TY - JOUR A1 - Hanrath, Wilhelm A1 - Plesken, Wilhelm T1 - Group rings and irreducible representations of space groups / by W. Hanrath and W. Plesken JF - Journal für die reine und angewandte Mathematik. 362 (1985) Y1 - 1985 SN - 0075-4102 SP - 130 EP - 140 ER - TY - JOUR A1 - Gebhardt, Andreas T1 - Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping" N2 - Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering – Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision KW - Rapid prototyping KW - Rapid Technologie KW - Rapid Prototyping Y1 - 2006 ER - TY - JOUR A1 - Ulmer, Jessica A1 - Braun, Sebastian A1 - Cheng, Chi-Tsun A1 - Dowey, Steve A1 - Wollert, Jörg T1 - Gamification of virtual reality assembly training: Effects of a combined point and level system on motivation and training results JF - International Journal of Human-Computer Studies N2 - Virtual Reality (VR) offers novel possibilities for remote training regardless of the availability of the actual equipment, the presence of specialists, and the training locations. Research shows that training environments that adapt to users' preferences and performance can promote more effective learning. However, the observed results can hardly be traced back to specific adaptive measures but the whole new training approach. This study analyzes the effects of a combined point and leveling VR-based gamification system on assembly training targeting specific training outcomes and users' motivations. The Gamified-VR-Group with 26 subjects received the gamified training, and the Non-Gamified-VR-Group with 27 subjects received the alternative without gamified elements. Both groups conducted their VR training at least three times before assembling the actual structure. The study found that a level system that gradually increases the difficulty and error probability in VR can significantly lower real-world error rates, self-corrections, and support usages. According to our study, a high error occurrence at the highest training level reduced the Gamified-VR-Group's feeling of competence compared to the Non-Gamified-VR-Group, but at the same time also led to lower error probabilities in real-life. It is concluded that a level system with a variable task difficulty should be combined with carefully balanced positive and negative feedback messages. This way, better learning results, and an improved self-evaluation can be achieved while not causing significant impacts on the participants' feeling of competence. KW - Gamification KW - Virtual reality KW - Assembly KW - User study KW - Level system Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.ijhcs.2022.102854 SN - 1071-5819 VL - 165 IS - Art. No. 102854 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Dues, M. A1 - Gebhardt, Andreas A1 - Kallweit, Stephan A1 - Scheffler, T. A1 - Siekmann, H. A1 - Uchiyama, T. T1 - Flow Visualization in a Cavitating Flow JF - Proceedings of the German-Japanese Symposium on Multi-Phase Flow : Karlsruhe, Germany, August 23 - 25, 1994 / comp. by U. Müller ... Y1 - 1994 N1 - German Japanese Symposium on Multi-Phase Flow <1994, Karlsruhe> ; Kernforschungszentrum Karlsruhe ; 5389 SP - 391 EP - 402 PB - Kernforschungszentrum Karlsruhe CY - Karlsruhe ER - TY - JOUR A1 - Kilic, S. A. A1 - Raatschen, Hans-Jürgen A1 - Körfgen, B. A1 - Apaydin, N. M. A1 - Astaneh-Asl, A. T1 - FE Model of the Fatih Sultan Mehmet Suspension Bridge Using Thin Shell Finite Elements JF - Arabian Journal for Science and Engineering N2 - This paper presents the results of an eigenvalue analysis of the Fatih Sultan Mehmet Bridge. A high-resolution finite element model was created directly from the available design documents. All physical properties of the structural components were included in detail, so no calibration to the measured data was necessary. The deck and towers were modeled with shell elements. A nonlinear static analysis was performed before the eigenvalue calculation. The calculated natural frequencies and corresponding mode shapes showed good agreement with the available measured ambient vibration data. The calculation of the effective modal mass showed that nine modes had single contributions higher than 5 % of the total mass. They were in a frequency range up to 1.2 Hz. The comparison of the results for the torsional modes especially demonstrated the advantage of using thin shell finite elements over the beam modeling approach. KW - Suspension bridge KW - 3D nonlinear finite element model KW - Thin shell finite elements KW - Natural frequency KW - Effective modal mass Y1 - 2017 U6 - http://dx.doi.org/10.1007/s13369-016-2316-y SN - 2191-4281 VL - 42 IS - 3 SP - 1103 EP - 1116 PB - Springer Nature ER - TY - JOUR A1 - Kallweit, Stephan A1 - Uchiyama, R. A1 - Siekmann, H. T1 - Fault Diagnostic Method for Pump Running Conditions Based on Process Modeling and Neural Network / Uchiyama, R. ; Kallweit, S. ; Siekmann, H. JF - International Journal of Rotating Machinery. 4 (1998), H. 1 Y1 - 1998 SN - 1542-3034 SP - 49 EP - 59 ER - TY - JOUR A1 - Mautner, Karin A1 - Forster, Ralf A1 - Kornhuber, Ralf A1 - Sander, Oliver T1 - Fast and Reliable Pricing of American Options with Local Volatility / Forster, Ralf ; Kornhuber, Ralf ; Mautner, Karin ; Sander, Oliver JF - Domain Decomposition Methods in Science and Engineering XVII Y1 - 2008 SN - 978-3-540-75198-4 N1 - Lecture Notes in Computational Sciece and Engineering ; 60 SP - 383 EP - 390 ER - TY - JOUR A1 - Wang, Mao A1 - Anik, Sabri A1 - Frohberg, Martin G. T1 - Experiments on the electrochemical determination of the sulphur activities in the system copper-silver at 1200°C JF - Zeitschrift für Metallkunde Y1 - 1988 SN - 0044-3093 VL - 79 IS - 5 SP - 336 EP - 339 ER - TY - JOUR A1 - Anik, Sabri A1 - Frohberg, Martin G. A1 - Kapoor, Madan Lal T1 - Experiments and theoretical considerations on the solution of oxygen in binary metal alloys JF - Berichte der Bunsengesellschaft für physikalische Chemie Y1 - 1983 SN - 0005-9021 SN - 0940-483X VL - 87 IS - 12 SP - 1201 EP - 1204 ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas A1 - Thümmler, Stefan A1 - Thurn, Laura T1 - Experimental investigation on selective laser melting of glass JF - Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014 Y1 - 2014 U6 - http://dx.doi.org/10.1016/j.phpro.2014.08.118 SN - 1875-3892 (E-Journal); 1875-3884 (Print) VL - 56 (2014) SP - 357 EP - 364 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Fateri, Miranda A1 - Hötter, Jan-Steffen A1 - Gebhardt, Andreas T1 - Experimental and Theoretical Investigation of Buckling Deformation of Fabricated Objects by Selective Laser Melting JF - Physics Procedia N2 - Although Selective Laser Melting (SLM) process is an innovative manufacturing method, there are challenges such as inferior mechanical properties of fabricated objects. Regarding this, buckling deformation which is caused by thermal stress is one of the undesired mechanical properties which must be alleviated. As buckling deformation is more observable in hard to process materials, silver is selected to be studied theoretically and experimentally for this paper. Different scanning strategies are utilized and a Finite Element Method (FEM) is applied to calculate the temperature gradient in order to determine its effect on the buckling deformation of the objects from experiments. Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.phpro.2012.10.062 SN - 1875-3892 N1 - Part of special issue "Laser Assisted Net shape Engineering 7 (LANE 2012)" VL - 39 SP - 464 EP - 470 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Enning, Manfred A1 - Baier, M. T1 - Energetic and operational use of FlexCargoRail freight wagons in the single wagon load traffic / Baier, M. ; Enning, M. JF - Towards zero emission : EVS 24, the 24th International Battery, Hybrid and Fuel Cell Electric Vehicle Symposium & Exhibition, Stavanger, Norway, May 13 - 16, 2009 ; symposium proceedings / organised by AVERE ... Robert Stüssi [Hrsg.] Y1 - 2009 N1 - European Association of Electric Road Vehicles ; EVS ; (24 : ; 2009.05.13-16 : ; Stavanger) CY - Stavanger ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Ehrfeld, W. A1 - Hagemann, B. A1 - Lehr, H. T1 - Electromagnetic permanent magnet micromotor with integrated micro gear box. Kämper, K.-P.; Ehrfeld, W.; Hagemann, B.; Lehr, H.; Michel, F.; Schirling, A.; Thürigen, C.; Wittig, T. JF - Actuator 96 : Conference Proceedings ; 5th International Conference on New Actuators ; 26- 28 June, Bremen, Germany / Ed.: Hubert Borgmann. Publ. by: AXON Technology Consult GmbH Y1 - 1996 N1 - International Conference on New Actuators <5, 1996, Bremen> SP - 429 CY - Bremen ER - TY - JOUR A1 - Heinrichs, Horst A1 - Weck, H. T1 - Efficient finite-element structural analysis by interactive graphic mesh generation JF - CIRP Annals. 30 (1981), H. 1 Y1 - 1981 SP - 279 EP - 284 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Schmitt, W. A1 - Güntherodt, G. T1 - Effect of adsorbates on the spin-polarized photoemission of itinerant ferromagnets. Schmitt, W.; Kämper, K.-P.; Güntherodt, G. JF - Physical Review B. 36 (1987), H. 7 Y1 - 1987 SN - 1095-3795 SP - 3763 EP - 3768 ER - TY - JOUR A1 - Kämper, Klaus-Peter T1 - Education and Training in MST. Kämper, K.-P.; Picard, A.; Brill, M.; Cassel, D.; Jentsch, A.; Merten, S.; Rollwa, M. JF - Mst-News (2003) Y1 - 2003 SN - 0948-3128 SP - 35 ER - TY - JOUR A1 - Dilthey, Ulrich A1 - Brandenburg, Annette A1 - Schleser, Markus T1 - Dispensing and application of unfilled adhesives in the micro range JF - Welding and cutting. 3 (2004), H. 4 Y1 - 2004 SN - 1612-3433 SP - 250 EP - 254 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Lehr, H. A1 - Ehrfeld, W. A1 - Hagemann, B. T1 - Development of micro and millimotors. Lehr, H.; Ehrfeld, W.; Hagemann, B.; Kämper, K.-P.; Michel, F.; Schulz, C.; Thürigen C. JF - Minimally Invasive Therapy and Allied Technologies. 6 (1997) Y1 - 1997 SN - 1364-5706 ER - TY - JOUR A1 - Kämper, Klaus-Peter T1 - Development of low-cost injection moulded micropumps. Entwicklung von kostengünstigen, mittels Spritzguß hergestellten Mikropumpen / Döpper, J. (u.a.) JF - Actuator 96 : Conference Proceedings ; 5th International Conference on New Actuators ; 26- 28 June, Bremen, Germany / Ed.: Hubert Borgmann. Publ. by: AXON Technology Consult GmbH Y1 - 1996 N1 - Konferenz-Einzelbericht: ACTUATOR, Internat. Conf. on New Actuators, 5 SP - 37 EP - 40 CY - Bremen ER - TY - JOUR A1 - Starke, Günther A1 - Drews, P. T1 - Development approaches for advanced control in automated arc welding Y1 - 1985 N1 - Konferenz-Einzelbericht: Automation and robotisation in welding and allied processes. International conference on automation and robotisation in welding and allied processes, Strasbourg, FR, 02.09.1985-03.09.1985 SP - 115 EP - 124 ER - TY - JOUR A1 - Enning, Manfred A1 - Jenayeh, I. A1 - Müller, C. A1 - Rake, Heinrich T1 - Development and realization of a manipulator for automatic decoupling of freight cars in marshalling yards / Jenayeh, I. ; Müller, C. ; Enning, Manfred ; Rake, Heinrich ; Peter, J. Y1 - 1997 N1 - World Congress on Railway Research, Florenz, 16.-19.11.1997, 1997 ER - TY - JOUR A1 - Franko, Josef A1 - Du, Shengzhi A1 - Kallweit, Stephan A1 - Duelberg, Enno Sebastian A1 - Engemann, Heiko T1 - Design of a Multi-Robot System for Wind Turbine Maintenance JF - Energies N2 - The maintenance of wind turbines is of growing importance considering the transition to renewable energy. This paper presents a multi-robot-approach for automated wind turbine maintenance including a novel climbing robot. Currently, wind turbine maintenance remains a manual task, which is monotonous, dangerous, and also physically demanding due to the large scale of wind turbines. Technical climbers are required to work at significant heights, even in bad weather conditions. Furthermore, a skilled labor force with sufficient knowledge in repairing fiber composite material is rare. Autonomous mobile systems enable the digitization of the maintenance process. They can be designed for weather-independent operations. This work contributes to the development and experimental validation of a maintenance system consisting of multiple robotic platforms for a variety of tasks, such as wind turbine tower and rotor blade service. In this work, multicopters with vision and LiDAR sensors for global inspection are used to guide slower climbing robots. Light-weight magnetic climbers with surface contact were used to analyze structure parts with non-destructive inspection methods and to locally repair smaller defects. Localization was enabled by adapting odometry for conical-shaped surfaces considering additional navigation sensors. Magnets were suitable for steel towers to clamp onto the surface. A friction-based climbing ring robot (SMART— Scanning, Monitoring, Analyzing, Repair and Transportation) completed the set-up for higher payload. The maintenance period could be extended by using weather-proofed maintenance robots. The multi-robot-system was running the Robot Operating System (ROS). Additionally, first steps towards machine learning would enable maintenance staff to use pattern classification for fault diagnosis in order to operate safely from the ground in the future. Y1 - 2020 U6 - http://dx.doi.org/10.3390/en13102552 SN - 1996-1073 VL - 13 IS - 10 SP - Article 2552 PB - MDPI CY - Basel ER - TY - JOUR A1 - Grundmann, Reinhard T1 - Design Criteria for Aeroacoustic Wind Tunnels Y1 - 1992 N1 - Konferenzeinzelbericht : DGLR-workshop : Joint meeting of the Specialists Groups Test Facilities/Aeroacoustics - Flight Noise . Deutsche Gesellschaft für Luft- und Raumfahrt. Test Facilities Specialist Group ; Deutsche Gesellschaft für Luft- und Raumfahr ER - TY - JOUR A1 - Abbas, Karim A1 - Balc, Nicolae A1 - Bremen, Sebastian A1 - Skupin, Marco T1 - Crystallization and aging behavior of polyetheretherketone PEEK within rapid tooling and rubber molding JF - Journal of Manufacturing and Materials Processing N2 - In times of short product life cycles, additive manufacturing and rapid tooling are important methods to make tool development and manufacturing more efficient. High-performance polymers are the key to mold production for prototypes and small series. However, the high temperatures during vulcanization injection molding cause thermal aging and can impair service life. The extent to which the thermal stress over the entire process chain stresses the material and whether it leads to irreversible material aging is evaluated. To this end, a mold made of PEEK is fabricated using fused filament fabrication and examined for its potential application. The mold is heated to 200 ◦C, filled with rubber, and cured. A differential scanning calorimetry analysis of each process step illustrates the crystallization behavior and first indicates the material resistance. It shows distinct cold crystallization regions at a build chamber temperature of 90 ◦C. At an ambient temperature above Tg, crystallization of 30% is achieved, and cold crystallization no longer occurs. Additional tensile tests show a decrease in tensile strength after ten days of thermal aging. The steady decrease in recrystallization temperature indicates degradation of the additives. However, the tensile tests reveal steady embrittlement of the material due to increasing crosslinking. KW - additive manufacturing KW - fused filament fabrication KW - crystallization KW - polyetheretherketone KW - rapid tooling Y1 - 2022 U6 - http://dx.doi.org/10.3390/jmmp6050093 SN - 2504-4494 N1 - The article belongs to the Special Issue Advances in Injection Molding: Process, Materials and Applications VL - 6 IS - 5 SP - 1 EP - 12 PB - MDPI CY - Basel ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Schmitt, W. A1 - Güntherodt, G. A1 - Gambino, R. J. T1 - CrO2—A New Half-Metallic Ferromagnet? Kämper, K.-P.; Schmitt, W.; Güntherodt, G.; Gambino, R. J., Ruf, R. JF - Physical Review Letters. 59 (1987), H. 24 Y1 - 1987 SN - 1079-7114 SP - 2788 EP - 2791 ER - TY - JOUR A1 - Enning, Manfred A1 - Stützle, Thorsten A1 - Viereck, Uwe A1 - Stribersky, Anton T1 - Creepage control for use in wheelslide protection systems / Stützle, Thorsten ; Viereck, Uwe ; Stribersky, Anton ; Rulka, Wolfgang ; Enning, Manfred ; Abel, Dirk JF - Control in transportation systems : proceedings of the 11th IFAC symposium on control in transportation systems (CTS 2006), August 29-31, 2006, Delft, the Netherlands / International Federation of Automatic Control Y1 - 2006 SN - 0742-5953 ER - TY - JOUR A1 - Starke, Günther A1 - Kuhne, A.H. A1 - Frassek, B. T1 - Components for the automated GMAW process. Bestandteile des automatischen Metall-Schutzgas-Schweissverfahrens JF - Welding Journal. 63 (1984), H. 1 Y1 - 1984 SN - 0043-2296 SP - 31 EP - 34 ER - TY - JOUR A1 - Wollbrink, Moritz A1 - Maslo, Semir A1 - Zimmer, Daniel A1 - Abbas, Karim A1 - Arntz, Kristian A1 - Bergs, Thomas T1 - Clamping and substrate plate system for continuous additive build-up and post-processing of metal parts JF - Procedia CIRP N2 - The manufacturing share of laser powder bed fusion (L-PBF) increases in industrial application, but still many process steps are manually operated. Additionally, it is not possible to achieve tight dimensional tolerances or low surfaces roughness. Hence, a process chain has to be set up to combine additive manufacturing (AM) with further machining technologies. To achieve a continuous workpiece flow as basis for further industrialization of L-PBF, the paper presents a novel substrate system and its application on L-PBF machines and post-processing. The substrate system consists of a zero-point clamping system and a matrix-like interface of contact pins to be substantially connected to the workpiece within the L-PBF process. Y1 - 2020 U6 - http://dx.doi.org/10.1016/j.procir.2020.04.015 SN - 2212-8271 VL - 93 SP - 108 EP - 113 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Mukherjee, Krishnendu A1 - Ramazani, Ali A1 - Yang, Li A1 - Prahl, Ulrich A1 - Bleck, Wolfgang A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Abdurakhmanov, Aydemir T1 - Characterization of gas metal arc welded hot rolled DP600 steel JF - Steel research international Y1 - 2011 SN - 1869-344X (E-Book); 1611-3683 (Print) VL - Vol. 82 IS - Iss. 12 SP - 1408 EP - 1416 PB - Wiley CY - Weinheim ER - TY - JOUR A1 - Mukherjee, Krishnendu A1 - Prahl, Ulrich A1 - Bleck, Wolfgang A1 - Reisgen, Uwe A1 - Schleser, Markus A1 - Abdurakhmanov, Aydemir T1 - Characterization and modelling techniques for gas metal arc welding of DP 600 sheet steels JF - Materialwissenschaft und Werkstofftechnik N2 - The objectives of the present work are to characterize the Gas Metal Arc Welding process of DP 600 sheet steel and to summarize the modelling techniques. The time-temperature evolution during the welding cycle was measured experimentally and modelled with the softwaretool SimWeld. To model the phase transformations during the welding cycle dilatometer tests were done to quantify the parameters for phase field modelling by MICRESS®. The important input parameters are interface mobility, nucleation density, etc. A contribution was made to include austenite to bainite transformation in MICRESS®. This is useful to predict the microstructure in the fast cooling segments. The phase transformation model is capable to predict the microstructure along the heating and cooling cycles of welding. Tensile tests have shown the evidence of failure at the heat affected zone, which has the ferrite-tempered martensite microstructure. Y1 - 2010 U6 - http://dx.doi.org/10.1002/mawe.201000692 SN - 1521-4052 VL - 41 IS - 11 SP - 972 EP - 983 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Hanrath, Wilhelm T1 - Character tables of some factor groups of space groups JF - Perfect groups / Derek F. Holt and W. Plesken Y1 - 1989 SN - 0-19-853559-7 SP - 357 EP - 359 PB - Clarendon Press CY - Oxford ER - TY - JOUR A1 - Haag, S. A1 - Zontar, D. A1 - Schleupen, Josef A1 - Müller, T. A1 - Brecher, C. T1 - Chain of refined perception in self-optimizing assembly of micro-optical systems JF - Journal of sensors and sensor systems N2 - Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements – especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base. Y1 - 2014 U6 - http://dx.doi.org/10.5194/jsss-3-87-2014 SN - 2194-878X VL - 3 IS - 1 SP - 87 EP - 95 PB - Copernicus Publ. CY - Göttingen ER - TY - JOUR A1 - Pfaff, Raphael T1 - Braking distance prediction for vehicle consist in low-speed on-sight operation: a Monte Carlo approach JF - Railway Engineering Science N2 - The first and last mile of a railway journey, in both freight and transit applications, constitutes a high effort and is either non-productive (e.g. in the case of depot operations) or highly inefficient (e.g. in industrial railways). These parts are typically managed on-sight, i.e. with no signalling and train protection systems ensuring the freedom of movement. This is possible due to the rather short braking distances of individual vehicles and shunting consists. The present article analyses the braking behaviour of such shunting units. For this purpose, a dedicated model is developed. It is calibrated on published results of brake tests and validated against a high-definition model for low-speed applications. Based on this model, multiple simulations are executed to obtain a Monte Carlo simulation of the resulting braking distances. Based on the distribution properties and established safety levels, the risk of exceeding certain braking distances is evaluated and maximum braking distances are derived. Together with certain parameters of the system, these can serve in the design and safety assessment of driver assistance systems and automation of these processes. KW - Freight rail KW - Shunting KW - Braking curves KW - Brake set-up KW - Driver assistance system Y1 - 2023 U6 - http://dx.doi.org/10.1007/s40534-023-00303-7 SN - 2662-4753 (eISSN) SN - 2662-4745 (Print) VL - 31 IS - 2 SP - 135 EP - 144 PB - SpringerOpen ER - TY - JOUR A1 - Feldmann, Markus A1 - Pak, Daniel A1 - Geßler, Achim A1 - Dilthey, Ulrich A1 - Schleser, Markus T1 - Bonded connections for textile reinforced concrete structures JF - Cailiao-gongcheng = Journal of materials engineering Y1 - 2006 SN - 1001-4381 IS - Special iss. SP - 123 EP - 127 ER - TY - JOUR A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas A1 - Abbas, Karim T1 - Basic Research on Lattice Structures Focused on the Tensile Strength JF - Applied Mechanics and Materials Y1 - 2015 U6 - http://dx.doi.org/10.4028/www.scientific.net/AMM.808.193 SN - 1662-7482 N1 - MTeM ; October 14-16, 2015, Cluj-Napoca, Romania VL - Vol. 808 SP - 193 EP - 198 PB - Trans Tech Publications CY - Bäch ER - TY - JOUR A1 - Enning, Manfred A1 - Mann, S. A1 - Bollig, A. A1 - Kaierle, S. T1 - Autonomous Production Cell for Laser Beam Welding / Mann S. ; Bollig, A. ; Kaierle, S. ; Abel, D. ; Poprawe, R. Y1 - 2003 SN - 0912035757 N1 - ICALEO 2003, Florida ; Laser Materials Processing Conference ; (2003, Jacksonville, Fla.) ; ICALEO ; (22, 2003, Jacksonville, Fla.) PB - LIA CY - Orlando, Fla ER - TY - JOUR A1 - Enning, Manfred A1 - Bernhard, S. A1 - Rake, H. T1 - Automation of a laboratory plant for direct casting of thin steel strips / Bernhard, S. ; Enning, M. ; Rake, H. JF - Control Engineering Practice. 2 (1994), H. 6 Y1 - 1994 SN - 0967-0661 SP - 961 EP - 967 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Lehr, H. A1 - Abel, S. A1 - Ehrfeld, W. T1 - Assembly of Electromagnetic Milliactuators with LIGA Components. Lehr, H.; Abel, S.; Ehrfeld, W.; Hagemann, B.; Kämper, K.-P.; Michel, F.; Thürigen, C. JF - Proceedings 2nd Japan-France Congress on Mechatronics, Takamatsu (Kagawa, Japan) 1.-3. November 1994, 31 (1994) Y1 - 1995 N1 - 2nd Japan-France Congress on mechatronics (1994 Nov : Takamatsu, Japan) SP - 31 EP - 31 PB - Fuji Technology Press ER - TY - JOUR A1 - Schleser, Markus A1 - Walk-Lauffer, Bernd A1 - Raupach, Michael A1 - Dilthey, Ulrich T1 - Application of polymers for textile-reinforced concrete JF - Journal of materials in civil engineering : properties, applications, durability Y1 - 2006 SN - 0899-1561 VL - 18 IS - 5 SP - 670 EP - 676 ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Döpper, J. A1 - Ehrfeld, W. A1 - Hagemann, B. T1 - An investigation of computer modelling for micro-injection moulding. Hill, S.D.J.; Kämper, K.-P.; Dasbach, U.; Döpper, J.; Ehrfeld, W.; Kaupert, M. JF - Simulation and design of microsystems and microstructures : [... contains the papers presented at the First International Conference on the Simulation and Design of Microsystems and Microstructures, MicroSIM '95, which was held in Southampton, UK, in September 1995] / [organised by: Wessex Institute of Technology, UK]. Ed.: R. A. Adey Y1 - 1995 SN - 1-85312-390-0 SP - 275 PB - Computational Mechanics Publ. CY - Southampton [u.a.] ER - TY - JOUR A1 - Abbas, Karim A1 - Hedwig, Lukas A1 - Balc, Nicolae A1 - Bremen, Sebastian T1 - Advanced FFF of PEEK: Infill strategies and material characteristics for rapid tooling JF - Polymers N2 - Traditional vulcanization mold manufacturing is complex, costly, and under pressure due to shorter product lifecycles and diverse variations. Additive manufacturing using Fused Filament Fabrication and high-performance polymers like PEEK offer a promising future in this industry. This study assesses the compressive strength of various infill structures (honeycomb, grid, triangle, cubic, and gyroid) when considering two distinct build directions (Z, XY) to enhance PEEK’s economic and resource efficiency in rapid tooling. A comparison with PETG samples shows the behavior of the infill strategies. Additionally, a proof of concept illustrates the application of a PEEK mold in vulcanization. A peak compressive strength of 135.6 MPa was attained in specimens that were 100% solid and subjected to thermal post-treatment. This corresponds to a 20% strength improvement in the Z direction. In terms of time and mechanical properties, the anisotropic grid and isotropic cubic infill have emerged for use in rapid tooling. Furthermore, the study highlights that reducing the layer thickness from 0.15 mm to 0.1 mm can result in a 15% strength increase. The study unveils the successful utilization of a room-temperature FFF-printed PEEK mold in vulcanization injection molding. The parameters and infill strategies identified in this research enable the resource-efficient FFF printing of PEEK without compromising its strength properties. Using PEEK in rapid tooling allows a cost reduction of up to 70% in tool production. KW - polyetheretherketone (PEEK) KW - rapid tooling KW - infill strategy KW - compression behavior KW - additive manufacturing KW - fused filament fabrication Y1 - 2023 U6 - http://dx.doi.org/10.3390/polym15214293 N1 - This article belongs to the Special Issue "Polymer Materials and Design Processes for Additively Manufactured Products" VL - 2023 IS - 15 PB - MDPI CY - Basel ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Picard, A. A1 - Schütze, A. A1 - Wallach, D. T1 - Adopting the Foundry Concept of Semiconductor Fabrication on Educational Schemes and the Virtual Technology Lab (VTL). Picard, A.; Kämper, K.-P.; Schütze, A.; Wallach, D.; Walter, T. JF - Mst-News (2006) Y1 - 2006 SN - 0948-3128 SP - 15, 16 EP - u. 35 ER - TY - JOUR A1 - Gebhardt, Andreas A1 - Schmidt, Frank-Michael A1 - Hötter, Jan-Steffen A1 - Sokalla, Wolfgang A1 - Sokalla, Patrick T1 - Additive Manufacturing by selective laser melting the realizer desktop machine and its application for the dental industry JF - Physics Procedia Y1 - 2010 SN - 1875-3892 N1 - Laser Assisted Net Shape Engineering 6, Proceedings of the LANE 2010, Part 2 VL - 5 IS - 2 SP - 543 EP - 549 ER - TY - JOUR A1 - Fateri, Miranda A1 - Gebhardt, Andreas T1 - Additive manufactured mechanical disentanglement lock JF - RTejournal - Forum für Rapid Technologie Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:0009-2-42147 SN - 1614-0923 VL - 12 PB - Fachhochschule Aachen CY - Aachen ER - TY - JOUR A1 - Kämper, Klaus-Peter A1 - Döpper, J. A1 - Ehrfeld, W. A1 - Oberbeck, S. T1 - A self-filling low-cost membrane micropump JF - Proceedings : an investigation of micro structures, sensors, actuators, machines and systems / sponsored by the IEEE Robotics and Automation Society in cooperation with the ASME Dynamic Systems and Control Division Y1 - 1998 SN - 078034412X N1 - International Workshop on Micro-Electro-Mechanical Systems <11, 1998, Heidelberg> SP - 432 EP - 437 PB - IEEE Service Center CY - Piscataway, NJ ER - TY - JOUR A1 - Engemann, Heiko A1 - Cönen, Patrick A1 - Dawar, Harshal A1 - Du, Shengzhi A1 - Kallweit, Stephan T1 - A robot-assisted large-scale inspection of wind turbine blades in manufacturing using an autonomous mobile manipulator JF - Applied Sciences N2 - Wind energy represents the dominant share of renewable energies. The rotor blades of a wind turbine are typically made from composite material, which withstands high forces during rotation. The huge dimensions of the rotor blades complicate the inspection processes in manufacturing. The automation of inspection processes has a great potential to increase the overall productivity and to create a consistent reliable database for each individual rotor blade. The focus of this paper is set on the process of rotor blade inspection automation by utilizing an autonomous mobile manipulator. The main innovations include a novel path planning strategy for zone-based navigation, which enables an intuitive right-hand or left-hand driving behavior in a shared human–robot workspace. In addition, we introduce a new method for surface orthogonal motion planning in connection with large-scale structures. An overall execution strategy controls the navigation and manipulation processes of the long-running inspection task. The implemented concepts are evaluated in simulation and applied in a real-use case including the tip of a rotor blade form. KW - mobile manipulation KW - large-scale inspection KW - wind turbine production KW - autonomous navigation KW - surface-orthogonal path planning Y1 - 2021 U6 - http://dx.doi.org/10.3390/app11199271 SN - 2076-3417 N1 - Belongs to the Special Issue "Advances in Industrial Robotics and Intelligent Systems" VL - 11 IS - 19 SP - 1 EP - 22 PB - MDPI CY - Basel ER - TY - JOUR A1 - Pfaff, Raphael A1 - Enning, Manfred A1 - Sutter, Stefan T1 - A risk‑based approach to automatic brake tests for rail freight service: incident analysis and realisation concept JF - SN Applied Sciences N2 - This study reviews the practice of brake tests in freight railways, which is time consuming and not suitable to detect certain failure types. Public incident reports are analysed to derive a reasonable brake test hardware and communication architecture, which aims to provide automatic brake tests at lower cost than current solutions. The proposed solutions relies exclusively on brake pipe and brake cylinder pressure sensors, a brake release position switch as well as radio communication via standard protocols. The approach is embedded in the Wagon 4.0 concept, which is a holistic approach to a smart freight wagon. The reduction of manual processes yields a strong incentive due to high savings in manual labour and increased productivity. KW - Freight rail KW - Brake test KW - Incident analysis KW - Train composition KW - Brake set-up Y1 - 2022 U6 - http://dx.doi.org/10.1007/s42452-022-05007-x SN - 2523-3971 N1 - Corresponding author: Raphael Pfaff VL - 4 IS - 4 SP - 1 EP - 14 PB - Springer CY - Cham ER - TY - JOUR A1 - Enning, Manfred A1 - Hücker, Jan A1 - Jenayeh, Imad A1 - Rake, Heinrich T1 - A Parametric Identification Scheme for a Self-tuning Industrial Compact Controller - INTERKAMA 1999 / Hucker, Jan ; Jenayeh, Imad ; Enning, Manfred ; Rake, Heinrich Y1 - 1999 N1 - ISA TP99UN139 ; Proceedings ISA-Tech Conference, Düsseldorf 1999 ER - TY - JOUR A1 - Scheidweiler, Robert A1 - Triesch, Eberhard T1 - A note on the duality between matchings and vertex covers in balanced hypergraphs JF - Journal of Combinatorial Optimization N2 - We present a new Min-Max theorem for an optimization problem closely connected to matchings and vertex covers in balanced hypergraphs. The result generalizes Kőnig’s Theorem (Berge and Las Vergnas in Ann N Y Acad Sci 175:32–40, 1970; Fulkerson et al. in Math Progr Study 1:120–132, 1974) and Hall’s Theorem (Conforti et al. in Combinatorica 16:325–329, 1996) for balanced hypergraphs. KW - Hall’s Theorem KW - Koenig’s Theorem KW - Duality KW - Balanced hypergraph KW - Hypergraph KW - Vertex cover KW - Matching Y1 - 2016 U6 - http://dx.doi.org/10.1007/s10878-015-9887-5 SN - 1573-2886 N1 - Lehrstuhl II für Mathematik RWTH Aachen VL - 32 IS - 2 SP - 639 EP - 644 PB - Springer CY - Berlin ER - TY - JOUR A1 - Enning, Manfred A1 - Jenayeh, I. A1 - Müller, C. A1 - Kositza, N. T1 - A New Approach for Automating Shunting Processes in Marshalling Yards / Jenayeh, I.; Müller, C. ; Kositza, N. ; Enning, M. ; Rake, H. JF - Computational Engineering in Systems Applications : 2nd IMACS International Multiconference CESA'98; [abstracts; Nabeul-Hammamet, Tunisia, April 1 - 4, 1998] / ed. by Pierre Borne Y1 - 1998 SP - 338 EP - 343 PB - UCIS CY - Villeneuve d'Ascq ER -