TY  - JOUR
A1  - Coll-Perales, Baldomero
A1  - Schulte-Tigges, Joschua
A1  - Rondinone, Michele
A1  - Gozalvez, Javier
A1  - Reke, Michael
A1  - Matheis, Dominik
A1  - Walter, Thomas
T1  - Prototyping and evaluation of infrastructure-assisted transition of control for cooperative automated vehicles
JF  - IEEE Transactions on Intelligent Transportation Systems
N2  - Automated driving is now possible in diverse road and traffic conditions. However, there are still situations that automated vehicles cannot handle safely and efficiently. In this case, a Transition of Control (ToC) is necessary so that the driver takes control of the driving. Executing a ToC requires the driver to get full situation awareness of the driving environment. If the driver fails to get back the control in a limited time, a Minimum Risk Maneuver (MRM) is executed to bring the vehicle into a safe state (e.g., decelerating to full stop). The execution of ToCs requires some time and can cause traffic disruption and safety risks that increase if several vehicles execute ToCs/MRMs at similar times and in the same area. This study proposes to use novel C-ITS traffic management measures where the infrastructure exploits V2X communications to assist Connected and Automated Vehicles (CAVs) in the execution of ToCs. The infrastructure can suggest a spatial distribution of ToCs, and inform vehicles of the locations where they could execute a safe stop in case of MRM. This paper reports the first field operational tests that validate the feasibility and quantify the benefits of the proposed infrastructure-assisted ToC and MRM management. The paper also presents the CAV and roadside infrastructure prototypes implemented and used in the trials. The conducted field trials demonstrate that infrastructure-assisted traffic management solutions can reduce safety risks and traffic disruptions.
KW  - Automated driving
KW  - automated vehicles
KW  - connected automated vehicles
KW  - CAV
KW  - experimental evaluation
Y1  - 2021
U6  - https://doi.org/10.1109/TITS.2021.3061085
SN  - 1524-9050 (Print)
SN  - 1558-0016 (Online)
VL  - 23
IS  - 7
SP  - 6720
EP  - 6736
PB  - IEEE
ER  - 
TY  - JOUR
A1  - Pietsch, Wolfram
A1  - Kurbel, K.
A1  - Labentz, M.
T1  - Prototyping und Projektmanagement bei großen Entwicklungsteams / Kurbel, K., Labentz, M., Pietsch, W.
JF  - Information management : IM ; Praxis, Ausbildung u. Forschung d. Wirtschaftsinformatik. 2 (1987), H. 1
Y1  - 1987
SN  - 0930-5181
SP  - 6
EP  - 15
ER  - 
TY  - JOUR
A1  - Niemüller, Tim
A1  - Ferrein, Alexander
A1  - Eckel, Gerhard
A1  - Pirro, David
A1  - Podbregar, Patrick
A1  - Kellner, Tobias
A1  - Rath, Christoph
A1  - Steinbauer, Gerald
T1  - Providing Ground-truth Data for the Nao Robot Platform
JF  - RoboCup 2010: Robot Soccer World Cup XIV
Y1  - 2011
SN  - 978-3-642-20217-9
N1  - Lecture Notes in Computer Science ; 6556
SP  - 133
EP  - 144
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Hackl, Michael
A1  - Müller, Lars-Peter
A1  - Staat, Manfred
A1  - Kahmann, Stephanie Lucina
A1  - Wegmann, Kilian
T1  - Proximal phalangeal neck fractures of the hand — a biomechanical comparison of three fixation techniques
JF  - Knee surgery, sports traumatology, arthroscopy
N2  - Plate osteosynthesis of displaced proximal phalangeal neck fractures of the hand allows early mobilization due to a stable internal fixation. Nevertheless, joint stiffness—because of soft tissue irritation—represents a common complication leading to high complication rates. Del Pinal et al. recently reported promising clinical results for a new, minimally invasive fixation technique with a cannulated headless intramedullary compression screw. Hence, the aim of this study was to compare plate fixation of proximal phalangeal neck fractures to less two less invasive techniques: Crossed k-wire fixation and intramedullary screw fixation. We hypothesized that these fixation techniques provide inferior stability when compared to plate osteosynthesis.
Y1  - 2016
U6  - https://doi.org/10.1007/s00167-016-4080-7
SN  - 0942-2056
VL  - Volume 24
IS  - Supplement 1
SP  - 148
EP  - 149
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Schmitz, M.
A1  - Hirsch, E.
A1  - Bongaerts, Johannes
A1  - Takors, Ralf
T1  - Pulse experiments as a prerequisite for the quantification of in vivo enzyme kinetics in aromatic amino acid pathway of Eschericia coli
JF  - Biotechnology progress
Y1  - 2002
SN  - 1520-6033 (E-Journal); 8756-7938 (Print)
VL  - Vol. 18
IS  - Iss. 5
SP  - 935
EP  - 941
ER  - 
TY  - JOUR
A1  - Streun, M.
A1  - Brandenburg, G.
A1  - Larue, H.
A1  - Zimmermann, E.
A1  - Ziemons, Karl
A1  - Halling, H.
T1  - Pulse recording by free-running sampling
JF  - IEEE Transactions on Nuclear Science
N2  - Pulses from a position-sensitive photomultiplier (PS-PMT) are recorded by free-running ADCs at a sampling rate of 40 MHz. A four-channel acquisition board has been developed which is equipped with four 12-bit ADCs connected to one field programmable gate array (FPGA). The FPGA manages data acquisition and the transfer to the host computer. It can also work as a digital trigger, so a separate hardware trigger can be omitted. The method of free-running sampling provides a maximum of information, besides the pulse charge and amplitude also pulse shape and starting time are contained in the sampled data. This information is crucial for many tasks such as distinguishing between different scintillator materials, determination of radiation type, pile-up recovery, coincidence detection or time-of-flight applications. The absence of an analog integrator allows very high count rates to be dealt with. Since this method is to be employed in positron emission tomography (PET), the position of an event is also important. The simultaneous readout of four channels allows localization by means of center-of-gravity weighting. First results from a test setup with LSO scintillators coupled to the PS-PMT are presented here
Y1  - 2001
SN  - 0018-9499
VL  - 48
IS  - 3
SP  - 524
EP  - 526
ER  - 
TY  - JOUR
A1  - Streun, M.
A1  - Brandenburg, G.
A1  - Larue, H.
A1  - Zimmermann, E.
A1  - Ziemons, Karl
A1  - Halling, H.
T1  - Pulse recording by free-running sampling
JF  - 2000 IEEE Nuclear Science Symposium Conference Record, Vol. 2
N2  - Pulses from a position-sensitive photomultiplier (PS-PMT) are recorded by free running ADCs at a sampling rate of 40 MHz. A four-channel acquisition-board has been developed which is equipped with four 12 bit-ADCs connected to one FPGA (field programmable gate array). The FPGA manages data acquisition and the transfer to the host computer. It can also work as a digital trigger, so a separate hardware-trigger can be omitted. The method of free running sampling provides a maximum of information, besides the pulse charge and amplitude also pulse shape and starting time are contained in the sampled data. These informations are crucial for many tasks such as distinguishing between different scintillator materials, determination of radiation type, pile-up recovery, coincidence detection or time-of-flight applications. The absence of an analog integrator allows coping with very high count rates. Since this method is going to be employed in positron emission tomography (PET), the position of an event is another important information. The simultaneous readout of four channels allows localization by means of center-of-gravity weighting. First results from a test setup with LSO-scintillators coupled to the PS-PMT are presented
Y1  - 2000
SN  - 1082-3654
SP  - 9/179
EP  - 9/181
ER  - 
TY  - JOUR
A1  - Streun, M.
A1  - Brandenburg, G.
A1  - Larue, H.
A1  - Saleh, H.
A1  - Zimmermann, E.
A1  - Ziemons, Karl
A1  - Halling, H.
T1  - Pulse shape discrimination of LSO and LuYAP scintillators for depth of interaction detection in PET
JF  - 2002 IEEE Nuclear Science Symposium Conference Record, Vol. 3
N2  - A feasible way to gain the depth of interaction information in a PET scanner is the use of phoswich detectors. In general the layer of interaction is identified front the pulse shape of the corresponding scintillator material. In this work pulses from LSO and LuYAP crystals were investigated in order to find a practical method of distinguishing. It turned out that such a pulse processing could he kept simple due to an additional slow component in the light decay of the LuYAP pulse. At the same time the short decay time guarantees that the major amount of the light output is still collected within a short pulse recording time.
Y1  - 2003
SN  - 1082-3654
SP  - 1636
EP  - 1639
ER  - 
TY  - JOUR
A1  - Streun, M.
A1  - Brandenburg, G.
A1  - Larue, H.
A1  - Saleh, H.
A1  - Zimmermann, E.
A1  - Ziemons, Karl
A1  - Halling, H.
T1  - Pulse shape discrimination of LSO and LuYAP scintillators for depth of interaction detection in PET
JF  - IEEE Transactions on Nuclear Science
N2  - A feasible way to gain the depth of interaction information in a positron emission tomography scanner is the use of phoswich detectors. In general, the layer of interaction is identified from the pulse shape of the corresponding scintillator material. In this work, pulses from LSO and LuYAP crystals were investigated in order to find a practical method of distinguishing. It turned out that such a pulse processing could be kept simple because of an additional slow component in the light decay of the LuYAP pulse. At the same time, the short decay time guarantees that the major amount of the light output is still collected within a short pulse recording time.
Y1  - 2003
SN  - 0018-9499
VL  - 50
IS  - 3
SP  - 344
EP  - 347
ER  - 
TY  - JOUR
A1  - Kotliar, Konstantin
A1  - Baumann, Marcus
A1  - Vilser, Walthard
A1  - Lanzl, Ines M.
T1  - Pulse wave velocity in retinal arteries of healthy volunteers
JF  - British Journal of Ophthalmology (eBJO)
Y1  - 2011
SN  - 1468-2079
VL  - 95
IS  - 11
SP  - 675
EP  - 679
PB  - BMJ Publ. Group
CY  - London
ER  - 
TY  - JOUR
A1  - Schöning, Michael Josef
A1  - Schubert, Jürgen
A1  - Zander, Willy
A1  - Müller-Veggian, Mattea
T1  - Pulsed laser deposition as a novel preparation technique for chemical microsensors
JF  - Proceedings of SPIE 3857, Chemical Microsenors and Applications II, 124 (November 18, 1999). 3857 (1999)
Y1  - 1999
SP  - 124
EP  - 134
ER  - 
TY  - JOUR
A1  - Schöning, Michael Josef
A1  - Schaub, A.
A1  - Zundel, A.
A1  - Beckers, L.
A1  - Schubert, J.
A1  - Zander, W.
A1  - Kordos, P.
A1  - Lüth, H.
T1  - Pulsed laser deposition as a novel thin film preparation method for silicon-based field effect sensors
JF  - Proceedings of the 25th European Solid State Device Research Conference : the Netherlands Congress Centre, The Hague, the Netherlands, 25th - 27th September 1995 / ESSDERC '95. Ed. by H. C. de Graaff
Y1  - 1995
SN  - 2-86332-182-X
N1  - ESSDERC ; (25, 1995, 's-Gravenhage) ; European Solid State Device Research Conference (ESSDERC) ; (25 : ; 1995.09.25-27 : ; Den Haag)
SP  - 601
EP  - 604
PB  - Ed. Frontières
CY  - Gif-sur-Yvette
ER  - 
TY  - JOUR
A1  - Schöning, Michael Josef
A1  - Mourzina, Yu.G.
A1  - Schubert, J.
A1  - Zander, W.
A1  - Legin, A.
A1  - Vlasov, Y. G.
A1  - Lüth, H.
T1  - Pulsed laser deposition – an innovative technique for preparing inorganic thin films
JF  - Electroanalysis. 13 (2001), H. 8-9
Y1  - 2001
SN  - 1040-0397
SP  - 727
EP  - 732
ER  - 
TY  - JOUR
A1  - Kloock, Joachim P.
A1  - Mourzina, Y.
A1  - Schubert, J.
A1  - Ermelenko, Y.
A1  - Schöning, Michael Josef
T1  - Pulsed laser deposition: A tool for fabricating thin-film microsensors
JF  - Biomedizinische Technik. 49 (2004), H. 2
Y1  - 2004
SN  - 0932-4666
SP  - 1032
EP  - 1033
ER  - 
TY  - JOUR
A1  - Biselli, Manfred
A1  - Thömmes, J.
A1  - Born, C.
A1  - Wandrey, C.
T1  - Purification of monoclonal antibodies by fluidized bed adsorption / Thömmes, J. ; Born, C.  Biselli, M. ; Wandrey, C. ; Kula, M.-R.
JF  - Animal cell technology : developments towards the 21st century / edited by E. C. Beuvery
Y1  - 1995
SN  - 0-7923-3736-0
N1  - Meeting "Animal Cell Technology, Developments towards the 21st Century" ; <1994.09.12-16 : ; Veldhoven>
SP  - 515
EP  - 519
PB  - Kluwer Acad. Press
CY  - Dordrecht
ER  - 
TY  - JOUR
A1  - Tippkötter, Nils
A1  - Roth, Jasmine
T1  - Purified Butanol from Lignocellulose – Solvent‐Impregnated Resins for an Integrated Selective Removal
JF  - Chemie Ingenieur Technik
N2  - In traditional microbial biobutanol production, the solvent must be recovered during fermentation process for a sufficient space-time yield. Thermal separation is not feasible due to the boiling point of n-butanol. As an integrated and selective solid-liquid separation alternative, solvent impregnated resins (SIRs) were applied. Two polymeric resins were evaluated and an extractant screening was conducted. Vacuum application with vapor collection in fixed-bed column as bioreactor bypass was successfully implemented as butanol desorption step. In course of further increasing process economics, fermentation with renewable lignocellulosic substrates was conducted using Clostridium acetobutylicum. Utilization of SIR was shown to be a potential strategy for solvent removal from fermentation broth, while application of a bypass column allows for product removal and recovery at once.
KW  - Biofuel
KW  - Biorefinery
KW  - Butanol
KW  - Clostridium acetobutylicum
KW  - Lignocellulose
Y1  - 2020
U6  - https://doi.org/10.1002/cite.202000200
SN  - 1522-2640
N1  - Corresponding author: Nils Tippkötter
VL  - 92
IS  - 11
SP  - 1741
EP  - 1751
PB  - Wiley-VCH
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Pietsch, Wolfram
A1  - Herzwurm, G.
T1  - QFD for Customer-Focused Requirements Engineering / Herzwurm, G., Pietsch, W.
JF  - Proceedings : 8 - 12 September 2003, Monterey Bay, California, USA / sponsored by IEEE Computer Society Technical Council on Software Engineering (TCSE) ... In cooperation with ACM SigSOFT
Y1  - 2003
SN  - 0769519806
N1  - International Requirements Engineering Conference ; (11, 2003, Monterey, Calif.)
SP  - 330
EP  - 338
PB  - IEEE Computer Society
CY  - Los Alamitos, Calif. [u.a.]
ER  - 
TY  - JOUR
A1  - Höttges, Jörg
T1  - QKan - Management of drainage system data with QGIS
JF  - Free and Open Source Software for Geospatial (FOSS4G) Conference Proceedings
Y1  - 2017
VL  - 17
IS  - Article 13
SP  - 95
EP  - 100
ER  - 
TY  - JOUR
A1  - Schuba, Marko
A1  - Schneider, Gaby
A1  - Haverkort, Boudewijn R.
T1  - QNA-MC: A Performance Evaluation Tool for Communication Networks with Multicast Data Streams / Schneider, G. ; Schuba, M. ; Haverkort, B. R.
JF  - Computer Performance Evaluation - Modelling Techniques and Tools / Puigjaner, Ramon (eds.)
Y1  - 1998
SN  - 3-540-64949-2
N1  - Lecture notes in computer  science ; 1469
SP  - 105
EP  - 116
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Raffeis, Iris
A1  - Adjei-Kyeremeh, Frank
A1  - Vroomen, Uwe
A1  - Westhoff, Elmar
A1  - Bremen, Sebastian
A1  - Hohoi, Alexandru
A1  - Bührig-Polaczek, Andreas
T1  - Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties
JF  - Applied Sciences
N2  - As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni–Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s–1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20% to 31% (V), as well as from 16% to 25% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced.
Y1  - 2020
U6  - https://doi.org/10.3390/app10103401
SN  - 2076-3417
N1  - Special Issue Materials Development by Additive Manufacturing Techniques
VL  - 10
IS  - Art. 3401
SP  - 1
EP  - 15
PB  - MDPI
CY  - Basel
ER  -