TY - CHAP A1 - Sattler, Johannes Christoph A1 - Schneider, Iesse Peer A1 - Angele, Florian A1 - Atti, Vikrama A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Development of heliostat field calibration methods: Theory and experimental test results T2 - SolarPACES 2022 conference proceedings N2 - In this work, three patent pending calibration methods for heliostat fields of central receiver systems (CRS) developed by the Solar-Institut Jülich (SIJ) of the FH Aachen University of Applied Sciences are presented. The calibration methods can either operate in a combined mode or in stand-alone mode. The first calibration method, method A, foresees that a camera matrix is placed into the receiver plane where it is subjected to concentrated solar irradiance during a measurement process. The second calibration method, method B, uses an unmanned aerial vehicle (UAV) such as a quadrocopter to automatically fly into the reflected solar irradiance cross-section of one or more heliostats (two variants of method B were tested). The third calibration method, method C, foresees a stereo central camera or multiple stereo cameras installed e.g. on the solar tower whereby the orientations of the heliostats are calculated from the location detection of spherical red markers attached to the heliostats. The most accurate method is method A which has a mean accuracy of 0.17 mrad. The mean accuracy of method B variant 1 is 1.36 mrad and of variant 2 is 1.73 mrad. Method C has a mean accuracy of 15.07 mrad. For method B there is great potential regarding improving the measurement accuracy. For method C the collected data was not sufficient for determining whether or not there is potential for improving the accuracy. KW - Heliostat Field Calibration KW - Unmanned aerial vehicle KW - UAV KW - Quadrocopter KW - Camera system Y1 - 2024 U6 - https://doi.org/10.52825/solarpaces.v1i.678 SN - 2751-9899 (online) N1 - SolarPACES 2022: 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Blanke, Tobias A1 - Schmidt, Katharina S. A1 - Göttsche, Joachim A1 - Döring, Bernd A1 - Frisch, Jérôme A1 - van Treeck, Christoph ED - Weidlich, Anke ED - Neumann, Dirk ED - Gust, Gunther ED - Staudt, Philipp ED - Schäfer, Mirko T1 - Time series aggregation for energy system design: review and extension of modelling seasonal storages T2 - Energy Informatics N2 - Using optimization to design a renewable energy system has become a computationally demanding task as the high temporal fluctuations of demand and supply arise within the considered time series. The aggregation of typical operation periods has become a popular method to reduce effort. These operation periods are modelled independently and cannot interact in most cases. Consequently, seasonal storage is not reproducible. This inability can lead to a significant error, especially for energy systems with a high share of fluctuating renewable energy. The previous paper, “Time series aggregation for energy system design: Modeling seasonal storage”, has developed a seasonal storage model to address this issue. Simultaneously, the paper “Optimal design of multi-energy systems with seasonal storage” has developed a different approach. This paper aims to review these models and extend the first model. The extension is a mathematical reformulation to decrease the number of variables and constraints. Furthermore, it aims to reduce the calculation time while achieving the same results. KW - Energy system KW - Renewable energy KW - Mixed integer linear programming (MILP) KW - Typical periods KW - Time-series aggregation Y1 - 2022 U6 - https://doi.org/10.1186/s42162-022-00208-5 SN - 2520-8942 N1 - 11th DACH+ Conference on Energy Informatics, 15-16 September 2022, Freiburg, Germany VL - 5 IS - 1, Article number: 17 PB - Springer Nature ER - TY - CHAP A1 - Golland, Alexander ED - Taeger, Jürgen ED - Gabel, Detlev T1 - Kommentierung von Artikel 94 bis 99 Datenschutz-Grundverordnung T2 - DSGVO - BDSG - TTDSG: Datenschutzgrundverordnung - Bundesdatenschutzgesetz - Telekommunikation-Telemedien-Datenschutzgesetz N2 - Das Werk kommentiert leicht verständlich, aktuell und praxisnah die DSGVO sowie das BDSG und - neu - auch das TTDSG (Telekommunikation-Telemedien-Datenschutzgesetz). Verantwortliche erhalten damit eine umfassende Darstellung mit Handlungsempfehlungen zum gesamten neuen Datenschutzrecht. Betriebliche Datenschutzbeauftragte können sich an den fundierten Kommentierungen orientieren, in denen Literatur und Rechtsprechung aktuell berücksichtigt wurden. KW - Telekommunikation-Telemedien-Datenschutzgesetz KW - Internationales Recht / Europarecht KW - Datenschutzfolgenabschätzung KW - EU-Datenschutzgrundverordnung KW - Betroffenenrechte Y1 - 2022 SN - 978-3-8005-1760-2 SP - 1575 EP - 1621 PB - Fachmedien Recht und Wirtschaft CY - Frankfurt am Main ET - 4., neu bearbeitete Auflage. 2022 ER - TY - JOUR A1 - Colombo, Daniele A1 - Drira, Slah A1 - Frotscher, Ralf A1 - Staat, Manfred T1 - An element-based formulation for ES-FEM and FS-FEM models for implementation in standard solid mechanics finite element codes for 2D and 3D static analysis JF - International Journal for Numerical Methods in Engineering N2 - Edge-based and face-based smoothed finite element methods (ES-FEM and FS-FEM, respectively) are modified versions of the finite element method allowing to achieve more accurate results and to reduce sensitivity to mesh distortion, at least for linear elements. These properties make the two methods very attractive. However, their implementation in a standard finite element code is nontrivial because it requires heavy and extensive modifications to the code architecture. In this article, we present an element-based formulation of ES-FEM and FS-FEM methods allowing to implement the two methods in a standard finite element code with no modifications to its architecture. Moreover, the element-based formulation permits to easily manage any type of element, especially in 3D models where, to the best of the authors' knowledge, only tetrahedral elements are used in FS-FEM applications found in the literature. Shape functions for non-simplex 3D elements are proposed in order to apply FS-FEM to any standard finite element. KW - distorted element KW - ES-FEM KW - FS-FEM KW - non-simplex S-FEM elements KW - S-FEM Y1 - 2022 U6 - https://doi.org/10.1002/nme.7126 SN - 1097-0207 VL - 124 IS - 2 SP - 402 EP - 433 PB - Wiley CY - Chichester ER - TY - CHAP A1 - Hinke, Christian A1 - Vervier, Luisa A1 - Brauner, Philipp A1 - Schneider, Sebastian A1 - Steuer-Dankert, Linda A1 - Ziefle, Martina A1 - Leicht-Scholten, Carmen T1 - Capability configuration in next generation manufacturing T2 - Forecasting next generation manufacturing : digital shadows, human-machine collaboration, and data-driven business models N2 - Industrial production systems are facing radical change in multiple dimensions. This change is caused by technological developments and the digital transformation of production, as well as the call for political and social change to facilitate a transformation toward sustainability. These changes affect both the capabilities of production systems and companies and the design of higher education and educational programs. Given the high uncertainty in the likelihood of occurrence and the technical, economic, and societal impacts of these concepts, we conducted a technology foresight study, in the form of a real-time Delphi analysis, to derive reliable future scenarios featuring the next generation of manufacturing systems. This chapter presents the capabilities dimension and describes each projection in detail, offering current case study examples and discussing related research, as well as implications for policy makers and firms. Specifically, we discuss the benefits of capturing expert knowledge and making it accessible to newcomers, especially in highly specialized industries. The experts argue that in order to cope with the challenges and circumstances of today’s world, students must already during their education at university learn how to work with AI and other technologies. This means that study programs must change and that universities must adapt their structural aspects to meet the needs of the students. Y1 - 2022 SN - 978-3-031-07733-3 U6 - https://doi.org/10.1007/978-3-031-07734-0_6 SP - 95 EP - 106 PB - Springer CY - Cham ER - TY - JOUR A1 - Morandi, Paolo A1 - Butenweg, Christoph A1 - Breis, Khaled A1 - Beyer, Katrin A1 - Magenes, Guido ED - Ansal, Atilla T1 - Latest findings on the behaviour factor q for the seismic design of URM buildings JF - Bulletin of Earthquake Engineering N2 - Recent earthquakes as the 2012 Emilia earthquake sequence showed that recently built unreinforced masonry (URM) buildings behaved much better than expected and sustained, despite the maximum PGA values ranged between 0.20–0.30 g, either minor damage or structural damage that is deemed repairable. Especially low-rise residential and commercial masonry buildings with a code-conforming seismic design and detailing behaved in general very well without substantial damages. The low damage grades of modern masonry buildings that was observed during this earthquake series highlighted again that codified design procedures based on linear analysis can be rather conservative. Although advances in simulation tools make nonlinear calculation methods more readily accessible to designers, linear analyses will still be the standard design method for years to come. The present paper aims to improve the linear seismic design method by providing a proper definition of the q-factor of URM buildings. These q-factors are derived for low-rise URM buildings with rigid diaphragms which represent recent construction practise in low to moderate seismic areas of Italy and Germany. The behaviour factor components for deformation and energy dissipation capacity and for overstrength due to the redistribution of forces are derived by means of pushover analyses. Furthermore, considerations on the behaviour factor component due to other sources of overstrength in masonry buildings are presented. As a result of the investigations, rationally based values of the behaviour factor q to be used in linear analyses in the range of 2.0–3.0 are proposed. KW - Unreinforced masonry buildings KW - Modern constructions KW - Seismic design KW - Linear elastic analysis KW - Behaviour factor q Y1 - 2022 U6 - https://doi.org/10.1007/s10518-022-01419-7 SN - 1573-1456 SN - 1570-761X VL - 20 IS - 11 SP - 5797 EP - 5848 PB - Springer Nature CY - Cham ER - TY - CHAP A1 - Allal, D. A1 - Bannister, R. A1 - Buisman, K. A1 - Capriglione, D. A1 - Di Capua, G. A1 - García-Patrón, M. A1 - Gatzweiler, Thomas A1 - Gellersen, F. A1 - Harzheim, Thomas A1 - Heuermann, Holger A1 - Hoffmann, J. A1 - Izbrodin, A. A1 - Kuhlmann, K. A1 - Lahbacha, K. A1 - Maffucci, A. A1 - Miele, G. A1 - Mubarak, F. A1 - Salter, M. A1 - Pham, T.D. A1 - Sayegh, A. A1 - Singh, D. A1 - Stein, F. A1 - Zeier, M. T1 - RF measurements for future communication applications: an overview T2 - 2022 IEEE International Symposium on Measurements & Networking (M&N) N2 - In this paper research activities developed within the FutureCom project are presented. The project, funded by the European Metrology Programme for Innovation and Research (EMPIR), aims at evaluating and characterizing: (i) active devices, (ii) signal- and power integrity of field programmable gate array (FPGA) circuits, (iii) operational performance of electronic circuits in real-world and harsh environments (e.g. below and above ambient temperatures and at different levels of humidity), (iv) passive inter-modulation (PIM) in communication systems considering different values of temperature and humidity corresponding to the typical operating conditions that we can experience in real-world scenarios. An overview of the FutureCom project is provided here, then the research activities are described. KW - FPGA KW - signal integrity KW - power integrity KW - passive inter-modulation KW - metrological characterization Y1 - 2022 SN - 978-1-6654-8362-9 SN - 978-1-6654-8363-6 U6 - https://doi.org/10.1109/MN55117.2022.9887740 SN - 2639-5061 SN - 2639-507X N1 - 2022 IEEE International Symposium on Measurements & Networking (M&N), 18-20 July 2022, Padua, Italy. SP - 1 EP - 6 PB - IEEE ER - TY - JOUR A1 - Peere, Wouter A1 - Blanke, Tobias ED - Vernon, Chris T1 - GHEtool: An open-source tool for borefield sizing in Python JF - Journal of Open Source Software N2 - GHEtool is a Python package that contains all the functionalities needed to deal with borefield design. It is developed for both researchers and practitioners. The core of this package is the automated sizing of borefield under different conditions. The sizing of a borefield is typically slow due to the high complexity of the mathematical background. Because this tool has a lot of precalculated data, GHEtool can size a borefield in the order of tenths of milliseconds. This sizing typically takes the order of minutes. Therefore, this tool is suited for being implemented in typical workflows where iterations are required. GHEtool also comes with a graphical user interface (GUI). This GUI is prebuilt as an exe-file because this provides access to all the functionalities without coding. A setup to install the GUI at the user-defined place is also implemented and available at: https://www.mech.kuleuven.be/en/tme/research/thermal_systems/tools/ghetool. KW - geothermal KW - energy KW - borefields KW - sizing Y1 - 2022 U6 - https://doi.org/10.21105/joss.04406 SN - 2475-9066 VL - 7 IS - 76 SP - 1 EP - 4, 4406 ER - TY - THES A1 - Larscheid, Maja Marlene T1 - The Future of Fitness : Konzeption und Gestaltung einer digitalen Fitness- und Gesundheitsanwendung N2 - Laut einer Langzeitstudie bewegt sich mehr als ein Viertel der Weltbevölkerung – rund 2 Milliarden Menschen – zu wenig. Trotzdem ließ sich zuletzt klares Interesse an Fitness- und Gesundheitsmöglichkeiten am stetigen Anstieg der Fitnessstudio-Mitgliederzahl erkennen. Nachdem die Zahl seit 2006 jedes Jahr anstieg, fiel sie in den Pandemie-Jahren. Seit der Pandemie besteht also Bedarf nach einer flexibleren Lösung zu klassischen Studios. Um diesen Bedarf zu decken, wurde eine digitale Lösung zum Thema entwickelt. Dazu wurden Sport und Ernährung zusammengefasst. Das beinhaltet Videoanleitungen, Ernährungs- und Trainingsplanerstellung, individuelle Körperanalyse im Onboarding-Prozess, Verbindung mit Wearables und ein flexibles Online- sowie Studioangebot. Meine Zielgruppe sind Menschen, die flexibel Sport machen, mit Sport anfangen oder ihre allgemeine Gesundheit verbessern wollen. KW - Fitness KW - Gesundheit KW - Ernährung KW - Sport KW - UXDesign Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Schwager, Christian A1 - Angele, Florian A1 - Nouri, Bijan A1 - Schwarzbözl, Peter A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Impact of DNI forecast quality on performance prediction for a commercial scale solar tower: Application of nowcasting DNI maps to dynamic solar tower simulation T2 - SolarPACES 2022 conference proceedings N2 - Concerning current efforts to improve operational efficiency and to lower overall costs of concentrating solar power (CSP) plants with prediction-based algorithms, this study investigates the quality and uncertainty of nowcasting data regarding the implications for process predictions. DNI (direct normal irradiation) maps from an all-sky imager-based nowcasting system are applied to a dynamic prediction model coupled with ray tracing. The results underline the need for high-resolution DNI maps in order to predict net yield and receiver outlet temperature realistically. Furthermore, based on a statistical uncertainty analysis, a correlation is developed, which allows for predicting the uncertainty of the net power prediction based on the corresponding DNI forecast uncertainty. However, the study reveals significant prediction errors and the demand for further improvement in the accuracy at which local shadings are forecasted. KW - Process prediction KW - DNI forecasting KW - Nowcasting KW - Uncertainty analysis KW - Molten salt receiver system, Y1 - 2024 U6 - https://doi.org/10.52825/solarpaces.v1i.675 SN - 2751-9899 (online) N1 - SolarPACES 2022, 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Schulte, Jonas A1 - Schwager, Christian A1 - Frantz, Cathy A1 - Schloms, Felix A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Control concept for a molten salt receiver in star design: Development, optimization and testing with cloud passage scenarios T2 - SolarPACES 2022 conference proceedings N2 - A promising approach to reduce the system costs of molten salt solar receivers is to enable the irradiation of the absorber tubes on both sides. The star design is an innovative receiver design, pursuing this approach. The unconventional design leads to new challenges in controlling the system. This paper presents a control concept for a molten salt receiver system in star design. The control parameters are optimized in a defined test cycle by minimizing a cost function. The control concept is tested in realistic cloud passage scenarios based on real weather data. During these tests, the control system showed no sign of unstable behavior, but to perform sufficiently in every scenario further research and development like integrating Model Predictive Controls (MPCs) need to be done. The presented concept is a starting point to do so. KW - Molten salt receiver KW - Star design KW - Control optimization KW - Cloud passages Y1 - 2023 U6 - https://doi.org/10.52825/solarpaces.v1i.693 SN - 2751-9899 (online) N1 - SolarPACES 2022, 28th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27-30 September, Albuquerque, NM, USA IS - 1 PB - TIB Open Publishing CY - Hannover ER - TY - CHAP A1 - Striebing, Clemens A1 - Müller, Jörg A1 - Schraudner, Martina A1 - Gewinner, Irina Valerie A1 - Guerrero Morales, Patricia A1 - Hochfeld, Katharina A1 - Hoffman, Shekinah A1 - Kmec, Julie A. A1 - Nguyen, Huu Minh A1 - Schneider, Jannick A1 - Sheridan, Jennifer A1 - Steuer-Dankert, Linda A1 - Trimble O'Connor, Lindsey A1 - Vandevelde-Rougale, Agnès T1 - Promoting diversity and combatting discrimination in research organizations: a practitioner’s guide T2 - Diversity and discrimination in research organizations N2 - The essay is addressed to practitioners in research management and from academic leadership. It describes which measures can contribute to creating an inclusive climate for research teams and preventing and effectively dealing with discrimination. The practical recommendations consider the policy and organizational levels, as well as the individual perspective of research managers. Following a series of basic recommendations, six lessons learned are formulated, derived from the contributions to the edited collection on “Diversity and Discrimination in Research Organizations.” KW - Inclusive work climate KW - lessons learned KW - policy recommendations KW - recommendations for actions KW - bullying Y1 - 2022 SN - 978-1-80117-959-1 (Print) SN - 978-1-80117-956-0 (Online) U6 - https://doi.org/10.1108/978-1-80117-956-020221012 SP - 421 EP - 442 PB - Emerald Publishing Limited CY - Bingley ER - TY - GEN A1 - Steuer-Dankert, Linda A1 - Bernhard, Sebastian A1 - Langolf, Jessica A1 - Leicht-Scholten, Carmen T1 - Managing change and acceptance of digitalization strategies - Implementing the vision of „Internet of Production“ (IoP) in existing corporate structures T2 - Textile Impulse für die Zukunft: Aachen-Dresden-Denkendorf International Textile Conference 2022 N2 - The vision of the Internet of Production is to enable a new level of crossdomain collaboration by providing semantically adequate and context-aware data from production, development & usage in real-time. Y1 - 2022 N1 - Textile Impulse für die Zukunft: Aachen-Dresden-Denkendorf International Textile Conference 2022 : 1. – 2. Dezember 2022, Eurogress Aachen SP - 153 EP - 153 ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Leicht-Scholten, Carmen T1 - Perceiving diversity : an explorative approach in a complex research organization. T2 - Diversity and discrimination in research organizations N2 - Diversity management is seen as a decisive factor for ensuring the development of socially responsible innovations (Beacham and Shambaugh, 2011; Sonntag, 2014; López, 2015; Uebernickel et al., 2015). However, many diversity management approaches fail due to a one-sided consideration of diversity (Thomas and Ely, 2019) and a lacking linkage between the prevailing organizational culture and the perception of diversity in the respective organization. Reflecting the importance of diverse perspectives, research institutions have a special responsibility to actively deal with diversity, as they are publicly funded institutions that drive socially relevant development and educate future generations of developers, leaders and decision-makers. Nevertheless, only a few studies have so far dealt with the influence of the special framework conditions of the science system on diversity management. Focusing on the interdependency of the organizational culture and diversity management especially in a university research environment, this chapter aims in a first step to provide a theoretical perspective on the framework conditions of a complex research organization in Germany in order to understand the system-specific factors influencing diversity management. In a second step, an exploratory cluster analysis is presented, investigating the perception of diversity and possible influencing factors moderating this perception in a scientific organization. Combining both steps, the results show specific mechanisms and structures of the university research environment that have an impact on diversity management and rigidify structural barriers preventing an increase of diversity. The quantitative study also points out that the management level takes on a special role model function in the scientific system and thus has an influence on the perception of diversity. Consequently, when developing diversity management approaches in research organizations, it is necessary to consider the top-down direction of action, the special nature of organizational structures in the university research environment as well as the special role of the professorial level as role model for the scientific staff. KW - Diversity management KW - Organizational culture KW - Change management KW - Psychological concepts KW - Perception Y1 - 2022 SN - 978-1-80117-959-1 (Print) SN - 978-1-80117-956-0 (Online) U6 - https://doi.org/10.1108/978-1-80117-956-020221010 SP - 365 EP - 392 PB - Emerald Publishing Limited CY - Bingley ER - TY - CHAP A1 - Chico Caminos, Ricardo Alexander A1 - Schmitz, Pascal A1 - Atti, Vikrama A1 - Mahdi, Zahra A1 - Teixeira Boura, Cristiano José A1 - Sattler, Johannes Christoph A1 - Herrmann, Ulf A1 - Hilger, Patrick A1 - Dieckmann, Simon T1 - Development of a micro heliostat and optical qualification assessment with a 3D laser scanning method T2 - SOLARPACES 2020 N2 - The Solar-Institut Jülich (SIJ) and the companies Hilger GmbH and Heliokon GmbH from Germany have developed a small-scale cost-effective heliostat, called “micro heliostat”. Micro heliostats can be deployed in small-scale concentrated solar power (CSP) plants to concentrate the sun's radiation for electricity generation, space or domestic water heating or industrial process heat. In contrast to conventional heliostats, the special feature of a micro heliostat is that it consists of dozens of parallel-moving, interconnected, rotatable mirror facets. The mirror facets array is fixed inside a box-shaped module and is protected from weathering and wind forces by a transparent glass cover. The choice of the building materials for the box, tracking mechanism and mirrors is largely dependent on the selected production process and the intended application of the micro heliostat. Special attention was paid to the material of the tracking mechanism as this has a direct influence on the accuracy of the micro heliostat. The choice of materials for the mirror support structure and the tracking mechanism is made in favor of plastic molded parts. A qualification assessment method has been developed by the SIJ in which a 3D laser scanner is used in combination with a coordinate measuring machine (CMM). For the validation of this assessment method, a single mirror facet was scanned and the slope deviation was computed. KW - Concentrated solar power KW - Electricity generation KW - Measuring instruments KW - Heliostats KW - Global change Y1 - 2022 SN - 978-0-7354-4195-8 U6 - https://doi.org/10.1063/5.0086262 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September–2 October 2020, Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - THES A1 - Treutlein, Antonia T1 - Entwicklung eines Erscheinungsbildes für die Meeresschutzorganisation Ocean Care N2 - Ocean Care ist eine politisch unabhängige Non-Profit-Organisation mit Sitz in der Schweiz. Sie setzt sich seit 1989 für den Schutz von Meeressäugern und deren Lebensraum ein. Seit 2011 ist Ocean Care außerdem UN-Sonderberaterin für Fragen im Meeresschutz. Da Ocean Care die Öffentlichkeit für das Thema Meeresschutz sensibilisieren möchte und ihre Arbeit durch Spenden finanziert wird, ist ein professionelles, vertrauenerweckendes Erscheinungsbild unerlässlich. Durch ein zeitgemäßes und seriöses Design, welches sich von anderen Organisationen abhebt, kann die Zielgruppe erweitert und die Bedeutsamkeit der Arbeit hervorgehoben werden. Das neue Erscheinungsbild beruht auf der Idee, dass sich die Informationen unter der Meeresoberfläche befinden. Die Linie, die den Meeresspiegel visualisiert, dient außerdem medienübergreifend als Orientierungshilfe. KW - Erscheinungsbild KW - Gestaltung KW - Corporate Design KW - Layout KW - Redesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Mertens, Alexander A1 - Brauner, Philipp A1 - Baier, Ralph A1 - Brillowski, Florian A1 - Dammers, Hannah A1 - van Dyck, Marc A1 - Kong, Iris A1 - Königs, Peter A1 - Kordtomeikel, Frauke A1 - Liehner, Gian Luca A1 - Pütz, Sebastian A1 - Rodermann, Niklas A1 - Schaar, Anne Kathrin A1 - Steuer-Dankert, Linda A1 - Vervier, Luisa A1 - Wlecke, Shari A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Nagel, Saskia K. A1 - Piller, Frank T. A1 - Schuh, Günther A1 - Ziefle, Martina A1 - Nitsch, Verena ED - Michael, Judith ED - Pfeiffer, Jérôme ED - Wortmann, Andreas T1 - Modelling Human Factors in Cyber Physical Production Systems by the Integration of Human Digital Shadows T2 - Modellierung 2022 Satellite Events N2 - The future of industrial manufacturing and production will increasingly manifest in the form of cyber-physical production systems. Here, Digital Shadows will act as mediators between the physical and digital world to model and operationalize the interactions and relationships between different entities in production systems. Until now, the associated concepts have been primarily pursued and implemented from a technocentric perspective, in which human actors play a subordinate role, if they are considered at all. This paper outlines an anthropocentric approach that explicitly considers the characteristics, behavior, and traits and states of human actors in socio-technical production systems. For this purpose, we discuss the potentials and the expected challenges and threats of creating and using Human Digital Shadows in production. KW - human digital shadow KW - cyber physical production system KW - human factors Y1 - 2022 U6 - https://doi.org/10.18420/modellierung2022ws-018 N1 - Modellierung 2022, 27. Juni - 01. Juli 2022, Hamburg, Deutschland SP - 147 EP - 149 PB - GI Gesellschaft für Informatik CY - Bonn ER - TY - BOOK A1 - Bundrock, Ronja A1 - Kremers, Nico A1 - Pankok, Lennard A1 - Weisheit, Theresa Maria A1 - Spoede, Jasper ED - Kroll-Ludwigs, Kathrin ED - Bernecker, Andreas ED - Bassen-Metz, Yasmine ED - Eggert, Mathias ED - Fritz, Thomas ED - Golland, Alexander ED - Höhne, Tim ED - Tran, Duc Hung ED - Vogt, Jürgen T1 - Aachener Online-Schriften Wirtschaft und Recht. Band 5. 02/2022 N2 - Inhaltsverzeichnis - Bachelorarbeiten 1. Testamentsgestaltung bei Patchworkfamilien – Lösungsansätze für typische Praxisprobleme unter Berücksichtigung der Interessenlagen der Parteien - Ronja Bundrock 4 - 58 2. Die Haftung des AG-Vorstands gegenüber der Gesellschaft in unterneh- mensinternen und -externen Krisen - Nico Kremers 59 - 122 3. The Relationship of the Ex-Ante Uncertainty about the Value of a Stock and its IPO Underpricing – An Analysis of the German Market - Lennard Pankok 123 - 179 4. Attractiveness Bias in Venture Capital – An Analysis of Investor Decision Making in “Die Höhle der Löwen” - Theresa Maria Weisheit 180 - 242 Inhaltsverzeichnis – Masterarbeiten Erhöhung der Energieautarkie in der Backbranche – Anwendung von bidi- rektionalem Laden und dessen Auswirkungen auf die Geschäftsprozesse und Informationssysteme - Jasper Spoede 243 - 355 T3 - Aachener Online-Schriften Wirtschaft und Recht - 5 Y1 - 2022 PB - FH Aachen / Fachbereich Wirtschaftswissenschaften CY - Aachen ER - TY - THES A1 - Koscielniak, Luise T1 - Das Ludwig Forum Aachen : die Erstellung eines neuen Erscheinungsbildes N2 - Peter und Irene Ludwig galten als das Kunstsammlerpaar Deutschlands. Sie stellten ihre umfangreiche Sammlung der Öffentlichkeit zur Verfügung, so auch dem Ludwig Forum - das Stammmuseum der beiden Aachener. Doch es ist viel mehr als nur ein Museum. Der Gedanke des Forums als einen Ort des Austausches und der Kommunikation mit und über Kunst ist die leittragende Idee. Das neue Erscheinungsbild leitet sich in der Gestaltung bildlich von diesem Forumsgedanken ab. Zur Visualisierung dieser Idee wurden Kommunikationsachsen aufgegriffen, die zur typografischen Ausrichtung genutzt werden. Sie bieten die Möglichkeit, in verschiedene Richtungen zu kommunizieren und Inhalte vielseitig und prägnant zu visualisieren. Die Wortmarke des Ludwig Forums dient dabei als klammerndes Element, welches den Rahmen für die Gestaltung ermöglichen. Mit der Fokussierung auf den Forumsgedanken setzt sich das Ludwig Forum sowohl inhaltlich als nun auch gestalterisch von anderen Museumseinrichtungen ab. KW - Erscheinungsbild KW - Ludwig Forum KW - Forum KW - Kommunikation KW - Dialog Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Eigel, Nick T1 - uCo - the universal communicator : robotische Konversationen unserer Zukunft N2 - Kommunikationsroboter für den Kundenservice. Aktuell werden große Fortschritte im Bereich von künstlicher Intelligenz und Robotik getätigt, sodass wir bald intelligente Maschinen unter uns haben werden. Daher müssen wir uns die Frage beantworten, welche Rolle diese einnehmen sollen und vor allem wie wir mit ihnen interagieren und kommunizieren wollen. "uCo" bewältigt dies mithilfe einer mobilen, robotischen Plattform, welche mit einem holografischen 3-D-Interface ausgestattet ist. Neben der Entwicklung des robotischen Körpers beinhaltet das Projekt "uCo" die Grundlage für ein Kommunikationssystem für "uCo's" Gesicht. "uCo" kommuniziert hauptsächlich über Sprache, wird dabei jedoch von einem speziell entwickelten Mimik- und Emotionssytem unterstützt. "uCo" als Konzept versucht, erste Antworten auf die komplexen gestalterischen und moralischen Fragen zu geben, die mit der Entwicklung von künstlicher Intelligenz einhergehen. Und wer weiß - vielleicht wirst du eines Tages von einem "uCo" beraten. KW - Robotik KW - Hologram KW - Kommunikation KW - künstliche Intelligenz KW - KI Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Schwager, Christian A1 - Flesch, Robert A1 - Schwarzbözl, Peter A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José T1 - Advanced two phase flow model for transient molten salt receiver system simulation JF - Solar Energy N2 - In order to realistically predict and optimize the actual performance of a concentrating solar power (CSP) plant sophisticated simulation models and methods are required. This paper presents a detailed dynamic simulation model for a Molten Salt Solar Tower (MST) system, which is capable of simulating transient operation including detailed startup and shutdown procedures including drainage and refill. For appropriate representation of the transient behavior of the receiver as well as replication of local bulk and surface temperatures a discretized receiver model based on a novel homogeneous two-phase (2P) flow modelling approach is implemented in Modelica Dymola®. This allows for reasonable representation of the very different hydraulic and thermal properties of molten salt versus air as well as the transition between both. This dynamic 2P receiver model is embedded in a comprehensive one-dimensional model of a commercial scale MST system and coupled with a transient receiver flux density distribution from raytracing based heliostat field simulation. This enables for detailed process prediction with reasonable computational effort, while providing data such as local salt film and wall temperatures, realistic control behavior as well as net performance of the overall system. Besides a model description, this paper presents some results of a validation as well as the simulation of a complete startup procedure. Finally, a study on numerical simulation performance and grid dependencies is presented and discussed. KW - Molten salt solar tower KW - Molten salt receiver system KW - Dynamic simulation KW - Two-phase modelling KW - Transient flux distribution Y1 - 2022 U6 - https://doi.org/10.1016/j.solener.2021.12.065 SN - 0038-092X (print) SN - 1471-1257 (online) VL - 232 SP - 362 EP - 375 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Bhattarai, Aroj A1 - May, Charlotte Anabell A1 - Staat, Manfred A1 - Kowalczyk, Wojciech A1 - Tran, Thanh Ngoc T1 - Layer-specific damage modeling of porcine large intestine under biaxial tension JF - Bioengineering N2 - The mechanical behavior of the large intestine beyond the ultimate stress has never been investigated. Stretching beyond the ultimate stress may drastically impair the tissue microstructure, which consequently weakens its healthy state functions of absorption, temporary storage, and transportation for defecation. Due to closely similar microstructure and function with humans, biaxial tensile experiments on the porcine large intestine have been performed in this study. In this paper, we report hyperelastic characterization of the large intestine based on experiments in 102 specimens. We also report the theoretical analysis of the experimental results, including an exponential damage evolution function. The fracture energies and the threshold stresses are set as damage material parameters for the longitudinal muscular, the circumferential muscular and the submucosal collagenous layers. A biaxial tensile simulation of a linear brick element has been performed to validate the applicability of the estimated material parameters. The model successfully simulates the biomechanical response of the large intestine under physiological and non-physiological loads. KW - biaxial tensile experiment KW - anisotropy KW - hyperelastic KW - constitutive modeling KW - damage Y1 - 2022 U6 - https://doi.org/10.3390/bioengineering9100528 SN - 2306-5354 N1 - Der Artikel gehört zum Sonderheft "Computational Biomechanics" VL - 9 IS - 10, Early Access SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - BOOK A1 - Blöcker, Lene Christin A1 - Esser, Julia A1 - Hengstebeck, Pauline A1 - Venrath, Carolin A1 - Scholtes, Eva ED - Kroll-Ludwigs, Kathrin ED - Bernecker, Andreas ED - Bassen-Metz, Yasmine ED - Eggert, Mathias ED - Fritz, Thomas ED - Golland, Alexander ED - Höhne, Tim ED - Tran, Duc Hung ED - Vogt, Jürgen T1 - Aachener Online-Schriften Wirtschaft und Recht. Band 4. 01/2022 N2 - Inhaltsverzeichnis - Bachelorarbeiten 1. The impact of the EU non-financial reporting directive on sustainability reporting practices of DAX 30 companies - Lene Christin Blöcker 4 - 29 2. Kurzarbeit als Krisenbewältigungsinstrument – Die arbeitsrechtlichen Voraussetzungen für die wirksame Einführung von Kurzarbeit - Julia Esser 30 - 87 3. Die virtuelle Hauptversammlung der Aktiengesellschaft – Notlösung während der Corona-Pandemie oder dauerhafte Alternative? - Pauline Hengstebeck 88 - 152 4. Die psychische Gesundheit am Arbeitsplatz – Aktuelle Problematik, Ursachenforschung, Folgen, rechtliche Rahmenbedingungen und geeignete Präventionsmaßnahmen aus Arbeitgebersicht - Carolin Venrath 153 - 224 Inhaltsverzeichnis – Masterarbeiten The influence of religion on the representation of women in politics - Eva Scholtes 225 - 345 T3 - Aachener Online-Schriften Wirtschaft und Recht - 4 Y1 - 2022 PB - FH Aachen / Fachbereich Wirtschaftswissenschaften CY - Aachen ER - TY - THES A1 - Roentgen, Matthis T1 - Ketten, die die Welt umspannen : wie funktioniert Blockchain-Technologie und was kann sie uns bieten? N2 - Bitcoins und NFTs sind längst keine Neuheit mehr und vielen bereits ein Begriff. Doch was genau steckt hinter digitalen Währungen und kryptografischen Tokens? »Ketten, die die Welt umspannen« ist die erste Ausgabe des »101.mag« und setzt sich mit dieser Frage auseinander. Das Magazin versucht über ein unkonventionelles Layout, interessante Artikel und spannende Illustrationen seine Leser:innen in die Welt der vielversprechenden Technologie einzuführen. Die Kommunikationen zwischen Mensch und Computer steht nicht nur thematisch im Mittelpunkt dieser Arbeit. Auch die Gestaltung profitiert von dieser Zusammenarbeit. So wurde der Fließtext mithilfe eines Processing-Tools über das Raster verteilt. Auch die Illustration wurde über ein weiteres Programm in verpixelte Grafiken umgewandelt. Die statischen Bild- und Textelemente werden durch kleine Animationen ergänzt. Diese werden im digitalen Raum eingesetzt und unterstützen so das gesamte Konzept auf multimedialer Ebene. Das Ergebnis ist ein besonderes Magazin, welches eine neue Richtung einschlägt. KW - Editorial KW - generische Gestaltung KW - Layout KW - Magazin KW - Blockchain Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Nordmann, Alexander T1 - Prozessüberwachung beim Werkzeugschleifen von WC-Co Hartmetallschaftfräsern Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Vu, Tuan Dat T1 - Objekterkennung und Schienenerkennung in der Schienenfahrzeugtechnik Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Alt, Helmut T1 - Speicher speichern, Leiter leiten T2 - Generationenprojekt Energiewende : Elektroenergiepolitik im Spannungsfeld zwischen Vision und Mission / Herbert Niederhausen (Hrsg.) Y1 - 2022 SN - 9783755774389 N1 - gedruckt in der Bereichsbibliothek Eupener Str. unter der Signatur 21 ZPM 4 SP - 125 EP - 136 PB - Books on Demand CY - Norderstedt ER - TY - CHAP A1 - Büsgen, André A1 - Klöser, Lars A1 - Kohl, Philipp A1 - Schmidts, Oliver A1 - Kraft, Bodo A1 - Zündorf, Albert T1 - Exploratory analysis of chat-based black market profiles with natural language processing T2 - Proceedings of the 11th International Conference on Data Science, Technology and Applications N2 - Messenger apps like WhatsApp or Telegram are an integral part of daily communication. Besides the various positive effects, those services extend the operating range of criminals. Open trading groups with many thousand participants emerged on Telegram. Law enforcement agencies monitor suspicious users in such chat rooms. This research shows that text analysis, based on natural language processing, facilitates this through a meaningful domain overview and detailed investigations. We crawled a corpus from such self-proclaimed black markets and annotated five attribute types products, money, payment methods, user names, and locations. Based on each message a user sends, we extract and group these attributes to build profiles. Then, we build features to cluster the profiles. Pretrained word vectors yield better unsupervised clustering results than current state-of-the-art transformer models. The result is a semantically meaningful high-level overview of the user landscape of black market chatrooms. Additionally, the extracted structured information serves as a foundation for further data exploration, for example, the most active users or preferred payment methods. KW - Clustering KW - Natural Language Processing KW - Information Extraction KW - Profile Extraction KW - Text Mining Y1 - 2022 SN - 978-989-758-583-8 U6 - https://doi.org/10.5220/0011271400003269 SN - 2184-285X N1 - 11th International Conference on Data Science, Technology and Applications DATA - Volume 1, 83-94, 2022, Lisbon, Portugal SP - 83 EP - 94 ER - TY - CHAP A1 - Ostkotte, Sebastian A1 - Peters, Constantin A1 - Hüning, Felix A1 - Bragard, Michael T1 - Design, implementation and verification of an rotational incremental position encoder based on the magnetic Wiegand effect T2 - 2022 ELEKTRO (ELEKTRO) N2 - This paper covers the use of the magnetic Wiegand effect to design an innovative incremental encoder. First, a theoretical design is given, followed by an estimation of the achievable accuracy and an optimization in open-loop operation. Finally, a successful experimental verification is presented. For this purpose, a permanent magnet synchronous machine is controlled in a field-oriented manner, using the angle information of the prototype. KW - Position Encoder KW - Rotational Encoder KW - Wiegand Effect KW - Angle Sensor KW - Incremental Encoder Y1 - 2022 SN - 978-1-6654-6726-1 SN - 978-1-6654-6727-8 U6 - https://doi.org/10.1109/ELEKTRO53996.2022.9803477 SN - 2691-0616 N1 - 2022 ELEKTRO (ELEKTRO), 23-26 Mai 2022, Krakow, Poland. PB - IEEE ER - TY - BOOK A1 - Engelmann, Ulrich M. T1 - Zielführend moderieren N2 - In der Teamarbeit wird Moderation zum Erfolgsfaktor, der jedoch häufig unterschätzt wird. Ausgehend vom persönlichen Kompetenzniveau verknüpft dieses Buch Grundlagen und Methoden zu Wegen, um Ihre persönliche Entwicklung individuell zu begleiten: Neulinge finden hilfreiche Checklisten und Basistechniken für ihre ersten Moderationen, Fortgeschrittene wertvolle Praxistipps und Methoden für den Ausbau ihrer Moderationskompetenz. Profis schließlich genießen eine raffinierte Aussicht auf weniger bekannte Techniken und neue Anwendungen. Weiterführende Exkurse zum Meeting-Management und zur Online-Moderation runden den Anwendungshorizont ab. Ob in Beruf, Studium oder Ehrenamt – derart ausgestattet gelingen Ihre eigene sowie die Entwicklung Ihres Teams durch zielführende Moderationen. Y1 - 2022 SN - 9783838556895 U6 - https://doi.org/10.36198/9783838556895 PB - UVK Verlag CY - Stuttgart ER - TY - JOUR A1 - Mandekar, Swati A1 - Holland, Abigail A1 - Thielen, Moritz A1 - Behbahani, Mehdi A1 - Melnykowycz, Mark T1 - Advancing towards Ubiquitous EEG, Correlation of In-Ear EEG with Forehead EEG JF - Sensors N2 - Wearable EEG has gained popularity in recent years driven by promising uses outside of clinics and research. The ubiquitous application of continuous EEG requires unobtrusive form-factors that are easily acceptable by the end-users. In this progression, wearable EEG systems have been moving from full scalp to forehead and recently to the ear. The aim of this study is to demonstrate that emerging ear-EEG provides similar impedance and signal properties as established forehead EEG. EEG data using eyes-open and closed alpha paradigm were acquired from ten healthy subjects using generic earpieces fitted with three custom-made electrodes and a forehead electrode (at Fpx) after impedance analysis. Inter-subject variability in in-ear electrode impedance ranged from 20 kΩ to 25 kΩ at 10 Hz. Signal quality was comparable with an SNR of 6 for in-ear and 8 for forehead electrodes. Alpha attenuation was significant during the eyes-open condition in all in-ear electrodes, and it followed the structure of power spectral density plots of forehead electrodes, with the Pearson correlation coefficient of 0.92 between in-ear locations ELE (Left Ear Superior) and ERE (Right Ear Superior) and forehead locations, Fp1 and Fp2, respectively. The results indicate that in-ear EEG is an unobtrusive alternative in terms of impedance, signal properties and information content to established forehead EEG. KW - in-ear EEG KW - correlation KW - forehead EEG KW - impedance spectroscopy KW - biopotential electrodes Y1 - 2022 U6 - https://doi.org/10.3390/s22041568 SN - 1424-8220 VL - 22 IS - 4 SP - 1 EP - 19 PB - MDPI CY - Basel ER - TY - JOUR A1 - Maurischat, Andreas T1 - Algebraic independence of the Carlitz period and its hyperderivatives JF - Journal of Number Theory KW - Drinfeld modules KW - Periods KW - t-modules KW - Transcendence KW - Higher derivations Y1 - 2022 U6 - https://doi.org/10.1016/j.jnt.2022.01.006 SN - 0022-314X VL - 240 SP - 145 EP - 162 PB - Elsevier CY - Orlando, Fla. ER - TY - JOUR A1 - Schüller-Ruhl, Aaron A1 - Dinstühler, Leonard A1 - Senger, Thorsten A1 - Bergfeld, Stefan A1 - Ingenhag, Christian A1 - Fleischhaker, Robert ED - Mackenzie, Jacob T1 - Direct fabrication of arbitrary phase masks in optical glass via ultra-short pulsed laser writing of refractive index modifications JF - Applied Physics B N2 - We study the possibility to fabricate an arbitrary phase mask in a one-step laser-writing process inside the volume of an optical glass substrate. We derive the phase mask from a Gerchberg–Saxton-type algorithm as an array and create each individual phase shift using a refractive index modification of variable axial length. We realize the variable axial length by superimposing refractive index modifications induced by an ultra-short pulsed laser at different focusing depth. Each single modification is created by applying 1000 pulses with 15 μJ pulse energy at 100 kHz to a fixed spot of 25 μm diameter and the focus is then shifted axially in steps of 10 μm. With several proof-of-principle examples, we show the feasibility of our method. In particular, we identify the induced refractive index change to about a value of Δn=1.5⋅10−3. We also determine our current limitations by calculating the overlap in the form of a scalar product and we discuss possible future improvements. Y1 - 2022 U6 - https://doi.org/10.1007/s00340-022-07928-2 SN - 1432-0649 (Online) SN - 0946-2171 (Print) N1 - Corresponding author: Robert Fleischhaker VL - 128 IS - Article number: 208 SP - 1 EP - 11 PB - Springer CY - Berlin ER - TY - CHAP A1 - Amir, Malik A1 - Bauckhage, Christian A1 - Chircu, Alina A1 - Czarnecki, Christian A1 - Knopf, Christian A1 - Piatkowski, Nico A1 - Sultanow, Eldar T1 - What can we expect from quantum (digital) twins? T2 - Wirtschaftsinformatik 2022 Proceedings N2 - Digital twins enable the modeling and simulation of real-world entities (objects, processes or systems), resulting in improvements in the associated value chains. The emerging field of quantum computing holds tremendous promise forevolving this virtualization towards Quantum (Digital) Twins (QDT) and ultimately Quantum Twins (QT). The quantum (digital) twin concept is not a contradiction in terms - but instead describes a hybrid approach that can be implemented using the technologies available today by combining classicalcomputing and digital twin concepts with quantum processing. This paperpresents the status quo of research and practice on quantum (digital) twins. It alsodiscuses their potential to create competitive advantage through real-timesimulation of highly complex, interconnected entities that helps companies better address changes in their environment and differentiate their products andservices. KW - Artificial Intelligence KW - Digital Twin Evolution KW - Machine Learning KW - Quantum Computing KW - Quantum Machine Learning Y1 - 2022 N1 - 17. Internationale Tagung Wirtschaftsinformatik, 21. – 23. Februar 2022, Nürnberg (online) SP - 1 EP - 14 PB - AIS Electronic Library (AISeL) ER - TY - JOUR A1 - Philipp, Mohr A1 - Efthimiou, Nikos A1 - Pagano, Fiammetta A1 - Kratochwil, Nicolaus A1 - Pizzichemi, Marco A1 - Tsoumpas, Charalampos A1 - Auffray, Etiennette A1 - Ziemons, Karl T1 - Image reconstruction analysis for positron emission tomography with heterostructured scintillators JF - IEEE Transactions on Radiation and Plasma Medical Sciences N2 - The concept of structure engineering has been proposed for exploring the next generation of radiation detectors with improved performance. A TOF-PET geometry with heterostructured scintillators with a pixel size of 3.0×3.1×15 mm3 was simulated using Monte Carlo. The heterostructures consisted of alternating layers of BGO as a dense material with high stopping power and plastic (EJ232) as a fast light emitter. The detector time resolution was calculated as a function of the deposited and shared energy in both materials on an event-by-event basis. While sensitivity was reduced to 32% for 100 μm thick plastic layers and 52% for 50 μm, the CTR distribution improved to 204±49 ps and 220±41 ps respectively, compared to 276 ps that we considered for bulk BGO. The complex distribution of timing resolutions was accounted for in the reconstruction. We divided the events into three groups based on their CTR and modeled them with different Gaussian TOF kernels. On a NEMA IQ phantom, the heterostructures had better contrast recovery in early iterations. On the other hand, BGO achieved a better contrast to noise ratio (CNR) after the 15th iteration due to the higher sensitivity. The developed simulation and reconstruction methods constitute new tools for evaluating different detector designs with complex time responses. KW - TOF PET KW - Heterostructure KW - Metascintillator KW - Multiple TOF kernels KW - Image Reconstruction Y1 - 2022 U6 - https://doi.org/10.1109/TRPMS.2022.3208615 SN - 2469-7311 SN - 2469-7303 VL - 7 IS - 1 SP - 41 EP - 51 PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Bauschat, J.-Michael A1 - Benner, Miriam A1 - Klinge, Henner A1 - Ziegler, Simon T1 - Urbane Mobilität entdeckt die 3. Dimension T2 - Transforming Mobility – What Next? N2 - Der Themenkomplex urbane Mobilität ist getrieben durch den Verkehrsinfarkt in Ballungszentren, durch Luftverschmutzung und Lärm, sowie den Trend zum Leben in der Stadt in den städteplanerischen Fokus gerückt. Emissionsneutrale Antriebskonzepte in der Luftfahrt führen zu Ansätzen Fluggeräte einzusetzen, die batteriegetrieben vertikal aufsteigen und landen können. Flugphysikalisch und energetisch ist diese Technik nur dann sinnvoll, wenn es zwingende Gründe gibt (z.B. Rettungseinsätze), daher wird der flugphysikalische Hintergrund prinzipiell erläutert. Es werden einige aktuelle Lufttransportkonzepte für eine urbane Personenbeförderung vorgestellt. Sollte es verstärkt zu Lufttransport über Städten kommen, müssen betroffene Lufträume geordnet und überwacht werden. Wie kompatibel Lufttransportsysteme mit den heute bereits relevanten urbanen Beförderungsmitteln sein müssen, wird kritisch diskutiert. Abschließend werden die Aspekte Akzeptanz durch die Kunden und Wirtschaftlichkeit ebenso angerissen, wie die hochproblematische Rohstoffgewinnung, die Entsorgung und das Recycling von Batterien. Y1 - 2022 SN - 978-3-658-36429-8 U6 - https://doi.org/10.1007/978-3-658-36430-4_53 N1 - Tagungsband zum 13. Wissenschaftsforum Mobilität, Beiträge des Wissenschaftsforums SP - 895 EP - 916 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Fissabre, Anke ED - Dux, Holger A. T1 - Die Bauten des jüdischen Friedhofs an der Lütticher Straße T2 - Der Jüdische Friedhof Aachen Y1 - 2022 SN - 978-3-87519-266-7 SP - 51 EP - 69 PB - Mayersche Buchhandlung Aachen GmbH CY - Aachen ER - TY - CHAP A1 - Fissabre, Anke ED - Dux, Holger A. T1 - Ein Entwurf für die Umnutzung der Bauten des jüdischen Friedhofs an der Lütticher Straße T2 - Der jüdische Friedhof Aachen Lütticher Straße Aachen Y1 - 2022 SN - 978-3-87519-266-7 SP - 71 EP - 74 PB - Mayersche Buchhandlung Aachen GmbH CY - Aachen ER - TY - JOUR T1 - Dimensionen 1-2022: Magazin der FH Aachen University of Applied Sciences - Auf dem Weg zur Nachhaltigkeit N2 - Inhaltsverzeichnis: 06| "WIR" werden nachhaltig 10| Der Kraft-Stoff aus dem Bioreaktor 14| Energieverbrauch des Campus Jülich optimieren 16| „Eine große Hilfestellung für Flutopfer“ 20| Von der ersten Skizze zu den Blumen in der Vase 22|Wie schläft es sich im All, Herr Maurer? 24| Expedition Arktis 28| Eine Frage, zwei Antworten 30| Der schönste Arbeitsplatz der Welt 32| Im Einklang 36| Ein Vorgeschmack auf die echte Arbeitswelt 38| Den Rätseln des Universums auf der Spur 40| Auf Umwegen in die Spitzenforschung 42| Klappe FH Aachen, die erste … Kamera läuft! 44| Auszeit 46| „Fotografie öffnet Türen zu Parallelwelten“ 50| Es gibt viel zu tun 52| Durch-Blick 54| Weichen stellen für einen ganz besonderen Job 58| Souta, Iver und der Wind 60| Die FH Aachen ist systemakkreditiert 61| Der Vulkan 62| Kopfnuss, Impressum T3 - Dimensionen - Magazin der FH Aachen University of Applied Sciences - 2022, 1 Y1 - 2022 CY - Aachen ER - TY - THES A1 - Keller, Simon Mark T1 - Risikoanalyse einer bordautonomen Schienenfahrzeugortung mittels GNSS N2 - Bei Schienenfahrzeugen, die mit dem Zugsicherungssystem ETCS betrieben sind, wird die Odometrie durch eine diskrete Ortung mittels physischen Balisen zurückgesetzt. Diese Arbeit befasst sich mit der Innovation von virtuellen Balisen. Virtuelle Balisen, können eingesetzt werden, um physische, im Gleisbett montierte Balisen zu ersetzen. Durch den Einsatz von virtuellen Balisen soll der Infrastrukturausbau von ETCS vorangetrieben werden, indem sie als virtuelle Komponente auf Schienenfahrzeugen eingesetzt werden. Im Rahmen dieser Arbeit wird die Fragestellung beantwortet, ob eine bordautonome Zugortung mittels virtuellen Balisen in einem ausgewählten Szenario mit einem akzeptablen Risiko verbunden ist? Das Szenario besteht aus einem Schienenfahrzeug, welches mit dem Zugsicherungssystem ETCS Level 2 auf einer eingleisigen Nebenstrecke betreiben wird. Hierzu werden zunächst die Grundlagen von ETCS und der satellitenbasierten Ortung erläutert. Des Weiteren werden die Grundlagen des CSM Prozesses und der expliziten Risikoabschätzung eingeführt. Aufbauend auf diesen Grundlagen wird der CSM Prozess angewandt und dabei eine Systemdefinition mit den Schnittstellen des Systems zur Umwelt erstellt. Mit der Hazop-Methode werden die Gefährdungen der Schnittstellen erfasst und beurteilt. Die sicherheitsrelevanten Gefährdungen werden in einer FMEA bewertet. In der folgenden Diskussion werden sicherheitsrelevante Gefährdungen nochmals betrachtet. Das Ergebnis der Arbeit ist, dass im ausgewählten Szenario, unter der Verwendung der CSM-Prozesse und der industriell anerkannten Methoden Hazop und FMEA, die Integration der Board-autonomen-Ortung mit einem akzeptablen Risiko verbunden ist. Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Fissabre, Anke ED - Soldwisch, Ines ED - Schmitz, Stefan T1 - kirchen-bauhaus? – Die Kunstgewerbeschule in Aachen unter Rudolf Schwarz T2 - Zwischen den Zeiten - Besatzung und Aufbruch in Aachen, 1919-1932 Y1 - 2022 SN - 978-3-9825016-0-4 N1 - Zeitreisen Sammlung Crous, Schriftenreihe 15. SP - 54 EP - 65 PB - Aachener Karnevalsverein (AKV) CY - Aachen ER - TY - BOOK A1 - Tünnemann, Thomas T1 - Formine 2022 : Concezione I N2 - Der diesjährige Workshop steht im Zeichen der räumlichen Konzeption. Das Definieren und Erfahren des engsten, ganz eigenen Betrachtungsraums, bis hin zur weitläufigen öffentlichen Umgebung des Ortes ist hierbei der erste Schritt. Hierzu stehen alle konzeptionellen Werkzeuge – von der Entwicklung vereinzelter Skizzenabfolgen, bis hin zur Collage - in den ersten Tagen des Workshops zur Verfügung. Abschließend gilt es, den Aufbau - das „Sichzusammenfügen“ aus Form, Relation und Material - in einer Plastik zu vereinen. Y1 - 2022 SN - 3-9811003-9-5 PB - FH Aachen, Fachbereich Architektur CY - Aachen ER - TY - JOUR A1 - Hahn, Geogr W. A1 - Hebel, Christoph A1 - Manz, W. T1 - Die neuen Empfehlungen für Verkehrsnachfragemodellierung im Personenverkehr JF - Straßenverkehrstechnik N2 - Die neu erschienenen „Empfehlungen zum Einsatz von Verkehrsnachfragemodellen für den Personenverkehr“ liefern erstmals als Empfehlungspapier der Forschungsgesellschaft für Straßen- und Verkehrswesen einen umfassenden Überblick zu den verschiedenen Aspekten der Modellierung und geben dem Fachplaner konkrete Hilfestellung für die Konzeption von Nachfragemodellen. Das Empfehlungspapier zielt unter anderem darauf ab, die Erwartungen und das Anspruchsniveau in Hinblick auf Sachgerechtigkeit der Modelle, die erzielbare Modellqualität und den Detaillierungsgrad der Modellaussagen zu harmonisieren. Y1 - 2022 U6 - https://doi.org/10.53184/SVT10-2022-1 SN - 0039-2219 VL - 66 IS - 10 SP - 721 EP - 726 PB - Kirschbaum Verlag GmbH CY - Bonn ER - TY - JOUR A1 - Emig, J. A1 - Hebel, Christoph A1 - Schwark, A. T1 - Einsatzbereiche für Verkehrsnachfragemodelle JF - Straßenverkehrstechnik N2 - In der Praxis bestehen vielfältige Einsatzbereiche für Verkehrsnachfragemodelle. Mit ihnen können Kenngrößen des Verkehrsangebots und der Verkehrsnachfrage für den heutigen Zustand wie auch für zukünftige Zustände bereitgestellt werden, um so die Grundlagen für verkehrsplanerische Entscheidungen zu liefern. Die neuen „Empfehlungen zum Einsatz von Verkehrsnachfragemodellen für den Personenverkehr“ (EVNM-PV) (FGSV 2022) veranschaulichen anhand von typischen Planungsaufgaben, welche differenzierten Anforderungen daraus für die Modellkonzeption und -erstellung resultieren. Vor dem Hintergrund der konkreten Aufgabenstellung sowie deren spezifischer planerischer Anforderungen bildet die abzuleitende Modellspezifikation die verabredete Grundlage zwischen Auftraggeber und Modellersteller für die konkrete inhaltliche, fachliche Ausgestaltung des Verkehrsmodells. Y1 - 2022 U6 - https://doi.org/10.53184/SVT10-2022-2 SN - 0039-2219 VL - 66 IS - 10 SP - 727 EP - 736 PB - Kirschbaum Verlag GmbH CY - Bonn ER - TY - JOUR A1 - Kindmann, Rolf A1 - Kraus, Matthias A1 - Laumann, Jörg A1 - Vette, Jan T1 - Verallgemeinerte Berechnungsmethode für in Beton eingespannte Stahlprofile – Einspanntiefen, Tragfähigkeitsnachweise und Bemessungshilfen JF - Stahlbau N2 - Stützen und Träger aus Stahlprofilen können in Fundamente oder Wände aus Stahlbeton einbetoniert werden. Diese Anschlüsse wirken in der Regel wie Einspannungen, die eine ausreichende Einspanntiefe erfordern. Im Folgenden wird eine verallgemeinerte Berechnungsmethode für in Stahlbetonkonstruktionen eingespannte Stahlprofile aus gewalzten I-Profilen, geschweißten I-Profilen, runden Hohlprofilen, eckigen Hohlprofilen und einzelligen Kastenquerschnitten vorgestellt. Für Beanspruchungen infolge einachsiger Biegung um die starke und schwache Profilachse werden der profilabhängige Ansatz der Betondruckspannungen im Einspannbereich und die Ermittlung der Einspanntiefe behandelt. Unter Berücksichtigung der Normalkraft werden an den maßgebenden Stellen Tragfähigkeitsnachweise für die Stahlprofile geführt. Als Ergänzung zu den Berechnungsformeln werden Bemessungshilfen zur Verfügung gestellt, die die Wahl der mitwirkenden Breiten und der Einspanntiefen erleichtert. KW - Stahlprofile KW - Anschlüsse an Stahlbeton KW - Einspanntiefen KW - Eingespannte Stützen und Träger KW - steel profiles Y1 - 2022 U6 - https://doi.org/10.1002/stab.202200024 SN - 1437-1049 VL - 93 IS - Early View SP - 1 EP - 25 PB - Ernst & Sohn GmbH CY - Berlin ER - TY - BOOK A1 - Laumann, Jörg A1 - Feldmann, Markus A1 - Frickel, Jörg A1 - Krahwinkel, Manuel A1 - Kraus, Matthias A1 - Stranghöner, Natalie A1 - Ummenhofer, Thomas T1 - Petersen Stahlbau : Grundlagen der Berechnung und baulichen Ausbildung von Stahlbauten N2 - Die Theorie und Konstruktion der wichtigsten Bereiche der Stahlbautechnik werden von den Grundlagen her entwickelt und durch viele Beispiele praxisbezogen erläutert. Das Buch ist aus Vorlesungen im Grund- und Vertiefungsstudium des Bauingenieurwesens entstanden. Der Inhalt wird zum Teil systematisch, zum Teil exemplarisch dargestellt. Für Konstrukteure und Statiker in den technischen Büros, der Beratenden Ingenieure und der Prüfämter enthält das Buch aufbereitete Berechnungsverfahren und Konstruktionsvorschläge in großer Zahl. KW - Behälterbau KW - Bemessung KW - Brandschutz KW - Brückenbau KW - Festigkeitslehre Y1 - 2022 SN - 978-3-658-20510-2 U6 - https://doi.org/10.1007/978-3-658-20510-2 PB - Springer Vieweg CY - Wiesbaden ET - 5. Auflage ER - TY - CHAP A1 - Bensberg, Frank A1 - Czarnecki, Christian A1 - Grob, Heinz Lothar ED - Bruhn, Manfred ED - Hadwich, Karsten T1 - Wirtschaftlichkeitsbewertung von Smart Services mit vollständigen Finanzplänen T2 - Smart Services: Band 1: Konzepte – Methoden – Prozesse N2 - Dieser Beitrag stellt einen Bewertungsrahmen für Smart Services vor, der auf dem Konzept vollständiger Finanzpläne (VOFI) basiert. Zunächst wird eine IoT-Architektur für Smart Services eingeführt, die die Grundlage für deren Betrachtung aus Sicht der Unternehmensplanung liefert. Hierauf aufbauend wird ein Bewertungsrahmen für die finanzplanorientierte Wirtschaftlichkeitsbewertung von Smart Services geschaffen, mit dem die relevanten Zahlungsfolgen differenziert erfasst werden. Mithilfe des entwickelten VOFI-Systems wird anschließend aufgezeigt, wie mithilfe einer Risikoanalyse die Unsicherheit von Modellparametern berücksichtigt werden kann. Y1 - 2022 SN - 978-3-658-37344-3 (Online) SN - 978-3-658-37343-6 (Print) U6 - https://doi.org/10.1007/978-3-658-37344-3_6 SP - 225 EP - 251 PB - Springer Gabler CY - Wiesbaden ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - A goodness-of-fit test for the compound Poisson exponential model JF - Journal of Multivariate Analysis N2 - On the basis of bivariate data, assumed to be observations of independent copies of a random vector (S,N), we consider testing the hypothesis that the distribution of (S,N) belongs to the parametric class of distributions that arise with the compound Poisson exponential model. Typically, this model is used in stochastic hydrology, with N as the number of raindays, and S as total rainfall amount during a certain time period, or in actuarial science, with N as the number of losses, and S as total loss expenditure during a certain time period. The compound Poisson exponential model is characterized in the way that a specific transform associated with the distribution of (S,N) satisfies a certain differential equation. Mimicking the function part of this equation by substituting the empirical counterparts of the transform we obtain an expression the weighted integral of the square of which is used as test statistic. We deal with two variants of the latter, one of which being invariant under scale transformations of the S-part by fixed positive constants. Critical values are obtained by using a parametric bootstrap procedure. The asymptotic behavior of the tests is discussed. A simulation study demonstrates the performance of the tests in the finite sample case. The procedure is applied to rainfall data and to an actuarial dataset. A multivariate extension is also discussed. KW - Bootstrapping KW - Collective risk model Y1 - 2022 U6 - https://doi.org/10.1016/j.jmva.2022.105154 SN - 0047-259X SN - 1095-7243 VL - 195 IS - Article 105154 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Evans, Benjamin A1 - Braun, Sebastian A1 - Ulmer, Jessica A1 - Wollert, Jörg T1 - AAS implementations - current problems and solutions T2 - 20th International Conference on Mechatronics - Mechatronika (ME) N2 - The fourth industrial revolution presents a multitude of challenges for industries, one of which being the increased flexibility required of manufacturing lines as a result of increased consumer demand for individualised products. One solution to tackle this challenge is the digital twin, more specifically the standardised model of a digital twin also known as the asset administration shell. The standardisation of an industry wide communications tool is a critical step in enabling inter-company operations. This paper discusses the current state of asset administration shells, the frameworks used to host them and their problems that need to be addressed. To tackle these issues, we propose an event-based server capable of drastically reducing response times between assets and asset administration shells and a multi-agent system used for the orchestration and deployment of the shells in the field. KW - Industry 4.0 KW - Multi-agent Systems KW - Digital Twin KW - Asset Administration Shell Y1 - 2022 SN - 978-1-6654-1040-3 U6 - https://doi.org/10.1109/ME54704.2022.9982933 N1 - 20th International Conference on Mechatronics - Mechatronika (ME), 07-09 December 2022, Pilsen, Czech Republic PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Wiegner, Jonas A1 - Volker, Hanno A1 - Mainz, Fabian A1 - Backes, Andreas A1 - Löken, Michael A1 - Hüning, Felix T1 - Wiegand-effect-powered wireless IoT sensor node T2 - ITG-Fb. 303: Sensoren und Messsysteme N2 - In this article we describe an Internet-of-Things sensing device with a wireless interface which is powered by the oftenoverlooked harvesting method of the Wiegand effect. The sensor can determine position, temperature or other resistively measurable quantities and can transmit the data via an ultra-low power ultra-wideband (UWB) data transmitter. With this approach we can energy-self-sufficiently acquire, process, and wirelessly transmit data in a pulsed operation. A proof-of-concept system was built up to prove the feasibility of the approach. The energy consumption of the system is analyzed and traced back in detail to the individual components, compared to the generated energy and processed to identify further optimization options. Based on the proof-of-concept, an application demonstrator was developed. Finally, we point out possible use cases. Y1 - 2022 SN - 978-3-8007-5835-7 N1 - Sensoren und Messsysteme - 21. ITG/GMA-Fachtagung, 10.05.2022 - 11.05.2022 in Nürnberg SP - 255 EP - 260 PB - VDE Verlag GmbH CY - Berlin ER -