TY  - JOUR
A1  - Ziemons, Karl
A1  - Bruyndonckx, P.
A1  - Perez, J. M.
A1  - Pietrzyk, U.
A1  - Rato, P.
A1  - Tavernier, S.
T1  - Beyond ClearPET: Next Aims
JF  - 5th IEEE International Symposium on Biomedical Imaging: From Nano to Macro Symposium Proceedings ISBI 2008
N2  - The CRYSTAL CLEAR collaboration, in short CCC, is a consortium of 12 academic institutions, mainly from Europe, joining efforts in the area of developing instrumentation for nuclear medicine and medical imaging. In the framework of the CCC a high performance small animal PET system, called ClearPET, was developed by using new technologies in electronics and crystals in a phoswich arrangement combining two types of lutetium- based scintillator materials: LSO:Ce and LuYAP:Ce. Our next aim will be the development of hybrid image systems. Hybrid MR-PET imaging has many unique advantages for brain research. This has sparked a new research line within CCC for the development of novel MR-PET compatible technologies. MRI is not as sensitive as PET but PET has poorer spatial resolution than MRI. Two major advantages of PET are sensitivity and its ability to acquire metabolic information. To assess these innovations, the development of a 9.4T hybrid animal MR-PET scanner is proposed based on an existing 9.4T MR scanner that will be adapted to enable simultaneous acquisition of MR and PET data using cutting- edge technology for both MR and PET.
Y1  - 2008
SN  - 978-1-4244-2003-2
SP  - 1421
EP  - 1424
ER  - 
TY  - CHAP
A1  - Warerkar, S.
A1  - Schmitz, S.
A1  - Göttsche, Joachim
A1  - Hoffschmidt, Bernhard
A1  - Tamme, R.
T1  - Performance analysis of an air-sand heat exchanger prototype for high-temperature storage
T2  - EuroSun 2008 : 1st International Conference on Solar Heating, Cooling and Buildings ; 7th - 10th October 2008, Lisbon, Portugal : key lectures / ISES, International Solar Energy Society. Vol. 1
Y1  - 2008
SN  - 978-1-61782-228-5
SP  - 2215
EP  - 2222
PB  - Sociedade Portuguesa De Energia Solar (SPES)
CY  - Lissabon
ER  - 
TY  - CHAP
A1  - Wang, W.
A1  - Mensing, C.
A1  - Gligorevic, Snjezana
A1  - Jost, T.
A1  - Dammann, A.
T1  - Short term statistical analysis of outdoor to indoor propagation channel for geolocations
T2  - Proceedings of the 13th International OFDM Workshop : (InOWo '08), Aug. 27./28. 2008, Hamburg : Session 3A: Systems concepts
Y1  - 2008
SP  - 85
EP  - 89
ER  - 
TY  - CHAP
A1  - Wagner, Torsten
A1  - Yoshinobu, T.
A1  - Schöning, Michael Josef
T1  - Light-addressable potentiometric sensor as semiconductor-based sensor platform for (bio-) chemical sensing
T2  - Armenian Journal of Physics
Y1  - 2008
SN  - 1829-1171
SP  - 99
EP  - 103
ER  - 
TY  - JOUR
A1  - Vant, Christianne
A1  - Staat, Manfred
A1  - Baroud, Gamal
T1  - Percutaneous Vertebroplasty: A Review of Two Intraoperative Complications
JF  - Bioengineering in Cell and Tissue Research / Artmann, Gerhard M. ; Chien, Shu (Eds.)
Y1  - 2008
SN  - 978-3-540-75408-4
SP  - 527
EP  - 539
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Turek, M.
A1  - Keusgen, M.
A1  - Poghossian, Arshak
A1  - Mulchandani, A.
A1  - Wang, J.
A1  - Schöning, Michael Josef
T1  - Enzyme-modified electrolyte-insulator-semiconductor sensors
JF  - Journal of Contemporary Physics. 43 (2008), H. 2
Y1  - 2008
SN  - 1934-9378
N1  - Armenian Academy of Sciences
SP  - 82
EP  - 85
ER  - 
TY  - JOUR
A1  - Trilla, Joan
A1  - Grossen, Jürgen
A1  - Robinson, Alexander
A1  - Funke, Harald
A1  - Bosschaerts, Walter
A1  - Hendrick, Patrick
T1  - Development of a hydrogen combustion chamber for an ultra micro gas turbine
JF  - PowerMEMS 2008, 8th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications, microEMS 2008, 2nd Symposium on Micro Environmental Machine Systems, Sendai, JP, Nov 9-12, 2008
Y1  - 2008
SP  - 101
EP  - 104
ER  - 
TY  - CHAP
A1  - Tran, Thanh Ngoc
A1  - Pham, Phu Tinh
A1  - Staat, Manfred
T1  - Reliability analysis of shells based on direct plasticity methods
N2  - Abstracts der CD-Rom Proceedings of the 8th World Congress on Computational Mechanics (WCCM8) and 5th Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2008) 30.06. - 04.07.2008 Venedig, Italien. 2 Seiten Zusammenfassung der Autoren mit graph. Darst. und Literaturverzeichnis
N2  - Abstracts of the Proceedings of the 8th World Congress on Computational Mechanics (WCCM8) and 5th Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2008) June 30th - July, 4th 2008, Venice, Italy. 2 pages with abstracts of the authors, Ill. and references.
KW  - Finite-Elemente-Methode
KW  - Limit analysis
KW  - Shakedown analysis
KW  - First-order reliability method
KW  - second-order reliability method
KW  - Sensitivity
Y1  - 2008
ER  - 
TY  - JOUR
A1  - Tran, Thanh Ngoc
A1  - Kreißig, R.
A1  - Vu, Duc Khoi
A1  - Staat, Manfred
T1  - Upper bound limit and shakedown analysis of shells using the exact Ilyushin yield surface
JF  - Computer & Structures. 86 (2008)
Y1  - 2008
SN  - 0045-7949
SP  - 1683
EP  - 1695
ER  - 
TY  - THES
A1  - Tran, Thanh Ngoc
T1  - Limit and shakedown analysis of plates and shells including uncertainties
Y1  - 2008
N1  - Chemnitz, Techn. Univ., Diss., 2008
ER  - 
TY  - JOUR
A1  - Tippkötter, Nils
A1  - Roikaew, W.
A1  - Ulber, R.
T1  - Nitrate removal from whey concentrate with biotechnological regeneration of the waste water
JF  - European dairy magazine : EDM
Y1  - 2008
SN  - 0936-6318
IS  - 1
SP  - 30
EP  - 32
ER  - 
TY  - CHAP
A1  - Tippkötter, Nils
A1  - Roikaew, W.
A1  - Ulber, R.
T1  - An automated pilot plant for the bioengineering processing of concentrated whey
T2  - European BioPerspectives : in cooperation with BIOTECHNICA 2008 : 7 - 9 October 2008 Hannover, Germany ; book of abstracts ; abstracts, poster programme
Y1  - 2008
SP  - 98
PB  - Dechema
CY  - Frankfurt am Main
ER  - 
TY  - JOUR
A1  - Tippkötter, Nils
A1  - Deterding, A.
A1  - Ulber, Roland
T1  - Determination of acetic acid in fermentation broth by gas-diffusion technique
JF  - Engineering in Life Sciences
N2  - Due to the interfering effects of acetic acid in many fermentation processes, a gas-diffusion technique was developed for the online determination of acetic acid. The measurements were accomplished with a flow diffusion analysis (FDA) unit from the TRACE Analytics GmbH, Braunschweig, Germany. The diffusion analysis is based on the UV-absorbance of acetic acid at 205 nm. The measurement was achieved by the separation of an acceptor and a carrier stream (acidified fermentation broth) using a gas permeable polytetrafluoroethylene (PTFE) membrane, whereby broth constituents that would otherwise disturb the UV-measurement of acetic acid, are held back efficiently. Merely, the fermentation by-products, e.g. formic acid, is capable of diffusing through the membrane. While formic acid can disturb the measurement, carbon dioxide does not absorb at 205 nm. The method operates with time-dependent sample enrichment. During the analysis, a small volume of the acceptor stream is stopped for a defined time interval in the acceptor chamber. During this period, the gaseous acetic acid diffuses through the membrane and is enriched in the acceptor chamber. Subsequently after the enrichment, the acceptor stream flows through a UV-detector. The intensity of the signal is proportional to the acetic acid concentration. Online measurements in bioreactors via a sterile filtration probe have been accomplished. A linear calibration in the range of 0.5–5.0 g/L acetic acid with a relative standard deviation of <5 % was obtained. A sampling rate of 8 samples per hour was possible. The system was applied for the determination of acetic acid in E. coli fermentation broth. The instrument is easy to clean, very user-friendly and does not require any toxic or expensive reagents.
Y1  - 2008
U6  - http://dx.doi.org/10.1002/elsc.200820227
VL  - 8
IS  - 1, Special Issue: Technical Systems for the Use in Life Sciences
SP  - 62
EP  - 67
ER  - 
TY  - JOUR
A1  - Temiz Artmann, Aysegül
A1  - Kayser, Peter
T1  - Why is Sepsis an Ongoing Clinical Challenge? Lipopolysaccharide Effects on Red Blood Cell Volume / Temiz, Aysegül ;  Kayser, Peter
JF  - Bioengineering in Cell and Tissue Research / Artmann, Gerhard M. ; Chien, Shu (Eds.)
Y1  - 2008
SN  - 978-3-540-75408-4
SP  - 497
EP  - 508
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Stulpe, Werner
A1  - Busch, Paul
T1  - The structure of classical extensions of quantum probability theory
JF  - Journal of Mathematical Physics. 49 (2008), H. 3
Y1  - 2008
SN  - 1089-7658
N1  - 032104
SP  - 1
EP  - 22
ER  - 
TY  - JOUR
A1  - Streun, M.
A1  - Beer, S.
A1  - Hombach, T.
A1  - Jahnke, S.
A1  - Khodaverdi, M.
A1  - Larue, H.
A1  - Minwuyelet, S.
A1  - Parl, C.
A1  - Roeb, G.
A1  - Schurr, U.
A1  - Ziemons, Karl
T1  - PlanTIS: A positron emission tomograph for imaging 11C transport in plants
JF  - 2007 IEEE Nuclear Science Symposium Conference Record, Vol. 6
N2  - Plant growth and transport processes are highly dynamic. They are characterized by plant-internal control processes and by strong interactions with the spatially and temporally varying environment. Analysis of structure- function relations of growth and transport in plants will strongly benefit from the development of non-invasive techniques. PlanTIS (Plant Tomographic Imaging System) is designed for non-destructive 3D-imaging of positron emitting radiotracers. It will permit functional analysis of the dynamics of carbon distribution in plants including bulky organs. It will be applicable for screening transport properties of plants to evaluate e.g. temperature adaptation of genetically modified plants. PlanTIS is a PET scanner dedicated to monitor the dynamics of the 11C distribution within a plant while or after assimilation of 11CO2. Front end electronics and data acquisition architecture of the scanner are based on the ClearPETTM system [1]. Four detector modules form one of two opposing detector blocks. Optionally, a hardware coincidence detection between the blocks can be applied. In general the scan duration is rather long (~ 1 hour) compared to the decay time of 11C (20 min). As a result the count rates can vary over a wide range and accurate dead time correction is necessary.
Y1  - 2008
SN  - 1082-3654
SP  - 4110
EP  - 4112
ER  - 
TY  - JOUR
A1  - Stadler, Andreas M.
A1  - Zerlin, Kay
A1  - Digel, Ilya
A1  - Büldt, Georg
A1  - Zaccai, Guiseppe
A1  - Artmann, Gerhard
T1  - Dynamics and interactions of hemoglobin in red blood cells
JF  - Tissue Engineering Part A. 14 (2008), H. 5
Y1  - 2008
SN  - 1937-3341
N1  - TERMIS EU 2008 Porto Meeting June 22–26, 2008 Porto Congress Center–Alfândega Portugal
SP  - 724
EP  - 724
ER  - 
TY  - JOUR
A1  - Stadler, Andreas M.
A1  - Embs, Jan P.
A1  - Digel, Ilya
A1  - Artmann, Gerhard
A1  - Unruh, Tobias
A1  - Büldt, Georg
A1  - Zaccai, Guiseppe
T1  - Cytoplasmic water and hydration layer dynamics in human red blood cells
JF  - Journal of the American Chemical Society. 50 (2008), H. 130
Y1  - 2008
SN  - 1520-5126
SP  - 16852
EP  - 16853
ER  - 
TY  - JOUR
A1  - Stadler, A.  M.
A1  - Digel, Ilya
A1  - Artmann, Gerhard
A1  - Embs, Jan P.
A1  - Zaccai, Joe
A1  - Büldt, Georg
T1  - Hemoglobin Dynamics in Red Blood Cells: Correlation to Body Temperature
JF  - Biophysical Journal. 95 (2008), H. 11
Y1  - 2008
SN  - 1542-0086
SP  - 5449
EP  - 5461
ER  - 
TY  - CHAP
A1  - Staat, Manfred
A1  - Tran, Thanh Ngoc
A1  - Pham, Phu Tinh
T1  - Limit and shakedown reliability analysis by nonlinear programming
N2  - 7th International Conference on Reliability of Materials and Structures (RELMAS 2008). June 17 - 20, 2008 ; Saint Petersburg, Russia. pp 354-358. Reprint with corrections in red Introduction Analysis of advanced structures working under extreme heavy loading such as nuclear power plants and piping system should take into account the randomness of loading, geometrical and material parameters. The existing reliability are restricted mostly to the elastic working regime, e.g. allowable local stresses. Development of the limit and shakedown reliability-based analysis and design methods, exploiting potential of the shakedown working regime, is highly needed. In this paper the application of a new algorithm of probabilistic limit and shakedown analysis for shell structures is presented, in which the loading and strength of the material as well as the thickness of the shell are considered as random variables. The reliability analysis problems may be efficiently solved by using a system combining the available FE codes, a deterministic limit and shakedown analysis, and the First and Second Order Reliability Methods (FORM/SORM). Non-linear sensitivity analyses are obtained directly from the solution of the deterministic problem without extra computational costs.
KW  - Finite-Elemente-Methode
KW  - Limit analysis
KW  - Shakedown analysis
Y1  - 2008
ER  -