TY - CHAP A1 - Herzog, Rudolf T1 - Das Oberflächenabflussmodell von Keser und die Grenzwertmethode : Die Abflussbildung im Vergleich. N2 - Dipl.-Ing. Rudolf Herzog , Rehm Software Berg / Ravensburg. 9 S. (S. 94-102). Beitrag zum 1. Aachener Softwaretag in der Wasserwirtschaft a1, 2007, Aachen>. Zusammenfassung [des Autors] Die grundlegenden Ansätze der beiden Modelle sind ähnlich. Der hauptsächliche Unterschied liegt darin, dass die Grenzwertmethode die Angabe einer Bodenart erfordert, die ihrerseits wieder Probleme verursachen kann. Es kann nicht davon ausgegangen werden, dass die Bodenarten homogen anliegen. Die ersatzweise Vorgabe einer für alle Einzugsgebiete einheitlichen Bodenart hilft da nicht wirklich weiter. Es stellt sich vielmehr die Frage, ob der zusätzliche Aufwand eine signifikante Verbesserung des Ereignisses zur Folge hat. Der Vorteil der Grenzwertmethode liegt auf der Hand: Die Parameterwahl ermöglicht eine flexible Steuerung des Modells, in die Abflussbildung kann differenziert eingegriffen werden. Das NA-Geschehen kann weitgehend kalibriert werden. Es ist allerdings auch zu bedenken, dass die Flexibilität des Modells risikobehaftet ist - die Abflussbildung kann nach Belieben beeinflusst werden. Fazit: Flexibel in der Anwendung, bei NA-Messung empfehlenswert. Im Allgemeinen geringere Abflussmengen als Keser. Die Blackbox von Keser ist zwar nicht steuerbar, entzieht sich damit aber auch Wissensdefiziten und Manipulationseinflüssen. Über Parameter und deren Auswirkungen muss nicht spekuliert werden. Wenn mehrere Personen mit dem Modell von Keser arbeiten, ergeben sich im Gegensatz zur Grenzwertmethode zwangsweise dieselben Ergebnisse - gleiche geometrische Oberflächendaten vorausgesetzt. Außerdem kommt Keser ohne die Bodenart aus. Fazit: Bei BFG >20%, einfache Handhabung, geringer Aufwand. Gegenüber der Grenzwertmethode (mittlere Verhältnisse) jedoch etwas höhere Abflüsse. Das Programmpaket HYKAS der Fa. Rehm Software ermöglicht u.a. den Nachweis von Kanalnetzen und bietet in diesem Zusammenhang beide Modellansätze zur Auswahl an. Der Programmanwender kann damit eine am Datenbestand bzw. an den Vorgaben des Auftraggebers ausgerichtete Modellauswahl treffen. Die realitätsnahe Ermittlung der Oberflächenabflüsse ist kompliziert. Weitere Unwegsamkeiten warten nach der Abflussbildung bei der Abflusskonzentration auf: Es ist z.B. die Festlegung der Fließlänge auf der Oberfläche erforderlich... Es ist noch ein weiter Weg bis zur Kläranlage. KW - Entwässerung KW - Abflussmessung KW - Abflussbildung KW - Oberflächenabflussmodell Y1 - 2007 ER - TY - CHAP A1 - Klöcker, Alexander T1 - Das Leitungsbauunternehmen - unternehmerische Strategie als Zukunftssicherung N2 - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 21-22 Zusammenfassung des Vortrags KW - Leitungsbau KW - Leitungsbauunternehmen Y1 - 2006 ER - TY - JOUR A1 - Gossla, Ulrich A1 - Falkner, H. T1 - Das Gebrauchsverhalten von Betonböden bei unterschiedlichen Bewehrungskonzepten / Falkner, H; Gossla, U. JF - Industrieböden '99 : internationales Kolloquium, 12. - 14. Januar 1999 = Industrial floors '99 / Technische Akademie Esslingen. Hrsg.: P. Seidler Y1 - 1999 SN - 392481340X N1 - Internationales Kolloquium Industrieböden ; (4, 1999, Ostfildern) SP - 281 EP - 286 PB - Technische Akademie Esslingen CY - Ostfildern ER - TY - JOUR A1 - Höttges, Jörg A1 - Wallis, Steve G. A1 - Guymer, Ian T1 - Das ATZ-Modell zur Vorhersage des Schadstofftransports in Flüssen JF - Wasserwirtschaft. 82 (1992), H. 10 Y1 - 1992 SN - 0043-0978 SP - 494 EP - 497 ER - TY - CHAP A1 - Duffner, Markus A1 - Uibel, Thomas A1 - Peterson, Leif Arne A1 - Moorkamp, Wilfried ED - Fouad, Nabil A. T1 - Cross Layers Light – Ein ressourceneffizientes und recyclebares Holz-Wandsystem T2 - Bauphysik Kalender 2023: Nachhaltigkeit N2 - Ein neues tragendes, lagenweise aufgebautes Holzbau-Wandsystem und seine ökonomische und statische Entwicklung werden vorgestellt. Randbedingungen wie Nachhaltigkeit, Ressourceneffizienz und eine beanspruchungsadaptive Konstruktionsweise sind für diese innovative Bauteilentwicklung von zentraler Bedeutung. Eine wesentliche Herausforderung ist die Herstellung der Verbindung der Lagen untereinander zu einem bauphysikalisch und statisch leistungsfähigen Wandsystem. Die Tragfähigkeit und Steifigkeit verschiedener Verbindungsvarianten wurden ebenso wie die Eigenschaften der Wandelemente analytisch, numerisch und experimentell untersucht. Y1 - 2023 SN - 9783433033890 (Print) SN - 9783433611289 (Online) U6 - http://dx.doi.org/10.1002/9783433611289.ch13 SP - 483 EP - 501 PB - Ernst & Sohn CY - Berlin ER - TY - CHAP A1 - Jockwer, R. A1 - Kleiber, M. A1 - Uibel, Thomas ED - Görlacher, Rainer T1 - Criteria for Evaluating the Simplification of Design Rules for Dowel-type Fasteners T2 - International Network on Timber Engineering Research, INTER : proceedings, meeting 51, 10 - 13 August 2016, Tallinn, Estonia Y1 - 2018 SP - 461 EP - 466 PB - Timber Scientific Publishing, KIT Holzbau und Baukonstruktionen CY - Karlsruhe ER - TY - JOUR A1 - Wolisz, Henryk A1 - Schütz, Thomas A1 - Blanke, Tobias A1 - Hagenkamp, Markus A1 - Kohrn, Markus A1 - Wesseling, Mark A1 - Müller, Dirk T1 - Cost optimal sizing of smart buildings' energy system components considering changing end-consumer electricity markets JF - Energy Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.energy.2017.06.025 VL - 137 SP - 715 EP - 728 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Biener, Ernst A1 - Sasse, T. T1 - Construction of composite lining systems under unfavourable weather conditions JF - Landfilling of waste: barriers / ed. by T. H. Christensen; R. Cossu; R. Stegmann. - 1. Aufl. Y1 - 1994 SN - 0419159908 SP - 183 EP - 200 PB - Spon CY - London [u.a.] ER - TY - JOUR A1 - Biener, Ernst A1 - Sasse, T. T1 - Construction and rehabilitation of landfill shafts JF - Sardinia 93 : Fourth International Landfill Symposium "Barrier systems, environmental aspects, upgrading and remediation, siting, monofills, effects of waste pretreatment, landfilling in developing countries" ; 11 - 15 October 1993, S. Margherita di Pula (Cagliari), Sardinia, Italy ; proceedings / coord. by Thomas H. Christensen ... - Bd. 1 Y1 - 1993 N1 - International Landfill Symposium <4, 1993, Santa Margherita, Pula> SP - 451 EP - 460 PB - CISA, Environmental Sanitary Engineering Centre CY - Cagliari ER - TY - JOUR A1 - Cheenakula, Dheeraja A1 - Griebel, Kai A1 - Montag, David A1 - Grömping, Markus ED - Huang, Xiaowu T1 - Concept development of a mainstream deammonification and comparison with conventional process in terms of energy, performance and economical construction perspectives JF - Frontiers in Microbiology N2 - Deammonification for nitrogen removal in municipal wastewater in temperate and cold climate zones is currently limited to the side stream of municipal wastewater treatment plants (MWWTP). This study developed a conceptual model of a mainstream deammonification plant, designed for 30,000 P.E., considering possible solutions corresponding to the challenging mainstream conditions in Germany. In addition, the energy-saving potential, nitrogen elimination performance and construction-related costs of mainstream deammonification were compared to a conventional plant model, having a single-stage activated sludge process with upstream denitrification. The results revealed that an additional treatment step by combining chemical precipitation and ultra-fine screening is advantageous prior the mainstream deammonification. Hereby chemical oxygen demand (COD) can be reduced by 80% so that the COD:N ratio can be reduced from 12 to 2.5. Laboratory experiments testing mainstream conditions of temperature (8–20°C), pH (6–9) and COD:N ratio (1–6) showed an achievable volumetric nitrogen removal rate (VNRR) of at least 50 gN/(m3∙d) for various deammonifying sludges from side stream deammonification systems in the state of North Rhine-Westphalia, Germany, where m3 denotes reactor volume. Assuming a retained Norganic content of 0.0035 kgNorg./(P.E.∙d) from the daily loads of N at carbon removal stage and a VNRR of 50 gN/(m3∙d) under mainstream conditions, a resident-specific reactor volume of 0.115 m3/(P.E.) is required for mainstream deammonification. This is in the same order of magnitude as the conventional activated sludge process, i.e., 0.173 m3/(P.E.) for an MWWTP of size class of 4. The conventional plant model yielded a total specific electricity demand of 35 kWh/(P.E.∙a) for the operation of the whole MWWTP and an energy recovery potential of 15.8 kWh/(P.E.∙a) through anaerobic digestion. In contrast, the developed mainstream deammonification model plant would require only a 21.5 kWh/(P.E.∙a) energy demand and result in 24 kWh/(P.E.∙a) energy recovery potential, enabling the mainstream deammonification model plant to be self-sufficient. The retrofitting costs for the implementation of mainstream deammonification in existing conventional MWWTPs are nearly negligible as the existing units like activated sludge reactors, aerators and monitoring technology are reusable. However, the mainstream deammonification must meet the performance requirement of VNRR of about 50 gN/(m3∙d) in this case. KW - anammox KW - energy efficiency KW - mainstream deammonification KW - nitrogen elimination KW - wastewater Y1 - 2023 U6 - http://dx.doi.org/10.3389/fmicb.2023.1155235 SN - 1664-302X VL - 14 IS - 11155235 SP - 1 EP - 15 PB - Frontiers ER - TY - JOUR A1 - Laumann, Jörg A1 - Kindmann, Rolf T1 - Computerorientierte Lösung von Stabilitäts¬problemen im Bauwesen / Kindmann, R. ; Laumann, J. JF - Computer im Bauwesen : Festschrift zum 60. Geburtstag von Prof. Hartmann / Karlheinz Lehner (Hrsg.) Y1 - 2004 SN - 3-8322-2478-5 N1 - Festschrift Dietrich Hartmann SP - 15 EP - 24 PB - Shaker CY - Aachen ER - TY - CHAP A1 - Oertel, Mario A1 - Bung, Daniel B. T1 - Comparison of 2D dam-break waves with VOF and SPH method T2 - Proceedings of the 35th IAHR world congress : 8.-13.9.2013, Chengdu, China Y1 - 2013 SP - Artikelkennnummer: A11113 PB - Tsinghua Univ. Press CY - Beijing ER - TY - JOUR A1 - Höttges, Jörg A1 - Arnold, Uwe A1 - Rouvé, Gerhard T1 - Combined Digital Image and Finite Element Analysis of Mixing in Compound Open Channel Flow / Arnold, U.; J. Höttges; G. Rouvé JF - Refined flow modelling and turbulence measurements : proceedings of the Third International Symposium Tokyo, Japan 26 - 28 July, 1988 / ed. by Y. Iwasa. Scientific Organizing Committee of the Third International Symposium on Refined Flow Modelling and Tur Y1 - 1989 SN - 4-946443-03-7 N1 - International Symposium on Refined Flow Modelling and Turbulence Measurements <3, 1988, Tōkyō> SP - 569 EP - 576 PB - Universal Acad. Press CY - Tokyo ER - TY - JOUR A1 - Valero, D. A1 - Bung, Daniel B. A1 - Crookston, B. M. T1 - Closure to “Energy Dissipation of a Type III Basin under Design and Adverse Conditions for Stepped and Smooth Spillways” JF - Journal of Hydraulic Engineering Y1 - 2019 U6 - http://dx.doi.org/10.1061/(ASCE)HY.1943-7900.0001669 VL - 146 IS - 2 PB - ASCE CY - Reston, Va. ER - TY - JOUR A1 - Jochim, Haldor E. T1 - Charging rail operators for delays – how not to do it JF - Networks for mobility : International Symposium, September 18 - 20, 2002, Stuttgart, Germany ; proceedings / University of Stuttgart, Centre of Transporation Research (FOVUS). W. Möhlenbrink ... (eds.) Y1 - 2002 SN - 3893010858 N1 - International Symposium ; (2002.09.18-20 : ; Stuttgart) PB - FOVUS CY - Stuttgart ER - TY - CHAP A1 - Oertel, Mario A1 - Bung, Daniel B. T1 - Characteristics of cross-bar block ramp flows T2 - Hydraulic structures into the 21st century : 4th IAHR International Symposium on Hydraulic Structures : 9.-11.2.2012, Porto Y1 - 2012 SN - 978-989-8509-01-7 ER - TY - CHAP A1 - Melzner, Jürgen A1 - Ferger, Martin ED - Krause, Thomas ED - Ulke, Bernd ED - Ferger, Martin T1 - Building Information Modeling T2 - Zahlentafeln für den Baubetrieb N2 - Durch die Einführung von Building Information Modeling (BIM) sowohl projektspezifisch als auch in ganze Unternehmungen hat die Baubranche einen weitreichenden Veränderungsprozess angestoßen. Building Information Modeling kann als eine Methode angesehen werden, um die Informationsasymmetrien zwischen den Projektbeteiligten so gering wie möglich zu halten. Y1 - 2024 SN - 978-3-658-41329-3 (Print) SN - 978-3-658-41330-9 (eBook) U6 - http://dx.doi.org/10.1007/978-3-658-41330-9_15 SP - 1051 EP - 1073 PB - Springer Vieweg CY - Wiesbaden ER - TY - RPRT A1 - Sansom, M. A1 - Lawson, R.M. A1 - Tucho, R. A1 - Kendrick, C. A1 - Ogden, R. A1 - Resalati, S. A1 - Garay, R. A1 - Döring, Bernd A1 - Reger, V. A1 - Gilbert, J. A1 - Heikkinen, J. A1 - Hemmila, K. T1 - Building in active thermal mass into steel structures (BATIMASS) - EUR 28166EN N2 - The main objective of the BATIMASS project was to address how the energy balance in relatively lightweight steel buildings can be improved by building in ‘active thermal mass’ (ATM) into the building fabric. This was achieved through concept design, dynamic thermal modelling and testing of a number of potentially viable systems and concepts. A significant programme of thermal simulation modelling was undertaken utilising the thermally equivalent slab (TES) concept to model the passive thermal capacity effect of profiled, composite metal floor decks. It is apparent from the modelling results that thermal mass is a highly complex phenomenon which is highly dependent upon building type, occupancy patterns, climate and many other aspects of the building design and servicing strategy. The ATM systems developed, both conceptually and for prototype testing, focussed on water-cooled composite slabs, the Cofradal floor system and the phase change material (PCM) Energain. In addition to laboratory testing of prototypes, whole building monitoring was undertaken at the Kubik building in Spain and the RWTH test building in Germany. Advanced thermal modelling was also undertaken to estimate the likely benefits of the ATM concept designs developed and for comparison with the test results. In addition to thermal testing, structural tests were conducted on composite floor specimens incorporating embedded water pipes. This Final Report presents the results of the activities carried out under this RFCS contract RFSR CT 2012 00033. The work carried out is reported in six major sections corresponding to the technical Work Packages of the project. Only summaries of the work carried out are provided in this report; all work undertaken is fully reported in the formal project deliverables. KW - industrial research KW - iron and steel industry KW - research project KW - materials technology KW - resistance of materials KW - steel KW - metal structure KW - ingot KW - building industry KW - research report Y1 - 2016 SN - 978-92-79-63176-4 U6 - http://dx.doi.org/10.2777/25999 SN - 1831-9424 PB - Publications Office of the European Union CY - Luxembourg ER - TY - BOOK A1 - Blaß, Hans Joachim A1 - Uibel, Thomas ED - Schickhofer, Gerhard T1 - BSPhandbuch : Holz-Massivbauweise in Brettsperrholz; Nachweise auf Basis des neuen europäischen Normenkonzepts Y1 - 2009 SN - 978-3-85125-076-3 PB - Verl. der Techn. Univ. CY - Graz ER - TY - JOUR A1 - Gossla, Ulrich T1 - Brückenbau in Japan. Faserverbundwerkstoffe fuer neuartige Hybridenkonstruktionen JF - Trends und Entwicklungen im Bauwesen / Braunschweiger Bauseminar 2000, 9. und 10. November. Institut für Baustoffe, Massivbau und Brandschutz, IBMBM, TU Braunschweig ; Materialprüfanstalt für das Bauwesen - MPA Braunschweig. Wiss. Leitung: Horst Falkner ; Manfred Teutsch Y1 - 2000 SN - 3-89288-131-6 N1 - Institut für Baustoffe, Massivbau und Brandschutz, IBMB, TU Braunschweig - Materialprüfanstalt für das Bauwesen, MPA Braunschweig ; H. 152 SP - 119 EP - 126 PB - IBMB, Bibliothek CY - Braunschweig ER -