TY - JOUR A1 - Meliß, Michael A1 - Oesterwind, Dieter A1 - Voß, Alfred T1 - Non-nuclear and non-fossil energy resources and their possibilities for future power generation JF - Kerntechnik N2 - It must be stressed that the assessment of the exploitation possibilities of the energy resources discussed in this paper requires further studies. With this proviso, the situation can be provisionally summarised as follows: The total potential of known geothermal steam sources is only 64 GW. Geothermal energy could therefore only make a significant contribution to covering the worldwide power needs if we succeed in exploiting dry geothermal reservoirs. Exploitation of tidal energy is limited to a few geographically favourable locations. The power generation potential at these locations is only about 64 GW. An important drawback of tidal power is discontinuous power generation. Large scale exploitation of wind, wave and glacier energy, and of ocean heat, requires solution of a number of technological problems. The environmental effects of exploitation of these energy resources are to some extent of a qualitatively different nature from those of operation of fossil-fuel-fired and of nuclear power plants. The scanty knowledge in this area often results in these effects being underestimated. In any case, however, it would be deliberately misleading to postulate that any form of power generation is possible without some detrimental effects on the environment. It may be stated in conclusion that, owing to their small potential or to the as yet insufficiently advanced technological development, none of the energy resources discussed in this paper can make a significant contribution to the solution of middle-term energy supply problems, i.e., to a rapid replacement of mineral oil and natural gas. Y1 - 1975 U6 - http://dx.doi.org/10.18419/opus-8093 SN - 0932-3902 N1 - Printausg. in der Bibliothek vorhanden: 63 ZS 010-1975 VL - 17 IS - 7 SP - 301 EP - 306 PB - De Gruyter CY - Berlin ER - TY - JOUR A1 - Kern, Alexander A1 - Braun, Christian T1 - Neuerungen bei der Blitzschutznorm. Teil 2 JF - etz Elektrotechnik und Automation Y1 - 2013 SN - 0170-1711 N1 - Printausg. in der Bibliothek der FH Aachen vorhanden: 23 Z 133 ; 63 ZS 035 VL - Bd. 134 IS - H. 8 SP - 66 EP - 69 PB - VDE-Verlag CY - Wuppertal ER - TY - JOUR A1 - Hellmanns, Mark A1 - Böhm, Stefan A1 - Dilger, Klaus T1 - Manual applications of adhesives JF - Journal of adhesion and interface Y1 - 2006 VL - Vol. 7 IS - No. 4 SP - 24 EP - 27 ER - TY - JOUR A1 - Böhm, Stefan A1 - Hellmanns, Mark A1 - Backes, Andreas A1 - Dilger, Klaus T1 - Lock-in thermography based NDT of parts for the automotive industry JF - Journal of adhesion and interface Y1 - 2006 VL - Vol. 7 IS - No. 4 SP - 10 EP - 12 ER - TY - JOUR A1 - Sabitova, A. A1 - Ebert, Ph. A1 - Lenz, A. A1 - Schaafhausen, S. A1 - Ivanova, L. A1 - Dähne, M. A1 - Hoffmann, A. A1 - Dunin-Borkowski, R. E. A1 - Förster, Arnold A1 - Grandidier, B. A1 - Eisele, H. T1 - Intrinsic bandgap of cleaved ZnO(112¯0) surfaces JF - Applied physics letters Y1 - 2013 SN - 1077-3118 (E-Journal); 0003-6951 (Print) VL - Vol. 102 SP - 021608 ER - TY - JOUR A1 - Kirschkamp, T. A1 - Jöckel, M. A1 - Wählisch, Georg A1 - Barry, J. C. T1 - Konstruktion eines Modellauges zur Simulation von Purkinje-Spiegelbildern für die Bestimmung der Krümmungsradien und der Lage der Augenlinse JF - Biomedizinische Technik = Biomedical Engineering Y1 - 1998 SN - 1862-278X (E-Journal); 0013-5585 (Print) N1 - Printausg. in der Bibliothek vorhanden: 63 Z 471-1998/99 VL - Bd. 43 IS - H. 11 SP - 318 EP - 325 ER - TY - JOUR A1 - Pauksztat, Anja A1 - Kuperjans, Isabel A1 - Meyer, Jörg T1 - Formeln statt Zahlen : Referenzwerte Formeln zur energetischen Bewertung von Produktionsanlagen JF - BWK : das Energie-Fachmagazin Y1 - 2005 SN - 0006-9612 SN - 1618-193X VL - 57 IS - 12 SP - 52 EP - 55 ER - TY - JOUR A1 - Kuperjans, Isabel A1 - Gürzenich, D. A1 - Roosen, P. T1 - Kostenfunktionen im WWW : Unterstützung der Auslegung energietechnischer Anlagen und deren Verschaltungen JF - Gaswärme international (GWI) Y1 - 2005 SN - 0020-9384 VL - 54 IS - 1 SP - 19 EP - 21 ER - TY - JOUR A1 - Kuperjans, Isabel T1 - Exergetische und exergoökonomische Analyse thermischer Prozesse JF - Arbeitsbericht / Institut für Wirtschaftswissenschaften, Rheinisch-Westfälische Technische Hochschule Aachen Y1 - 1996 IS - 06 ER - TY - JOUR A1 - Alebouyeh Samami, Behzad A1 - Pieper, Martin A1 - Breitbach, Gerd A1 - Hodapp, Josef T1 - Heat production in the windings of the stators of electric machines under stationary condition JF - Heat and mass transfer N2 - In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results. Y1 - 2014 U6 - http://dx.doi.org/10.1007/s00231-014-1371-8 SN - 0947-7411 (Print) ; 1432-1181 (E-Journal) VL - 50 SP - 1707 EP - 1716 PB - Springer CY - Heidelberg ER - TY - JOUR A1 - Pauksztat, Anja A1 - Kuperjans, Isabel A1 - Meyer, Jörg T1 - Produktbezogene Referenzwerte für Energieeffizienz und CO2-Emissionen JF - Energiewirtschaftliche Tagesfragen : et ; Zeitschrift für Energiewirtschaft, Recht, Technik und Umwelt Y1 - 2005 SN - 0013-743X SN - 0720-6240 VL - 55 IS - 6 SP - 374 EP - 376 ER - TY - JOUR A1 - Kuperjans, Isabel A1 - Starke, M. A1 - Esser, J. A1 - [u.a.], T1 - Analyse und Konzeption von Energieanlagen unter ökologischen, wirtschaftlichen und technischen Gesichtspunkten JF - WLB : Umwelttechnik für Industrie und Kommune Y1 - 2000 SN - 0341-2679 VL - 44 IS - 11/12 SP - 26 EP - 29 ER - TY - JOUR A1 - Kuperjans, Isabel A1 - Esser, J. A1 - Meyer, Jörg A1 - Donner, O. T1 - Gestaltung und Bewertung von Energieanlagen unter ökologischen, wirtschaftlichen und technischen Gesichtspunkten JF - Umweltwirtschaftsforum : UWF Y1 - 2000 SN - 0943-3481 VL - 8 IS - 3 SP - 53 EP - 58 ER - TY - JOUR A1 - Kuperjans, Isabel T1 - Gute Planung ist alles : Energieeffizienz in der Pharmaproduktion JF - Pharma + Food Y1 - 2011 SN - 1434-8942 VL - 2011 IS - 2 SP - 8 EP - 10 PB - Hüthig CY - Heidelberg ER - TY - JOUR A1 - Augenstein, Eckardt A1 - Herbergs, S. A1 - Kuperjans, Isabel T1 - TOP-Energy : ein Werkzeug zur Optimierung der Gebäudeenergieversorgung JF - KI : Kälte, Luft, Klimatechnik Y1 - 2006 SN - 1865-5432 IS - 5 SP - 198 EP - 201 ER - TY - JOUR A1 - Marx, Ulrich A1 - Schenk, Friedrich A1 - Behrens, Jan A1 - Meyr, Ulrike A1 - Wanek, Paul A1 - Zang, Werner A1 - Schmitt, Robert A1 - Brüstle, Oliver A1 - Zenke, Martin A1 - Klocke, Fritz T1 - Automatic production of induced pluripotent stem cells JF - Procedia CIRP : First CIRP Conference on BioManufacturing Y1 - 2013 SN - 2212-8271 VL - Vol. 5 SP - 2 EP - 6 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Srivastava, A. A1 - Lahiri, S. A1 - Maiti, M. A1 - Knolle, F. A1 - Hoyler, Friedrich A1 - Scherer, Ulrich W. A1 - Schnug, E. W. T1 - Study of naturally occurring radioactive material (NORM) in top soil of Punjab State from the North Western part of India JF - Journal of Radioanalytical and Nuclear Chemistry Y1 - 2014 U6 - http://dx.doi.org/0.1007/s10967-014-3450-1 SN - 1588-2780 (E-Journal); 0022-4081 (Print); 0134-0719 (Print); 0236-5731 (Print); 1417-2097 (Print) VL - 2014 IS - 302 SP - 1049 EP - 1052 PB - Springer Nature CY - Basel ER - TY - JOUR A1 - Jildeh, Zaid B. A1 - Wagner, Torsten A1 - Schöning, Michael Josef A1 - Pieper, Martin T1 - Simulating the electromagnetic‐thermal treatment of thin aluminium layers for adhesion improvement JF - Physica status solidi (a) N2 - A composite layer material used in packaging industry is made from joining layers of different materials using an adhesive. An important processing step in the production of aluminium-containing composites is the surface treatment and consequent coating of adhesive material on the aluminium surface. To increase adhesion strength between aluminium layer and the adhesive material, the foil is heat treated. For efficient heating, induction heating was considered as state-of-the-art treatment process. Due to the complexity of the heating process and the unpredictable nature of the heating source, the control of the process is not yet optimised. In this work, a finite element analysis of the process was established and various process parameters were studied. The process was simplified and modelled in 3D. The numerical model contains an air domain, an aluminium layer and a copper coil fitted with a magnetic field concentrating material. The effect of changing the speed of the aluminium foil (or rolling speed) was studied with the change of the coil current. Statistical analysis was used for generating a general control equation of coil current with changing rolling speed. Y1 - 2015 U6 - http://dx.doi.org/10.1002/pssa.201431893 SN - 1862-6319 VL - Vol. 212 IS - 6 SP - 1234 EP - 1241 PB - Wiley CY - Weinheim ER - TY - JOUR A1 - Borchert, Jörg A1 - Hasenbeck, Marc A1 - Jungbluth, Christian A1 - Schemm, Ralf T1 - Bewertung und Steuerung von Gasspeichern bzw. Gasspeicherscheiben JF - Zeitschrift für Energiewirtschaft N2 - In diesem Artikel werden zunächst einleitend der Gasmarkt Deutschland und der sich daraus ergebende Speicherbedarf skizziert. Folgend wird auf verschiedene Speichernutzen aus betriebswirtschaftlicher Perspektive eingegangen und die in diesem Artikel vorgestellten Bewertungsverfahren einleitend beschrieben. In diesem Artikel werden stochastische Optimierungsmethoden aufgegriffen, die sowohl eine Bewertung der Speicher gegenüber einem Spotpreis, als auch gegenüber einer gesamten Forwardcurve ermöglichen. Hierzu werden zunächst Modelle zur Beschreibung der Marktpreise vorgestellt und anhand empirischer Daten kalibriert. Dann wird eine beispielhafte Speicherscheibe zunächst auf Basis der LeastSquareMonteCarloTechnik gegenüber dem stochastischen mehrfaktoriellen Spotpreismodell bewertet. Hieran schließt sich die Vorstellung der Bewertung sowie des Hedgings gegenüber der Forwardcurve an. Abschließend erfolgt eine vergleichende Gegenüberstellung beider Verfahren. Y1 - 2009 U6 - http://dx.doi.org/10.1007/s12398-009-0033-x SN - 1866-2765 VL - 33 IS - 4 SP - 279 EP - 293 PB - Springer CY - Berlin ER - TY - JOUR A1 - Borchert, Jörg A1 - Hasenbeck, Marc T1 - Bewertung und Steuerung von Kraftwerksscheiben JF - Zeitschrift für Energiewirtschaft Y1 - 2009 U6 - http://dx.doi.org/10.1007/s12398-009-0014-0 SN - 1866-2765 VL - 33 IS - 2 SP - 115 EP - 126 PB - Vieweg CY - Wiesbaden ER -