TY - JOUR A1 - Kahmann, Stephanie L. A1 - Rausch, Valentin A1 - Plümer, Jonathan A1 - Müller, Lars P. A1 - Pieper, Martin A1 - Wegmann, Kilian T1 - The automized fracture edge detection and generation of three-dimensional fracture probability heat maps JF - Medical Engineering & Physics N2 - With proven impact of statistical fracture analysis on fracture classifications, it is desirable to minimize the manual work and to maximize repeatability of this approach. We address this with an algorithm that reduces the manual effort to segmentation, fragment identification and reduction. The fracture edge detection and heat map generation are performed automatically. With the same input, the algorithm always delivers the same output. The tool transforms one intact template consecutively onto each fractured specimen by linear least square optimization, detects the fragment edges in the template and then superimposes them to generate a fracture probability heat map. We hypothesized that the algorithm runs faster than the manual evaluation and with low (< 5 mm) deviation. We tested the hypothesis in 10 fractured proximal humeri and found that it performs with good accuracy (2.5 mm ± 2.4 mm averaged Euclidean distance) and speed (23 times faster). When applied to a distal humerus, a tibia plateau, and a scaphoid fracture, the run times were low (1–2 min), and the detected edges correct by visual judgement. In the geometrically complex acetabulum, at a run time of 78 min some outliers were considered acceptable. An automatically generated fracture probability heat map based on 50 proximal humerus fractures matches the areas of high risk of fracture reported in medical literature. Such automation of the fracture analysis method is advantageous and could be extended to reduce the manual effort even further. KW - Fracture classification KW - Shoulder KW - Probability distribution mapping KW - Morphing KW - Imaging Y1 - 2022 SN - 1350-4533 VL - 2022 IS - 110 PB - Elsevier CY - Amsterdam ER - TY - THES A1 - Jesse, Judith T1 - Coming to Equal Sex : eine Aufklärungskampagne zur Orgasmuslücke N2 - Die „Orgasmuslücke“ ist ein Begriff aus der Sexualforschung, der die Ungleichheit von Orgasmen zwischen den verschiedenen Geschlechtern und Sexualitäten beschreibt. Sie beruht dabei vor allem auf das problematische Verständnis von Sex, das durch verschiedene kulturelle Einflüsse vermittelt wird. Um über diese Einflüsse aufzuklären, wurde das Format „fuckfulness“ konzipiert. Mithilfe von animierten Videos und darauf aufbauendem Social-Media-Content befasst sich „fuckfulness“ ausführlich mit allen Hintergründen der Orgasmuslücke und gestaltet sexuelle Aufklärung neu. Durch junge und moderne Kommunikation wird das Projekt auch für eine jüngere Zielgruppe unterhaltsam. Ziel ist ein neues Verständnis von Sex, in dem die Bedürfnisse der Frau gleichberechtigt neben denen des Mannes stehen und entsprechende Beachtung finden. So soll die Orgasmuslücke schmaler werden, damit die Gleichstellung endlich auch in den eigenen vier Wänden gelebt werden kann. KW - Kommunikationsdesign KW - Kampagnendesign KW - Konzeption KW - Animation KW - Illustration Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Janssen, Hanna T1 - UMGARNT : Handarbeit als Mittel zur Festigung der emotionalen Bindung zu Möbelstücken N2 - Nach drei Jahren ist der Anblick der beigen Kommode doch etwas langweilig geworden und es steht ein Tapetenwechsel an? Das ist noch lange kein Grund, neue Möbel kaufen zu müssen. Mit dem „BOBBI“-Regal lässt sich das Farbkonzept des Möbelstücks fortlaufend anpassen. Das reduzierte Grundgestell basiert auf einem einfachen Stecksystem und ermöglicht nicht nur einen schnellen, intuitiven Aufbau, sondern auch eine modulare Erweiterung des Regalsystems. Eintönig? Nein Danke! Zeitloses, langlebiges Design muss nicht schlicht und farblos sein! Der Schlüssel liegt in der Individualisierbarkeit. Mithilfe einer einfachen textilen Bespannungstechnik passt der Kunde das Gerüst nach seinen Vorstellungen an. Auf diese Weise kann der Charakter des Möbelstücks nicht nur farblich, sondern auch strukturell regelmäßig verändert werden und trägt zu einer nachhaltigen und achtsamen Raumgestaltung bei. KW - Möbeldesign KW - Textil KW - Individualisierbarkeit KW - Achtsamkeit KW - Weben Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ioannidou, Martha T1 - Master of Procrastination N2 - In den letzten Jahren ist das Thema “Prokrastinieren” omnipräsent geworden. Gegensätzlich dazu versuchen immer mehr Menschen sich zu optimieren. Ziel dieser Arbeit ergibt sich in der Verbindung dieser paradoxen Vorgänge. Im Video wird nicht nur der Begriff Prokrastinieren erklärt, sondern auch ein faktisch basierter Leitfaden zum verbesserten Aufschieben präsentiert. Der Zuschauer kann sich in humoristisch und ironischer Art mit der Thematik auseinandersetzten, Ohne sich mit der negativen Konnotation zu beschäftigen. “Master of Procrastination” eröffnet einen neuen Blickwinkel und informierten Gleichermaßen zu einer unbeliebten Problematik. KW - Prokrastinieren KW - Aufschieben KW - Aufschieberitis KW - Machichmorgen KW - Leitfaden Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Inceman Cremer, Suzan T1 - Kouyou : Ort im Raum N2 - Selbstliebe, der Moment der Ruhe, sich eine mentale Pause erlauben und von allem bewusst abzuschalten, sind aktuelle Themen unserer Gesellschaft. Die Zeit, in der wir leben, bewegt sich in einer Geschwindigkeit, die alle unsere Sinne überlastet und uns nicht mehr erlaubt, selbst zuzuhören oder volle Momente der Ruhe zu erleben. Thema der Bachelorarbeit ist der Entwurf eines Sitzmöbels, welches inspiriert ist durch die sakralische Architektur. Der Stuhl soll das Gefühl von Umformung und Leichtigkeit vermitteln. Er ist aus Eiche gebaut und unterstützt den Menschen in seiner bewussten Sitzhaltung. Die Eiche ist ein Baum, der für Kraft, Durchhaltevermögen und Gerechtigkeit steht. Es heißt auch, wenn man eine Eiche sieht, sie umarmen soll, da sie heilende Kräfte hat. Hier ist aber die Eiche, die den Menschen symbolisch umarmen soll, wenn man auf ihr sitzt. Und somit spielen Architektur, Möbel und der Mensch eine spielende Rolle, und zwar ist es die menschliche Haltung im Raum. KW - Philosophie KW - Architektur KW - Möbel KW - Reise KW - Eiche Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Ihl, Andrea T1 - Sehen und gesehen werden: Eine Darstellung (post-)migrantischer Perspektiven N2 - In einer Welt, definiert durch Grenzziehungen, ist es vor allem für diejenigen schwer, ihren Platz zu finden, die bereits über diese hinauswachsen mussten. Denn Migration bedeutet nicht nur, eine Strecke über eine ländliche Linie hinter sich zu bringen. Oft werden die komplexen emotionalen Facetten dieser permanenten Überquerung vergessen, die über Generationen ihre Spuren hinterlassen. Was bedeutet es, ein Leben ganz von neu aufbauen zu müssen, wenn man bereits eins hinter sich gelassen hat? Wieso verspüren wir Sehnsucht nach einer Heimat, die es so gar nicht geben kann? Und wann haben wir das Gefühl, endlich angekommen zu sein? Über diese und viele weitere Fragen wird in »Mesta« zusammen mit (Post-)Migrant:innen reflektiert, die intensiv ihre Erfahrungen teilen. Ziel der Publikation ist das, was meistens vernachlässigt wird: einfach zuzuhören. KW - Illustration KW - Editorialdesign KW - Interview KW - Print KW - Postmigrantisch Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - PAT A1 - Hüning, Felix A1 - Backes, Andreas T1 - Wiegand-Modul N2 - Ein Wiegand-Modul (110;210;310) umfassend- eine Sensorspule (112;212;312),- einen ersten Wiegand-Draht (116a;216a;316a), der zumindest teilweise innerhalb der Sensorspule (112;212;312) angeordnet ist, und- einen zweiten Wiegand-Draht (116b;216b;316b), der zumindest teilweise innerhalb der Sensorspule (112;212;312) angeordnet ist und sich im Wesentlichen parallel zu dem ersten Wiegand-Draht (116a;216a;316a) erstreckt, ist bekannt.Um eine effiziente Ausnutzung der durch die Ummagnetisierung der Wiegand-Drähte (116a,116b;216a,216b;316a,316b) in die Sensorspule (112;212;312) induzierten elektrischen Energie zu ermöglichen, sind der erste Wiegand-Draht (116a;216a;316a) und der zweite Wiegand-Draht (116b;216b;316b) bezogen auf eine axiale Richtung der Sensorspule (112;212;312) versetzt zueinander angeordnet. Y1 - 2023 N1 - Patent DE102021115745B3 2022.07.21 ER - TY - THES A1 - Horvath, Nicolas T1 - Neues Corporate Design für das Rautenstrauch Joest Museum Köln N2 - Der Mensch in seinen Welten – das Konzept des Rautenstrauch Joest Museums verfolgt den Ansatz des Kulturvergleichs und strebt im Zuge dessen die Betonung der Ebenbürtigkeit aller Kulturen an. Die Sammlung unterteilt sich nicht – wie gewohnt – anhand geografischer Gesichtspunkte, sondern behandelt Themen, die Menschen auf der ganzen Welt beschäftigen. Das in dieser Arbeit gestaltete neue Erscheinungsbild greift den veränderten gesellschaftlichen Stellenwert von ethnologischen Museen auf und positioniert das Museum als aktiven Diskussionsteilnehmer im Zuge des Postkolonialismus. Das entwickelte Key-Visual aus eigener Schrift, einheitlicher Rastersystematik und prägnantem Farbkonzept gibt einen Einblick darin, wie Menschen früher probiert haben, ihre Welt zu verstehen und sie zu erschließen. KW - Markengestaltung KW - Museum KW - Redesign KW - Postkolonialismus KW - Kunst Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Horikawa, Atsushi A1 - Ashikaga, Mitsugu A1 - Yamaguchi, Masato A1 - Ogino, Tomoyuki A1 - Aoki, Shigeki A1 - Wirsum, Manfred A1 - Funke, Harald A1 - Kusterer, Karsten T1 - Combined heat and power supply demonstration of Micro-Mix Hydrogen Combustion Applied to M1A-17 Gas Turbine T2 - Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A) N2 - Kawasaki Heavy Industries, Ltd. (KHI), Aachen University of Applied Sciences, and B&B-AGEMA GmbH have investigated the potential of low NOx micro-mix (MMX) hydrogen combustion and its application to an industrial gas turbine combustor. Engine demonstration tests of a MMX combustor for the M1A-17 gas turbine with a co-generation system were conducted in the hydrogen-fueled power generation plant in Kobe City, Japan. This paper presents the results of the commissioning test and the combined heat and power (CHP) supply demonstration. In the commissioning test, grid interconnection, loading tests and load cut-off tests were successfully conducted. All measurement results satisfied the Japanese environmental regulation values. Dust and soot as well as SOx were not detected. The NOx emissions were below 84 ppmv at 15 % O2. The noise level at the site boundary was below 60 dB. The vibration at the site boundary was below 45 dB. During the combined heat and power supply demonstration, heat and power were supplied to neighboring public facilities with the MMX combustion technology and 100 % hydrogen fuel. The electric power output reached 1800 kW at which the NOx emissions were 72 ppmv at 15 % O2, and 60 %RH. Combustion instabilities were not observed. The gas turbine efficiency was improved by about 1 % compared to a non-premixed type combustor with water injection as NOx reduction method. During a total equivalent operation time of 1040 hours, all combustor parts, the M1A-17 gas turbine as such, and the co-generation system were without any issues. KW - industrial gas turbine KW - combustor development KW - fuels KW - hydrogen KW - emission Y1 - 2022 SN - 978-0-7918-8599-4 U6 - http://dx.doi.org/10.1115/GT2022-81620 N1 - ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition June 13–17, 2022 Rotterdam, Netherlands PB - American Society of Mechanical Engineers CY - Fairfield ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Rau, Christoph A1 - Sattler, Johannes, Christoph A1 - Anthrakidis, Anette A1 - Teixeira Boura, Cristiano José A1 - O’Connor, B. A1 - Chico Caminos, R.A. A1 - Rendón, C. A1 - Hilger, P. T1 - Concentrating solar power T2 - Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications N2 - The focus of this chapter is the production of power and the use of the heat produced from concentrated solar thermal power (CSP) systems. The chapter starts with the general theoretical principles of concentrating systems including the description of the concentration ratio, the energy and mass balance. The power conversion systems is the main part where solar-only operation and the increase in operational hours. Solar-only operation include the use of steam turbines, gas turbines, organic Rankine cycles and solar dishes. The operational hours can be increased with hybridization and with storage. Another important topic is the cogeneration where solar cooling, desalination and of heat usage is described. Many examples of commercial CSP power plants as well as research facilities from the past as well as current installed and in operation are described in detail. The chapter closes with economic and environmental aspects and with the future potential of the development of CSP around the world. KW - Central receiver power plant KW - Concentrated systems KW - Gas turbine KW - Hybridization KW - Power conversion systems Y1 - 2022 SN - 978-0-12-819734-9 SP - 670 EP - 724 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Hoffschmidt, Bernhard A1 - Alexopoulos, Spiros A1 - Göttsche, Joachim A1 - Sauerborn, Markus A1 - Kaufhold, O. T1 - High Concentration Solar Collectors T2 - Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications N2 - Solar thermal concentrated power is an emerging technology that provides clean electricity for the growing energy market. To the solar thermal concentrated power plant systems belong the parabolic trough, the Fresnel collector, the solar dish, and the central receiver system. For high-concentration solar collector systems, optical and thermal analysis is essential. There exist a number of measurement techniques and systems for the optical and thermal characterization of the efficiency of solar thermal concentrated systems. For each system, structure, components, and specific characteristics types are described. The chapter presents additionally an outline for the calculation of system performance and operation and maintenance topics. One main focus is set to the models of components and their construction details as well as different types on the market. In the later part of this article, different criteria for the choice of technology are analyzed in detail. KW - Central receiver system KW - Concentrated solar collector KW - Solar dish KW - Solar concentration Y1 - 2022 SN - 978-0-12-819734-9 U6 - http://dx.doi.org/10.1016/B978-0-12-819727-1.00058-3 SP - 198 EP - 245 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Hoffmann, Andreas A1 - Uhl, Matthias A1 - Ceblin, Maximilian A1 - Rohrbach, Felix A1 - Bansmann, Joachim A1 - Mallah, Marcel A1 - Heuermann, Holger A1 - Jacob, Timo A1 - Kuehne, Alexander J.C. T1 - Atmospheric pressure plasma-jet treatment of PAN-nonwovens—carbonization of nanofiber electrodes JF - C - Journal of Carbon Research N2 - Carbon nanofibers are produced from dielectric polymer precursors such as polyacrylonitrile (PAN). Carbonized nanofiber nonwovens show high surface area and good electrical conductivity, rendering these fiber materials interesting for application as electrodes in batteries, fuel cells, and supercapacitors. However, thermal processing is slow and costly, which is why new processing techniques have been explored for carbon fiber tows. Alternatives for the conversion of PAN-precursors into carbon fiber nonwovens are scarce. Here, we utilize an atmospheric pressure plasma jet to conduct carbonization of stabilized PAN nanofiber nonwovens. We explore the influence of various processing parameters on the conductivity and degree of carbonization of the converted nanofiber material. The precursor fibers are converted by plasma-jet treatment to carbon fiber nonwovens within seconds, by which they develop a rough surface making subsequent surface activation processes obsolete. The resulting carbon nanofiber nonwovens are applied as supercapacitor electrodes and examined by cyclic voltammetry and impedance spectroscopy. Nonwovens that are carbonized within 60 s show capacitances of up to 5 F g⁻¹. Y1 - 2022 U6 - http://dx.doi.org/10.3390/c8030033 SN - 2311-5629 N1 - This article belongs to the Collection "Nanoporous Carbon Materials for Advanced Technological Applications" VL - 8 IS - 3 PB - MDPI CY - Basel ER - TY - JOUR A1 - Hoffmann, Andreas A1 - Rohrbach, Felix A1 - Uhl, Matthias A1 - Ceblin, Maximilian A1 - Bauer, Thomas A1 - Mallah, Marcel A1 - Jacob, Timo A1 - Heuermann, Holger A1 - Kuehne, Alexander J. C. T1 - Atmospheric pressure plasma-jet treatment of polyacrylonitrile-nonwovens—Stabilization and roll-to-roll processing JF - Journal of Applied Polymer Science N2 - Carbon nanofiber nonwovens represent a powerful class of materials with prospective application in filtration technology or as electrodes with high surface area in batteries, fuel cells, and supercapacitors. While new precursor-to-carbon conversion processes have been explored to overcome productivity restrictions for carbon fiber tows, alternatives for the two-step thermal conversion of polyacrylonitrile precursors into carbon fiber nonwovens are absent. In this work, we develop a continuous roll-to-roll stabilization process using an atmospheric pressure microwave plasma jet. We explore the influence of various plasma-jet parameters on the morphology of the nonwoven and compare the stabilized nonwoven to thermally stabilized samples using scanning electron microscopy, differential scanning calorimetry, and infrared spectroscopy. We show that stabilization with a non-equilibrium plasma-jet can be twice as productive as the conventional thermal stabilization in a convection furnace, while producing electrodes of comparable electrochemical performance. KW - batteries and fuel cells KW - electrospinning KW - fibers KW - irradiation KW - porous materials Y1 - 2022 U6 - http://dx.doi.org/10.1002/app.52887 SN - 0021-8995 (Print) SN - 1097-4628 (Online) N1 - Weitere Informationen: Bundesministerium für Bildung und Forschung, Fördernummer: 13XP5036E. Deutsche Forschungsgemeinschaft, Fördernummern: 390874152, 441209207, 327886311 VL - 139 IS - 37 SP - 1 EP - 9 PB - Wiley ER - TY - CHAP A1 - Hinke, Christian A1 - Vervier, Luisa A1 - Brauner, Philipp A1 - Schneider, Sebastian A1 - Steuer-Dankert, Linda A1 - Ziefle, Martina A1 - Leicht-Scholten, Carmen T1 - Capability configuration in next generation manufacturing T2 - Forecasting next generation manufacturing : digital shadows, human-machine collaboration, and data-driven business models N2 - Industrial production systems are facing radical change in multiple dimensions. This change is caused by technological developments and the digital transformation of production, as well as the call for political and social change to facilitate a transformation toward sustainability. These changes affect both the capabilities of production systems and companies and the design of higher education and educational programs. Given the high uncertainty in the likelihood of occurrence and the technical, economic, and societal impacts of these concepts, we conducted a technology foresight study, in the form of a real-time Delphi analysis, to derive reliable future scenarios featuring the next generation of manufacturing systems. This chapter presents the capabilities dimension and describes each projection in detail, offering current case study examples and discussing related research, as well as implications for policy makers and firms. Specifically, we discuss the benefits of capturing expert knowledge and making it accessible to newcomers, especially in highly specialized industries. The experts argue that in order to cope with the challenges and circumstances of today’s world, students must already during their education at university learn how to work with AI and other technologies. This means that study programs must change and that universities must adapt their structural aspects to meet the needs of the students. Y1 - 2022 SN - 978-3-031-07733-3 U6 - http://dx.doi.org/10.1007/978-3-031-07734-0_6 SP - 95 EP - 106 PB - Springer CY - Cham ER - TY - JOUR A1 - Heuermann, Holger A1 - Emmrich, Thomas A1 - Bongartz, Simon T1 - Microwave spark plug to support ignitions with high compression ratios JF - IEEE Transactions on Plasma Science N2 - Upcoming gasoline engines should run with a larger number of fuels beginning from petrol over methanol up to gas by a wide range of compression ratios and a homogeneous charge. In this article, the microwave (MW) spark plug, based on a high-speed frequency hopping system, is introduced as a solution, which can support a nitrogen compression ratio up to 1:39 in a chamber and more. First, an overview of the high-speed frequency hopping MW ignition and operation system as well as the large number of applications are presented. Both gives an understanding of this new base technology for MW plasma generation. Focus of the theoretical part is the explanation of the internal construction of the spark plug, on the achievable of the high voltage generation as well as the high efficiency to hold the plasma. In detail, the development process starting with circuit simulations and ending with the numerical multiphysics field simulations is described. The concept is evaluated with a reference prototype covering the frequency range between 2.40 and 2.48 GHz and working over a large power range from 20 to 200 W. A larger number of different measurements starting by vector hot-S11 measurements and ending by combined working scenarios out of hot temperature, high pressure and charge motion are winding up the article. The limits for the successful pressure tests were given by the pressure chamber. Pressures ranged from 1 to 39 bar and charge motion up to 25 m/s as well as temperatures from 30◦ to 125◦. KW - Automotive application KW - ignition KW - microplasma KW - microwave (MW) plasma KW - plasma jet Y1 - 2022 U6 - http://dx.doi.org/10.1109/TPS.2022.3183690 SN - 1939-9375 IS - Early Access SP - 1 EP - 6 PB - IEEE ER - TY - THES A1 - Herzog, Nathalie T1 - Willkommen, heimische Wildtiere! : eine Kampagne zum Thema Artenschutz N2 - Tierpatenschaften bilden einen notwendigen Bestandteil, um Gelder für den Artenschutz zu akquirieren und sowohl in Tierschutzprojekte als auch in die Erhaltung der Lebensräume zu investieren. Doch um weiterhin Pat:Innen zu gewinnen und die Spendenbereitschaft zu steigern, müssen Patenschaften persönlicher werden. Dafür schafft dieses Projekt eine neue Form der Patenschaft, die in einer vorwiegend digitalen Kampagne beworben wird. Mithilfe von Kooperationen über Instagram gewinnt das Thema an Reichweite. Unter dem Motto "ganz nah dran“ überwindet die Kampagne die physische Distanz zwischen Wildtier und Pat:In durch virtuelle Erlebnisse und schafft somit eine emotionale Verbindung. Dadurch steigt nicht die Spendenbereitschaft für das Patentier an sich, sondern ihm zuliebe eben auch für den Schutz des Lebensraums. Damit öffnet dieses Konzept den Blick für unkonventionelle Lösungen zum Erhalt der Wildtiere in Deutschland. KW - Wildtiere KW - Tierpatenschaft KW - Deutschland KW - emotionale Verbindung KW - Spendenbereitschaft Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Herssens, Nolan A1 - Cowburn, James A1 - Albracht, Kirsten A1 - Braunstein, Bjoern A1 - Cazzola, Dario A1 - Colyer, Steffi A1 - Minetti, Alberto E. A1 - Pavei, Gaspare A1 - Rittweger, Jörn A1 - Weber, Tobias A1 - Green, David A. ED - Cattaneo, Luigi T1 - Movement in low gravity environments (MoLo) programme – the MoLo-L.O.O.P. study protocol JF - PLOS ONE / Public Library of Science N2 - Exposure to prolonged periods in microgravity is associated with deconditioning of the musculoskeletal system due to chronic changes in mechanical stimulation. Given astronauts will operate on the Lunar surface for extended periods of time, it is critical to quantify both external (e.g., ground reaction forces) and internal (e.g., joint reaction forces) loads of relevant movements performed during Lunar missions. Such knowledge is key to predict musculoskeletal deconditioning and determine appropriate exercise countermeasures associated with extended exposure to hypogravity. Y1 - 2022 U6 - http://dx.doi.org/10.1371/journal.pone.0278051 SN - 1932-6203 VL - 17 IS - 11 PB - Plos CY - San Francisco ER - TY - THES A1 - Hemmers, Marie Jane T1 - Modularität im Caravaning : Entwurf eines modularen Interior-Systems für die Anwendung in mobilen Reisewägen. N2 - Die Arbeit „Modularität im Caravaning“ befasst sich mit der konzeptionellen und gestalterischen Ausarbeitung eines Interior-Systems nach dem Vorbild modularer Bauweise für die Anwendung in mobilen Reisewägen. Das Projekt steht im Kontext einer Diskrepanz zwischen den unflexiblen Ausstattungen gängiger Reisewägen und den Nutzeranforderungen nach einer anpassungsfähigen Einrichtung. Die Lebenszeit eines Wohnwagens liegt im Durchschnitt zwischen 25-30 Jahren. In dieser Zeitspanne durchlaufen die Nutzer unterschiedliche Lebensphasen, aus denen sich neue Nutzungsszenarien ergeben können. Die festverklebten und verschraubten Einrichtungen bestehender Caravankonzepte stehen einer flexiblen Umgestaltung des Innenraumes nach den Bedürfnissen der Nutzer jedoch entgegen und erschweren darüber hinaus Reparaturen und das Recycling am Produktlebensende. Die Covid-19 Pandemie hat den Caravan-Trend weiterhin verstärkt. Die Digitalisierung und eine ortsungebundene Arbeit schafft neue Nutzungsszenarien in dem der Caravan als Office-Camper zum Einsatz kommt. Das Interior-system „CAMO“ ermöglicht es Nutzern Veränderungen des Innenraumes vorzunehmen, indem Modulkörper gemäß einer Rasterung in dem Innenraum an Boden- und Wandschienen flexibel angeordnet und befestigt werden können. Die Nutzer gewinnen mehr Autonomie in der Mitgestaltung des Umfeldes, indem er das Interior nach seinen Bedürfnissen anpassen kann. Die trennbaren Modulbaukörper aus recycelfähigen Materialien ermöglichen überdies eine verbesserte Reparierbarkeit und erleichtern die Zurückführung in den Stoffkreislauf am Produktlebensende. Das modulare Interior-System „CAMO“ beantwortet das Bedürfnis nach einer flexiblen Inneneinrichtung, die sich an die wandelnden Nutzungsszenarien anpasst. KW - Caravaning KW - Modular KW - Interior-System,Reisewagen KW - Inneneinrichtung KW - Work-life-blending Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Heining, Theresa Marie T1 - Das Museum Küppersmühle : Entwicklung eines neuen Erscheinungsbildes und Orientierungssystems für das Museum N2 - Der Raum des Museums ist kein funktionaler Ort. Er dient den Besucher:innen als Inspiration, gefüllt mit Kunst, Poesie und Konzept. Das Museum Küppersmühle ist dabei eine klassische White Cube Gallery mit weitläufigen Räumen, viel Platz für die Kunst und einer hochwertigen Sammlung. Es befindet sich in einem umgebauten, alten Speichergebäude im Duisburger Innenhafen. Im Zuge der Masterarbeit wurden ein Erscheinungsbild und Orientierungssystem für das Museums entwickelt. Das Gestaltungssystem ist ein Spiel von Verbindungen, die mal gradlinig, teilweise geschwungen und manchmal verdreht sind. Der geschwungene Pfeil wird hierbei zum Visual des Umwegs, des Gedankensprungs und des Entdeckens. Es ist ein Informationskonzept entstanden, das dazu einlädt, über die geführten Wege hinauszublicken. Es leitet digital und mittels verschiedener Printmedien durch die Ausstellung für moderne Kunst. KW - Erscheinungsbild KW - Orientierungssystem KW - Museum KW - Leitsystem KW - Architektur Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Hein, Andreas M. A1 - Eubanks, T. Marshall A1 - Lingam, Manasvi A1 - Hibberd, Adam A1 - Fries, Dan A1 - Schneider, Jean A1 - Kervella, Pierre A1 - Kennedy, Robert A1 - Perakis, Nikolaos A1 - Dachwald, Bernd T1 - Interstellar now! Missions to explore nearby interstellar objects JF - Advances in Space Research N2 - The recently discovered first hyperbolic objects passing through the Solar System, 1I/’Oumuamua and 2I/Borisov, have raised the question about near term missions to Interstellar Objects. In situ spacecraft exploration of these objects will allow the direct determination of both their structure and their chemical and isotopic composition, enabling an entirely new way of studying small bodies from outside our solar system. In this paper, we map various Interstellar Object classes to mission types, demonstrating that missions to a range of Interstellar Object classes are feasible, using existing or near-term technology. We describe flyby, rendezvous and sample return missions to interstellar objects, showing various ways to explore these bodies characterizing their surface, dynamics, structure and composition. Their direct exploration will constrain their formation and history, situating them within the dynamical and chemical evolution of the Galaxy. These mission types also provide the opportunity to explore solar system bodies and perform measurements in the far outer solar system. KW - Interstellar objects KW - Trajectories KW - Missions Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.asr.2021.06.052 SN - 0273-1177 VL - 69 IS - 1 SP - 402 EP - 414 PB - Elsevier CY - Amsterdam ER -