtergerechtigkeit KW - Gleichberechtigung KW - Frauen KW - Beruf Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Nelles, Charlene T1 - Brain Hack N2 - Protagonistin des Films ist Cassandra Becker, eine 25-jährige Informatikstudentin und Mitglied der Hackerorganisation PFABW (Progress For a Better World). Sie hat es sich zum Ziel gesetzt, die Welt zu einem besseren Ort zu machen. Sie legt sich allerdings mit den falschen Leuten an und wird für die Verbreitung eines zerstörerischen Computervirus verantwortlich gemacht, der gesundheitliche Folgen für den Menschen mit sich bringt. Sie und ihr bester Freund Jake Fischer haben bei einem PFABW-Mitglied Zuflucht gefunden. Dort versuchen sie gemeinsam herauszufinden, was es mit dem mysteriösen Virus auf sich hat. KW - Freundschaft KW - Schuld KW - Liebe KW - IT KW - Hacker Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Neumann, Julius T1 - Traces of urban change N2 - Eine Stadt ist das Ergebnis eines komplexen Urbanisierungsprozesses. Dieser ist vor allem dadurch bestimmt, dass immer mehr Menschen in Städten leben. Das Wachstum und Altern von Städten machen ständige räumliche und bauliche Veränderungen erforderlich. Die Bachelorarbeit verdeutlicht diese strukturellen Veränderungen der Stadt Aachen anhand von analogen Fotografien im Jahr 2022. Dabei werden Spuren aus unterschiedlichen Zeiten betrachtet und natürliche oder durch den Menschen beeinflusste Veränderungen in Form von Verfall, Nutzung und Erneuerung aufgezeigt. Ziel ist es, den Blick auf Details des urbanen Wandels zu richten, um diesen wahrnehmbar und bewusst zu machen. Die Betrachter:innen sollen zum Nachdenken und genauen Hinschauen angeregt werden. Die Fotografien versuchen den zurückliegenden Veränderungsprozess erkennen zu lassen und damit gewissermaßen dessen Geschichte abzubilden. KW - Fotografie KW - analog KW - Bildband KW - Aachen KW - Stadt Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Pauly, Tim Christian T1 - Fantasy : Die Gefahren des Internets und der Sozialen Medien in Bezug auf Kinder N2 - Anhand der Geschichte des Protagonisten Max, wird auf die Gefahr des Internets und der Sozialen Medien hinsichtlich Kinder aufmerksam gemacht. Kinder sind im Internet einigen Gefahren ausgesetzt und ihre Eltern sind sich dessen oftmals kaum bewusst oder haben Probleme, das Tun der Kinder im Auge zu behalten. Die Geschichte wird durch die Lyrik eines Liedes erzählt. Im dazugehörigen Musikvideo bekommen die Zuschauer:innen einen Einblick in Max Leben und sein Leid. Des Weiteren ist zu sehen, wie Max den Täter verurteilt, seine Fantasie gestohlen zu haben. Unklar bleibt, ob sein Auftreten währenddessen in der Wirklichkeit oder aus seiner verbliebenen Fantasie heraus passiert. Sein schweres Schicksal, ausgedrückt mit aller Härte, soll den Zuschauenden schockierend auf die Problematik aufmerksam machen. Das Projekt soll helfen, diese fehlende Aufmerksamkeit einzudämmen. KW - Fantasie KW - Internet KW - Soziale Medien KW - Missbrauch KW - Bedrohung Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Koenen, Rachel A1 - Pohlen, Britta T1 - Energie zur Teilhabe : Etablierung einer Plattform zum Ausbau der Energiewende für städtische Mieter N2 - Die gelungene Energiewende ist essenziell auf dem Weg zur geplanten Klimaneutralität bis 2045. Möglichkeiten für Immobilienbesitzer:innen, sich am Ausbau erneuerbarer Energien zu beteiligen, sind überwiegend bekannt. Mieter:innen im urbanen Raum werden jedoch nicht adäquat darüber aufgeklärt, wie auch sie teilhaben können. Die Online-Plattform „energiewende-teilhaben.de"" zentriert Wissen und schlägt konkrete personalisierte Maßnahmen zur Partizipation vor. Eine Werbekampagne etabliert die Plattform im städtischen Raum und zeigt bereits motivierten Mieter:innen einfache Möglichkeiten zur Beteiligung auf. Durch eine hohe Sichtbarkeit der wachsenden Community werden noch Unbeteiligte angesteckt und die Wende in der Stadt ausgelöst. Die Kampagne lenkt die Motivationsenergie der Bevölkerung über die Plattform auf Teilhabe und Klimaschutz. KW - Energiewende KW - erneuerbare Energien KW - Strom KW - Stadt KW - Mieter Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Kurz, Melanie A1 - Schwer, Thilo T1 - Geschichte des Designs N2 - Dieser Band bietet einen kompakten Überblick über die wichtigsten Stationen des Produktdesigns vom Beginn der Industrialisierung bis heute. Im Zentrum stehen ikonische Alltagsgegenstände vom Thonet-Stuhl bis zum iPhone. Anschaulich und kenntnisreich nehmen Melanie Kurz und Thilo Schwer dabei auch die gesellschaftspolitische Situation, in der die Objekte entstanden sind, in den Blick. Y1 - 2022 SN - 978-3-406-78813-0 PB - Beck CY - München ET - 1. Auflage ER - TY - THES A1 - Puzich, Simon T1 - komuniiio : Generationenaustausch & Engagement neu gedacht N2 - Aktuelle Ehrenämter und Möglichkeiten des Austauschs sind in alten Strukturen festgefahren und erfahren wenig Aufmerksamkeit. Die Potenziale von älteren Generationen werden zu selten geschätzt und ausgeschöpft. Dazu werden Sie in vielen neuen Dingen und Anwendungen nicht als Nutzer:innengruppe beachtet und somit Schritt für Schritt ausgegrenzt. Der Ansatz dieser Arbeit war es, eine gesellschaftlich fördernde digitale Oberfläche für den Generationenaustausch zwischen jung und alt zu schaffen - unabhängig von Vereinsstrukturen oder Organisationen. Vereinen wir das Bewusstsein der Alten mit der Neugier und Innovationskraft der Jungen, um eine Zukunft zu schaffen, in der es sich lohnt, jung zu sein, als auch alt zu werden. KW - Generationenaustausch KW - Accessability KW - Inklusion KW - Community KW - Sozial Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Roentgen, Matthis T1 - Ketten, die die Welt umspannen : wie funktioniert Blockchain-Technologie und was kann sie uns bieten? N2 - Bitcoins und NFTs sind längst keine Neuheit mehr und vielen bereits ein Begriff. Doch was genau steckt hinter digitalen Währungen und kryptografischen Tokens? »Ketten, die die Welt umspannen« ist die erste Ausgabe des »101.mag« und setzt sich mit dieser Frage auseinander. Das Magazin versucht über ein unkonventionelles Layout, interessante Artikel und spannende Illustrationen seine Leser:innen in die Welt der vielversprechenden Technologie einzuführen. Die Kommunikationen zwischen Mensch und Computer steht nicht nur thematisch im Mittelpunkt dieser Arbeit. Auch die Gestaltung profitiert von dieser Zusammenarbeit. So wurde der Fließtext mithilfe eines Processing-Tools über das Raster verteilt. Auch die Illustration wurde über ein weiteres Programm in verpixelte Grafiken umgewandelt. Die statischen Bild- und Textelemente werden durch kleine Animationen ergänzt. Diese werden im digitalen Raum eingesetzt und unterstützen so das gesamte Konzept auf multimedialer Ebene. Das Ergebnis ist ein besonderes Magazin, welches eine neue Richtung einschlägt. KW - Editorial KW - generische Gestaltung KW - Layout KW - Magazin KW - Blockchain Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schiffers, Simon T1 - Historische Stoffe im Spielfilm : Zwischen Authentizität und Unterhaltung N2 - Historische Stoffe im Spielfilm Zwischen Authentizität und Unterhaltung Spielfilme über wahre Begebenheiten stellen sich der Herausforderung, historisch korrekte Darstellung mit einer spannenden und sehenswerten Präsentation zu kombinieren. Dies ist ein schwieriger Balance Akt, gerade bei Studentenprojekten mit geringem Budget. Im Kurzfilm über Julius Erasmus, dem „Totengräber von Vossenack“, wurde sich dieser Aufgabe gestellt. Inhaltlich werden seine möglichen Beweggründe dargestellt, die ihn dazu brachten kurz nach dem 2. Weltkrieg zahlreiche gefallene Soldaten im ehemaligen Kampfgebiet im Hürtgenwald zu begraben. Die schriftliche Dokumentation des Projektes zeigt die Recherche des verfilmten Stoffes, Herausforderungen während der Produktion, sowie persönliche Eindrücke und Lerneffekte. Letztendlich ist ein Werk entstanden, dass respektvoll mit der zu Grunde liegenden Geschichte umgeht und gleichsam ein cineastisches Erlebnis für den Zuschauer darstellt. KW - Kurzfilm KW - Authentizität KW - wahre Begebenheit KW - Vossenack KW - Julius Erasmus Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Schmalfuss, Vanessa Dana T1 - LGBTQIA+ : Aufklärungskampagne für die Reduzierung des Gebrauchs von Schimpfwörtern an Schulen N2 - Der Missbrauch von Schimpfwörtern im Bereich Schule, die sich gegen LGBTQIA+ richten, ist nach wie vor ein ernst zu nehmendes Problem. Durch eine Aufklärungskampagne wird diesem Problem entgegengewirkt. Da man den Schüler:innen das Benutzen von Schimpfwörtern nicht ganz abgewöhnen kann, wird ihnen durch die Kampagne vorgemacht, wie man besser, cooler und intelligenter schimpft. Durch das Motto "Richtig schimpfen ganz unkompliziert" zeigt die Kampagne den Schüler:innen, wie man auf eine smarte Art und Weise mit Worten umgeht und gleichzeitig den eigenen Gebrauch von Schimpfwörtern reflektiert. KW - LGBTQIA+ KW - Aufklärungskampagne KW - Schule KW - Schimpfwörter Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Sehl, Kristina T1 - Adapt or die : Heimische Wälder im Wandel durch Mensch und Zeit N2 - Wo einst fast lückenlos Laubwälder wuchsen, steht heute nur noch ein Drittel der ursprünglichen Waldfläche. Echte Urwälder gibt es hier schon lange nicht mehr: Die Rede ist vom deutschen Wald. Unsere Welt ist im Wandel. Auch in unseren heimischen Wäldern lassen sich die Einflüsse von Mensch und Klimawandel auf die Biodiversität beobachten. Die illustrierte Publikation „Adapt or die“ lädt mit mehr als 80 großformatigen Artenportraits, Habitat-Kartierungen und gestalteten Themenklappenseiten zur Auseinandersetzung mit dem Wandel unserer heimischen Wälder ein. Dabei sensibilisiert sie für einen bewussteren Umgang mit Umwelt und Natur. Erweiterungen durch Augmented Reality bieten vereinzelt neben dem Printprodukt aktualisierbare Prognosen, digital und ressourcenschonend. Das komplexe Ökosystem des Waldes reagiert empfindlich auf Veränderungen: Wer sich nicht anpassen kann, wird verschwinden. KW - Wald KW - Lebensraum KW - Wandel KW - Artenvielfalt KW - Biodiversität Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Steimel, Nina T1 - An den Rand gedrängt : die Marginalisierung unserer Städte N2 - In der Arbeit »An den Rand gedrängt–Die Marginalisierung unserer Städte« wird anhand des Flächenverbrauchs des ruhenden Verkehrs erörtert, inwieweit der private Pkw die Entwicklung unserer Städte bestimmt. Die Zusammenstellung verschiedener Texte, Raumbeobachtungen und fotografischer Zeitdokumente soll die Problematik und Aktualität des Themas verstärken. Schritt für Schritt sollen die Leser:innen einen neuen Blick auf die eigene Stadt gewinnen und für das Problem der akuten Flächenknappheit sensibilisiert werden. Das Werk versteht sich als Aufruf, unseren Straßenraum zu entkarbonisieren, ihn neu zu entdecken und die möglichen Chancen im Wandel zu erkennen. Dabei geht es zunächst nicht um die Aufzählung von Klimaschäden, die Abschaffung von Parkplätzen oder gar des Autos, sondern um die Auswirkungen, die Parkplätze auf unser Leben haben und vor allem um ihr Potenzial für die Zukunft. KW - Parkplatz KW - Raumnot KW - Verkehrswende KW - Autofrei KW - Mobilitätswende Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Surowiec, Julia Andrea T1 - Das wahre Gewicht des Smartphones : eine informative Erfahrung zu den ökologischen Auswirkungen N2 - Das Smartphone gehört zu den innovativsten Geräten unserer Zeit und befindet sich in einem ständigen Wandel, der nach immer mehr Leistung, größeren Displays und besseren Kameras strebt. Mit neuen Modellen, die jährlich auf den Markt kommen und den Milliarden Smartphones, die verkauft werden, entsteht aber nicht nur ein großer Markt voller Angebote, sondern gleichzeitig große Probleme für unsere Umwelt und letztlich auch für uns. Die Smartphone-Industrie schadet massiv unserem Ökosystem. Das Ziel der Arbeit ist die Aufklärung über die Auswirkungen der Smartphone-Industrie. Dafür wurden Visualisierung zu Daten und Prozessen gestaltet, die viele Aspekte des Lebenszyklus des Smartphones mit einbeziehen. Die Betrachter:innen sollen so informativ aufgeklärt werden, ihren eigenen Konsum zu dem Thema überdenken und ein Bewusstsein für ihren Elektronikverbrauch entwickeln. KW - Mobiltelefon KW - Ökonomie KW - Ökologie KW - Rohstoffgewinnung KW - Wegwerfgesellschaft Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Horikawa, Atsushi A1 - Ashikaga, Mitsugu A1 - Yamaguchi, Masato A1 - Ogino, Tomoyuki A1 - Aoki, Shigeki A1 - Wirsum, Manfred A1 - Funke, Harald A1 - Kusterer, Karsten T1 - Combined heat and power supply demonstration of Micro-Mix Hydrogen Combustion Applied to M1A-17 Gas Turbine T2 - Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A) N2 - Kawasaki Heavy Industries, Ltd. (KHI), Aachen University of Applied Sciences, and B&B-AGEMA GmbH have investigated the potential of low NOx micro-mix (MMX) hydrogen combustion and its application to an industrial gas turbine combustor. Engine demonstration tests of a MMX combustor for the M1A-17 gas turbine with a co-generation system were conducted in the hydrogen-fueled power generation plant in Kobe City, Japan. This paper presents the results of the commissioning test and the combined heat and power (CHP) supply demonstration. In the commissioning test, grid interconnection, loading tests and load cut-off tests were successfully conducted. All measurement results satisfied the Japanese environmental regulation values. Dust and soot as well as SOx were not detected. The NOx emissions were below 84 ppmv at 15 % O2. The noise level at the site boundary was below 60 dB. The vibration at the site boundary was below 45 dB. During the combined heat and power supply demonstration, heat and power were supplied to neighboring public facilities with the MMX combustion technology and 100 % hydrogen fuel. The electric power output reached 1800 kW at which the NOx emissions were 72 ppmv at 15 % O2, and 60 %RH. Combustion instabilities were not observed. The gas turbine efficiency was improved by about 1 % compared to a non-premixed type combustor with water injection as NOx reduction method. During a total equivalent operation time of 1040 hours, all combustor parts, the M1A-17 gas turbine as such, and the co-generation system were without any issues. KW - industrial gas turbine KW - combustor development KW - fuels KW - hydrogen KW - emission Y1 - 2022 SN - 978-0-7918-8599-4 U6 - http://dx.doi.org/10.1115/GT2022-81620 N1 - ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition June 13–17, 2022 Rotterdam, Netherlands PB - American Society of Mechanical Engineers CY - Fairfield ER - TY - JOUR A1 - Funke, Harald A1 - Beckmann, Nils T1 - Flexible fuel operation of a Dry-Low-NOx Micromix Combustor with Variable Hydrogen Methane Mixture JF - International Journal of Gas Turbine, Propulsion and Power Systems N2 - The role of hydrogen (H2) as a carbon-free energy carrier is discussed since decades for reducing greenhouse gas emissions. As bridge technology towards a hydrogen-based energy supply, fuel mixtures of natural gas or methane (CH4) and hydrogen are possible. The paper presents the first test results of a low-emission Micromix combustor designed for flexible-fuel operation with variable H2/CH4 mixtures. The numerical and experimental approach for considering variable fuel mixtures instead of recently investigated pure hydrogen is described. In the experimental studies, a first generation FuelFlex Micromix combustor geometry is tested at atmospheric pressure at gas turbine operating conditions corresponding to part- and full-load. The H2/CH4 fuel mixture composition is varied between 57 and 100 vol.% hydrogen content. Despite the challenges flexible-fuel operation poses onto the design of a combustion system, the evaluated FuelFlex Micromix prototype shows a significant low NOx performance Y1 - 2022 SN - 1882-5079 VL - 13 IS - 2 SP - 1 EP - 7 ER - TY - CHAP A1 - Tran, Ngoc Trinh A1 - Trinh, Tu Luc A1 - Dao, Ngoc Tien A1 - Giap, Van Tan A1 - Truong, Manh Khuyen A1 - Dinh, Thuy Ha A1 - Staat, Manfred T1 - Limit and shakedown analysis of structures under random strength T2 - Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training, Hanoi, December 2-3, 2022 N2 - Direct methods comprising limit and shakedown analysis is a branch of computational mechanics. It plays a significant role in mechanical and civil engineering design. The concept of direct method aims to determinate the ultimate load bearing capacity of structures beyond the elastic range. For practical problems, the direct methods lead to nonlinear convex optimization problems with a large number of variables and onstraints. If strength and loading are random quantities, the problem of shakedown analysis is considered as stochastic programming. This paper presents a method so called chance constrained programming, an effective method of stochastic programming, to solve shakedown analysis problem under random condition of strength. In this our investigation, the loading is deterministic, the strength is distributed as normal or lognormal variables. KW - Reliability of structures KW - Stochastic programming KW - Chance constrained programming KW - Shakedown analysis KW - Limit analysis Y1 - 2022 SN - 978-604-357-084-7 SP - 510 EP - 518 PB - Nha xuat ban Khoa hoc tu nhien va Cong nghe (Verlag Naturwissenschaft und Technik) CY - Hanoi ER - TY - CHAP A1 - Milijaš, Aleksa A1 - Šakić, Bogdan A1 - Marinković, Marko A1 - Butenweg, Christoph A1 - Gams, Matija A1 - Klinkel, Sven ED - Arion, Cristian ED - Scupin, Alexandra ED - Ţigănescu, Alexandru T1 - Effects of prior in-plane damage on out-of-plane response of masonry infills with openings T2 - The Third European Conference on Earthquake Engineering and Seismology September 4 – September 9, 2022, Bucharest N2 - Masonry infill walls are the most traditional enclosure system that is still widely used in RC frame buildings all over the world, particularly in seismic active regions. Although infill walls are usually neglected in seismic design, during an earthquake event they are subjected to in-plane and out-of-plane forces that can act separately or simultaneously. Since observations of damage to buildings after recent earthquakes showed detrimental effects of in-plane and out-of-plane load interaction on infill walls, the number of studies that focus on influence of in-plane damage on out-of-plane response has significantly increased. However, most of the xperimental campaigns have considered only solid infills and there is a lack of combined in-plane and out-of-plane experimental tests on masonry infills with openings, although windows and doors strongly affect seismic performance. In this paper, two types of experimental tests on infills with window openings are presented. The first is a pure out-of-plane test and the second one is a sequential in-plane and out-of-plane test aimed at investigating the effects of existing in-plane damage on outof-plane response. Additionally, findings from two tests with similar load procedure that were carried out on fully infilled RC frames in the scope of the same project are used for comparison. Test results clearly show that window opening increased vulnerability of infills to combined seismic actions and that prevention of damage in infills with openings is of the utmost importance for seismic safety. KW - Seismic loading KW - In-plane load KW - Out-of-plane load KW - Interaction KW - Window opening Y1 - 2022 SN - 978-973-100-533-1 SP - 2747 EP - 2756 ER - TY - CHAP A1 - Riga, Evi A1 - Pitilakis, Kyriazis A1 - Butenweg, Christoph A1 - Apostolaki, Stefania A1 - Karatzetzou, Anna ED - Arion, Cristian ED - Scupin, Alexandra ED - Ţigănescu, Alexandru T1 - Investigating the impact of the new European Seismic Hazard Model ESHM20 on the seismic design and safety control of industrial facilities T2 - The Third European Conference on Earthquake Engineering and Seismology September 4 – September 9, 2022, Bucharest N2 - The seismic performance and safety of major European industrial facilities has a global interest for Europe, its citizens and economy. A potential major disaster at an industrial site could affect several countries, probably far beyond the country where it is located. However, the seismic design and safety assessment of these facilities is practically based on national, often outdated seismic hazard assessment studies, due to many reasons, including the absence of a reliable, commonly developed seismic hazard model for whole Europe. This important gap is no more existing, as the 2020 European Seismic Hazard Model ESHM20 was released in December 2021. In this paper we investigate the expected impact of the adoption of ESHM20 on the seismic demand for industrial facilities, through the comparison of the ESHM20 probabilistic hazard at the sites where industrial facilities are located with the respective national and European regulations. The goal of this preliminary work in the framework of Working Group 13 of the European Association for Earthquake Engineering (EAEE), is to identify potential inadequacies in the design and safety control of existing industrial facilities and to highlight the expected impact of the adoption of the new European Seismic Hazard Model on the design of new industrial facilities and the safety assessment of existing ones. KW - ESHM20, industrial facilities KW - seismic hazard KW - seismic design KW - safety control Y1 - 2022 SN - 978-973-100-533-1 SP - 3261 EP - 3270 ER - TY - CHAP A1 - Pütz, Sebastian A1 - Baier, Ralph A1 - Brauner, Philipp A1 - Brillowski, Florian A1 - Dammers, Hannah A1 - Liehner, Luca A1 - Mertens, Alexander A1 - Rodemann, Niklas A1 - Schneider, Sebastian A1 - Schollemann, Alexander A1 - Steuer-Dankert, Linda A1 - Vervier, Luisa A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Nagel, Saskia K. A1 - Piller, Frank T. A1 - Schuh, Günther A1 - Ziefle, Martina A1 - Nitsch, Verena T1 - An interdisciplinary view on humane interfaces for digital shadows in the internet of production T2 - 2022 15th International Conference on Human System Interaction (HSI) N2 - Digital shadows play a central role for the next generation industrial internet, also known as Internet of Production (IoP). However, prior research has not considered systematically how human actors interact with digital shadows, shaping their potential for success. To address this research gap, we assembled an interdisciplinary team of authors from diverse areas of human-centered research to propose and discuss design and research recommendations for the implementation of industrial user interfaces for digital shadows, as they are currently conceptualized for the IoP. Based on the four use cases of decision support systems, knowledge sharing in global production networks, human-robot collaboration, and monitoring employee workload, we derive recommendations for interface design and enhancing workers’ capabilities. This analysis is extended by introducing requirements from the higher-level perspectives of governance and organization. KW - digital twin KW - digital shadow KW - cyber-physical production system KW - human-machine interface Y1 - 2022 SN - 978-1-6654-6823-7 (Print) SN - 978-1-6654-6822-0 (Online) U6 - http://dx.doi.org/10.1109/HSI55341.2022.9869467 SN - 2158-2246 (Print) SN - 2158-2254 (Online) N1 - 15th International Conference on Human System Interaction (HSI), 28-31 July 2022, Melbourne, Australia. PB - IEEE ER - TY - JOUR A1 - Falkenberg, Fabian A1 - Bott, Michael A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - Phylogenetic survey of the subtilase family and a data-mining-based search for new subtilisins from Bacillaceae JF - Frontiers in Microbiology N2 - The subtilase family (S8), a member of the clan SB of serine proteases are ubiquitous in all kingdoms of life and fulfil different physiological functions. Subtilases are divided in several groups and especially subtilisins are of interest as they are used in various industrial sectors. Therefore, we searched for new subtilisin sequences of the family Bacillaceae using a data mining approach. The obtained 1,400 sequences were phylogenetically classified in the context of the subtilase family. This required an updated comprehensive overview of the different groups within this family. To fill this gap, we conducted a phylogenetic survey of the S8 family with characterised holotypes derived from the MEROPS database. The analysis revealed the presence of eight previously uncharacterised groups and 13 subgroups within the S8 family. The sequences that emerged from the data mining with the set filter parameters were mainly assigned to the subtilisin subgroups of true subtilisins, high-alkaline subtilisins, and phylogenetically intermediate subtilisins and represent an excellent source for new subtilisin candidates. Y1 - 2022 U6 - http://dx.doi.org/10.3389/fmicb.2022.1017978 SN - 1664-302X VL - 2022 IS - 13 PB - Frontiers CY - Lausanne ER - TY - JOUR A1 - Haeger, Gerrit A1 - Bongaerts, Johannes A1 - Siegert, Petra T1 - A convenient ninhydrin assay in 96-well format for amino acid-releasing enzymes using an air-stable reagent JF - Analytical Biochemistry N2 - An improved and convenient ninhydrin assay for aminoacylase activity measurements was developed using the commercial EZ Nin™ reagent. Alternative reagents from literature were also evaluated and compared. The addition of DMSO to the reagent enhanced the solubility of Ruhemann's purple (RP). Furthermore, we found that the use of a basic, aqueous buffer enhances stability of RP. An acidic protocol for the quantification of lysine was developed by addition of glacial acetic acid. The assay allows for parallel processing in a 96-well format with measurements microtiter plates. Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.ab.2022.114819 SN - 1096-0309 IS - 624 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Welden, Melanie A1 - Severins, Robin A1 - Poghossian, Arshak A1 - Wege, Christina A1 - Bongaerts, Johannes A1 - Siegert, Petra A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Detection of acetoin and diacetyl by a tobacco mosaic virus-assisted field-effect biosensor JF - Chemosensors N2 - Acetoin and diacetyl have a major impact on the flavor of alcoholic beverages such as wine or beer. Therefore, their measurement is important during the fermentation process. Until now, gas chromatographic techniques have typically been applied; however, these require expensive laboratory equipment and trained staff, and do not allow for online monitoring. In this work, a capacitive electrolyte–insulator–semiconductor sensor modified with tobacco mosaic virus (TMV) particles as enzyme nanocarriers for the detection of acetoin and diacetyl is presented. The enzyme acetoin reductase from Alkalihalobacillus clausii DSM 8716ᵀ is immobilized via biotin–streptavidin affinity, binding to the surface of the TMV particles. The TMV-assisted biosensor is electrochemically characterized by means of leakage–current, capacitance–voltage, and constant capacitance measurements. In this paper, the novel biosensor is studied regarding its sensitivity and long-term stability in buffer solution. Moreover, the TMV-assisted capacitive field-effect sensor is applied for the detection of diacetyl for the first time. The measurement of acetoin and diacetyl with the same sensor setup is demonstrated. Finally, the successive detection of acetoin and diacetyl in buffer and in diluted beer is studied by tuning the sensitivity of the biosensor using the pH value of the measurement solution. Y1 - 2022 U6 - http://dx.doi.org/10.3390/chemosensors10060218 SN - 2227-9040 N1 - This article belongs to the Special Issue "Nanostructured Devices for Biochemical Sensing" VL - 10 IS - 6 PB - MDPI CY - Basel ER - TY - CHAP A1 - Welden, Melanie A1 - Severins, Robin A1 - Poghossian, Arshak A1 - Wege, Christina A1 - Siegert, Petra A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Studying the immobilization of acetoin reductase with Tobacco mosaic virus particles on capacitive field-effect sensors T2 - 2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN) N2 - A capacitive electrolyte-insulator-semiconductor (EISCAP) biosensor modified with Tobacco mosaic virus (TMV) particles for the detection of acetoin is presented. The enzyme acetoin reductase (AR) was immobilized on the surface of the EISCAP using TMV particles as nanoscaffolds. The study focused on the optimization of the TMV-assisted AR immobilization on the Ta 2 O 5 -gate EISCAP surface. The TMV-assisted acetoin EISCAPs were electrochemically characterized by means of leakage-current, capacitance-voltage, and constant-capacitance measurements. The TMV-modified transducer surface was studied via scanning electron microscopy. KW - Tobacco mosaic virus KW - acetoin KW - capacitive field-effect biosensor KW - enzyme immobilization Y1 - 2022 SN - 978-1-6654-5860-3 (Online) SN - 978-1-6654-5861-0 (Print) U6 - http://dx.doi.org/10.1109/ISOEN54820.2022.9789657 N1 - IEEE International Symposium on Olfaction and Electronic Nose (ISOEN), 29 May 2022 - 01 June 2022, Aveiro, Portugal. PB - IEEE ER - TY - JOUR A1 - Ojovan, Michael I. A1 - Steinmetz, Hans-Jürgen T1 - Approaches to Disposal of Nuclear Waste JF - Energies N2 - We present a concise mini overview on the approaches to the disposal of nuclear waste currently used or deployed. The disposal of nuclear waste is the end point of nuclear waste management (NWM) activities and is the emplacement of waste in an appropriate facility without the intention to retrieve it. The IAEA has developed an internationally accepted classification scheme based on the end points of NWM, which is used as guidance. Retention times needed for safe isolation of waste radionuclides are estimated based on the radiotoxicity of nuclear waste. Disposal facilities usually rely on a multi-barrier defence system to isolate the waste from the biosphere, which comprises the natural geological barrier and the engineered barrier system. Disposal facilities could be of a trench type, vaults, tunnels, shafts, boreholes, or mined repositories. A graded approach relates the depth of the disposal facilities’ location with the level of hazard. Disposal practices demonstrate the reliability of nuclear waste disposal with minimal expected impacts on the environment and humans. KW - borehole disposal KW - geological disposal KW - disposal facility KW - retention time KW - nuclear waste Y1 - 2022 U6 - http://dx.doi.org/10.3390/en15207804 SN - 1996-1073 N1 - This article belongs to the Special Issue "Treatment of Radioactive Waste and Sustainability Energy" VL - 15 IS - 20 PB - MDPI CY - Basel ER - TY - GEN A1 - Wiegner, J. A1 - Volker, H. A1 - Mainz, F. A1 - Backes, A. A1 - Löken, M. A1 - Hüning, Felix T1 - Wiegand-Effect-Powered Wireless IT Sensor Node N2 - With the growing interest in small distributed sensors for the “Internet of Things”, more attention is being paid to energy harvesting techologies. Reducing or eliminating the need for external power sources or batteries make devices more self-sufficient, more reliable, and reduces maintenance requirements. The Wiegand effect is a proven technology for harvesting small amounts of electrical power from mechanical motion. Y1 - 2022 N1 - PSMA International Energy Harvesting Workshop ~ 5-7 April 2022, Raleigh, NC, USA ER - TY - THES A1 - Rouenhoff, Saskia T1 - Blind – invisible connection : ein Spiel zur kritischen Auseinandersetzung mit den sozialen Medien. N2 - Im Computerspiel „blind – invisible connection“ taucht der Spieler in eine Fantasiewelt ein, die die sozialen Medien widerspiegelt und von einer Maschine beherrscht wird. Um zu erfahren, was in dieser Welt geschehen ist, muss die Geschichte Schritt für Schritt erspielt und wie ein Puzzle zusammengesetzt werden. Dabei interagieren die Spieler:innen mittels Dialogen mit den Bewohner:innen der Fantasiewelt und lösen Rätsel, die die Geschichte enthüllen. Durch Analogien zwischen der Fantasiewelt und den sozialen Medien wird die Funktionsweise und der Einfluss der Plattformen auf die Menschen und die Gesellschaft verdeutlicht. So wird eine Reflexion des eigenen Umgangs mit den sozialen Medien angeregt und Gesprächsstoff für Diskussionen unter den Spieler:innen und Mitmenschen geliefert. KW - Spiel KW - Computerspiel KW - App KW - Geschichte KW - Soziale Medien Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Zhantlessova, Sirina A1 - Savitskaya, Irina A1 - Kistaubayeva, Aida A1 - Ignatova, Ludmila A1 - Talipova, Aizhan A1 - Pogrebnjak, Alexander A1 - Digel, Ilya T1 - Advanced “Green” prebiotic composite of bacterial cellulose/pullulan based on synthetic biology-powered microbial coculture strategy JF - Polymers N2 - Bacterial cellulose (BC) is a biopolymer produced by different microorganisms, but in biotechnological practice, Komagataeibacter xylinus is used. The micro- and nanofibrillar structure of BC, which forms many different-sized pores, creates prerequisites for the introduction of other polymers into it, including those synthesized by other microorganisms. The study aims to develop a cocultivation system of BC and prebiotic producers to obtain BC-based composite material with prebiotic activity. In this study, pullulan (PUL) was found to stimulate the growth of the probiotic strain Lactobacillus rhamnosus GG better than the other microbial polysaccharides gellan and xanthan. BC/PUL biocomposite with prebiotic properties was obtained by cocultivation of Komagataeibacter xylinus and Aureobasidium pullulans, BC and PUL producers respectively, on molasses medium. The inclusion of PUL in BC is proved gravimetrically by scanning electron microscopy and by Fourier transformed infrared spectroscopy. Cocultivation demonstrated a composite effect on the aggregation and binding of BC fibers, which led to a significant improvement in mechanical properties. The developed approach for “grafting” of prebiotic activity on BC allows preparation of environmentally friendly composites of better quality. KW - coculture KW - pullulan KW - exopolysaccharides KW - prebiotic KW - bacterial cellulose Y1 - 2022 U6 - http://dx.doi.org/10.3390/polym14153224 SN - 2073-4360 N1 - This article belongs to the Special Issue "Cellulose Based Composites" VL - 14 IS - 15 PB - MDPI CY - Basel ER - TY - JOUR A1 - Welden, Melanie A1 - Poghossian, Arshak A1 - Vahidpour, Farnoosh A1 - Wendlandt, Tim A1 - Keusgen, Michael A1 - Wege, Christina A1 - Schöning, Michael Josef T1 - Towards multi-analyte detection with field-effect capacitors modified with tobacco mosaic virus bioparticles as enzyme nanocarriers JF - Biosensors N2 - Utilizing an appropriate enzyme immobilization strategy is crucial for designing enzyme-based biosensors. Plant virus-like particles represent ideal nanoscaffolds for an extremely dense and precise immobilization of enzymes, due to their regular shape, high surface-to-volume ratio and high density of surface binding sites. In the present work, tobacco mosaic virus (TMV) particles were applied for the co-immobilization of penicillinase and urease onto the gate surface of a field-effect electrolyte-insulator-semiconductor capacitor (EISCAP) with a p-Si-SiO₂-Ta₂O₅ layer structure for the sequential detection of penicillin and urea. The TMV-assisted bi-enzyme EISCAP biosensor exhibited a high urea and penicillin sensitivity of 54 and 85 mV/dec, respectively, in the concentration range of 0.1–3 mM. For comparison, the characteristics of single-enzyme EISCAP biosensors modified with TMV particles immobilized with either penicillinase or urease were also investigated. The surface morphology of the TMV-modified Ta₂O₅-gate was analyzed by scanning electron microscopy. Additionally, the bi-enzyme EISCAP was applied to mimic an XOR (Exclusive OR) enzyme logic gate. KW - urease KW - enzyme-logic gate KW - bi-enzyme biosensor KW - capacitive field-effect sensor KW - tobacco mosaic virus (TMV) KW - penicillinase Y1 - 2022 U6 - http://dx.doi.org/10.3390/bios12010043 SN - 2079-6374 N1 - This article belongs to the Special Issue "Biosensors: 10th Anniversary Feature Papers" VL - 12 IS - 1 PB - MDPI CY - Basel ER - TY - BOOK A1 - Laack, Walter van T1 - Greater Than the Entire Universe Y1 - 2022 SN - 978-3-936624-52-6 PB - van Laack GmbH CY - Aachen ER - TY - BOOK A1 - Laack, Walter van T1 - Aufruf zum Nachdenken: Corona und neue Kriege – Wie kann die Menschheit überleben? T1 - Call for Reflection: Corona and New Wars – How can Mankind survive? Y1 - 2022 SN - 978-3-936624-56-4 N1 - Dritter Band der Buchreihe “Vorträge & Einsichten – Lectures & Insights” und hier das zweite “Upside-Down-Buch”: Deutsche und englische Version in einem Buch. PB - van Laack GmbH CY - Aachen ER - TY - BOOK A1 - Laack, Walter van T1 - Schnittstelle Tod: Was lernen wir durch Corona über Leben und Tod? Y1 - 2022 SN - 978-3-936624-53-3 N1 - Siebter Tagungsband aus der Buchreihe “Schnittstelle Tod” PB - van Laack GmbH CY - Aachen ER - TY - JOUR A1 - Kahmann, Stephanie L. A1 - Rausch, Valentin A1 - Plümer, Jonathan A1 - Müller, Lars P. A1 - Pieper, Martin A1 - Wegmann, Kilian T1 - The automized fracture edge detection and generation of three-dimensional fracture probability heat maps JF - Medical Engineering & Physics N2 - With proven impact of statistical fracture analysis on fracture classifications, it is desirable to minimize the manual work and to maximize repeatability of this approach. We address this with an algorithm that reduces the manual effort to segmentation, fragment identification and reduction. The fracture edge detection and heat map generation are performed automatically. With the same input, the algorithm always delivers the same output. The tool transforms one intact template consecutively onto each fractured specimen by linear least square optimization, detects the fragment edges in the template and then superimposes them to generate a fracture probability heat map. We hypothesized that the algorithm runs faster than the manual evaluation and with low (< 5 mm) deviation. We tested the hypothesis in 10 fractured proximal humeri and found that it performs with good accuracy (2.5 mm ± 2.4 mm averaged Euclidean distance) and speed (23 times faster). When applied to a distal humerus, a tibia plateau, and a scaphoid fracture, the run times were low (1–2 min), and the detected edges correct by visual judgement. In the geometrically complex acetabulum, at a run time of 78 min some outliers were considered acceptable. An automatically generated fracture probability heat map based on 50 proximal humerus fractures matches the areas of high risk of fracture reported in medical literature. Such automation of the fracture analysis method is advantageous and could be extended to reduce the manual effort even further. KW - Fracture classification KW - Shoulder KW - Probability distribution mapping KW - Morphing KW - Imaging Y1 - 2022 SN - 1350-4533 VL - 2022 IS - 110 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Schwager, Christian A1 - Flesch, Robert A1 - Schwarzbözl, Peter A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José T1 - Advanced two phase flow model for transient molten salt receiver system simulation JF - Solar Energy N2 - In order to realistically predict and optimize the actual performance of a concentrating solar power (CSP) plant sophisticated simulation models and methods are required. This paper presents a detailed dynamic simulation model for a Molten Salt Solar Tower (MST) system, which is capable of simulating transient operation including detailed startup and shutdown procedures including drainage and refill. For appropriate representation of the transient behavior of the receiver as well as replication of local bulk and surface temperatures a discretized receiver model based on a novel homogeneous two-phase (2P) flow modelling approach is implemented in Modelica Dymola®. This allows for reasonable representation of the very different hydraulic and thermal properties of molten salt versus air as well as the transition between both. This dynamic 2P receiver model is embedded in a comprehensive one-dimensional model of a commercial scale MST system and coupled with a transient receiver flux density distribution from raytracing based heliostat field simulation. This enables for detailed process prediction with reasonable computational effort, while providing data such as local salt film and wall temperatures, realistic control behavior as well as net performance of the overall system. Besides a model description, this paper presents some results of a validation as well as the simulation of a complete startup procedure. Finally, a study on numerical simulation performance and grid dependencies is presented and discussed. KW - Molten salt solar tower KW - Molten salt receiver system KW - Dynamic simulation KW - Two-phase modelling KW - Transient flux distribution Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.solener.2021.12.065 SN - 0038-092X (print) SN - 1471-1257 (online) VL - 232 SP - 362 EP - 375 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Gedle, Yibekal A1 - Schmitz, Mark A1 - Gielen, Hans A1 - Schmitz, Pascal A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José A1 - Mahdi, Zahra A1 - Caminos, Ricardo Alexander Chico A1 - Dersch, Jürgen T1 - Analysis of an integrated CSP-PV hybrid power plant T2 - SolarPACES 2020 N2 - In the past, CSP and PV have been seen as competing technologies. Despite massive reductions in the electricity generation costs of CSP plants, PV power generation is - at least during sunshine hours - significantly cheaper. If electricity is required not only during the daytime, but around the clock, CSP with its inherent thermal energy storage gets an advantage in terms of LEC. There are a few examples of projects in which CSP plants and PV plants have been co-located, meaning that they feed into the same grid connection point and ideally optimize their operation strategy to yield an overall benefit. In the past eight years, TSK Flagsol has developed a plant concept, which merges both solar technologies into one highly Integrated CSP-PV-Hybrid (ICPH) power plant. Here, unlike in simply co-located concepts, as analyzed e.g. in [1] – [4], excess PV power that would have to be dumped is used in electric molten salt heaters to increase the storage temperature, improving storage and conversion efficiency. The authors demonstrate the electricity cost sensitivity to subsystem sizing for various market scenarios, and compare the resulting optimized ICPH plants with co-located hybrid plants. Independent of the three feed-in tariffs that have been assumed, the ICPH plant shows an electricity cost advantage of almost 20% while maintaining a high degree of flexibility in power dispatch as it is characteristic for CSP power plants. As all components of such an innovative concept are well proven, the system is ready for commercial market implementation. A first project is already contracted and in early engineering execution. KW - Hybrid energy system KW - Power plants KW - Electricity generation KW - Energy storage KW - Associated liquids Y1 - 2022 SN - 978-0-7354-4195-8 U6 - http://dx.doi.org/10.1063/5.0086236 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - 26th International Conference on Concentrating Solar Power and Chemical Energy Systems 28 September–2 October 2020 Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Mahdi, Zahra A1 - Dersch, Jürgen A1 - Schmitz, Pascal A1 - Dieckmann, Simon A1 - Caminos, Ricardo Alexander Chico A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf A1 - Schwager, Christian A1 - Schmitz, Mark A1 - Gielen, Hans A1 - Gedle, Yibekal A1 - Büscher, Rauno T1 - Technical assessment of Brayton cycle heat pumps for the integration in hybrid PV-CSP power plants T2 - SOLARPACES 2020 N2 - The hybridization of Concentrated Solar Power (CSP) and Photovoltaics (PV) systems is a promising approach to reduce costs of solar power plants, while increasing dispatchability and flexibility of power generation. High temperature heat pumps (HT HP) can be utilized to boost the salt temperature in the thermal energy storage (TES) of a Parabolic Trough Collector (PTC) system from 385 °C up to 565 °C. A PV field can supply the power for the HT HP, thus effectively storing the PV power as thermal energy. Besides cost-efficiently storing energy from the PV field, the power block efficiency of the overall system is improved due to the higher steam parameters. This paper presents a technical assessment of Brayton cycle heat pumps to be integrated in hybrid PV-CSP power plants. As a first step, a theoretical analysis was carried out to find the most suitable working fluid. The analysis included the fluids Air, Argon (Ar), Nitrogen (N2) and Carbon dioxide (CO2). N2 has been chosen as the optimal working fluid for the system. After the selection of the ideal working medium, different concepts for the arrangement of a HT HP in a PV-CSP hybrid power plant were developed and simulated in EBSILON®Professional. The concepts were evaluated technically by comparing the number of components required, pressure losses and coefficient of performance (COP). KW - Solar thermal technologies KW - Hybrid energy system KW - Concentrated solar power KW - Power plants KW - Energy storage Y1 - 2022 SN - 978-0-7354-4195-8 U6 - http://dx.doi.org/10.1063/5.0086269 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - 26th International Conference on Concentrating Solar Power and Chemical Energy Systems 28 September–2 October 2020 Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Zahra, Mahdi A1 - Phani Srujan, Merige A1 - Caminos, Ricardo Alexander Chico A1 - Schmitz, Pascal A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José A1 - Schmitz, Mark A1 - Gielen, Hans A1 - Gedle, Yibekal A1 - Dersch, Jürgen T1 - Modeling the thermal behavior of solar salt in electrical resistance heaters for the application in PV-CSP hybrid power plants T2 - SOLARPACES 2020 N2 - Concentrated Solar Power (CSP) systems are able to store energy cost-effectively in their integrated thermal energy storage (TES). By intelligently combining Photovoltaics (PV) systems with CSP, a further cost reduction of solar power plants is expected, as well as an increase in dispatchability and flexibility of power generation. PV-powered Resistance Heaters (RH) can be deployed to raise the temperature of the molten salt hot storage from 385 °C up to 565 °C in a Parabolic Trough Collector (PTC) plant. To avoid freezing and decomposition of molten salt, the temperature distribution in the electrical resistance heater is investigated in the present study. For this purpose, a RH has been modeled and CFD simulations have been performed. The simulation results show that the hottest regions occur on the electric rod surface behind the last baffle. A technical optimization was performed by adjusting three parameters: Shell-baffle clearance, electric rod-baffle clearance and number of baffles. After the technical optimization was carried out, the temperature difference between the maximum temperature and the average outlet temperature of the salt is within the acceptable limits, thus critical salt decomposition has been avoided. Additionally, the CFD simulations results were analyzed and compared with results obtained with a one-dimensional model in Modelica. KW - Solar thermal technologies KW - Hybrid energy system KW - Concentrated solar power KW - Energy storage KW - Photovoltaics Y1 - 2022 SN - 978-0-7354-4195-8 U6 - http://dx.doi.org/10.1063/5.0086268 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - 26th International Conference on Concentrating Solar Power and Chemical Energy Systems 28 September–2 October 2020 Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Caminos, Ricardo Alexander Chico A1 - Schmitz, Pascal A1 - Atti, Vikrama A1 - Mahdi, Zahra A1 - Teixeira Boura, Cristiano José A1 - Sattler, Johannes Christoph A1 - Herrmann, Ulf A1 - Hilger, Patrick A1 - Dieckmann, Simon T1 - Development of a micro heliostat and optical qualification assessment with a 3D laser scanning method T2 - SOLARPACES 2020 N2 - The Solar-Institut Jülich (SIJ) and the companies Hilger GmbH and Heliokon GmbH from Germany have developed a small-scale cost-effective heliostat, called “micro heliostat”. Micro heliostats can be deployed in small-scale concentrated solar power (CSP) plants to concentrate the sun's radiation for electricity generation, space or domestic water heating or industrial process heat. In contrast to conventional heliostats, the special feature of a micro heliostat is that it consists of dozens of parallel-moving, interconnected, rotatable mirror facets. The mirror facets array is fixed inside a box-shaped module and is protected from weathering and wind forces by a transparent glass cover. The choice of the building materials for the box, tracking mechanism and mirrors is largely dependent on the selected production process and the intended application of the micro heliostat. Special attention was paid to the material of the tracking mechanism as this has a direct influence on the accuracy of the micro heliostat. The choice of materials for the mirror support structure and the tracking mechanism is made in favor of plastic molded parts. A qualification assessment method has been developed by the SIJ in which a 3D laser scanner is used in combination with a coordinate measuring machine (CMM). For the validation of this assessment method, a single mirror facet was scanned and the slope deviation was computed. KW - Concentrated solar power KW - Electricity generation KW - Measuring instruments KW - Heliostats KW - Global change Y1 - 2022 SN - 978-0-7354-4195-8 U6 - http://dx.doi.org/10.1063/5.0086262 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - 26th International Conference on Concentrating Solar Power and Chemical Energy Systems 28 September–2 October 2020 Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Niederwestberg, Stefan A1 - Schneider, Falko A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Introduction to a direct irradiated transparent tube particle receiver T2 - SOLARPACES 2020 N2 - New materials often lead to innovations and advantages in technical applications. This also applies to the particle receiver proposed in this work that deploys high-temperature and scratch resistant transparent ceramics. With this receiver design, particles are heated through direct-contact concentrated solar irradiance while flowing downwards through tubular transparent ceramics from top to bottom. In this paper, the developed particle receiver as well as advantages and disadvantages are described. Investigations on the particle heat-up characteristics from solar irradiance were carried out with DEM simulations which indicate that particle temperatures can reach up to 1200 K. Additionally, a simulation model was set up for investigating the dynamic behavior. A test receiver at laboratory scale has been designed and is currently being built. In upcoming tests, the receiver test rig will be used to validate the simulation results. The design and the measurement equipment is described in this work. KW - Solar irradiance KW - Ceramics Y1 - 2022 SN - 978-0-7354-4195-8 U6 - http://dx.doi.org/10.1063/5.0086735 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - 26th International Conference on Concentrating Solar Power and Chemical Energy Systems 28 September–2 October 2020 Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - CHAP A1 - Sattler, Johannes Christoph A1 - Schneider, Iesse Peer A1 - Angele, Florian A1 - Atti, Vikrama A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Development of heliostat field calibration methods: Theory and experimental test results T2 - SolarPACES conference proceedings N2 - In this work, three patent pending calibration methods for heliostat fields of central receiver systems (CRS) developed by the Solar-Institut Jülich (SIJ) of the FH Aachen University of Applied Sciences are presented. The calibration methods can either operate in a combined mode or in stand-alone mode. The first calibration method, method A, foresees that a camera matrix is placed into the receiver plane where it is subjected to concentrated solar irradiance during a measurement process. The second calibration method, method B, uses an unmanned aerial vehicle (UAV) such as a quadrocopter to automatically fly into the reflected solar irradiance cross-section of one or more heliostats (two variants of method B were tested). The third calibration method, method C, foresees a stereo central camera or multiple stereo cameras installed e.g. on the solar tower whereby the orientations of the heliostats are calculated from the location detection of spherical red markers attached to the heliostats. The most accurate method is method A which has a mean accuracy of 0.17 mrad. The mean accuracy of method B variant 1 is 1.36 mrad and of variant 2 is 1.73 mrad. Method C has a mean accuracy of 15.07 mrad. For method B there is great potential regarding improving the measurement accuracy. For method C the collected data was not sufficient for determining whether or not there is potential for improving the accuracy. KW - Heliostat Field Calibration KW - Unmanned aerial vehicle KW - UAV KW - Quadrocopter KW - Camera system Y1 - 2024 U6 - http://dx.doi.org/10.52825/solarpaces.v1i.678 SN - 2751-9899 (online) N1 - 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - Vol. 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Sattler, Johannes Christoph A1 - Atti, Vikrama A1 - Alexopoulos, Spiros A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf A1 - Dutta, Siddharth A1 - Kioutsioukis, Ioannis T1 - DNI forecast tool for the smart operation of a parabolic trough collector system with concrete thermal energy storage: Theory, results and outlook T2 - SolarPACES conference proceedings N2 - This work presents a basic forecast tool for predicting direct normal irradiance (DNI) in hourly resolution, which the Solar-Institut Jülich (SIJ) is developing within a research project. The DNI forecast data shall be used for a parabolic trough collector (PTC) system with a concrete thermal energy storage (C-TES) located at the company KEAN Soft Drinks Ltd in Limassol, Cyprus. On a daily basis, 24-hour DNI prediction data in hourly resolution shall be automatically produced using free or very low-cost weather forecast data as input. The purpose of the DNI forecast tool is to automatically transfer the DNI forecast data on a daily basis to a main control unit (MCU). The MCU automatically makes a smart decision on the operation mode of the PTC system such as steam production mode and/or C-TES charging mode. The DNI forecast tool was evaluated using historical data of measured DNI from an on-site weather station, which was compared to the DNI forecast data. The DNI forecast tool was tested using data from 56 days between January and March 2022, which included days with a strong variation in DNI due to cloud passages. For the evaluation of the DNI forecast reliability, three categories were created and the forecast data was sorted accordingly. The result was that the DNI forecast tool has a reliability of 71.4 % based on the tested days. The result fulfils SIJ’s aim to achieve a reliability of around 70 %, but SIJ aims to still improve the DNI forecast quality. KW - Direct normal irradiance forecast KW - DNI forecast KW - Parabolic trough collector KW - PTC KW - Thermal Energy Storage Y1 - 2024 U6 - http://dx.doi.org/10.52825/solarpaces.v1i.731 SN - 2751-9899 (online) N1 - 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - VOL. 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Schwager, Christian A1 - Angele, Florian A1 - Nouri, Bijan A1 - Schwarzbözl, Peter A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Impact of DNI forecast quality on performance prediction for a commercial scale solar tower: Application of nowcasting DNI maps to dynamic solar tower simulation T2 - SolarPACES conference proceedings N2 - Concerning current efforts to improve operational efficiency and to lower overall costs of concentrating solar power (CSP) plants with prediction-based algorithms, this study investigates the quality and uncertainty of nowcasting data regarding the implications for process predictions. DNI (direct normal irradiation) maps from an all-sky imager-based nowcasting system are applied to a dynamic prediction model coupled with ray tracing. The results underline the need for high-resolution DNI maps in order to predict net yield and receiver outlet temperature realistically. Furthermore, based on a statistical uncertainty analysis, a correlation is developed, which allows for predicting the uncertainty of the net power prediction based on the corresponding DNI forecast uncertainty. However, the study reveals significant prediction errors and the demand for further improvement in the accuracy at which local shadings are forecasted. KW - Process prediction KW - DNI forecasting KW - Nowcasting KW - Uncertainty analysis KW - Molten salt receiver system, Y1 - 2024 U6 - http://dx.doi.org/10.52825/solarpaces.v1i.675 SN - 2751-9899 (online) N1 - 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - Vol. 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Schulte, Jonas A1 - Schwager, Christian A1 - Frantz, Cathy A1 - Schloms, Felix A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Control concept for a molten salt receiver in star design: Development, optimization and testing with cloud passage scenarios T2 - SolarPACES conference proceedings N2 - A promising approach to reduce the system costs of molten salt solar receivers is to enable the irradiation of the absorber tubes on both sides. The star design is an innovative receiver design, pursuing this approach. The unconventional design leads to new challenges in controlling the system. This paper presents a control concept for a molten salt receiver system in star design. The control parameters are optimized in a defined test cycle by minimizing a cost function. The control concept is tested in realistic cloud passage scenarios based on real weather data. During these tests, the control system showed no sign of unstable behavior, but to perform sufficiently in every scenario further research and development like integrating Model Predictive Controls (MPCs) need to be done. The presented concept is a starting point to do so. KW - Molten salt receiver KW - Star design KW - Control optimization KW - Cloud passages Y1 - 2023 U6 - http://dx.doi.org/10.52825/solarpaces.v1i.693 SN - 2751-9899 (online) N1 - 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - Vol. 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Bergmann, Ole A1 - Götten, Falk A1 - Braun, Carsten A1 - Janser, Frank T1 - Comparison and evaluation of blade element methods against RANS simulations and test data T2 - CEAS Aeronautical Journal N2 - This paper compares several blade element theory (BET) method-based propeller simulation tools, including an evaluation against static propeller ground tests and high-fidelity Reynolds-Average Navier Stokes (RANS) simulations. Two proprietary propeller geometries for paraglider applications are analysed in static and flight conditions. The RANS simulations are validated with the static test data and used as a reference for comparing the BET in flight conditions. The comparison includes the analysis of varying 2D aerodynamic airfoil parameters and different induced velocity calculation methods. The evaluation of the BET propeller simulation tools shows the strength of the BET tools compared to RANS simulations. The RANS simulations underpredict static experimental data within 10% relative error, while appropriate BET tools overpredict the RANS results by 15–20% relative error. A variation in 2D aerodynamic data depicts the need for highly accurate 2D data for accurate BET results. The nonlinear BET coupled with XFOIL for the 2D aerodynamic data matches best with RANS in static operation and flight conditions. The novel BET tool PropCODE combines both approaches and offers further correction models for highly accurate static and flight condition results. KW - BET KW - CFD propeller simulation KW - Propeller aerodynamics KW - Actuator disk modelling KW - Propeller performance Y1 - 2022 U6 - http://dx.doi.org/10.1007/s13272-022-00579-1 SN - 1869-5590 (Online) SN - 1869-5582 (Print) N1 - Corresponding author: Ole Bergmann VL - 13 SP - 535 EP - 557 PB - Springer CY - Wien ER - TY - THES A1 - Nordmann, Alexander T1 - Prozessüberwachung beim Werkzeugschleifen von WC-Co Hartmetallschaftfräsern Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vu, Tuan Dat T1 - Objekterkennung und Schienenerkennung in der Schienenfahrzeugtechnik Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - BOOK A1 - Engelmann, Ulrich M. T1 - Zielführend moderieren N2 - In der Teamarbeit wird Moderation zum Erfolgsfaktor, der jedoch häufig unterschätzt wird. Ausgehend vom persönlichen Kompetenzniveau verknüpft dieses Buch Grundlagen und Methoden zu Wegen, um Ihre persönliche Entwicklung individuell zu begleiten: Neulinge finden hilfreiche Checklisten und Basistechniken für ihre ersten Moderationen, Fortgeschrittene wertvolle Praxistipps und Methoden für den Ausbau ihrer Moderationskompetenz. Profis schließlich genießen eine raffinierte Aussicht auf weniger bekannte Techniken und neue Anwendungen. Weiterführende Exkurse zum Meeting-Management und zur Online-Moderation runden den Anwendungshorizont ab. Ob in Beruf, Studium oder Ehrenamt – derart ausgestattet gelingen Ihre eigene sowie die Entwicklung Ihres Teams durch zielführende Moderationen. Y1 - 2022 SN - 9783838556895 U6 - http://dx.doi.org/10.36198/9783838556895 PB - UVK Verlag CY - Stuttgart ER - TY - CHAP A1 - Golland, Alexander ED - Taeger, Jürgen ED - Gabel, Detlev T1 - Kommentierung von Artikel 94 bis 99 Datenschutz-Grundverordnung T2 - DSGVO - BDSG - TTDSG: Datenschutzgrundverordnung - Bundesdatenschutzgesetz - Telekommunikation-Telemedien-Datenschutzgesetz N2 - Das Werk kommentiert leicht verständlich, aktuell und praxisnah die DSGVO sowie das BDSG und - neu - auch das TTDSG (Telekommunikation-Telemedien-Datenschutzgesetz). Verantwortliche erhalten damit eine umfassende Darstellung mit Handlungsempfehlungen zum gesamten neuen Datenschutzrecht. Betriebliche Datenschutzbeauftragte können sich an den fundierten Kommentierungen orientieren, in denen Literatur und Rechtsprechung aktuell berücksichtigt wurden. KW - Telekommunikation-Telemedien-Datenschutzgesetz KW - Internationales Recht / Europarecht KW - Datenschutzfolgenabschätzung KW - EU-Datenschutzgrundverordnung KW - Betroffenenrechte Y1 - 2022 SN - 978-3-8005-1760-2 SP - 1575 EP - 1621 PB - Fachmedien Recht und Wirtschaft CY - Frankfurt am Main ET - 4., neu bearbeitete Auflage. 2022 ER - TY - JOUR A1 - Topçu, Murat A1 - Madabhushi, Gopal S.P. A1 - Staat, Manfred T1 - A generalized shear-lag theory for elastic stress transfer between matrix and fibres having a variable radius JF - International Journal of Solids and Structures N2 - A generalized shear-lag theory for fibres with variable radius is developed to analyse elastic fibre/matrix stress transfer. The theory accounts for the reinforcement of biological composites, such as soft tissue and bone tissue, as well as for the reinforcement of technical composite materials, such as fibre-reinforced polymers (FRP). The original shear-lag theory proposed by Cox in 1952 is generalized for fibres with variable radius and with symmetric and asymmetric ends. Analytical solutions are derived for the distribution of axial and interfacial shear stress in cylindrical and elliptical fibres, as well as conical and paraboloidal fibres with asymmetric ends. Additionally, the distribution of axial and interfacial shear stress for conical and paraboloidal fibres with symmetric ends are numerically predicted. The results are compared with solutions from axisymmetric finite element models. A parameter study is performed, to investigate the suitability of alternative fibre geometries for use in FRP. KW - Natural fibres KW - Polymer-matrix composites KW - Biocomposites KW - Stress concentrations KW - Finite element analysis Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.ijsolstr.2022.111464 SN - 0020-7683 VL - 239–240 IS - Art. No. 111464 PB - Elsevier CY - New York, NY ER - TY - JOUR A1 - Golland, Alexander T1 - Aufsicht und Rechtsdurchsetzung bei unzulässigem Einsatz von Cookies & Co. unter Geltung des TTDSG JF - DSB Datenschutz-Berater KW - Informationstechnik KW - Rechtsgebiet KW - Datenschutz KW - Bundesrepublik Deutschland Y1 - 2022 SN - 0170-7256 VL - 46 IS - 1 SP - 14 EP - 16 PB - Deutscher Fachverlag GmbH CY - Frankfurt a.M. ER - TY - JOUR A1 - Mandekar, Swati A1 - Holland, Abigail A1 - Thielen, Moritz A1 - Behbahani, Mehdi A1 - Melnykowycz, Mark T1 - Advancing towards Ubiquitous EEG, Correlation of In-Ear EEG with Forehead EEG JF - Sensors N2 - Wearable EEG has gained popularity in recent years driven by promising uses outside of clinics and research. The ubiquitous application of continuous EEG requires unobtrusive form-factors that are easily acceptable by the end-users. In this progression, wearable EEG systems have been moving from full scalp to forehead and recently to the ear. The aim of this study is to demonstrate that emerging ear-EEG provides similar impedance and signal properties as established forehead EEG. EEG data using eyes-open and closed alpha paradigm were acquired from ten healthy subjects using generic earpieces fitted with three custom-made electrodes and a forehead electrode (at Fpx) after impedance analysis. Inter-subject variability in in-ear electrode impedance ranged from 20 kΩ to 25 kΩ at 10 Hz. Signal quality was comparable with an SNR of 6 for in-ear and 8 for forehead electrodes. Alpha attenuation was significant during the eyes-open condition in all in-ear electrodes, and it followed the structure of power spectral density plots of forehead electrodes, with the Pearson correlation coefficient of 0.92 between in-ear locations ELE (Left Ear Superior) and ERE (Right Ear Superior) and forehead locations, Fp1 and Fp2, respectively. The results indicate that in-ear EEG is an unobtrusive alternative in terms of impedance, signal properties and information content to established forehead EEG. KW - in-ear EEG KW - correlation KW - forehead EEG KW - impedance spectroscopy KW - biopotential electrodes Y1 - 2022 U6 - http://dx.doi.org/10.3390/s22041568 SN - 1424-8220 VL - 22 IS - 4 SP - 1 EP - 19 PB - MDPI CY - Basel ER - TY - JOUR A1 - Defosse, Jerome A1 - Kleinschmidt, Joris A1 - Schmutz, Axel A1 - Loop, Torsten A1 - Staat, Manfred A1 - Gatzweiler, Karl-Heinz A1 - Wappler, Frank A1 - Schieren, Mark T1 - Dental strain on maxillary incisors during tracheal intubation with double-lumen tubes and different laryngoscopy techniques - a blinded manikin study JF - Journal of Cardiothoracic and Vascular Anesthesia KW - anaesthetic complications KW - dental trauma KW - difficult airway KW - double-lumen tube intubation KW - videolaryngoscopy Y1 - 2022 U6 - http://dx.doi.org/10.1053/j.jvca.2022.02.017 SN - 1053-0770 VL - 36 IS - 8, Part B SP - 3021 EP - 3027 PB - Elsevier CY - New York, NY ER - TY - JOUR A1 - Rübbelke, Dirk A1 - Vögele, Stefan A1 - Grajewski, Matthias A1 - Zobel, Luzy T1 - Hydrogen-based steel production and global climate protection: An empirical analysis of the potential role of a European cross border adjustment mechanism JF - Journal of Cleaner Production N2 - The European Union's aim to become climate neutral by 2050 necessitates ambitious efforts to reduce carbon emissions. Large reductions can be attained particularly in energy intensive sectors like iron and steel. In order to prevent the relocation of such industries outside the EU in the course of tightening environmental regulations, the establishment of a climate club jointly with other large emitters and alternatively the unilateral implementation of an international cross-border carbon tax mechanism are proposed. This article focuses on the latter option choosing the steel sector as an example. In particular, we investigate the financial conditions under which a European cross border mechanism is capable to protect hydrogen-based steel production routes employed in Europe against more polluting competition from abroad. By using a floor price model, we assess the competitiveness of different steel production routes in selected countries. We evaluate the climate friendliness of steel production on the basis of specific GHG emissions. In addition, we utilize an input-output price model. It enables us to assess impacts of rising cost of steel production on commodities using steel as intermediates. Our results raise concerns that a cross-border tax mechanism will not suffice to bring about competitiveness of hydrogen-based steel production in Europe because the cost tends to remain higher than the cost of steel production in e.g. China. Steel is a classic example for a good used mainly as intermediate for other products. Therefore, a cross-border tax mechanism for steel will increase the price of products produced in the EU that require steel as an input. This can in turn adversely affect competitiveness of these sectors. Hence, the effects of higher steel costs on European exports should be borne in mind and could require the cross-border adjustment mechanism to also subsidize exports. Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.jclepro.2022.135040 SN - 0959-6526 VL - 380 IS - Part 2, Art. Nr.:135040 PB - Elsevier ER - TY - GEN A1 - Steuer-Dankert, Linda A1 - Bernhard, Sebastian A1 - Langolf, Jessica A1 - Leicht-Scholten, Carmen T1 - Managing change and acceptance of digitalization strategies - Implementing the vision of „Internet of Production“ (IoP) in existing corporate structures T2 - Textile Impulse für die Zukunft: Aachen-Dresden-Denkendorf International Textile Conference 2022 : 1. – 2. Dezember 2022, Eurogress Aachen N2 - The vision of the Internet of Production is to enable a new level of crossdomain collaboration by providing semantically adequate and context-aware data from production, development & usage in real-time. Y1 - 2022 SP - 153 EP - 153 ER - TY - BOOK A1 - Bundrock, Ronja A1 - Kremers, Nico A1 - Pankok, Lennard A1 - Weisheit, Theresa Maria A1 - Spoede, Jasper ED - Kroll-Ludwigs, Kathrin ED - Bernecker, Andreas ED - Bassen-Metz, Yasmine ED - Eggert, Mathias ED - Fritz, Thomas ED - Golland, Alexander ED - Höhne, Tim ED - Tran, Duc Hung ED - Vogt, Jürgen T1 - Aachener Online-Schriften Wirtschaft und Recht. Band 5. 02/2022 N2 - Inhaltsverzeichnis - Bachelorarbeiten 1. Testamentsgestaltung bei Patchworkfamilien – Lösungsansätze für typische Praxisprobleme unter Berücksichtigung der Interessenlagen der Parteien - Ronja Bundrock 4 - 58 2. Die Haftung des AG-Vorstands gegenüber der Gesellschaft in unterneh- mensinternen und -externen Krisen - Nico Kremers 59 - 122 3. The Relationship of the Ex-Ante Uncertainty about the Value of a Stock and its IPO Underpricing – An Analysis of the German Market - Lennard Pankok 123 - 179 4. Attractiveness Bias in Venture Capital – An Analysis of Investor Decision Making in “Die Höhle der Löwen” - Theresa Maria Weisheit 180 - 242 Inhaltsverzeichnis – Masterarbeiten Erhöhung der Energieautarkie in der Backbranche – Anwendung von bidi- rektionalem Laden und dessen Auswirkungen auf die Geschäftsprozesse und Informationssysteme - Jasper Spoede 243 - 355 T3 - Aachener Online-Schriften Wirtschaft und Recht - 5 Y1 - 2022 PB - FH Aachen / Fachbereich Wirtschaftswissenschaften CY - Aachen ER - TY - THES A1 - Keller, Simon Mark T1 - Risikoanalyse einer bordautonomen Schienenfahrzeugortung mittels GNSS N2 - Bei Schienenfahrzeugen, die mit dem Zugsicherungssystem ETCS betrieben sind, wird die Odometrie durch eine diskrete Ortung mittels physischen Balisen zurückgesetzt. Diese Arbeit befasst sich mit der Innovation von virtuellen Balisen. Virtuelle Balisen, können eingesetzt werden, um physische, im Gleisbett montierte Balisen zu ersetzen. Durch den Einsatz von virtuellen Balisen soll der Infrastrukturausbau von ETCS vorangetrieben werden, indem sie als virtuelle Komponente auf Schienenfahrzeugen eingesetzt werden. Im Rahmen dieser Arbeit wird die Fragestellung beantwortet, ob eine bordautonome Zugortung mittels virtuellen Balisen in einem ausgewählten Szenario mit einem akzeptablen Risiko verbunden ist? Das Szenario besteht aus einem Schienenfahrzeug, welches mit dem Zugsicherungssystem ETCS Level 2 auf einer eingleisigen Nebenstrecke betreiben wird. Hierzu werden zunächst die Grundlagen von ETCS und der satellitenbasierten Ortung erläutert. Des Weiteren werden die Grundlagen des CSM Prozesses und der expliziten Risikoabschätzung eingeführt. Aufbauend auf diesen Grundlagen wird der CSM Prozess angewandt und dabei eine Systemdefinition mit den Schnittstellen des Systems zur Umwelt erstellt. Mit der Hazop-Methode werden die Gefährdungen der Schnittstellen erfasst und beurteilt. Die sicherheitsrelevanten Gefährdungen werden in einer FMEA bewertet. In der folgenden Diskussion werden sicherheitsrelevante Gefährdungen nochmals betrachtet. Das Ergebnis der Arbeit ist, dass im ausgewählten Szenario, unter der Verwendung der CSM-Prozesse und der industriell anerkannten Methoden Hazop und FMEA, die Integration der Board-autonomen-Ortung mit einem akzeptablen Risiko verbunden ist. Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Wabner, Magnus T1 - Aroux N2 - Aeroux ist eine Formstudie über die Gestalt einer Luftschiffgondel. Luftschiffe bzw. Zeppeline werden oft mit dem Unglück der Hindenburg in Lakehurst in Verbindung gebracht. Aeroux versucht diese Assoziation zu überwinden und Luftschiffe in der Gegenwart zu verankern. Durch die gezielte, psychologisch inspirierte Gestaltung soll Sicherheit und Ruhe vermittelt werden, sollen spezifische Assoziationen geweckt werden, die weg führen von Bildern vergangener Tage eines brennenden Luftschiffs, um so Zeppeline als klimafreundlichere Alternative zum Flugzeug wieder ins Spiel zu bringen. Aeroux ist ein hybrides Verkehrsmittel, dass in der Lage ist, sowohl Güter als auch Personen in verschiedenen Szenarien zu transportieren. Zeppeline bauchen keine befestigten Landebahnen oder Pisten. Regionen, die über Straßen schwer zugänglich sind, können so in den Warenhandel integriert werden. Gleichermaßen können aber auch Meschen in Regionen befördert werden, die durch Straßen oder Landebahnen nicht oder unzureichend erschlossen sind. Darüber hinaus kann Aeroux ein Ansatz sein die Unverträglichkeit von Fliegen und Klimaschutz aufzulösen. Nicht zuletzt liegt in der gemächlichen Art der Bewegung ein besonderer Zauber. Reisen könnten einen neuen Charakter erhalten: durch die großen Fensterfronten und die geringe Flughöhe können Landschaften auf der Reise neu wahrgenommen werden, der Weg wird wieder Teil des Reisens. Die Arbeit ist in erster Linie eine Auseinandersetzung mit der Form. Wie wirkt Form, wie lassen sich Assoziationen wecken, lenken, leiten. Wie kann technischer Anspruch, gesellschaftliche Bedingung, ökologisches Bewusstsein und nicht zuletzt Genuss in einem Objekt resultieren. Digitale und analoge Fertigung spielen im Zuge der Arbeit ineinander. So entstand das Design der Gondel, nach ersten händischen Skizzen, digital. Das Model der Gondel wurde aus diesen Daten 3D gedruckt und die Darstellung der Traghülle ebenfalls auf Grundlage dieser Daten gelasert. Aeroux möchte Lust auf alternatives Sehen, Denken und Handeln machen. Es gilt viel zu bewegen. KW - Luftschiff KW - Lasern KW - 3D-Druck KW - Renderings KW - Formensprache Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ebner, Nina T1 - Inside Out : a personal visualisation of aphantasia N2 - Das Projekt behandelt die Thematik von Aphantasie, welche die „Abwesenheit freiwilliger, visuell erzeugter Bilder“ (Fußnote) im Kopf beschreibt. Das Ziel der Arbeit ist die Aufklärung und Sensibilisierung Außenstehender. Durch eine reine faktenbasierte Betrachtungsweise ist dies kaum möglich, weshalb ein visueller Ansatz besser geeignet ist. Das Projekt lokalisiert sich in den Bereichen Fotografie & Ausstellung. Die Fotografien stehen für eine beispielhafte Visualisierung der subjektiven Wahrnehmung der Gestalterin – das Ausstellungsobjekt, eine begehbare Camera obscura, repräsentiert das Innere ihres Kopfes. Die Aufnahmen wurden bei Nacht mit verschiedenen Lichtern innerhalb der Camera obscura abgebildet und abgelichtet. Betrachter:innen der Ausarbeitung sollen einen weiteren Blickwinkel auf die Thematik, die Sichtweise und ihre Auswirkungen erhalten – auch im Kontext und der Arbeit als Designer:in. Fußnote: https://www.psychologie.uni-bonn.de/de/unser-institut/abteilungen/differentielle-biologische-psychologie/%20%20Aphantasia%20Research%20Project%20Bonn%20 KW - Aphantasie KW - Visualisierung KW - Abwesenheit KW - Camera Obscura KW - Wahrnehmung Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Horvath, Nicolas T1 - Neues Corporate Design für das Rautenstrauch Joest Museum Köln N2 - Der Mensch in seinen Welten – das Konzept des Rautenstrauch Joest Museums verfolgt den Ansatz des Kulturvergleichs und strebt im Zuge dessen die Betonung der Ebenbürtigkeit aller Kulturen an. Die Sammlung unterteilt sich nicht – wie gewohnt – anhand geografischer Gesichtspunkte, sondern behandelt Themen, die Menschen auf der ganzen Welt beschäftigen. Das in dieser Arbeit gestaltete neue Erscheinungsbild greift den veränderten gesellschaftlichen Stellenwert von ethnologischen Museen auf und positioniert das Museum als aktiven Diskussionsteilnehmer im Zuge des Postkolonialismus. Das entwickelte Key-Visual aus eigener Schrift, einheitlicher Rastersystematik und prägnantem Farbkonzept gibt einen Einblick darin, wie Menschen früher probiert haben, ihre Welt zu verstehen und sie zu erschließen. KW - Markengestaltung KW - Museum KW - Redesign KW - Postkolonialismus KW - Kunst Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Blaneck, Patrick Gustav A1 - Bornheim, Tobias A1 - Grieger, Niklas A1 - Bialonski, Stephan T1 - Automatic readability assessment of german sentences with transformer ensembles T2 - Proceedings of the GermEval 2022 Workshop on Text Complexity Assessment of German Text N2 - Reliable methods for automatic readability assessment have the potential to impact a variety of fields, ranging from machine translation to self-informed learning. Recently, large language models for the German language (such as GBERT and GPT-2-Wechsel) have become available, allowing to develop Deep Learning based approaches that promise to further improve automatic readability assessment. In this contribution, we studied the ability of ensembles of fine-tuned GBERT and GPT-2-Wechsel models to reliably predict the readability of German sentences. We combined these models with linguistic features and investigated the dependence of prediction performance on ensemble size and composition. Mixed ensembles of GBERT and GPT-2-Wechsel performed better than ensembles of the same size consisting of only GBERT or GPT-2-Wechsel models. Our models were evaluated in the GermEval 2022 Shared Task on Text Complexity Assessment on data of German sentences. On out-of-sample data, our best ensemble achieved a root mean squared error of 0:435. Y1 - 2022 U6 - http://dx.doi.org/10.48550/arXiv.2209.04299 N1 - Proceedings of the 18th Conference on Natural Language Processing/Konferenz zur Verarbeitung natürlicher Sprache (KONVENS 2022) 12-15 September, 2022 University of Potsdam Potsdam, Germany SP - 57 EP - 62 PB - Association for Computational Linguistics CY - Potsdam ER - TY - THES A1 - Kannengießer, Justine T1 - Vom Airbag zum Rucksack mit Upcycling : Kampagne zur Steigerung der Bekanntheit der Marke Airpaq N2 - In der Automobilindustrie entsteht ein enormes Ausmaß an Abfall. Genau an dieser Stelle greift das Kölner Start-up Airpaq ein, das nachhaltige Rucksäcke und Accessoires aus Autoschrott unter fairen Arbeitsbedingungen in der EU herstellt. Das Ziel der Kampagne ist es, die Markenbekanntheit zu steigern und eine tiefergreifende und lang anhaltende Verbindung zur jungen Zielgruppe aufzubauen. Genau so, wie Airpaq den Taschen-Markt revolutioniert, stellt auch die junge Zielgruppe immer wieder Altbewährtes infrage. Mit der „HOLYSCRAP“-Bewegung ruft die Kampagne Upcycling-Abenteuer ins Leben. Die Kampagne ermutigt dazu, Teil der Upcycling-Community zu werden, um immer wieder neu und anders "schrottastische" Erlebnisse zu entdecken. So soll eingeladen werden, nicht nur beim Griff zur Tasche mal etwas Neues auszuprobieren, sondern auch bei allen gemeinsamen Aktivitäten, die man mit Airpaq erlebt. KW - Airpaq KW - Automobilbranche KW - nachhaltig KW - Kampagne KW - Rucksack Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Toma, Paul T1 - Scriptum : Geochronologische Darstellung der Schriftentstehung vom 33. Jh. v. Chr. bis heute N2 - Scriptum ist ein Interface mit Installationscharakter, welches die geschichtliche Entstehung von Schriftsystemen aus einer geochronologischen Perspektive darstellt. Die Installation wurde hauptsächlich für Museumsausstellungen konzipiert und besteht aus einer Wandprojektion, die durch iPads im Raum von mehreren Nutzern gleichzeitig gesteuert werden kann. Auf der Projektion sind alle 145 von Noto Sans unterstützten Schriftsysteme zu finden, die nach ihrer örtlichen Entstehung auf einer Weltkarte platziert wurden. Die Arbeit beruht auf dem wissenschaftlichen Datensatz aus dem Projekt „The World’s Writing Systems“ aufrufbar unter www.worldswritingsystems.org. Neben dem Informierungszweck dient die Installation auch als ein Ausrufezeichen für die Idee, dass Schrift ein wichtiger Aspekt unseres Kulturerbes ist und als ein Spiegel für die Evolution der Menschheit betrachtet werden kann. KW - Geschichte KW - Schriftsysteme KW - Typographie KW - Interaktiv KW - Interfacedesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Meesters, Elena T1 - Gestaltung eines häuslichen Telemonitoringsystems zur Prognose kardialer Dekompensation N2 - Herzinsuffizienz ist eine der häufigsten Herzerkrankungen in Deutschland. Sie ist fortschreitend und nicht heilbar. Der Krankheitsverlauf ist geprägt von plötzlichen, z.T. lebensbedrohlichen Verschlechterungen und Krankenhauseinweisungen, nach denen die Leistung des Herzen vermindert bleibt. Diese Dekompensationen lassen sich bisher im heimischen Umfeld nicht durch Messwerte vorhersehen. Dieses Gerät bestimmt die Flüssigkeitsansammlungen in der Lunge, die ein mittelfristiges Symptom einer Dekompensation sind. Außerdem misst es über einen Hautsensor die im Schweiß enthaltene Menge eines Proteins, das bei Überdehnung des Herzmuskels vermehrt im Blutplasma zu finden ist. So können Dekompensationen bis zu zwei Wochen vor einem akuten Ereignis detektiert und behandelt werden. Außerdem gibt es tagesformabhängige Tipps für die Alltagsgestaltung mit der Erkrankung. KW - Herzinusffizienz KW - Medizin KW - Herz KW - Gesundheit KW - Telemonitoring Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Schüller-Ruhl, Aaron A1 - Dinstühler, Leonard A1 - Senger, Thorsten A1 - Bergfeld, Stefan A1 - Ingenhag, Christian A1 - Fleischhaker, Robert ED - Mackenzie, Jacob T1 - Direct fabrication of arbitrary phase masks in optical glass via ultra-short pulsed laser writing of refractive index modifications JF - Applied Physics B N2 - We study the possibility to fabricate an arbitrary phase mask in a one-step laser-writing process inside the volume of an optical glass substrate. We derive the phase mask from a Gerchberg–Saxton-type algorithm as an array and create each individual phase shift using a refractive index modification of variable axial length. We realize the variable axial length by superimposing refractive index modifications induced by an ultra-short pulsed laser at different focusing depth. Each single modification is created by applying 1000 pulses with 15 μJ pulse energy at 100 kHz to a fixed spot of 25 μm diameter and the focus is then shifted axially in steps of 10 μm. With several proof-of-principle examples, we show the feasibility of our method. In particular, we identify the induced refractive index change to about a value of Δn=1.5⋅10−3. We also determine our current limitations by calculating the overlap in the form of a scalar product and we discuss possible future improvements. Y1 - 2022 U6 - http://dx.doi.org/10.1007/s00340-022-07928-2 SN - 1432-0649 (Online) SN - 0946-2171 (Print) N1 - Corresponding author: Robert Fleischhaker VL - 128 IS - Article number: 208 SP - 1 EP - 11 PB - Springer CY - Berlin ER - TY - JOUR A1 - Eggert, Mathias A1 - Kreuzer, Vincent T1 - Sprachsteuerung im Gesundheitswesen – Anforderungen und Auswahl geeigneter Anbieter T1 - Voice control in healthcare—requirements and provider selection JF - HMD Praxis der Wirtschaftsinformatik N2 - Das Gesundheitswesen ist konfrontiert mit steigenden Kosten und einer immer schwieriger werdenden Personalsituation. Zeitgleich versprechen moderne Sprachsteuerungssysteme Prozesse in Arztpraxen und Krankenhäusern zu verschlanken und Vorgänge zu beschleunigen. Dennoch wird derzeit der Einsatz von Sprachsteuerungssystemen in Arztpraxen oder Krankenhäusern nur selten beobachtet, was auch an den besonders strengen Datenschutzauflagen der Datenschutzgrundverordnung (DSGVO) liegt. Darüber hinaus wirft die niedrige Nutzungsrate die Frage nach den konkreten Anforderungen und ihrer Umsetzbarkeit auf, was durch den vorliegenden Beitrag adressiert wird, indem die Ergebnisse von Interviews mit acht medizinischen Fachexperten ausgewertet werden. Ergänzend wird die technische Umsetzbarkeit einzelner Anforderungen mit unterschiedlichen Cloud-Anbietern erprobt. KW - Gesundheitswesen KW - Sprachsteuerung KW - Sprachassistent KW - Anforderungen KW - Umsetzbarkeit Y1 - 2022 SN - 2198-2775 U6 - http://dx.doi.org/10.1365/s40702-022-00919-z SN - 1436-3011 N1 - Corresponding author: Mathias Eggert VL - 59 SP - 1640 EP - 1652 PB - Springer Vieweg CY - Wiesbaden ER -