TY - CHAP A1 - Alt, Helmut T1 - Fußball oder Mathematik T2 - Alma Mater Aquensis : Jahresbericht Y1 - 1971 SP - 110 EP - 114 ER - TY - CHAP A1 - Helsper, Christoph A1 - Fissan, H. J. A1 - Franzen, H. ED - Benarie, Michel M. T1 - Particle Size Distributions of Combustion Aerosols T2 - Atmospheric Pollution 1978 : Proceedings of the 13th International Colloquium; 25-28 April 1978; Paris, France; Edited by Michel M. Benarie N2 - It has been observed that carcinogenic polycyclic aromatic hydrocarbons (PAH) are present in the atmosphere. Combustion processes are considered the most important sources for PAH. Among these, the burning of coal produces the highest emission, but in cities with high traffic density and low meteorological exchange activities, vehicle emissions determine the immission situation, especially in narrow streets. For estimating the potential health effects caused by PAH, it is sufficient to characterize the emission of PAH with respect to their physical state, concentrations, and, as far as the particulate phase is concerned, size distribution. The size distribution is important for transport phenomena, inhalation, and deposition in the respiratory tract. These parameters mainly depend on the combustion system, on system operating conditions, on the exhaust system, and on exhaust cooling conditions. At exhaust-gas temperatures in the range of ambient air temperatures, almost the whole emission of PAH is made up of particulate matter. Y1 - 1978 SN - 0-444-41691-9 U6 - http://dx.doi.org/10.1016/S0166-1116(08)71583-8 SP - 263 EP - 266 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Hirsch, G. A1 - Wahle, Michael T1 - Auslegungskriterien für Dynamische Schwingungsdämpfer für schwach gedämpfte elastische Strukturen unter Berücksichtigung einer der Masseverteilung nicht proportionalen Zusatzdämpfung T2 - Hans Ebner : Gedächtnis-Kolloquium am 27./28. Oktober 1977 in Aachen. - (Mitteilung aus dem Institut für Leichtbau, Aachen ; 1) Y1 - 1978 SP - 374 EP - 400 CY - Aachen ER - TY - CHAP A1 - Cresser, J. D. A1 - Häger, J. A1 - Leuchs, G. A1 - Rateike, Franz-Matthias A1 - Walther, H. T1 - Resonance fluorescence of atoms in strong monochromatic laser fields T2 - Dissipative systems in quantum optics. Ed. by Rodolfo Bonifacio. Topics in current physics. Vol. 27 N2 - The investigation of atomic resonance fluorescence has always been of special interest as a means for the determination of atomic parameters. In addition, information on the interaction mechanism between atoms and radiation can be obtained. In the standard fluorescence experiment the frequency distribution of the incident photons is larger than the natural width of the respective transition; as a consequence the correlation time in the photon-atom interaction is determined by the lifetime of the atoms in the excited state. With the development of lasers and especially of tunable dye lasers in recent years it became possible to study the case where the incident radiation has a spectral distribution which is narrower than the natural width. This corresponds to a correlation time of the incoming light wave which is much longer than the excited-state lifetime. In this chapter a survey of experiments on the resonance fluorescence of atoms in monochromatic laser fields will be given. Y1 - 1982 SN - 978-3-642-81719-9 U6 - http://dx.doi.org/10.1007/978-3-642-81717-5_3 SP - 21 EP - 59 PB - Springer CY - Berlin ER - TY - CHAP A1 - Alt, Helmut T1 - Analog anzeigende Digitaluhr T2 - FH-Texte ; 36 : Berichte aus dem Fachbereich Elektrotechnik Aachen Y1 - 1983 SP - 98 EP - 104 PB - Fachhochschule Aachen CY - Aachen ER - TY - CHAP A1 - Dören, Horst-Peter A1 - Wernicke, K. T1 - Einfluß der Schweißparameter beim Plasmaauftragschweißen mit Pulvern T1 - Influence of the welding parameters in plasma-arc overlay welding with powder T2 - Schweißen und Schneiden '85 = Welding and Cutting '85. Vorträge der Großen Schweißtechnischen Tagung in Essen vom 11. bis 13. September 1985. Veranst.: Deutscher Verband für Schweißtechnik (DVS). DVS-Berichte. 100 Y1 - 1985 SN - 3-87155-405-7 SP - 72 EP - 76 PB - Dt. Verl. für Schweißtechnik (DVS) CY - Düsseldorf ER - TY - CHAP A1 - Dören, Horst-Peter A1 - Plaschka, K. A1 - Pohl, M. T1 - Die Untersuchung von Schutzgasschweißdrähten mit Hilfe des Rasterelektronenmikroskops T1 - Investigation of wires for gas shielded arc welding using the scanning electron microscope T2 - Fortschritte in der Metallographie. Berichte der 7. Internationalen Metallographie-Tagung Leoben 15. bis 17. Oktober 1986. Sonderbände der Praktischen Metallographie. 18 Y1 - 1987 SN - 0343-3579 SP - 333 EP - 345 PB - Riederer CY - Stuttgart ER - TY - CHAP A1 - Dören, Horst-Peter T1 - Nichtrostende Stähle T2 - Jahrbuch Schweißtechnik. 1988 Y1 - 1987 SN - 0935-0292 SP - 188 EP - 203 PB - Dt. Verl. für Schweißtechnik (DVS) CY - Düsseldorf ER - TY - CHAP A1 - Mertens, Josef A1 - Becker, K. ED - Ballmann, Josef T1 - Numerical solution of flow equations : an aircraft designer's view T2 - Nonlinear hyperbolic equations - theory, computation methods, and applications : proceedings of the 2nd International Conference on Nonlinear Hyperbolic Problems, Aachen, FRG, March 14 to 18, 1988. - (Notes on Numerical Fluid Mechanics ; 24) N2 - Today the most accurate and cost effective industrial codes used in aircraft design are based on the full potential equation coupled with boundary layer equations. However, these are not capable to solve complicated three-dimensional problems of vortical flows and shocks. On the other hand Euler and Navier-Stokes codes are too expensive and not accurate enough for design purposes, especially in regard of drag and interference prediction. The reasons for these deficiencies are investigated and a way to overcome them by future developments is demonstrated. Y1 - 1989 SN - 3-528-08098-1 U6 - http://dx.doi.org/10.1007/978-3-322-87869-4_41 N1 - International Conference on Nonlinear Hyperbolic Problems <3, 1988, Aachen> SP - 403 EP - 412 PB - Vieweg CY - Braunschweig ER - TY - CHAP A1 - Kurbel, Karl A1 - Pietsch, Wolfram ED - Kurbel, Karl ED - Mertens, Peter ED - Scheer, August W. T1 - Projektmanagementebenen bei evolutionärer Softwareentwicklung T2 - Interaktive betriebswirtschaftliche Informations- und Steuerungssysteme Y1 - 1989 SN - 3-11-012100-X U6 - http://dx.doi.org/10.1515/9783110847055-013 SP - 261 EP - 285 PB - De Gruyter CY - Berlin ER - TY - CHAP A1 - Dören, Horst-Peter T1 - Das Schweißen von Austenit-Ferrit-Verbindungen T2 - Jahrbuch Schweißtechnik. 1991 Y1 - 1990 SN - 3-87155-725-0 SP - 57 EP - 63 PB - DVS-Verlag CY - Düsseldorf ER - TY - CHAP A1 - Meliß, Michael T1 - Trends und Schwerpunkte bei der Entwicklung regenerativer Energieträger T2 - Technische Perspektiven und gesellschaftliche Entwicklungen : Trends und Schwerpunkte der Forschung in der Bundesrepublik Deutschland / Ulrich Widmaier; Thomas König (Hrsg.). - (Studien zur gesellschaftlichen Entwicklung ; 1) Y1 - 1990 SN - 3-7890-1891-0 SP - 279 EP - 306 PB - Nomos-Verl.-Ges. CY - Baden-Baden ER - TY - CHAP A1 - Pietsch, Wolfram T1 - Flexibilisierung des betrieblichen Software-Projektmanagements T2 - Beiträge zum Projektmanagement-Forum 90 : vom 19. - 21. September 1990 in Aachen Y1 - 1990 SN - 3-924841-10-1 SP - 345 EP - 355 PB - Gesellschaft für Projektmanagement INTERNET Deutschland e.V. CY - München ER - TY - CHAP A1 - Koller, R. A1 - Stellberg, Michael T1 - Schnappverbindungen T2 - Handbuch der Verbindungstechnik / hrsg. von Carl-Otto Bauer Y1 - 1991 SN - 3-446-14609-1 SP - 294 EP - 324 PB - Hanser CY - München ER - TY - CHAP A1 - Özdil, S. A1 - Berndt, Heinz A1 - Höcker, Hartwig T1 - Systematische Erfassung der Beständigkeit von Ryton-, P84- und Dralon ATF 1063-Fasern unter Einwirkung verschiedener NOx-Konzentrationen in einem definierten Temperaturintervall T2 - Schriftenreihe des Deutschen Wollforschungsinstitutes an der Technischen Hochschule Aachen e.V. Y1 - 1991 SN - 0930-3723 IS - 107 SP - 89 EP - 129 PB - Dt. Wollforschungsinstitut CY - Aachen ER - TY - CHAP A1 - Gidom, D. A1 - Pietsch, Wolfram T1 - Integrierte Steuerung von Bauprojekten durch Expertensysteme T2 - Dortmunder Expertensystemtage '91 : in Verbindung mit dem 3. Anwenderforum des KI-Verbundes NRW Y1 - 1991 SN - 3-88585-998-X SP - 356 EP - 365 PB - TÜV Rheinland CY - Köln ER - TY - CHAP A1 - Frewer, Hans A1 - Meliß, Michael T1 - Stromerzeugung - Perspektiven der Kraftwerkstechnik T2 - Die Zukunft der Stromversorgung / Alfred Voß (Hrsg.) Y1 - 1992 SN - 3-8022-0299-6 SP - 49 EP - 117 PB - Verlags- und Wirtschaftsgesellschaft der Elektrizitätswerke CY - Frankfurt a. M. ER - TY - CHAP A1 - Pietsch, Wolfram A1 - Siedentopf, Jukka A1 - Teubner, Alexander ED - Gaul, Wolfgang ED - Bachem, Achim ED - Habenicht, Walter ED - Runge, Walter ED - Stahl, Wolfgang W. T1 - Vergleich konnektionistischer Modelle und konventioneller Optimierungsverfahren am Beispiel der Maschinenbelegungsplanung T2 - Operations Research Proceedings 1991 / Papers of the 20th Annual Meeting = Vorträge der 20. Jahrestagung N2 - Für die Erstellung von Maschinenbelegungsplanen wurden im Operations Research aufwendige Optimierungsverfahren konzipiert und entsprechende Programme entwickelt. Maschinenbelegungsprobleme sind klassische Vertreter der Klasse der np-vollständigen Probleme, also sichere Kandidaten für kombinatorische Explosion der Lösungsalternativen. Deshalb ist der Einsatz konventioneller Planungssysteme wegen der hohen Rechneranforderungen der gängigen Verfahren an die Hardware oft nicht praktikabel. Y1 - 1992 SN - 978-3-642-46773-8 (Online) SN - 978-3-540-55410-3 (Print) U6 - http://dx.doi.org/https://doi.org/10.1007/978-3-642-46773-8_58 N1 - Part of the book series: Operations Research Proceedings (ORP, volume 1991) SP - 223 PB - Springer CY - Berlin ; Heidelberg ER - TY - CHAP A1 - Meliß, Michael T1 - Regenerative Energiequellen T2 - Energie - Technik - Umwelt : Festschrift : Herrn Professor Dr.-Ing. Hermann Unger zum 60. Geburtstag gewidmete Arbeiten / Ruhr-Universität Bochum, [Institut für Energietechnik], Lehrstuhl für Nukleare und Neue Energiesysteme. Hrsg.: U. Brockmeier Y1 - 1994 SP - 287 EP - 298 PB - Ruhr-Universität Bochum CY - Bochum ER - TY - CHAP A1 - Medlin, L. K. A1 - Barker, G. L. A. A1 - Baumann, Marcus A1 - Hayes, P. K. T1 - Molecular biology and systematics T2 - The Haptophyte Algae (Special volume / Systematics Association : 51) Y1 - 1994 SN - 0-19-857772-9 SP - 393 EP - 411 PB - Clarendon Press CY - Oxford ER - TY - CHAP A1 - Fabo, Sabine A1 - Eisenbeis, Manfred ED - Weber, Hermann T1 - Medienkultur : die mediale Konstruktion von Wirklichkeit T2 - Globalisierung der Zivilisation und überlieferte Kulturen : 28. - 30. April 1995 Y1 - 1995 SN - 3-926288-10-8 N1 - Jahresakademie / Katholischer Akademischer Ausländer-Dienst, KAAD ; [9] PB - Katholischer Akademischer Ausländer-Dienst CY - Bonn ER - TY - CHAP A1 - Bechstedt, U. A1 - Berg, Georg P. A. A1 - Hacker, U. A1 - Hardt, Arno A1 - Hürlimann, W. A1 - Maier, R. A1 - Martin, S. A1 - Meissburger, J. A1 - Römer, J. G. M. A1 - Possen, P. von A1 - Sagefka, T. T1 - BIG KARL and COSY T2 - The art and science of magnet design. A Festschrift in honor of Klaus Halbach. Vol. 1 Y1 - 1995 SP - 19 EP - 28 PB - Lawrence Berkeley Lab., Univ. of California CY - Berkeley, CA. ER - TY - CHAP A1 - Aydin, I. A1 - Dören, Horst-Peter A1 - Küpper, H. T1 - Plasma-Auftragschweißen mit Wolframschmelzkarbid-haltigen Metallpulvern und ihre Einsatzgebiete T1 - PTA surfacing with tungsten molten carbides containing metal powders and the area of their applications T2 - Thermische Spritzkonferenz = Thermal Spraying Conference. Erich Lugscheider [Hrsg.] DVS-Berichte 175 Y1 - 2013 SN - 3-87155-480-4 SP - 137 EP - 142 PB - DVS-Verlag CY - Düsseldorf ER - TY - CHAP A1 - Butenweg, Christoph A1 - Ebenau, C. T1 - Entwicklung eines objekt-orientierten FE-Programms T2 - Forum Bauinformatik - Junge Wissenschaftler forschen, Cottbus '96 Y1 - 1996 SN - 978-3-18-313504-2 N1 - Fortschritt-Berichte VDI : Reihe 4, Bauingenieurwesen, Band 135 SP - 60 EP - 65 PB - VDI-Verlag CY - Düsseldorf ER - TY - CHAP A1 - Dautzenberg, H. A1 - Groß, Rolf Fritz A1 - Renz, Ulrich ED - Jamal, Rahman T1 - Meßtechnik auf dem Prüfstand: Forschung zur Heißgasfiltration T2 - Virtuelle Instrumente in der Praxis. Begleitband zum Kongress VIP 1996 N2 - Im Rahmen von Forschungsvorhaben des BMBF und verschiedener Industriepartner betreibt der Lehrstuhl für Wärmeübertragung und Klimatechnik der RWTH Aachen Pilotanlagen und Prüfstände für Untersuchungen auf dem Gebiet der Heißgasfiltration mit keramischen Filterelementen. Als wesentlicher Garant für den Erfolg der Forschungsarbeit muß die auf das jeweilige Projekt genau abgestimmte Meß- und Regelungstechnik angesehen werden. Hierbei zählt neben der Auswahl geeigneter Hardwarekomponenten auch die Softwareentwicklung unter einer leistungsstarken und zuverlässigen Programmierumgebung. Anhand des Aufbaus dreier Versuchsanlagen im Technikumsmaßstab soll das Anforderungsprofil an die Meßtechnik bis hin zur Umsetzung innerhalb der Anlage skizziert werden. Der Heißgasfiltrationsprüfstand im Heizkraftwerk der RWTH Aachen dient der Beobachtung des Reinigungsverhaltens keramischer Filterelemente bei der Heißgasentstaubung im Temperaturbereich bis 850 Grad C. Wesentlich für die Meßwerterfassung ist hierbei die Kopplung eines Orion-Datenloggers der Firma Schlumberger mit LabView 4.0. Im Hochtemperaturofen des Lehrstuhls werden instationäre Druckmessungen an einer keramischen Filterkerze während eines Abreinigungsimpulses bei 950 Grad C mit hoher Samplingrate durchgeführt. Hierbei übernimmt eine durch LabView 4.0 angesteuerte E-Series Karte der Firma National Instruments die Signalaufnahme. Die katalytische Schadstoffreduktion und Entstaubung heißer Rauchgase bei 900 Grad C sind Ziele der Untersuchungen in einer erstellten Versuchsanlage mit einem Quarzglasreaktor. Die Signalerfassung und -konditionierung erfolgt über SCXI in Verbindung mit LabView 4.0, die Steuerung der Anlage übernehmen zwei Multifunktionskarten (National Instruments). KW - keramischer Werkstoff KW - Filter (Stofftrennung) KW - Filtration KW - Entstaubung KW - Staubfilter Y1 - 1996 N1 - 5.-6. November 1996 Forum der Technik München, Germany SP - 202 EP - 208 PB - National Instruments Germany CY - München ER - TY - CHAP A1 - Mertens, Josef ED - Sobieczky, H. T1 - Aerodynamic multi point design challenge T2 - New design concepts for high speed air transport.- (Courses and lectures / International Centre for Mechanical Sciences ; 366) N2 - In the chapter “Son of Concorde, a Technology Challenge” one of the new challenges for a Supersonic Commercial Transport (SCT) is multi-point design for the four main design points: - supersonic cruise - transonic cruise - take-off and landing - transonic acceleration. KW - Drag Reduction KW - Pitching Moment KW - Leading Edge Vortex KW - Wave Drag KW - Variable Geometry Y1 - 1997 SN - 3-2118-2815-X U6 - http://dx.doi.org/10.1007/978-3-7091-2658-5_4 SP - 53 EP - 67 PB - Springer CY - Wien [u.a.] ER - TY - CHAP A1 - Mertens, Josef ED - Sobieczky, H. T1 - Required aerodynamic technologies T2 - New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366) N2 - In the preceeding chapters on “Son of Concorde, a Technology Challenge” and “Aerodynamic Multipoint Design Challenge” it was explained, that a well balanced contribution of new technologies in all major disciplines is required for realisation of a new Supersonic Commercial Transport (SCT). One of these technologies - usually one of the most important for aircraft-is aerodynamics. Here, the required “pure” aerodynamic technologies are specified in more detail, according to our present knowledge. Increasing insight into the problems may change the balance of importance of the individual technologies and may require some more contributions. We must never confine our knowledge to the knowledge base of an expert at a given time, but must stay open for new insights. KW - Mach Number KW - Wind Tunnel KW - Supersonic Flow KW - Pitching Moment KW - Wave Drag Y1 - 1997 SN - 3-2118-2815-X U6 - http://dx.doi.org/10.1007/978-3-7091-2658-5_5 SP - 69 EP - 96 PB - Springer CY - Wien [u.a.] ER - TY - CHAP A1 - Mertens, Josef ED - Sobieczky, H. T1 - Certification of supersonic civil transports T2 - New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366) N2 - Since certification of Concorde new certification standards were introduced including many new regulations to improve flight safety. Most of these standards are to prevent severe accidents in the future which happened in the past (here: after Concorde’s certification). A new SCT has to fulfill these standards, although Concorde had none of these accidents. But accidents - although they sometimes occurred only for a specific aircraft type - have to be avoided for any (new) aircraft. Because of existing aircraft without typical accident types having demonstrated their reliability, they are allowed to go on based on their old certification; although sometimes new rules prevent accident types which are not connected to specific aircraft types - like e.g. evacuation rules. Anyway, Concorde is allowed to fly based on its old certification, and hopefully in the future will fly as safely as in the past. But a new SCT has to fulfill updated rules like any other aircraft, and it has to be “just another aircraft” [75]. KW - Noise Exposure KW - Evacuation Rule KW - Severe Accident KW - Certification Rule KW - Thermal Fatigue Testing Y1 - 1997 SN - 3-2118-2815-X U6 - http://dx.doi.org/10.1007/978-3-7091-2658-5_6 SP - 97 EP - 103 PB - Springer CY - Wien [u.a.] ER - TY - CHAP A1 - Mertens, Josef ED - Sobieczky, H. T1 - Supersonic laminar flow T2 - New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366) N2 - Supersonic transports are very drag sensitive. Technology to reduce drag by application of laminar flow, therefore, will be important; it is a prerequisite to achieve very long range capability. In earlier studies it was assumed that SCTs would only become possible by application of laminar flow [376]. But today, we request an SCT to be viable without application of laminar flow in order to maintain its competitiveness when laminar flow becomes available for subsonic and supersonic transports. By reducing fuel burned, laminar flow drag reduction reduces size and weight of the aircraft, or increases range capability -whereas otherwise size and weight would grow towards infinity. Transition mechanisms from laminar to turbulent state of the boundary layer flow (ALT, CFI, TSI) function as for transonic transports, but at more severe conditions: higher sweep angles, cooled surfaces; higher mode instabilities (HMI) must at least be taken into account, although they may not become important below Mach 3. Hitherto there is a worldwide lack of ground test facilities to investigate TSI at the expected cruise Mach numbers between 1.6 and 2.4; in Stuttgart, Germany one such facility -a Ludwieg tube- is still in the validation phase. A quiet Ludwieg tunnel could be a favourable choice for Europe. But it will require a new approach in designing aircraft which includes improved theoretical predictions, usage of classical wind tunnels for turbulent flow and flight tests for validation. KW - Wind Tunnel KW - Flight Test KW - Supersonic Wind Tunnel KW - Parabolized Stability Equation Y1 - 1997 SN - 3-2118-2815-X U6 - http://dx.doi.org/10.1007/978-3-7091-2658-5_18 SP - 275 EP - 290 PB - Springer CY - Wien [u.a.] ER - TY - CHAP A1 - Mertens, Josef ED - Sobieczky, H. T1 - Son of Concorde, a technology challenge T2 - New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366) N2 - Concorde (Figure 9) is the only supersonic airliner which has been introduced into regular passenger service. It is still in service at British Airways and Air France without any flight accidents, and probably will stay in service for at least for ten more years. KW - Technology Challenge KW - Multidisciplinary Design Optimization KW - Specific Fuel Consumption KW - Engine Efficiency KW - Sonic Boom Y1 - 1997 SN - 3-2118-2815-X U6 - http://dx.doi.org/10.1007/978-3-7091-2658-5_3 SP - 31 EP - 51 PB - Springer CY - Wien [u.a.] ER - TY - CHAP A1 - Mertens, Josef T1 - Reduction of aerodynamic drag (RaWid)-Status after the first year of the program T2 - New results in numerical and experimental fluid mechanics. - (Notes on numerical fluid mechanics ; 60) N2 - The technology programme “Reduction of aerodynamic drag (RaWid)” for high speed aerodynamics at Daimler-Benz Aerospace Airbus is sponsered by the German ministry for education, research and technology since July 1, 1995. Connected to this industrial programme are the cooperation programmes “MEGAFLOW” under leadership of the DLR and “Transition” by the DFG, and several contributions by DLR and universities. The programme is oriented towards technologies required for a MEGALINER which gains momentum by the ambitious plans for a new large Airbus A3XX. In the first year new technological steps were undertaken in theory, design and experiment. Some critical steps were verified by wing designs checked in wind tunnel tests. KW - Wind Tunnel KW - Aerodynamic Drag KW - Flight Test KW - Friction Drag Y1 - 1997 SN - 3-528-06960-0 U6 - http://dx.doi.org/10.1007/978-3-322-86573-1_2 SP - 7 EP - 14 PB - Vieweg CY - Braunschweig [u.a.] ER - TY - CHAP A1 - Lindemann, Markus A1 - Klein, Stefan T1 - Die Nutzung von Internet-Diensten im Rahmen des Elektronischen Datenaustauschs - Architekturvarianten und ein Anwendungsszenario T2 - Wirtschaftsinformatik '97 - Internationale Geschäftstätigkeit auf der Basis flexibler Organisationsstrukturen und leistungsfähiger Informationssysteme / Hermann Krallmann (Hrsg.) Y1 - 1997 SN - 3-7908-0999-3 SP - 513 EP - 531 PB - Physica-Verlag CY - Heidelberg ER - TY - CHAP A1 - Lincke, D.-M. A1 - Haertsch, P. A1 - Hoffmann, C. P. A1 - Lindemann, Markus T1 - Electronic Commerce Plattformen für den Werkzeugmaschinenbau T2 - Internet im Industriegütermarketing - Status quo und Entwicklungsperspektiven am Beispiel der Schweizer Werkzeugmaschinen-Industrie / Johannes Dickel ... (Hrsg.) Thexis-Fachbericht für Marketing. 97,4 Y1 - 1997 SN - 3-908545-38-2 SP - 60 EP - 85 PB - Thexis CY - St. Gallen ER - TY - CHAP A1 - Wahle, Michael ED - Reimerdes, Hans-G. T1 - Strukturmechanische Auslegung von Elastomer-Bauteilen in der Schwingungstechnik T2 - Kolloquium anläßlich des 70. Geburtstags von H. Öry : [29.09.1997 - 30.09.1997, Kármán-Auditorium, Hörsaal FO5, RWTH Aachen] Y1 - 1997 SP - 175 EP - 188 PB - Inst. für Leichtbau CY - Aachen ER - TY - CHAP A1 - Brandt, D. A1 - Güsken, J. A1 - Büchen, W. A1 - [u.a.], A1 - Wahle, Michael T1 - Konstruieren mit Aluminium [Kapitel 4] T2 - Aluminium-Taschenbuch / Hrsg.: Aluminium-Zentrale Düsseldorf. - Bd. 3: Weiterverarbeitung und Anwendung Y1 - 1997 SN - 3-87017-243-6 SP - 359 EP - 544 PB - Aluminium-Verlag CY - Düsseldorf ET - 15. Auflage ER - TY - CHAP A1 - Meliß, Michael A1 - Späte, Frank T1 - Berechnung von Sonnenstand und -strahlung T2 - Regenerative Energiequellen : Praktikum / ed. Michael Meliß Y1 - 1997 SN - 3-540-63218-2 U6 - http://dx.doi.org/10.1007/978-3-642-60864-3_2 SP - 5 EP - 22 PB - Springer CY - Berlin ER - TY - CHAP A1 - Meliß, Michael A1 - Späte, Frank T1 - Auslegung von solarthermischen Anlagen T2 - Regenerative Energiequellen : Praktikum / ed. Michael Meliß Y1 - 1997 SN - 3-540-63218-2 U6 - http://dx.doi.org/10.1007/978-3-642-60864-3_3 SP - 23 EP - 47 PB - Springer CY - Berlin ER - TY - CHAP A1 - Borchert, Jörg T1 - Der Elektrizitätsmarkt in Indonesien und Beteiligungsmöglichkeiten privater Unternehmen T2 - Investitionsführer ASEAN, Indochina, 1997 : Brunei, Indonesien, Kambodscha, Laos, Malaysia, Myanmar, Philippinen, Singapur, Thailand, Vietnam Y1 - 2015 SP - 42 EP - 52 PB - Berliner Bank AG CY - Berlin ET - Stand: Mai 1997 ER - TY - CHAP A1 - Groß, Rolf Fritz A1 - Müller, D. A1 - Herting, D. A1 - Schneemann, A. A1 - Renz, Ulrich ED - Rahman, Jamal ED - Jaschinski, Hans T1 - Modulare Messdatenerfassung in Forschung und Lehre T2 - Virtuelle Instrumente in der Praxis : Begleitband zum Kongress VIP '97 N2 - The Lehrstuhl für Wärmeübertragung und Klimatechnik at the Aachen University of Technology operates several test facilities to investigate fundamentals of heat and mass transfer supported by the Deutsche Forschungsgemeinschaft, the Minister für Forschung und Technologie and the industry. In order to get high-resolution and reproselection of hardware components is as critical as the design of software routines to perform successful and accurate measurements. In the following the development of the measurement and control system for three different test facilities is presented and discussed. Special attention is given to the education of students within the framework of laboratories and scientific experiments. Y1 - 1997 SN - 978-3-7785-2667-5 Pp. SP - 282 EP - 288 PB - Hüthig CY - Heidelberg ER - TY - CHAP A1 - Biener, Ernst T1 - Abfallwirtschaft T2 - Bautechnische Zahlentafeln : mit 225 Beispielen / Wendehorst. Hrsg. von Otto W. Wetzell. Bearb. von Hubert Achten ... - 28., neubearb. Aufl. Y1 - 1998 SN - 3-519-25002-0 SP - 1265 EP - 1292 PB - Teubner [u.a.] CY - Stuttgart [u.a.] ER - TY - CHAP A1 - Dören, Horst-Peter T1 - Aktuelle Fragen zur Schweißmetallurgie. Neue Werkstoffe und ihre schweißtechnische Verarbeitung = Current questions on welding metallurgy T2 - Jahrbuch Schweißtechnik '99 Y1 - 1998 SN - 3-87155-745-5 SP - 77 EP - 85 PB - DVS-Verlag CY - Düsseldorf ER - TY - CHAP A1 - Weber, Hans-Joachim T1 - Applied physics of compressible and incompressible fluids T2 - Critical care nephrology / [Hrsg.:] Claudio Ronco and Rinaldo Bellomo Y1 - 1998 SN - 978-94-010-6306-7 SP - 63 EP - 84 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Dikta, Gerhard T1 - Fundamentals of applied probability and basic statistics T2 - Critical care nephrology / [Hrsg.:] Claudio Ronco and Rinaldo Bellomo Y1 - 1998 SN - 978-94-010-6306-7 SP - 51 EP - 61 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Lindemann, Markus T1 - Unternehmerische Netzwerke und elektronische Märkte - Blicke in die Zukunft T2 - Produktionsmanagement und Informationslogistik - aktuelle Entwicklungen, Trends und Perspektiven. (Im focus) Y1 - 1998 PB - Orell Füssli CY - Zürich ER - TY - CHAP A1 - Meliß, Michael T1 - Regenerative Energieträger T2 - Lexikon der Bioethik / hrsg. im Auftr. der Görres-Gesellschaft von Wilhelm Korff. Bd. 3 Y1 - 1998 SP - 168 EP - 175 PB - Gütersloher Verlagshaus CY - Gütersloh ER - TY - CHAP A1 - Pietsch, Wolfram ED - Hummeltenberg, Wilhelm T1 - Kundenorientiertes Softwareprozeßmanagement T2 - Information management for business and competitive intelligence and excellence: Proceedings der Frühjahrstagung Wirtschaftsinformatik '98 N2 - In der betrieblichen Entwicklungspraxis klaffen Anspruch und Realität bei der Gestaltung betrieblicher Softwareentwicklungsprozesse auseinander. Nicht selten werden „Vorgehensmodelle“definiert, jedoch nicht konsequent oder nicht mit dem erwünschten Erfolg eingesetzt. Die Modellierung der Entwicklungsabläufe garantiert nicht deren effektive und effiziente Umsetzung; dazu ist ein „Prozeßmanagement“erforderlich. Die verfügbaren Prozeßmanagementansätze eignen sich für unterschiedliche Anwendungsfelder und Organisationskulturen, sind dementsprechend auch auf die Softwareentwicklung übertragbar, adressieren jedoch nur bedingt den zentralen Erfolgsfaktor betrieblicher Softwareentwicklung: die Zufriedenheit der Anwender als Kunden der Softwareentwicklung. Der Schlüssel für erfolgreiche Softwareentwicklungsprozesse liegt nicht im Prozeßmanagement allein, sondern in dessen Ausgestaltung mit Blick auf den Kunden. Ansatzpunkte für ein kundenorientiertes Softwareprozeßmanagement sind die Etablierung einer Kunden/Lieferantenbeziehung, die Fokussierung und Differenzierung der Entwicklungsprozesse, die Benutzerinvolvierung, Simultaneous Engineering und die gezielte Identifikation, Integration und Kooperation der „Stimme des Kunden“und der „Stimme des Ingenieurs“. Die Bewertung kundenorientierter Softwareprozesse wird diskutiert und Schlußfolgerungen für Forschung und Praxis skizziert. Y1 - 1998 SN - 978-3-528-05678-0 (Print) SN - 978-3-322-84950-2 (Online) U6 - http://dx.doi.org/10.1007/978-3-322-84950-2_22 SP - 301 EP - 311 PB - Vieweg+Teubner Verlag CY - Wiesbaden ER - TY - CHAP A1 - Luczak, Holger A1 - Wolf, Martin A1 - Schlick, Christopher A1 - Springer, J. A1 - Foltz, Christian ED - Nagl, Walter T1 - Personenorientierte Arbeitsprozesse und Kommunikationsforrnen T2 - Integration von Entwicklungssystemen in Ingenieuranwendungen : substantielle Verbesserung der Entwicklungsprozesse Y1 - 1999 SN - 3-540-63920-9 SP - 403 EP - 422 PB - Springer CY - Berlin ER - TY - CHAP A1 - Schwarte, Rudolf A1 - Heinol, Horst-Guenther A1 - Buxbaum, Bernd A1 - Ringbeck, Thorsten A1 - [u.a.], ED - Jähne, Bernd T1 - Principles of three-dimensional imaging techniques T2 - Sensors and imaging. - (Handbook of computer vision and applications ; Vol. 1) Y1 - 1999 SN - 0-12-379771-3 (Einzelbd.) SN - 0-12-379770-5 (Gesamtwerk) SP - 463 EP - 485 PB - Academic Press CY - San Diego ER - TY - CHAP A1 - Hoffmann, Christoph P. A1 - Lindemann, Markus T1 - Logistik und internetbasiertes Electronic Commerce T2 - Schweizer Logistik-Katalog : Logistik, fördern, lagern, verteilen. 1999 Y1 - 1999 SP - 16 EP - 19 PB - Binkert CY - Lauffenburg ER - TY - CHAP A1 - Kruska, Martin A1 - Kuperjans, Isabel T1 - Análisis Thermodinámicos : [Capítulo 3.3] T2 - Uso racional de energía : eficiencia energética y energías renovables. - (Manual para consultores y expertos) Y1 - 1999 SP - 3.3-1 EP - 3.3-15 PB - Ministerio de Energía y Minas CY - Lima ER -