TY - JOUR A1 - Baader, Fabian A1 - Boxberg, Marc S. A1 - Chen, Qian A1 - Förstner, Roger A1 - Kowalski, Julia A1 - Dachwald, Bernd T1 - Field-test performance of an ice-melting probe in a terrestrial analogue environment JF - Icarus N2 - Melting probes are a proven tool for the exploration of thick ice layers and clean sampling of subglacial water on Earth. Their compact size and ease of operation also make them a key technology for the future exploration of icy moons in our Solar System, most prominently Europa and Enceladus. For both mission planning and hardware engineering, metrics such as efficiency and expected performance in terms of achievable speed, power requirements, and necessary heating power have to be known. Theoretical studies aim at describing thermal losses on the one hand, while laboratory experiments and field tests allow an empirical investigation of the true performance on the other hand. To investigate the practical value of a performance model for the operational performance in extraterrestrial environments, we first contrast measured data from terrestrial field tests on temperate and polythermal glaciers with results from basic heat loss models and a melt trajectory model. For this purpose, we propose conventions for the determination of two different efficiencies that can be applied to both measured data and models. One definition of efficiency is related to the melting head only, while the other definition considers the melting probe as a whole. We also present methods to combine several sources of heat loss for probes with a circular cross-section, and to translate the geometry of probes with a non-circular cross-section to analyse them in the same way. The models were selected in a way that minimizes the need to make assumptions about unknown parameters of the probe or the ice environment. The results indicate that currently used models do not yet reliably reproduce the performance of a probe under realistic conditions. Melting velocities and efficiencies are constantly overestimated by 15 to 50 % in the models, but qualitatively agree with the field test data. Hence, losses are observed, that are not yet covered and quantified by the available loss models. We find that the deviation increases with decreasing ice temperature. We suspect that this mismatch is mainly due to the too restrictive idealization of the probe model and the fact that the probe was not operated in an efficiency-optimized manner during the field tests. With respect to space mission engineering, we find that performance and efficiency models must be used with caution in unknown ice environments, as various ice parameters have a significant effect on the melting process. Some of these are difficult to estimate from afar. Y1 - 2023 U6 - https://doi.org/10.1016/j.icarus.2023.115852 N1 - Forschungsdaten hierzu: "Performance data of an ice-melting probe from field tests in two different ice environments" (https://opus.bibliothek.fh-aachen.de/opus4/frontdoor/index/index/docId/10890) IS - 409 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Gorzalka, Philip A1 - Dahlke, Dennis A1 - Göttsche, Joachim A1 - Israel, Martin A1 - Patel, Dhruvkumar A1 - Prahl, Christoph A1 - Schmiedt, Jacob Estevam A1 - Frommholz, Dirk A1 - Hoffschmidt, Bernhard A1 - Linkiewicz, Magdalena T1 - Building Tomograph–From Remote Sensing Data of Existing Buildings to Building Energy Simulation Input T2 - EBC, Annex 71, Fifth expert meeting, October 17-19, 2018, Innsbruck, Austria Y1 - 2018 ER - TY - PAT A1 - Berndt, Heinz A1 - Höcker, Hartwig A1 - Kuropka, Rolf A1 - Kinkel, Joachim T1 - Silane coated inorganic materials for chromatography : United States Patent Y1 - 1991 PB - [The United States Patent and Trademark Office] CY - [Alexandria, VA u.a.] ER - TY - JOUR A1 - Wilson, Ian D. A1 - Wilson, Claire E. A1 - Scheer, Nico A1 - Dickie, A.P. A1 - Schreiter, K. A1 - Wilson, E. M. A1 - Riley, R. J. A1 - Wehr, R. A1 - Bial, J. T1 - The Pharmacokinetics and Metabolism of Lumiracoxib in Chimeric Humanized and Murinized FRG Mice JF - Biochemical pharmacology Y1 - 2017 U6 - https://doi.org/10.1016/j.bcp.2017.03.015 SN - 1873-2968 VL - Volume 135 SP - 139 EP - 150 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Buxbaum, Bernd A1 - Schwarte, Rudolf A1 - Ringbeck, Thorsten ED - Kamerman, Gary W. T1 - Synchronization in spread spectrum laser radar systems based on PMD-DLL T2 - Laser radar technology and applications V : 26 - 28 April 2000, Orlando, USA. - (SPIE proceedings series ; 4035) Y1 - 2000 SN - 0-8194-3661-5 SN - 0038-7355 SN - 0361-0748 SN - 0277-786X N1 - Laser radar technology and applications <5, 2000, Orlando, Fla.> SP - 204 EP - 216 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Wolf, Martin R. A1 - Wiese, Ute T1 - A comparative transformation model for process changes using serious games T2 - 2013 IEEE 2nd International Conference on Serious Games and Applications for Health (SeGAH): proceedings of a meeting held 2-3 May 2013, Algarve, Portugal Y1 - 2013 SN - 978-1-4673-6164-4 U6 - https://doi.org/10.1109/SeGAH.2013.6665307 SP - 64 EP - 70 PB - Institute of Electrical and Electronics Engineers (IEEE) CY - Piscataway, NJ ER - TY - JOUR A1 - Hough, Lindsay B. A1 - Nalwalk, Julia W. A1 - Ding, Xinxin A1 - Scheer, Nico T1 - Opioid Analgesia in P450 Gene Cluster Knockout Mice: A Search for Analgesia-Relevant Isoforms JF - Drug Metabolism and Disposition Y1 - 2015 U6 - https://doi.org/10.1124/dmd.115.065490 SN - 1521-009x VL - 43 IS - 9 SP - 1326 EP - 1330 ER - TY - CHAP A1 - Laack, Walter van T1 - Schnittstelle Tod: Wo stehen wir nach 40 Jahren NTE-Forschung? Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:101:1-201603132912 SN - 978-3-936624-30-4 (Print-Ausgabe) SN - 978-3-936624-32-8 (Online-Ausgabe) N1 - Tagungsbeiträge des 4. Europäischen Seminars am 07. November 2015 in Aachen zum Thema Nahtoderfahrungen mit dem Serientitel: "Schnittstelle Tod" PB - van Laack GmbH CY - Aachen ER - TY - RPRT A1 - Adomeit, G. A1 - Willms, Herbert T1 - Experimental investigation of the acceleration of deflagration in wake flow : final report. - (Euratom-publications-EUR ; 9593 : Nuclear science and technology) Y1 - 1984 SN - 92-825-4699-3 PB - Commission of the European Communities CY - Luxembourg ER - TY - GEN A1 - Hering, T. A1 - Pasteur, A. A1 - Wollny, S. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Magnetische Separation von Gold-Nanopartikeln zur Gluconsäure-Produktion durch Hochgradient-Magnetseparation im Labormaßstab T2 - Chemie Ingenieur Technik N2 - Bei der Verarbeitung nachwachsender Rohstoffe entsteht aus Cellulose oder Stärke u. a. das wichtige Produkt Glucose. Diese niedermolekulare Kohlenhydratquelle wird üblicherweise als Substrat für biotechnologische und chemische Synthesen verwendet. Ein wirtschaftlich interessantes Oxidationsprodukt der Glucose ist Gluconsäure, die beispielsweise als Lebensmittelzusatzstoff (E 574), in der Medizin und Metallindustrie Verwendung findet. Die Umsetzung des Monosaccharids zu Gluconsäure erfolgt entweder durch mikrobielle Fermentation oder der Oxidation an heterogenen Katalysatoren. Die Zielsetzung der Studie ist die Untersuchung der Glucoseoxidation an magnetisierbaren Gold-Nanopartikeln unter nachfolgender Bypass-Separation des Katalysators mittels einer neuen Mini-HGMS-Einheit (Hochgradient-Magnetseparation). Dieser Filtertyp ermöglicht die selektive Trennung magnetischer Partikel aus Suspensionen mit hohem Feststoffgehalt oder Viskosität. Erste Ergebnisse zeigen eine Beladungskapazität des selbstkonstruierten Mini-HGMS von 550 mg goldbeschichteter magnetisierbarer Nanopartikel. Die Oxidation erfolgt bei einem pH-Wertvon 9, bei 40 °C und mit 100 mM Glucose in einem begasten Rührkesselreaktor. Das System soll zukünftig zum Katalysatorrecycling von hochviskosen und Feststoffbelasteten Produktströmen aus Bioraffinerien eingesetzt werden. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450265 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1501 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Engel, M. A1 - Bayer, H. A1 - Ulber, Roland A1 - Tippkötter, Nils T1 - Kommt es in Elektrofermentationen mit Clostridium acetobutylicum zu einer Eisenlimitierung? T2 - Chemie Ingenieur Technik N2 - Das strikt anaerobe Bakterium Clostridium acetobutylicum bildet die Lösemittel Aceton, Butanol und Ethanol (ABE-Fermentation). Im Fall einer Eisenlimitierung kommt es zusätzlich zu einer Riboflavinsekretion (RF), was durch die gelbe Färbung des Kulturüberstands erkennbar ist. In dieser Arbeit wurde beobachtet, dass während Elektrofermentationen mit C. acetobutylicum bei –600 mV eine gelbe Färbung auftritt. Es wurde deshalb untersucht, ob eine Eisenlimitierung im bio-elektrochemischen System (BES) vorliegt. Hierzu wurden die Flavinspezien bei Kultivierungen in Medien mit einer Eisenlimitierung bzw. mit ausreichend Eisen in Serumflaschen sowie im BES mit und ohne angelegtem Potenzial verglichen. In den Serumflaschenversuchen wurden RF und Flavinadenindinukleotid (FAD)-Konzentrationen von ‡ 20 mg L⁻¹ sowie Flavinmononukleotid (FMN)-Konzentrationen von ca. 5 mg L⁻¹ detektiert. Bei ausreichender Eisenverfügbarkeit hingegen wurden in den Serumflaschen fast keine Flavine sekretiert. Im BES bei –600 mV hingegen wurde auch in diesen Kulturüberständen FMN und FAD (1–5 mg L⁻¹ ),jedoch kein RF gemessen. Diese Ergebnisse zeigen, dass die Flavinbildung im BES mit angelegtem Potenzial nicht mit der Flavinbildung unter Eisenlimitierung in Serumflaschen korreliert. Andere Faktoren für eine mögliche Flavinbildung werden aktuell näher betrachtet. Y1 - 2018 U6 - https://doi.org/10.1002/cite.201855047 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung und 33. DECHEMA-Jahrestagung der Biotechnologen 2018, 10. - 13. September 2018, Eurogress Aachen VL - 90 IS - 9 SP - 1154 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Rupp, Matthias A1 - Schulze, Sven A1 - Kuperjans, Isabel T1 - Comparative life cycle analysis of conventional and hybrid heavy-duty trucks JF - World electric vehicle journal N2 - Heavy-duty trucks are one of the main contributors to greenhouse gas emissions in German traffic. Drivetrain electrification is an option to reduce tailpipe emissions by increasing energy conversion efficiency. To evaluate the vehicle’s environmental impacts, it is necessary to consider the entire life cycle. In addition to the daily use, it is also necessary to include the impact of production and disposal. This study presents the comparative life cycle analysis of a parallel hybrid and a conventional heavy-duty truck in long-haul operation. Assuming a uniform vehicle glider, only the differing parts of both drivetrains are taken into account to calculate the environmental burdens of the production. The use phase is modeled by a backward simulation in MATLAB/Simulink considering a characteristic driving cycle. A break-even analysis is conducted to show at what mileage the larger CO2eq emissions due to the production of the electric drivetrain are compensated. The effect of parameter variation on the break-even mileage is investigated by a sensitivity analysis. The results of this analysis show the difference in CO2eq/t km is negative, indicating that the hybrid vehicle releases 4.34 g CO2eq/t km over a lifetime fewer emissions compared to the diesel truck. The break-even analysis also emphasizes the advantages of the electrified drivetrain, compensating the larger emissions generated during production after already a distance of 15,800 km (approx. 1.5 months of operation time). The intersection coordinates, distance, and CO2eq, strongly depend on fuel, emissions for battery production and the driving profile, which lead to nearly all parameter variations showing an increase in break-even distance. Y1 - 2018 U6 - https://doi.org/10.3390/wevj9020033 SN - 2032-6653 VL - 9 IS - 2 SP - Article No. 33 PB - MDPI CY - Basel ER - TY - JOUR A1 - Kob, Malte A1 - Frauenrath, Tobias T1 - A system for parallel measurement of glottis opening and larynx position JF - Biomedical Signal Processing and Control N2 - The simultaneous assessment of glottal dynamics and larynx position can be beneficial for the diagnosis of disordered voice or speech production and swallowing. Up to now, methods either concentrate on assessment of the glottis opening using optical, acoustical or electrical (electroglottography, EGG) methods, or on visualisation of the larynx position using ultrasound, computer tomography or magnetic resonance imaging techniques. The method presented here makes use of a time-multiplex measurement approach of space-resolved transfer impedances through the larynx. The fast sequence of measurements allows a quasi simultaneous assessment of both larynx position and EGG signal using up to 32 transmit–receive signal paths. The system assesses the dynamic opening status of the glottis as well as the vertical and back/forward motion of the larynx. Two electrode-arrays are used for the measurement of the electrical transfer impedance through the neck in different directions. From the acquired data the global and individual conductivity is calculated as well as a 2D point spatial representation of the minimum impedance. The position information is shown together with classical EGG signals allowing a synchronous visual assessment of glottal area and larynx position. A first application to singing voice analysis is presented that indicate a high potential of the method for use as a non-invasive tool in the diagnosis of voice, speech, and swallowing disorders. KW - EGG KW - Transfer impedance KW - Tomography KW - Larynx position KW - Voice assessment Y1 - 2009 U6 - https://doi.org/10.1016/j.bspc.2009.03.004 SN - 1746-8108 VL - 4 IS - 3 SP - 221 EP - 228 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Mues genannt Koers, Lucas A1 - McNeil, S. W. A1 - Radchenko, V. A1 - Paulßen, Elisabeth A1 - Hoehr, Cornelia T1 - Production of Co-58m in a siphon-style liquid target on a medical cyclotron N2 - We present the production of 58mCo on a small, 13 MeV medical cyclotron utilizing a siphon style liquid target system. Different concentrated iron(III)-nitrate solutions of natural isotopic distribution were irradiated at varying initial pressures and subsequently separated by solid phase extraction chromatography. The radio cobalt (58m/gCo and 56Co) was successfully produced with saturation activities of (0.35 ± 0.03) MBq μA−1 for 58mCo with a separation recovery of (75 ± 2) % of cobalt after one separation step utilizing LN-resin. Y1 - 2023 U6 - https://doi.org/10.1016/j.apradiso.2023.110734 SN - 0969-8043 VL - 195 IS - Art. 110734 PB - Elsevier CY - Amsterdam ER - TY - RPRT A1 - Birmans, Katrin A1 - Tambornino, Philipp A1 - Ullrich, Anna Valentine T1 - Bevor Sie Coscine nutzen - Handreichung für Forschende an HAW N2 - Um die Forschungsdatenmanagement-Plattform Coscine optimal für Forschungsprojekte nutzen zu können, ist es sinnvoll, einige Fragen im Vorhinein zu klären. So können aufwendige Änderungen der Datenverwaltung im Nachhinein vermieden werden. Hierzu bietet die Handreichung hilfreiche Leitfragen und Erläuterungen für Forschende und FDM-Service-Personal an HAW in NRW (DH.NRW-Hochschulen). FDM-Service-Mitarbeitende können die Handreichung in ihrer Beratung zu Coscine einsetzen und mit der Eingabemaske in der Kopfzeile des Dokuments auf ihre Hochschule anpassen. Y1 - 2024 U6 - https://doi.org/10.5281/zenodo.12158546 N1 - Die Handreichung ist im Projekt Persist@HAW (FK: 16FDFH129), gefördert vom BMBF, entstanden. ER - TY - CHAP A1 - Dersch, Jürgen A1 - Geyer, Michael A1 - Herrmann, Ulf A1 - Jones, Scott A. A1 - Kelly, Bruce A1 - Kistner, Rainer A1 - Ortmanns, Winfried A1 - Pitz-Paal, Robert A1 - Price, Henry ED - Steinfeld, Aldo T1 - Trough integration into power plants : a study on the performance and economy of integrated solar combined cycle systems T2 - Proceedings of the 11th SolarPACES International Symposium on Concentrated Solar Power and Chemical Energy Technologies : September 4 - 6, 2002, Zurich, Switzerland / Paul Scherrer Institut, PSI; ETH, Eidgenössische Technische Hochschule Zürich Y1 - 2002 SN - 3-9521409-3-7 SP - 661 EP - 671 PB - Paul Scherrer Inst. CY - Villingen ER - TY - CHAP A1 - Mertens, Josef ED - Nitsche, Wolfgang T1 - Some important results of the technology programme RaWid T2 - New Results in Numerical and Experimental Fluid Mechanics : Contributions to the 11th AG STAB/DGLR Symposium Berlin, Germany 1998. - Vol. 2. - (Notes on Numerical Fluid Mechanics ; 72) Y1 - 1999 SN - 978-3-663-10903-7 (Print) SN - 978-3-663-10901-3 (Elektronisch) U6 - https://doi.org/10.1007/978-3-663-10901-3_41 SP - 315 EP - 322 PB - Springer Fachmedien CY - Wiesbaden ER - TY - JOUR A1 - Hafidi, Youssef A1 - El Hatka, Hicham A1 - Schmitz, Dominik A1 - Krauss, Manuel A1 - Pettrak, Jürgen A1 - Biel, Markus A1 - Ittobane, Najim T1 - Sustainable soil additives for water and micronutrient supply: swelling and chelating properties of polyaspartic acid hydrogels utilizing newly developed crosslinkers JF - Gels N2 - Drought and water shortage are serious problems in many arid and semi-arid regions. This problem is getting worse and even continues in temperate climatic regions due to climate change. To address this problem, the use of biodegradable hydrogels is increasingly important for the application as water-retaining additives in soil. Furthermore, efficient (micro-)nutrient supply can be provided by the use of tailored hydrogels. Biodegradable polyaspartic acid (PASP) hydrogels with different available (1,6-hexamethylene diamine (HMD) and L-lysine (LYS)) and newly developed crosslinkers based on diesters of glycine (GLY) and (di-)ethylene glycol (DEG and EG, respectively) were synthesized and characterized using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) and regarding their swelling properties (kinetic, absorbency under load (AUL)) as well as biodegradability of PASP hydrogel. Copper (II) and zinc (II), respectively, were loaded as micronutrients in two different approaches: in situ with crosslinking and subsequent loading of prepared hydrogels. The results showed successful syntheses of di-glycine-ester-based crosslinkers. Hydrogels with good water-absorbing properties were formed. Moreover, the developed crosslinking agents in combination with the specific reaction conditions resulted in higher water absorbency with increased crosslinker content used in synthesis (10% vs. 20%). The prepared hydrogels are candidates for water-storing soil additives due to the biodegradability of PASP, which is shown in an exemple. The incorporation of Cu(II) and Zn(II) ions can provide these micronutrients for plant growth. KW - micronutrients KW - swelling properties KW - biodegradable polymers KW - hydrogels KW - superabsorbent polymers KW - glycine KW - polyaspartic acid Y1 - 2024 U6 - https://doi.org/10.3390/gels10030170 SN - 2310-2861 VL - 10 IS - 3 SP - Artikel 170 PB - MDPI CY - Basel ER - TY - GEN A1 - Duwe, A. A1 - Sieker, T. A1 - Tippkötter, Nils A1 - Ulber, Roland T1 - Grasssilage als Substrat zur fermentativen Produktion organischer Säuren T2 - Chemie Ingenieur Technik N2 - Der zunehmende Bedarf an fossilen Rohstoffen bei gleichzeitig abnehmender Versorgungssicherheit führt zu einer intensiven Suche nach erneuerbaren Ressourcen. Ein vielversprechendes Ausgangsmaterial mit einer weltweiten Verfügbarkeit stellt Gras dar. In 2012 wurden in Deutschland 33 Millionen Tonnen (Heugewicht) Gras auf 4,82 Millionen Hektar Ackerland produziert, davon wurden 60,5 % siliert. Durch die Silierung kann Gras als Substrat zeitlich uneingeschränkt verfügbar sein, ohne dem Risiko des schnellen Verderbs ausgesetzt zu sein. Eine Schlüsselrolle im Rahmen des Silierprozesses nimmt die Produktion von Milchsäure ein. Milchsäure ist einbedeutendes biotechnologisches Produkt für die Lebensmittel- und die chemische Industrie. Im Rahmen dieser Arbeit wird die vollständige Umwandlung der fermentierbaren Zucker in der Silage zu Milchsäure angestrebt, um die maximale Ausbeute der organischen Säure zu erreichen. Im ersten Verfahrensschritt wird die Silage gepresst und der erhaltene Presskuchen einer Liquid-Hot-Water-Behandlung unterzogen. Durch diese einfache Vorbehandlung können hohe Glucoseausbeuten im nachfolgenden SSF-Schritt bei gleichzeitig geringem Enzymeinsatz und Chemikalienverbrauch realisiert werden. Zur Aufreinigung der Milchsäure wurden extraktive und chromatographische Methoden untersucht. Y1 - 2014 U6 - https://doi.org/10.1002/cite.201450345 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2014 und 31. DECHEMA-Jahrestagung der Biotechnologen, 30. September - 2. Oktober 2014, Eurogress Aachen VL - 86 IS - 9 SP - 1400 PB - Wiley-VCH CY - Weinheim ER - TY - GEN A1 - Tippkötter, Nils A1 - Pasteur, A. A1 - Ulber, Roland T1 - Magnetisch abtrennbare Gold-Nanopartikel zur katalytischen Zuckeroxidation T2 - Chemie Ingenieur Technik N2 - Glucose ist ein primäres Zwischenprodukt der Verarbeitung nachwachsender Rohstoffe, wie z. B. Cellulose. Die wertsteigernde Weiterverarbeitung des Monosaccharids erfolgt häufig in Form vonFermentationsprozessen, jedoch kann der Rohstoff auch für zahlreiche chemische Verarbeitungsstufen genutzt werden. Ein großtechnisch relevanter Prozess ist die Herstellung von Gluconsäure (GS), die u. a. als Nahrungsmittelzusatz (E 574) eingesetzt wird. Die Darstellung der Säure erfolgt durch Oxidation von Glucose mit magnetisierbarem Gold-Nano-Katalysator. Die Rückgewinnung des Katalysators aus der Reaktionslösung wurde unter Einwirkung eines Magnetfeldgradienten verwirklicht. Die Synthese der magnetischen Goldkatalysatoren (sowohl Trägerpartikel als auch Gold-Nanopartikel) wurde durch nass-chemische Fällungsreaktionen durchgeführt. Die Charakteristiken der neuen Materialen konnte durch Messungen des PCD-Potenzials, Laserbeugung und REM/EDX untersucht werden. So wurden u. a. Partikeldurchmesser von 25 lm und ein Goldgehaltvon 1,03 % ermittelt. Weiterhin wurden für die Goldkatalysatoren optimale Reaktionsbedingungen für die Glucoseoxidation im geregelten Rührkesselreaktor etabliert. Hierdurch konnten eine Produktselektivität von 100 % und eine Wiederverwendbarkeit der Partikel über mindestens zehn Zyklen erreicht werden. Y1 - 2012 U6 - https://doi.org/10.1002/cite.201250393 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet-Jahrestagung 2012 und 30. DECHEMA-Jahrestagung der Biotechnologen, 10. – 13. September 2012, Karlsruhe VL - 84 IS - 8 SP - 1328 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Treuling, Clemens A1 - Czarnecki, Christian A1 - Wolf, Martin R. T1 - Projekt WiLMo – Wirtschaftsinformatik Lehr- und Lernmodule T2 - Angewandte Forschung in der Wirtschaftsinformatik 2023 : Tagungsband zur 36. AKWI-Jahrestagung N2 - Die potenziellen Auswirkungen der Digitalisierung auf die Lehre sind seit langem Gegenstand ausführlicher Diskussionen innerhalb der Wirtschaftsinformatik (WI) (z. B. in Auth et al. 2021, Barton et al. 2019, Klotz et al. 2019). Nicht zuletzt der in nahezu allen Wirtschaftszweigen bestehende Mangel an qualifizierten Fachkräften lenkt den Diskurs auf einen verbesserten Zugang zu Bildung und gleichen Bildungschancen. Aus dieser Vision heraus und dem Schub der Digitalisierung entstehen Bildungskonzepte wie Open Educational Resources (OER), die gesellschaftlichen Problemen, wie dem des Fachkräftemangels, entgegenwirken sollen. Im Rahmen dieses Kurzbeitrags wird das Projekt WiLMo - "Wirtschaftsinformatik Lehr- und Lernmodule" vorgestellt. WiLMo wird im Rahmen von OERContent.nrw unter Beteiligung von sechs Hochschulen entwickelt und gefördert. Alle Projektbeteiligten arbeiten gemeinsam daran, einheitliche digitale Lehr- und Lernmaterialien im OER-Format für die Kernmodule der Wirtschaftsinformatik zu entwickeln und in garantiert hoher Qualität zur Verfügung zu stellen. KW - Wirtschaftsinformatik KW - Open Educational Resources (OER) KW - WiLMo Y1 - 2023 N1 - 36. AKWI-Jahrestagung, 11.09.2023 bis 13.09.2023, ausgerichtet von der Technischen Hochschule Wildau SP - 161 EP - 169 ER - TY - CHAP A1 - Donner, Ralf A1 - Rabel, Matthias A1 - Scholl, Ingrid A1 - Ferrein, Alexander A1 - Donner, Marc A1 - Geier, Andreas A1 - John, André A1 - Köhler, Christian A1 - Varga, Sebastian T1 - Die Extraktion bergbaulich relevanter Merkmale aus 3D-Punktwolken eines untertagetauglichen mobilen Multisensorsystems T2 - Tagungsband Geomonitoring Y1 - 2019 U6 - https://doi.org/10.15488/4515 SP - 91 EP - 110 ER - TY - CHAP A1 - Fissabre, Anke ED - Naujokat, Anke ED - Hake, Verena ED - Schindler, Bruno ED - Schötten, Björn T1 - Eine moderne Sainte-Chapelle in Köln. Otto Bartnings Stahlkirche auf der Pressa 1928 T2 - Baugedanken: Einsichten, Ansichten, Aussichten für Jan Pieper zum 80. Geburtstag Y1 - 2024 SN - 978-3-943164-87-9 SP - 66 EP - 81 PB - Geymüller Verag für Architektur CY - Aachen ER - TY - CHAP A1 - Ringbeck, Thorsten A1 - Buxbaum, Bernd T1 - A highly integrated monolithic electro-optical PLL in CMOS-technology (PMD-PLL) for communication and ranging systems T2 - Proceedings / OPTO 2000, 4th International Conference and Exhibition on Optoelectronics, Optical Sensors and Measuring Techniques : May 9 - 11, 2000, Erfurt Fair, Conference Centre Y1 - 2000 N1 - International Congress and Exhibition on Optoelectronics, Optical Sensors and Measuring Techniques <4, 2000, Erfurt> ; OPTO <4, 2000, Erfurt> SP - 235 EP - 239 PB - AMA Service GmbH CY - Wunsdorf ER - TY - CHAP A1 - Benner, Joachim ED - Peeken, Heinz T1 - Schwingungstechnische Dimensionierung von Maschinensätzen mit Stromrichtermotoren T2 - Antriebstechnisches Kolloquium '89 : Maschinen- und Anlagenüberwachung ; Elemente der Antriebstechnik im System ; neue Konzepte in der Antriebstechnik. - (Reihe IME-Leitfaden) Y1 - 1989 SN - 3-88585-639-5 N1 - Antriebstechnisches Kolloquium <3, 1989, Aachen> SP - 309 EP - 333 PB - Verl. TÜV Rheinland CY - Köln ER - TY - JOUR A1 - Benner, Joachim T1 - Schwingungsbelastung von drehzahlgeregelten Antrieben mit Stromrichtermotoren JF - Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V. Y1 - 1989 SN - 0341-2652 VL - 28 IS - 12 SP - 49 EP - 54 PB - Vereinigte Fachverl. CY - Mainz ER - TY - RPRT A1 - Esch, Thomas A1 - Funke, Harald A1 - Roosen, Petra T1 - SIoBiA – Safety Implications of Biofuels in Aviation N2 - Biofuels potentially interesting also for aviation purposes are predominantly liquid fuels produced from biomass. The most common biofuels today are biodiesel and bioethanol. Since diesel engines are rather rare in aviation this survey is focusing on ethanol admixed to gasoline products. The Directive 2003/30/EC of the European Parliament and the Council of May 8th 2003 on the promotion of the use of biofuels or other renewable fuels for transport encourage a growing admixture of biogenic fuel components to fossil automotive gasoline. Some aircraft models equipped with spark ignited piston engines are approved for operation with automotive gasoline, frequently called “MOGAS” (motor gasoline). The majority of those approvals is limited to MOGAS compositions that do not contain methanol or ethanol beyond negligible amounts. In the past years (bio-)MTBE or (bio-)ETBE have been widely used as blending component of automotive gasoline whilst the usage of low-molecular alcohols like methanol or ethanol has been avoided due to the handling problems especially with regard to the strong affinity for water. With rising mandatory bio-admixtures the conversion of the basic biogenic ethanol to ETBE, causing a reduction of energetic payoff, becomes more and more unattractive. Therefore the direct ethanol admixture is accordingly favoured. Due to the national enforcements of the directive 2003/30/EC more oxygenates produced from organic materials like bioethanol have started to appear in automotive gasolines already. The current fuel specification EN 228 already allows up to 3 % volume per volume (v/v) (bio-)methanol or up to 5 % v/v (bio-)ethanol as fuel components. This is also roughly the amount of biogenic components to comply with the legal requirements to avoid monetary penalties for producers and distributors of fuels. Since automotive fuel is cheaper than the common aviation gasoline (AVGAS), creates less problems with lead deposits in the engine, and in general produces less pollutants it is strongly favoured by pilots. But being designed for a different set of usage scenarios the use of automotive fuel with low molecular alcohols for aircraft operation may have adverse effects in aviation operation. Increasing amounts of ethanol admixtures impose various changes in the gasoline’s chemical and physical properties, some of them rather unexpected and not within the range of flight experiences even of long-term pilots. Y1 - 2010 N1 - Analysis of the safety implications of the use of biofuels (ethanol admixture) for piston engines and general aviation aircraft and assessment of potential environmental benefits. PB - EASA CY - Köln ER - TY - CHAP A1 - Tamaldin, Noreffendy A1 - Mansor, Muhd Rizuan A1 - Mat Yamin, Ahmad Kamal A1 - Bin Abdollah, Mohd Fazli A1 - Esch, Thomas A1 - Tonoli, Andrea A1 - Reisinger, Karl Heinz A1 - Sprenger, Hanna A1 - Razuli, Hisham ED - Bin Abdollah, Mohd Fadzli ED - Amiruddin, Hilmi ED - Singh, Amrik Singh Phuman ED - Munir, Fudhail Abdul ED - Ibrahim, Asriana T1 - Development of UTeM United Future Fuel Design Training Center Under Erasmus+ United Program T2 - Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia N2 - The industrial revolution IR4.0 era have driven many states of the art technologies to be introduced especially in the automotive industry. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South-East Asia (SEA). Indulging this situation, FH Joanneum, Austria together with European partners from FH Aachen, Germany and Politecnico Di Torino, Italy is taking initiative to close the gap utilizing the Erasmus+ United grant from EU. A consortium was founded to engage with automotive technology transfer using the European ramework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative, and high-quality training courses to increase graduate’s employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing Universityindustry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future. KW - Erasmus+ United KW - technology transfer KW - UTeM Engineering Knowledge Transfer Unit KW - Malaysian automotive industry Y1 - 2022 SN - 978-981-19-3178-9 SN - 978-981-19-3179-6 (E-Book) U6 - https://doi.org/10.1007/978-981-19-3179-6_50 SN - 2195-4356 N1 - 7th International Conference and Exhibition on Sustainable Energy and Advanced Material (ICE-SEAM 2021), Universiti Teknikal Malaysia Melaka (UTeM), Malaysia, in association with the Universitas Sebelas Maret (UNS), Indonesia, 23 November 2021 SP - 274 EP - 278 PB - Springer Nature CY - Singapore ER - TY - CHAP A1 - Rütters, René A1 - Bragard, Michael A1 - Dolls, Sarah T1 - The Inverted Rotary Pendulum: Facilitating Practical Teaching in Advanced Control Engineering T2 - 2024 IEEE Global Engineering Education Conference (EDUCON) N2 - This paper outlines a practical approach to teach control engineering principles, with an inverted rotary pendulum, serving as an illustrative example. It shows how the pendulum is embedded in an advanced course of control engineering. This approach is incorporated into a flipped-classroom concept, as well as classical teaching concepts, offering students practical experience in control engineering. In addition, the design of the pendulum is shown, using a Raspberry Pi as the target platform for Matlab Simulink. This pendulum can be used in the classroom to evaluate the controller design mentioned above. It is analysed if the use of the pendulum generates a deeper understanding of the learning contents. KW - Matlab KW - Engineering education KW - Online services KW - Software packages KW - Electronic learning KW - Control engineering Y1 - 2024 U6 - https://doi.org/10.1109/EDUCON60312.2024.10578937 SN - 2165-9559 SN - 2165-9567 (eISSN) N1 - 2024 IEEE Global Engineering Education Conference (EDUCON), 08-11 May 2024, Kos Island, Greece PB - IEEE CY - New York, NY ER - TY - GEN A1 - Frauenrath, Tobias A1 - Pfeiffer, Harald A1 - Hezel, Fabian A1 - Dieringer, Matthias A. A1 - Winter, Lukas A1 - Gräßl, Andreas A1 - Santoro, Davide A1 - Özerdem, Celal A1 - Renz, Wolfgang A1 - Greiser, Andreas A1 - Niendorf, Thoralf T1 - Lessons learned from cardiac MRI at 7.0 T: LV function assessment at 3.0 T using local multi-channel transceiver coil arrays T2 - 2012 ISMRM Annual Meeting Proceedings N2 - Cardiac MR (CMR) is of proven clinical value but also an area of vigorous ongoing research since image quality is not always exclusively defined by signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR). Recent developments of CMR at 7.0 T have been driven by pioneering explorations into novel multichannel transmit and receive coil array technology to tackle the challenges B1+-field inhomogeneities, to offset specific-absorption rate (SAR) constraints and to reduce banding artifacts in SSFP imaging. For this study, recognition of the benefits and performance of local surface Tx/Rx-array structures recently established at 7.0 T inspired migration to 3.0 T, where RF inhomogeneities and SAR limitations encountered in routine clinical CMR, though somewhat reduced versus the 7.0 T situation, remain significant. For all these reasons, this study was designed to build and examine the feasibility of a local four channel Tx/Rx cardiac coil array for anatomical and functional cardiac imaging at 3.0 T. For comparison, a homebuilt 4 channel Rx cardiac coil array exhibiting the same geometry as the Tx/Rx coil and a Rx surface coil array were used. Y1 - 2012 SN - 1545-4428 N1 - ISMRM 20th Annual Meeting & Exhibition, 5-11 May 2012, Melbourne, Australia ER - TY - RPRT A1 - Ritz, Thomas A1 - Siekmann, Kirsten A1 - Wallenborn, Ramona T1 - Anforderungen an die Gestaltung multimodaler Mobilitätsanwendungen : Potenziale für die IT-Branche bei der Organisation der verkehrsmittelübergreifenden Mobilität von morgen am Beispiel CarSharing und privater PKW ; Info-Broschüre N2 - Die Informationsbroschüre „Anforderungen an die Gestaltung multimodaler Mobilitätsanwendungen“ richtet sich an IT-Dienstleister. In dieser Broschüre werden mögliche Potenziale im Bereich des allgemeinen Mobilitätsmanagements aufgezeigt. Automobilhersteller vernetzten sich zunehmend mit Technologie-Unternehmen. Es geht nicht nur um die besondere Entwicklung von spezieller Elektronik- und Softwarelösungen für Navigations- und Entertainmentsysteme oder auch Fahrassistenz-Systemen in modernen PKW, sondern um einen übergreifenden Design- und Interaktionsansatz für miteinander vernetzte Geräte. Y1 - 2014 N1 - Mittelstand Digital PB - eBusiness-Lotse CY - Aachen ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - On an asymptotic relative efficiency concept based on expected volumes of confidence regions JF - Statistics - A Journal of Theoretical and Applied Statistic N2 - The paper deals with an asymptotic relative efficiency concept for confidence regions of multidimensional parameters that is based on the expected volumes of the confidence regions. Under standard conditions the asymptotic relative efficiencies of confidence regions are seen to be certain powers of the ratio of the limits of the expected volumes. These limits are explicitly derived for confidence regions associated with certain plugin estimators, likelihood ratio tests and Wald tests. Under regularity conditions, the asymptotic relative efficiency of each of these procedures with respect to each one of its competitors is equal to 1. The results are applied to multivariate normal distributions and multinomial distributions in a fairly general setting. KW - Volume of confidence regions KW - asymptotic relative efficiency KW - likelihood ratio test KW - multivariate normal distribution KW - multinomial distribution Y1 - 2019 U6 - https://doi.org/10.1080/02331888.2019.1683560 SN - 1029-4910 VL - 53 IS - 6 SP - 1396 EP - 1436 PB - Taylor & Francis CY - London ER - TY - CHAP A1 - Barnat, Miriam A1 - Bosse, Elke A1 - Mergner, Julia A1 - Jänsch, Vanessa T1 - Entwicklung studienrelevanter Kompetenzen im Zusammenspiel mit Studieneinstiegsangeboten T2 - KoBF-Auswertungsworkshop 31.05.-01.06.2017 Y1 - 2017 ER - TY - CHAP A1 - Hahne, E. A1 - Herrmann, Ulf A1 - Rheinländer, J. ED - Girot, Michel T1 - The Effect of Tilt on Flow Pattern of Water/Steam Flow Through Heated Tubes T2 - Experimental heat transfer, fluid mechanics and thermodynamics 1997 : proceedings of the 4th World Conference on Experimental Heat Transfer, Fluid Mechanics and Thermodynamics, Brussels, June 2 - 6, 1997. - Vol. 2 Y1 - 1997 SN - 88-467-0014-7 SP - 925 EP - 934 PB - Ed. ETS CY - Pisa ER - TY - CHAP A1 - Baier, Ralph A1 - Brauner, Philipp A1 - Brillowski, Florian A1 - Dammers, Hannah A1 - Liehner, Luca A1 - Pütz, Sebastian A1 - Schneider, Sebastian A1 - Schollemann, Alexander A1 - Steuer-Dankert, Linda A1 - Vervier, Luisa A1 - Gries, Thomas A1 - Leicht-Scholten, Carmen A1 - Mertens, Alexander A1 - Nagel, Saskia K. A1 - Schuh, Günther A1 - Ziefle, Martina A1 - Nitsch, Verena ED - Brecher, Christian ED - Schuh, Günther ED - van der Alst, Wil ED - Jarke, Matthias ED - Piller, Frank T. ED - Padberg, Melanie T1 - Human-centered work design for the internet of production T2 - Internet of production - fundamentals, applications and proceedings N2 - Like all preceding transformations of the manufacturing industry, the large-scale usage of production data will reshape the role of humans within the sociotechnical production ecosystem. To ensure that this transformation creates work systems in which employees are empowered, productive, healthy, and motivated, the transformation must be guided by principles of and research on human-centered work design. Specifically, measures must be taken at all levels of work design, ranging from (1) the work tasks to (2) the working conditions to (3) the organizational level and (4) the supra-organizational level. We present selected research across all four levels that showcase the opportunities and requirements that surface when striving for human-centered work design for the Internet of Production (IoP). (1) On the work task level, we illustrate the user-centered design of human-robot collaboration (HRC) and process planning in the composite industry as well as user-centered design factors for cognitive assistance systems. (2) On the working conditions level, we present a newly developed framework for the classification of HRC workplaces. (3) Moving to the organizational level, we show how corporate data can be used to facilitate best practice sharing in production networks, and we discuss the implications of the IoP for new leadership models. Finally, (4) on the supra-organizational level, we examine overarching ethical dimensions, investigating, e.g., how the new work contexts affect our understanding of responsibility and normative values such as autonomy and privacy. Overall, these interdisciplinary research perspectives highlight the importance and necessary scope of considering the human factor in the IoP. KW - Responsibility KW - Privacy KW - Digital leadership KW - Best practice sharing KW - Cognitive assistance system KW - Human-robot collaboration KW - Human-centered work design Y1 - 2023 SN - 978-3-030-98062-7 U6 - https://doi.org/10.1007/978-3-030-98062-7_19-1 N1 - Part of the book series: Interdisciplinary Excellence Accelerator Series (IDEAS) SP - 1 EP - 23 PB - Springer CY - Cham ER - TY - GEN A1 - Mayntz, Joscha A1 - Keimer, Jona A1 - Tegtmeyer, Philipp A1 - Dahmann, Peter A1 - Hille, Sebastian A1 - Stumpf, Eike A1 - Fisher, Alex A1 - Dorrington, Graham T1 - Aerodynamic Investigation on Efficient Inflight Transition of a Propeller from Propulsion to Regeneration Mode T2 - AIAA SCITECH 2022 Forum N2 - This paper discusses a new way of inflight power regeneration for electric or hybrid-electric driven general aviation aircraft with one powertrain for both configurations. Three different approaches for the shift from propulsion to regeneration mode are analyzed. Numerical cal-culation and wind tunnel results are compared and show the highest regeneration potential for the "Windmill" approach, where the propeller blades are flipped, and rotation is reversed. A combination of all regeneration approaches for a realistic flight mission is discussed. Y1 - 2021 U6 - https://doi.org/10.2514/6.2022-0546 N1 - AIAA SCITECH 2022 Forum, January 3-7, 2022, San Diego, CA & Virtual PB - AIAA CY - Reston, Va. ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - On an independence test approach to the goodness-of-fit problem JF - Journal of Multivariate Analysis N2 - Let X₁,…,Xₙ be independent and identically distributed random variables with distribution F. Assuming that there are measurable functions f:R²→R and g:R²→R characterizing a family F of distributions on the Borel sets of R in the way that the random variables f(X₁,X₂),g(X₁,X₂) are independent, if and only if F∈F, we propose to treat the testing problem H:F∈F,K:F∉F by applying a consistent nonparametric independence test to the bivariate sample variables (f(Xᵢ,Xⱼ),g(Xᵢ,Xⱼ)),1⩽i,j⩽n,i≠j. A parametric bootstrap procedure needed to get critical values is shown to work. The consistency of the test is discussed. The power performance of the procedure is compared with that of the classical tests of Kolmogorov–Smirnov and Cramér–von Mises in the special cases where F is the family of gamma distributions or the family of inverse Gaussian distributions. KW - Goodness-of-fit test KW - Independence test KW - Parametric bootstrap KW - Vapnik–Čhervonenkis class KW - Gamma distribution Y1 - 2015 U6 - https://doi.org/10.1016/j.jmva.2015.05.013 SN - 0047-259X VL - 2015 IS - 140 SP - 193 EP - 208 PB - Elsevier CY - Amsterdam ER - TY - GEN A1 - Frauenrath, Tobias A1 - Renz, Wolfgang A1 - Rieger, Jan A1 - Gömmel, Andreas A1 - Butenweg, Christoph A1 - Niendorf, Thoralf T1 - High Spatial Resolution 3D MRI of the Larynx Using a Dedicated TX/RX Phased Array Coil at 7.0T T2 - 2010 ISMRM-ESMRMB joint annual meeting N2 - MRI holds great potential for elucidating laryngeal and vocal fold anatomy together with the assessment of physiological processes associated in human phonation. However, MRI of human phonation remains very challenging due to the small size of the targeted structures, interfering signal from fat, air between the vocal folds and surrounding muscles and physiological motion. These anatomical/physiological constraints translate into stringent technical requirements in balancing, scan time, image contrast, immunity to physiological motion, temporal resolution and spatial resolution. Motivated by these challenges and limitations this study is aiming at translating the sensitivity gain at ultra-high magnetic fields for enhanced high spatial resolution 3D imaging of the larynx and vocal tract. To approach this goal a dedicated two channel TX/RX larynx coil is being proposed. Y1 - 2010 SN - 1545-4428 N1 - ISMRM-ESMRMB joint annual meeting, 1 - 7 May 2010, Stockholm, Sweden ER - TY - CHAP A1 - Steuer-Dankert, Linda T1 - A crazy little thing called sustainability T2 - 51st Annual Conference of the European Society for Engineering Education (SEFI) N2 - Achieving the 17 Sustainable Development Goals (SDGs) set by the United Nations (UN) in 2015 requires global collaboration between different stakeholders. Industry, and in particular engineers who shape industrial developments, have a special role to play as they are confronted with the responsibility to holistically reflect sustainability in industrial processes. This means that, in addition to the technical specifications, engineers must also question the effects of their own actions on an ecological, economic and social level in order to ensure sustainable action and contribute to the achievement of the SDGs. However, this requires competencies that enable engineers to apply all three pillars of sustainability to their own field of activity and to understand the global impact of industrial processes. In this context, it is relevant to understand how industry already reflects sustainability and to identify competences needed for sustainable development. KW - Transformative Competencies KW - Future Skills KW - Transdisciplinarity KW - Interdisciplinarity KW - Sustainability Y1 - 2023 U6 - https://doi.org/10.21427/9CQR-VC94 N1 - 51st Annual Conference of the European Society for Engineering Education, Technological University Dublin, 10th-14th September, 2023 ER - TY - JOUR A1 - Klinge, Uwe A1 - Otto, Jens A1 - Mühl, Thomas T1 - High Structural Stability of Textile Implants Prevents Pore Collapse and Preserves Effective Porosity at Strain JF - BioMed Research International Y1 - 2015 U6 - https://doi.org/10.1155/2015/953209 SN - 2314-6133 (Print) SN - 2314-6141 (Online) N1 - Article ID: 953209 VL - 2015 ER - TY - CHAP A1 - Moreno, Lia A1 - Dosev, D. A1 - Bratov, A. A1 - Dominguez, C. A1 - Schöning, Michael Josef A1 - Kloock, Joachim P. T1 - Effect of electrical properties of the surrounding medium on the response of an interdigitated electrode array with chalcogenide glass film T2 - XX Eurosensors : 20th anniversary ; Göteborg, Sweden, 17 - 20 September 2006 ; [proceedings]. - Vol. 1 Y1 - 2006 SN - 978-91-631-9280-7 N1 - Paper number: T1A-P22 SP - 384 EP - 385 CY - Göteborg ER - TY - PAT A1 - Rosenkranz, Josef T1 - Überwachungsvorrichtung für eine Auswuchtmaschine : Patentschrift Y1 - 2001 PB - Deutsches Patent- und Markenamt CY - München ER - TY - CHAP A1 - Kroll-Ludwigs, Kathrin T1 - Kommentierung zu §§ 1852 - 1857a T2 - Münchener Kommentar zum BGB Band 9, Familienrecht II Y1 - 2017 SN - 978-3-406-66548-6 PB - C.H.Beck CY - München ET - 7. Auflage ER - TY - CHAP A1 - Becker, Tim A1 - Bragard, Michael T1 - Low-Voltage DC Training Lab for Electric Drives - Optimizing the Balancing Act Between High Student Throughput and Individual Learning Speed T2 - 2024 IEEE Global Engineering Education Conference (EDUCON) N2 - After a brief introduction of conventional laboratory structures, this work focuses on an innovative and universal approach for a setup of a training laboratory for electric machines and drive systems. The novel approach employs a central 48 V DC bus, which forms the backbone of the structure. Several sets of DC machine, asynchronous machine and synchronous machine are connected to this bus. The advantages of the novel system structure are manifold, both from a didactic and a technical point of view: Student groups can work on their own performance level in a highly parallelized and at the same time individualized way. Additional training setups (similar or different) can easily be added. Only the total power dissipation has to be provided, i.e. the DC bus balances the power flow between the student groups. Comparative results of course evaluations of several cohorts of students are shown. KW - Synchronous machines KW - Power dissipation KW - Throughput KW - Low voltage KW - DC machines KW - Manifolds KW - Training Y1 - 2024 U6 - https://doi.org/10.1109/EDUCON60312.2024.10578902 SN - 2165-9559 SN - 2165-9567 (eISSN) N1 - 2024 IEEE Global Engineering Education Conference (EDUCON), 08-11 May 2024, Kos Island, Greece PB - IEEE CY - New York, NY ER - TY - CHAP A1 - Vladova, Gergana A1 - Ullrich, André A1 - Sultanow, Eldar A1 - Tobolla, Marinho A1 - Sebrak, Sebastian A1 - Czarnecki, Christian A1 - Brockmann, Carsten T1 - Visual analytics for knowledge management T2 - INFORMATIK 2023 - Designing Futures: Zukünfte gestalten N2 - The management of knowledge in organizations considers both established long-term processes and cooperation in agile project teams. Since knowledge can be both tacit and explicit, its transfer from the individual to the organizational knowledge base poses a challenge in organizations. This challenge increases when the fluctuation of knowledge carriers is exceptionally high. Especially in large projects in which external consultants are involved, there is a risk that critical, company-relevant knowledge generated in the project will leave the company with the external knowledge carrier and thus be lost. In this paper, we show the advantages of an early warning system for knowledge management to avoid this loss. In particular, the potential of visual analytics in the context of knowledge management systems is presented and discussed. We present a project for the development of a business-critical software system and discuss the first implementations and results. Y1 - 2023 SN - 978-3-88579-731-9 U6 - https://doi.org/10.18420/inf2023_187 SN - 1617-5468 N1 - INFORMATIK 2023, 26. - 29. September 2023, Berlin SP - 1851 EP - 1870 PB - GI - Gesellschaft für Informatik CY - Bonn ER - TY - CHAP A1 - Staat, Manfred A1 - Tran, Ngoc Trinh T1 - Strain based brittle failure criteria for rocks T2 - Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training N2 - When confining pressure is low or absent, extensional fractures are typical, with fractures occurring on unloaded planes in rock. These “paradox” fractures can be explained by a phenomenological extension strain failure criterion. In the past, a simple empirical criterion for fracture initiation in brittle rock has been developed. But this criterion makes unrealistic strength predictions in biaxial compression and tension. A new extension strain criterion overcomes this limitation by adding a weighted principal shear component. The weight is chosen, such that the enriched extension strain criterion represents the same failure surface as the Mohr–Coulomb (MC) criterion. Thus, the MC criterion has been derived as an extension strain criterion predicting failure modes, which are unexpected in the understanding of the failure of cohesive-frictional materials. In progressive damage of rock, the most likely fracture direction is orthogonal to the maximum extension strain. The enriched extension strain criterion is proposed as a threshold surface for crack initiation CI and crack damage CD and as a failure surface at peak P. Examples show that the enriched extension strain criterion predicts much lower volumes of damaged rock mass compared to the simple extension strain criterion. KW - Extension fracture KW - Extension strain criterion KW - Mohr–Coulomb criterion KW - Evolution of damage Y1 - 2023 SN - 978-604-357-084-7 N1 - 11th National Conference on Mechanics (NACOME 2022), December 2-3, 2022, VNU University of Engineering and Technology, Hanoi, Vietnam SP - 500 EP - 509 PB - Nha xuat ban Khoa hoc tu nhien va Cong nghe (Verlag Naturwissenschaft und Technik) CY - Hanoi ER - TY - PAT A1 - Troeder, Christoph A1 - Benner, Joachim A1 - Altherr, Marcel A1 - Schiessl, Helmut F. T1 - Topfspinnvorrichtung : [Offenlegungsschrift] T1 - Pot spinning device : [Patentschrift] N2 - "The invention relates to a pot spinning device (1) comprising a thread guide (9) which can be moved backwards and forwards and introduced into an opening (8) on the end side of the pot (7) so as to deposit a thread on the inside wall of a spinning pot. In order to improve upon pot spinning devices of this kind, the spinning pot is connected to an electric drive mechanism (10), mounted in magnetic bearings and provided with a gastight housing. Said housing encompasses the spinning pot (7), is open in the area where there is an opening in the end side of the pot and is provided with a seal (19) to seal off the intermediate area (17) between the housing and spinning pot. The housing is also connected to a supply of light-gas via a feed line (18), thereby enabling a light-gas atmosphere to be maintained in the intermediate area." Y1 - 1999 N1 - Außerdem veröffentlicht als: DE19815546(C2), CA2334866(A1), AU3704699(A) und AR019018(A1) PB - Deutsches Patent- und Markenamt ; Weltorganisation für Geistiges Eigentum CY - München ; Genf ER - TY - JOUR A1 - Frauenrath, Tobias A1 - Niendorf, Thoralf A1 - Kob, Malte T1 - Acoustic method for synchronization of Magnetic Resonance Imaging (MRI) JF - Acta Acustica N2 - Magnetic Resonance Imaging (MRI) of moving organs requires synchronization with physiological motion or flow, which dictate the viable window for data acquisition. To meet this challenge, this study proposes an acoustic gating device (ACG) that employs acquisition and processing of acoustic signals for synchronization while providing MRI compatibility, immunity to interferences with electro-magnetic and acoustic fields and suitability for MRI at high magnetic field strengths. The applicability and robustness of the acoustic gating approach is examined in a pilot study, where it substitutes conventional ECG-gating for cardiovascular MR. The merits and limitations of the ACG approach are discussed. Implications for MR imaging in the presence of physiological motion are considered including synchronization with other structure- or motion borne sounds. Y1 - 2008 U6 - https://doi.org/10.3813/AAA.918017 SN - 1861-9959 VL - 94 IS - 1 SP - 148 EP - 155 PB - Hirzel CY - Stuttgart ER - TY - JOUR A1 - Berndt, Heinz A1 - Zahn, Helmut T1 - Peptide, 99 : Monomere cyclische Cystinpeptidderivate, III ; Synthese der Schafinsulin-A-Kettensequenzen A2–21 und A1–21 als monomere cyclische Dicystinpeptidderivate JF - Justus Liebigs Annalen der Chemie N2 - Die Synthese der Sequenzen A2—21 (13) und A1—21 (15) der Schafinsulin-A-Kette als monomere cyclische Dicystinpeptidderivate wird beschrieben. Die intrachenaren Cystinbrücken A6—7 und A 11 —20 vermitteln die Löslichkeit dieser Derivate in Dimethylformamid und ermöglichen erstmalig die Reindarstellung vollgeschützter Insulin-A-Kettenderivate. Die während der Synthese eingesetzten Schutzgruppen lassen sich mittels Trifluoressigsäure und 2-Mercaptoäthanol quantitativ entfernen. Y1 - 1975 U6 - https://doi.org/10.1002/jlac.197519750908 SN - 1099-0690 VL - 1975 IS - 9 SP - 1601 EP - 1612 PB - Wiley-VCH CY - Weinheim ER - TY - CHAP A1 - Huth, Thomas A1 - Elsen, Olaf A1 - Hartwig, Christoph A1 - Esch, Thomas T1 - Innovative modular valve trains for 2015 - logistic benefits by EMVT T2 - IFAC Proceedings Volumes, Volume 39, Issue 3 N2 - In this paper the way to a 5-day-car with respect to a modular valve train systems for spark ignited combustion engines is shown. The necessary product diversity is shift from mechanical or physical components to software components. Therefore, significant improvements of logistic indicators are expected and shown. The working principle of a camless cylinder head with respect to an electromagnetical valve train (EMVT) is explained and it is demonstrated that shifting physical diversity to software is feasible. The future design of combustion engine systems including customisation can be supported by a set of assistance tools which is shown exemplary. Y1 - 2006 U6 - https://doi.org/10.3182/20060517-3-FR-2903.00172 N1 - Part of special issue "12th IFAC Symposium on Information Control Problems in Manufacturing" SP - 315 EP - 320 PB - Elsevier CY - Amsterdam ER -