TY - JOUR A1 - Claer, Mario A1 - Ferrein, Alexander A1 - Schiffer, Stefan T1 - Calibration of a Rotating or Revolving Platform with a LiDAR Sensor JF - Applied Sciences Y1 - 2019 U6 - http://dx.doi.org/10.3390/app9112238 SN - 2076-3417 VL - Volume 9 IS - issue 11, 2238 PB - MDPI CY - Basel ER - TY - JOUR A1 - Heuermann, Holger A1 - Schiek, Burkhard T1 - Calibration of network analyser measurements with leakage errors JF - Electronics letters. 30 (1994), H. 1 Y1 - 1994 SN - 0013-5194 SP - 52 EP - 53 ER - TY - JOUR A1 - Heuermann, Holger T1 - Calibration procedures with series impedances and unknown lines simplify on-wafer measurements JF - IEEE transactions on microwave theory and techniques : MTT ; a publication of the IEEE Microwave Theory and Techniques Society. 47 (1999), H. 1 Y1 - 1999 SN - 0018-9480 SP - 1 EP - 5 ER - TY - JOUR A1 - Schopp, Christoph A1 - Doll, Timo A1 - Gräser, Ulrich A1 - Harzheim, Thomas A1 - Heuermann, Holger A1 - Kling, Rainer A1 - Marso, Michael T1 - Capacitively Coupled High-Pressure Lamp Using Coaxial Line Networks JF - IEEE Transactions on Microwave Theory and Techniques N2 - This paper describes the development of a capacitively coupled high-pressure lamp with input power between 20 and 43 W at 2.45 GHz, using a coaxial line network. Compared with other electrodeless lamp systems, no cavity has to be used and a reduction in the input power is achieved. Therefore, this lamp is an alternative to the halogen incandescent lamp for domestic lighting. To serve the demands of domestic lighting, the filling of the lamp is optimized over all other resulting requirements, such as high efficacy at low induced powers and fast startups. A workflow to develop RF-driven plasma applications is presented, which makes use of the hot S-parameter technique. Descriptions of the fitting process inside a circuit and FEM simulator are given. Results of the combined ignition and operation network from simulations and measurements are compared. An initial prototype is built and measurements of the lamp's lighting properties are presented along with an investigation of the efficacy optimizations using large signal amplitude modulation. With this lamp, an efficacy of 135 lmW -1 is achieved. Y1 - 2016 U6 - http://dx.doi.org/10.1109/TMTT.2016.2600326 SN - 0018-9480 VL - 64 IS - 10 SP - 3363 EP - 3368 PB - IEEE CY - New York, NY ER - TY - JOUR A1 - Hagemann, Hans-Jürgen A1 - Hennings, D. A1 - Wernicke, R. T1 - Ceramic multilayer capacitors. Hagemann, H. J.; Hennings, D.; Wernicke, R. JF - Philips' technical review / Philips' Gloeilampenfabrieken. Philips' Gloeilampenfabrieken . 41 (1984) Y1 - 1984 SN - 0031-7926 SP - 89 EP - 98 ER - TY - JOUR A1 - Haag, S. A1 - Zontar, D. A1 - Schleupen, Josef A1 - Müller, T. A1 - Brecher, C. T1 - Chain of refined perception in self-optimizing assembly of micro-optical systems JF - Journal of sensors and sensor systems N2 - Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements – especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base. Y1 - 2014 U6 - http://dx.doi.org/10.5194/jsss-3-87-2014 SN - 2194-878X VL - 3 IS - 1 SP - 87 EP - 95 PB - Copernicus Publ. CY - Göttingen ER - TY - JOUR A1 - Serror, Martin A1 - Hack, Sacha A1 - Henze, Martin A1 - Schuba, Marko A1 - Wehrle, Klaus T1 - Challenges and Opportunities in Securing the Industrial Internet of Things JF - IEEE Transactions on Industrial Informatics Y1 - 2021 U6 - http://dx.doi.org/10.1109/TII.2020.3023507 SN - 1941-0050 VL - 17 IS - 5 SP - 2985 EP - 2996 PB - IEEE CY - New York ER - TY - JOUR A1 - Scholl, Ingrid A1 - Aach, Til A1 - Deserno, Thomas M. A1 - Kuhlen, Torsten T1 - Challenges of medical image processing JF - Computer Science - Research and Development Y1 - 2011 SN - 1865-2042 VL - 26 IS - 1-2 SP - 5 EP - 13 PB - Springer CY - Berlin ER - TY - JOUR A1 - Holtrup, S. A1 - Sadeghfam, Arash A1 - Heuermann, Holger A1 - Awakowicz, P. T1 - Characterization and optimization technique for microwave-driven high-intensity discharge lamps using hot S-parameters JF - IEEE transactions on microwave theories and techniques N2 - High-intensity discharge lamps can be driven by radio-frequency signals in the ISM frequency band at 2.45 GHz, using a matching network to transform the impedance of the plasma to the source impedance. To achieve an optimal operating condition, a good characterization of the lamp in terms of radio frequency equivalent circuits under operating conditions is necessary, enabling the design of an efficient matching network. This paper presents the characterization technique for such lamps and presents the design of the required matching network. For the characterization, a high-intensity discharge lamp was driven by a monofrequent large signal at 2.45 GHz, whereas a frequency sweep over 300 MHz was performed across this signal to measure so-called small-signal hot S-parameters using a vector network analyzer. These parameters are then used as an equivalent load in a circuit simulator to design an appropriate matching network. Using the measured data as a black-box model in the simulation results in a quick and efficient method to simulate and design efficient matching networks in spite of the complex plasma behavior. Furthermore, photometric analysis of high-intensity discharge lamps are carried out, comparing microwave operation to conventional operation. Y1 - 2014 U6 - http://dx.doi.org/10.1109/TMTT.2014.2342652 SN - 0018-9480 VL - 62 IS - 10 SP - 2471 EP - 2480 PB - IEEE CY - New York ER - TY - JOUR A1 - Prume, Klaus A1 - Tyholdt, F. A1 - Calame, F. A1 - Raeder, H. T1 - Chemically derived seeding layer for {100}-textured PZT thin films / Tyholdt, F. ; Calame, F. ; Prume, K. ; Raeder, H. ; Muralt, P. JF - Journal of Electroceramics. 19 (2007), H. 4 Y1 - 2007 SN - 1385-3449 SP - 311 EP - 314 ER - TY - JOUR A1 - Siepmann, Thomas A1 - Rupietta, D. T1 - Closer to the customer with computerized product support JF - Technische Mitteilungen Krupp (1993) Y1 - 1993 CY - Essen ER - TY - JOUR A1 - Hartung, Frank A1 - Horn, U. T1 - Codierung digitaler Videosignale nach dem MPEG-Standard / Hartung, F. ; Horn, U. JF - Mikroelektronik + Mikrosystemtechnik. 9 (1995) Y1 - 1995 N1 - gedruckte Ausgabe in der Bereichsbibliothek Jülich vorhanden SP - 18 EP - 23 ER - TY - JOUR A1 - Hagemann, Hans-Jürgen A1 - Backhaus, U. A1 - Goessner, S. T1 - Collaborative eLearning Concepts for University Level Online Laboratory Courses in Engineering. U. Backhaus, S. Goessner, H. J. Hagemann JF - Proceedings Online Educa Berlin: 8th International Conference on Technology Supported Learning & Training. 2002 Y1 - 2002 N1 - Online Educa <2002, Berlin> SP - 62 EP - 66 ER - TY - JOUR A1 - Schubert, Nicole A1 - Scholl, Ingrid T1 - Comparing GPU-based multi-volume ray casting techniques JF - Computer Science - Research and Development Y1 - 2011 SN - 1865-2042 VL - 26 IS - 12 SP - 39 EP - 50 PB - Springer CY - Berlin ER - TY - JOUR A1 - Ferrein, Alexander A1 - Hermanns, Lutz A1 - Lakemeyer, Gerhard T1 - Comparing Sensor Fusion Techniques for Ball Position Estimation / Ferrein, Alexander ; Hermanns, Lutz ; Lakemeyer, Gerhard JF - RoboCup 2005: Robot Soccer World Cup IX Y1 - 2006 SN - 978-3-540-35437-6 N1 - Lecture Notes in Computer Science ; 4020 SP - 154 EP - 165 PB - Springer CY - Berlin ER - TY - JOUR A1 - Prume, Klaus A1 - Roelofs, Andreas A1 - Schmitz, Thorsten A1 - Reichenberg, Bernd T1 - Compensation of the Parasitic Capacitance of a Scanning Force Microscope Cantilever Used for Measurements on Ferroelectric Capacitors of Submicron Size by Means of Finite Element Simulations / Prume, Klaus ; Roelofs, Andreas ; Schmitz, Thorsten ; Reichenb JF - Japanese Journal of Applied Physics. 41 (2002), H. 11B Y1 - 2002 SN - 0021-4922 SP - 7198 EP - 7201 ER - TY - JOUR A1 - Hüning, Felix A1 - Eifert, T. A1 - Handrick, K. A1 - Neuhausen, U. T1 - Computational Magnetochemistry: Complementary Quantum Mechanical Tools / Eifert, T. ; Handrick, K. ; Hüning, F. ; Neuhausen, U. ; Schilder, H. ; Lueken, H. JF - Zeitschrift für Anorganische und Allgemeine Chemie (ZAAC) - Journal of Inorganic and General Chemistry . 632 (2006), H. 4 Y1 - 2006 SN - 1521-3749 SP - 521 EP - 529 PB - - ER - TY - JOUR A1 - Hüning, Felix A1 - Eifert, T. A1 - Handrick, K. A1 - Neuhausen, U. T1 - Computational Magnetochemistry: Complementary Quantum Mechanical Tools / Eifert, T. ; Handrick, K. ; Hüning, F. ; Neuhausen, U. ; Schilder, H. ; Lueken, H. JF - 20 Jahre Wilhelm-Klemm-Stiftung / Kuratorium der Wilhelm-Klemm-Stiftung (Hrsg.) Y1 - 2006 SN - 978-3-8322-5520-6 SP - 193ff PB - Shaker CY - Aachen ER - TY - JOUR A1 - Wolf, Martin A1 - Luczak, Holger T1 - Computer Supported Communication and Cooperation – Making Information Aware / Luczak, H. ; Wolf, M. JF - Human-computer interaction : proceedings of HCI International '99 (the 8th International Conference on Human-Computer Interaction), Munich, Germany, August 22 - 26, 1999 Y1 - 1999 N1 - HCI - International Conference on Human-Computer Interaction ; 8 (Munich, Germany) : 1999.08.22-26 ; in 2 Bänden SP - 298 EP - 302 PB - Erlbaum CY - Mahwah, NJ ER - TY - JOUR A1 - Wolf, Martin A1 - Simon, S. A1 - Schlick, Christopher T1 - Computergestützte Kooperation - Eine Seifenblase? / Wolf, M.; Simon, S.; Schlick, C. JF - Rechnergestützte Kooperation in Verwaltungen und großen Unternehmen : Tagungsband zum Workshop der GI-Gachgruppe / Peter Mambrey ... ( Hrsg.) Y1 - 1997 SP - 220 EP - 234 PB - Univ., Fachbereich Mathematik u. Informatik CY - Essen ER -