TY - GEN A1 - Tippkötter, Nils A1 - Pasteur, A. A1 - Meyer, C. A1 - Kampeis, P. A1 - Diller, R. A1 - Ulber, Roland T1 - Aufreinigung von Cephalosporin C durch poröse, selektiv-beschichtete Magnetpartikel T2 - Chemie Ingenieur Technik N2 - Die selektive Isolierung von Cephalosporin C (CPC) aus komplexen Fermentationssuspensionen unter Einsatz magnetischer Separation ist das Ziel dieser Arbeit. Das Verfahren wird im frühen Stadium der Aufarbeitung genutzt, um CPC zu stabilisieren und somit die Produktausbeute zu erhöhen. Als Adsorbersysteme für CPC wurden neben einem projektinternen magnetischen Material ND 10322, dessen Oberflächenladungen spezifisch für die Bindung des Zielmoleküls synthetisiert wurden, verschiedene kommerzielle Partikelsysteme verglichen. Es konnten massenspezifische Maximalbeladungen von 51 mg g⁻¹ erreicht werden. Weiterhin wurde die Stabilität von CPC untersucht. Unter optimalen Adsorptionsbedingungen kann CPC stabilisiert werden, so dass die Geschwindigkeitskonstante der Degradation des b-Lactam-Rings unter diesen Bedingungen unter 0,005 h⁻¹ liegt. Untersuchungen zur Wiederverwertbarkeit der neuen Adsorbers zeigten eine irreversible Bindung geringer CPC-Mengen nach dem ersten Einsatz. Nach zwölf Zyklen tritt eine irreversible Bindung von CPC ein, was zu einer signifikanten Reduktion der Adsorptionsfähigkeit führt. Die Anhäufung des CPC auf dem Adsorber konnte durch IR-Untersuchungen auf die Bildung einer Peptidbindung zwischen Carboxylgruppen des CPC und Aminogruppe der Adsorberoberfläche zurückgeführt werden. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250391 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1369 EP - 1370 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Nötzold, K. A1 - Uphues, A. A1 - Wegener, R. A1 - Soter, S. A1 - Fink, K. A1 - Bragard, Michael A1 - Griessel, R. T1 - Inverter based test setup for LVRT verification of a full-scale 2 MW wind power converter T2 - EPE Joint Wind Energy and T&D Chapters Seminar : 28th and 29th of June 2012, in the Utzon Centre, Aalborg, Denmark ; papers, posters, presentations. - Session 2: Grid connection, compliance Y1 - 2012 PB - EPE Association CY - Brussels ER - TY - GEN A1 - Duwe, A. A1 - Tippkötter, Nils A1 - Leipold, D. A1 - Riemer, S. A1 - Zorn, H. A1 - Ulber, Roland T1 - Holzhydrolyse als Feststoffreaktion: Charakterisierung von Inhibitoren und Erhöhung der Ausbeute durch den Einsatz lignolytischer Enzyme T2 - Chemie Ingenieur Technik N2 - Der Erhalt möglichst hoher Zuckerkonzentrationen für nachfolgende Fermentationen und eine Steigerung der Produktivität sind Ziele der Hydrolyse bei hohen Feststoffkonzentrationen im Rahmen des Projekts „Lignocellulose Bioraffinerie“. Verwendet wird durch ein Organosolv-Verfahren aufgeschlossenes Buchenholz. Die Hydrolyse des Faserstoffes erfolgt mithilfe von CTec2-Enzymen (Fa. Novozymes). Zurzeit können unter Einsatz eines neuen Feststoffreaktors Cellulosefasern in einer Konzentration bis 400 g L⁻¹ enzymatisch hydrolysiert werden. Dabei werden Ausbeuten (g Glucose/g Cellulose im Faserstoff) bis 0,86 g g⁻¹ und Glucosekonzentrationenvon 120 g L⁻¹ erreicht. Ein Nachteil ist jedoch die hierbei auftretende Abnahme der Hydrolyseausbeuten. Zahlreiche Limitierungen bezüglich der Hydrolysierbarkeit von Lignocellulose werden zurzeit diskutiert und publiziert. Ziel der Untersuchungen ist die Identifizierung hydrolysehemmender Substanzen sowie die Erhöhung der Ausbeute an Zuckermonomeren durch den Einsatz lignolytischer Enzyme. Hierbei wird eine HPLC-MS-Methode zur Charakterisierung hemmender Substanzen eingesetzt, um potenzielle Inhibitoren zu erfassen. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250298 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1307 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Fabo, Sabine A1 - Lemke, Inga ED - Hartmann, Doreen ED - Nitsche, Jessica T1 - Gefährliche Liebschaften : Kunst zwischen Wderstand und Umarmung T2 - Interventionen : Grenzüberschreitungen in Ästhetik, Politik und Ökonomie Y1 - 2012 SN - 978-3-7705-5283-2 SP - 173 EP - 189 PB - Fink CY - München [u.a.] ER - TY - JOUR A1 - Chwallek, Constanze A1 - Engelen, Andreas A1 - Oswald, Monika A1 - Brettel, Malte T1 - Die Wir­kung des Füh­rungs­ver­hal­tens des Top-Ma­nage­ments auf die un­ter­neh­me­ri­sche Ori­en­tie­rung – ein 5-Län­der-Ver­gleich JF - Zfbf : Schmalenbachs Zeitschrift für betriebswirtschaftliche Forschung Y1 - 2012 SN - 0341-2687 IS - 2 SP - 138 EP - 165 PB - Springer Fachmedien CY - Wiesbaden ER - TY - GEN A1 - Wiesen, S. A1 - Tippkötter, Nils A1 - Muffler, K. A1 - Sohling, U. A1 - Ruf, F. A1 - Ulber, Roland T1 - Nutzung von Rohglycerin: Rohglycerin-Aufarbeitung, Herstellung von 1, 3-Propandiol und Rückgewinnung von Fettsäuren T2 - Chemie Ingenieur Technik N2 - Die fermentative Verwertung von Rohglycerin setzt je nach Herstellungsmethode und Produktionsorganismus eine Vorbehandlung des Glycerins zur Entfernung von Produktinhibitoren voraus. Durch den Einsatz von Hydrotalcit-Adsorbern können die im Rohglycerin enthaltenen Fettsäuren entfernt werden. Durch diese einfache Aufarbeitungsmethode ist ein mit reinem Glycerin vergleichbarer Umsatz von stark mit Fettsäuren verunreinigtem Rohglycerin zu 1,3-Propandiol (PDO) möglich. Die durch den Hydrotalcit gebundenen Fettsäuren lassen sich mit einem Ethanol-Wasser-Gemisch eluieren. Somit kann der Adsorber regeneriert und die Fettsäuren wieder der Wertschöpfungskette zugeführt werden. Im Fed-Batch-Experiment kann mit C. diolis eine PDO-Konzentration von über 50 g L⁻¹ unter Verwendung des aufgereinigten Rohglycerins erzielt werden. In der industriellen Produktion wird PDO momentan destillativ aufgearbeitet. Ein adsorptives Aufarbeitungsverfahren kann den Energiebedarf des Herstellungsprozesses drastisch senken. Auf der Suche nach einem geeigneten Material wurde ein Adsorberscreening in Bezug auf die Bindungseigenschaften durchgeführt. Mit einem b-Zeolith der Firma Süd ChemieAG konnte bisher die höchste Beladung im Modellsystem von 120 mg PDO/gAdsorber erreicht werden. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250265 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1296 PB - Wiley-VCH CY - Weinheim ER - TY - THES A1 - Stapenhorst, Carolin T1 - The concept as an operant instrument within the interdisciplinarity of the architectural design process N2 - In the introduction to their book "What is philosophy?" Gilles Deleuze and Felix Guattari deplore the inflationary and trivialised use of the term concept: "Finally, the most shameful moment came when computer science, marketing, design and advertising, all the disciplines of communication, seized hold of the word concept itself and said: 'This is our concern, we are the creative ones, we are the ideas men! We are the friends of the concept, we put in our computers.' " This doctoral thesis shares the concern of Gilles Deleuze and Felix Guattari, but still, it is a thesis in architecture and thus collocated within the field of the representatives of the "ideas men". It engages in architectural design theory, and refers in particular to the investigation of methodological approaches within the design process. Therefore, the thesis will not contribute to the philosophical dimension of the term, but intends to overcome its imprecise use within the architectural discourse, in compliance with Eugène Viollet-le-Duc's admonition relative to vague definitions: "Dans les arts, et dans l'architecture en particulier, les définitions vagues ont causé bien des erreurs, ont laissé germer bien des préjugés, enraciner bien des idées fausses. On met un mot en avant, chacun y attache un sens différent." The term concept in architecture is very often used as pure marketing collateral, it serves to sell an idea, a product, a design. Its functional applicability is reduced to a special manner of illustration, produced as one of the various design presentation documents at the end of the design process. In contrast, the original contribution of this thesis aims to give a precise, instrumental dimension to the term concept: the concept is the expression of a specific logic, capable to guide the decisional sequences of the process and thus to improve the quality of the designed projects. The motivation to define a specific instrumentality of the concept is closely connected to the issue of interdisciplinarity in the architects’ profession. The interdisciplinary character of the architectural field is widely accepted and discussed as such, but the thesis intends to give a more precise definition of the various kinds of competences involved by classifying them into either the internal or the external group. The traditional notion of interdisciplinarity, predominantly seen as collaboration between architects and technical experts, and, most notably, the historical, sometimes contentious, relationship between architects and engineers is described. Referring to recent developments, the transformation of the architect’s role within the professional sphere, marked by an increasing importance of diverse influences and linked to a growing risk of marginalisation, is illustrated. The thesis describes different ways to adapt to this specific kind of interdisciplinarity, which generally requires the architect’s ability to connect and to integrate various contents, different points of view and diverse scales. On the other hand, the big potential which is implicit in the interdisciplinary field is exposed: architects can inform their core competence, the design, by extracting contents of different disciplinary competences, pertaining or not pertaining to their own professional field. They have the possibility to cross fields of external competences in a selective way and by doing so they can build up a corpus of knowledge capable to generate and communicate guidelines and systematic methodologies for their design. At the end, the analysis of these two aspects allows the definition of a more specific professional profile of the architect as specialist of interdisciplinarity. The thesis is concerned with the theories around the design process. The design process is seen as open to inspection and critical evaluation, with major focus on the decisional sequences which characterise it. It concentrates on the process’ descriptiveness and the degree of self-conscious approaches applied within it. The importance of regulative, strategic mechanisms is illustrated by testimonies taken from a series of design researches and leads to the functional definition of the figure of the concept as representation of a coherent set of ideas, as generator of a project-specific system of rules and as communicator of decisional strategies. The concept's function is furthermore defined as communicative interface which generates and transmits the system of rules authoritative for all the disciplinary competences involved in the design process, a communicative interface which constitutes a basis of shared convictions capable to increase the efficiency of collaboration. Furthermore, the concept's capacity to explore and elaborate the contents of external disciplines is identified as a possible methodological approach to innovative design thinking. The approach to a specific functional definition of the concept is continued by the description of a series of instruments that are simultaneously generating and communicating it. It is outlined to which degree the concept itself is already the result of an ideational process, collocated within the initial phase of the design proceedings, serving as a guideline to them, but still continuously evolving and adapting in its progression. In addition, it is illustrated how all the diverse instruments of the concept are operational media through which the knowledge transition between different disciplines can occur. The considerations about the concept as operational instrument of design are elaborated with regard to a number of examples of didactical applications that are particularly involved in the development and teaching of specific design methods. These examples illustrate the interrelations between design theory and design education. They are derived from very different schools of architecture and diverse mindsets, but all of them transmit models of conceptual design thinking. KW - methodologies KW - instruments KW - interdisciplinarity KW - architectural design process KW - design theory Y1 - 2012 PB - Politecnico di Torino CY - Turin ER - TY - GEN A1 - Frauenrath, Tobias A1 - Fuchs, Katharina A1 - Hezel, Fabian A1 - Dieringer, Matthias A. A1 - Rieger, Jan A1 - Niendorf, Thoralf T1 - Improved cardiac triggering by combining multiple physiological signals: a cardiac MR feasibility study at 7.0 T T2 - 2012 ISMRM Annual Meeting Proceedings N2 - In current clinical cardiovascular MR (CMR) practice cardiac motion is commonly dealt with using ECG based synchronization. However, ECG is corrupted by magneto-hydrodynamic (MHD) effects in magnetic fields. This leads to artifacts in the ECG trace and evokes severe T-wave elevations, which might be misinterpreted as R-waves resulting in erroneous triggering. At (ultra)high field strengths, the propensity of ECG recordings to MHD effects is further pronounced. Pulse oximetry (POX) being inherently sensitive to blood oxygenation provides an alternative approach for cardiac gating. However, due to the travel time of the blood the peak of maximum oxygenation and hence the trigger is delayed by approx. 300 ms with respect to the ECG's R-wave. Also the peak of maximum oxygenation shows a jitter of up to 65 ms. Alternative triggering approaches include acoustic cardiac triggering (ACT). In current clinical practice cardiac gating / triggering commonly relies on using single physiological signals only. Realizing this limitation this study proposes a combined triggering approach which exploits multiple physiological signals including ECG, POX or ACT to track cardiac activity. The feasibility of the coupled approach is examined for LV function assessment at 7.0 T. For this purpose, breath-held 2D-CINE imaging in conjunction with cardiac synchronization was performed paralleled by real time logging of physiological waveforms to track (mis)synchronization between the cardiac cycle and data acquisition. Combinations of the ECG, POX and ACT signals were evaluated and processed in real time to facilitate reliable trigger information. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Gräßl, Andreas A1 - Renz, Wolfgang A1 - Hezel, Fabian A1 - Frauenrath, Tobias A1 - Pfeiffer, Harald A1 - Hoffmann, Werner A1 - Kellmann, Peter A1 - Martin, Conrad A1 - Niendorf, Thoralf T1 - Design, evaluation and application of a modular 32 channel transmit/receive surface coil array for cardiac MRI at 7T T2 - 2012 ISMRM Annual Meeting Proceedings N2 - Cardiac MR (CMR) at ultrahigh (≥7.0 T) fields is regarded as one of the most challenging MRI applications. At 7.0 T image quality is not always exclusively defined by signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR). Detrimental effects bear the potential to spoil the signal-to-noise (SNR) and contrast-to-noise (CNR) benefits of cardiac MR (CMR) at 7.0 T. B₁⁺-inhomogeneities and signal voids represent the main challenges. Various pioneering coil concepts have been proposed to tackle these issues, enabling cardiac MRI at 7.0 T. This includes a trend towards an ever larger number of transmit and receive channels. This approach affords multi-dimensional B₁⁺ modulations to improve B₁⁺ shimming performance and to enhance RF efficiency. Also, parallel imaging benefits from a high number of receive channels enabling two-dimensional acceleration. Realizing the limitations of existing coil designs tailored for UHF CMR and recognizing the opportunities of a many element TX/RX channel architecture this work proposes a modular, two dimensional 32-channel transmit and receive array using loop elements and examines its efficacy for enhanced B¹+ homogeneity and improved parallel imaging performance. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Tkachenko, Valeriy A1 - von Knobelsdorff-Brenkenhoff, Florian A1 - Kleindienst, Denise A1 - Winter, Lukas A1 - Rieger, Jan A1 - Frauenrath, Tobias A1 - Dieringer, Matthias A. A1 - Santoro, Davide A1 - Niendorf, Thoralf A1 - Schulz-Menger, Jeanette T1 - Cardiovasular MR at 7Tesla: assessment of the right ventricle T2 - 2012 ISMRM Annual Meeting Proceedings N2 - The assessment of the right ventricle (RV) is a challenge in today's cardiology, but of growing clinical impact regarding patient prognosis in different cardiac diseases. The detection and differentiation of small wall motion abnormalities may help to enhance the differentiation of cardiomyopathies including Arrhythmogenic Rightventricular Cardiomyopathy. Cardiovascular magnetic resonance (CMR) at 1.5T is the accepted gold standard for RV quantification. The higher spatial resolution achievable at ultrahigh field strength (UHF) offers the potential to gain new insights into the structure and function of the RV. To approach this goal accurate RV chamber quantification at 7T has to be proven. Consequently this study examines the feasibility of assessment of RV dimensions and function at 7T using improved spatial resolution enabled by the intrinsic sensitivity gain of UHF CMR. For this purpose, a dedicated 16 channel TX/RX RF coil array is used together with 2D CINE fast gradient echo (FGRE) imaging. For comparison RV chamber quantification is conducted at 1.5T using a SSFP based state of the art clinical protocol. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Frauenrath, Tobias A1 - Pfeiffer, Harald A1 - Hezel, Fabian A1 - Dieringer, Matthias A. A1 - Winter, Lukas A1 - Gräßl, Andreas A1 - Santoro, Davide A1 - Özerdem, Celal A1 - Renz, Wolfgang A1 - Greiser, Andreas A1 - Niendorf, Thoralf T1 - Lessons learned from cardiac MRI at 7.0 T: LV function assessment at 3.0 T using local multi-channel transceiver coil arrays T2 - 2012 ISMRM Annual Meeting Proceedings N2 - Cardiac MR (CMR) is of proven clinical value but also an area of vigorous ongoing research since image quality is not always exclusively defined by signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR). Recent developments of CMR at 7.0 T have been driven by pioneering explorations into novel multichannel transmit and receive coil array technology to tackle the challenges B1+-field inhomogeneities, to offset specific-absorption rate (SAR) constraints and to reduce banding artifacts in SSFP imaging. For this study, recognition of the benefits and performance of local surface Tx/Rx-array structures recently established at 7.0 T inspired migration to 3.0 T, where RF inhomogeneities and SAR limitations encountered in routine clinical CMR, though somewhat reduced versus the 7.0 T situation, remain significant. For all these reasons, this study was designed to build and examine the feasibility of a local four channel Tx/Rx cardiac coil array for anatomical and functional cardiac imaging at 3.0 T. For comparison, a homebuilt 4 channel Rx cardiac coil array exhibiting the same geometry as the Tx/Rx coil and a Rx surface coil array were used. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - GEN A1 - Lindel, Tomasz Dawid A1 - Greiser, Andreas A1 - Waxman, Patrick A1 - Dietterle, Martin A1 - Seifert, Frank A1 - Fontius, Ulrich A1 - Renz, Wolfgang A1 - Dieringer, Matthias A. A1 - Frauenrath, Tobias A1 - Schulz-Menger, Jeanette A1 - Niendorf, Thoralf A1 - Ittermann, Bernd T1 - Cardiac CINE MRI at 7 T using a transmit array T2 - 2012 ISMRM Annual Meeting Proceedings N2 - With its need for high SNR and short acquisition times, Cardiac MRI (CMR) is an intriguing target application for ultrahigh field MRI. Due to the sheer size of the upper torso, however, the known RF issues of 7T MRI are also most prominent in CMR. Recent years brought substantial progress but the full potential of the ultrahigh field for CMR is yet to be exploited. Parallel transmission (pTx) is a promising approach in this context and several groups have already reported B1 shimming for 7T CMR. In such a static pTx application amplitudes and phases of all Tx channels are adjusted individually but otherwise imaging techniques established in current clinical practice 1.5 T and 3 T are applied. More advanced forms of pTx as spatially selective excitation (SSE) using Transmit SENSE promise additional benefits like faster imaging with reduced fields of view or improved SAR control. SSE requires the full dynamic capabilities of pTx, however, and for the majority of today's implemented pTx hardware the internal synchronization of the Tx array does not easily permit external triggering as needed for CMR. Here we report a software solution to this problem and demonstrate the feasibility of CINE CMR at 7 T using a Tx array. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - THES A1 - Büdenbender, Martin T1 - Entflechtungskonzepte für Stromübertragungsnetze : ein ökonomischer Vergleich T2 - Münstersche Schriften zur Kooperation ; Bd. 101 N2 - Netzsektoren und deren adäquate Regulierung sind ein sehr relevantes und aktuelles Thema. Dies gilt sowohl für die ökonomische Theorie, die sich sehr intensiv damit auseinandersetzt und in den letzten Jahrzehnten zahlreiche neue Erkenntnisse gewonnen hat. Es gilt ebenso für die Politik, in der Regulierungsfragen kontrovers diskutiert werden und dies nicht nur unter ökonomischen Gesichtspunkten. Es gilt selbstverständlich für die regulierten Unternehmen selbst, deren Tätigkeit durch die staatlichen Regulierungsvorgaben markant beeinflusst wird. Nicht nur die konkreten Inhalte der Regulierungsregime sowie die verbleibenden Freiheitsgrade in der Ausgestaltung sind von Bedeutung, sondern ebenso die Umsetzung durch die Regulierungsbehörden. All dies gilt für den Strommarkt und seinen regulatorischen Hintergrund in besonderer Weise. Die Entflechtung der Stromübertragungsnetze von der Stromproduktion und damit die Vorgaben für die Organisation der Wertschöpfungsketten in den Elektrizitätsunternehmen sind seit dem Beginn des europäischen Liberalisierungsprozesses der Strommärkte ein wichtiges und kontrovers diskutiertes Regulierungselement. Den Fokus bildet das vertikale Unbundling, das letztlich die Diskriminierung von Wettbewerbern durch Anbieter mit aggregierten Wertschöpfungsketten verhindern soll, indem diese gezwungen werden, ihren "Netzteil" anders zu organisieren oder zu verkaufen. Den Mitgliedsstaaten blieben Freiräume in der Ausgestaltung, die in Deutschland erst vor kurzem konkretisiert wurden, und die für die regulierten Unternehmen die Nutzung eines Wahlrechts beinhalten. Der wirtschaftspolitischen folgt nun eine unternehmerische Abwägungsentscheidung. KW - Energiewirtschaft KW - Ownership Unbundling KW - Übertragungsnetz KW - Stromnetz KW - 3. EU Legislativpaket Y1 - 2012 SN - 978-3-8440-1460-0 N1 - Zugl.: Münster (Westfalen), Univ., Diss., 2012 Inhaltsverzeichnis: https://d-nb.info/1027395791/04 PB - Shaker CY - Düren ER - TY - JOUR A1 - Butenweg, Christoph A1 - Fehling, Ekkehard T1 - Hintergrund für die vereinfachten Regeln bei Mauerwerksgebäuden im Erdbebenfall JF - Mauerwerk : European journal of masonry N2 - Bei der Ausarbeitung des nationalen Anwendungsdokumentes zur DIN EN 1998-1 waren die in der ENV-Fassung enthaltenen vereinfachten Regeln im Lichte aktueller Forschungsergebnisse zu überprüfen und zu überarbeiten. Die gleiche Aufgabe stellte sich auch für die Neufassung der DIN 4149. In beiden Fällen sind neben konstruktiven Regeln für die Art und Anordnung der zur Gebäudeaussteifung heranzuziehenden Wände im Grundriss Tabellen enthalten, die unter bestimmten Bedingungen den Entfall eines rechnerischen Nachweises der Tragwände im Erdbebenfall ermöglichen. Dies ist für Schwachbebengebiete, wie sie in Deutschland und anderen Ländern Mitteleuropas anzutreffen sind, sinnvoll, um unnötigen Rechenaufwand sowie Probleme mit der Führbarkeit von Nachweisen so weit wie möglich auszuschalten. Im vorliegenden Beitrag werden die Hintergründe der vereinfachten Regeln diskutiert und die Ergebnisse der Anwendung mit verschiedenen Rechenverfahren verglichen und bewertet. Y1 - 2012 U6 - https://doi.org/10.1002/dama.201200537 SN - 1437-1022 (E-Journal); 1432-3427 (Print) VL - 16 IS - 3 SP - 127 EP - 137 PB - Wiley CY - Weinheim ER - TY - JOUR A1 - Butenweg, Christoph A1 - Gellert, Christoph T1 - Integrale Gebäudeplanung am Beispiel eines Geschossbaus in Ziegelmauerwerk JF - Mauerwerk : European journal of masonry N2 - Moderne Mauerwerksbauten müssen nach heutigen Anforderungen architektonisch, statisch, energetisch sowie schall- und brandschutztechnisch optimal ausgelegt sein. Aufgrund der Komplexität und engen Verzahnung der einzelnen Anforderungen ist eine integrale Gebäudeplanung zur Erzielung einer qualitativ hochwertigen Bauwerkslösung unbedingt notwendig. Diese erfordert von den Fachplanern vertieftes Spezialwissen in den verschiedenen Bereichen, um insbesondere die Schnittstellen und Bauwerksdetails korrekt zu planen und auszuführen. Der Beitrag stellt die integrale Gebäudeplanung am Beispiel eines Geschossbaus in Ziegelbauweise mit Lösungen für wesentliche Detailpunkte vor Y1 - 2012 U6 - https://doi.org/10.1002/dama.201200550 SN - 1437-1022 (E-Journal); 1432-3427 (Print) VL - 16 IS - 5 SP - 247 EP - 254 PB - Wiley CY - Weinheim ER - TY - BOOK A1 - Gell, Sebastian T1 - Determinants of earnings forecast error, earnings forecast revision and earnings forecast accuracy N2 - ​Earnings forecasts are ubiquitous in today’s financial markets. They are essential indicators of future firm performance and a starting point for firm valuation. Extremely inaccurate and overoptimistic forecasts during the most recent financial crisis have raised serious doubts regarding the reliability of such forecasts. This thesis therefore investigates new determinants of forecast errors and accuracy. In addition, new determinants of forecast revisions are examined. More specifically, the thesis answers the following questions: 1) How do analyst incentives lead to forecast errors? 2) How do changes in analyst incentives lead to forecast revisions?, and 3) What factors drive differences in forecast accuracy? Y1 - 2012 SN - 978-3-8349-3936-4 SN - 978-3-8349-3937-1 U6 - https://doi.org/10.1007/978-3-8349-3937-1 N1 - Titel in der Buchreihe: Quantitatives Controlling PB - Springer Gabler CY - Wiesbaden ER - TY - JOUR A1 - Butenweg, Christoph A1 - Holtschoppen, Britta T1 - Neuer VCI-Leitfaden für die erdbebensichere Auslegung von Industrieanlagen JF - Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik Y1 - 2012 SN - 1436-4867 (E-Journal); 0005-6650 (Print) VL - 87 SP - 18 PB - VDI Fachmedien CY - Düsseldorf ER - TY - JOUR A1 - Leidinger, Rafael A1 - Noisten, Thomas A1 - Wollert, Jörg T1 - Realtime automation networks in moVing industrial environments JF - Journal of systemics, cybernetics and informatics N2 - The radio-based wireless data communication has made the realization of new technical solutions possible in many fields of the automation technology (AT). For about ten years, a constant disproportionate growth of wireless technologies can be observed in the automation technology. However, it shows that especially for the AT, conventional technologies of office automation are unsuitable and/or not manageable. The employment of mobile services in the industrial automation technology has the potential of significant cost and time savings. This leads to an increased productivity in various fields of the AT, for example in the factory and process automation or in production logistics. In this paper technologies and solutions for an automation-suited supply of mobile wireless services will be introduced under the criteria of real time suitability, IT-security and service orientation. Emphasis will be put on the investigation and development of wireless convergence layers for different radio technologies, on the central provision of support services for an easy-to-use, central, backup enabled management of combined wired / wireless networks and on the study on integrability in a Profinet real-time Ethernet network. KW - PROFINET KW - Distributed Control Systems, KW - Industrial Automation Technology, KW - 802.15.4 KW - Bluetooth KW - Wireless Networks Y1 - 2012 SN - 1690-4532 VL - 10 IS - 2 SP - 52 EP - 56 PB - IIIC CY - Orlando ER - TY - JOUR A1 - Kirchhof, Michael A1 - Kraft, Bodo T1 - Hybrides Vorgehensmodell : Agile und klassische Methoden im Projekt passend kombinieren JF - ProjektMagazin N2 - Agil ist im Trend und immer mehr Unternehmen, die ihre Projekte bisher nach klassischen Prinzipien durchführten, denken über den Einsatz agiler Methoden nach. Doch selbst wenn die Organisation bereits beide Philosophien unterstützt, gilt für ein Projekt meist die klare Vorgabe: agil oder klassisch. Es gibt aber noch einen anderen Ansatz, mit diesen "unterschiedlichen Welten" umzugehen: Und zwar die beiden Philosophien innerhalb eines Projekts zu kombinieren. Wie dies in der Praxis aussehen und gelingen kann, zeigen Dr. Michael Kirchhof und Prof. Dr. Bodo Kraft in diesem Beitrag. Y1 - 2012 IS - 11 PB - Berleb Media CY - Taufkirchen ER - TY - JOUR A1 - Lind, Thorsten Patric T1 - Rechtsprobleme bei der Liquidation der GmbH und der Gewinnausschüttung trotz bestehenden Anspruchs gegen den Gesellschafter : BGH, Urteil vom 23.04.2012 - II ZR 252/10 : Anmerkung JF - Fachdienst Zivilrecht - LMK - Kommentierte BGH-Rechtsprechung, Lindenmaier-Möhring Y1 - 2012 SN - 1611-1095 IS - 10 SP - 338415 PB - Beck CY - München ER -