TY  - JOUR
A1  - Holtrup, S.
A1  - Sadeghfam, Arash
A1  - Heuermann, Holger
A1  - Awakowicz, P.
T1  - Characterization and optimization technique for microwave-driven high-intensity discharge lamps using hot S-parameters
JF  - IEEE transactions on microwave theories and techniques
N2  - High-intensity discharge lamps can be driven by radio-frequency signals in the ISM frequency band at 2.45 GHz, using a matching network to transform the impedance of the plasma to the source impedance. To achieve an optimal operating condition, a good characterization of the lamp in terms of radio frequency equivalent circuits under operating conditions is necessary, enabling the design of an efficient matching network. This paper presents the characterization technique for such lamps and presents the design of the required matching network. For the characterization, a high-intensity discharge lamp was driven by a monofrequent large signal at 2.45 GHz, whereas a frequency sweep over 300 MHz was performed across this signal to measure so-called small-signal hot S-parameters using a vector network analyzer. These parameters are then used as an equivalent load in a circuit simulator to design an appropriate matching network. Using the measured data as a black-box model in the simulation results in a quick and efficient method to simulate and design efficient matching networks in spite of the complex plasma behavior. Furthermore, photometric analysis of high-intensity discharge lamps are carried out, comparing microwave operation to conventional operation.
Y1  - 2014
U6  - http://dx.doi.org/10.1109/TMTT.2014.2342652
SN  - 0018-9480
VL  - 62
IS  - 10
SP  - 2471
EP  - 2480
PB  - IEEE
CY  - New York
ER  - 
TY  - JOUR
A1  - Scholl, Ingrid
A1  - Aach, Til
A1  - Deserno, Thomas M.
A1  - Kuhlen, Torsten
T1  - Challenges of medical image processing
JF  - Computer Science - Research and Development
Y1  - 2011
SN  - 1865-2042
VL  - 26
IS  - 1-2
SP  - 5
EP  - 13
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Serror, Martin
A1  - Hack, Sacha
A1  - Henze, Martin
A1  - Schuba, Marko
A1  - Wehrle, Klaus
T1  - Challenges and Opportunities in Securing the Industrial Internet of Things
JF  - IEEE Transactions on Industrial Informatics
Y1  - 2021
U6  - http://dx.doi.org/10.1109/TII.2020.3023507
SN  - 1941-0050
VL  - 17
IS  - 5
SP  - 2985
EP  - 2996
PB  - IEEE
CY  - New York
ER  - 
TY  - JOUR
A1  - Haag, S.
A1  - Zontar, D.
A1  - Schleupen, Josef
A1  - Müller, T.
A1  - Brecher, C.
T1  - Chain of refined perception in self-optimizing assembly of micro-optical systems
JF  - Journal of sensors and sensor systems
N2  - Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements – especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base.
Y1  - 2014
U6  - http://dx.doi.org/10.5194/jsss-3-87-2014
SN  - 2194-878X
VL  - 3
IS  - 1
SP  - 87
EP  - 95
PB  - Copernicus Publ.
CY  - Göttingen
ER  - 
TY  - JOUR
A1  - Hagemann, Hans-Jürgen
A1  - Hennings, D.
A1  - Wernicke, R.
T1  - Ceramic multilayer capacitors. Hagemann, H. J.; Hennings, D.; Wernicke, R.
JF  - Philips' technical review / Philips' Gloeilampenfabrieken. Philips' Gloeilampenfabrieken <Eindhoven>. 41 (1984)
Y1  - 1984
SN  - 0031-7926
SP  - 89
EP  - 98
ER  - 
TY  - CHAP
A1  - Schiffer, Fabian
A1  - Bragard, Michael
T1  - Cascaded LQ and Field-Oriented Control of a Mobile Inverse Pendulum (Segway) with Permanent Magnet Synchronous Machines
T2  - 2019 20th International Conference on Research and Education in Mechatronics (REM)
Y1  - 2019
SN  - 978-1-5386-9257-8
U6  - http://dx.doi.org/10.1109/REM.2019.8744101
SP  - 1
EP  - 8
ER  - 
TY  - PAT
A1  - Nötzold, K.
A1  - Bragard, Michael
A1  - Fink, K.
A1  - Griessel, R.
A1  - Wegener, R.
T1  - Cascaded H-bridge converter with transformer based cell power balancing in each voltage level  : [Patentschrift]
Y1  - 2014
N1  - Titel des US-Patents: Bypassed cascaded cell converter : [patent of invention]. - Außerdem veröffentlicht als CN103997231 (A)
PB  - Europäisches Patentamt / United States Patent and Trademark Office [u.a.]
CY  - Den Haag / Alexandria, VA
ER  - 
TY  - JOUR
A1  - Schopp, Christoph
A1  - Doll, Timo
A1  - Gräser, Ulrich
A1  - Harzheim, Thomas
A1  - Heuermann, Holger
A1  - Kling, Rainer
A1  - Marso, Michael
T1  - Capacitively Coupled High-Pressure Lamp Using Coaxial Line Networks
JF  - IEEE Transactions on Microwave Theory and Techniques
N2  - This paper describes the development of a capacitively coupled high-pressure lamp with input power between 20 and 43 W at 2.45 GHz, using a coaxial line network. Compared with other electrodeless lamp systems, no cavity has to be used and a reduction in the input power is achieved. Therefore, this lamp is an alternative to the halogen incandescent lamp for domestic lighting. To serve the demands of domestic lighting, the filling of the lamp is optimized over all other resulting requirements, such as high efficacy at low induced powers and fast startups. A workflow to develop RF-driven plasma applications is presented, which makes use of the hot S-parameter technique. Descriptions of the fitting process inside a circuit and FEM simulator are given. Results of the combined ignition and operation network from simulations and measurements are compared. An initial prototype is built and measurements of the lamp's lighting properties are presented along with an investigation of the efficacy optimizations using large signal amplitude modulation. With this lamp, an efficacy of 135 lmW -1 is achieved.
Y1  - 2016
U6  - http://dx.doi.org/10.1109/TMTT.2016.2600326
SN  - 0018-9480
VL  - 64
IS  - 10
SP  - 3363
EP  - 3368
PB  - IEEE
CY  - New York, NY
ER  - 
TY  - JOUR
A1  - Heuermann, Holger
T1  - Calibration procedures with series impedances and unknown lines simplify on-wafer measurements
JF  - IEEE transactions on microwave theory and techniques : MTT ; a publication of the IEEE Microwave Theory and Techniques Society. 47 (1999), H. 1
Y1  - 1999
SN  - 0018-9480
SP  - 1
EP  - 5
ER  - 
TY  - JOUR
A1  - Heuermann, Holger
A1  - Schiek, Burkhard
T1  - Calibration of network analyser measurements with leakage errors
JF  - Electronics letters. 30 (1994), H. 1
Y1  - 1994
SN  - 0013-5194
SP  - 52
EP  - 53
ER  - 
TY  - JOUR
A1  - Claer, Mario
A1  - Ferrein, Alexander
A1  - Schiffer, Stefan
T1  - Calibration of a Rotating or Revolving Platform with a LiDAR Sensor
JF  - Applied Sciences
Y1  - 2019
U6  - http://dx.doi.org/10.3390/app9112238
SN  - 2076-3417
VL  - Volume 9
IS  - issue 11, 2238
PB  - MDPI
CY  - Basel
ER  - 
TY  - JOUR
A1  - Heuermann, Holger
T1  - Calibration of a Network Analyzer Without a Thru Connection for Nonlinear and Multiport Measurements
JF  - IEEE Transactions on Microwave Theory and Techniques. 56 (2008), H. 11, 1
Y1  - 2008
SN  - 0018-9480
SP  - 2505
EP  - 2510
ER  - 
TY  - JOUR
A1  - Schiffer, Stefan
A1  - Ferrein, Alexander
A1  - Lakemeyer, Gerhard
T1  - Caesar: an intelligent domestic service robot
JF  - Intelligent service robotics
N2  - In this paper we present CAESAR, an intelligent domestic service robot. In domestic settings for service robots complex tasks have to be accomplished. Those tasks benefit from deliberation, from robust action execution and from flexible methods for human–robot interaction that account for qualitative notions used in natural language as well as human fallibility. Our robot CAESAR deploys AI techniques on several levels of its system architecture. On the low-level side, system modules for localization or navigation make, for instance, use of path-planning methods, heuristic search, and Bayesian filters. For face recognition and human–machine interaction, random trees and well-known methods from natural language processing are deployed. For deliberation, we use the robot programming and plan language READYLOG, which was developed for the high-level control of agents and robots; it allows combining programming the behaviour using planning to find a course of action. READYLOG is a variant of the robot programming language Golog. We extended READYLOG to be able to cope with qualitative notions of space frequently used by humans, such as “near” and “far”. This facilitates human–robot interaction by bridging the gap between human natural language and the numerical values needed by the robot. Further, we use READYLOG to increase the flexible interpretation of human commands with decision-theoretic planning. We give an overview of the different methods deployed in CAESAR and show the applicability of a system equipped with these AI techniques in domestic service robotics
Y1  - 2012
U6  - http://dx.doi.org/10.1007/s11370-012-0118-y
SN  - 1861-2776
N1  - Special Issue on Artificial Intelligence Techniques for Robotics: Sensing, Representation and Action, Part I
VL  - 5
IS  - 4
SP  - 259
EP  - 276
PB  - Springer
CY  - Berlin
ER  - 
TY  - PAT
A1  - Heuermann, Holger
A1  - Hüning, Felix
A1  - Wache, Franz-Josef
T1  - Bussystem sowie Kommunikationsverfahren
N2  - Die Erfindung betrifft ein Bussystem enthaltend Busleitungen, an denen eine Anzahl von Busteilnehmern über einen Transceiver anschließbar sind, wobei der Transceiver eine bidirektionale Kommunikation zwischen mindestens zwei Busteilnehmern bewirkt, wobei auf einer busabgewandten Seite des Transceivers sich an denselben eine Zwischenbrückeneinheit anschließt, die mindestens zwei Sender-/Empfänger-Paare enthaltend jeweils einen Sender und einen Empfänger aufweist, wobei der Sender einen Senderoszillator, eine Amplituden- und/oder Phasen- und/oder Frequenzmodulator sowie eine Antenne aufweist und wobei der Empfänger einen Mischer aufweisenden Demodulator sowie eine Antenne aufweist, wobei ein erstes Sender-/Empfänger-Paar über eine Funkschnittstelle mit dem zweiten Sender-/Empfänger-Paar miteinander gekoppelt sind.
Y1  - 2018
N1  - Patent WO002018046055A1
ER  - 
TY  - JOUR
A1  - Czarnecki, Christian
T1  - Buchbesprechung : Anwendungsorientierte Wirtschaftsinformatik - Strategische Planung, Entwicklung und Nutzung von Informationssystemen
JF  - Anwendungen und Konzepte der Wirtschaftsinformatik (AKWI-Journal)
Y1  - 2020
U6  - http://dx.doi.org/10.26034/lu.akwi.2020.3264
SN  - 2296-4592
N1  - Das besprochene Buch ist im Katalog Plus als E-Book zu finden. Eine ältere Auflage steht im Regal unter der Grundsignatur 21 QGT 55
SP  - 101
EP  - 101
PB  - Technische Hochschule Wildau
CY  - Wildau
ER  - 
TY  - CHAP
A1  - Sajatovic, Miodrag
A1  - Rihacek, Christoph
A1  - Haindl, Bernhard
A1  - Schnell, Michael
A1  - Brandes, Sinja
A1  - Gligorevic, Snjezana
T1  - Broadband VHF (B-VHF) project achievements and follow-on activities
T2  - Integrated Communications, Navigation and Surveillance Conference : Herndon, VA, 1 - 3 May 2007
Y1  - 2007
SN  - 1-4244-1216-1
SP  - 1
EP  - 8
ER  - 
TY  - CHAP
A1  - Krause, Gregor
T1  - Brenchmarking elektrischer Energie in Zweckbauten - Aussagefähigkeit von Energiekennzahlen
T2  - Betriebliches Energiemanagement : Tagung Cottbus, 6. und 7. März 2001. (VDI-Berichte ; 1593)
Y1  - 2001
SN  - 3180915935
SP  - 413
EP  - 422
PB  - VDI-Verlag
CY  - Düsseldorf
ER  - 
TY  - JOUR
A1  - Zastrow, Udo
A1  - Rieder, G.
T1  - Bracketing eigenvalues of an oscillating elastic body by integral equations
JF  - Bracketing of eigenfrequencies of continous structures : Euromech Colloquium, no. 112, Mátrafüred (Hungary), 21 - 23 February, 1979 / ed. by À. Bosznay
Y1  - 1980
SN  - 963-05-2625-5
N1  - Euromech Colloquium <112, 1979, Mátrafüred>
SP  - 421
EP  - 434
PB  - Akad. Kiadó
CY  - Budapest
ER  - 
TY  - JOUR
A1  - Heuermann, Holger
A1  - Erkens, Holger
T1  - Blocking structures for mixed-mode systems. / Erkens, Holger ; Heuermann, Holger
JF  - Conference proceedings : Tuesday 12th, Wednesday 13th and Thursday 14th October, [RAI International Exhibition and Congress Centre, Amsterdam ; part of European Microwave Week 2004] / EuMA, European Microwave Association. Vol. 1
Y1  - 2004
SN  - 1-580-53992-0
N1  - European Microwave Conference ; (34, 2004, Amsterdam) ; European Microwave Week ; (7, 2004, Amsterdam)
SP  - 297
EP  - 300
PB  - Horizon House Publ.
CY  - London
ER  - 
TY  - JOUR
A1  - Hagebeuker, Bianca
A1  - Lange, Robert
A1  - Ringbeck, Thorsten
T1  - Bildverarbeitung mit der dritten Dimension : wenn die Pixel auch Laufzeiten auswerten
JF  - Sensor-Report : Sensorik, Messtechnik, Bildverarbeitung, Fabrikautomation. - 2004, H. 2
Y1  - 2004
SN  - 0179-9592
SP  - 11
EP  - 17
PB  - Rek & Thomas
CY  - St. Gallen
ER  -