TY  - JOUR
A1  - El Quardi, A.
A1  - Streckert, J.
A1  - Bitz, Andreas
A1  - Münkner, S.
A1  - Engel, J.
A1  - Hansen, V.
T1  - New fin-line devices for radiofrequency exposure of small biological samples in vitro allowing whole-cell patch clamp recordings
JF  - Bioelectromagnetics
N2  - The development and analysis of three waveguides for the exposure of small biological in vitro samples to mobile communication signals at 900 MHz (GSM, Global System for Mobile Communications), 1.8 GHz (GSM), and 2 GHz (UMTS, Universal Mobile Telecommunications System) is presented. The waveguides were based on a fin-line concept and the chamber containing the samples bathed in extracellular solution was placed onto two fins with a slot in between, where the exposure field concentrates. Measures were taken to allow for patch clamp recordings during radiofrequency (RF) exposure. The necessary power for the achievement of the maximum desired specific absorption rate (SAR) of 20 W/kg (average over the mass of the solution) was approximately Pin = 50 mW, Pin = 19 mW, and Pin = 18 mW for the 900 MHz, 1800 MHz, and 2 GHz devices, respectively. At 20 W/kg, a slight RF-induced temperature elevation in the solution of no more than 0.3 °C was detected, while no thermal offsets due to the electromagnetic exposure could be detected at the lower SAR settings (2, 0.2, and 0.02 W/kg). A deviation of 10% from the intended solution volume yielded a calculated SAR deviation of 8% from the desired value. A maximum ±10% variation in the local SAR could occur when the position of the patch clamp electrode was altered within the area where the cells to be investigated were located.
Y1  - 2011
U6  - http://dx.doi.org/10.1002/bem.20621
SN  - 1521-186X
VL  - 32
IS  - 2
SP  - 102
EP  - 112
PB  - Wiley
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Bitz, Andreas
A1  - Zhou, Yi
A1  - El Quardi, Abdessamad
A1  - Streckert, Joachim
T1  - Occupational Exposure at Mobile Communication Base Station Antenna Sites
JF  - Frequenz
Y1  - 2009
U6  - http://dx.doi.org/10.1515/FREQ.2009.63.7-8.123
SN  - 2191-6349
VL  - 63
IS  - 7-8
SP  - 123
EP  - 128
ER  - 
TY  - JOUR
A1  - Kraff, Oliver
A1  - Bitz, Andreas
A1  - Kruszona, Stefan
A1  - Orzada, Stephan
A1  - Schaefer, Lena C.
A1  - Theysohn, Jens M.
A1  - Maderwald, Stefan
A1  - Ladd, Mark E.
A1  - Quick, Harald H.
T1  - An eight-channel phased array RF coil for spine MR imaging at 7 T
JF  - Investigative Radiology
Y1  - 2009
U6  - http://dx.doi.org/10.1097/RLI.0b013e3181b24ab7
SN  - 1536-0210
VL  - 44
IS  - 11
SP  - 734
EP  - 740
PB  - Lippincott Williams & Wilkins
ER  - 
TY  - JOUR
A1  - Klomp, D. W. J.
A1  - Bitz, Andreas
A1  - Heerschap, A.
A1  - Scheenen, T. W. J.
T1  - Proton spectroscopic imaging of the human prostate at 7 T
JF  - NMR in Biomedicine
Y1  - 2009
U6  - http://dx.doi.org/10.1002/nbm.1360
SN  - 1099-1492
VL  - 22
IS  - 5
SP  - 495
EP  - 501
ER  - 
TY  - JOUR
A1  - Lerchl, Alexander
A1  - Krüger, Heike
A1  - Niehaus, Michael
A1  - Streckert, Joachim R.
A1  - Bitz, Andreas
A1  - Hansen, Volkert
T1  - Effects of mobile phone electromagnetic fields at nonthermal SAR values on melatonin and body weight of Djungarian hamsters (Phodopus sungorus)
JF  - Journal of Pineal Research
Y1  - 2008
U6  - http://dx.doi.org/10.1111/j.1600-079X.2007.00522.x
SN  - 1600-079X
VL  - 44
IS  - 3
SP  - 267
EP  - 272
ER  - 
TY  - JOUR
A1  - Reinhardt, T.
A1  - Bitz, Andreas
A1  - El Ouardi, A.
A1  - Streckert, J.
A1  - Sommer, A.
A1  - Lerchl, A.
A1  - Hansen, V.
T1  - Exposure set-ups for in vivo experiments using radial waveguides
JF  - Radiation Protection Dosimetry
Y1  - 2007
U6  - http://dx.doi.org/10.1093/rpd/ncm370
SN  - 1742-3406
VL  - 124
IS  - 1
SP  - 21
EP  - 26
ER  - 
TY  - JOUR
A1  - Sommer, Angela M.
A1  - Bitz, Andreas
A1  - Streckert, Joachim
A1  - Hansen, Volkert W.
A1  - Lerchl, Alexander
T1  - Lymphoma development in mice chronically exposed to UMTS-modulated radiofrequency electromagnetic fields
JF  - Radiation Research
Y1  - 2007
U6  - http://dx.doi.org/10.1667/RR0857.1
SN  - 1938-5404
VL  - 168
IS  - 1
SP  - 72
EP  - 80
ER  - 
TY  - JOUR
A1  - Sukhotina, Irina
A1  - Streckert, Joachim R.
A1  - Bitz, Andreas
A1  - Hansen, Volkert W.
A1  - Lerchl, Alexander
T1  - 1800 MHz electromagnetic field effects on melatonin release from isolated pineal glands
JF  - Journal of Pineal Research
Y1  - 2006
U6  - http://dx.doi.org/10.1111/j.1600-079X.2005.00284.x
SN  - 1600-079X
VL  - 40
IS  - 1
SP  - 86
EP  - 91
ER  - 
TY  - JOUR
A1  - Franke, Helmut
A1  - Streckert, Joachim
A1  - Bitz, Andreas
A1  - Goeke, Johannes
A1  - Hansen, Volkert
A1  - Ringelstein, E. Bernd
A1  - Nattkämper, Heiner
A1  - Galle, Hans-Joachim
A1  - Stögbauer, Florian
T1  - Effects of Universal Mobile Telecommunications System (UMTS) electromagnetic fields on the blood-brain barrier in vitro
JF  - Radiation Research
Y1  - 2005
U6  - http://dx.doi.org/10.1667/RR3424.1
SN  - 1938-5404
VL  - 164
IS  - 3
SP  - 258
EP  - 269
ER  - 
TY  - JOUR
A1  - Wissen, M.
A1  - Bogdanski, N.
A1  - Scheer, H.-C.
A1  - Bitz, Andreas
A1  - Ahrens, G.
A1  - Gruetzner, G.
T1  - Implication of the light polarisation for UV curing of pre-patterned resists
JF  - Microelectronic Engineering
Y1  - 2005
U6  - http://dx.doi.org/10.1016/j.mee.2004.12.099
SN  - 0167-9317
VL  - 78-79
SP  - 659
EP  - 664
ER  - 
TY  - JOUR
A1  - Schopp, Christoph
A1  - Doll, Timo
A1  - Gräser, Ulrich
A1  - Harzheim, Thomas
A1  - Heuermann, Holger
A1  - Kling, Rainer
A1  - Marso, Michael
T1  - Capacitively Coupled High-Pressure Lamp Using Coaxial Line Networks
JF  - IEEE Transactions on Microwave Theory and Techniques
N2  - This paper describes the development of a capacitively coupled high-pressure lamp with input power between 20 and 43 W at 2.45 GHz, using a coaxial line network. Compared with other electrodeless lamp systems, no cavity has to be used and a reduction in the input power is achieved. Therefore, this lamp is an alternative to the halogen incandescent lamp for domestic lighting. To serve the demands of domestic lighting, the filling of the lamp is optimized over all other resulting requirements, such as high efficacy at low induced powers and fast startups. A workflow to develop RF-driven plasma applications is presented, which makes use of the hot S-parameter technique. Descriptions of the fitting process inside a circuit and FEM simulator are given. Results of the combined ignition and operation network from simulations and measurements are compared. An initial prototype is built and measurements of the lamp's lighting properties are presented along with an investigation of the efficacy optimizations using large signal amplitude modulation. With this lamp, an efficacy of 135 lmW -1 is achieved.
Y1  - 2016
U6  - http://dx.doi.org/10.1109/TMTT.2016.2600326
SN  - 0018-9480
VL  - 64
IS  - 10
SP  - 3363
EP  - 3368
PB  - IEEE
CY  - New York, NY
ER  - 
TY  - JOUR
A1  - Rietsch, Stefan H. G.
A1  - Pfaffenrot, Viktor
A1  - Bitz, Andreas
A1  - Orzada, Stephan
A1  - Brunheim, Sascha
A1  - Lazik-Palm, Andrea
A1  - Theysohn, Jens M.
A1  - Ladd, Mark E.
A1  - Quick, Harald H.
A1  - Kraff, Oliver
T1  - An 8-channel transceiver 7-channel receive RF coil setup for high SNR ultrahigh-field MRI of the shoulder at 7T
JF  - Medical Physics
Y1  - 2017
U6  - http://dx.doi.org/10.1002/mp.12612
SN  - 0094-2405
IS  - Article in press
PB  - Wiley
CY  - Hoboken
ER  - 
TY  - CHAP
A1  - Endress, Tim
A1  - Bragard, Michael
T1  - Recording of efficiency-maps of low-power electric drive systems using a flexible matlab-based test bench
T2  - 2017 IEEE 58th International Scientific Conference on Power and Electrical Engineering of Riga Technical University (RTUCON)
N2  - This paper introduces a hardware setup to measure efficiency maps of low-power electric motors and their associated inverters. Here, the power of the device under test (DUT) ranges from some Watts to a few hundred Watts. The torque and speed of the DUT are measured independent of voltage and current in multiple load points. A Matlab-based software approach in combination with an open Texas-Instruments (TI) hardware setup ensures flexibility. Exemplarily, the efficiency field of a Permanent Magnet Synchronous Machine (PMSM) is measured to proof the concept. Brushless-DC (BLDC) motors can be tested as well. The nomenclature in this paper is based on the new European standard DIN EN 50598. Special attention is paid to the calculation of the measurement error.
Y1  - 2017
SN  - 978-1-5386-3846-0
U6  - http://dx.doi.org/10.1109/RTUCON.2017.8124775
PB  - IEEE
CY  - New York
ER  - 
TY  - CHAP
A1  - Niemueller, Tim
A1  - Neumann, Tobias
A1  - Henke, Christoph
A1  - Schönitz, Sebastian
A1  - Reuter, Sebastian
A1  - Ferrein, Alexander
A1  - Jeschke, Sabina
A1  - Lakemeyer, Gerhard
T1  - Improvements for a robust production in the RoboCup logistics league 2016
T2  - RoboCup 2016: Robot World Cup XX. RoboCup 2016.
Y1  - 2017
SN  - 978-3-319-68792-6
U6  - http://dx.doi.org/10.1007/978-3-319-68792-6_49
SP  - 589
EP  - 600
PB  - Springer
CY  - Cham
ER  - 
TY  - JOUR
A1  - Orzada, Stephan
A1  - Bitz, Andreas
A1  - Johst, Sören
A1  - Gratz, Marcel
A1  - Völker, Maximilian N.
A1  - Kraff, Oliver
A1  - Abuelhaija, Ashraf
A1  - Fiedler, Thomas M.
A1  - Solbach, Klaus
A1  - Quick, Harald H.
A1  - Ladd, Mark E.
T1  - Analysis of an integrated 8-Channel Tx/Rx body array for use as a body coil in 7-Tesla MRI
JF  - Frontiers in Physics
Y1  - 2017
U6  - http://dx.doi.org/10.3389/fphy.2017.00017
SN  - 2296-424X
N1  - Article number 17
VL  - 5
IS  - Jun
ER  - 
TY  - JOUR
A1  - Ferrein, Alexander
A1  - Steinbauer, Gerald
T1  - The Interplay of Aldebaran and RoboCup
JF  - KI - Künstliche Intelligenz
Y1  - 2016
U6  - http://dx.doi.org/10.1007/s13218-016-0440-1
SN  - 1610-1987
VL  - 30
IS  - 3-4
SP  - 325
EP  - 326
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Steinbauer, Gerald
A1  - Ferrein, Alexander
T1  - 20 Years of RoboCup
JF  - KI - Künstliche Intelligenz
Y1  - 2016
U6  - http://dx.doi.org/10.1007/s13218-016-0442-z
SN  - 1610-1987
VL  - 30
IS  - 3-4
SP  - 221
EP  - 224
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Ferrein, Alexander
A1  - Steinbauer, Gerald
T1  - Looking back on 20 Years of RoboCup
JF  - KI - Künstliche Intelligenz
Y1  - 2016
U6  - http://dx.doi.org/10.1007/s13218-016-0443-y
SN  - 1610-1987
VL  - 30
IS  - 3-4
SP  - 321
EP  - 323
PB  - Springer
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Niemueller, Tim
A1  - Zwilling, Frederik
A1  - Lakemeyer, Gerhard
A1  - Löbach, Matthias
A1  - Reuter, Sebastian
A1  - Jeschke, Sabina
A1  - Ferrein, Alexander
T1  - Cyber-Physical System Intelligence
T2  - Industrial Internet of Things
N2  - Cyber-physical systems are ever more common in manufacturing industries. Increasing their autonomy has been declared an explicit goal, for example, as part of the Industry 4.0 vision. To achieve this system intelligence, principled and software-driven methods are required to analyze sensing data, make goal-directed decisions, and eventually execute and monitor chosen tasks. In this chapter, we present a number of knowledge-based approaches to these problems and case studies with in-depth evaluation results of several different implementations for groups of autonomous mobile robots performing in-house logistics in a smart factory. We focus on knowledge-based systems because besides providing expressive languages and capable reasoning techniques, they also allow for explaining how a particular sequence of actions came about, for example, in the case of a failure.
KW  - Smart factory
KW  - Industry 4.0
KW  - Multi-robot systems
KW  - Autonomous mobile robots
KW  - RoboCup
Y1  - 2017
SN  - 978-3-319-42559-7
U6  - http://dx.doi.org/10.1007/978-3-319-42559-7_17
N1  - Springer Series in Wireless Technology
SP  - 447
EP  - 472
PB  - Springer
CY  - Cham
ER  - 
TY  - CHAP
A1  - Stopforth, Riaan
A1  - Davrajh, Shaniel
A1  - Ferrein, Alexander
T1  - South African robotics entity for a collaboration initiative
T2  - Pattern Recognition Association of South Africa and Robotics and Mechatronics International Conference (PRASA-RobMech), 2016
Y1  - 2017
SN  - 978-1-5090-3335-5
U6  - http://dx.doi.org/10.1109/RoboMech.2016.7813144
N1  - PRASA-RobMech, Nov. 30 2016-Dec. 2 2016, Stellenbosch, South Africa
SP  - 1
EP  - 6
PB  - IEEE
ER  -