TY - JOUR A1 - Alebouyeh Samami, Behzad A1 - Pieper, Martin A1 - Breitbach, Gerd A1 - Hodapp, Josef T1 - Heat production in the windings of the stators of electric machines under stationary condition JF - Heat and mass transfer N2 - In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results. Y1 - 2014 U6 - https://doi.org/10.1007/s00231-014-1371-8 SN - 0947-7411 (Print) ; 1432-1181 (E-Journal) VL - 50 SP - 1707 EP - 1716 PB - Springer CY - Heidelberg ER - TY - JOUR A1 - Guo, Yuanyuan A1 - Seki, Kosuke A1 - Miyamoto, Ko-ichiro A1 - Wagner, Torsten A1 - Schöning, Michael Josef A1 - Yoshinobu, Tatsuo T1 - Novel photoexcitation method for light-addressable potentiometric sensor with higher spatial resolution JF - Applied physics express : APEX N2 - A novel photoexcitation method for the light-addressable potentiometric sensor (LAPS) is proposed to achieve a higher spatial resolution of chemical images. The proposed method employs a combined light source that consists of a modulated light probe, which generates the alternating photocurrent signal, and a ring of constant illumination surrounding it. The constant illumination generates a sheath of carriers with increased concentration which suppresses the spread of photocarriers by enhanced recombination. A device simulation was carried out to verify the effect of constant illumination on the spatial resolution, which demonstrated that a higher spatial resolution can be obtained. Y1 - 2014 U6 - https://doi.org/10.7567/APEX.7.067301 SN - 1882-0786 (E-Journa); 1882-0778 (Print) VL - 7 IS - 6 SP - 067301-4 PB - IOP CY - Bristol ER - TY - JOUR A1 - Whitehead, Mark A1 - Öhlschläger, Peter A1 - Almajhdi, Fahad N. A1 - Alloza, Leonor A1 - Marzábal, Pablo A1 - Meyers, Ann E. A1 - Hitzeroth, Inga I. A1 - Rybicki, Edward P. T1 - Human papillomavirus (HPV) type 16 E7 protein bodies cause tumour regression in mice JF - BMC cancer Y1 - 2014 U6 - https://doi.org/10.1186/1471-2407-14-367 SN - 1471-2407 IS - 14:367 SP - 1 EP - 15 PB - BioMed Central CY - London ER - TY - JOUR A1 - Wagner, Patrick A1 - Doll, Theodor A1 - Schöning, Michael Josef T1 - Engineering of functional interfaces / Patrick Wagner ; Theodor Doll ; Michael J. Schöning (eds.) JF - Physica status solidi (A) : Applications and materials science Y1 - 2014 U6 - https://doi.org/10.1002/pssa.201470241 SN - 1521-396X (E-Book); 1862-6319 (E-Book); 0031-8965 (Print); 1862-6300 (Print) VL - 211 IS - 6 SP - 1339 EP - 1339 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Vieira da Silva, Maria Eugenia A1 - Schwarzer, Klemens A1 - Hoffschmidt, Bernhard A1 - Pinheiro Rodrigues, Frederico A1 - Schwarzer, Tarik A1 - Costa Rocha, Paulo Alexandre T1 - Mass transfer correlation for evaporation–condensation thermal process in the range of 70 °C–95 °C JF - Renewable energy Y1 - 2013 SN - 1879-0682 (E-Journal); 0960-1481 (Print) VL - Vol. 53 SP - 174 EP - 179 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Iding, Hans A1 - Siegert, Petra A1 - Mesch, K. A1 - Pohl, Martina T1 - Application of α-keto acid decarboxylases in biotransformations JF - Biochimica et biophysica acta (BBA) - Protein structure and molecular enzymology Y1 - 1998 SN - 1879-2588 (E-Journal); 0167-4838 (Print) VL - Vol. 1385 IS - Iss. 2 SP - 307 EP - 322 ER - TY - JOUR A1 - Pohl, Martina A1 - Siegert, Petra A1 - Mesch, K. A1 - Bruhn, H. A1 - Grötzinger, Joachim T1 - Active site mutants of pyruvate decarboxylase from Zymomonas mobilis : a site-directed mutagenesis study of L112, I472, I476, E473 and N482 JF - European journal of biochemistry Y1 - 1998 SN - 1432-1033 (E-Journal); 1742-4658 (E-Journal); 0014-2956 (Print); 1742-464X (Print) VL - Vol. 257 IS - Iss. 3 SP - 538 EP - 546 ER - TY - JOUR A1 - Raue, Markus A1 - Wambach, M. A1 - Glöggler, S. A1 - Grefen, Dana A1 - Kaufmann, R. A1 - Abetz, C. A1 - Georgopanos, P. A1 - Handge, U. A. A1 - Mang, Thomas A1 - Blümich, B. A1 - Abetz, V. T1 - Investigation of historical hard rubber ornaments of Charles Goodyear JF - Macromolecular chemistry and physics Y1 - 2014 SN - 1022-1352 VL - Vol. 215 IS - No. 3 SP - 245 EP - 254 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Buschkühle, Peter A1 - Schürmann, Volker A1 - Wollert, Jörg T1 - Abstraction of wireless communication by a convergence middleware in conjunction with a XML-configuration T2 - Information technology and electrical engineering : devices and systems, materials and technologies for the future ; Ilmenau 07 - 10 September 2009 ; 54. IWK Internationales Wissenschaftliches Kolloquium Y1 - 2009 SN - 978-3-938843-44-4 SP - 95 EP - 96 PB - Techn. Univ. CY - Ilmenau ER - TY - JOUR A1 - Schreiber, Marc A1 - Barkschat, Kai A1 - Kraft, Bodo A1 - Zündorf, Albert T1 - Quick Pad Tagger : An Efficient Graphical User Interface for Building Annotated Corpora with Multiple Annotation Layers JF - Computer Science & Information Technology (CS & IT) Y1 - 2015 SN - 978-1-921987-32-8 U6 - https://doi.org/10.5121/csit.2015.50413 SN - 2231 - 5403 VL - 5 IS - 4 SP - 131 EP - 143 PB - Academy & Industry Research Collaboration Center (AIRCC) ER - TY - CHAP A1 - Buda, Aurel A1 - Schürmann, Volker A1 - Wollert, Jörg T1 - Wireless technologies in factory automation T2 - Factory automation / ed. by Javier Silvestre-Blanes Y1 - 2010 SN - 978-953-7619-42-8 SP - 29 EP - 50 PB - Intech CY - London ER - TY - CHAP A1 - Wollert, Jörg A1 - Plessmann, K. W. T1 - Controlling processes by operating-point based hybride observers T2 - EUFIT '93 : September 7 - 10, 1993, Eurogress Aachen, Germany, proceedings / First European Congress on Fuzzy and Intelligent Technologies Y1 - 1993 SN - 3-86073-176-9 SP - 1151 EP - 1155 PB - Verl. d. Augustinus Buchh. CY - Aachen ER - TY - CHAP A1 - Vedral, Andreas A1 - Wollert, Jörg T1 - Service based Bluetooth dual-hop networks using CORBA T2 - Proceedings of the IASTED International Conference on Artificial Intelligence and Applications : as part of the 23rd IASTED International Multi-Conference on Applied Informatics ; February 14 - 16, 2005, Innsbruck, Austria Y1 - 2005 SN - 0-88986-457-8 SP - 724 EP - 728 PB - Acta Pr. CY - Anaheim, Calif. ER - TY - CHAP A1 - Vedral, Andreas A1 - Wollert, Jörg A1 - Buda, A. A1 - Altrock, R. T1 - The capability of bluetooth for real-time transmission in automation T2 - Proceedings of the IASTED International Conference on Networks and Communication Systems 2006 : March 29 - 31, 2006, Chiang Mai, Thailand Y1 - 2006 SP - 168 EP - 175 PB - Acta Pr. CY - Anaheim, Calif. ER - TY - CHAP A1 - Schürmann, Volker A1 - Buda, Aurel A1 - Jonker, Stefan A1 - Palmhof, Norman A1 - Wollert, Jörg T1 - Wireless in future automotive applications T2 - Mobile and wireless communications network layer and circuit level design / ed. by Salma Ait Fares ... Y1 - 2010 SN - 978-953-307-042-1 SP - 71 EP - 92 PB - Intech CY - London ER - TY - CHAP A1 - Vedral, Andreas A1 - Kruse, Thomas A1 - Wollert, Jörg T1 - Development and performance evaluation of an antenna diversity module for industrial communication based on IEEE 802.15.4 T2 - 12th IEEE International Conference on Emerging Technologies and Factory Automation : ETFA 2007 : proceedings : 25-28 Sept. 2007, Patras, Greece Y1 - 2007 SN - 1424408261 ; 9781424408269 U6 - https://doi.org/10.1109/EFTA.2007.4416769 SP - 177 EP - 186 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Schürmann, Volker A1 - Leidinger, R. A1 - Wollert, Jörg T1 - Simplified rapid-prototyping with automation technology T2 - Automobiles and sustainable mobility : FISITA 2010 World Automotive Congress, 30 May - 4 June, Budapest, Hungary ; proceedings Y1 - 2010 SN - 978-963-9058-29-3 SP - F2010C093 ER - TY - JOUR A1 - Oberländer, Jan A1 - Bromm, Alexander A1 - Wendeler, Luisa A1 - Iken, Heiko A1 - Palomar Duran, Marlena A1 - Greeff, Anton A1 - Kirchner, Patrick A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Towards a biosensor to monitor the sterilisation efficiency of aseptic filling machines JF - Physica status solidi (a) N2 - Sterilisation processes are compulsory in medicine, pharmacy, and food industries to prevent infections of consumers and microbiological contaminations of products. Monitoring the sterilisation by conventional microbiological methods is time- and lab-consuming. To overcome this problem, in this work a novel biosensor has been proposed. The sensor enables a fast method to evaluate sterilisation processes. By means of thin-film technology the sensor's transducer structures in form of IDEs (interdigitated electrodes) have been fabricated on a silicon substrate. Physical characterisation of the developed sensor was done by AFM, SEM, and profilometry. Impedance analyses were conducted for the electrical characterisation. As microbiological layer spores of B. atrophaeus have been immobilised on the sensing structure; spores of this type are a well-known sterilisation test organism. Impedance measurements at a fixed frequency over time were performed to monitor the immobilisation process. A sterilisation process according to aseptic filling machines was applied to demonstrate the sensor functionality. After both, immobilisation and sterilisation, a change in impedance could successfully be detected. Y1 - 2015 U6 - https://doi.org/10.1002/pssa.201431900 SN - 1862-6319 VL - 212 IS - 6 SP - 1299 EP - 1305 PB - Wiley CY - Weinheim ER - TY - JOUR A1 - Jildeh, Zaid B. A1 - Wagner, Torsten A1 - Schöning, Michael Josef A1 - Pieper, Martin T1 - Simulating the electromagnetic‐thermal treatment of thin aluminium layers for adhesion improvement JF - Physica status solidi (a) N2 - A composite layer material used in packaging industry is made from joining layers of different materials using an adhesive. An important processing step in the production of aluminium-containing composites is the surface treatment and consequent coating of adhesive material on the aluminium surface. To increase adhesion strength between aluminium layer and the adhesive material, the foil is heat treated. For efficient heating, induction heating was considered as state-of-the-art treatment process. Due to the complexity of the heating process and the unpredictable nature of the heating source, the control of the process is not yet optimised. In this work, a finite element analysis of the process was established and various process parameters were studied. The process was simplified and modelled in 3D. The numerical model contains an air domain, an aluminium layer and a copper coil fitted with a magnetic field concentrating material. The effect of changing the speed of the aluminium foil (or rolling speed) was studied with the change of the coil current. Statistical analysis was used for generating a general control equation of coil current with changing rolling speed. Y1 - 2015 U6 - https://doi.org/10.1002/pssa.201431893 SN - 1862-6319 VL - Vol. 212 IS - 6 SP - 1234 EP - 1241 PB - Wiley CY - Weinheim ER - TY - JOUR A1 - Pilas, Johanna A1 - Iken, Heiko A1 - Selmer, Thorsten A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Development of a multi‐parameter sensor chip for the simultaneous detection of organic compounds in biogas processes JF - Physica status solidi (a) N2 - An enzyme-based multi-parameter biosensor is developed for monitoring the concentration of formate, d-lactate, and l-lactate in biological samples. The sensor is based on the specific dehydrogenation by an oxidized β-nicotinamide adenine dinucleotide (NAD+)-dependent dehydrogenase (formate dehydrogenase, d-lactic dehydrogenase, and l-lactic dehydrogenase, respectively) in combination with a diaphorase from Clostridium kluyveri (EC 1.8.1.4). The enzymes are immobilized on a platinum working electrode by cross-linking with glutaraldehyde (GA). The principle of the determination scheme in case of l-lactate is as follows: l-lactic dehydrogenase (l-LDH) converts l-lactate into pyruvate by reaction with NAD+. In the presence of hexacyanoferrate(III), the resulting reduced β-nicotinamide adenine dinucleotide (NADH) is then regenerated enzymatically by diaphorase. The electrochemical detection is based on the current generated by oxidation of hexacyanoferrate(II) at an applied potential of +0.3 V vs. an Ag/AgCl reference electrode. The biosensor will be electrochemically characterized in terms of linear working range and sensitivity. Additionally, the successful practical application of the sensor is demonstrated in an extract from maize silage. Y1 - 2015 U6 - https://doi.org/10.1002/pssa.201431894 SN - 1862-6319 VL - 212 IS - 6 SP - 1306 EP - 1312 PB - Wiley CY - Weinheim ER -