TY  - CHAP
A1  - Koplin, Tobias J.
A1  - Siemons, Maike
A1  - Océn-Valéntin, César
A1  - Sanders, Daniel
A1  - Simon, Ulrich
T1  - Workflow for high throughput screening of gas sensing materials
N2  - The workflow of a high throughput screening setup for the rapid identification of new and improved sensor materials is presented. The polyol method was applied to prepare nanoparticular metal oxides as base materials, which were functionalised by surface doping. Using multi-electrode substrates and high throughput impedance spectroscopy (HT-IS) a wide range of materials could be screened in a short time. Applying HT-IS in search of new selective gas sensing materials a NO2-tolerant NO sensing material with reduced sensitivities towards other test gases was identified based on iridium doped zinc oxide. Analogous behaviour was observed for iridium doped indium oxide.
KW  - Biosensor
KW  - High throughput experimentation
KW  - gas sensor
KW  - metal oxide
KW  - doping
KW  - impedance spectroscopy
KW  - nitrogen oxides
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1407
ER  - 
TY  - CHAP
A1  - Merten, Sabine
A1  - Conrad, Thorsten
A1  - Kämper, Klaus-Peter
A1  - Picard, Antoni
A1  - Schütze, Andreas
T1  - Virtual Technology Labs - an efficient tool for the preparation of hands-on-MEMS-courses in training foundries
N2  - Hands-on-training in high technology areas is usually limited due to the high cost for lab infrastructure and equipment. One specific example is the field of MEMS, where investment and upkeep of clean rooms with microtechnology equipment is either financed by production or R&D projects greatly reducing the availability for education purposes. For efficient hands-on-courses a MEMS training foundry, currently used jointly by six higher education institutions, was established at FH Kaiserslautern. In a typical one week course, students manufacture a micromachined pressure sensor including all lithography, thin film and packaging steps. This compact and yet complete program is only possible because participants learn to use the different complex machines in advance via a Virtual Training Lab (VTL). In this paper we present the concept of the MEMS training foundry and the VTL preparation together with results from a scientific evaluation of the VTL over the last three years.
KW  - Virtuelles Laboratorium
KW  - Virtuelles Labor
KW  - Hand-on-training
KW  - Virtual Technology Lab
KW  - MEMS ; education and training foundry
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Kob, Malte
A1  - Gömmel, Andreas
A1  - Butenweg, Christoph
A1  - Niendorf, Thoralf
T1  - Training of a combined model of larynx and vocal folds with data from MRI measurements
T2  - The 5th International Conference on Voice Physiology and Biomechanics: Variations across Cultures and Species, July 12-14, 2006, Tokyo, Japan. Proceedings
Y1  - 2006
SP  - 45
EP  - 46
ER  - 
TY  - CHAP
A1  - Blaß, Hans Joachim
A1  - Uibel, Thomas
ED  - Kuhlmann, U.
T1  - Tragfähigkeit von stiftförmigen Verbindungsmitteln in Brettsperrholz
T2  - Forschungskolloquium, Holzbau Forschung und Praxis, Stuttgart 2006. Tagungsband
Y1  - 2006
SP  - 167
EP  - 174
PB  - Universität
CY  - Stuttgart
ER  - 
TY  - CHAP
A1  - Herrmann, Ulf
A1  - Worringer, S.
A1  - Graeter, F.
A1  - Nava, P.
ED  - Romero, Manuel
T1  - Three Years of Operation Experience of the SKAL-ET Collector Loop at SEGS V
T2  - 13th International Symposium Concentrated Solar Power and Chemical Energy Technologies, June 20 - 23, 2006, Seville, Spain
Y1  - 2006
SN  - 84-7834-519-1
PB  - SolarPACES [u.a.]
CY  - [s.l.]
ER  - 
TY  - CHAP
A1  - Kloock, Joachim P.
A1  - Schubert, J.
A1  - Ermelenko, Y.
A1  - Vlasov, Y. G.
A1  - Bratov, A.
A1  - Schöning, Michael Josef
T1  - Thin-film sensors with chalcogenide glass materials – a general survey
T2  - Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...
Y1  - 2006
SP  - 92
EP  - 97
CY  - Warsaw
ER  - 
TY  - CHAP
A1  - Ballmann, Josef
A1  - Dafnis, Athanasios
A1  - Braun, Carsten
A1  - Korsch, Helge
A1  - Reimerdes, Hans-Günther
A1  - Braun, Carsten
A1  - Ballmann, Josef
T1  - The HIRENASD project: High Reynolds number aerostructural dynamics experiments in the European Transonic Wind Tunnel (ETW)
T2  - ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences
Y1  - 2006
SN  - 0-9533991-7-6
SP  - Paper No. 2006-5.11.2
PB  - Optimage
CY  - Edinburgh
ER  - 
TY  - CHAP
A1  - Vedral, Andreas
A1  - Wollert, Jörg
A1  - Buda, A.
A1  - Altrock, R.
T1  - The capability of bluetooth for real-time transmission in automation
T2  - Proceedings of the IASTED International Conference on Networks and Communication Systems 2006 : March 29 - 31, 2006, Chiang Mai, Thailand
Y1  - 2006
SP  - 168
EP  - 175
PB  - Acta Pr.
CY  - Anaheim, Calif.
ER  - 
TY  - CHAP
A1  - Gebhardt, Andreas
T1  - Technology Diffusion through a Multi-Level Technology Transfer Infrastructure. Contribution to the 1st. All Africa Technology Diffusion Conference Boksburg, South Africa June 12th - 14th 2006
N2  - Table of contents 1. Introduction 2. Multi-level Technology Transfer Infrastructure 2.1 Level 1: University Education – Encourage the Idea of becoming an Entrepreneur 2.2 Level 2: Post Graduate Education – Improve your skills and focus it on a product family. 2.3 Level 3: Birth of a Company – Focus your skills on a product and a market segment. 2.4 Level 4: Ready to stand alone – Set up your own business 2.5 Level 5: Grow to be Strong – Develop your business 2.6 Level 6: Competitive and independent – Stay innovative. 3. Samples 3.1 Sample 1: Laser Processing and Consulting Centre, LBBZ 3.2 Sample 2: Prototyping Centre, CP 4. Funding - Waste money or even lost Money? 5. Conclusion
KW  - Technologietransfer
KW  - technology transfer
KW  - technology diffusion
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Pijanowska, Dorota G.
A1  - Remiszewska, Elzbieta
A1  - Pederzolli, Cecilia
A1  - Lunelli, Lorenzo
A1  - Vendano, Michele
A1  - Canteri, Roberto
A1  - Dudzinski, Konrad
A1  - Kruk, Jerzy
A1  - Torbicz, Wladyslaw
T1  - Surface modification for microreactor fabrication
N2  - In this paper, methods of surface modification of different supports, i.e. glass and polymeric beads for enzyme immobilisation are described. The developed method of enzyme immobilisation is based on Schiff’s base formation between the amino groups on the enzyme surface and the aldehyde groups on the chemically modified surface of the supports. The surface of silicon modified by APTS and GOPS with immobilised enzyme was characterised by atomic force microscopy (AFM), time-of-flight secondary ion mass spectroscopy (ToF-SIMS) and infrared spectroscopy (FTIR). The supports with immobilised enzyme (urease) were also tested in combination with microreactors fabricated in silicon and Perspex, operating in a flow-through system. For microreactors filled with urease immobilised on glass beads (Sigma) and on polymeric beads (PAN), a very high and stable signal (pH change) was obtained. The developed method of urease immobilisation can be stated to be very effective.
KW  - Biosensor
KW  - Microreactors
KW  - surface modification
KW  - enzyme immobilisation
KW  - lab-on-a-chip
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1480
ER  - 
TY  - CHAP
A1  - Srivastava, Alok
A1  - Singh, Virendra
A1  - Dhand, Chetna
A1  - Kaur, Manindar
A1  - Singh, Tejvir
A1  - Witte, Katrin
A1  - Scherer, Ulrich W.
T1  - Study of swift heavy ion modified conduction polymer composites for application as gas sensor
N2  - A polyaniline-based conducting composite was prepared by oxidative polymerisation of aniline in a polyvinylchloride (PVC) matrix. The coherent free standing thin films of the composite were prepared by a solution casting method. The polyvinyl chloride-polyaniline composites exposed to 120 MeV ions of silicon with total ion fluence ranging from 1011 to 1013 ions/cm2, were observed to be more sensitive towards ammonia gas than the unirradiated composite. The response time of the irradiated composites was observed to be comparably shorter. We report for the first time the application of swift heavy ion modified insulating polymer conducting polymer (IPCP) composites for sensing of ammonia gas.
KW  - Biosensor
KW  - Conducing polymer
KW  - ammonia gas sensors
KW  - swift heavy ions
KW  - polymer composites
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1345
ER  - 
TY  - CHAP
A1  - Schwarzer, Klemens
T1  - Solarthermisches Entsalzungssystem mit Wärmerückgewinnung - Erste Feldtestergebnisse
T2  - 16. Symposium Thermische Solarenergie : 17. bis 19. Mai 2006, Kloster Banz, Bad Staffelstein
Y1  - 2006
SN  - 3-934681-45-X
SP  - 173
EP  - 178
PB  - Ostbayer. Technologie-Transfer-Inst.
CY  - Regensburg
ER  - 
TY  - CHAP
A1  - Dachwald, Bernd
A1  - Kahle, Ralph
A1  - Wie, Bong
T1  - Solar sail Kinetic Energy Impactor (KEI) mission design tradeoffs for impacting and deflecting asteroid 99942 Apophis
T2  - AIAA/AAS Astrodynamics Specialist Conference and Exhibit
N2  - Near-Earth asteroid 99942 Apophis provides a typical example for the evolution of asteroid orbits that lead to Earth-impacts after a close Earth-encounter that results in a resonant return. Apophis will have a close Earth-encounter in 2029 with potential very close subsequent Earth-encounters (or even an impact) in 2036 or later, depending on whether it passes through one of several so-called gravitational keyholes during its 2029-encounter. Several pre-2029-deflection scenarios to prevent Apophis from doing this have been investigated so far. Because the keyholes are less than 1 km in size, a pre-2029 kinetic impact is clearly the best option because it requires only a small change in Apophis' orbit to nudge it out of a keyhole. A single solar sail Kinetic Energy Impactor (KEI) spacecraft that impacts Apophis from a retrograde trajectory with a very high relative velocity (75-80 km/s) during one of its perihelion passages at about 0.75 AU would be a feasible option to do this. The spacecraft consists of a 160 m x 160 m, 168 kg solar sail assembly and a 150 kg impactor. Although conventional spacecraft can also achieve the required minimum deflection of 1 km for this approx. 320 m-sized object from a prograde trajectory, our solar sail KEI concept also allows the deflection of larger objects. In this paper, we also show that, even after Apophis has flown through one of the gravitational keyholes in 2029, solar sail Kinetic Energy Impactor (KEI) spacecraft are still a feasible option to prevent Apophis from impacting the Earth, but many KEIs would be required for consecutive impacts to increase the total Earth-miss distance to a safe value. In this paper, we elaborate potential pre- and post-2029 KEI impact scenarios for a launch in 2020, and investigate tradeoffs between different mission parameters.
KW  - Solar Sail
KW  - Asteroid Deflection
KW  - Planetary Protection
KW  - Trajectory Optimization
Y1  - 2006
U6  - http://dx.doi.org/10.2514/6.2006-6178
N1  - AIAA/AAS Astrodynamics Specialist Conference and Exhibit, 21 August 2006 - 24 August 2006, Keystone, Colorado(USA).
SP  - 1
EP  - 20
ER  - 
TY  - CHAP
A1  - Barek, Jiri
A1  - Fischer, Jan
A1  - Navratil, Tomas
A1  - Peckova, Karolina
A1  - Yosypchuk, Bogdan
T1  - Silver solid amalgam electrodes as sensors for chemical carcinogens
N2  - The applicability of differential pulse voltammetry (DPV) and adsorptive stripping voltammetry (AdSV) at a non-toxic meniscus-modified silver solid amalgam electrode (m-AgSAE) for the determination of trace amounts of genotoxic substances was demonstrated on the determination of micromolar and submicromolar concentrations of 3-nitrofluoranthene using methanol - 0.01 mol L-1 NaOH (9:1) mixture as a base electrolyte and of Ostazine Orange using 0.01 mol L-1 NaOH as a base electrolyte.
KW  - Biosensor
KW  - Solid amalgam electrodes
KW  - voltammetry
KW  - carcinogens
KW  - 3-nitrofluoranthene
KW  - Ostazine Orange
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1554
ER  - 
TY  - CHAP
A1  - Loeb, Horst W.
A1  - Schartner, Karl-Heinz
A1  - Seboldt, Wolfgang
A1  - Dachwald, Bernd
A1  - Streppel, Joern
A1  - Meusemann, Hans
A1  - Schülke, Peter
T1  - SEP for a lander mission to the jovian moon europa
T2  - 57th International Astronautical Congress
N2  - Under DLR-contract, Giessen University and DLR Cologne are studying solar-electric propulsion missions (SEP) to the outer regions of the solar system. The most challenging reference mission concerns the transport of a 1.35-tons chemical lander spacecraft into an 80-RJ circular orbit around Jupiter, which would enable to place a 375 kg lander with 50 kg of scientific instruments on the surface of the icy moon "Europa". Thorough analyses show that the best solution in terms of SEP launch mass times thrusting time would be a two-stage EP module and a triple-junction solar array with concentrators which would be deployed step by step. Mission performance optimizations suggest to propel the spacecraft in the first EP stage by 6 gridded ion thrusters, running at 4.0 kV of beam voltage, which would save launch mass, and in the second stage by 4 thrusters with 1.25 to 1.5 kV of positive high voltage saving thrusting time. In this way, the launch mass of the spacecraft would be kept within 5.3 tons. Without a launcher's C3 and interplanetary gravity assists, Jupiter might be reached within about 4 yrs. The spiraling-down into the parking orbit would need another 1.8 yrs. This "large mission" can be scaled down to a smaller one, e.g., by halving all masses, the solar array power, and the number of thrusters. Due to their reliability, long lifetime and easy control, RIT-22 engines have been chosen for mission analysis. Based on precise tests, the thruster performance has been modeled.
Y1  - 2006
U6  - http://dx.doi.org/10.2514/6.IAC-06-C4.4.04
N1  - 57th International Astronautical Congress, 02 October 2006 - 06 October 2006, Valencia, Spain.
SP  - 1
EP  - 12
ER  - 
TY  - CHAP
A1  - Butenweg, Christoph
A1  - Mistler, Michael
T1  - Seismic resistance of unreinforced masonry buildings
T2  - Proceedings of the Eighth International Conference on Computational Structures Technology : [Las Palmas de Cran Canaria, 12-15 September 2006] / ed. by B. H. V. Topping ...
Y1  - 2006
SN  - 1-905088-06-X
U6  - http://dx.doi.org/10.4203/ccp.83.9
SP  - Paper 9
PB  - Civil-Comp Press
CY  - Stirling
ER  - 
TY  - CHAP
A1  - Türk, Roman
T1  - Sanierung von Hausanschlüssen
N2  - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 23-24. Zusammenfassung des Vortrags.
KW  - Hausanschluss
KW  - Abwasser
KW  - Kanalnetz
KW  - Kanalbetrieb
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Kraft, Bodo
A1  - Retkowitz, Daniel
T1  - Rule-Dependencies for Visual Knowledge Specification in Conceptual Design
N2  - In: Proc. of the 11th Intl. Conf. on Computing in Civil and Building Engineering (ICCCBE-XI) ed. Hugues Rivard, Montreal, Canada, Seite 1-12, ACSE (CD-ROM), 2006 Currently, the conceptual design phase is not adequately supported by any CAD tool. Neither the support while elaborating conceptual sketches, nor the automatic proof of correctness with respect to effective restrictions is currently provided by any commercial tool. To enable domain experts to store the common as well as their personal domain knowledge, we develop a visual language for knowledge formalization. In this paper, a major extension to the already existing concepts is introduced. The possibility to define rule dependencies extends the expressiveness of the knowledge definition language and contributes to the usability of our approach.
KW  - CAD
KW  - CAD
KW  - Bauingenieurwesen
KW  - CAD
KW  - civil engineering
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Sakthivel, Mariappan
A1  - Weppner, Werner
T1  - Response behaviour of a hydrogen sensor based on ionic conducting polymer-metal interfaces prepared by the chemical reduction method
N2  - A solid-state amperometric hydrogen sensor based on a protonated Nafion membrane and catalytic active electrode operating at room temperature was fabricated and tested. Ionic conducting polymer-metal electrode interfaces were prepared chemically by using the impregnation-reduction method. The polymer membrane was impregnated with tetra-ammine platinum chloride hydrate and the metal ions were subsequently reduced by using either sodium tetrahydroborate or potassium tetrahydroborate. The hydrogen sensing characteristics with air as reference gas is reported. The sensors were capable of detecting hydrogen concentrations from 10 ppm to 10% in nitrogen. The response time was in the range of 10-30 s and a stable linear current output was observed. The thin Pt films were characterized by XRD, Infrared Spectroscopy, Optical Microscopy, Atomic Force Microscopy, Scanning Electron Microscopy and EDAX.
KW  - Biosensor
KW  - Hydrogen sensor
KW  - amperometric sensor
KW  - porous Pt electrode
KW  - chemical reduction method
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1399
ER  - 
TY  - CHAP
A1  - Pauksztat, Anja
A1  - Kuperjans, Isabel
A1  - de Hesselle, M.
T1  - Referenzformeln für Energiebedarf und CO2-Emissionen in der Glasindustrie
T2  - Energieeffizienz - Chancen für die Zukunft : Tagung Berlin, 14. und 15. November 2006. - (VDI-Berichte ; 1951)
Y1  - 2006
SN  - 3-18-091951-5
SP  - 179
EP  - 190
PB  - VDI-Verl.
CY  - Düsseldorf
ET  - Nichtred. Ms.-Dr.
ER  - 
TY  - CHAP
A1  - Kurz, Melanie
T1  - Recognition of shape in virtual visualizations
T2  - Proceedings : November 15 - 17, 2006, Technische Universität Darmstadt, Darmstadt, Germany ; PACE, Partners for the advancement of collaborative engineering education
Y1  - 2006
SN  - 978-3-00-020161-5
N1  - International PACE Forum Collaborative Visualization ; (2006, Darmstadt)
SP  - 203
EP  - 209
PB  - Techn. Univ.
CY  - Darmstadt
ER  - 
TY  - CHAP
A1  - Mirmohseni, Abdolreza
A1  - Rostamizadeh, Kobra
T1  - Quartz crystal nanobalance in conjunction with principal component analysis for  identification of volatile organic compounds
N2  - Quartz crystal nanobalance (QCN) sensors are considered as powerful masssensitive sensors to determine materials in the sub-nanogram level. In this study, a single piezoelectric quartz crystal nanobalance modified with polystyrene was employed to detect benzene, toluene, ethylbenzene and xylene (BTEX compounds). The frequency shift of the QCN sensor was found to be linear against the BTEX compound concentrations in the range about 1-45 mg l-1. The correlation coefficients for benzene, toluene, ethylbenzene, and xylene were 0.991, 0.9977, 0.9946 and 0.9971, respectively. The principal component analysis was also utilized to process the frequency response data of the single piezoelectric crystal at different times, considering to the different adsorption-desorption dynamics of BTEX compounds. Using principal component analysis, it was found that over 90% of the data variance could still be explained by use of two principal components (PC1 and PC2). Subsequently, the successful identification of benzene and toluene was possible through the principal component analysis of the transient responses of the polystyrene modified QCN sensor. The results showed that the polystyrene-modified QCN had favorable identification and quantification performances for the BTEX compounds.
KW  - Biosensor
KW  - Quartz crystal nanobalance (QCN)
KW  - BTEX compounds
KW  - principal component
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1434
ER  - 
TY  - CHAP
A1  - Platen, J.
A1  - Poghossian, Arshak
A1  - Schöning, Michael Josef
T1  - Präparation von selbstjustierenden Nanostrukturen mittels Schichtausdehnungstechnik
T2  - Sensoren und Mess-Systeme 2006 : Vorträge der 13. ITG/GMA-Fachtagung vom 13. bis 14.3.2006 in Freiburg/Breisgau
Y1  - 2006
SN  - 3-8007-2939-3
SP  - 277
EP  - 280
PB  - VDE Verl.
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Hellmanns, Mark
A1  - Böhm, Stefan
A1  - Dilger, Klaus
T1  - Progress of the manual application of adhesives
T2  - Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China
Y1  - 2006
SP  - 275
EP  - 277
PB  - Beijing Adhesion Society of China
CY  - Beijing
ER  - 
TY  - CHAP
A1  - Staat, Manfred
T1  - Problems and chances for probabilistic fracture mechanics in the analysis of steel pressure boundary reliability. - Überarb. Ausg.
N2  - In: Technical feasibility and reliability of passive safety systems for nuclear power plants. Proceedings of an Advisory Group Meeting held in Jülich, 21-24 November 1994. - Vienna , 1996. - Seite: 43 - 55 IAEA-TECDOC-920 Abstract: It is shown that the difficulty for probabilistic fracture mechanics (PFM) is the general problem of the high reliability of a small population. There is no way around the problem as yet. Therefore what PFM can contribute to the reliability of steel pressure boundaries is demon­strated with the example of a typical reactor pressure vessel and critically discussed. Although no method is distinguishable that could give exact failure probabilities, PFM has several addi­tional chances. Upper limits for failure probability may be obtained together with trends for design and operating conditions. Further, PFM can identify the most sensitive parameters, improved control of which would increase reliability. Thus PFM should play a vital role in the analysis of steel pressure boundaries despite all shortcomings.
KW  - Bruchmechanik
KW  - probabilistic fracture mechanics
KW  - PFM
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Wagner, Torsten
A1  - Schöning, Michael Josef
T1  - Preface of the Special Issue of I3S 2005 in Jülich (Germany)
N2  - International Symposium on Sensor Science, I3S 2005 <3; 2005; Juelich, Germany> In: Sensors 2006, 6, 260-261 ISSN 1424-8220
KW  - Biosensor
KW  - I3S 2005
KW  - International Symposium on Sensor Science
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1365
ER  - 
TY  - CHAP
A1  - Vredal, Andreas
A1  - Wollert, Jörg
T1  - Praktische Untersuchungen zur Reduzierung der Restfehlerrate von Funksystemen
T2  - Wireless Automation : Chancen, Lösungen, Risiken ; Tagung Darmstadt, 8. und 9. Mai 2006. (VDI-Berichte ; 1939)
Y1  - 2006
SN  - 3-18-091939-6
SP  - 135
EP  - 146
PB  - VDI-Verl.
CY  - Düsseldorf
ER  - 
TY  - CHAP
A1  - Vedral, Andreas
A1  - Wollert, Jörg
T1  - Praktische Untersuchungen zum zeitlichen Übertragungs- und Bündelfehlerverhalten der IEEE 802.15.4
T2  - ZigBee & Co. - drahtlose Nahbereichsnetzwerke : 04. April 2006, München
Y1  - 2006
PB  - Design&Elektronik
CY  - Poing
ER  - 
TY  - CHAP
A1  - Augenstein, Eckardt
A1  - Herbergs, S.
A1  - Kuperjans, Isabel
T1  - Planung und Bewertung der Gebäudeenergieversorgung mit TOP-Energy
T2  - Heizungs- und Raumlufttechnik : 1. Fachtagung Leonberg, 31. Januar bis 1. Februar 2006. - (VDI-Berichte ; Nr. 1921)
Y1  - 2006
SN  - 3-18-091921-3
N1  - Posterbeitrag
SP  - 57
EP  - 60
PB  - VDI-Verl.
CY  - Düsseldorf
ER  - 
TY  - CHAP
A1  - Kretschmann, Lars
T1  - Planung und Bauleitung Buschtunnel Aachen
N2  - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 16-17 Der Umbau des Aachener Buschtunnels im Rahmen des europäischen Hochgeschwindigkeitsschienennetzes wird im sogenannten "Neuen Österreichischen Tunnelbauverfahren (NOeT)", also ein Ausbau in Kalotte, Strosse und Sohle durchgeführt.
KW  - Bauplanung
KW  - Bauführung
KW  - Bauleitung
KW  - Tunnelbau
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Gobbelé, Dirk
T1  - Planung der Umbaumaßnahme Hauptbahnhof Aachen
N2  - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 13-15. Bericht über die infrastrukturellen Maßnahmen zum Umbau des Hauptbahnhofs Aachen.
KW  - Bauplanung
KW  - Umbauplanung
KW  - Verkehrsbau
KW  - Hauptbahnhof Aachen
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Himmerich, Jörg
T1  - Pipeline Integrity Management System - Probabilistische Bewertung von Bauwerken am Beispiel von Hochdruckleitungen
N2  - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 21-22. Zusammenfassung des Vortrags.
KW  - Hochdruckleitung
KW  - PIMS
KW  - Pipeline Integrity Management System
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Pijanowska, Dorota G.
A1  - Remiszewska, Elzbieta
T1  - pH-based detection of phenylalnine by potentiometric and colorimetric methods
N2  - In this paper, methods of sample preparation for potentiometric measurement of phenylalanine are presented. Basing on the spectrophotometric measurements of phenylalanine, the concentrations of reagents of the enzymatic reaction (10 mM L-Phe, 0,4 mM NAD+, 2U L-PheDH) were determined. Then, the absorption spectrum of the reaction product, NADH, was monitored (maximum peak at 340 nm). The results obtained by the spectrophotometric method were compared with the results obtained by the colourimetry, using pH indicators. The above-mentioned two methods will be used as references for potentiometric measurements of phenylalanine concentration.
KW  - Biosensor
KW  - Phenylalanine determination
KW  - enzymatic methods
KW  - pH-based biosensing
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1536
ER  - 
TY  - CHAP
A1  - Wellmann, Judith
T1  - Perspektiven eines Bauingenieurs im konstruktiven Ingenieurbau
N2  - In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 7-12 Die Berufsperspektiven im konstruktiven Ingenieurbau werden trotz sinkendem Bedarf an Statikern positiv bewertet.
KW  - Ingenieurbau
KW  - Konstruktiver Ingenieurbau
KW  - Statiker
KW  - Berufsperspektiven
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Schuh, G.
A1  - Gottschalk, S.
A1  - Höhne, Tim
A1  - Cloots, M.
ED  - Wenzel, Sigrid
T1  - Parametrierung einer Schlupfregelung in der simulativen Produktionsplanung
T2  - Simulation in Produktion und Logistik 2006 : Tagungsband zur 12. Fachtagung, Kassel, 26. - 27. September 2006
Y1  - 2006
SN  - 3-936150-48-6
N1  - ASIM-Mitteilung ; 104
SP  - 233
EP  - 243
ER  - 
TY  - CHAP
A1  - Deterding, A.
A1  - Tippkötter, Nils
A1  - Ulber, R.
ED  - Beckmann, Dieter
T1  - Online-Essigsäureanalytik in Fermentationsbrühen mittels Fließdiffusionstechnik (FDT)
T2  - Technische Systeme für Biotechnologie und Umwelt : 13. Heiligenstädter Kolloquium, Heilbad Heiligenstadt, 25.09. - 27.09.2006
Y1  - 2006
SN  - 978-3-00-018621-9
SP  - 273
EP  - 280
CY  - Heiligenstadt
ER  - 
TY  - CHAP
A1  - Kowalski, Julia
T1  - Numerical Debris Flow Simulation
T2  - Schweizer Numerik Kolloquium : Book of Abstracts 12. April 2006
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Arida, Hassan A.
A1  - Kloock, Joachim P.
A1  - Schöning, Michael Josef
T1  - Novel organic membrane-based thin-film microsensors for the determination of heavy metal cations
N2  - A first step towards the fabrication and electrochemical evaluation of thin-film microsensors based on organic PVC membranes for the determination of Hg(II), Cd(II), Pb(II) and Cu(II) ions in solutions has been realised. The membrane-coating mixture used in the preparation of this new type of microsensors is incorporating PVC as supporting matrix, o-nitrophenyloctylether (o-NPOE) as solvent mediator and a recently synthesized Hg[dimethylglyoxime(phene)]2+ and Bis-(4-hydroxyacetophenone)-ethylenediamine as electroactive materials for Hg(II) and Cd(II), respectively. A set of three commercialised ionophores for Cd(II), Pb(II) and Cu(II) has been also used for comparison. Thin-film microsensors based on these membranes showed a Nernstian response of slope (26-30 mV/dec.) for the respective tested cations. The potentiometric response characteristics (linear range, pH range, detection limit and response time) are comparable with those obtained by conventional membranes as well as coated wire electrodes prepared from the same membrane. The realisation of the new organic membrane-based thin-film microsensors overcomes the problem of an insufficient selectivity of solid-state-based thinfilm sensors.
KW  - Biosensor
KW  - Heavy metal detection
KW  - thin-film microsensors
KW  - organic PVC membranes
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1545
ER  - 
TY  - CHAP
A1  - Hellmanns, Mark
A1  - Böhm, Stefan
A1  - Dilger, Klaus
A1  - Welters, T.
T1  - Neue Möglichkeiten der Klebstoffverarbeitung durch geschwindigkeitsproportionalen Handauftrag
T2  - Adhesive bonding and hybrid bonding in body-in-white shop and assembly : proceedings, 25/26 April 2006, Bad Nauheim/Frankfurt
Y1  - 2006
SP  - 81
PB  - Technik & Kommunikation Verl.-GmbH
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Pfaff, Raphael
A1  - Vinsonneau, B.
A1  - Burnham, K. J.
T1  - Multiple models for nonlinear systems
T2  - Proceedings / Eigteenth International Conference on Systems Engineering : ICSE 2006 : 5 - 7 September 2006 ; [held at Coventry University, UK]
Y1  - 2006
SN  - 1-84600-013-0
SP  - 347
EP  - 352
ER  - 
TY  - CHAP
A1  - Näther, Niko
A1  - Poghossian, Arshak
A1  - Platen, J.
A1  - Yoshinobu, T.
A1  - Koudelka-Hep, M.
A1  - Schöning, Michael Josef
T1  - Multi-parameter sensing of both physical and (bio-)chemical quantities using the same transducer principle
T2  - Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...
Y1  - 2006
SP  - 172
EP  - 181
CY  - Warsaw
ER  - 
TY  - CHAP
A1  - Bukhari, Syed Faisal Ahmed
A1  - Yang, Wuqiang
T1  - Multi-interface level sensors and new development in monitoring and control of oil separators
N2  - In the oil industry, huge saving may be made if suitable multi-interface level measurement systems are employed for effectively monitoring crude oil separators and efficient control of their operation. A number of techniques, e.g. externally mounted displacers, differential pressure transmitters and capacitance rod devices, have been developed to measure the separation process with gas, oil, water and other components. Because of the unavailability of suitable multi-interface level measurement systems, oil separators are currently operated by the trial-and-error approach. In this paper some conventional techniques, which have been used for level measurement in industry, and new development are discussed.
KW  - Biosensor
KW  - Level sensor
KW  - multi-interface measurement
KW  - electrical capacitance tomography
KW  - ECT
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1498
ER  - 
TY  - CHAP
A1  - Chaiyboun, Ali
A1  - Traute, Rüdiger
A1  - Kiesewetter, Olaf
A1  - Ahlers, Simon
A1  - Müller, Gerhard
A1  - Doll, Theodor
T1  - Modular analytical multicomponent analysis in gas sensor arrays
N2  - A multi-sensor system is a chemical sensor system which quantitatively and qualitatively records gases with a combination of cross-sensitive gas sensor arrays and pattern recognition software. This paper addresses the issue of data analysis for identification of gases in a gas sensor array. We introduce a software tool for gas sensor array configuration and simulation. It concerns thereby about a modular software package for the acquisition of data of different sensors. A signal evaluation algorithm referred to as matrix method was used specifically for the software tool. This matrix method computes the gas concentrations from the signals of a sensor array. The software tool was used for the simulation of an array of five sensors to determine gas concentration of CH4, NH3, H2, CO and C2H5OH. The results of the present simulated sensor array indicate that the software tool is capable of the following: (a) identify a gas independently of its concentration; (b) estimate the concentration of the gas, even if the system was not previously exposed to this concentration; (c) tell when a gas concentration exceeds a certain value. A gas sensor data base was build for the configuration of the software. With the data base one can create, generate and manage scenarios and source files for the simulation. With the gas sensor data base and the simulation software an on-line Web-based version was developed, with which the user can configure and simulate sensor arrays on-line.
KW  - Biosensor
KW  - Main sensitivity
KW  - cross sensitivity
KW  - matrix method
KW  - gas sensor array
KW  - modelling
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1358
ER  - 
TY  - CHAP
A1  - Tymecki, Lukasz
A1  - Glab, Stanislaw
A1  - Koncki, Robert
T1  - Miniaturized, planar ion-selective electrodes fabricated by means of thick-film  technology
N2  - Various planar technologies are employed for developing solid-state sensors having low cost, small size and high reproducibility; thin- and thick-film technologies are most suitable for such productions. Screen-printing is especially suitable due to its simplicity, low-cost, high reproducibility and efficiency in large-scale production. This technology enables the deposition of a thick layer and allows precise pattern control. Moreover, this is a highly economic technology, saving large amounts of the used inks. In the course of repetitions of the film-deposition procedure there is no waste of material due to additivity of this thick-film technology. Finally, the thick films can be easily and quickly deposited on inexpensive substrates. In this contribution, thick-film ion-selective electrodes based on ionophores as well as crystalline ion-selective materials dedicated for potentiometric measurements are demonstrated. Analytical parameters of these sensors are comparable with those reported for conventional potentiometric electrodes. All mentioned thick-film strip electrodes have been totally fabricated in only one, fully automated thickfilm technology, without any additional manual, chemical or electrochemical steps. In all cases simple, inexpensive, commercially available materials, i.e. flexible, plastic substrates and easily cured polymer-based pastes were used.
KW  - Biosensor
KW  - Potentiometry
KW  - thick-film technology
KW  - screen-printing
KW  - ion-selective electrodes
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1506
ER  - 
TY  - CHAP
A1  - Platen, Johannes
A1  - Poghossian, Arshak
A1  - Schöning, Michael Josef
T1  - Microstructured Nanostructures – nanostructuring by means of conventional photolithography and layer-expansion technique
N2  - A new and simple method for nanostructuring using conventional photolithography and layer expansion or pattern-size reduction technique is presented, which can further be applied for the fabrication of different nanostructures and nano-devices. The method is based on the conversion of a photolithographically patterned metal layer to a metal-oxide mask with improved pattern-size resolution using thermal oxidation. With this technique, the pattern size can be scaled down to several nanometer dimensions. The proposed method is experimentally demonstrated by preparing nanostructures with different configurations and layouts, like circles, rectangles, trapezoids, “fluidic-channel”-, “cantilever”- and meander-type structures.
KW  - Biosensor
KW  - Nanostructuring
KW  - layer expansion
KW  - pattern-size reduction
KW  - self-aligned patterning
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1477
ER  - 
TY  - CHAP
A1  - Meskouris, Konstantin
A1  - Mistler, Michael
A1  - Butenweg, Christoph
T1  - Mauerwerksbauten unter Erdbebenbelastung
T2  - Numerische Methoden zur Problemlösung im konstruktiven Bauwesen : 34. Aachener Baustofftag ; 02. Februar 2006
Y1  - 2006
PB  - IBAC
CY  - Aachen
ER  - 
TY  - CHAP
A1  - Baronas, Romas
A1  - Ivanauskas, Feliksas
A1  - Kulys, Juozas
T1  - Mathematical modeling of biosensors based on an array of enzyme microreactors
N2  - This paper presents a two-dimensional-in-space mathematical model of biosensors based on an array of enzyme microreactors immobilised on a single electrode. The modeling system acts under amperometric conditions. The microreactors were modeled by particles and by strips. The model is based on the diffusion equations containing a nonlinear term related to the Michaelis-Menten kinetics of the enzymatic reaction. The model involves three regions: an array of enzyme microreactors where enzyme reaction as well as mass transport by diffusion takes place, a diffusion limiting region where only the diffusion takes place, and a convective region, where the analyte concentration is maintained constant. Using computer simulation, the influence of the geometry of the microreactors and of the diffusion region on the biosensor response was investigated. The digital simulation was carried out using the finite difference technique.
KW  - Biosensor
KW  - Reaction-diffusion
KW  - modeling biosensor
KW  - microreactor
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1569
ER  - 
TY  - CHAP
A1  - Schöning, Michael Josef
A1  - Abouzar, Maryam H.
A1  - Han, Y.
A1  - Ingebrandt, S.
A1  - Offenhäusser, A.
A1  - Poghossian, Arshak
T1  - Markierungsfreie DNA-Detektion mit Silizium-Feldeffektsensoren – Messeffekte oder Artefakte?
T2  - Sensoren und Mess-Systeme 2006 : Vorträge der 13. ITG/GMA-Fachtagung vom 13. bis 14.3.2006 in Freiburg/Breisgau
Y1  - 2006
SN  - 3-8007-2939-3
SP  - 443
EP  - 446
PB  - VDE Verl.
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Katz, Eugenii
A1  - Willner, Itamar
T1  - Magneto-controlled quantized electron transfer to surface-confined redox units and metal nanoparticles
N2  - Hydrophobic magnetic nanoparticles (NPs) consisting of undecanoate-capped magnetite (Fe3O4, average diameter ca. 5 nm) are used to control quantized electron transfer to surface-confined redox units and metal NPs. A two-phase system consisting of an aqueous electrolyte solution and a toluene phase that includes the suspended undecanoatecapped magnetic NPs is used to control the interfacial properties of the electrode surface. The attracted magnetic NPs form a hydrophobic layer on the electrode surface resulting in the change of the mechanisms of the surface-confined electrochemical processes. A quinone-monolayer modified Au electrode demonstrates an aqueous-type of the electrochemical process (2e-+2H+ redox mechanism) for the quinone units in the absence of the hydrophobic magnetic NPs, while the attraction of the magnetic NPs to the surface results in the stepwise single-electron transfer mechanism characteristic of a dry nonaqueous medium. Also, the attraction of the hydrophobic magnetic NPs to the Au electrode surface modified with Au NPs (ca. 1.4 nm) yields a microenvironment with a low dielectric constant that results in the single-electron quantum charging of the Au NPs.
KW  - Biosensor
KW  - Nanoparticles
KW  - magnetic particles
KW  - quantum charging
KW  - modified electrode
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1528
ER  - 
TY  - CHAP
A1  - Böhm, Stefan
A1  - Hellmanns, Mark
A1  - Backes, Andreas
A1  - Dilger, Klaus
T1  - Lock-in thermography based NDT of automotive parts
T2  - Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China
Y1  - 2006
SP  - 382
EP  - 384
PB  - Beijing Adhesion Society of China
CY  - Beijing
ER  -