TY - JOUR A1 - Finger, Felix A1 - Götten, Falk T1 - Neue Ansätze für die Entwicklung von unbemannten Fluggeräten JF - Ingenieurspiegel N2 - Wie sieht das unbemannte Flugzeug von Übermorgen aus? Dieser Frage stellen sich Forscher an der Fachhochschule Aachen. Die weltweit rasant fortschreitende Entwicklung des Marktes für unbemannte Fluggeräte (UAVs - „Unmanned Aerial Vehicles“) bietet großes Potenzial für Wachstum und Wertschöpfung. Unbemannte fliegende Systeme können – für bestimmte Anwendungsgebiete – wesentlich günstiger, kleiner und effizienter ausgelegt werden als bemannte Lösungen. Dabei sind sich viele Unternehmen über das mögliche Potential dieser Technologie noch gar nicht bewusst. Y1 - 2019 SN - 1868-5919 N1 - Project: UAV Design VL - 2019 IS - 1 SP - 67 EP - 68 ER - TY - CHAP A1 - Bergmann, Kevin A1 - Gräbener, Josefine A1 - Wild, Dominik A1 - Ulfers, H. A1 - Czupalla, Markus T1 - Study on thermal stabilization of a GEO-stationary telescope baffling system by integral application of phase change material T2 - International Conference on Environmental Systems N2 - The utilization of phase change material (PCM) for latent heat storage and thermal control of spacecraft has been demonstrated in the past in few missions only. One limiting factor was the fact that all concepts developed so far envisioned the PCM to be applied as an additional capacitor, encapsulated in its own housing, leading to mass, efficiency and accommodation challenges. Recently, the application of PCM within the scan cavity of a GEOS type satellite has been suggested, in order to tackle thermal issues due to direct sun intrusion (Choi, M., 2014). However, the application of PCM in such complex mechanical structures is extremely challenging. A new concept to tackle this issue is currently under development at the FH Aachen University of Applied Sciences. The concept "Infused Thermal Solutions (ITS)" is based on the idea to 3D print metallic structures in their regular functional shape, but double walled with internal lattice support structures, allowing the infusion of a PCM layer directly into the voids and eliminating the need for additional parts and interfaces. Together with OHB System, FH Aachen theoretically studied the application of this technology to the Meteosat Third Generation (MTG) Infra-Red Sounder (IRS) instrument. The study focuses on the scan cavity and entrance baffling assembly (EBA) of the IRS. It consists of thermal analyses, 3D-redesign and bread boarding of a scaled and PCM infused EBA version. In the thermal design of the alternative EBA, PCM was applied directly into the EBA, simulating the worst hot case sun intrusion of the mission. By applying 4kg of PCM (to a 60kg baffle) the EBA temperature excursions during sun intrusion were limited from 140K to 30K, leading to a significant thermo-opto-elastic performance gain. This paper introduces the ITS concept development status. Y1 - 2019 N1 - 49th International Conference on Environmental Systems, 7-11 July 2019, Boston, Massachusetts ; ICES-2019-72 SP - 1 EP - 14 ER - TY - THES A1 - Beckmann, Nils T1 - Characterization of the hydrogen-dry-low-Nox-micromix-combustion-principle for hydrogen-methane fuel mixtures KW - Low NOx KW - Hydrogen KW - Combustion KW - Low emission Y1 - 2019 N1 - Dissertation, RMIT University, August 2019 PB - RMIT University CY - Melbourne ER - TY - JOUR A1 - Göttsche, Joachim A1 - Alexopoulos, Spiros A1 - Dümmler, Andreas A1 - Maddineni, S. K. T1 - Multi-Mirror Array Calculations With Optical Error N2 - The optical performance of a 2-axis solar concentrator was simulated with the COMSOL Multiphysics® software. The concentrator consists of a mirror array, which was created using the application builder. The mirror facets are preconfigured to form a focal point. During tracking all mirrors are moved simultaneously in a coupled mode by 2 motors in two axes, in order to keep the system in focus with the moving sun. Optical errors on each reflecting surface were implemented in combination with the solar angular cone of ± 4.65 mrad. As a result, the intercept factor of solar radiation that is available to the receiver was calculated as a function of the transversal and longitudinal angles of incidence. In addition, the intensity distribution on the receiver plane was calculated as a function of the incidence angles. KW - solar process heat KW - concentrating collector KW - raytracing KW - point-focussing system Y1 - 2019 SP - 1 EP - 6 ER - TY - BOOK A1 - Schmidt, Bernd T1 - Grundlagen der Elektrotechnik und Elektronik für Ingenieure der Schienenfahrzeugtechnik und anderer Fachrichtungen : neu mit neuem SI-System und weiteren Inhalten für Mechantroniker KW - Elektrotechnik KW - Elektronik Y1 - 2019 SN - 978-3-944131-04-7 PB - B. Schmidt, Fachverlag für Elektro- und Informationstechnik CY - Bielefeld ET - 3. vollständig überarbeitete Auflage ER - TY - CHAP A1 - Marinković, Marko A1 - Butenweg, Christoph ED - Papadrakakis, Manolis ED - Fragiadakis, Michalis T1 - Experimental and numerical analysis of RC frames with decoupled masonry infills T2 - 7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering N2 - Masonry infill walls are commonly used in reinforced concrete (RC) frame structures, also in seismically active areas, although they often experience serious damage during earthquakes. One of the main reasons for their poor behaviour is the connection to the frame, which is usually constructed using mortar. This paper describes the novel solution for infill/frame connection based on application of elastomeric material between them. The system called INODIS (Innovative Decoupled Infill System) has the aim to postpone the activation of infill in in-plane direction and at the same time to provide sufficient out-of-plane support. First, experimental tests on infilled frame specimens are presented and the comparison of the results between traditionally infilled frames and infilled frames with the INODIS system are given. The results are then used for calibration and validation of numerical model, which can be further employed for investigating the influence of some material parameters on the behaviour of infilled frames with the INODIS system. KW - Earthquake KW - In-plane KW - Out-of-plane KW - Isolation KW - Seismic Y1 - 2019 SN - 978-618-82844-5-6 U6 - http://dx.doi.org/10.7712/120119.7088.18845 SN - 2623-3347 N1 - COMPDYN 2019, 24-26 June 2019, Crete, Greece. SP - 2464 EP - 2479 PB - National Technical University of Athens CY - Athen ER - TY - CHAP A1 - Michel, Philipp A1 - Alder, Philipp A1 - Butenweg, Christoph A1 - Klinkel, Sven T1 - Berechnung der Fluid-Struktur-Interaktion für flexibel gelagerte Flüssigkeitstanks T2 - 16. D-A-CH Tagung Erdbebeningenieurwesen & Baudynamik: 26. und 27. September 2019, Universität Innsbruck Y1 - 2019 SN - 978-3-200-06454-6 ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - On an asymptotic relative efficiency concept based on expected volumes of confidence regions JF - Statistics - A Journal of Theoretical and Applied Statistic N2 - The paper deals with an asymptotic relative efficiency concept for confidence regions of multidimensional parameters that is based on the expected volumes of the confidence regions. Under standard conditions the asymptotic relative efficiencies of confidence regions are seen to be certain powers of the ratio of the limits of the expected volumes. These limits are explicitly derived for confidence regions associated with certain plugin estimators, likelihood ratio tests and Wald tests. Under regularity conditions, the asymptotic relative efficiency of each of these procedures with respect to each one of its competitors is equal to 1. The results are applied to multivariate normal distributions and multinomial distributions in a fairly general setting. KW - Volume of confidence regions KW - asymptotic relative efficiency KW - likelihood ratio test KW - multivariate normal distribution KW - multinomial distribution Y1 - 2019 U6 - http://dx.doi.org/10.1080/02331888.2019.1683560 SN - 1029-4910 VL - 53 IS - 6 SP - 1396 EP - 1436 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Gaigall, Daniel T1 - On a new approach to the multi-sample goodness-of-fit problem JF - Communications in Statistics - Simulation and Computation N2 - Suppose we have k samples X₁,₁,…,X₁,ₙ₁,…,Xₖ,₁,…,Xₖ,ₙₖ with different sample sizes ₙ₁,…,ₙₖ and unknown underlying distribution functions F₁,…,Fₖ as observations plus k families of distribution functions {G₁(⋅,ϑ);ϑ∈Θ},…,{Gₖ(⋅,ϑ);ϑ∈Θ}, each indexed by elements ϑ from the same parameter set Θ, we consider the new goodness-of-fit problem whether or not (F₁,…,Fₖ) belongs to the parametric family {(G₁(⋅,ϑ),…,Gₖ(⋅,ϑ));ϑ∈Θ}. New test statistics are presented and a parametric bootstrap procedure for the approximation of the unknown null distributions is discussed. Under regularity assumptions, it is proved that the approximation works asymptotically, and the limiting distributions of the test statistics in the null hypothesis case are determined. Simulation studies investigate the quality of the new approach for small and moderate sample sizes. Applications to real-data sets illustrate how the idea can be used for verifying model assumptions. KW - Goodness-of-fit test KW - Multi-sample problem KW - Parametric bootstrap Y1 - 2019 U6 - http://dx.doi.org/10.1080/03610918.2019.1618472 SN - 1532-4141 VL - 53 IS - 10 SP - 2971 EP - 2989 PB - Taylor & Francis CY - London ER - TY - GEN T1 - 2. Ordnung zur Änderung der Beitragsordnung der Studierendenschaft der Fachhochschule Aachen : vom 7. November 2019 T3 - FH-Mitteilungen - 115/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Beitragsordnung der Studierendenschaft Y1 - 2019 ER - TY - GEN T1 - Beitragsordnung der Studierendenschaft der Fachhochschule Aachen : vom 11. Dezember 2018 – FH-Mitteilung Nr. 168/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 7. November 2019 – FH-Mitteilung Nr. 115/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 116/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Beitragsordnung der Studierendenschaft Y1 - 2019 ER - TY - GEN T1 - Gesamtprüfungsordnung für den Bachelorstudiengang „Bauingenieurwesen mit Orientierungssemester“ an der Fachhochschule Aachen und der RWTH Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 117/2019 KW - Amtliche Mitteilung KW - Gesamtprüfungsordnung KW - Bachelor KW - Bauingenieurwesen mit Orientierungssemester KW - RWTH Aachen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für die Bachelorstudiengänge Bauingenieurwesen, Bauingenieurwesen mit Praxissemester, Bauingenieurwesen mit Auslandssemester, Bauingenieurwesen Double Degree (NUST) und Bauingenieurwesen Dual an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 118/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge Bauingenieurwesen, Bauingenieurwesen mit Praxissemester, Bauingenieurwesen mit Auslandssemester, Bauingenieurwesen Double Degree (NUST), Bauingenieurwesen Dual und Bauingenieurwesen mit Orientierungssemester im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 28. Juni 2018 – FH-Mitteilung Nr. 89/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 8. November 2019 – FH-Mitteilung Nr. 118/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 119/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für den Bachelorstudiengang Holzingenieurwesen im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 120/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge Holzingenieurwesen, Holzingenieurwesen mit Praxissemester, Holzingenieurwesen mit Auslandssemester, Holzingenieurwesen Dual und Holzingenieurwesen mit Orientierungssemester : vom 28. Juni 2018 – FH-Mitteilung Nr. 90/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 8. November 2019 – FH-Mitteilung Nr. 120/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 121/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Zugangsordnung für die Masterstudiengänge „Energiewirtschaft & Informatik“ (3 Semester) und „Energiewirtschaft & Informatik“ (4 Semester) Fachbereich Energietechnik Fachbereich Medizintechnik und Technomathematik an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 122/2019 KW - Amtliche Mitteilung KW - Zugangsordnung KW - Master KW - Energiewirtschaft KW - Informatik Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für die Masterstudiengänge „Energiewirtschaft & Informatik“ (3 Semester) und „Energiewirtschaft & Informatik“ (4 Semester) Fachbereich Energietechnik Fachbereich Medizintechnik und Technomathematik an der Fachhochschule Aachen : vom 8. November 2019 T3 - FH-Mitteilungen - 123/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Energiewirtschaft KW - Informatik Y1 - 2019 ER - TY - GEN T1 - Richtlinie zur Durchführung von Sonderveranstaltungen in den Gebäuden und Liegenschaften der FH Aachen (Veranstaltungsrichtlinie) : vom 20. November 2019 T3 - FH-Mitteilungen - 124a/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - Veranstaltungsrichtlinie KW - Durchführung von Sonderveranstaltungen Y1 - 2019 ER - TY - GEN T1 - Richtlinie zur Durchführung von Sonderveranstaltungen in den Gebäuden und Liegenschaften der FH Aachen (Veranstaltungsrichtlinie) : vom 20. November 2019 Anlage 1 aktualisiert am 22. Januar 2020 T3 - FH-Mitteilungen - 124b/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - Veranstaltungsrichtlinie KW - Durchführung von Sonderveranstaltungen KW - Aktualisierung Y1 - 2019 ER - TY - GEN T1 - Richtlinie für die Beschäftigung und Vergütung studentischer und wissenschaftlicher Hilfskräfte an der Fachhochschule Aachen : vom 20. November 2019 T3 - FH-Mitteilungen - 125a/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - studentische Hilfskräfte KW - wissenschaftliche Hilfkräfte Y1 - 2019 ER - TY - GEN T1 - Richtlinie für die Beschäftigung und Vergütung studentischer und wissenschaftlicher Hilfskräfte an der Fachhochschule Aachen : vom 20. November 2019 aktualisiert am 24. November 2022 T3 - FH-Mitteilungen - 125b/2019 KW - Amtliche Mitteilung KW - Richtlinie KW - studentische Hilfskräfte KW - wissenschaftliche Hilfkräfte Y1 - 2019 ER - TY - GEN T1 - Gleichstellungsquoten der FH Aachen für die Jahre 2019 –2021 : vom 20. November 2019 T3 - FH-Mitteilungen - 126/2019 KW - Amtliche Mitteilung KW - Gleichstellungsquoten KW - 2019 KW - 2020 KW - 2021 Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnungen für den Masterstudiengang „Nuclear Applications“ vom 13. Februar 2004 (FH-Mitteilung Nr. 5/2004) und vom 25. Februar 2010 (FH-Mitteilung Nr. 15/2010) in den Fassungen der Bekanntmachung der Änderungsordnungen vom 6. November 2012 (FH-Mitteilung Nr. 120/2012), 18. Juni 2014 (FH- Mitteilung Nr. 72/2014) und vom 15. Juni 2015 (FH-Mitteilung Nr. 28/2015) : vom 29. November 2019 T3 - FH-Mitteilungen - 127/2019 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Nuclear Applications Y1 - 2023 ER - TY - GEN T1 - 5. Ordnung zur Änderung der Prüfungsordnung für die Bachelorstudiengänge „Betriebswirtschaft Praxis Plus“ und „Betriebswirtschaft Praxis Plus (Teilzeit)“ mit dem Studienabschluss „Bachelor of Science“ am Fachbereich Wirtschaftswissenschaften der Fachhochschule Aachen (PO – BWL Praxis Plus) : vom 29. November 2019 T3 - FH-Mitteilungen - 128/2019 KW - Amtliche Mitteilung KW - Änderungsordnung KW - Prüfungsordnung KW - Bachelor KW - Betriebswirtschaft Praxis Plus Y1 - 2023 ER - TY - GEN T1 - Prüfungsordnung für die Bachelorstudiengänge „Betriebswirtschaft Praxis Plus“ und „Betriebswirtschaft Praxis Plus (Teilzeit)“ mit dem Studienabschluss „Bachelor of Science“ am Fachbereich Wirtschaftswissenschaften der Fachhochschule Aachen (PO-BWL Praxis Plus) : vom 14. Januar 2014 – FH-Mitteilung Nr. 2/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 29. November 2019 – FH-Mitteilung Nr. 128/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab WS 2019/20) T3 - FH-Mitteilungen - 129/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Bachelor KW - Betriebswirtschaft Praxis Plus Y1 - 2023 ER - TY - GEN T1 - 2. Änderung der Richtlinie des Rektorats der FH Aachen für die Vergabe von Lehrveranstaltungsprämien : vom 13. Dezember 2019 T3 - FH-Mitteilungen - 130/2019 KW - Amtliche Mitteilung KW - Änderung KW - Richtlinie KW - Rektorat KW - Lehrveranstaltungsprämien Y1 - 2019 ER - TY - GEN T1 - Richtlinie des Rektorats der FH Aachen für die Vergabe von Lehrveranstaltungsprämien : vom 16. Juli 2012 – FH-Mitteilung Nr. 68/2012 in der Fassung der Bekanntmachung der Änderung vom 13. Dezember 2019 – FH-Mitteilung Nr. 130/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 131/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Richtlinie KW - Rektorat KW - Lehrveranstaltungsprämien Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den Masterstudiengang Nuclear Applications im Fachbereich Chemie und Biotechnologie an der Fachhochschule Aachen : vom 17. Dezember 2019 T3 - FH-Mitteilungen - 132/2019 KW - Amtliche Mitteilung KW - Prüfungsordnung KW - Master KW - Nuclear Applications KW - Chemie und Biotechnologie Y1 - 2019 ER - TY - GEN A1 - Blottner, Dieter A1 - Hastermann, Maria A1 - Muckelt, Paul A1 - Albracht, Kirsten A1 - Schoenrock, Britt A1 - Salanova, Michele A1 - Warner, Martin A1 - Gunga, Hans-Christian A1 - Stokes, Maria T1 - MYOTONES - Inflight muscle health status monitoring during long-duration space missions onboard the International Space Station: a single case study T2 - IAC Papers Archive N2 - The MYOTONES experiment is the first to monitor changes in the basic biomechanical properties (tone, elasticity and stiffness) of the resting human myofascial system due to microgravity with a oninvasive, portable device on board the ISS. The MyotonPRO device applies several brief mechanical stimuli to the surface of the skin, and the natural oscillation signals of the tissue beneath are detected and computed by the MyotonPRO. Thus, an objective, quick and easy determination of the state of the underlying tissue is possible. Two preflight, four inflight and four post flight measurements were performed on a male astronaut using the same 10 measurement points (MP) for each session. MPs were located on the plantar fascia, Achilles tendon, M. soleus, M. gastrocnemius, M. multifidus, M. splenius capitis, M. deltoideus anterior, M. rectus femoris, infrapatellar tendon, M. tibialis anterior. Subcutaneous tissues thickness above the MPs was measured using ultrasound imaging. Magnetic resonance images (MRI) of lower limb muscles and functional tests were also performed pre- and postflight. Our first measurements on board the ISS confirmed increased tone and stiffness of the lumbar multifidus muscle, an important trunk stabilizer, dysfunction of which is known to be associated with back pain. Furthermore, reduced tone and stiffness of Achilles tendon and plantar fascia were observed inflight vs. preflight, confirming previous findings from terrestrial analog studies and parabolic flights. Unexpectedly, the deltoid showed negative inflight changes in tone and stiffness, and increased elasticity, suggesting a potential risk of muscle atrophy in longer spaceflight that should be addressed by adequate inflight countermeasure protocols. Most values from limb and back MPS showed deflected patterns (in either directions) from inflight shortly after the re-entry phase on the landing day and one week later. Most parameter values then normalized to baseline after 3 weeks likely due to 1G re-adaptation and possible outcome of the reconditioning protocol. No major changes in subcutaneous tissues thickness above the MPs were found inflight vs preflight, suggesting no bias (i.e., fluid shift, extreme tissue thickening or loss). Pre- and postflight MRI and functional tests showed negligible changes in calf muscle size, power and force, which is likely due to training effects from current inflight exercise protocols. The MYOTONES experiment is currently ongoing to collect data from further crew members. The potential impact of this research is to better understand the effects of microgravity and countermeasures over the time course of an ISS mission cycle. This will enable exercise countermeasures to be tailored Y1 - 2019 SN - 00741795 N1 - International Astronautical Congress: space: the power of the past, the promise of the future - Washington DC, USA/Vereinigte Staaten von Amerika Dauer: 21.10.2019 → 25.10.2019 PB - Pergamon CY - Oxford ER - TY - JOUR A1 - Werkhausen, Amelie A1 - Cronin, Neil J. A1 - Albracht, Kirsten A1 - Paulsen, Gøran A1 - Larsen, Askild V. A1 - Bojsen-Møller, Jens A1 - Seynnes, Olivier R. T1 - Training-induced increase in Achilles tendon stiffness affects tendon strain pattern during running JF - PeerJ N2 - Background During the stance phase of running, the elasticity of the Achilles tendon enables the utilisation of elastic energy and allows beneficial contractile conditions for the triceps surae muscles. However, the effect of changes in tendon mechanical properties induced by chronic loading is still poorly understood. We tested the hypothesis that a training-induced increase in Achilles tendon stiffness would result in reduced tendon strain during the stance phase of running, which would reduce fascicle strains in the triceps surae muscles, particularly in the mono-articular soleus. Methods Eleven subjects were assigned to a training group performing isometric singleleg plantarflexion contractions three times per week for ten weeks, and another ten subjects formed a control group. Before and after the training period, Achilles tendon stiffness was estimated, and muscle-tendon mechanics were assessed during running at preferred speed using ultrasonography, kinematics and kinetics. Results Achilles tendon stiffness increased by 18% (P <0:01) in the training group, but the associated reduction in strain seen during isometric contractions was not statistically significant. Tendon elongation during the stance phase of running was similar after training, but tendon recoil was reduced by 30% (P <0:01), while estimated tendon force remained unchanged. Neither gastrocnemius medialis nor soleus fascicle shortening during stance was affected by training. Discussion These results show that a training-induced increase in Achilles tendon stiffness altered tendon behaviour during running. Despite training-induced changes in tendon mechanical properties and recoil behaviour, the data suggest that fascicle shortening patterns were preserved for the running speed that we examined. The asymmetrical changes in tendon strain patterns supports the notion that simple inseries models do not fully explain the mechanical output of the muscle-tendon unit during a complex task like running. KW - Achilles tendon KW - Stiffness KW - Running KW - Tendon properties KW - Architectural gear ratio Y1 - 2019 U6 - http://dx.doi.org/10.7717/peerj.6764 SN - 21678359 PB - Peer CY - London ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnung für den Masterstudiengang „Information Systems Engineering“ vom 22. Januar 2010 (FH-Mitteilung Nr. 5/2010), zuletzt geändert durch Änderungsordnung vom 4. Februar 2013 (FH-Mitteilung Nr. 6/2013) : vom 20. Dezember 2019 T3 - FH-Mitteilungen - 133/2019 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Information Systems Engineering Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Prüfungsordnung für den Masterstudiengang „Elektrotechnik“ (zuvor „Nachrichtentechnik“ und „Elektrotechnik und Informationstechnik“) vom 22. Januar 2010 (FH-Mitteilung Nr. 7/2010), zuletzt geändert durch Änderungsordnung vom 25. April 2016 (FH-Mitteilung Nr. 31/2016) : vom 20. Dezember 2019 T3 - FH-Mitteilungen - 134/2019 KW - Amtliche Mitteilung KW - Aufhebungsordnung KW - Prüfungsordnung KW - Master KW - Elektrotechnik Y1 - 2019 ER - TY - JOUR A1 - Ketelhut, Maike A1 - Kolditz, Melanie A1 - Göll, Fabian A1 - Braunstein, Bjoern A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Admittance control of an industrial robot during resistance training JF - IFAC-PapersOnLine N2 - Neuromuscular strength training of the leg extensor muscles plays an important role in the rehabilitation and prevention of age and wealth related diseases. In this paper, we focus on the design and implementation of a Cartesian admittance control scheme for isotonic training, i.e. leg extension and flexion against a predefined weight. For preliminary testing and validation of the designed algorithm an experimental research and development platform consisting of an industrial robot and a force plate mounted at its end-effector has been used. Linear, diagonal and arbitrary two-dimensional motion trajectories with different weights for the leg extension and flexion part are applied. The proposed algorithm is easily adaptable to trajectories consisting of arbitrary six-dimensional poses and allows the implementation of individualized trajectories. KW - Assistive technology KW - Rehabilitation engineering KW - Human-Computer interaction KW - Automatic control Y1 - 2019 U6 - http://dx.doi.org/10.1016/j.ifacol.2019.12.102 SN - 2405-8963 N1 - 14th IFAC Symposium on Analysis, Design, and Evaluation of Human Machine Systems HMS 2019 Tallinn, Estonia, 16–91 September 2019 VL - 52 IS - 19 SP - 223 EP - 228 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Ketelhut, Maike A1 - Göll, Fabian A1 - Braunstein, Bjoern A1 - Albracht, Kirsten A1 - Abel, Dirk T1 - Iterative learning control of an industrial robot for neuromuscular training T2 - 2019 IEEE Conference on Control Technology and Applications N2 - Effective training requires high muscle forces potentially leading to training-induced injuries. Thus, continuous monitoring and controlling of the loadings applied to the musculoskeletal system along the motion trajectory is required. In this paper, a norm-optimal iterative learning control algorithm for the robot-assisted training is developed. The algorithm aims at minimizing the external knee joint moment, which is commonly used to quantify the loading of the medial compartment. To estimate the external knee joint moment, a musculoskeletal lower extremity model is implemented in OpenSim and coupled with a model of an industrial robot and a force plate mounted at its end-effector. The algorithm is tested in simulation for patients with varus, normal and valgus alignment of the knee. The results show that the algorithm is able to minimize the external knee joint moment in all three cases and converges after less than seven iterations. KW - Knee KW - Training KW - Load modeling KW - Force KW - Iterative learning control Y1 - 2019 SN - 978-1-7281-2767-5 (ePub) SN - 978-1-7281-2766-8 (USB) SN - 978-1-7281-2768-2 (PoD) U6 - http://dx.doi.org/10.1109/CCTA.2019.8920659 N1 - 2019 IEEE Conference on Control Technology and Applications (CCTA) Hong Kong, China, August 19-21, 2019 PB - IEEE CY - New York ER - TY - BOOK A1 - Uibel, Thomas A1 - Peterson, Leif Arne ED - Uibel, Thomas ED - Peterson, Leif Arne T1 - Tagungsband Aachener Holzbautagung 2019 Y1 - 2019 SN - 2197-4489 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Achtsnicht, Stefan A1 - Pourshahidi, Ali Mohammad A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim T1 - Multiplex detection of different magnetic beads using frequency scanning in magnetic frequency mixing technique JF - Sensors N2 - In modern bioanalytical methods, it is often desired to detect several targets in one sample within one measurement. Immunological methods including those that use superparamagnetic beads are an important group of techniques for these applications. The goal of this work is to investigate the feasibility of simultaneously detecting different superparamagnetic beads acting as markers using the magnetic frequency mixing technique. The frequency of the magnetic excitation field is scanned while the lower driving frequency is kept constant. Due to the particles’ nonlinear magnetization, mixing frequencies are generated. To record their amplitude and phase information, a direct digitization of the pickup-coil’s signal with subsequent Fast Fourier Transformation is performed. By synchronizing both magnetic beads using frequency scanning in magnetic frequency mixing technique magnetic fields, a stable phase information is gained. In this research, it is shown that the amplitude of the dominant mixing component is proportional to the amount of superparamagnetic beads inside a sample. Additionally, it is shown that the phase does not show this behaviour. Excitation frequency scans of different bead types were performed, showing different phases, without correlation to their diverse amplitudes. Two commercially available beads were selected and a determination of their amount in a mixture is performed as a demonstration for multiplex measurements. KW - frequency mixing magnetic detection KW - magnetic sandwich immunoassay KW - multiparametric immunoassays Y1 - 2019 U6 - http://dx.doi.org/10.3390/s19112599 SN - 1424-8220 VL - 19 IS - 11 PB - MDPI CY - Basel ER - TY - JOUR A1 - Achtsnicht, Stefan A1 - Tödter, Julia A1 - Niehues, Julia A1 - Telöken, Matthias A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim A1 - Schröper, Florian T1 - 3D printed modular immunofiltration columns for frequency mixing-based multiplex magnetic immunodetection JF - Sensors N2 - For performing point-of-care molecular diagnostics, magnetic immunoassays constitute a promising alternative to established enzyme-linked immunosorbent assays (ELISA) because they are fast, robust and sensitive. Simultaneous detection of multiple biomolecular targets from one body fluid sample is desired. The aim of this work is to show that multiplex magnetic immunodetection based on magnetic frequency mixing by means of modular immunofiltration columns prepared for different targets is feasible. By calculations of the magnetic response signal, the required spacing between the modules was determined. Immunofiltration columns were manufactured by 3D printing and antibody immobilization was performed in a batch approach. It was shown experimentally that two different target molecules in a sample solution could be individually detected in a single assaying step with magnetic measurements of the corresponding immobilization filters. The arrangement order of the filters and of a negative control did not influence the results. Thus, a simple and reliable approach to multi-target magnetic immunodetection was demonstrated. Y1 - 2019 U6 - http://dx.doi.org/10.3390/s19010148 SN - 1424-8220 VL - 19 IS - 1 PB - MDPI CY - Basel ER - TY - JOUR A1 - Achtsnicht, Stefan A1 - Schönenborn, Kristina A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim T1 - Measurement of the magnetophoretic velocity of different superparamagnetic beads JF - Journal of Magnetism and Magnetic Materials N2 - The movement of magnetic beads due to a magnetic field gradient is of great interest in different application fields. In this report we present a technique based on a magnetic tweezers setup to measure the velocity factor of magnetically actuated individual superparamagnetic beads in a fluidic environment. Several beads can be tracked simultaneously in order to gain and improve statistics. Furthermore we show our results for different beads with hydrodynamic diameters between 200 and 1000 nm from diverse manufacturers. These measurement data can, for example, be used to determine design parameters for a magnetic separation system, like maximum flow rate and minimum separation time, or to select suitable beads for fixed experimental requirements. KW - magnetophoretic velocity KW - superparamagnetic bead KW - magnetic tweezers KW - magnetic separation KW - magnetic actuation Y1 - 2019 U6 - http://dx.doi.org/10.1016/j.jmmm.2018.10.066 SN - 0304-8853 VL - 477 IS - 1 SP - 244 EP - 248 PB - Elsevier CY - Amsterdam ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für den Masterstudiengang Architektur im Fachbereich Architektur an der Fachhochschule Aachen N2 - Aufgrund des § 2 Absatz 4 Satz 1 in Verbindung mit § 64 des Gesetzes über die Hochschulen des Landes Nordrhein-Westfalen (Hochschulgesetz – HG) vom 16. September 2014 (GV. NRW. S. 547), zuletzt geändert durch Artikel 3 des Gesetzes vom 17. Oktober 2017 (GV. NRW. S. 806), und der Rahmenprüfungsordnung (RPO) für die Bachelor- und Masterstudiengänge an der Fachhochschule Aachen vom 1. Februar 2018 (FH-Mitteilung Nr. 3/2018) hat der Fachbereich Architektur folgende Änderung der Prüfungsordnung vom 5. Juli 2018 (FH-Mitteilung Nr. 105/2018) erlassen. T3 - FH-Mitteilungen - 67/2019 KW - Amtliche Mitteilung KW - Master Architektur KW - Prüfungsordnung Y1 - 2019 ER - TY - GEN T1 - Prüfungsordnung für den Bachelorstudiengang Architektur im Fachbereich Architektur an der Fachhochschule Aachen BT - vom 5. Juli 2018 – FH-Mitteilung Nr. 104/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 17. Juli 2019 – FH-Mitteilung Nr. 66/2019 (nichtamtliche lesbare Fassung | Studienbeginn ab WS 2019/20) T3 - FH-Mitteilungen - 68/2019 KW - Amtliche Mitteilungen KW - Bachelor KW - Prüfungsordnung Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Änderung der Prüfungsordnung für den Bachelorstudiengang Architektur im Fachbereich Architektur an der Fachhochschule Aachen N2 - Aufgrund des § 2 Absatz 4 Satz 1 in Verbindung mit § 64 des Gesetzes über die Hochschulen des Landes Nordrhein-Westfalen (Hochschulgesetz – HG) vom 16. September 2014 (GV. NRW. S. 547), zuletzt geändert durch Artikel 3 des Gesetzes vom 17. Oktober 2017 (GV. NRW. S. 806), und der Rahmenprüfungsordnung (RPO) für die Bachelor- und Masterstudiengänge an der Fachhochschule Aachen vom 1. Februar 2018 (FH-Mitteilung Nr. 3/2018) hat der Fachbereich Architektur folgende Änderung der Prüfungsordnung vom 5. Juli 2018 (FH-Mitteilung Nr. 104/2018) erlassen. T3 - FH-Mitteilungen - 66/2019 KW - Prüfungsordnung KW - Bachelor KW - Amtliche Mitteilungen Y1 - 2019 CY - Aachen ER - TY - GEN T1 - Prüfungsordnung für den dreisemestrigen Masterstudiengang „Industrial Engineering“ an der Fachhochschule Aachen : vom 11. Dezember 2014 – FH-Mitteilung Nr. 154/2014 in der Fassung der Bekanntmachung der Änderungsordnung vom 5. Februar 2019 – FH-Mitteilung Nr. 5/2019 (Nichtamtliche lesbare Fassung | Studienbeginn ab SS 2016) T3 - FH-Mitteilungen - 104/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Prüfungsordnung KW - Master KW - Industrial Engineering Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den Bachelorstudiengang Bauingenieurwesen (7-semestrig), Bachelorstudiengang Bauingenieurwesen mit Praxissemester (8-semestrig), Bachelorstudiengang Bauingenieurwesen mit Auslandssemester (8-semestrig) Abschluss Bachelor of Engineering : vom 1. September 2011 – FH-Mitteilung Nr. 76/2011 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 74/2019 (Nichtamtliche lesbare Fassung, Studienbeginn WS 2016/17–2017/18) T3 - FH-Mitteilungen - 85/2019 KW - Amtliche Mitteilung KW - Studien- und Prüfungsordnung KW - Lesbare Fassung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für die Bachelorstudiengänge „Bauingenieurwesen“ (7-semestrig), „Bauingenieurwesen mit Praxissemester“ (8-semestrig) und „Bauingenieurwesen mit Auslandssemester“ (8-semestrig) vom 1. September 2011 (FH-Mitteilung Nr. 76/2011) in der Fassung der Bekanntmachung der Änderungsordnungen vom 22. August 2013 (FH-Mitteilung Nr. 88/2013), 8. Juni 2016 (FH-Mitteilung Nr. 80/2016) und 16. August 2019 (FH-Mitteilung Nr. 74/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 119/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 75/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 86/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung des Studiengangs Holzingenieurwesen (7-semestrig) – Abschluss Bachelor of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 66/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 76/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 87/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Ordnung zur Aufhebung der Studien- und Prüfungsordnung für den Bachelorstudiengang „Holzingenieurwesen“ (7-semestrig) vom 16. Juli 2012 (FH-Mitteilung Nr. 66/2012) in der Fassung der Bekanntmachung der Änderungsordnungen vom 6. Juli 2016 (FH-Mitteilung Nr. 95/2016) und 16. August 2019 (FH-Mitteilung Nr. 76/2019) an der Fachhochschule Aachen : vom 24. Juli 2018 – FH-Mitteilung Nr. 120/2018 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 77/2019 (Nichtamtliche lesbare Fassung) T3 - FH-Mitteilungen - 88/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Holzingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung des Studiengangs Bauingenieurwesen – Netzingenieur – Abschluss Bachelor of Engineering – im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung | Studienbeginn WS 2011/12–2013/14) T3 - FH-Mitteilungen - 89/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den dualen Bachelorstudiengang Bauingenieurwesen – Netzingenieur (9 Semester) und den Bachelorstudiengang Bauingenieurwesen – Netzingenieur (7 Semester) Abschluss Bachelor of Engineering im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung, Studienbeginn WS 2014/15–2016/17) T3 - FH-Mitteilungen - 90/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER - TY - GEN T1 - Studien- und Prüfungsordnung für den dualen Bachelorstudiengang Bauingenieurwesen – Netzingenieur (9 Semester) und den Bachelorstudiengang Bauingenieurwesen – Netzingenieur (7 Semester) Abschluss Bachelor of Engineering im Fachbereich Bauingenieurwesen an der Fachhochschule Aachen : vom 16. Juli 2012 – FH-Mitteilung Nr. 67/2012 in der Fassung der Bekanntmachung der Änderungsordnung vom 16. August 2019 – FH-Mitteilung Nr. 78/2019 (Nichtamtliche lesbare Fassung, Studienbeginn ab WS 2017/18) T3 - FH-Mitteilungen - 91/2019 KW - Amtliche Mitteilung KW - Lesbare Fassung KW - Studien- und Prüfungsordnung KW - Bachelor KW - Bauingenieurwesen Y1 - 2019 ER -