TY  - CHAP
A1  - Marinković, Marko
A1  - Butenweg, Christoph
ED  - Papadrakakis, Manolis
ED  - Fragiadakis, Michalis
T1  - Experimental and numerical analysis of RC frames with decoupled masonry infills
T2  - 7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering
N2  - Masonry infill walls are commonly used in reinforced concrete (RC) frame structures, also in seismically active areas, although they often experience serious damage during earthquakes. One of the main reasons for their poor behaviour is the connection to the frame, which is usually constructed using mortar. This paper describes the novel solution for infill/frame connection based on application of elastomeric material between them. The system called INODIS (Innovative Decoupled Infill System) has the aim to postpone the activation of infill in in-plane direction and at the same time to provide sufficient out-of-plane support. First, experimental tests on infilled frame specimens are presented and the comparison of the results between traditionally infilled frames and infilled frames with the INODIS system are given. The results are then used for calibration and validation of numerical model, which can be further employed for investigating the influence of some material parameters on the behaviour of infilled frames with the INODIS system.
KW  - Earthquake
KW  - In-plane
KW  - Out-of-plane
KW  - Isolation
KW  - Seismic
Y1  - 2019
SN  - 978-618-82844-5-6
U6  - http://dx.doi.org/10.7712/120119.7088.18845
SN  - 2623-3347
N1  - COMPDYN 2019, 24-26 June 2019, Crete, Greece.
SP  - 2464
EP  - 2479
PB  - National Technical University of Athens
CY  - Athen
ER  - 
TY  - CHAP
A1  - Marinković, Marko
A1  - Butenweg, Christoph
T1  - Out-of-plane behavior of decoupled masonry infills under seismic loading
T2  - 17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021.
N2  - Masonry is used in many buildings not only for load-bearing walls, but also for non-load-bearing enclosure elements in the  form  of infill  walls. Many  studies confirmed  that infill  walls interact  with the  surrounding  reinforced concrete frame, thus changing dynamic characteristics of the structure. Consequently, masonry infills cannot be neglected in the design process. However, although the relevant standards contain requirements for infill walls, they do not describe how these  requirements  are  to  be  met  concretely.  This  leads  in  practice  to  the  fact  that  the  infill  walls  are neither dimensioned nor constructed correctly. The evidence of this fact is confirmed by the recent earthquakes, which have led to enormous damages, sometimes followed by the total collapse  of buildings and loss  of human  lives. Recently, the increasing  effort has  been dedicated  to the  approach  of decoupling  of masonry  infills from  the  frame  elements by introducing the gap in between. This helps in removing the interaction between infills and frame, but raises the question of out-of-plane stability of the panel. This paper presents the results of the experimental campaign showing the out-of-plane  behavior of  masonry  infills decoupled  with the  system  called INODIS  (Innovative decoupled  infill system), developed within the European project INSYSME (Innovative Systems for Earthquake Resistant Masonry Enclosures in Reinforced  Concrete  Buildings).  Full  scale  specimens  were  subjected  to  the  different  loading  conditions  and combinations  of in-plane  and  out-of-plane loading.  Out-of-plane capacity  of the  masonry  infills  with the  INODIS system is compared with traditionally constructed infills, showing that INODIS system provides reliable out-of-plane connection under various loading conditions. In contrast, traditional infills performed very poor in the case of combined and simultaneously applied in-plane and out-of-plane loading, experiencing brittle behavior under small in-plane drifts followed by high out-of-plane displacements. Decoupled infills with the INODIS system have  remained stable under out-of-plane loads, even after reaching high in-plane drifts and being damaged.
KW  - in-plane
KW  - out-of-plane
KW  - INODIS
KW  - earthquake
KW  - connection detail
Y1  - 2020
N1  - Die Konferenz war ursprünglich für den 13-18 September 2020 angesetzt.
ER  - 
TY  - JOUR
A1  - Marinkovic, Marko
A1  - Butenweg, Christoph
T1  - Ausfachungen aus Ziegelmauerwerk in Stahlbetonrahmentragwerken unter Erdbebenbeanspruchung
JF  - Mauerwerk
N2  - Stahlbetonrahmentragwerke mit Ausfachungen aus Mauerwerk weisen nach Erdbeben häufig schwere Schäden auf. Gründe hierfür sind die Beanspruchungen der Ausfachungswände durch die aufgezwungenen Rahmenverformungen in Wandebene und die gleichzeitig auftretenden Trägheitskräfte senkrecht zur Wandebene in Kombination mit der konstruktiven Ausführung des Ausfachungsmauerwerks. Die Ausfachung wird in der Regel knirsch gegen die Rahmenstützen gemauert, wobei der Verschluss der oberen Fuge mit Mörtel oder Montageschaum erfolgt. Dadurch kommt es im Erdbebenfall zu lokalen Interaktionen zwischen Ausfachung und Rahmen, die in der Folge zu einem Versagen einzelner Ausfachungswände oder zu einem sukzessiven Versagen des Gesamtgebäudes führen können. Die beobachteten Schäden waren die Motivation dafür, in dem europäischen Forschungsprojekt INSYSME für Stahlbetonrahmentragwerke mit Ausfachungen aus hochwärmedämmenden Ziegelmauerwerk innovative Lösungen zur Verbesserung des seismischen Verhaltens zu entwickeln. Der vorliegende Beitrag stellt die im Rahmen des Projekts von den deutschen Projektpartnern (Universität Kassel, SDA-engineering GmbH) entwickelten Lösungen vor und vergleicht deren seismisches Verhalten mit der traditionellen Ausführung der Ausfachungswände. Grundlage für den Vergleich sind statisch-zyklische Wandversuche und Simulationen auf Wandebene. Aus den Ergebnissen werden Empfehlungen für die erdbebensichere Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk abgeleitet.
Y1  - 2020
U6  - http://dx.doi.org/10.1002/dama.202000011
SN  - 1437-1022
VL  - 24
IS  - 4
SP  - 194
EP  - 205
PB  - Wiley
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Marinkovic, Marko
A1  - Butenweg, Christoph
T1  - Earthquake-proof system for masonry infills in RC frame structures
JF  - International Journal of Masonry Research and Innovation
Y1  - 2020
U6  - http://dx.doi.org/10.1504/IJMRI.2020.106328
SN  - 2056-9467
VL  - 5
IS  - 2
SP  - 185
EP  - 208
PB  - Inderscience Enterprises
CY  - Olney, Bucks
ER  - 
TY  - JOUR
A1  - Marinkovic, Marko
A1  - Butenweg, Christoph
T1  - Innovative decoupling system for the seismic protection of masonry infill walls in reinforced concrete frames
JF  - Engineering Structures
Y1  - 2019
U6  - http://dx.doi.org/10.1016/j.engstruct.2019.109435
SN  - 0141-0296
VL  - 197
IS  - Article 109435
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Marinkovic, Marko
A1  - Butenweg, Christoph
T1  - Innovative System for Earthquake Resistant Masonry Infill Walls
T2  - 16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018
Y1  - 2018
N1  - Paper No 11479
SP  - 1
EP  - 12
ER  - 
TY  - CHAP
A1  - Marinkovic, Marko
A1  - Butenweg, Christoph
T1  - Seismic behaviour of RC frames with uncoupled masonry infills having two storeys or two bays
T2  - 17th International Conference -From historical to sustainable masonry, Krakow, Poland, July 5-8, 2020
Y1  - 2020
U6  - http://dx.doi.org/10.1201/9781003098508-72
SP  - 1
EP  - 7
ER  - 
TY  - JOUR
A1  - Marinkovic, Marko
A1  - Butenweg, Christoph
T1  - Numerical analysis of the in-plane behaviour of decoupled masonry infilled RC frames
JF  - Engineering Structures
N2  - Damage of reinforced concrete (RC) frames with masonry infill walls has been observed after many earthquakes. Brittle behaviour of the masonry infills in combination with the ductile behaviour of the RC frames makes infill walls prone to damage during earthquakes. Interstory deformations lead to an interaction between the infill and the RC frame, which affects the structural response. The result of this interaction is significant damage to the infill wall and sometimes to the surrounding structural system too. In most design codes, infill walls are considered as non-structural elements and neglected in the design process, because taking into account the infills and considering the interaction between frame and infill in software packages can be complicated and impractical. A good way to avoid negative aspects arising from this behavior is to ensure no or low-interaction of the frame and infill wall, for instance by decoupling the infill from the frame. This paper presents the numerical study performed to investigate new connection system called INODIS (Innovative Decoupled Infill System) for decoupling infill walls from surrounding frame with the aim to postpone infill activation to high interstory drifts thus reducing infill/frame interaction and minimizing damage to both infills and frames. The experimental results are first used for calibration and validation of the numerical model, which is then employed for investigating the influence of the material parameters as well as infill’s and frame’s geometry on the in-plane behaviour of the infilled frames with the INODIS system. For all the investigated situations, simulation results show significant improvements in behaviour for decoupled infilled RC frames in comparison to the traditionally infilled frames.
KW  - Seismic loading
KW  - Earthquake
KW  - In-plane performance, isolation
KW  - Infill wall design
KW  - Numerical modelling
Y1  - 2022
U6  - http://dx.doi.org/10.1016/j.engstruct.2022.114959
SN  - 0141-0296
VL  - 272
IS  - 1
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Lu, S.
A1  - Beyer, K.
A1  - Bosiljkov, V.
A1  - Butenweg, Christoph
A1  - D’Ayala, D.
A1  - Degee, H.
A1  - Gams, M.
A1  - Klouda, J.
A1  - Lagomarsino, S.
A1  - Penna, A.
A1  - Mojsilovic, N.
A1  - da Porto, F.
A1  - Sorrentino, L.
A1  - Vintzileou, E.
ED  - Modena, Claudio
ED  - da Porto, F.
ED  - Valluzzi, M.R.
T1  - Next generation of Eurocode 8, masonry chapter
T2  - Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016
N2  - This paper describes the procedure on the evaluation of the masonry chapter for the next generation of Eurocode 8, the European Standard for earthquake-resistant design. In CEN, TC 250/SC8, working group WG 1 has been established to support the subcommittee on the topic of masonry on both design of new structures (EN1998-1) and assessment of existing structures (EN1998-3). The aim is to elaborate suggestions for amendments which fit the current state of the art in masonry and earthquake-resistant design. Focus will be on modelling, simplified methods, linear-analysis (q-values, overstrength-values), nonlinear procedures, out-of-plane design as well as on clearer definition of limit states. Beside these, topics related to general material properties, reinforced masonry, confined masonry, mixed structures and non-structural infills will be covered too. This paper presents the preliminary work and results up to the submission date.
Y1  - 2016
SN  - 978-1-138-02999-6 (Print)
SN  - 9781315374963 (E-Book)
SP  - 695
EP  - 700
PB  - Taylor & Francis
CY  - London
ER  - 
TY  - CHAP
A1  - Losch, S.
A1  - Butenweg, Christoph
T1  - Qualitätsgesteuerte Bemessung von Stahlbetontragwerken mit der FE-Methode
T2  - 11. Forum Bauinformatik Darmstadt '99 : [Beiträge der Forumsteilnehmer, die im Rahmen des 11. Forums Bauinformatik vom 22. bis 24. September 1999 in Darmstadt ihre Forschung präsentiert ...] / Tobias Kuhn ... (Hrsg.) (Fortschritt-Berichte VDI : Reihe 4 Bauingenieurwesen ; Nr. 156)
Y1  - 1999
SN  - 3-18-315604-0
SP  - 208
EP  - 215
PB  - VDI-Verlag
CY  - Düsseldorf
ER  - 
TY  - CHAP
A1  - Kuhlmann, Wolfram
A1  - Butenweg, Christoph
A1  - Meskouris, Konstantin
A1  - Kempen, Thomas
T1  - Simulation des Tragverhaltens des Aachener Doms im Erdbebenfall
T2  - Die karolingische Pfalzkapelle in Aachen : Material, Bautechnik, Restaurierung. (Arbeitshefte der rheinischen Denkmalpflege ; 78)
Y1  - 2012
SN  - 978-3-88462-325-1
SP  - 237
EP  - 248
PB  - Wernersche Verlags-Gesellschaft
CY  - Worms
ER  - 
TY  - JOUR
A1  - Kuhlmann, Wolfram
A1  - Butenweg, Christoph
A1  - Meskouris, Konstantin
T1  - Baudynamische Untersuchung des Aachener Doms unter Erdbebenbelastung
JF  - Bautechnik : Zeitschrift für den gesamten Ingenieurbau
Y1  - 2003
U6  - http://dx.doi.org/10.1002/bate.200305080
SN  - 1437-0999 (E-Journal); 0005-6820 (Print); 0932-8351 (Print)
N1  - Als Printausgabe in der Bibliothek Bayernallee vorhanden: 13 Z 177
VL  - Vol. 80
IS  - Iss. 10
SP  - 675
EP  - 684
ER  - 
TY  - CHAP
A1  - Kuhlmann, Wolfram
A1  - Butenweg, Christoph
A1  - Lopez, Marijen
A1  - Fernandez, Sebastian
T1  - Seismic vulnerability assessment of the historic Aachen Cathedral
T2  - Conference proceedings / 13th World Conference on Earthquake Engineering [Vancouver, British Columbia, Canada, August 1 - 6, 2004] / [hosted by CAEE/ACGP, Canadian Association for Earthquake Engineering]
Y1  - 2004
SP  - 1
EP  - 14
PB  - CAEE
CY  - Vancouver
ER  - 
TY  - CHAP
A1  - Kuhlmann, Wolfram
A1  - Butenweg, Christoph
A1  - Bettzieche, Volker
A1  - Meskouris, Konstantin
T1  - Experimentelle und numerische Untersuchungen zur baudynamischen Beurteilung von Talsperren des Ruhrverbandes
T2  - 13. Deutsches Talsperrensymposium in Weimar
Y1  - 2004
SP  - 1
EP  - 26
ER  - 
TY  - JOUR
A1  - Kuhlmann, Wolfram
A1  - Butenweg, Christoph
A1  - Bettzieche, Volker
T1  - Experimentelle und numerische Untersuchungen zur baudynamischen Beurteilung von Talsperren
JF  - Wasserwirtschaft : Hydrologie, Wasserbau, Hydromechanik, Gewässer, Ökologie, Boden
Y1  - 2006
SN  - 0043-0978 (E-Journal); 0043-0978 (Print)
VL  - Band 96
IS  - Heft 5
SP  - 10
EP  - 16
ER  - 
TY  - CHAP
A1  - Kuhlmann, W.
A1  - Bettzieche, V.
A1  - Roesler, F.
A1  - Butenweg, Christoph
A1  - Könke, C.
A1  - Meskouris, Konstantin
T1  - Baudynamische Untersuchung von Talsperren des Ruhrverbandes
T2  - Neubewertung der Erdbebensicherheit von Talsperren in Deutschland : DGEB-Workshop, 28. November 2003 in Potsdam = Assessment of the seismic safety of dams in Germany / organisiert von der Deutschen Gesellschaft für Erdbebeningenieurwesen und Baudynamik. K. Meskouris ... (Hrsg.) (DGEB-Publikation ; Nr. 12)
Y1  - 2005
SN  - 3-930108-08-9
SP  - 37
EP  - 48
PB  - DGEB
CY  - Aachen
ER  - 
TY  - JOUR
A1  - Kubalski, Thomas
A1  - Butenweg, Christoph
A1  - El-Deib, Khaled
ED  - Jesse, Dirk
T1  - Vereinfachte Berücksichtigung der Rahmentragwirkung in Mauerwerksgebäuden
T1  - Simplified consideratioon of framing effects in masonry buildings
JF  - Bautechnik
N2  - Aufgrund der gestiegenen Anforderungen durch höhere Ein-wirkungen aus Wind und Erdbeben ist eine Verbesserung und Optimierung der Berechnungs- und Bemessungsansätze für Mauerwerksbauten erforderlich. Eine bessere Ausnutzung der Tragwerksreserven ist durch die Berücksichtigung der Rah-mentragwirkung mit einer Aktivierung der Deckenscheiben in den Rechenmodellen möglich, die in der Praxis aufgrund der Komplexität der Wand-Decken-Interaktion bislang nicht aus-genutzt wird. Im vorliegenden Aufsatz wird ein vereinfachter Ansatz auf Grundlage der mitwirkenden Plattenbreite von Schubwänden aus Mauerwerk vorgestellt, der die wesentli-chen Einfl ussfaktoren in parametrisierten Tabellen erfasst. Damit steht den Tragwerksplanern ein einfach anwendbares Werkzeug zur Verfügung, um die Rahmentragwirkung in der Mauerwerksbemessung anzusetzen.
N2  - Due to the increased requirements resulting from higher wind and earthquake loads, it is necessary to improve and optimise the calculation and design approaches for masonry structures. An important contribution to a better utilisation of the structural load-bearing reserves is the consideration of the framing ef-fects through the activation of the fl oor slabs in the calculation models, which has not been utilised in practice so far due to the complexity of the wall-slab interaction. The paper presents a simplifi ed approach based on the contributory slab width, which captures the essential infl uencing factors in parameter-ised tables. This provides structural engineers with a simple tool to exploit the frame load-bearing effect in masonry design.
KW  - Rahmentragwirkung
KW  - Mauerwerksgebäude
KW  - Wand-Decken-Interaktion
KW  - Momentenverteilung
KW  - DIN EN 1996
Y1  - 2022
U6  - http://dx.doi.org/10.1002/bate.202200081
SN  - 0932-8351
SN  - 1437-0999
VL  - 99
IS  - 12
SP  - 865
EP  - 928
PB  - Ernst & Sohn
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Kubalski, Thomas
A1  - Butenweg, Christoph
T1  - Modelling strategies for horizontally loaded infill masonry
T1  - Modellierungsansätze für horizontal beanspruchtes Ausfachungsmauerwerk
JF  - Mauerwerk : European journal of masonry
Y1  - 2015
U6  - http://dx.doi.org/10.1002/dama.201500675
VL  - Volume 19
IS  - Issue 5
SP  - 363
EP  - 369
PB  - Wiley
CY  - Weinheim
ER  - 
TY  - CHAP
A1  - Kubalski, T.
A1  - Marinković, Marko
A1  - Butenweg, Christoph
ED  - Modena, Claudio
T1  - Numerical investigation of masonry infilled R.C. frames
T2  - Brick and Block Masonry. Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016
Y1  - 2016
SN  - 9781315374963
SP  - 1219
EP  - 1226
PB  - CRC Press
CY  - Leiden
ER  - 
TY  - CHAP
A1  - Kubalski, T.
A1  - Butenweg, Christoph
A1  - Marinković, Marko
A1  - Klinkel, S.
T1  - Investigation Of The Seismic Behaviour Of Infill Masonry Using Numerical Modelling Approaches
T2  - 16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017
N2  - Masonry is a widely spread construction type which is used all over the world for different types of structures. Due to its simple and cheap construction, it is used as non-structural as well as structural element. In frame structures, such as
reinforced concrete frames, masonry may be used as infill. While the bare frame itself is able to carry the loads when it comes to seismic events, the infilled frame is not able to warp freely due to the constrained movement. This restraint results in a complex interaction between the infill and the surrounding frame, which may lead to severe damage to the infill as well as the surrounding frame. The interaction is studied in different projects and effective approaches for the description of the behavior are still lacking. Experimental programs are usually quite expensive, while numerical models, once validated, do offer an efficient approach for the investigation of the interaction when horizontally loaded. In order to study the numerous parameters influencing the seismic load bearing behavior, numerical models may be used. Therefore, this contribution presents a numerical approach for the simulation of infill masonry in reinforced concrete frames. Both parts, the surrounding frame as well as the infill are represented by micro modelling approaches to correctly take into account the different types of failure. The adopted numerical model describes the inelastic behavior of the system, as indicated by the obtained results of the overall structural response as well as the formation of damage in the infilled wall. Comparison of the numerical and experimental results highlights the valuable contribution of numerical simulations in the study and design of infilled frames. As damage of the infill masonry may occur in-plane due to the interaction as well as out-of-plane due to the low vertical load, both directions of loading are investigated.
Y1  - 2017
N1  - Paper No 3064
SP  - 1
EP  - 11
PB  - Chilean Association on Seismology and Earthquake Engineering (ACHISINA)
ER  - 
TY  - CHAP
A1  - Kubalski, T.
A1  - Butenweg, Christoph
T1  - Ausfachungsmauerwerk unter kombinierter seismischer Beanspruchung
T2  - Erdbeben und bestehende Bauten : 14. D-A-C-H Tagung 20.08. - 21.08.2015, ETH Zürich. (Dokumentation / SIA ; D 0255)
Y1  - 2015
SN  - 978-3-03732-060-0
SP  - 117
EP  - 122
PB  - SGEB
CY  - Zürich
ER  - 
TY  - CHAP
A1  - Konrad, M.
A1  - Chudoba, Rostislav
A1  - Butenweg, Christoph
A1  - Bruckermann, O.
T1  - Textile reinforced concrete. Part II: Multi-level modeling concept
T2  - Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universität Weimar. Ed.: K. Gürlebeck; L. Hempel; C. Könke
Y1  - 2003
SP  - 1
EP  - 11
PB  - IKM
CY  - Weimar
ER  - 
TY  - CHAP
A1  - Kob, Malte
A1  - Gömmel, Andreas
A1  - Butenweg, Christoph
A1  - Niendorf, Thoralf
T1  - Training of a combined model of larynx and vocal folds with data from MRI measurements
T2  - The 5th International Conference on Voice Physiology and Biomechanics: Variations across Cultures and Species, July 12-14, 2006, Tokyo, Japan. Proceedings
Y1  - 2006
SP  - 45
EP  - 46
ER  - 
TY  - CHAP
A1  - Kob, Malte
A1  - Butenweg, Christoph
T1  - A finite element model of the interaction between intra-and extralaryngeal muscles
T2  - International Conference on Voice Physiology and Biomechanics, August 18-20, 2004, Marseille, France
Y1  - 2004
SP  - 1
EP  - 2
ER  - 
TY  - BOOK
A1  - Klinkel, Sven
A1  - Butenweg, Christoph
A1  - Lin, Gao
A1  - Holtschoppen, Britta
T1  - Seismic design of industrial facilities : Proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF) /  Sven Klinkel, Christoph Butenweg, Gao Lin, Britta Holtschoppen Editors
Y1  - 2014
SN  - 978-3-658-02809-1 (Print) ; 978-365-80281-0-7 (E-Book)
U6  - http://dx.doi.org/10.1007/978-3-658-02810-7
PB  - Springer Vieweg
CY  - Wiesbaden
ER  - 
TY  - JOUR
A1  - Klein, Michel
A1  - Butenweg, Christoph
A1  - Klinkel, Sven
T1  - The Influence of Soil-Structure-Interaction on the Fatigue Analysis in the Foundation Design of Onshore Wind Turbines
JF  - Procedia Engineering
Y1  - 2017
U6  - http://dx.doi.org/10.1016/j.proeng.2017.09.325
SN  - 1877-7058
VL  - 199
SP  - 3218
EP  - 3223
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Karvanek, Eva
A1  - Butenweg, Christoph
A1  - Ebenau, Carsten
T1  - Bautechnische Prüfung und Bauüberwachung der Arena „Auf Schalke“
T2  - Berichte der Fachtagung Baustatik - Baupraxis 8 am 21. und 22. März 2002 in Braunschweig / Hrsg. Dieter Dinkler
Y1  - 2002
SN  - 3-926031-95-6
SP  - 237
EP  - 245
PB  - TU Braunschweig, Institut für Statik
CY  - Braunschweig
ER  - 
TY  - CHAP
A1  - Karimi, Iman
A1  - Butenweg, Christoph
A1  - Toll, Britta
T1  - Vulnerability assessment of industrial facilities
T2  - Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping
Y1  - 2005
SN  - 1-905088-00-0
U6  - http://dx.doi.org/10.4203/ccp.81.34
SP  - 34, 73
EP  - 75
PB  - Civil-Comp Press
CY  - Stirling
ER  - 
TY  - CHAP
A1  - Kalker, Ines
A1  - Toll, B.
A1  - Holler, Stefan
A1  - Butenweg, Christoph
A1  - Topping, B. H. V.
A1  - Mota Soares, C. A.
T1  - Capacity analysis of textile retrofitted unreinforced masonry
T2  - Proceedings of the Seventh International Conference on Computational Structures Technology : [Lisbon, Portugal, 7 - 9 September 2004] / ed. by B. H. V. Topping ...
Y1  - 2004
SN  - 0-948749-95-4
U6  - http://dx.doi.org/10.4203/ccp.79.194
SP  - 431
EP  - 432
PB  - Civil-Comp Press
CY  - Stirling
ER  - 
TY  - CHAP
A1  - Kalker, Ines
A1  - Neumann, M.
A1  - Butenweg, Christoph
A1  - Holler, Stefan
T1  - Modelling of textile strengthened masonry
T2  - Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping
Y1  - 2005
SN  - 1-905088-00-0
U6  - http://dx.doi.org/10.4203/ccp.81.184
SP  - 447
EP  - 448
PB  - Civil-Comp Press
CY  - Stirling
ER  - 
TY  - CHAP
A1  - Holtschoppen, Britta
A1  - Cornelissen, Philipp
A1  - Butenweg, Christoph
A1  - Meskouris, Konstantin
T1  - Vereinfachtes Berechnungsverfahren zur Berücksichtigung der Interaktionsschwingung bei flüssigkeitsgefüllten Tankbauwerken unter seismischer Belastung
T2  - Berichte der Fachtagung Baustatik-Baupraxis 11 : am 21. und 22. Februar 2011 an der Universität Innsbruck / Hrsg. Gernot Beer ...
Y1  - 2011
SN  - 978-3-85125-115-9
SP  - 155
EP  - 162
PB  - Inst. für Baustatik, Techn. Univ. Graz
CY  - Graz
ER  - 
TY  - JOUR
A1  - Holtschoppen, Britta
A1  - Butenweg, Christoph
A1  - Meskouris, Konstantin
T1  - Seismic design of non-structural components in industrial facilities
JF  - International journal of engineering under uncertainty
Y1  - 2009
SN  - 0975-4806
VL  - Volume 1
SP  - 1
EP  - 13
ER  - 
TY  - JOUR
A1  - Holtschoppen, B.
A1  - Butenweg, Christoph
A1  - Meskouris, Konstantin
T1  - Erdbebensichere Auslegung von Industrieanlagen
JF  - Der Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik
Y1  - 2009
SN  - 0005-6650
IS  - März
SP  - S9
EP  - S14
PB  - VDI Fachmedien
CY  - Düsseldorf
ER  - 
TY  - JOUR
A1  - Holler, S.
A1  - Butenweg, Christoph
A1  - Noh, S.-Y.
A1  - Meskouris, Konstantin
T1  - Computational model of textile-reinforced concrete structures
JF  - Computers & structures : an international journal
Y1  - 2004
U6  - http://dx.doi.org/10.1016/j.compstruc.2004.03.076
SN  - 1879-2243 (E-Journal); 0045-7949 (Print)
VL  - Volume 82
IS  - Issues 23-26
SP  - 1971
EP  - 1979
ER  - 
TY  - CHAP
A1  - Holler, S.
A1  - Butenweg, Christoph
A1  - Noh, S.-Y.
A1  - Meskouris, Konstantin
T1  - Numerical simulation of textile-reinforced concrete structures
T2  - Proceedings of the Sixth International Conference on Computational Structures Technology : [Prague, Czech Republic, 4 - 6 September 2002] / ed. by B. H. V. Topping and Z. Bittnar. (Civil-Comp Press books on computational engineering)
Y1  - 2002
SN  - 0-948749-83-0
SP  - 287
EP  - 288
PB  - Civil-Comp Press
CY  - Stirling
ER  - 
TY  - CHAP
A1  - Gömmel, Andreas
A1  - Niendorf, Thoralf
A1  - Frauenrath, Tobias
A1  - Otten, Mario
A1  - Butenweg, Christoph
A1  - Kob, Malte
T1  - 3D vocal fold geometry mapping using Magnetic Resonance Imaging
T2  - Fortschritte der Akustik : 36. Deutsche Jahrestagung für Akustik ; 15.-18. März 2010, [Berlin ; DAGA 2010] / DEGA ... Wiss. Ed. Michael Möser ... Band 1
Y1  - 2010
SN  - 978-3-9808659-8-2
SP  - 271
EP  - 272
PB  - Deutsche Gesellschaft für Akustik
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Gömmel, Andreas
A1  - Krämer, Sebastian
A1  - Butenweg, Christoph
A1  - Kob, Malte
T1  - A combined FE and multiple-mass model for numerical simulation of phonatory maneuvers
T2  - Proceedings / Forum Acusticum, Budapest, 29 Aug - 2 Sep, 2005 : [Acoustics: science and technology for knowledge based society and healthy environment] / ed. by: Fülöp Augusztinovicz ...
Y1  - 2005
SN  - 978-963-8241-68-9
SP  - 2759
EP  - 2764
PB  - OPAKFI Tud. Egyesület
CY  - Budapest
ER  - 
TY  - CHAP
A1  - Gömmel, Andreas
A1  - Kob, Malte
A1  - Niendorf, Thoralf
A1  - Butenweg, Christoph
T1  - An approach for numerical calculation of glottal flow during glottal closure
T2  - Proceedings / NAG/DAGA 2009, International Conference on Acoustics : Rotterdam, 23 - 26 March 2009 ; [including the 35th German Annual Conference on Acoustics (DAGA)] / [organisers: Acoustical Society of the Netherlands (NAG); German Acoustical Society (DEGA) ...]. Ed. by Marinus M. Boone
Y1  - 2009
SN  - 978-3-9808659-6-8
SP  - 1722
EP  - 1725
PB  - DEGA
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Gömmel, Andreas
A1  - Frauenrath, Tobias
A1  - Otten, Mario
A1  - Niendorf, Thoralf
A1  - Butenweg, Christoph
ED  - Möser, Michael
ED  - Schulte-Fortkamp, Brgitte
ED  - Ochmann, Martin
T1  - In-vivo measurements of vocal fold geometry using Magnetic Resonance Imaging
T2  - Fortschritte der Akustik - DAGA 2010 36. Jahrestagung für Akustik, 15. bis 18. März 2010 in Berlin
Y1  - 2010
SN  - 978-3-9808659-8-2
PB  - Deutsche Gesellschaft für Akustik
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Gömmel, Andreas
A1  - Butenweg, Christoph
A1  - Kob, Malte
T1  - Towards a complete finite-element model of human phonation: modeling phonatory maneuvers
T2  - 12th Workshop on the Finite Element Method in Biomedical Engineering, Biomechanics and Related Fields : Ulm, Germany, 20 - 21 July 2005 / University of Ulm, Department of Orthodontics ...
Y1  - 2005
SN  - 978-3-9806183-8-0
PB  - Univ., Dep. of Orthodontics
CY  - Ulm
ER  - 
TY  - JOUR
A1  - Gömmel, Andreas
A1  - Butenweg, Christoph
A1  - Bolender, Katrin
A1  - Grunendahl, Arno
T1  - A muscle controlled finite-element model of laryngeal abduction and adduction
JF  - Computer methods in biomechanics and biomedical engineering
Y1  - 2007
SN  - 1476-8259 (E-Journal); 1025-5842 (Print)
VL  - Volume 10
IS  - Issue 5
SP  - 377
EP  - 388
ER  - 
TY  - CHAP
A1  - Gömmel, A.
A1  - Butenweg, Christoph
A1  - Kob, M.
T1  - A fluid-structure interaction model of vocal fold oscillation
T2  - 5th International Workshop on Models and Analysis of Vocal Emissions for Biomedical Applications, MAVEBA 2007
N2  - Since fluid-structure interaction within the finite-element method is state of the art in many engineering fields, this method is used in voice analysis. A quasi two-dimensional model of the vocal folds including the ventricular folds is presented. First results of self-sustained vocal fold oscillation are presented and possibilities as well as limitations are discussed.
KW  - finite element method
KW  - fluid structure interaction
KW  - vocal fold oscillation
Y1  - 2007
SN  - 978-888453674-7
N1  - 5th International Workshop on Models and Analysis of Vocal Emissions for Biomedical Applications, MAVEBA 2007; Florence; Italy; 13 December 2007 through 15 December 2007
SP  - 127
EP  - 128
ER  - 
TY  - CHAP
A1  - Grunendahl, A.
A1  - de Rochefort, E.
A1  - Butenweg, Christoph
T1  - Numerical models for investigating the causes of low back pain due to whole-body vibrations
T2  - 2nd International Conference on Computational Bioengineering : Lisbon, September 14-16 2005. Volume 2.
Y1  - 2005
SN  - 978-972-8469-37-3
SP  - 905
EP  - 914
PB  - IST Press
CY  - Lisbon
ER  - 
TY  - CHAP
A1  - Gkatzogias, Konstantinos
A1  - Veljkoviv, Ana
A1  - Pohoryles, Daniel A.
A1  - Tsionis, Georgios
A1  - Bournas, Dionysios A.
A1  - Crowley, Helen
A1  - Norlén, Hedvig
A1  - Butenweg, Christoph
A1  - Gervasio, Helena
A1  - Manfredi, Vincenzo
A1  - Masi, Angelo
A1  - Zaharieva, Roumiana
ED  - Gkatzogias, Konstantinos
ED  - Tsionis, Georgios
T1  - Policy practice and regional impact assessment for building renovation
T2  - REEBUILD Integrated Techniques for the Seismic Strengthening & Energy Efficiency of Existing Buildings
N2  - The work presented in this report provides scientific support to building renovation policies in the EU by promoting a holistic point of view on the topic. Integrated renovation can be seen as a nexus between European policies on disaster resilience, energy efficiency and circularity in the building sector. An overview of policy measures for the seismic and energy upgrading of buildings across EU Member States identified only a few available measures for combined upgrading. Regulatory framework, financial instruments and digital tools similar to those for energy renovation, together with awareness and training may promote integrated renovation. A framework for regional prioritisation of building renovation was put forward, considering seismic risk, energy efficiency, and socioeconomic vulnerability independently and in an integrated way. Results indicate that prioritisation of building renovation is a multidimensional problem. Depending on priorities, different integrated indicators should be used to inform policies and accomplish the highest relative or most spread impact across different sectors. The framework was further extended to assess the impact of renovation scenarios across the EU with a focus on priority regions. Integrated renovation can provide a risk-proofed, sustainable, and inclusive built environment, presenting an economic benefit in the order of magnitude of the highest benefit among the separate interventions. Furthermore, it presents the unique capability of reducing fatalities and energy consumption at the same time and, depending on the scenario, to a greater extent.
Y1  - 2022
SN  - 978-92-76-60454-9
U6  - http://dx.doi.org/10.2760/883122
SN  - 1831-9424
SP  - 1
EP  - 68
PB  - Publications Office of the European Union
CY  - Luxembourg
ER  - 
TY  - JOUR
A1  - Giresini, Linda
A1  - Sassu, Mauro
A1  - Butenweg, Christoph
A1  - Alecci, Valerio
A1  - De Stefano, Mario
T1  - Vault macro-element with equivalent trusses in global seismic analyses
JF  - Earthquakes and Structures
N2  - This paper proposes a quick and simplified method to describe masonry vaults in global seismic analyses of buildings. An equivalent macro-element constituted by a set of six trusses, two for each transverse, longitudinal and diagonal direction, is introduced. The equivalent trusses, whose stiffness is calculated by fully modeled vaults of different geometry, mechanical properties and boundary conditions, simulate the vault in both global analysis and local analysis, such as kinematic or rocking approaches. A parametric study was carried out to investigate the influence of geometrical characteristics and mechanical features on the equivalent stiffness values. The method was numerically validated by performing modal and transient analysis on a three naves-church in the elastic range. Vibration modes and displacement time-histories were compared showing satisfying agreement between the complete and the simplified models. This procedure is particularly useful in engineering practice because it allows to assess, in a simplified way, the effectiveness of strengthening interventions for reducing horizontal relative displacements between vault supports.
KW  - vault
KW  - macro-element
KW  - equivalent stiffness
KW  - truss
KW  - churches
Y1  - 2017
U6  - http://dx.doi.org/10.12989/eas.2017.12.4.409
SN  - 2092-7614 (Print)
SN  - 2092-7622 (Online)
VL  - 12
IS  - 4
SP  - 409
EP  - 423
PB  - Techno-Press
CY  - Taejŏn
ER  - 
TY  - CHAP
A1  - Giresini, Linda
A1  - Butenweg, Christoph
A1  - Andreini, M.
A1  - De Falco, A.
A1  - Sassu, M.
T1  - Numerical calibration of a macro-element for vaultes system in historic churches
T2  - 9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City
Y1  - 2014
SP  - 1
EP  - 12
ER  - 
TY  - CHAP
A1  - Giresini, Linda
A1  - Butenweg, Christoph
A1  - Andreini, M.
A1  - De Falco, A.
A1  - Sassu, M.
T1  - Macro-elements identification in historic chapels: the case of St. Venerio Chapel in Reggiolo - Emilia Romagna
T2  - 9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City
Y1  - 2014
SP  - 1
EP  - 12
ER  - 
TY  - CHAP
A1  - Giresini, Linda
A1  - Butenweg, Christoph
T1  - Earthquake resistant design of structures according to Eurocode 8
T2  - Structural Dynamics with Applications in Earthquake and Wind Engineering
N2  - The chapter initially provides a summary of the contents of Eurocode 8, its aim being to offer both to the students and to practising engineers an easy introduction into the calculation and dimensioning procedures of this earthquake code. Specifically, the general rules for earthquake-resistant structures, the definition of design response spectra taking behaviour and importance factors into account, the application of linear and non-linear calculation methods and the structural safety verifications at the serviceability and ultimate limit state are presented. The application of linear and non-linear calculation methods and corresponding seismic design rules is demonstrated on practical examples for reinforced concrete, steel and masonry buildings. Furthermore, the seismic assessment of existing buildings is discussed and illustrated on the example of a typical historical masonry building in Italy. The examples are worked out in detail and each step of the design process, from the preliminary analysis to the final design, is explained in detail.
KW  - Seismic design
KW  - Eurocode 8
KW  - Design examples
KW  - Response spectrum
KW  - Pushover analysis
Y1  - 2019
SN  - 978-3-662-57550-5 (Online)
SN  - 978-3-662-57548-2 (Print)
U6  - http://dx.doi.org/10.1007/978-3-662-57550-5_4
SP  - 197
EP  - 358
PB  - Springer
CY  - Berlin
ER  - 
TY  - CHAP
A1  - Gellert, Christoph
A1  - Park, Jin
A1  - Butenweg, Christoph
T1  - Seismic safety verification of masonry structures
T2  - Proceedings of the Eight International Masonry Conference : held in Dresden from 4th to 7th of July 2010 / [International Masonry Society ; Technische Universität Dresden]. Ed. by: Wolfram Jäger ... Volume 1. (Masonry / International Masonry Society Special Publication ; 11)
Y1  - 2010
SN  - 978-3-00-031381-3
SP  - 813
EP  - 822
PB  - ARGE 8IMC Dresden
CY  - Radebeul
ER  - 
TY  - CHAP
A1  - Gellert, Christoph
A1  - Norda, Hannah
A1  - Butenweg, Christoph
T1  - Nonlinear behaviour of masonry under cyclic loading
T2  - 7th European Conference on Structural Dynamics, EURODYN 2008 : 7-9 July 2008, Southampton
Y1  - 2008
SP  - 1
EP  - 12
ER  -