TY - JOUR A1 - Cheenakula, Dheeraja A1 - Hoffstadt, Kevin A1 - Krafft, Simone A1 - Reinecke, Diana A1 - Klose, Holger A1 - Kuperjans, Isabel A1 - Grömping, Markus T1 - Anaerobic digestion of algal–bacterial biomass of an Algal Turf Scrubber system JF - Biomass Conversion and Biorefinery N2 - This study investigated the anaerobic digestion of an algal–bacterial biofilm grown in artificial wastewater in an Algal Turf Scrubber (ATS). The ATS system was located in a greenhouse (50°54′19ʺN, 6°24′55ʺE, Germany) and was exposed to seasonal conditions during the experiment period. The methane (CH4) potential of untreated algal–bacterial biofilm (UAB) and thermally pretreated biofilm (PAB) using different microbial inocula was determined by anaerobic batch fermentation. Methane productivity of UAB differed significantly between microbial inocula of digested wastepaper, a mixture of manure and maize silage, anaerobic sewage sludge, and percolated green waste. UAB using sewage sludge as inoculum showed the highest methane productivity. The share of methane in biogas was dependent on inoculum. Using PAB, a strong positive impact on methane productivity was identified for the digested wastepaper (116.4%) and a mixture of manure and maize silage (107.4%) inocula. By contrast, the methane yield was significantly reduced for the digested anaerobic sewage sludge (50.6%) and percolated green waste (43.5%) inocula. To further evaluate the potential of algal–bacterial biofilm for biogas production in wastewater treatment and biogas plants in a circular bioeconomy, scale-up calculations were conducted. It was found that a 0.116 km2 ATS would be required in an average municipal wastewater treatment plant which can be viewed as problematic in terms of space consumption. However, a substantial amount of energy surplus (4.7–12.5 MWh a−1) can be gained through the addition of algal–bacterial biomass to the anaerobic digester of a municipal wastewater treatment plant. Wastewater treatment and subsequent energy production through algae show dominancy over conventional technologies. KW - Biogas KW - Methane KW - Algal Turf Scrubber KW - Algal–bacterial bioflm KW - Circular bioeconomy Y1 - 2022 U6 - http://dx.doi.org/10.1007/s13399-022-03236-z SN - 2190-6823 N1 - Corresponding author: Dheeraja Cheenakula VL - 13 SP - 15 Seiten PB - Springer CY - Berlin ER - TY - JOUR A1 - Kuperjans, Isabel A1 - Starke, M. A1 - Esser, J. A1 - [u.a.], T1 - Analyse und Konzeption von Energieanlagen unter ökologischen, wirtschaftlichen und technischen Gesichtspunkten JF - WLB : Umwelttechnik für Industrie und Kommune Y1 - 2000 SN - 0341-2679 VL - 44 IS - 11/12 SP - 26 EP - 29 ER - TY - THES A1 - Borchert, Jörg T1 - Analyse von Determinanten der Großhandelspreise für Elektrizität anhand einer Systemstudie des deutschen Marktes Y1 - 2003 N1 - Berlin, Techn. Univ., Diss., 2003 ER - TY - CHAP A1 - Gedle, Yibekal A1 - Schmitz, Mark A1 - Gielen, Hans A1 - Schmitz, Pascal A1 - Herrmann, Ulf A1 - Teixeira Boura, Cristiano José A1 - Mahdi, Zahra A1 - Caminos, Ricardo Alexander Chico A1 - Dersch, Jürgen T1 - Analysis of an integrated CSP-PV hybrid power plant T2 - SolarPACES 2020 N2 - In the past, CSP and PV have been seen as competing technologies. Despite massive reductions in the electricity generation costs of CSP plants, PV power generation is - at least during sunshine hours - significantly cheaper. If electricity is required not only during the daytime, but around the clock, CSP with its inherent thermal energy storage gets an advantage in terms of LEC. There are a few examples of projects in which CSP plants and PV plants have been co-located, meaning that they feed into the same grid connection point and ideally optimize their operation strategy to yield an overall benefit. In the past eight years, TSK Flagsol has developed a plant concept, which merges both solar technologies into one highly Integrated CSP-PV-Hybrid (ICPH) power plant. Here, unlike in simply co-located concepts, as analyzed e.g. in [1] – [4], excess PV power that would have to be dumped is used in electric molten salt heaters to increase the storage temperature, improving storage and conversion efficiency. The authors demonstrate the electricity cost sensitivity to subsystem sizing for various market scenarios, and compare the resulting optimized ICPH plants with co-located hybrid plants. Independent of the three feed-in tariffs that have been assumed, the ICPH plant shows an electricity cost advantage of almost 20% while maintaining a high degree of flexibility in power dispatch as it is characteristic for CSP power plants. As all components of such an innovative concept are well proven, the system is ready for commercial market implementation. A first project is already contracted and in early engineering execution. KW - Hybrid energy system KW - Power plants KW - Electricity generation KW - Energy storage KW - Associated liquids Y1 - 2022 SN - 978-0-7354-4195-8 U6 - http://dx.doi.org/10.1063/5.0086236 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - 26th International Conference on Concentrating Solar Power and Chemical Energy Systems 28 September–2 October 2020 Freiburg, Germany IS - 2445 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - JOUR A1 - Maurer, Florian A1 - Rieke, Christian A1 - Schemm, Ralf A1 - Stollenwerk, Dominik T1 - Analysis of an urban grid with high photovoltaic and e-mobility penetration JF - Energies N2 - This study analyses the expected utilization of an urban distribution grid under high penetration of photovoltaic and e-mobility with charging infrastructure on a residential level. The grid utilization and the corresponding power flow are evaluated, while varying the control strategies and photovoltaic installed capacity in different scenarios. Four scenarios are used to analyze the impact of e-mobility. The individual mobility demand is modelled based on the largest German studies on mobility “Mobilität in Deutschland”, which is carried out every 5 years. To estimate the ramp-up of photovoltaic generation, a potential analysis of the roof surfaces in the supply area is carried out via an evaluation of an open solar potential study. The photovoltaic feed-in time series is derived individually for each installed system in a resolution of 15 min. The residential consumption is estimated using historical smart meter data, which are collected in London between 2012 and 2014. For a realistic charging demand, each residential household decides daily on the state of charge if their vehicle requires to be charged. The resulting charging time series depends on the underlying behavior scenario. Market prices and mobility demand are therefore used as scenario input parameters for a utility function based on the current state of charge to model individual behavior. The aggregated electricity demand is the starting point of the power flow calculation. The evaluation is carried out for an urban region with approximately 3100 residents. The analysis shows that increased penetration of photovoltaics combined with a flexible and adaptive charging strategy can maximize PV usage and reduce the need for congestion-related intervention by the grid operator by reducing the amount of kWh charged from the grid by 30% which reduces the average price of a charged kWh by 35% to 14 ct/kWh from 21.8 ct/kWh without PV optimization. The resulting grid congestions are managed by implementing an intelligent price or control signal. The analysis took place using data from a real German grid with 10 subgrids. The entire software can be adapted for the analysis of different distribution grids and is publicly available as an open-source software library on GitHub. KW - distribution grid simulation KW - smart-charging KW - e-mobility Y1 - 2023 U6 - http://dx.doi.org/10.3390/en16083380 SN - 1996-1073 N1 - This article belongs to the Special Issue "Advanced Solutions for the Efficient Integration of Electric Vehicles in Electricity Grids" N1 - Corresponding author: Florian Maurer VL - 16 IS - 8 PB - MDPI CY - Basel ER - TY - CHAP A1 - Rosin, J. A1 - Mykoniou, K. A1 - Butenweg, Christoph T1 - Analysis Of Base Isolated Liquid Storage Tanks With 3D Fsi-Analysis As Well As Simplified Approaches T2 - 16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017 N2 - Tanks are preferably designed, for cost-saving reasons, as circular, cylindrical, thin-walled shells. In case of seismic excitation, these constructions are highly vulnerable to stability failures. An earthquake-resistant design of rigidly supported tanks for high seismic loading demands, however, uneconomic wall thicknesses. A cost-effective alternative can be provided by base isolation systems. In this paper, a simplified seismic design procedure for base isolated tanks is introduced, by appropriately modifying the standard mechanical model for flexible, rigidly supported tanks. The non-linear behavior of conventional base isolation systems becomes an integral part of a proposed simplified process, which enables the assessment of the reduced hydrodynamic forces acting on the tank walls and the corresponding stress distribution. The impulsive and convective actions of the liquid are taken into account. The validity of this approach is evaluated by employing a non-linear fluid-structure interaction algorithm of finite element method. Special focus is placed on the boundary conditions imposed from the base isolation and the resulting hydrodynamic pressures. Both horizontal and vertical component of ground motion are considered in order to study the principal effects of the base isolation on the pressure distribution of the tank walls. The induced rocking effects associated with elastomeric bearings are discussed. The results manifest that base isolated tanks can be designed for seismic loads by means of the proposed procedure with sufficient accuracy, allowing to dispense with numerically expensive techniques. KW - liquid storage tank KW - seismic isolation KW - elastomeric bearing KW - friction pendulum bearing KW - simplified approach Y1 - 2017 N1 - Paper No 2246 SP - 1 EP - 14 PB - Chilean Association on Seismology and Earthquake Engineering (ACHISINA) ER - TY - JOUR A1 - Butenweg, Christoph A1 - Rosin, Julia A1 - Holler, Stefan T1 - Analysis of cylindrical granular material silos under seismic excitation JF - Buildings N2 - Silos generally work as storage structures between supply and demand for various goods, and their structural safety has long been of interest to the civil engineering profession. This is especially true for dynamically loaded silos, e.g., in case of seismic excitation. Particularly thin-walled cylindrical silos are highly vulnerable to seismic induced pressures, which can cause critical buckling phenomena of the silo shell. The analysis of silos can be carried out in two different ways. In the first, the seismic loading is modeled through statically equivalent loads acting on the shell. Alternatively, a time history analysis might be carried out, in which nonlinear phenomena due to the filling as well as the interaction between the shell and the granular material are taken into account. The paper presents a comparison of these approaches. The model used for the nonlinear time history analysis considers the granular material by means of the intergranular strain approach for hypoplasticity theory. The interaction effects between the granular material and the shell is represented by contact elements. Additionally, soil–structure interaction effects are taken into account. KW - granular silo KW - earthquake engineering KW - hypoplasticity KW - nonlinear transient analyses Y1 - 2017 U6 - http://dx.doi.org/10.3390/buildings7030061 SN - 2075-5309 VL - 7 IS - 3 SP - 1 EP - 12 PB - MDPI CY - Basel ER - TY - CHAP A1 - Breitbach, Gerd A1 - Alexopoulos, Spiros A1 - May, Martin A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Analysis of volumetric solar radiation absorbers made of wire meshes T2 - AIP Conference Proceedings Y1 - 2019 U6 - http://dx.doi.org/10.1063/1.5117521 SN - 0094243X VL - 2126 SP - 030009-1 EP - 030009-6 ER - TY - JOUR A1 - Barsov, S. A1 - Bechstedt, U. A1 - Hardt, Arno T1 - ANKE, a new facility for medium energy hadron physics at COSY-Jülich / S. Barsov [u.a.] JF - Nuclear instruments and methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. Vol. 462, iss. 3 Y1 - 2001 SN - 0167-5087 (Print) ; 0168-9002 (E-journal) SP - 364 EP - 381 ER - TY - JOUR A1 - Kern, Alexander A1 - Zischank, Wolfgang A1 - Beierl, Ottmar T1 - Anmerkungen zur Berechnung des Trennungsabstands nach DIN EN 62305-3 (VDE 0185-305-3): 2006-10 / Zischank, Wolfgang ; Beierl, Ottmar ; Kern, Alexander JF - 7. VDE-ABB-Blitzschutztagung : Vorträge der VDE-ABB-Fachtagung vom 15. bis 16. November 2007 in Neu-Ulm / Veranst.: Ausschuss für Blitzschutz und Blitzforschung (ABB) im VDE, Verband der Elektrotechnik, Elektronik, Informationstechnik e.V. Wiss. Tagungsltg.: K. Stimper Y1 - 2007 SN - 978-3-8007-3062-9 N1 - VDE-Fachbericht ; 64 ; Blitzschutztagung <7, 2007, Neu-Ulm> SP - 1 EP - 8 PB - VDE-Verl. CY - Berlin ER - TY - JOUR A1 - Förster, Arnold A1 - Darmo, J. A1 - Dubecký, F. A1 - Kordos, P. T1 - Annealing characteristics of native defects in low-temperature-grown MBE GaAs / J. Darmo ; F. Dubecky ; P. Kordos ; A. Förster JF - Semiconducting and insulating materials 1996 : proceedings of the 9th Conference on Semiconducting and Insulating Materials (SIMC '9), April 29 - May 3, 1996, Toulouse, France / [IEEE] Y1 - 1996 SN - 0-7803-3095-1 N1 - 2. ISBN: 0-7803-3179-6 ; Conference on Semiconducting and Insulating Materials <9, 1996, Toulouse> ; Institute of Electrical and Electronics Engineers ; IEEE Cat. No.96CH35881 SP - 67 EP - ff. CY - Piscataway, NJ [u.a.] ER - TY - JOUR A1 - Förster, Arnold A1 - Darmo, J. A1 - Dubecky, F. A1 - Kordos, P. T1 - Annealing effect on concentration of EL6-like deep-level state in low-temperature-grown molecular beam epitaxial GaAs. Darmo, J.; Dubecky, F.; Kordos, P.; Förster, A. JF - Applied Physics Letters. 72 (1998), H. 5 Y1 - 1998 SN - 1077-3118 SP - 590 EP - 592 ER - TY - BOOK A1 - Breitbach, Gerd A1 - Altes, Jürgen T1 - Anwendung der Finite Elemente Methode auf Probleme mit Wärmestrahlungsaustausch Y1 - 1985 N1 - (Berichte der Kernforschungsanlage Jülich / Kernforschungsanlage ; 2013) PB - Zentralbibliothek der Kernforschungsanlage CY - Jülich ER - TY - JOUR A1 - Breitbach, Gerd A1 - Altes, J. A1 - Szimmat, J. T1 - Anwendung der Finite-Element-Methode bei der Berechnung des Wärmetransports durch Strahlung / J. Altes ; G. Breitbach ; J. Szimmat JF - International FEM-Congress : Baden-Baden, Federal Republic of Germany, 17./18. November 1986 Y1 - 1989 N1 - International FEM Congress <15, 1986, Baden-Baden> SP - 127 EP - 148 PB - IKO Software Service GmbH CY - Stuttgart ER - TY - BOOK A1 - Förster, Arnold T1 - Anwendung der hochauflösenden Elektronenenergieverlustspektroskopie zum Studium von Halbleiterschichtsystemen. - (Berichte der Kernforschungsanlage Jülich / Kernforschungsanlage ; 2247) Y1 - 1988 N1 - Zugl.: Aachen, Techn. Hochsch., Diss., 1988 PB - Zentralbibliothek der Kernforschungsanlage CY - Jülich ER - TY - JOUR A1 - Schwarzer, Klemens T1 - Anwendung solarer Hochtemperaturwärme am Beispiel eines Solarkochers JF - Wege in die Solargesellschaft 4 : Dokumentation zur Vortragsreihe an der Fachhochschule Darmstadt in Zusammenarbeit mit dem IKU-Institut für kommunale Wirtschaft und Umweltplanung im Sommersemester 1993 / [Hrsg.: Projektgruppe Solarenergie an der Fachhochschule Darmstadt ; IKU-Inst. für Kommunale Wirtschaft u. Umweltplanung. Red.: Helmut C. Büscher] Y1 - 1993 N1 - Ringvorlesung Wege in die Solargesellschaft <4, 1993, Darmstadt> SP - 13 EP - 24 PB - FHD CY - Darmstadt ER - TY - BOOK A1 - Dören, Horst-Peter T1 - Anwendung von AlN- bzw. AlN-Al2O3-Mischungen als Festelektrolyt in Eisenschmelzen bei 1640° C Y1 - 1977 N1 - Dissertation, RWTH Aachen CY - Aachen ER - TY - CHAP A1 - Kruska, Martin A1 - Kuperjans, Isabel T1 - Análisis Thermodinámicos : [Capítulo 3.3] T2 - Uso racional de energía : eficiencia energética y energías renovables. - (Manual para consultores y expertos) Y1 - 1999 SP - 3.3-1 EP - 3.3-15 PB - Ministerio de Energía y Minas CY - Lima ER - TY - JOUR A1 - Helsper, Christoph A1 - Nießner, R. T1 - Application of a Multistep Condensation Nuclei Counter as a Detector for Particle Surface Composition / Nießner, R. ; Helsper, C. JF - Journal of Aerosol Science. 16 (1985), H. 3 Y1 - 1985 SN - 0021-8502 SP - 201 EP - 209 ER - TY - JOUR A1 - Helsper, Christoph A1 - Nießner, R. A1 - Rönicke, G. T1 - Application of a Multistep Condensation Nuclei Counter as a Detector for Particle Surface Composition / Nießner, R.; Helsper, C.; Rönicke, G. JF - Aerosols : science, technology, and industr. applications of airborne particles ; proceedings of the 1. Internat. Aerosol Conference held Sept. 17-21, 1984, Minneapolis, Minn., U.S.A / ed.: Benjamin Y. H. Liu Y1 - 1984 SN - 0444009477 N1 - International Aerosol Conference ; (1, 1984, Minneapolis, Minn.) SP - 63 EP - 66 PB - Elsevier CY - New York [u.a.] ER - TY - JOUR A1 - Pieper, Martin A1 - Klein, Peter T1 - Application of simple, periodic homogenization techniques to non-linear heat conduction problems in non-periodic, porous media JF - Heat mass transfer N2 - Often, detailed simulations of heat conduction in complicated, porous media have large runtimes. Then homogenization is a powerful tool to speed up the calculations by preserving accurate solutions at the same time. Unfortunately real structures are generally non-periodic, which requires unpractical, complicated homogenization techniques. We demonstrate in this paper, that the application of simple, periodic techniques to realistic media, that are just close to periodic, gives accurate, approximative solutions. In order to obtain effective parameters for the homogenized heat equation, we have to solve a so called “cell problem”. In contrast to periodic structures it is not trivial to determine a suitable unit cell, which represents a non-periodic media. To overcome this problem, we give a rule of thumb on how to choose a good cell. Finally we demonstrate the efficiency of our method for virtually generated foams as well as real foams and compare these results to periodic structures. Y1 - 2012 U6 - http://dx.doi.org/10.1007/s00231-011-0879-4 SN - 0947-7411 VL - 48 IS - 2 SP - 291 EP - 300 PB - Springer CY - Berlin ER - TY - CHAP A1 - Darveniza, M. A1 - Flisowski, Z. A1 - Kern, Alexander A1 - Landers, E.-U. A1 - LoPiparo, G. A1 - Mazzetti, C. A1 - Rousseau, A. A1 - Sherlock, J. T1 - Application problems of the probabilistic approach to the assessment of risk for structures and services N2 - The paper deals with the development of the probabilistic approach to the assessment of risk due to lightning. Sources of damage, types of damage and types of loss are defined and, accordingly, the procedure for risk analysis and the way of assessment of different risk components is proposed. The way to evaluate the influence of different protection measures (lightning protection system; shielding of structure, cables and equipment; routing of internal wiring; surge protective device) in reducing such probabilities is considered. The paper has been prepared within the framework of the activity of IEC TC81-WG9/CLC TC81-WG4 directed to prepare the draft IEC 62305-2 Risk Management, in cooperation with the Secretary of IEC/CLC TC81. KW - Blitzschutz KW - Risikoabwägung KW - Lightning protection system KW - risk assessment KW - protection measures Y1 - 2002 ER - TY - CHAP A1 - Hellmanns, Mark A1 - Fischer, F. A1 - Dilger, Klaus T1 - Applikation und Einsatz von faserverstärkten Klebstoffen im Bauwesen T2 - Tagungsband / 13. Kolloquium Gemeinsame Forschung in der Klebtechnik : 26. und 27. Februar 2013, Frankfurt am Main Y1 - 2013 SP - 61 EP - 62 PB - DECHEMA CY - Frankfurt a.M. ER - TY - RPRT A1 - Dilger, Klaus A1 - Fischer, Fabian A1 - Hellmanns, Mark A1 - Werner, Frank A1 - Wittor, Björn T1 - Applikation und Einsatz von faserverstärkten Klebstoffen im Bauwesen (FibrAdh) : Schlussbericht : gefördertes Vorhaben 16.956 B / DVS-Nr. 08.072 Y1 - 2013 ER - TY - CHAP A1 - Hellmanns, Mark A1 - Fischer, F. A1 - Dilger, K. A1 - Wittor, B. A1 - Hildebrand, J. A1 - Werner, F. T1 - Applikation und Einsatz von faserverstärkten Klebstoffen im Bauwesen abgeschlossenes IGF-Projekt Nr. 16956 B (DVS 08.072, Laufzeit 01.02.2011 - 31.01.2013) T2 - Tagungsband / 14. Kolloquium Gemeinsame Forschung in der Klebtechnik : 18. und 19. Februar 2014, DECHEMA-Haus, Frankfurt am Main Y1 - 2014 SP - 26 EP - 27 ER - TY - JOUR A1 - Förster, Arnold A1 - Resch, U. A1 - Essera, N. A1 - Raptis, Y. S. T1 - Arsenic passivation of MBE grown GaAs(100): structural and electronic properties of the decapped surfaces / U. Resch ; N. Essera ; Y. S. Raptis ... A. Förster ... JF - Surface Science. 269-270 (1992) Y1 - 1992 SN - 0039-6028 N1 - ISSN der E-Ausg.: 0039-6028 SP - 797 EP - 803 ER - TY - JOUR A1 - Förster, Arnold A1 - Schäfer, B.-J. A1 - Londschien, M. T1 - Arsenic passivation of MOMBE grown GaAs surfaces / B. -J. Schäfer ; A. Förster ; M. Londschien ... JF - Surface Science. 204 (1988), H. 3 Y1 - 1988 SN - 0039-6028 N1 - ISSN der E-Ausg.: 0039-6028 SP - 485 EP - 490 ER - TY - CHAP A1 - Zischank, Wolfgang J. A1 - Kern, Alexander A1 - Frentzel, Ralf A1 - Heidler, Fridolin A1 - Seevers, M. T1 - Assessment of the lightning transient coupling to control cables interconnecting structures in large industrial facilities and power plants N2 - Large industrial facilities and power plants often require a huge number fo information and control cables between the differnet structures. These I&C-cables can be routed in reinforced concrete cable ducts or in isolated buried cable runs. KTA 2206 is the German lightning protection standard for nuclear power plants. During the last several years considerable effort has been made to revise this standard. Despite the well established principles and design guidelines for the construction of the lightning protection system, this standard puts special emphasis on the coupling of transient overvoltages to I&C-cables. KW - Blitzschutz KW - Elektromagnetische Kopplung KW - Überspannung KW - Kraftwerke KW - Industrieanlagen KW - Lightning KW - current distribution KW - electromagnetic coupling KW - overvoltages Y1 - 2000 ER - TY - JOUR A1 - Gerling, Ulrich A1 - Lück, Reinhard A1 - Predel, Bruno T1 - Assoziation in flüssigen Antimon-Zink-Legierungen und die Berücksichtigung der Größenverhältnisse der Teilchen in der Schmelze JF - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 77, H. 2 Y1 - 1986 SN - 0044-3093 ; 0179-4841 SP - 80 EP - 86 ER - TY - JOUR A1 - Gerling, Ulrich A1 - Lück, Reinhard A1 - Predel, Bruno T1 - Assoziation in flüssigen Germanium-Zink-Legierungen JF - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 77, H. 6 Y1 - 1986 SN - 0044-3093 ; 0179-4841 SP - 489 EP - 496 ER - TY - JOUR A1 - Gerling, Ulrich A1 - Predel, Bruno T1 - Assoziation in flüssigen Gold-Zink-Legierungen und die Zuverlässigkeit der Modellparameter JF - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 75, H. 8 Y1 - 1984 SN - 0044-3093 ; 0179-4841 SP - 592 EP - 598 ER - TY - JOUR A1 - Lück, Reinhard A1 - Gerling, Ulrich A1 - Predel, Bruno T1 - Assoziation in Mehrstoffsystemen JF - Zeitschrift für Metallkunde : international journal of materials research and advanced techniques. Bd. 77, H. 10 Y1 - 1986 SN - 0044-3093 ; 0179-4841 SP - 667 EP - 672 ER - TY - JOUR A1 - Förster, Arnold A1 - Rosenauer, A. A1 - Oberst, W. A1 - Gerthsen, D. T1 - Atomic scale analysis of the indium distribution in InGaAs/GaAs (001) heterostructures: segregation, lateral indium redistribution and the effect of growth interruptions. Rosenauer, A. ; Oberst, W. ; Gerthsen, D. ; Förster, A. JF - Thin Solid Films. 357 (1999) Y1 - 1999 SN - 0040-6090 SP - 18 EP - 21 ER - TY - JOUR A1 - Förster, Arnold A1 - Rosenauer, A. A1 - Remmele, T. T1 - Atomic scale strain measurements by the digital analysis of transmission electron microscopic lattice images / A. Rosenauer ; T. Remmele ; D. Gerthsen ... A. Förster JF - Optik : international journal for light and electron optics. 105 (1997), H. 3 Y1 - 1997 SN - 0030-4026 SP - 99 EP - 107 ER - TY - BOOK A1 - Hardt, Arno A1 - Müller, Gerhard A1 - Berg, G. P. A1 - Kelleter, H.-J. T1 - Aufbau eines Plastikszintillationszählers für den Magnetspektrographen "BIG KARL" am Jülicher Zyklotron "JULIC". Müller, Gerhard; Berg , G. P.; Hardt, A.; Kelleter, H.-J.; Martin, S.-A.; Meissburger, J. Y1 - 1980 N1 - Spezielle Berichte der Kernforschungsanlage Jülich ; Nr. 0084 PB - Kernforschungsanlage Jülich CY - Jülich ER - TY - BOOK A1 - Rateike, Franz-Matthias A1 - Werner, Linus A1 - Wunderer, Bernd T1 - Aufbau und Entwicklung frequenzveränderlicher Hochdruck-Gaslaser für photochemische Anwendungen / Matthias Rateike ; Linus Werner ; Bernd Wunderer. Y1 - 1980 N1 - Forschungsbericht / Bundesministerium fuer Forschung und Technologie : T ; 80,107 PB - Fachinformationszentrum Energie, Physik, Mathematik CY - Eggenstein-Leopoldshafen ER - TY - JOUR A1 - Thielemann, Frank A1 - Bock, Jürgen T1 - Aufbau und Management deutsch-russischer Joint-ventures. Bock Jürgen; Thielemann, Frank JF - Mit Innovation vom Plan zum Markt Y1 - 1993 SP - 111 EP - 135 CY - Bochum ER - TY - CHAP A1 - Borchert, Jörg ED - Zenke, Ines T1 - Aufbau von Handelseinheiten T2 - Energiehandel in Europa Y1 - 2012 SN - 978-3-406-63237-2 SP - 467 EP - 479 PB - Beck CY - München ET - 3. Aufl. ER - TY - CHAP A1 - Dören, Horst-Peter A1 - Wernicke, K. T1 - Auftragen von verschleißfesten stranggegossenen Hartlegierungen auf Kobaltbasis durch das WIG- und Gasschweißen T2 - Schweißen und Schneiden '83 = Welding and Cutting '83. Vorträge der Großen Schweißtechnischen Tagung in Aachen vom 28. bis 30. September 1983. Veranst.: Deutscher Verband für Schweißtechnik (DVS). DVS-Berichte. 83 Y1 - 1983 SN - 3-87155-388-3 SP - 109 EP - 113 PB - Dt. Verl. für Schweißtechnik CY - Düsseldorf ER - TY - JOUR A1 - Buck, H. A1 - Schwarzer, Klemens A1 - Meliß, Michael A1 - Faber, Christian T1 - Aus- und Weiterbildung am Solar-Institut Jülich JF - Energiewirtschaftliche Tagesfragen. 44 (1994), H. 9 Y1 - 1994 SN - 0720-6240 SP - 65 EP - 68 ER - TY - JOUR A1 - Buck, H. A1 - Faber, Christian A1 - Meliß, Michael A1 - Schwarzer, Klemens T1 - Aus- und Weiterbildung am Solar-Institut Jülich JF - Energie für die Zukunft : 28. Juni bis 1. Juli 1994 ; [Tagungsbericht 2] / 9. Internationales Sonnenforum '94. [Hrsg. Deutsche Gesellschaft für Sonnenenergie e.V. - DGS. Red. A. Hohmann ; H. H. Hohmann]. - (Internationales Sonnenforum ; 9,2) Y1 - 1995 N1 - Internationales Sonnenforum <9, 1994, Stuttgart> ; Deutsche Gesellschaft für Sonnenenergie SP - 1779 EP - 1785 PB - DGS-Sonnenenergie CY - München ER - TY - CHAP A1 - Stangel-Meseke, Martina A1 - Hahn, Pia A1 - Steuer-Dankert, Linda T1 - Ausblick: Der individualitätsbezogene Diversity Management-Ansatz als Antwort auf Individualisierung T2 - Diversity Management und Individualisierung N2 - Der Megatrend Individualisierung fordert von Unternehmen, ihre Strategien und Prozessabläufe bei zunehmender Globalisierung grundlegend zu überdenken. Während Strategien und Prozessabläufe im Unternehmen Standards unterliegen, entwickelt sich unsere Gesellschaft immer stärker zu einem individuumszentrierten System, in dem es gilt, Werte und Lebensstile der Individuen zu berücksichtigen und derart wertzuschätzen, dass Mitarbeitende motiviert und mit hoher Bindung an das Unternehmen die anstehenden Leistungen für das Unternehmen erbringen. Im Konzept DiM sind Standardisierung und Individualisierung keine gegensätzlichen Aspekte, da bei DiM neben der Betrachtung des betriebswirtschaftlichen Nutzens dieses Konzepts für Unternehmen die Wertschätzung des Individuums als genuines Merkmal betont wird. Y1 - 2015 SN - 978-3-658-07485-2 SP - 23 EP - 24 PB - Springer Gabler CY - Wiesbaden ER - TY - JOUR A1 - Brüssermann, Klaus T1 - Ausbreitungsrechnungen aus ingenieurtechnischer Sicht JF - Meeting of Umweltbundesamt Working Group for Diffusion Calculation, Berlin (Germany, F.R.), 10 May 1984 Y1 - 1984 N1 - Heft 21/85 SP - 1 EP - 11 ER - TY - CHAP A1 - Butenweg, Christoph A1 - Kubalski, Thomas A1 - Marinkovic, Marko A1 - Pfetzing, Thomas A1 - Ismail, Mohammed A1 - Fehling, Ekkehard T1 - Ausfachungen aus Ziegelmauerwerk T2 - Mauerwerk-Kalender 2016: Baustoffe, Sanierung, Eurocode-Praxis Y1 - 2016 SN - 978-3-433-03131-5 PB - Ernst & Sohn CY - Berlin ER - TY - JOUR A1 - Marinkovic, Marko A1 - Butenweg, Christoph T1 - Ausfachungen aus Ziegelmauerwerk in Stahlbetonrahmentragwerken unter Erdbebenbeanspruchung JF - Mauerwerk N2 - Stahlbetonrahmentragwerke mit Ausfachungen aus Mauerwerk weisen nach Erdbeben häufig schwere Schäden auf. Gründe hierfür sind die Beanspruchungen der Ausfachungswände durch die aufgezwungenen Rahmenverformungen in Wandebene und die gleichzeitig auftretenden Trägheitskräfte senkrecht zur Wandebene in Kombination mit der konstruktiven Ausführung des Ausfachungsmauerwerks. Die Ausfachung wird in der Regel knirsch gegen die Rahmenstützen gemauert, wobei der Verschluss der oberen Fuge mit Mörtel oder Montageschaum erfolgt. Dadurch kommt es im Erdbebenfall zu lokalen Interaktionen zwischen Ausfachung und Rahmen, die in der Folge zu einem Versagen einzelner Ausfachungswände oder zu einem sukzessiven Versagen des Gesamtgebäudes führen können. Die beobachteten Schäden waren die Motivation dafür, in dem europäischen Forschungsprojekt INSYSME für Stahlbetonrahmentragwerke mit Ausfachungen aus hochwärmedämmenden Ziegelmauerwerk innovative Lösungen zur Verbesserung des seismischen Verhaltens zu entwickeln. Der vorliegende Beitrag stellt die im Rahmen des Projekts von den deutschen Projektpartnern (Universität Kassel, SDA-engineering GmbH) entwickelten Lösungen vor und vergleicht deren seismisches Verhalten mit der traditionellen Ausführung der Ausfachungswände. Grundlage für den Vergleich sind statisch-zyklische Wandversuche und Simulationen auf Wandebene. Aus den Ergebnissen werden Empfehlungen für die erdbebensichere Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk abgeleitet. Y1 - 2020 U6 - http://dx.doi.org/10.1002/dama.202000011 SN - 1437-1022 VL - 24 IS - 4 SP - 194 EP - 205 PB - Wiley CY - Weinheim ER - TY - CHAP A1 - Kubalski, T. A1 - Butenweg, Christoph T1 - Ausfachungsmauerwerk unter kombinierter seismischer Beanspruchung T2 - Erdbeben und bestehende Bauten : 14. D-A-C-H Tagung 20.08. - 21.08.2015, ETH Zürich. (Dokumentation / SIA ; D 0255) Y1 - 2015 SN - 978-3-03732-060-0 SP - 117 EP - 122 PB - SGEB CY - Zürich ER - TY - CHAP A1 - Butenweg, Christoph A1 - Roeser, W. T1 - Auslegung von Bauwerken gegen Erdbeben - Rechenbeispiele T2 - Stahlbetonbau aktuell 2016 : Praxishandbuch / herausgegeben von: Prof. Dr.-Ing. Josef Hegger, Prof. Dr.-Ing. habil. Peter Mark Y1 - 2016 SN - 978-3-410-25202-3 (Print) ; 978-3-410-25203-0 (E-Book) PB - Beuth Verlag GmbH CY - Berlin ; Wien ; Zürich ER - TY - JOUR A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Voss, Michael T1 - Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 1) T1 - Design of reinforced concrete enclosures infilled with clay block masonry (Part 1) JF - Ziegelindustrie international : ZI = Brick and tile industry international N2 - Im Rahmen des europäischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragfähigkeit durch aufwendige und kostspielige zusätzliche Bewehrungseinlagen zu erhöhen. Erste Ergebnisse des Systems IMES für Belastungen in und senkrecht zu der Wandebene werden vorgestellt. N2 - Within the scope of the joint European project INSYSME, the German partners developed two systems - IMES and INODIS - for improving the seismic behaviour of masonry infilled reinforced concrete frames. The purpose of both systems is to decouple frame and infill instead of working to improve their load-bearing capacity by means of elaborate, expensive, supplementary reinforcing elements. Initial findings for the IMES system with regard to the loads acting in-plane and perpendicular to the wall plane (out-of-plane) are presented. Y1 - 2018 SN - 0341-0552 IS - 4 SP - 30 EP - 39 PB - Bauverlag BV GmbH CY - Gütersloh ER - TY - JOUR A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Voss, Michael T1 - Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 2) T1 - Design of reinforced concrete enclosures infilled with clay block masonry (Part 2) JF - Ziegelindustrie international : ZI = Brick and tile industry international N2 - Im Rahmen des europäischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragfähigkeit durch aufwendige und kostspielige zusätzliche Bewehrungseinlagen zu erhöhen. Erste Ergebnisse des Systems IMES für Belastungen in und senkrecht zu der Wandebene werden vorgestellt. N2 - Within the scope of the joint European project INSYSME, the German partners developed two systems - IMES and INODIS - for improving the seismic behaviour of masonry infilled reinforced concrete frames. The purpose of both systems is to decouple frame and infill instead of working to improve their load-bearing capacity by means of elaborate, expensive, supplementary reinforcing elements. Initial findings for the IMES system with regard to the loads acting in-plane and perpendicular to the wall plane (out-of-plane) are presented. Y1 - 2018 SN - 0341-0552 IS - 6 SP - 24 EP - 43 PB - Bauverlag BV GmbH CY - Gütersloh ER - TY - CHAP A1 - Dümmler, Andreas A1 - Oetringer, Kerstin A1 - Göttsche, Joachim T1 - Auslegungstool zur energieeffizienten Kühlung von Gebäuden T2 - DKV-Tagung 2020, AA IV Y1 - 2020 N1 - Deutsche Kälte- und Klimatagung 2020 online SP - 1 EP - 12 ER -