TY - JOUR A1 - Lopes, Pedro A1 - Leandro, Jorge A1 - Carvalho, Rita F. A1 - Bung, Daniel Bernhard T1 - Alternating skimming flow over a stepped spillway JF - Environmental Fluid Mechanics Y1 - 2017 U6 - https://doi.org/10.1007/s10652-016-9484-x SN - 1573-1510 VL - 17 IS - 2 SP - 303 EP - 322 PB - Springer CY - Berlin ER - TY - JOUR A1 - Valero, Daniel A1 - Bung, Daniel Bernhard A1 - Crookston, B.M. T1 - Energy dissipation of a Type III basin under design and adverse conditions for stepped and smooth spillways JF - Journal of Hydraulic Engineering N2 - New information regarding the influence of a stepped chute on the hydraulic performance of the United States Bureau of Reclamation (Reclamation) Type III hydraulic jump stilling basin is presented for design (steady) and adverse (decreasing tailwater) conditions. Using published experimental data and computational fluid dynamics (CFD) models, this paper presents a detailed comparison between smooth-chute and stepped-chute configurations for chute slopes of 0.8H:1V and 4H:1V and Froude numbers (F) ranging from 3.1 to 9.5 for a Type III basin designed for F = 8. For both stepped and smooth chutes, the relative role of each basin element was quantified, up to the most hydraulic extreme case of jump sweep-out. It was found that, relative to a smooth chute, the turbulence generated by a stepped chute causes a higher maximum velocity decay within the stilling basin, which represents an enhancement of the Type III basin’s performance but also a change in the relative role of the basin elements. Results provide insight into the ability of the CFD models [unsteady Reynolds-averaged Navier-Stokes (RANS) equations with renormalization group (RNG) k-ϵ turbulence model and volume-of-fluid (VOF) for free surface tracking] to predict the transient basin flow structure and velocity profiles. Type III basins can perform adequately with a stepped chute despite the effects steps have on the relative role of each basin element. It is concluded that the classic Type III basin design, based upon methodology by reclamation specific to smooth chutes, can be hydraulically improved for the case of stepped chutes for design and adverse flow conditions using the information presented herein. Y1 - 2018 U6 - https://doi.org/10.1061/(ASCE)HY.1943-7900.0001482 SN - 0733-9429 N1 - Article number 04018036 VL - 144 IS - 7 PB - ASCE CY - Reston, Va. ER - TY - JOUR A1 - Valero, Daniel A1 - Bung, Daniel Bernhard T1 - Vectrino profiler spatial filtering for shear flows based on the mean velocity gradient equation JF - Journal of Hydraulic Engineering N2 - A new methodology is proposed to spatially filter acoustic Doppler velocimetry data from a Vectrino profiler based on the differential mean velocity equation. Lower and upper bounds are formulated in terms of physically based flow constraints. Practical implementation is discussed, and its application is tested against data gathered from an open-channel flow over a stepped macroroughness surface. The method has proven to detect outliers occurring all over the distance range sampled by the Vectrino profiler and has shown to remain applicable out of the region of validity of the velocity gradient equation. Finally, a statistical analysis suggests that physically obtained bounds are asymptotically representative. Y1 - 2018 U6 - https://doi.org/10.1061/(ASCE)HY.1943-7900.0001485 SN - 0733-9429 N1 - Article number 04018037 VL - 144 IS - 7 PB - ASCE CY - Reston, Va. ER - TY - JOUR A1 - Krause, Thomas T1 - Bauabrechnung und Mengenermittlung JF - Zahlentafeln für den Baubetrieb / Hoffmann, Manfred ; Kuhlmann, Willy [Hrsg.]. 7., vollst. überarb. Aufl. Y1 - 2006 SN - 3-519-65220-X N1 - Kapitel 7 SP - 491 EP - 546 PB - Teubner CY - Wiesbaden ER - TY - JOUR A1 - Krause, Thomas A1 - Kremer, Norbert T1 - Schalung und Gerüste JF - Zahlentafeln für den Baubetrieb / Hoffmann, Manfred ; Kuhlmann, Willy [Hrsg.]. 7., vollst. überarb. Aufl. Y1 - 2006 SN - 3-519-65220-X N1 - Kapitel 11 SP - 709 EP - 747 PB - Teubner CY - Wiesbaden ER - TY - JOUR A1 - Lohse, Wolfram T1 - Stahlbau JF - Wendehorst Beispiele aus der Baupraxis / Wetzell, Otto W. ; Baumgartner, Herwig ; Wendehorst, Reinhard [Hrsg.]. Y1 - 2007 SN - 978-3-8351-0069-5 N1 - Kapitel 6 SP - 129 EP - 167 PB - Teubner CY - Wiesbaden ER - TY - JOUR A1 - Lohse, Wolfram T1 - Stahlbau JF - Bautechnische Zahlentafeln : [jetzt mit neuer DIN 1052, DIN1053-1 und DIN 1054] / Wendehorst. Hrsg. von Otto W. Wetzell. Bearb. von: Herwig Baumgartner ... 31., vollst. überb. und aktualisierte Aufl. Y1 - 2004 SN - 3-519-55002-4 N1 - Abschnitt 9 SP - 603 EP - 738 PB - Teubner [u.a.] CY - Stuttgart [u.a.] ER - TY - JOUR A1 - Krause, Thomas T1 - Bauabrechnung und Mengenermittlung JF - Beispiele für die Baubetriebspraxis / Hoffmann, Manfred ; Kuhlmann, Willy [Hrsg.]. Y1 - 2006 SN - 978-3-8351-0002-2 N1 - Kapitel 4 SP - 49 EP - 62 PB - Teubner CY - Wiesbaden ER - TY - JOUR A1 - Lohse, Wolfram T1 - Integraltafel für konische Stäbe mit doppelsymmetrischem I-Querschnitt JF - Stahlbau. 68 (1999), H. 2 Y1 - 1999 SN - 0038-9145 SP - 91 EP - 95 ER - TY - JOUR A1 - Valero, Daniel A1 - Bung, Daniel Bernhard T1 - Sensitivity of turbulent Schmidt number and turbulence model to simulations of jets in crossflow JF - Environmental Modelling and Software N2 - Environmental discharges have been traditionally designed by means of cost-intensive and time-consuming experimental studies. Some extensively validated models based on an integral approach have been often employed for water quality problems, as recommended by USEPA (i.e.: CORMIX). In this study, FLOW-3D is employed for a full 3D RANS modelling of two turbulent jet-to-crossflow cases, including free surface jet impingement. Results are compared to both physical modelling and CORMIX to better assess model performance. Turbulence measurements have been collected for a better understanding of turbulent diffusion's parameter sensitivity. Although both studied models are generally able to reproduce jet trajectory, jet separation downstream of the impingement has been reproduced only by RANS modelling. Additionally, concentrations are better reproduced by FLOW-3D when the proper turbulent Schmidt number is used. This study provides a recommendation on the selection of the turbulence model and the turbulent Schmidt number for future outfall structures design studies. Y1 - 2016 U6 - https://doi.org/10.1016/j.envsoft.2016.04.030 SN - 1364-8152 (electronic) VL - 82 SP - 218 EP - 228 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Egner, Ralf A1 - Heyde, Stefan A1 - Laumann, Jörg A1 - Prokop, Ines T1 - Vorschläge für eine anwenderfreundliche und praxistaugliche Novellierung der allgemeinen Bemessungsregeln und Regeln für den Hochbau (EN 1993 Teil 1-1) JF - Stahlbau Y1 - 2015 U6 - https://doi.org/10.1002/stab.201510321 SN - 1437-1049 VL - 84 IS - 10 SP - 811 EP - 822 PB - Ernst & Sohn CY - Berlin ER - TY - JOUR A1 - Lohse, Wolfram T1 - Stahlbau JF - Bautechnische Zahlentafeln / Wendehorst, Reinhard ; Wetzell, Otto W. [Hrsg.] 32., vollst. aktualisierte Aufl. Y1 - 2007 SN - 978-3-8351-0055-8 SP - 607 EP - 757 PB - Teubner CY - Stuttgart ER - TY - JOUR A1 - Lohse, Wolfram T1 - Kippnachweise nach DIN 4114 und Entwurf DIN 18800 Teil 2 - ein Hinweis für die Praxis JF - Schweissen und Schneiden : Fachzeitschrift für Schweißen und verwandte Verfahren / Hrsg.: DVS - Deutscher Verband für Schweißen und Verwandte Verfahren e.V.. 41 (1989), H. 9 Y1 - 1989 SN - 0036-7184 SP - 459 EP - 462 ER - TY - JOUR A1 - Reger, Vitali A1 - Kuhnhenne, Markus A1 - Hachul, Helmut A1 - Döring, Bernd A1 - Blanke, Tobias A1 - Göttsche, Joachim T1 - Plusenergiegebäude 2.0 in Stahlleichtbauweise JF - Stahlbau Y1 - 2019 U6 - https://doi.org/10.1002/stab.201900034 SN - 1437-1049 (E-journal), 0038-9145 (print) VL - 88 IS - 6 SP - 522 EP - 528 PB - Ernst & Sohn CY - Berlin ER - TY - JOUR A1 - Peterson-Oster, Madeleine A1 - Peterson, Leif Arne T1 - Gewerbebau: Modellprojekt mit neuem elementiertem, freistehendem Fassadensystem JF - Bauen mit Holz, Der Zimmermann N2 - Die im Zuge einer Betriebsübergabe anstehende Baumaßnahmen am eigenen Büro- und Produktionsgebäude boten ideale Voraussetzung zur Anwendung einer raum­-kreierenden Außenhaut. Mit der elementierten, freistehenden Eichenholz-Fassade wurde ein bis dahin weitgehend funktionales Bauwerk substanzschonend und zugleich optisch ansprechender umgestaltet. Y1 - 2020 SN - 0005-6545 PB - Rudolf Müller CY - Köln ER - TY - JOUR A1 - Peterson-Oster, Madeleine A1 - Peterson, Leif Arne T1 - Fassadensystem: Optisch ansprechend, freistehend, elementiert und aus Eichenholz JF - Bauen mit Holz, Der Zimmermann N2 - Bei der Entwicklung des Fassadensystems ging es darum die mögliche Dauerhaftigkeit von Holz bei direkter Bewitterung zu maximieren. Gleichzeitig soll gezeigt werden, dass mittels durchdachter Ansätze beim konstruktiven Holzschutz und die Wahl einer geeigneten Holzart langlebige Konstruktionen realisiert werden können. Y1 - 2020 SN - 0005-6545 PB - Rudolf Müller CY - Köln ER - TY - JOUR A1 - Laumann, Jörg A1 - Mainz, Stefan T1 - Direkte Ermittlung der erforderlichen Einspanntiefe von I‑förmigen Stahlquerschnitten in Betonkonstruktionen N2 - Für die Ermittlung der erforderlichen Einspanntiefe von eingespannten Stahlquerschnitten in Betonkonstruktionen existieren verschiedene Bemessungsmodelle. Diese basieren vorwiegend auf Grundlage nationaler Normen wie z. B. DIN 18800 [1] und DIN 1045 [2], die durch die europäische Normung ersetzt wurden. Aus diesem Grund wird in diesem Aufsatz ein Berechnungsmodell für die erforderliche Einspanntiefe von eingespannten Stahlquerschnitten in Betonkonstruktionen auf Grundlage des Eurocodes vorgestellt. Das Grundgerüst für dieses Berechnungsmodell bildet das Verfahren nach Kindmann und Laumann, welches in [3] behandelt wurde. Gleichzeitig werden neue Formeln zur direkten Ermittlung der Mindesteinspanntiefe vorgestellt. Behandelt werden gewalzte I-Profile für einachsige Biegung um die starke Achse (y-y) mit Drucknormalkraft. Y1 - 2012 U6 - https://doi.org/10.1002/stab.201201620 SN - 1437-1049 VL - 81 IS - 11 SP - 850 EP - 860 PB - Wiley CY - Weinheim ER -