TY  - JOUR
A1  - Meliß, Michael
A1  - Oesterwind, Dieter
A1  - Voß, Alfred
T1  - Non-nuclear and non-fossil energy resources and their possibilities for future power generation
JF  - Kerntechnik
N2  - It must be stressed that the assessment of the exploitation possibilities of the energy resources discussed in this paper requires further studies. With this proviso, the situation can be provisionally summarised as follows: The total potential of known geothermal steam sources is only 64 GW. Geothermal energy could therefore only make a significant contribution to covering the worldwide power needs if we succeed in exploiting dry geothermal reservoirs. Exploitation of tidal energy is limited to a few geographically favourable locations. The power generation potential at these locations is only about 64 GW. An important drawback of tidal power is discontinuous power generation. Large scale exploitation of wind, wave and glacier energy, and of ocean heat, requires solution of a number of technological problems. The environmental effects of exploitation of these energy resources are to some extent of a qualitatively different nature from those of operation of fossil-fuel-fired and of nuclear power plants. The scanty knowledge in this area often results in these effects being underestimated. In any case, however, it would be deliberately misleading to postulate that any form of power generation is possible without some detrimental effects on the environment. It may be stated in conclusion that, owing to their small potential or to the as yet insufficiently advanced technological development, none of the energy resources discussed in this paper can make a significant contribution to the solution of middle-term energy supply problems, i.e., to a rapid replacement of mineral oil and natural gas.
Y1  - 1975
U6  - http://dx.doi.org/10.18419/opus-8093
SN  - 0932-3902
N1  - Printausg. in der Bibliothek vorhanden: 63 ZS 010-1975
VL  - 17
IS  - 7
SP  - 301
EP  - 306
PB  - De Gruyter
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Hellmanns, Mark
A1  - Hartung, I.
A1  - Dilger, Klaus
A1  - Böhm, Stefan
T1  - Quality assurance of manual guided joining and welding devices
T2  - Proceedings of the IIW International Conference on Advances in Welding and Allied Technologies : July 16 - 17, 2009, Singapore
Y1  - 2009
SN  - 9789810832605
SP  - 219
EP  - 222
PB  - International Institute of Welding
CY  - Roissy
ER  - 
TY  - CHAP
A1  - Goldbach, Daniel
A1  - Ament, Christoph
ED  - Scharff, Peter
T1  - Stabilized reversing with vehicle trailer combinations
T2  - Crossing borders within the ABC : automation, biomedical engineering and computer science; proceedings; 55. IWK Internationales Wissenschaftliches Kolloquium; 13 - 17 September 2010, Ilmenau
Y1  - 2010
SN  - 978-3-938843-53-6
SP  - 352
EP  - 357
PB  - Verl. ISLE
CY  - Ilmenau
ER  - 
TY  - CHAP
A1  - Hartung, I.
A1  - Dilger, Klaus
A1  - Hellmanns, Mark
A1  - Böhme, Stefan
T1  - Repair of non-weldable steel structures to extend the life cycle
T2  - Proceedings of the IIW International Conference on Advances in Welding and Allied Technologies : July 16 - 17, 2009, Singapore. (Welding in the world ; 53.2009, special issue)
Y1  - 2009
SN  - 978-981-08-3259-9
SP  - 569
EP  - 574
PB  - Springer
CY  - Berlin [u.a.]
ER  - 
TY  - CHAP
A1  - Hellmanns, Mark
A1  - Böhm, Stefan
A1  - Dilger, Klaus
T1  - Weight and noise reduction in power transmissions through epoxy resin foams
T2  - Proceedings of the 31st annual meeting of the Adhesion Society : 17. - 20.2.2008, Austin, Texas
Y1  - 2008
SP  - 291
EP  - 293
PB  - Adhesion Society
CY  - Blacksburg
ER  - 
TY  - CHAP
A1  - Hellmanns, Mark
A1  - Böhm, Stefan
A1  - Dilger, Klaus
T1  - Implementation of a velocity controlled manual applicator for adhesives and sealants in the automotive industry in consideration of quality control
T2  - Proceedings of the 29th annual meeting of the Adhesion Society : 19. - 22.2.2006, Jacksonville, Florida
Y1  - 2006
SN  - 1086-9506
SP  - 68
EP  - 70
PB  - Adhesion Society
CY  - Blacksburg, Va.
ER  - 
TY  - JOUR
A1  - Hellmanns, Mark
A1  - Böhm, Stefan
A1  - Dilger, Klaus
T1  - Manual applications of adhesives
JF  - Journal of adhesion and interface
Y1  - 2006
VL  - Vol. 7
IS  - No. 4
SP  - 24
EP  - 27
ER  - 
TY  - CHAP
A1  - Hellmanns, Mark
A1  - Böhm, Stefan
A1  - Dilger, Klaus
T1  - Progress of the manual application of adhesives
T2  - Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China
Y1  - 2006
SP  - 275
EP  - 277
PB  - Beijing Adhesion Society of China
CY  - Beijing
ER  - 
TY  - CHAP
A1  - Böhm, Stefan
A1  - Hellmanns, Mark
A1  - Backes, Andreas
A1  - Dilger, Klaus
T1  - Lock-in thermography based NDT of automotive parts
T2  - Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China
Y1  - 2006
SP  - 382
EP  - 384
PB  - Beijing Adhesion Society of China
CY  - Beijing
ER  - 
TY  - JOUR
A1  - Böhm, Stefan
A1  - Hellmanns, Mark
A1  - Backes, Andreas
A1  - Dilger, Klaus
T1  - Lock-in thermography based NDT of parts for the automotive industry
JF  - Journal of adhesion and interface
Y1  - 2006
VL  - Vol. 7
IS  - No. 4
SP  - 10
EP  - 12
ER  - 
TY  - CHAP
A1  - Stollenwerk, Dominik
A1  - Kuvarakul, T.
A1  - Kuperjans, Isabel
T1  - Renewable energy supply for power dominated, energy intense production processes - a systematic conversion approach for the anodizing process
T2  - IOP conference series: Earth and environmental science (EES)
Y1  - 2013
SN  - 1755-1315
SN  - 1755-1307
VL  - Vol. 16
IS  - H. 1
SP  - 012142/1
EP  - 012142/4
ER  - 
TY  - JOUR
A1  - Sabitova, A.
A1  - Ebert, Ph.
A1  - Lenz, A.
A1  - Schaafhausen, S.
A1  - Ivanova, L.
A1  - Dähne, M.
A1  - Hoffmann, A.
A1  - Dunin-Borkowski, R. E.
A1  - Förster, Arnold
A1  - Grandidier, B.
A1  - Eisele, H.
T1  - Intrinsic bandgap of cleaved ZnO(112¯0) surfaces
JF  - Applied physics letters
Y1  - 2013
SN  - 1077-3118 (E-Journal); 0003-6951 (Print)
VL  - Vol. 102
SP  - 021608
ER  - 
TY  - CHAP
A1  - Takenaga, Shoko
A1  - Herrera, Cony F.
A1  - Werner, Frederik
A1  - Biselli, Manfred
A1  - Schnitzler, Thomas
A1  - Schöning, Michael Josef
A1  - Öhlschläger, Peter
A1  - Wagner, Torsten
T1  - Detection of the metabolic activity of cells by differential measurements based on a single light-addressable potentiometric sensor chip
T2  - 11. Dresdner Sensor-Symposium : 9.-11.12.2013
Y1  - 2013
SN  - 978-3-9813484-5-3
SP  - 63
EP  - 67
ER  - 
TY  - CHAP
A1  - Feldhusen, Jörg
A1  - Brezing, Alexander Nikolaus
A1  - Pütz, Claus
A1  - Wählisch, Georg
T1  - Multi-system CAD-teaching in large classes
T2  - When design education and design research meet : proceedings of the 12th International Conference on Engineering and Product Design Education, Norwegian University of Science and Technology (NTNU) Trondheim, Norway, 2nd - 3rd September 2010 ; [E&PDE]
Y1  - 2010
SN  - 978-1-904670-19-3
SP  - 204
EP  - 209
PB  - Design Society
CY  - Glasgow
ER  - 
TY  - CHAP
A1  - Kumaran, P.
A1  - Gopinathan, M.
A1  - Razali, N. M.
A1  - Kuperjans, Isabel
A1  - Hariffin, B.
A1  - Hamdan, H.
T1  - Preliminary evaluation of atomization characteristics of improved biodiesel for gas turbine application
T2  - IOP Conference Series: Earth and Environmental Science (EES)
Y1  - 2013
U6  - http://dx.doi.org/10.1088/1755-1315/16/1/012014
SN  - 1755-1315
VL  - 16
IS  - 1
SP  - 012014/1
EP  - 012014/4
PB  - Institute of Physics Publishing (IOP)
CY  - London [u.a.]
ER  - 
TY  - CHAP
A1  - Rens, Gavin
A1  - Ferrein, Alexander
A1  - Poel, Etienne van der
T1  - Extending DTGolog to deal with POMD-Ps
T2  - Proceedings of the Nineteenth Annual Symposium of the Pattern Recognition Association of South Africa (PRASA 2008)
Y1  - 2008
SP  - 49
EP  - 54
ER  - 
TY  - JOUR
A1  - Alebouyeh Samami, Behzad
A1  - Pieper, Martin
A1  - Breitbach, Gerd
A1  - Hodapp, Josef
T1  - Heat production in the windings of the stators of electric machines under stationary condition
JF  - Heat and mass transfer
N2  - In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results.
Y1  - 2014
U6  - http://dx.doi.org/10.1007/s00231-014-1371-8
SN  - 0947-7411 (Print) ; 1432-1181 (E-Journal)
VL  - 50
SP  - 1707
EP  - 1716
PB  - Springer
CY  - Heidelberg
ER  - 
TY  - CHAP
A1  - Augenstein, Eckardt
A1  - Kuperjans, Isabel
A1  - Lucas, K.
ED  - Tsatsaronis,, Georgios
T1  - EUSEBIA - Decision-Support-System for Technical, Economical and Ecological Design and Evaluation of Industrial Energy Systems
T2  - ECOS 2002 : proceedings of the 15th International Conference on Efficiency, Costs, Optimization, Simulation and Environmental Impact of Energy Systems, Berlin, Germany July 3 - 5, 2002. - Vol. 1
Y1  - 2002
SN  - 3-00-009533-0
SP  - 446
EP  - 453
PB  - Techn. Univ., Inst. for Energy Engineering
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Augenstein, Eckardt
A1  - Herbergs, S.
A1  - Kuperjans, Isabel
A1  - Lucas, K.
ED  - Kjelstrup, Signe
T1  - Simulation of industrial energy supply systems with integrated cost optimization
T2  - Proceedings of ECOS 2005, the 18th International Conference on Efficiency, Cost, Optimization, Simulation, and Environmental Impact of Energy Systems : Trondheim, Norway, June 20 - 22, 2005. - Vol. 2
Y1  - 2005
SN  - 82-519-2041-8
N1  - CD-ROM-Ausg. u.d.T.: Shaping our future energy systems
SP  - 627
EP  - 634
PB  - Tapir Academic Press
CY  - Trondheim
ER  - 
TY  - JOUR
A1  - Marx, Ulrich
A1  - Schenk, Friedrich
A1  - Behrens, Jan
A1  - Meyr, Ulrike
A1  - Wanek, Paul
A1  - Zang, Werner
A1  - Schmitt, Robert
A1  - Brüstle, Oliver
A1  - Zenke, Martin
A1  - Klocke, Fritz
T1  - Automatic production of induced pluripotent stem cells
JF  - Procedia CIRP : First CIRP Conference on BioManufacturing
Y1  - 2013
SN  - 2212-8271
VL  - Vol. 5
SP  - 2
EP  - 6
PB  - Elsevier
CY  - Amsterdam
ER  -