TY - JOUR A1 - Waldvogel, Janice A1 - Freyler, Kathrin A1 - Helm, Michael A1 - Monti, Elena A1 - Stäudle, Benjamin A1 - Gollhofer, Albert A1 - Narici, Marco V. A1 - Ritzmann, Ramona A1 - Albracht, Kirsten T1 - Changes in gravity affect neuromuscular control, biomechanics, and muscle-tendon mechanics in energy storage and dissipation tasks JF - Journal of Applied Physiology N2 - This study evaluates neuromechanical control and muscle-tendon interaction during energy storage and dissipation tasks in hypergravity. During parabolic flights, while 17 subjects performed drop jumps (DJs) and drop landings (DLs), electromyography (EMG) of the lower limb muscles was combined with in vivo fascicle dynamics of the gastrocnemius medialis, two-dimensional (2D) kinematics, and kinetics to measure and analyze changes in energy management. Comparisons were made between movement modalities executed in hypergravity (1.8 G) and gravity on ground (1 G). In 1.8 G, ankle dorsiflexion, knee joint flexion, and vertical center of mass (COM) displacement are lower in DJs than in DLs; within each movement modality, joint flexion amplitudes and COM displacement demonstrate higher values in 1.8 G than in 1 G. Concomitantly, negative peak ankle joint power, vertical ground reaction forces, and leg stiffness are similar between both movement modalities (1.8 G). In DJs, EMG activity in 1.8 G is lower during the COM deceleration phase than in 1 G, thus impairing quasi-isometric fascicle behavior. In DLs, EMG activity before and during the COM deceleration phase is higher, and fascicles are stretched less in 1.8 G than in 1 G. Compared with the situation in 1 G, highly task-specific neuromuscular activity is diminished in 1.8 G, resulting in fascicle lengthening in both movement modalities. Specifically, in DJs, a high magnitude of neuromuscular activity is impaired, resulting in altered energy storage. In contrast, in DLs, linear stiffening of the system due to higher neuromuscular activity combined with lower fascicle stretch enhances the buffering function of the tendon, and thus the capacity to safely dissipate energy. KW - electromyography KW - locomotion KW - overload KW - stretch-shortening cycle KW - ultrasound Y1 - 2023 U6 - https://doi.org/10.1152/japplphysiol.00279.2022 SN - 1522-1601 (Onlineausgabe) SN - 8750-7587 (Druckausgabe) VL - 134 IS - 1 SP - 190 EP - 202 PB - American Physiological Society CY - Bethesda, Md. ER - TY - CHAP A1 - Fissabre, Anke A1 - Wilson, Ariane ED - Di Teodoro, Francesco P. ED - Ferretti, Emanuela ED - Frommel, Sabine ED - Schlimme, Hermann T1 - Hypotheses on the Tower of Monthoiron: A Built Design of Italian and Leonardian Inspiration in France T2 - Leonardo da Vinci: l’architettura / Léonard de Vinci : l’architecture Y1 - 2022 SN - 979-12-80956-00-2 N1 - Sprachen laut Verlagsangaben: Italienisch, Englisch, Französisch SP - 287 EP - 300 PB - Campisano Editore CY - Roma ER - TY - JOUR A1 - Heieis, Jule A1 - Böcker, Jonas A1 - D'Angelo, Olfa A1 - Mittag, Uwe A1 - Albracht, Kirsten A1 - Schönau, Eckhard A1 - Meyer, Andreas A1 - Voigtmann, Thomas A1 - Rittweger, Jörn T1 - Curvature of gastrocnemius muscle fascicles as function of muscle–tendon complex length and contraction in humans JF - Physiological Reports N2 - It has been shown that muscle fascicle curvature increases with increasing contraction level and decreasing muscle–tendon complex length. The analyses were done with limited examination windows concerning contraction level, muscle–tendon complex length, and/or intramuscular position of ultrasound imaging. With this study we aimed to investigate the correlation between fascicle arching and contraction, muscle–tendon complex length and their associated architectural parameters in gastrocnemius muscles to develop hypotheses concerning the fundamental mechanism of fascicle curving. Twelve participants were tested in five different positions (90°/105°*, 90°/90°*, 135°/90°*, 170°/90°*, and 170°/75°*; *knee/ankle angle). They performed isometric contractions at four different contraction levels (5%, 25%, 50%, and 75% of maximum voluntary contraction) in each position. Panoramic ultrasound images of gastrocnemius muscles were collected at rest and during constant contraction. Aponeuroses and fascicles were tracked in all ultrasound images and the parameters fascicle curvature, muscle–tendon complex strain, contraction level, pennation angle, fascicle length, fascicle strain, intramuscular position, sex and age group were analyzed by linear mixed effect models. Mean fascicle curvature of the medial gastrocnemius increased with contraction level (+5 m−1 from 0% to 100%; p = 0.006). Muscle–tendon complex length had no significant impact on mean fascicle curvature. Mean pennation angle (2.2 m−1 per 10°; p < 0.001), inverse mean fascicle length (20 m−1 per cm−1; p = 0.003), and mean fascicle strain (−0.07 m−1 per +10%; p = 0.004) correlated with mean fascicle curvature. Evidence has also been found for intermuscular, intramuscular, and sex-specific intramuscular differences of fascicle curving. Pennation angle and the inverse fascicle length show the highest predictive capacities for fascicle curving. Due to the strong correlations between pennation angle and fascicle curvature and the intramuscular pattern of curving we suggest for future studies to examine correlations between fascicle curvature and intramuscular fluid pressure. KW - biomechanics KW - connective tissue KW - physiology KW - ultrasound Y1 - 2023 U6 - https://doi.org/10.14814/phy2.15739 SN - 2051-817X VL - 11 IS - 11 SP - e15739, Seite 1-11 PB - Wiley ER - TY - CHAP A1 - Chavez Bermudez, Victor Francisco A1 - Cruz Castanon, Victor Fernando A1 - Ruchay, Marco A1 - Wollert, Jörg ED - Leipzig, Hochschule für Technik, Wirtschaft und Kultur T1 - Rapid prototyping framework for automation applications based on IO-Link T2 - Tagungsband AALE 2022: Wissenstransfer im Spannungsfeld von Autonomisierung und Fachkräftemangel N2 - The development of protype applications with sensors and actuators in the automation industry requires tools that are independent of manufacturer, and are flexible enough to be modified or extended for any specific requirements. Currently, developing prototypes with industrial sensors and actuators is not straightforward. First of all, the exchange of information depends on the industrial protocol that these devices have. Second, a specific configuration and installation is done based on the hardware that is used, such as automation controllers or industrial gateways. This means that the development for a specific industrial protocol, highly depends on the hardware and the software that vendors provide. In this work we propose a rapid-prototyping framework based on Arduino to solve this problem. For this project we have focused to work with the IO-Link protocol. The framework consists of an Arduino shield that acts as the physical layer, and a software that implements the IO-Link Master protocol. The main advantage of such framework is that an application with industrial devices can be rapid-prototyped with ease as its vendor independent, open-source and can be ported easily to other Arduino compatible boards. In comparison, a typical approach requires proprietary hardware, is not easy to port to another system and is closed-source. KW - Rapid-prototyping KW - Arduino KW - IO-Link KW - Industrial Communication Y1 - 2022 SN - 978-3-910103-00-9 U6 - https://doi.org/10.33968/2022.28 N1 - 18. AALE-Konferenz. Pforzheim, 09.03.-11.03.2022 CY - Leipzig ER - TY - CHAP A1 - Ulmer, Jessica A1 - Mostafa, Youssef A1 - Wollert, Jörg T1 - Digital Twin Academy: From Zero to Hero through individual learning experiences T2 - Tagungsband AALE 2022: Wissenstransfer im Spannungsfeld von Autonomisierung und Fachkräftemangel N2 - Digital twins are seen as one of the key technologies of Industry 4.0. Although many research groups focus on digital twins and create meaningful outputs, the technology has not yet reached a broad application in the industry. The main reasons for this imbalance are the complexity of the topic, the lack of specialists, and the unawareness of the twin opportunities. The project "Digital Twin Academy" aims to overcome these barriers by focusing on three actions: Building a digital twin community for discussion and exchange, offering multi-stage training for various knowledge levels, and implementing realworld use cases for deeper insights and guidance. In this work, we focus on creating a flexible learning platform that allows the user to select a training path adjusted to personal knowledge and needs. Therefore, a mix of basic and advanced modules is created and expanded by individual feedback options. The usage of personas supports the selection of the appropriate modules. KW - Digital Twins KW - Knowledge Transfer KW - Training Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bsz:l189-qucosa2-776097 SN - 978-3-910103-00-9 N1 - 18. AALE-Konferenz. Pforzheim, 09.03.-11.03.2022 SP - 1 EP - 9 ER - TY - CHAP A1 - Ulmer, Jessica A1 - Braun, Sebastian A1 - Wollert, Jörg T1 - Adaptive VR-Produktionsumgebungen für Evaluations- und Schulungstätigkeiten T1 - Adaptive VR production environments for evaluation and training purposes T2 - Automation 2021: Navigating towards resilient Production N2 - Industrie 4.0 stellt viele Herausforderungen an produzierende Unternehmen und ihre Beschäf-tigten. Innovative und effektive Trainingsstrategien sind erforderlich, um mit den sich schnell verändernden Produktionsumgebungen und neuen Fertigungstechnologien Schritt halten zu können. Virtual Reality (VR) bietet neue Möglichkeiten für On-the-Job, On-Demand- und Off-Premise-Schulungen. Diese Arbeit stellt ein neues VR Schulungssystem vor, welches sich flexible an unterschiedliche Trainingsobjekte auf Grundlage von Rezepten und CAD Modellen anpassen lässt. Das Konzept basiert auf gerichteten azyklischen Graphen und einem Level-system. Es ermöglicht eine benutzerindividuelle Lerngeschwindigkeit mittels visueller Ele-mente. Das Konzept wurde für einen mechanischen Anwendungsfall mit Industriekomponen-ten implementiert und in der Industrie 4.0-Modellfabrik der FH Aachen umgesetzt. N2 - Industry 4.0 poses many challenges for manufacturing companies and their employees. Inno-vative and effective training strategies are needed to keep pace with rapidly changing produc-tion environments and new manufacturing technologies. Virtual reality (VR) offers new oppor-tunities for on-the-job, on-demand, and off-premise training. This work presents a new VR training system that can be flexibly adapted to different training objects based on recipes and CAD models. The concept is based on directed acyclic graphs and a level system. It allows a user-individual learning speed by means of visual elements. The concept was implemented for a mechanical use case with industrial components and implemented in the industry 4.0 model factory of the FH Aachen University of Applied Sciences. Y1 - 2021 SN - 978-3-18-092392-5 U6 - https://doi.org/10.51202/9783181023921-55 SN - 0083-5560 N1 - 22. Leitkongress der Mess- und Automatisierungstechnik AUTOMATION 2021 - Navigating towards resilient Production, 29. und 30. Juni 2021 SP - 55 EP - 64 PB - VDI CY - Düsseldorf ER - TY - JOUR A1 - Kempt, Hendrik A1 - Freyer, Nils A1 - Nagel, Saskia K. T1 - Justice and the normative standards of explainability in healthcare JF - Philosophy & Technology N2 - Providing healthcare services frequently involves cognitively demanding tasks, including diagnoses and analyses as well as complex decisions about treatments and therapy. From a global perspective, ethically significant inequalities exist between regions where the expert knowledge required for these tasks is scarce or abundant. One possible strategy to diminish such inequalities and increase healthcare opportunities in expert-scarce settings is to provide healthcare solutions involving digital technologies that do not necessarily require the presence of a human expert, e.g., in the form of artificial intelligent decision-support systems (AI-DSS). Such algorithmic decision-making, however, is mostly developed in resource- and expert-abundant settings to support healthcare experts in their work. As a practical consequence, the normative standards and requirements for such algorithmic decision-making in healthcare require the technology to be at least as explainable as the decisions made by the experts themselves. The goal of providing healthcare in settings where resources and expertise are scarce might come with a normative pull to lower the normative standards of using digital technologies in order to provide at least some healthcare in the first place. We scrutinize this tendency to lower standards in particular settings from a normative perspective, distinguish between different types of absolute and relative, local and global standards of explainability, and conclude by defending an ambitious and practicable standard of local relative explainability. KW - Clinical decision support systems KW - Justice KW - Medical AI KW - Explainability KW - Normative standards Y1 - 2022 U6 - https://doi.org/10.1007/s13347-022-00598-0 VL - 35 IS - Article number: 100 SP - 1 EP - 19 PB - Springer Nature CY - Berlin ER - TY - CHAP A1 - Freyer, Nils A1 - Thewes, Dustin A1 - Meinecke, Matthias ED - Gusikhin, Oleg ED - Hammoudi, Slimane ED - Cuzzocrea, Alfredo T1 - GUIDO: a hybrid approach to guideline discovery & ordering from natural language texts T2 - Proceedings of the 12th International Conference on Data Science, Technology and Applications DATA - Volume 1 N2 - Extracting workflow nets from textual descriptions can be used to simplify guidelines or formalize textual descriptions of formal processes like business processes and algorithms. The task of manually extracting processes, however, requires domain expertise and effort. While automatic process model extraction is desirable, annotating texts with formalized process models is expensive. Therefore, there are only a few machine-learning-based extraction approaches. Rule-based approaches, in turn, require domain specificity to work well and can rarely distinguish relevant and irrelevant information in textual descriptions. In this paper, we present GUIDO, a hybrid approach to the process model extraction task that first, classifies sentences regarding their relevance to the process model, using a BERT-based sentence classifier, and second, extracts a process model from the sentences classified as relevant, using dependency parsing. The presented approach achieves significantly better resul ts than a pure rule-based approach. GUIDO achieves an average behavioral similarity score of 0.93. Still, in comparison to purely machine-learning-based approaches, the annotation costs stay low. KW - Natural Language Processing KW - Text Mining KW - Process Model Extraction KW - Business Process Intelligence Y1 - 2023 SN - 978-989-758-664-4 U6 - https://doi.org/10.5220/0012084400003541 SN - 2184-285X N1 - 12th International Conference on Data Science, Technology and Applications, July 11-13, 2023, in Rome, Italy. SP - 335 EP - 342 ER - TY - CHAP A1 - Klöser, Lars A1 - Büsgen, André A1 - Kohl, Philipp A1 - Kraft, Bodo A1 - Zündorf, Albert ED - Conte, Donatello ED - Fred, Ana ED - Gusikhin, Oleg ED - Sansone, Carlo T1 - Explaining relation classification models with semantic extents T2 - Deep Learning Theory and Applications N2 - In recent years, the development of large pretrained language models, such as BERT and GPT, significantly improved information extraction systems on various tasks, including relation classification. State-of-the-art systems are highly accurate on scientific benchmarks. A lack of explainability is currently a complicating factor in many real-world applications. Comprehensible systems are necessary to prevent biased, counterintuitive, or harmful decisions. We introduce semantic extents, a concept to analyze decision patterns for the relation classification task. Semantic extents are the most influential parts of texts concerning classification decisions. Our definition allows similar procedures to determine semantic extents for humans and models. We provide an annotation tool and a software framework to determine semantic extents for humans and models conveniently and reproducibly. Comparing both reveals that models tend to learn shortcut patterns from data. These patterns are hard to detect with current interpretability methods, such as input reductions. Our approach can help detect and eliminate spurious decision patterns during model development. Semantic extents can increase the reliability and security of natural language processing systems. Semantic extents are an essential step in enabling applications in critical areas like healthcare or finance. Moreover, our work opens new research directions for developing methods to explain deep learning models. KW - Relation classification KW - Natural language processing KW - Natural language understanding KW - Information extraction KW - Trustworthy artificial intelligence Y1 - 2023 SN - 978-3-031-39058-6 (Print) SN - 978-3-031-39059-3 (Online) U6 - https://doi.org/10.1007/978-3-031-39059-3_13 N1 - 4th International Conference, DeLTA 2023, Rome, Italy, July 13–14, 2023. SP - 189 EP - 208 PB - Springer CY - Cham ER - TY - INPR A1 - Greiner, Lasse A1 - Jeromin, Günter Erich A1 - Sithole, Patience A1 - Petersen, Soenke T1 - Preprint: Studies on the enzymatic reduction of levulinic acid using Chiralidon-R and Chiralidon-S T2 - ChemRxiv N2 - The enzymatic reduction of levulinic acid by the chiral catalysts Chiralidon-R and Chiralidon-S which are commercially available superabsorbed alcohol dehydrogenases is described. The Chiralidon®-R/S reduces the levulinic acid to the (R,S)-4-hydroxy valeric acid and the (R)- or (S)- gamma-valerolactone. KW - Levulinic acid KW - Chiralidon-R KW - Chiralidon-S KW - 4-hydroxy valeric acid KW - (R)- or (S)- gamma-valerolactone Y1 - 2023 U6 - https://doi.org/10.26434/chemrxiv-2023-jlvcv ER - TY - JOUR A1 - Cheng, Chi-Tsun A1 - Wollert, Jörg A1 - Chen, Xi A1 - Fapojuwo, Abraham O. T1 - Guest Editorial : Circuits and Systems for Industry X.0 Applications JF - IEEE Journal on Emerging and Selected Topics in Circuits and Systems Y1 - 2023 U6 - https://doi.org/10.1109/JETCAS.2023.3278843 SN - 2156-3357 (Print) SN - 2156-3365 (Online) VL - 13 SP - 457 EP - 460 PB - IEEE CY - New York ET - 2 ER - TY - RPRT A1 - Göll, Fabian A1 - Braunstein, Björn A1 - Albracht, Kirsten T1 - Lernende roboterassistierte Systeme für das neuromuskuläre Training - RoSylerNT; Teilvorhaben: Entwicklung eines neuromuskuloskelettalen Modells als Basis für die Interaktionsfähigkeiten autonomer Assistenzsysteme KW - Robotik KW - Rehabilitationsmedizin KW - Neuromuskuläres System KW - Rehabilitatives Training KW - Trainingsgerät Y1 - 2021 U6 - https://doi.org/10.2314/KXP:1855318741 N1 - Förderkennzeichen BMBF 16SV7853 Schlussbericht der Deutschen Sporthochschule Köln für das Vorhaben RoSylerNT Laufzeit: 01.08.2017-31.07.2021 PB - Deutsche Sporthochschule Köln CY - Köln ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Regelung der Einstellung des Bachelorstudiengangs Bauingenieurwesen – Netzingenieur (7-semestrig) und des dualen Bachelorstudiengangs Bauingenieurwesen – Netzingenieur (9-semestrig) im Fachbereich Bauingeieurwesen an der Fachhochschule Aachen T3 - FH-Mitteilungen - 79/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Einstellungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Studien- und Prüfungsordnung für den Masterstudiengang Bauingenieurwesen – Abschluss Master of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen T3 - FH-Mitteilungen - 80/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Masterstudiengang „Bauingenieurwesen“ vom 10. Dezember 2012 (FH-Mitteilung Nr. 129/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 30. Mai 2017 (FH-Mitteilung Nr. 58/2017) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 81/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Studien- und Prüfungsordnung für den Masterstudiengang Facility Management – Abschluss Master of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen T3 - FH-Mitteilungen - 82/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Masterstudiengang „Facility Management“ vom 29. November 2012 (FH-Mitteilung Nr. 127/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 3. Februar 2016 (FH-Mitteilung Nr. 10/2016) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 83/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Master KW - Facility Management Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Bachelorstudiengang Bauingenieurwesen (7-semestrig), Bachelorstudiengang Bauingenieurwesen mit Praxissemester (8-semestrig) und Bachelorstudiengang Bauingenieurwesen mit Auslandssemester (8-semestrig) Abschluss Bachelor of Engineering T3 - FH-Mitteilungen - 84/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge „Elektrotechnik“ und „Elektrotechnik mit Praxissemester“ im Fachbereich Energietechnik an der FH Aachen : vom 10. Oktober 2019 T3 - FH-Mitteilungen - 99/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Bachelor KW - Elektrotechnik KW - Energietechnik Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Gesamtprüfungsordnung für den Bachelorstudiengang „Elektrotechnik mit Orientierungssemester“ an der Fachhochschule Aachen und der RWTH Aachen : vom 10. Oktober 2019 T3 - FH-Mitteilungen - 100/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Gesamtprüfungsordnung KW - Bachelor KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - Gesamtprüfungsordnung für den Bachelorstudiengang „Elektrotechnik mit Orientierungssemester“ an der Fachhochschule Aachen und der RWTH Aachen : vom 21. November 2018 – FH-Mitteilung Nr. 165/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 10. Oktober 2019 – FH-Mitteilung Nr. 100/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 101/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Gesamtprüfungsordnung KW - Bachelor KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Prüfungsordnung für den Masterstudiengang „Wirtschaftsingenieurwesen“ an der Fachhochschule Aachen : vom 14. Oktober 2019 T3 - FH-Mitteilungen - 102/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Master KW - Wirtschaftsingenieurwesen Y1 - 2023 ER - TY - GEN T1 - Prüfungsordnung für den Masterstudiengang „Wirtschaftsingenieurwesen“ an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 152/2014 in der Fassung der bekanntmachung der Änderungsordnung vom 14. Oktober 2019 – FH-Mitteilung Nr. 102/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 103/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Wirtschaftsingenieurwesen Y1 - 2019 ER - TY - JOUR A1 - Timme, Michael T1 - Bauliche Veränderungen durch Wohnungseigentümer und die Zustimmung der Gemeinschaft : Zugleich eine Besprechung des BGH, Urt. v. 17.3.2023 – V ZR 140/22, MDR 2023, 619 JF - Monatsschrift für Deutsches Recht N2 - Durch das WEMoG (Gesetz v. 16.10.2020, BGBl. I 2187) hat der Gesetzgeber die Regelung des § 20 WEG eingeführt. Demnach ist auch für bauliche Veränderungen an Räumen und Flächen, die einem Sondernutzungsrecht unterliegen, die Zustimmung der Gemeinschaft notwendig. Der BGH hat nun mit Urt. v. 17.3.2023 –V ZR 140/22, MDR 2023, 619 deutlich gemacht, dass bei Fehlen eines entsprechenden Beschlusses, die bauliche Veränderung durch einen einzelnen Wohnungseigentümer nicht vorgenommen werden darf, sondern eine rechtswidrige Eigentumsbeeinträchtigung darstellt. Der folgende Beitrag nimmt die Entscheidung zum Anlass, um die neue Rechtslage durch § 20 WEG eingehend zu erläutern. Gleichzeitig werden die Folgen der aktuellen Entscheidung näher dargestellt. Y1 - 2023 SN - 2194-4202 (online) SN - 0340-1812 (print) VL - 77 IS - 13 SP - 815 EP - 818 PB - Verlag Dr. Otto Schmidt CY - Köln ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Bachelorstudiengang Bauingenieurwesen (7-semestrig), Bachelorstudiengang Bauingenieurwesen mit Praxissemester (8-semestrig), Bachelorstudiengang Bauingenieurwesen mit Auslandssemester (8-semestrig) Abschluss Bachelor of Engineering : vom 1. September 2011 – FH-Mitteilung Nr. 76/2011 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 74/2019 (Nichtamtliche lesbare Fassung, Studienbeginn WS 2016/17–2017/18) T3 - FH-Mitteilungen - 85/2019 KW - Amtliche Mitteilung KW - Studien- und Prüfungsordnung KW - Lesbare Fassung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für die Bachelorstudiengänge „Bauingenieurwesen“ (7-semestrig), „Bauingenieurwesen mit Praxissemester“ (8-semestrig) und „Bauingenieurwesen mit Auslandssemester“ (8-semestrig) vom 1. September 2011 (FH-Mitteilung Nr. 76/2011) in der Fassung der Bekanntmachung der Änderungsordnungen vom 22. August 2013 (FH-Mitteilung Nr. 88/2013), 8. Juni 2016 (FH-Mitteilung Nr. 80/2016) und 16. August 2019 (FH-Mitteilung Nr. 74/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 119/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 75/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 86/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung des Studiengangs Holzingenieurwesen (7-semestrig) – Abschluss Bachelor of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 66/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 76/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 87/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Bachelorstudiengang „Holzingenieurwesen“ (7-semestrig) vom 16. Juli 2012 (FH-Mitteilung Nr. 66/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 6. Juli 2016 (FH-Mitteilung Nr. 95/2016) und 16. August 2019 (FH-Mitteilung Nr. 76/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 120/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 77/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 88/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung des Studiengangs Bauingenieurwesen – Netzingenieur – Abschluss Bachelor of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung | Studienbeginn WS 2011/12–2013/14) T3 - FH-Mitteilungen - 89/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den dualen Bachelorstudiengang Bauingenieurwesen – Netzingenieur (9 Semester) und den Bachelorstudiengang Bauingenieurwesen – Netzingenieur (7 Semester) Abschluss Bachelor of Engineering im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung, Studienbeginn WS 2014/15–2016/17) T3 - FH-Mitteilungen - 90/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den dualen Bachelorstudiengang Bauingenieurwesen – Netzingenieur (9 Semester) und den Bachelorstudiengang Bauingenieurwesen – Netzingenieur (7 Semester) Abschluss Bachelor of Engineering im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung, Studienbeginn ab WS 2017/18) T3 - FH-Mitteilungen - 91/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Regelung der Einstellung des Bachelorstudiengangs Bauingenieurwesen – Netzingenieur (7-semestrig) und des dualen Bachelorstudiengangs Bauingenieurwesen – Netzingenieur (9-semestrig) im Fachbereich Bauingeieurwesen an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 123/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 79/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 92/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Einstellungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Masterstudiengang Bauingenieurwesen – Abschluss Master of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 10. Dezember 2012 – FH-Mitteilung Nr. 129/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 80/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 93/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Masterstudiengang „Bauingenieurwesen“ vom 10. Dezember 2012 (FH-Mitteilung Nr. 129/2012) in der Fassung der Bekanntmachung der Änderungsordnung vom 30. Mai 2017 (FH-Mitteilung Nr. 58/2017) und 16. August 2019 (FH-Mitteilung Nr. 80/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 121/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 81/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 94/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Masterstudiengang Facility Management – Abschluss Master of Engineering – : vom 29. November 2012 – FH-Mitteilung Nr. 127/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 82/2019 (Nichtamtliche lesbare Fassung, Studienbeginn WS 2012/13–SS 2016) T3 - FH-Mitteilungen - 95/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Facility Management Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den dreisemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 154/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 5/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab SS 2016) T3 - FH-Mitteilungen - 104/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den dreisemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 154/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 5/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2017/18) T3 - FH-Mitteilungen - 105/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den viersemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11.Dezember 2014 – FH-Mitteilung Nr. 156/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 6/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2015/16) T3 - FH-Mitteilungen - 106/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den viersemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11.Dezember 2014 – FH-Mitteilung Nr. 156/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 6/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2017/18) T3 - FH-Mitteilungen - 107/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den viersemestrigen Masterstudiengang „Industrial Engineering“ Fachbereich Wirtschaftswissenschaften Fachbereich Maschinenbau und Mechatronik an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 156/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 6/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2018/19) T3 - FH-Mitteilungen - 108/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - 4. Ordnung zur Änderung der Zugangsordnung für den Masterstudiengang Elektrotechnik im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 5. November 2019 T3 - FH-Mitteilungen - 109/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Zugangsordnung KW - Master KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - Zugangsordnung für die Masterstudiengänge „Elektrotechnik“ und „Elektrotechnik (Teilzeit)“ im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 22. Januar 2010 – FH-Mitteilung Nr. 6/2010 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. November 2019 – FH-Mitteilung Nr. 109/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 110/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Zugangsordnung KW - Master KW - Elektrotechnik Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Masterstudiengänge „Elektrotechnik“ und „Elektrotechnik (Teilzeit)“ im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 5. November 2019 T3 - FH-Mitteilungen - 111/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Elektrotechnik KW - Elektrotechnik (Teilzeit) Y1 - 2019 ER - TY - GEN T1 - 4. Ordnung zur Änderung der Zugangsordnung für den Masterstudiengang Information Systems Engineering im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 5. November 2019 T3 - FH-Mitteilungen - 112/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Zugangsordnung KW - Master KW - Information Systems Engineering Y1 - 2019 ER - TY - GEN T1 - Zugangsordnung für die Masterstudiengänge „Information Systems Engineering“ und „Information Systems Engineering (Teilzeit)“ im Fachbereich Elektrotechnik und Informationstechnik an der Fachhochschule Aachen : vom 22. Januar 2010 – FH-Mitteilung Nr. 4/2010 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. November 2019 – FH-Mitteilung Nr. 112/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 113/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Zugangsordnung KW - Master KW - Information Systems Engineering Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für die Bachelorstudiengänge „Schienenfahrzeugtechnik“ „Schienenfahrzeugtechnik (Teilzeit)“ und „Dualer Studiengang Schienenfahrzeugtechnik (DIRail)“ im Fachbereich Maschinenbau und Mechatronik an der Fachhochschule Aachen T3 - FH-Mitteilungen - 70/2019 KW - Amtliche Mitteilung KW - Bachelor KW - Prüfungsordnung KW - Änderungsordnung KW - Maschinenbau und Mechatronik Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge „Schienenfahrzeugtechnik“ „Schienenfahrzeugtechnik (Teilzeit)“ und „Dualer Studiengang Schienenfahrzeugtechnik (DIRail)“ im Fachbereich Maschinenbau und Mechatronik an der Fachhochschule Aachen T3 - FH-Mitteilungen - 71/2019 KW - Prüfungsordnung KW - Bachelor KW - Maschinenbau und Mechatronik KW - lesbare Fassung Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Prüfungsordnung für den dualen ausbildungsintegrierenden Bachelorstudiengang „Physiotherapie“ und den berufsbegleitenden Bachelorstudiengang „Physiotherapie“ an der Fachhochschule Aachen in Kooperation mit der Medizinischen Fakultät der Rheinisch-Westfälisch Technischen Hochschule Aachen und der Physiotherapieschule des Universitätsklinikums Aachen (UK Aachen) T3 - FH-Mitteilungen - 72/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Bachelor KW - Prüfungsordnung KW - Physiotherapie Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den dualen ausbildungsintegrierenden Bachelorstudiengang „Physiotherapie“ und den berufsbegleitenden Bachelorstudiengang „Physiotherapie“ an der Fachhochschule Aachen in Kooperation mit der Medizinischen Fakultät der Rheinisch-Westfälisch Technischen Hochschule Aachen und der Physiotherapieschule des Universitätsklinikums Aachen (UK Aachen) T3 - FH-Mitteilungen - 73/2019 KW - Amtliche Mitteilung KW - Bachelor KW - Prüfungsordnung KW - lesbare Fassung KW - Physiotherapie Y1 - 2019 ER - TY - GEN T1 - 3. Ordnung zur Änderung der Studien- und Prüfungsordnung für den Bachelorstudiengang Bauingenieurwesen (7-semestrig), Bachelorstudiengang Bauingenieurwesen mit Praxissemester (8-semestrig), Bachelorstudiengang Bauingenieurwesen mit Auslandssemester (8-semestrig), Abschluss Bachelor of Engineering T3 - FH-Mitteilungen - 74/2019 KW - Studien- und Prüfungsordnung KW - Änderungsordnung KW - Bachelor KW - Bauingieurwesen KW - Amtliche Mitteilung Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für die Bachelorstudiengänge „Bauingenieurwesen“ (7-semestrig), „Bauingenieurwesen mit Praxissemester“ (8-semestrig) und „Bauingenieurwesen mit Auslandssemester“ (8-semestrig) vom 1. September 2011 (FH-Mitteilung Nr. 76/2011) in der Fassung der Bekanntmachung der Änderungsordnungen vom 22. August 2013 (FH- Mitteilung Nr. 88/2013) und vom 8. Juni 2016 (FH-Mitteilung Nr. 80/2016) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 75/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studiengangs- und Prüfungsordnung KW - Bauingenieurwesen KW - Bachelor Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für die Bachelorstudiengänge „Bauingenieurwesen“ (7-semestrig), „Bauingenieurwesen mit Praxissemester“ (8-semestrig) und „Bauingenieurwesen mit Auslandssemester“ (8-semestrig) vom 1. September 2011 (FH-Mitteilung Nr. 76/2011) in der Fassung der Bekanntmachung der Änderungsordnungen vom 22. August 2013 (FH- Mitteilung Nr. 88/2013) und vom 8. Juni 2016 (FH-Mitteilung Nr. 80/2016) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 76/2019 KW - Amtliche Mitteilung KW - Studien- und Prüfungsordnung KW - Änderungsordnung KW - Holzingenieurwesen KW - Bachelor Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Bachelorstudiengang „Holzingenieurwesen“ (7-semestrig) vom 16. Juli 2012 (FH-Mitteilung Nr. 66/2012) in der Fassung der Bekanntmachung der Änderungsordnung vom 6. Juli 2016 (FH-Mitteilung Nr. 95/2016) an der Fachhochschule Aachen T3 - FH-Mitteilungen - 77/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Holzingenieurwesen KW - Bachelor Y1 - 2019 ER - TY - GEN T1 - 3. Ordnung zur Änderung der Studien- und Prüfungsordnung für den dualen Bachelorstudiengang Bauingenieurwesen, Netzingenieur (9 Semester) und den Bachelorstudiengang Bauingenieurwesen – Netzingenieur (7 Semester) Abschluss Bachelor of Engineering im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen T3 - FH-Mitteilungen - 78/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Masterstudiengang Facility Management – Abschluss Master of Engineering – : vom 29. November 2012 – FH-Mitteilung Nr. 127/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 82/2019 (Nichtamtliche lesbare Fassung | Studienbeginn WS 2016/17–SS 2018) T3 - FH-Mitteilungen - 96/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Facility Management Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Masterstudiengang „Facility Management“ vom 29. November 2012 (FH-Mitteilung Nr. 127/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 3. Februar 2016 (FH-Mitteilung Nr. 10/2016) und 16. August 2019 (FH-Mitteilung Nr. 82/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 122/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 83/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 97/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Master KW - Facility Management Y1 - 2019 ER - TY - GEN T1 - Beitragsordnung des Studierendenwerks Aachen (21. Änderung) : vom 3. Juli 2019 T3 - FH-Mitteilungen - 98/2019 KW - Amtliche Mitteilung KW - Beitragsordnung KW - Studierendenwerk Y1 - 2019 ER - TY - JOUR A1 - Lepke, Dietrich A1 - Lillie, Dirk A1 - Peterson, Leif Arne A1 - Hempe, Thomas T1 - Liegedauer von Holzschwellen in Tunneln der Hamburger Hochbahn AG JF - EI - Der Eisenbahningenieur N2 - Die Hamburger Hochbahn AG benötigte im Rahmen der Überarbeitung einer langfristigen Instandhaltungs- und Erneuerungsstrategie für ihre U-Bahn-Infrastruktur eine belastbare Aussage über die Restlebensdauer der Holzschwellen im Tunnel. Aus diesem Grunde beauftragte sie das Institut für Verkehrswesen, Eisenbahnbau und -betrieb (IVE) der Universität Hannover mit der Erstellung eines entsprechenden Gutachtens. Das Ergebnis führte zu der gesicherten Aussage einer erheblich längeren Restlebensdauer der Tunnelschwellen gegenüber den bisherigen, geschätzten Annahmen. Y1 - 2006 SN - 0013-2810 IS - 2 SP - 46 EP - 50 PB - DVV Media Group CY - Hamburg ER - TY - THES A1 - Peterson, Leif Arne T1 - Zum Tragverhalten nachgiebig verbundener Biegeträger aus Holz N2 - In der vorliegenden Dissertation werden zunächst die linear elastischen Bemessungsmöglichkeiten für nachgiebig verbundene Biegeträger unter statischer und dynamischer Beanspruchung diskutiert. Zum Vergleich wurden praktische Untersuchungen an zweiteiligen Kantholzbiegeträgem mit mechanischen Verbindungsmitteln unterschiedlicher Verformungscharakteristika durchgeführt, ebenso wie umfangreiche Materialprüfungen an den zusammengefügten Einzelquerschnitten. Hierdurch werden die Unterschiede zum realen, nicht elastischen, statischen Tragverhalten aufgezeigt. Der für das dynamische Verhalten maßgebende Systemparameter der Eigenfrequenz wird für mehrteilige Biegeträger theoretisch hinterfragt und an den nachgiebig verbundenen Kantholzbiegeträgem gemessen. Begleitet von weiteren praktischen Untersuchungen an einzelnen Verbindungsmitteln unter Blockscherbeanspruchung wird die rechnerische Berücksichtigung des plastischen Verbindungsmittelverhaltens auf zwei theoretischen Wegen erforscht. Auf Grundlage der Untersuchungen wird ein neues, semianalytisches y-Verfahren entwickelt. Gegenüber den Berechnungen mit finiten Volumen- und Kontakt-Elementen erweist sich das neue Verfahren auf Basis der, um die schubweichen Fugen erweiterten, Balkentheorie als leistungsfähiger. Der Einfluss des plastischen Verbindungsmittelverhaltens wird durch vergleichende Parameterstudien mit diesem neuen Verfahren als vom anerkannten Stand der Technik ausreichend berücksichtigt identifiziert. Für die linear elastische Dimensionierung werden optimierte Verbindungsmittelanordnungen hergeleitet, die durch übersichtliche Ergänzungen zum existierenden Bemessungskonzept des y-Verfahrens eine exaktere Berechnung ermöglichen. Y1 - 2008 SN - 9783816775973 N1 - Berichte des Instituts für Bauphysik, Band 1 PB - Fraunhofer IRB Verlag CY - Stuttgart ER - TY - JOUR A1 - Nabil, F. A1 - Peterson, Leif Arne A1 - Schmidt, A. A1 - Geerdes, D. T1 - Die Holzkuppel des Neuen Palais in Potsdam JF - Bauingenieur Y1 - 2010 SN - 0005-6650 VL - 85 IS - 8 SP - 324 EP - 330 PB - Springer-VDI-Verlag CY - Düsseldorf ER - TY - BOOK A1 - Nebgen, Nikolaus A1 - Peterson, Leif Arne T1 - Holzbau kompakt nach Eurocode 5 N2 - "Holzbau kompakt" wurde sowohl für Studierende als auch Praktiker konzipiert und beschränkt sich nicht auf reine Holzbauaufgaben, sondern setzt sich ggf. auch mit der Tragwerkslehre auseinander. Die Neuauflage basiert auf dem Eurocode 5 und berücksichtigt zahlreiche neue Erkenntnisse aus Forschung und praxisnaher Entwicklung. Neben den Grundlagen der Bemessung, der Baustoffe, der Dauerhaftigkeit und des Brandschutzes konzentriert sich das Grundlagenwerk besonders auf das Konstruieren mit Holz und Holzwerkstoffen, anschaulich dargestellt an sehr ausführlichen Beispielen für Wohnhaus und Hallentragwerk. Y1 - 2015 SN - 978-3-410-25455-3 PB - Beuth CY - Berlin ET - 5. Auflage ER - TY - BOOK A1 - Holschemacher, Klaus A1 - Peters, Klaus A1 - Peterson, Leif Arne A1 - Schneider, Klaus-Jürgen A1 - Thiele, Ralf T1 - Konstruktiver Ingenieurbau kompakt: Formelsammlung und Bemessungshilfen nach Eurocode für die Bereiche: Lastannahmen, Holzbau, Mauerwerksbau, Stahlbau, Stahlbetonbau, Geotechnik, statische Hinweise N2 - Das kompakte Nachschlagewerk für den konstruktiven Ingenieurbau wurde für den täglichen Gebrauch auf der Baustelle konzipiert und stellt alle für die rechnerische Nachweisführung und Konstruktion von Bauteilen wichtigsten Angaben in Form einer Formelsammlung mit Nachweishilfen zur Verfügung. Der Inhalt wurde auf Basis der neuen Eurocodes komplett aktualisiert und erweitert. Die 4. Auflage enthält in bewährter Manier eine umfangreiche Formelsammlung, Querschnittswerte und Bemessungshilfen zu den Bereichen Lastannahmen, Holzbau, Mauerwerksbau, Stahlbau, Stahlbetonbau, Geotechnik sowie statische Hinweise. Farbiges Papier erleichtert den zielgerichteten Zugriff auf die einzelnen Fachgebiete. Y1 - 2013 SN - 978-3-410-22775-5 PB - Beuth CY - Berlin ET - 4., vollständig überarbeitete Auflage ER - TY - CHAP A1 - Frühwald, Katja A1 - Peterson, Leif Arne A1 - Hasenstab, Andreas ED - Fouad, Nabil A. T1 - Prüfverfahren zur Begutachtung der Materialeigenschaften von Holztragwerken T2 - Bauphysik‐Kalender 2012: Schwerpunkt: Gebäudediagnostik N2 - Dieses Kapitel beinhaltet: - Einleitung - Ausgewählte typische Schäden an Holzbauwerken - Das Material Holz und seine Besonderheiten - Bestandserfassung - Labormethoden - Begutachtungsbeispiele - Zusammenfassung und Schlussfolgerungen - Literatur Y1 - 2012 SN - 9783433029862 (Print) SN - 9783433601235 (Online) U6 - https://doi.org/10.1002/9783433601235.ch4 SP - 103 EP - 155 PB - Ernst & Sohn CY - Berlin ER - TY - JOUR A1 - Özsoylu, Dua A1 - Aliazizi, Fereshteh A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Template bacteria-free fabrication of surface imprinted polymer-based biosensor for E. coli detection using photolithographic mimics: Hacking bacterial adhesion JF - Biosensors and Bioelectronics N2 - As one class of molecular imprinted polymers (MIPs), surface imprinted polymer (SIP)-based biosensors show great potential in direct whole-bacteria detection. Micro-contact imprinting, that involves stamping the template bacteria immobilized on a substrate into a pre-polymerized polymer matrix, is the most straightforward and prominent method to obtain SIP-based biosensors. However, the major drawbacks of the method arise from the requirement for fresh template bacteria and often non-reproducible bacteria distribution on the stamp substrate. Herein, we developed a positive master stamp containing photolithographic mimics of the template bacteria (E. coli) enabling reproducible fabrication of biomimetic SIP-based biosensors without the need for the “real” bacteria cells. By using atomic force and scanning electron microscopy imaging techniques, respectively, the E. coli-capturing ability of the SIP samples was tested, and compared with non-imprinted polymer (NIP)-based samples and control SIP samples, in which the cavity geometry does not match with E. coli cells. It was revealed that the presence of the biomimetic E. coli imprints with a specifically designed geometry increases the sensor E. coli-capturing ability by an “imprinting factor” of about 3. These findings show the importance of geometry-guided physical recognition in bacterial detection using SIP-based biosensors. In addition, this imprinting strategy was employed to interdigitated electrodes and QCM (quartz crystal microbalance) chips. E. coli detection performance of the sensors was demonstrated with electrochemical impedance spectroscopy (EIS) and QCM measurements with dissipation monitoring technique (QCM-D). KW - Surface imprinted polymer KW - E. coli detection KW - Photolithographic mimics KW - Master stamp KW - Quartz crystal microbalance Y1 - 2024 U6 - https://doi.org/10.1016/j.bios.2024.116491 SN - 1873-4235 (eISSN) SN - 0956-5663 N1 - Corresponding author: Michael J. Schöning VL - 261 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Ketelhut, Maike A1 - Brügge, G. M. A1 - Göll, Fabian A1 - Braunstein, Bjoern A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Adaptive iterative learning control of an industrial robot during neuromuscular training JF - IFAC PapersOnLine N2 - To prevent the reduction of muscle mass and loss of strength coming along with the human aging process, regular training with e.g. a leg press is suitable. However, the risk of training-induced injuries requires the continuous monitoring and controlling of the forces applied to the musculoskeletal system as well as the velocity along the motion trajectory and the range of motion. In this paper, an adaptive norm-optimal iterative learning control algorithm to minimize the knee joint loadings during the leg extension training with an industrial robot is proposed. The response of the algorithm is tested in simulation for patients with varus, normal and valgus alignment of the knee and compared to the results of a higher-order iterative learning control algorithm, a robust iterative learning control and a recently proposed conventional norm-optimal iterative learning control algorithm. Although significant improvements in performance are made compared to the conventional norm-optimal iterative learning control algorithm with a small learning factor, for the developed approach as well as the robust iterative learning control algorithm small steady state errors occur. KW - Iterative learning control KW - Robotic rehabilitation KW - Adaptive control Y1 - 2020 U6 - https://doi.org/10.1016/j.ifacol.2020.12.741 SN - 2405-8963 VL - 53 IS - 2 SP - 16468 EP - 16475 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Ketelhut, Maike A1 - Kolditz, Melanie A1 - Göll, Fabian A1 - Braunstein, Bjoern A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Admittance control of an industrial robot during resistance training JF - IFAC-PapersOnLine N2 - Neuromuscular strength training of the leg extensor muscles plays an important role in the rehabilitation and prevention of age and wealth related diseases. In this paper, we focus on the design and implementation of a Cartesian admittance control scheme for isotonic training, i.e. leg extension and flexion against a predefined weight. For preliminary testing and validation of the designed algorithm an experimental research and development platform consisting of an industrial robot and a force plate mounted at its end-effector has been used. Linear, diagonal and arbitrary two-dimensional motion trajectories with different weights for the leg extension and flexion part are applied. The proposed algorithm is easily adaptable to trajectories consisting of arbitrary six-dimensional poses and allows the implementation of individualized trajectories. KW - Assistive technology KW - Rehabilitation engineering KW - Human-Computer interaction KW - Automatic control Y1 - 2019 U6 - https://doi.org/10.1016/j.ifacol.2019.12.102 SN - 2405-8963 N1 - 14th IFAC Symposium on Analysis, Design, and Evaluation of Human Machine Systems HMS 2019 Tallinn, Estonia, 16–91 September 2019 VL - 52 IS - 19 SP - 223 EP - 228 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Ketelhut, Maike A1 - Göll, Fabian A1 - Braunstein, Bjoern A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Iterative learning control of an industrial robot for neuromuscular training T2 - 2019 IEEE Conference on Control Technology and Applications N2 - Effective training requires high muscle forces potentially leading to training-induced injuries. Thus, continuous monitoring and controlling of the loadings applied to the musculoskeletal system along the motion trajectory is required. In this paper, a norm-optimal iterative learning control algorithm for the robot-assisted training is developed. The algorithm aims at minimizing the external knee joint moment, which is commonly used to quantify the loading of the medial compartment. To estimate the external knee joint moment, a musculoskeletal lower extremity model is implemented in OpenSim and coupled with a model of an industrial robot and a force plate mounted at its end-effector. The algorithm is tested in simulation for patients with varus, normal and valgus alignment of the knee. The results show that the algorithm is able to minimize the external knee joint moment in all three cases and converges after less than seven iterations. KW - Knee KW - Training KW - Load modeling KW - Force KW - Iterative learning control Y1 - 2019 SN - 978-1-7281-2767-5 (ePub) SN - 978-1-7281-2766-8 (USB) SN - 978-1-7281-2768-2 (PoD) U6 - https://doi.org/10.1109/CCTA.2019.8920659 N1 - 2019 IEEE Conference on Control Technology and Applications (CCTA) Hong Kong, China, August 19-21, 2019 PB - IEEE CY - New York ER - TY - GEN A1 - Blottner, Dieter A1 - Hastermann, Maria A1 - Muckelt, Paul A1 - Albracht, Kirsten A1 - Schoenrock, Britt A1 - Salanova, Michele A1 - Warner, Martin A1 - Gunga, Hans-Christian A1 - Stokes, Maria T1 - MYOTONES - Inflight muscle health status monitoring during long-duration space missions onboard the International Space Station: a single case study T2 - IAC Papers Archive N2 - The MYOTONES experiment is the first to monitor changes in the basic biomechanical properties (tone, elasticity and stiffness) of the resting human myofascial system due to microgravity with a oninvasive, portable device on board the ISS. The MyotonPRO device applies several brief mechanical stimuli to the surface of the skin, and the natural oscillation signals of the tissue beneath are detected and computed by the MyotonPRO. Thus, an objective, quick and easy determination of the state of the underlying tissue is possible. Two preflight, four inflight and four post flight measurements were performed on a male astronaut using the same 10 measurement points (MP) for each session. MPs were located on the plantar fascia, Achilles tendon, M. soleus, M. gastrocnemius, M. multifidus, M. splenius capitis, M. deltoideus anterior, M. rectus femoris, infrapatellar tendon, M. tibialis anterior. Subcutaneous tissues thickness above the MPs was measured using ultrasound imaging. Magnetic resonance images (MRI) of lower limb muscles and functional tests were also performed pre- and postflight. Our first measurements on board the ISS confirmed increased tone and stiffness of the lumbar multifidus muscle, an important trunk stabilizer, dysfunction of which is known to be associated with back pain. Furthermore, reduced tone and stiffness of Achilles tendon and plantar fascia were observed inflight vs. preflight, confirming previous findings from terrestrial analog studies and parabolic flights. Unexpectedly, the deltoid showed negative inflight changes in tone and stiffness, and increased elasticity, suggesting a potential risk of muscle atrophy in longer spaceflight that should be addressed by adequate inflight countermeasure protocols. Most values from limb and back MPS showed deflected patterns (in either directions) from inflight shortly after the re-entry phase on the landing day and one week later. Most parameter values then normalized to baseline after 3 weeks likely due to 1G re-adaptation and possible outcome of the reconditioning protocol. No major changes in subcutaneous tissues thickness above the MPs were found inflight vs preflight, suggesting no bias (i.e., fluid shift, extreme tissue thickening or loss). Pre- and postflight MRI and functional tests showed negligible changes in calf muscle size, power and force, which is likely due to training effects from current inflight exercise protocols. The MYOTONES experiment is currently ongoing to collect data from further crew members. The potential impact of this research is to better understand the effects of microgravity and countermeasures over the time course of an ISS mission cycle. This will enable exercise countermeasures to be tailored Y1 - 2019 SN - 00741795 N1 - International Astronautical Congress: space: the power of the past, the promise of the future - Washington DC, USA/Vereinigte Staaten von Amerika Dauer: 21.10.2019 → 25.10.2019 PB - Pergamon CY - Oxford ER - TY - JOUR A1 - Bruksle, Ieva A1 - Chwallek, Constanze A1 - Krastina, Anzelika T1 - Strengthening sustainability in entrepreneurship education - implications for shifting entrepreneurial thinking towards sustainability at universities JF - ACTA PROSPERITATIS N2 - By developing innovative solutions to social and environmental problems, sustainable ventures carry greatpotential. Entrepreneurship which focuses especially on new venture creation can be developed through education anduniversities, in particular, are called upon to provide an impetus for social change. But social innovations are associatedwith certain hurdles, which are related to the multi-dimensionality, i.e. the tension between creating social,environmental and economic value and dealing with a multiplicity of stakeholders. The already complex field ofentrepreneurship education has to face these challenges. This paper, therefore, aims to identify starting points for theintegration of sustainability into entrepreneurship education. To pursue this goal experiences from three differentproject initiatives between the partner universities: Lapland University of Applied Sciences, FH Aachen University ofApplied Sciences and Turiba University are reflected and findings are systematically condensed into recommendationsfor education on sustainable entrepreneurship. KW - climate change KW - entrepreneurship education KW - Finland KW - Germany KW - Latvia Y1 - 2023 U6 - https://doi.org/10.37804/1691-6077-2023-14-37-48 SN - 1691-6077 VL - 14 IS - 1 SP - 37 EP - 48 PB - Sciendo ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Cronin, Neil J. A1 - Albracht, Kirsten A1 - Paulsen, Gøran A1 - Larsen, Askild V. A1 - Bojsen-Møller, Jens A1 - Seynnes, Olivier R. T1 - Training-induced increase in Achilles tendon stiffness affects tendon strain pattern during running JF - PeerJ N2 - Background During the stance phase of running, the elasticity of the Achilles tendon enables the utilisation of elastic energy and allows beneficial contractile conditions for the triceps surae muscles. However, the effect of changes in tendon mechanical properties induced by chronic loading is still poorly understood. We tested the hypothesis that a training-induced increase in Achilles tendon stiffness would result in reduced tendon strain during the stance phase of running, which would reduce fascicle strains in the triceps surae muscles, particularly in the mono-articular soleus. Methods Eleven subjects were assigned to a training group performing isometric singleleg plantarflexion contractions three times per week for ten weeks, and another ten subjects formed a control group. Before and after the training period, Achilles tendon stiffness was estimated, and muscle-tendon mechanics were assessed during running at preferred speed using ultrasonography, kinematics and kinetics. Results Achilles tendon stiffness increased by 18% (P <0:01) in the training group, but the associated reduction in strain seen during isometric contractions was not statistically significant. Tendon elongation during the stance phase of running was similar after training, but tendon recoil was reduced by 30% (P <0:01), while estimated tendon force remained unchanged. Neither gastrocnemius medialis nor soleus fascicle shortening during stance was affected by training. Discussion These results show that a training-induced increase in Achilles tendon stiffness altered tendon behaviour during running. Despite training-induced changes in tendon mechanical properties and recoil behaviour, the data suggest that fascicle shortening patterns were preserved for the running speed that we examined. The asymmetrical changes in tendon strain patterns supports the notion that simple inseries models do not fully explain the mechanical output of the muscle-tendon unit during a complex task like running. KW - Achilles tendon KW - Stiffness KW - Running KW - Tendon properties KW - Architectural gear ratio Y1 - 2019 U6 - https://doi.org/10.7717/peerj.6764 SN - 21678359 PB - Peer CY - London ER - TY - JOUR A1 - Ketelhut, Maike A1 - Göll, Fabian A1 - Braunstein, Björn A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Comparison of different training algorithms for the leg extension training with an industrial robot JF - Current Directions in Biomedical Engineering N2 - In the past, different training scenarios have been developed and implemented on robotic research platforms, but no systematic analysis and comparison have been done so far. This paper deals with the comparison of an isokinematic (motion with constant velocity) and an isotonic (motion against constant weight) training algorithm. Both algorithms are designed for a robotic research platform consisting of a 3D force plate and a high payload industrial robot, which allows leg extension training with arbitrary six-dimensional motion trajectories. In the isokinematic as well as the isotonic training algorithm, individual paths are defined i n C artesian s pace by sufficient s upport p oses. I n t he i sotonic t raining s cenario, the trajectory is adapted to the measured force as the robot should only move along the trajectory as long as the force applied by the user exceeds a minimum threshold. In the isotonic training scenario however, the robot’s acceleration is a function of the force applied by the user. To validate these findings, a simulative experiment with a simple linear trajectory is performed. For this purpose, the same force path is applied in both training scenarios. The results illustrate that the algorithms differ in the force dependent trajectory adaption. KW - Rehabilitation Technology and Prosthetics KW - Surgical Navigation and Robotics Y1 - 2018 U6 - https://doi.org/10.1515/cdbme-2018-0005 SN - 2364-5504 VL - 4 IS - 1 SP - 17 EP - 20 PB - De Gruyter CY - Berlin ER - TY - GEN T1 - Prüfungsordnung für die Masterstudiengänge „Information Systems Engineering“ und „Information Systems Engineering (Teilzeit)“ an der Fachhochschule Aachen : vom 5. November 2019 T3 - FH-Mitteilungen - 114/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Information Systems Engineering KW - Information Systems Engineering (Teilzeit) Y1 - 2019 ER - TY - GEN T1 - 2. Ordnung zur Änderung der Beitragsordnung der Studierendenschaft der Fachhochschule Aachen : vom 7. November 2019 T3 - FH-Mitteilungen - 115/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Beitragsordnung der Studierendenschaft Y1 - 2019 ER - TY - GEN T1 - Beitragsordnung der Studierendenschaft der Fachhochschule Aachen : vom 11. Dezember 2018 – FH-Mitteilung Nr. 168/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 7. November 2019 – FH-Mitteilung Nr. 115/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 116/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Beitragsordnung der Studierendenschaft Y1 - 2019 ER - TY - GEN T1 - Gesamtprüfungsordnung für den Bachelorstudiengang „Bauingenieurwesen mit Orientierungssemester“ an der Fachhochschule Aachen und der RWTH Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 117/2019 KW - Amtliche Mitteilung KW - Gesamtprüfungsordnung KW - Bachelor KW - Bauingenieurwesen mit Orientierungssemester KW - RWTH Aachen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für die Bachelorstudiengänge Bauingenieurwesen, Bauingenieurwesen mit Praxissemester, Bauingenieurwesen mit Auslandssemester, Bauingenieurwesen Double Degree (NUST) und Bauingenieurwesen Dual an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 118/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge Bauingenieurwesen, Bauingenieurwesen mit Praxissemester, Bauingenieurwesen mit Auslandssemester, Bauingenieurwesen Double Degree (NUST), Bauingenieurwesen Dual und Bauingenieurwesen mit Orientierungssemester im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 28. Juni 2018 – FH-Mitteilung Nr. 89/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 8. November 2019 – FH-Mitteilung Nr. 118/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 119/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für den Bachelorstudiengang Holzingenieurwesen im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 120/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge Holzingenieurwesen, Holzingenieurwesen mit Praxissemester, Holzingenieurwesen mit Auslandssemester, Holzingenieurwesen Dual und Holzingenieurwesen mit Orientierungssemester : vom 28. Juni 2018 – FH-Mitteilung Nr. 90/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 8. November 2019 – FH-Mitteilung Nr. 120/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 121/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Zugangsordnung für die Masterstudiengänge „Energiewirtschaft & Informatik“ (3 Semester) und „Energiewirtschaft & Informatik“ (4 Semester) Fachbereich Energietechnik Fachbereich Medizintechnik und Technomathematik an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 122/2019 KW - Amtliche Mitteilung KW - Zugangsordnung KW - Master KW - Energiewirtschaft KW - Informatik Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Masterstudiengänge „Energiewirtschaft & Informatik“ (3 Semester) und „Energiewirtschaft & Informatik“ (4 Semester) Fachbereich Energietechnik Fachbereich Medizintechnik und Technomathematik an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 123/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Energiewirtschaft KW - Informatik Y1 - 2019 ER - TY - JOUR A1 - Quittmann, Oliver J. A1 - Abel, Thomas A1 - Albracht, Kirsten A1 - Strüder, Heiko K. T1 - Biomechanics of all-out handcycling exercise: kinetics, kinematics and muscular activity of a 15-s sprint test in able-bodied participants JF - Sports Biomechanics N2 - This study aims to quantify the kinematics, kinetics and muscular activity of all-out handcycling exercise and examine their alterations during the course of a 15-s sprint test. Twelve able-bodied competitive triathletes performed a 15-s all-out sprint test in a recumbent racing handcycle that was attached to an ergometer. During the sprint test, tangential crank kinetics, 3D joint kinematics and muscular activity of 10 muscles of the upper extremity and trunk were examined using a power metre, motion capturing and surface electromyography (sEMG), respectively. Parameters were compared between revolution one (R1), revolution two (R2), the average of revolution 3 to 13 (R3) and the average of the remaining revolutions (R4). Shoulder abduction and internal-rotation increased, whereas maximal shoulder retroversion decreased during the sprint. Except for the wrist angles, angular velocity increased for every joint of the upper extremity. Several muscles demonstrated an increase in muscular activation, an earlier onset of muscular activation in crank cycle and an increased range of activation. During the course of a 15-s all-out sprint test in handcycling, the shoulder muscles and the muscles associated to the push phase demonstrate indications for short-duration fatigue. These findings are helpful to prevent injuries and improve performance in all-out handcycling. KW - Handbike KW - sEMG KW - Paralympic sport KW - performance testing KW - high-intensity exercise Y1 - 2022 U6 - https://doi.org/10.1080/14763141.2020.1745266 SN - 1752-6116 (Onlineausgabe) SN - 1476-3141 (Druckausgabe) VL - 21 IS - 10 SP - 1200 EP - 1223 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Richter, Charlotte A1 - Braunstein, Björn A1 - Stäudle, Benjamin A1 - Attias, Julia A1 - Süss, Alexander A1 - Weber, Tobias A1 - Mileva, Katya N. A1 - Rittweger, Jörn A1 - Green, David A. A1 - Albracht, Kirsten T1 - Gastrocnemius medialis contractile behavior during running differs between simulated Lunar and Martian gravities JF - Scientific reports N2 - The international partnership of space agencies has agreed to proceed forward to the Moon sustainably. Activities on the Lunar surface (0.16 g) will allow crewmembers to advance the exploration skills needed when expanding human presence to Mars (0.38 g). Whilst data from actual hypogravity activities are limited to the Apollo missions, simulation studies have indicated that ground reaction forces, mechanical work, muscle activation, and joint angles decrease with declining gravity level. However, these alterations in locomotion biomechanics do not necessarily scale to the gravity level, the reduction in gastrocnemius medialis activation even appears to level off around 0.2 g, while muscle activation pattern remains similar. Thus, it is difficult to predict whether gastrocnemius medialis contractile behavior during running on Moon will basically be the same as on Mars. Therefore, this study investigated lower limb joint kinematics and gastrocnemius medialis behavior during running at 1 g, simulated Martian gravity, and simulated Lunar gravity on the vertical treadmill facility. The results indicate that hypogravity-induced alterations in joint kinematics and contractile behavior still persist between simulated running on the Moon and Mars. This contrasts with the concept of a ceiling effect and should be carefully considered when evaluating exercise prescriptions and the transferability of locomotion practiced in Lunar gravity to Martian gravity. KW - Bone quality and biomechanics KW - Environmental impact KW - Skeletal muscle KW - Tendons KW - Ultrasound Y1 - 2021 U6 - https://doi.org/10.1038/s41598-021-00527-9 SN - 2045-2322 N1 - Corresponding author: Charlotte Richter VL - 11 IS - Article number: 22555 PB - Springer Nature CY - London ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Willwacher, Steffen A1 - Albracht, Kirsten T1 - Medial gastrocnemius muscle fascicles shorten throughout stance during sprint acceleration JF - Scandinavian Journal of Medicine & Science in Sports N2 - The compliant nature of distal limb muscle-tendon units is traditionally considered suboptimal in explosive movements when positive joint work is required. However, during accelerative running, ankle joint net mechanical work is positive. Therefore, this study aims to investigate how plantar flexor muscle-tendon behavior is modulated during fast accelerations. Eleven female sprinters performed maximum sprint accelerations from starting blocks, while gastrocnemius muscle fascicle lengths were estimated using ultrasonography. We combined motion analysis and ground reaction force measurements to assess lower limb joint kinematics and kinetics, and to estimate gastrocnemius muscle-tendon unit length during the first two acceleration steps. Outcome variables were resampled to the stance phase and averaged across three to five trials. Relevant scalars were extracted and analyzed using one-sample and two-sample t-tests, and vector trajectories were compared using statistical parametric mapping. We found that an uncoupling of muscle fascicle behavior from muscle-tendon unit behavior is effectively used to produce net positive mechanical work at the joint during maximum sprint acceleration. Muscle fascicles shortened throughout the first and second steps, while shortening occurred earlier during the first step, where negative joint work was lower compared with the second step. Elastic strain energy may be stored during dorsiflexion after touchdown since fascicles did not lengthen at the same time to dissipate energy. Thus, net positive work generation is accommodated by the reuse of elastic strain energy along with positive gastrocnemius fascicle work. Our results show a mechanism of how muscles with high in-series compliance can contribute to net positive joint work. KW - locomotion KW - muscle mechanics KW - running KW - sprint start KW - ultrasonography Y1 - 2021 U6 - https://doi.org/10.1111/sms.13956 SN - 0905-7188 (Druckausgabe) SN - 1600-0838 (Onlineausgabe) VL - 31 IS - 7 SP - 1471 EP - 1480 PB - Wiley-Blackwell CY - Oxford ER - TY - JOUR A1 - Monti, Elena A1 - Waldvogel, Janice A1 - Ritzmann, Ramona A1 - Freyler, Kathrin A1 - Albracht, Kirsten A1 - Helm, Michael A1 - De Cesare, Niccolò A1 - Pavan, Piero A1 - Reggiani, Carlo A1 - Gollhofer, Albert A1 - Narici, Marco Vincenzo T1 - Muscle in variable gravity: “I do not know where I am, but I know what to do” JF - Frontiers in Physiology N2 - Performing tasks, such as running and jumping, requires activation of the agonist and antagonist muscles before (motor unit pre-activation) and during movement performance (Santello and Mcdonagh, 1998). A well-timed and regulated muscle activation elicits a stretch-shortening cycle (SSC) response, naturally occurring in bouncing movements (Ishikawa and Komi, 2004; Taube et al., 2012). By definition, the SSC describes the stretching of a pre-activated muscle-tendon complex immediately followed by a muscle shortening in the concentric push-off phase (Komi, 1984). Given the importance of SSC actions for human movement, it is not surprising that many studies investigated the biomechanics of this phenomenon; in particular, drop jumps (DJs) represent a good paradigm to study muscle fascicle and tendon behavior in ballistic movements involving the SSC. Within a DJ, three main phases [pre-activation, braking, and push-off (PO; Komi, 2000)] have been recognized and extensively studied in common and challenging conditions, such as changes in load, falling height, or simulated hypo-gravity (Avela et al., 1994; Arampatzis et al., 2001; Fukashiro et al., 2005; Ishikawa et al., 2005; Sousa et al., 2007; Ritzmann et al., 2016; Helm et al., 2020). These studies show that the timing and amount of triceps-surae muscle-tendon unit pre-activation in DJs are differentially regulated based on the load applied to the muscle, being optimal in normal “Earth” gravity conditions (Avela et al., 1994), but decreased in simulated hypo-gravity, hyper-gravity (Avela et al., 1994; Ritzmann et al., 2016), or unknown conditions (i.e., unknown falling heights; Helm et al., 2020). Some authors indicated that, when falling from heights different from the optimal one [defined as the drop height giving a maximum DJ performance indicated as peak ground reaction force (GRF) or jump high], electromyographic (EMG) activity of the plantar flexors increases from lower than optimal to higher than optimal heights (Ishikawa and Komi, 2004; Sousa et al., 2007). These findings highlight the ability of the central nervous system to regulate the timing and amount of pre-activation according to different jumping conditions, thus regulating muscle fascicle length, tendon and joint stiffness as well as position, in order to safely land on the ground and quickly re-bounce. Similarly, to pre-activation, also in the braking phase, the plantar flexors are differentially regulated. In optimal height (i.e., load) jumping conditions, gastrocnemius medialis (GM) fascicles shorten at early ground contact (possibly due to the intervention of the stretch reflex; Gollhofer et al., 1992) and behave quasi-isometrically in the late braking phase, enabling tendon elongation, and storage of elastic energy (Gollhofer et al., 1992; Fukashiro et al., 2005; Sousa et al., 2007). When increasing the falling height (augmenting the impact GRF), the quasi-isometric behavior of fascicles disappears, and fast fascicle lengthening occurs (Ishikawa et al., 2005; Sousa et al., 2007). In the third and last PO phase, fascicles shorten and the tendon releases the elastic energy previously stored. Bobbert et al. (1987) reported no influence of jumping height on the work done and on the net vertical impulse assessed during PO; this observation suggests that, despite an optimal DJ performance might be achieved only in specific conditions (falling heights, loads), the central nervous system seems to be able to regulate muscle behavior in order to effectively perform the required task also in challenging situations. Although the regulation of triceps-surae muscle-tendon unit in DJs has been extensively investigated, very few studies focused on sarcomeres behavior during the performance of this SSC movement (Kurokawa et al., 2003; Fukashiro et al., 2005, 2006). Sarcomeres represent muscle contractile units and are known to express different amounts of force depending on their length (Gordon et al., 1966; Walker and Schrodt, 1974); thus, understanding the time course of their responses during DJs is fundamental to gain further insights into muscle force-generating capacity. In vivo measurement of sarcomere length in humans has been so far been performed only in static positions and under highly controlled experimental conditions (Llewellyn et al., 2008; Sanchez et al., 2015). Instead, human sarcomere length estimation (achieved by dividing GM measured fascicle length for a fixed sarcomere number) in dynamic contractions provided an indirect measure of sarcomere operating range during squat jump, countermovement jump, and DJ (Fukashiro et al., 2005, 2006; Kurokawa et al., 2003). The results of these studies showed that sarcomeres operate in the ascending limb of their length-tension (L-T) relationship in all types of jumps, and particularly so in DJ. However, most of the available observations on sarcomere and muscle fascicle behavior were made in condition of constant gravity. Thus, in order to understand how sarcomere and muscle fascicle length are regulated in variable gravity conditions, we performed experiments in a parabolic flight, involving variable gravity levels, ranging from about zero-g to about double the Earth’s gravity (1 g; Waldvogel et al., 2021). Specifically, the aims of the present study were as follows: 1. To investigate the ability of the neuromuscular system in regulating fascicle length in response to conditions of variable gravity. 2. To estimate sarcomere operative length in the different DJ phases, in order to calculate its theoretical force production and its possible modulation in conditions of variable gravity. We hypothesized that muscle fascicles would be differentially regulated in different gravity conditions compared to 1 g, particularly in anticipation of landing and re-bouncing in unknown gravity levels. In addition, we hypothesized that sarcomeres would operate in the upper part of the ascending limb of their L-T relationship, possibly lengthening during the braking phase (especially in hyper-gravity) while operating quasi-isometrically in 1 g. KW - parabolic flight KW - drop jump KW - hypo-gravity KW - hyper-gravity KW - sarcomere operating length Y1 - 2021 U6 - https://doi.org/10.3389/fphys.2021.714655 SN - 1664-042X VL - 12 PB - Frontiers Research Foundation CY - Lausanne ER - TY - CHAP A1 - Dreschers, Martin ED - Mönning, Rolf-Dieter T1 - §25 Arbeitsrechtliche Probleme im Rahmen der Betriebsfortführung T2 - Betriebsfortführung in Restrukturierung und Insolvenz Y1 - 2023 SN - 978-3-8145-2012-4 (print) SN - 978-3-8145-5888-2 (e-book) U6 - https://doi.org/https://doi.org/10.15375/9783814558882-028 SP - 947 EP - 988 PB - RWS Verlag CY - Köln ER - TY - CHAP A1 - Dreschers, Martin ED - Kübler, Bruno M. ED - Bork, Reinhard ED - Prütting, Hanns T1 - §18 Grenzüberschreitende Eigenverwaltung T2 - HRI II - Handbuch Restrukturierung in der Insolvenz Y1 - 2023 SN - 978-3-8145-2010-0 (print) SN - 978-3-8145-5871-4 (e-book) U6 - https://doi.org/10.15375/9783814558714-028 SP - 524 EP - 556 PB - RWS Verlag CY - Köln ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Albracht, Kirsten A1 - Cronin, Neil J A1 - Paulsen, Gøran A1 - Bojsen-Møller, Jens A1 - Seynnes, Olivier R T1 - Effect of training-induced changes in achilles tendon stiffness on muscle-tendon behavior during landing JF - Frontiers in physiology N2 - During rapid deceleration of the body, tendons buffer part of the elongation of the muscle-tendon unit (MTU), enabling safe energy dissipation via eccentric muscle contraction. Yet, the influence of changes in tendon stiffness within the physiological range upon these lengthening contractions is unknown. This study aimed to examine the effect of training-induced stiffening of the Achilles tendon on triceps surae muscle-tendon behavior during a landing task. Twenty-one male subjects were assigned to either a 10-week resistance-training program consisting of single-leg isometric plantarflexion (n = 11) or to a non-training control group (n = 10). Before and after the training period, plantarflexion force, peak Achilles tendon strain and stiffness were measured during isometric contractions, using a combination of dynamometry, ultrasound and kinematics data. Additionally, testing included a step-landing task, during which joint mechanics and lengths of gastrocnemius and soleus fascicles, Achilles tendon, and MTU were determined using synchronized ultrasound, kinematics and kinetics data collection. After training, plantarflexion strength and Achilles tendon stiffness increased (15 and 18%, respectively), and tendon strain during landing remained similar. Likewise, lengthening and negative work produced by the gastrocnemius MTU did not change detectably. However, in the training group, gastrocnemius fascicle length was offset (8%) to a longer length at touch down and, surprisingly, fascicle lengthening and velocity were reduced by 27 and 21%, respectively. These changes were not observed for soleus fascicles when accounting for variation in task execution between tests. These results indicate that a training-induced increase in tendon stiffness does not noticeably affect the buffering action of the tendon when the MTU is rapidly stretched. Reductions in gastrocnemius fascicle lengthening and lengthening velocity during landing occurred independently from tendon strain. Future studies are required to provide insight into the mechanisms underpinning these observations and their influence on energy dissipation. KW - achilles tendon KW - energy absorption KW - energy dissipation KW - mechanical buffer KW - stiffness Y1 - 2018 U6 - https://doi.org/10.3389/fphys.2018.00794 SN - 1664-042X IS - 9 PB - Frontiers Research Foundation CY - Lausanne ER - TY - GEN T1 - Richtlinie zur Durchführung von Sonderveranstaltungen in den Gebäuden und Liegenschaften der FH Aachen (Veranstaltungsrichtlinie) : vom 20. November 2019 T3 - FH-Mitteilungen - 124a/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - Veranstaltungsrichtlinie KW - Durchführung von Sonderveranstaltungen Y1 - 2019 ER - TY - GEN T1 - Richtlinie zur Durchführung von Sonderveranstaltungen in den Gebäuden und Liegenschaften der FH Aachen (Veranstaltungsrichtlinie) : vom 20. November 2019 Anlage 1 aktualisiert am 22. Januar 2020 T3 - FH-Mitteilungen - 124b/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - Veranstaltungsrichtlinie KW - Durchführung von Sonderveranstaltungen KW - Aktualisierung Y1 - 2019 ER - TY - GEN T1 - Richtlinie für die Beschäftigung und Vergütung studentischer und wissenschaftlicher Hilfskräfte an der Fachhochschule Aachen : vom 20. November 2019 T3 - FH-Mitteilungen - 125a/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - studentische Hilfskräfte KW - wissenschaftliche Hilfkräfte Y1 - 2019 ER - TY - GEN T1 - Richtlinie für die Beschäftigung und Vergütung studentischer und wissenschaftlicher Hilfskräfte an der Fachhochschule Aachen : vom 20. November 2019 aktualisiert am 24. November 2022 T3 - FH-Mitteilungen - 125b/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - studentische Hilfskräfte KW - wissenschaftliche Hilfkräfte Y1 - 2019 ER - TY - GEN T1 - Gleichstellungsquoten der FH Aachen für die Jahre 2019 –2021 : vom 20. November 2019 T3 - FH-Mitteilungen - 126/2019 KW - Amtliche Mitteilung KW - Gleichstellungsquoten KW - 2019 KW - 2020 KW - 2021 Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnungen für den Masterstudiengang „Nuclear Applications“ vom 13. Februar 2004 (FH-Mitteilung Nr. 5/2004) und vom 25. Februar 2010 (FH-Mitteilung Nr. 15/2010) in den Fassungen der Bekanntmachung der Änderungsordnungen vom 6. November 2012 (FH-Mitteilung Nr. 120/2012), 18. Juni 2014 (FH- Mitteilung Nr. 72/2014) und vom 15. Juni 2015 (FH-Mitteilung Nr. 28/2015) : vom 29. November 2019 T3 - FH-Mitteilungen - 127/2019 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Nuclear Applications Y1 - 2023 ER - TY - GEN T1 - 5. Ordnung zur Änderung der Prüfungsordnung für die Bachelorstudiengänge „Betriebswirtschaft Praxis Plus“ und „Betriebswirtschaft Praxis Plus (Teilzeit)“ mit dem Studienabschluss „Bachelor of Science“ am Fachbereich Wirtschaftswissenschaften der Fachhochschule Aachen (PO – BWL Praxis Plus) : vom 29. November 2019 T3 - FH-Mitteilungen - 128/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Betriebswirtschaft Praxis Plus Y1 - 2023 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge „Betriebswirtschaft Praxis Plus“ und „Betriebswirtschaft Praxis Plus (Teilzeit)“ mit dem Studienabschluss „Bachelor of Science“ am Fachbereich Wirtschaftswissenschaften der Fachhochschule Aachen (PO-BWL Praxis Plus) : vom 14. Januar 2014 – FH-Mitteilung Nr. 2/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 29. November 2019 – FH-Mitteilung Nr. 128/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2019/20) T3 - FH-Mitteilungen - 129/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Betriebswirtschaft Praxis Plus Y1 - 2023 ER - TY - GEN T1 - 2. Änderung der Richtlinie des Rektorats der FH Aachen für die Vergabe von Lehrveranstaltungsprämien : vom 13. Dezember 2019 T3 - FH-Mitteilungen - 130/2019 KW - Amtliche Mitteilung KW - Änderung KW - Richtlinie KW - Rektorat KW - Lehrveranstaltungsprämien Y1 - 2019 ER - TY - GEN T1 - Richtlinie des Rektorats der FH Aachen für die Vergabe von Lehrveranstaltungsprämien : vom 16. Juli 2012 – FH-Mitteilung Nr. 68/2012 in der Fassung der Bekanntmachung der Änderung vom 13. Dezember 2019 – FH-Mitteilung Nr. 130/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 131/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Richtlinie KW - Rektorat KW - Lehrveranstaltungsprämien Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den Masterstudiengang Nuclear Applications im Fachbereich Chemie und Biotechnologie an der Fachhochschule Aachen : vom 17. Dezember 2019 T3 - FH-Mitteilungen - 132/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Nuclear Applications KW - Chemie und Biotechnologie Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnung für den Masterstudiengang „Information Systems Engineering“ vom 22. Januar 2010 (FH-Mitteilung Nr. 5/2010), zuletzt geändert durch Änderungsordnung vom 4. Februar 2013 (FH-Mitteilung Nr. 6/2013) : vom 20. Dezember 2019 T3 - FH-Mitteilungen - 133/2019 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Information Systems Engineering Y1 - 2019 ER -