TY - CHAP A1 - Rosin, J. A1 - Mykoniou, K. A1 - Butenweg, Christoph T1 - Analysis Of Base Isolated Liquid Storage Tanks With 3D Fsi-Analysis As Well As Simplified Approaches T2 - 16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017 N2 - Tanks are preferably designed, for cost-saving reasons, as circular, cylindrical, thin-walled shells. In case of seismic excitation, these constructions are highly vulnerable to stability failures. An earthquake-resistant design of rigidly supported tanks for high seismic loading demands, however, uneconomic wall thicknesses. A cost-effective alternative can be provided by base isolation systems. In this paper, a simplified seismic design procedure for base isolated tanks is introduced, by appropriately modifying the standard mechanical model for flexible, rigidly supported tanks. The non-linear behavior of conventional base isolation systems becomes an integral part of a proposed simplified process, which enables the assessment of the reduced hydrodynamic forces acting on the tank walls and the corresponding stress distribution. The impulsive and convective actions of the liquid are taken into account. The validity of this approach is evaluated by employing a non-linear fluid-structure interaction algorithm of finite element method. Special focus is placed on the boundary conditions imposed from the base isolation and the resulting hydrodynamic pressures. Both horizontal and vertical component of ground motion are considered in order to study the principal effects of the base isolation on the pressure distribution of the tank walls. The induced rocking effects associated with elastomeric bearings are discussed. The results manifest that base isolated tanks can be designed for seismic loads by means of the proposed procedure with sufficient accuracy, allowing to dispense with numerically expensive techniques. KW - liquid storage tank KW - seismic isolation KW - elastomeric bearing KW - friction pendulum bearing KW - simplified approach Y1 - 2017 N1 - Paper No 2246 SP - 1 EP - 14 PB - Chilean Association on Seismology and Earthquake Engineering (ACHISINA) ER - TY - CHAP A1 - Kubalski, T. A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Klinkel, S. T1 - Investigation Of The Seismic Behaviour Of Infill Masonry Using Numerical Modelling Approaches T2 - 16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017 N2 - Masonry is a widely spread construction type which is used all over the world for different types of structures. Due to its simple and cheap construction, it is used as non-structural as well as structural element. In frame structures, such as reinforced concrete frames, masonry may be used as infill. While the bare frame itself is able to carry the loads when it comes to seismic events, the infilled frame is not able to warp freely due to the constrained movement. This restraint results in a complex interaction between the infill and the surrounding frame, which may lead to severe damage to the infill as well as the surrounding frame. The interaction is studied in different projects and effective approaches for the description of the behavior are still lacking. Experimental programs are usually quite expensive, while numerical models, once validated, do offer an efficient approach for the investigation of the interaction when horizontally loaded. In order to study the numerous parameters influencing the seismic load bearing behavior, numerical models may be used. Therefore, this contribution presents a numerical approach for the simulation of infill masonry in reinforced concrete frames. Both parts, the surrounding frame as well as the infill are represented by micro modelling approaches to correctly take into account the different types of failure. The adopted numerical model describes the inelastic behavior of the system, as indicated by the obtained results of the overall structural response as well as the formation of damage in the infilled wall. Comparison of the numerical and experimental results highlights the valuable contribution of numerical simulations in the study and design of infilled frames. As damage of the infill masonry may occur in-plane due to the interaction as well as out-of-plane due to the low vertical load, both directions of loading are investigated. Y1 - 2017 N1 - Paper No 3064 SP - 1 EP - 11 PB - Chilean Association on Seismology and Earthquake Engineering (ACHISINA) ER - TY - JOUR A1 - Klein, Michel A1 - Butenweg, Christoph A1 - Klinkel, Sven T1 - The Influence of Soil-Structure-Interaction on the Fatigue Analysis in the Foundation Design of Onshore Wind Turbines JF - Procedia Engineering Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.proeng.2017.09.325 SN - 1877-7058 VL - 199 SP - 3218 EP - 3223 PB - Elsevier CY - Amsterdam ER - TY - BOOK A1 - Labisch, Susanna A1 - Wählisch, Georg T1 - Technisches Zeichnen: Eigenständig lernen und effektiv üben Y1 - 2017 SN - 978-3-658-18312-7 U6 - http://dx.doi.org/10.1007/978-3-658-18313-4 N1 - gedruckt in der Bereichsbibliothek Jülich vorhanden; auch als elektronische Ressource PB - Springer Vieweg CY - Wiesbaden ET - 5. überarbeitete Auflage ER - TY - JOUR A1 - Butenweg, Christoph A1 - Rosin, Julia A1 - Holler, Stefan T1 - Analysis of cylindrical granular material silos under seismic excitation JF - Buildings N2 - Silos generally work as storage structures between supply and demand for various goods, and their structural safety has long been of interest to the civil engineering profession. This is especially true for dynamically loaded silos, e.g., in case of seismic excitation. Particularly thin-walled cylindrical silos are highly vulnerable to seismic induced pressures, which can cause critical buckling phenomena of the silo shell. The analysis of silos can be carried out in two different ways. In the first, the seismic loading is modeled through statically equivalent loads acting on the shell. Alternatively, a time history analysis might be carried out, in which nonlinear phenomena due to the filling as well as the interaction between the shell and the granular material are taken into account. The paper presents a comparison of these approaches. The model used for the nonlinear time history analysis considers the granular material by means of the intergranular strain approach for hypoplasticity theory. The interaction effects between the granular material and the shell is represented by contact elements. Additionally, soil–structure interaction effects are taken into account. KW - granular silo KW - earthquake engineering KW - hypoplasticity KW - nonlinear transient analyses Y1 - 2017 U6 - http://dx.doi.org/10.3390/buildings7030061 SN - 2075-5309 VL - 7 IS - 3 SP - 1 EP - 12 PB - MDPI CY - Basel ER - TY - JOUR A1 - Butenweg, Christoph T1 - Die neue Erdbebenfibel. Neue Hilfsmittel für die Leichtbetonindustrie JF - Tagungsband 61. Ulmer Beton Tage 2017 Y1 - 2017 ER - TY - CHAP A1 - Rajan, S. A1 - Butenweg, Christoph A1 - Dalguer, L. A. A1 - An, J. H. A1 - Renault, P. A1 - Klinkel, S. T1 - Fragility curves for a three-storey reinforced concrete test structure of the international benchmark SMART 2013 T2 - 16th World Conference on Earthquake, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017 Y1 - 2017 N1 - Paper No 2119 PB - Chilean Association on Seismology and Earthquake Engineering (ACHISINA) ER - TY - CHAP A1 - Altherr, Lena A1 - Ederer, Thorsten A1 - Schänzle, Christian A1 - Lorenz, Ulf A1 - Pelz, Peter F. T1 - Algorithmic system design using scaling and affinity laws T2 - Operations Research Proceedings 2015 N2 - Energy-efficient components do not automatically lead to energy-efficient systems. Technical Operations Research (TOR) shifts the focus from the single component to the system as a whole and finds its optimal topology and operating strategy simultaneously. In previous works, we provided a preselected construction kit of suitable components for the algorithm. This approach may give rise to a combinatorial explosion if the preselection cannot be cut down to a reasonable number by human intuition. To reduce the number of discrete decisions, we integrate laws derived from similarity theory into the optimization model. Since the physical characteristics of a production series are similar, it can be described by affinity and scaling laws. Making use of these laws, our construction kit can be modeled more efficiently: Instead of a preselection of components, it now encompasses whole model ranges. This allows us to significantly increase the number of possible set-ups in our model. In this paper, we present how to embed this new formulation into a mixed-integer program and assess the run time via benchmarks. We present our approach on the example of a ventilation system design problem. KW - Optimal Topology KW - Piecewise Linearization KW - Ventilation System KW - Similarity Theory Y1 - 2017 SN - 978-3-319-42901-4 SN - 978-3-319-42902-1 U6 - http://dx.doi.org/10.1007/978-3-319-42902-1 N1 - International Conference of the German, Austrian and Swiss Operations Research Societies (GOR, ÖGOR, SVOR/ASRO), University of Vienna, Austria, September 1-4, 2015 SP - 605 EP - 611 PB - Springer CY - Cham ER - TY - CHAP A1 - Altherr, Lena A1 - Ederer, Thorsten A1 - Farnetane, Lucas S. A1 - Pöttgen, Philipp A1 - Vergé, Angela A1 - Pelz, Peter F. T1 - Multicriterial design of a hydrostatic transmission system via mixed-integer programming T2 - Operations Research Proceedings 2015 N2 - In times of planned obsolescence the demand for sustainability keeps growing. Ideally, a technical system is highly reliable, without failures and down times due to fast wear of single components. At the same time, maintenance should preferably be limited to pre-defined time intervals. Dispersion of load between multiple components can increase a system’s reliability and thus its availability inbetween maintenance points. However, this also results in higher investment costs and additional efforts due to higher complexity. Given a specific load profile and resulting wear of components, it is often unclear which system structure is the optimal one. Technical Operations Research (TOR) finds an optimal structure balancing availability and effort. We present our approach by designing a hydrostatic transmission system. Y1 - 2017 SN - 978-3-319-42901-4 SN - 978-3-319-42902-1 U6 - http://dx.doi.org/10.1007/978-3-319-42902-1_41 N1 - International Conference of the German, Austrian and Swiss Operations Research Societies (GOR, ÖGOR, SVOR/ASRO), University of Vienna, Austria, September 1-4, 2015 SP - 301 EP - 307 PB - Springer CY - Cham ER - TY - CHAP A1 - Steuer-Dankert, Linda A1 - Sharma, Mamta Rameshwarlal A1 - Bleck, Wolfgang A1 - Leicht-Scholten, Carmen ED - Farn, C. K. T1 - Innovation through Diversity - Development of a Diversity and Innovation management concept T2 - International Conference on Innovation and Management : IAM23017S : Date: July 4-7, 2017, Osaka, Japan N2 - Acknowledging that a diverse workforce could be a potential source of innovation, the current research deals with the fine details of why diversity management is central to achieving innovation in heterogeneous research groups and how this could be effectively realized in an organization. The types of heterogeneities addressed mainly include gender, qualification, academic discipline and intercultural perspectives. The type of organization being dealt with in this work is a complex association of research institutes at a technical university in Germany (RWTH Aachen University), namely a 'Cluster of Excellence', whereby several institutes of the university work collaboratively in different sub-projects. The 'Cluster of Excellence' is a part of the 'Excellence Initiative' of the German federal and state governments German Research Foundation (DFG) and German Council of Science and Humanities, with the ultimate aim of promoting cutting-edge research. To support interdisciplinary collaboration and thus the performance of the cluster, the development of a diversity and innovation management concept is presently in the conceptual phase and will be described in the frame of this paper. The 3-S-Diversity Model, composed of the three elements: skills, structure and strategy, serves as a basis for the development of the concept. The proposed concept consists of six phases; the first two phases lay the ground work by developing an understanding of the status quo on the forms of diversity in the Cluster of Excellence, the type of organizational structure of the member institutes and the varieties of specialist work cultures of the same. The third and the fourth phases build up on this foundation by means of qualitative and quantitative studies. While the third phase deals with the sensitization of the management level to the close connection between diversity and innovation; the need to manage them thereafter and find tailor-made methods of doing so, the fourth phase shall mainly focus on the mindset of the employees in this regard. The fifth phase shall consolidate the learnings and the ideas developed in the course of the first four phases into an implementable strategy. The ultimate phase shall be the implementation of this concept in the Cluster. The first three phases have been accomplished successfully and the preliminary results are already available. Y1 - 2017 SN - 2218-6387 SP - Panel C PB - Kuang Hui Chiu CY - Osaka ER - TY - CHAP A1 - Schnejider, Dominik A1 - Wisselink, Frank A1 - Czarnecki, Christian ED - Eibl, Maximilian ED - Gaedke, Martin ED - Gesellschaft für Informatik e. V. (GI), T1 - Transformation von Wertschöpfungsketten durch das Internet der Dinge – Bewertungsrahmen und Fallstudie T2 - GI Edition Proceedings Band 275 INFORMATIK 2017 N2 - Momentan finden in vielen Branchen umfassende Veränderungen von Märkten und Wertschöpfungsketten statt, welche auch als Digitale Transformation bezeichnet werden. In diesem Zusammenhang wird das Internet der Dinge (Internet of Things, IoT) als ein wichtiger technischer Enabler der Veränderungen angesehen. Primäre Ziele des IoT sind die Steuerung physischer Gegen-stände aus der Distanz und das Erfassen von Informationen aus dem Umfeld dieser Gegenstände. Welche neuen Geschäfts-bzw. Partnermodelle entstehen durch die gemeinsame Nutzung von IoT-Daten und Big-Data-Technologien und welcher qualitative Mehrwert wird dadurch geschaffen? Als Antwort wird in diesem Beitrag ein Bewertungsrahmen zur qualitativen Wertschöpfungsanalyse von IoT vorgeschlagen. Anhand dieses Bewertungsrahmens wird ein Anwendungsfall untersucht, der in anonymisierter Form an konkrete Praxisprojekte angelehnt ist. Konkret wird ein Anwendungsfall betrachtet, der eine Abfallwirtschaft 2.0 basierend auf dem Einsatz von IoT vorschlägt. Aus den Untersuchungsergebnissen gehen beispielsweise Erkenntnisse hervor, wie Geschäftsmodelle auf Basis eines unentgeltlichen Informationsaustauschs durch IoT gestaltet werden können. KW - Digitale Transformation KW - Unternehmensarchitekturen KW - Unternehmensarchitekturen Internet der Dinge KW - Geschäftsmodelle KW - Wertschöpfungskettenanalyse Y1 - 2017 SN - 978-3-88579-669-5 U6 - http://dx.doi.org/10.18420/in2017_208 SN - 1617-5468 N1 - Unternehmensarchitektur in Forschung und Praxis, Chemnitz, 25.-29. September 2017 SP - 2081 EP - 2094 PB - Köllen CY - Bonn ER - TY - CHAP A1 - Thomé, Tristan Eberhard A1 - Czarnecki, Christian A1 - Auth, Gunnar A1 - Bensberg, Frank ED - Barton, Thomas ED - Herrmann, Frank ED - Meister, Vera G. ED - Müller, Christian ED - Seel, Christian T1 - Erweiterung des Referenzprozessmodells eTOM um die Anforderungen des deutschen IT-Sicherheitsgesetzes T2 - Prozesse, Technologie, Anwendungen, Systeme und Management 2017. Angewandte Forschung in der Wirtschaftsinformatik N2 - Kritische Infrastrukturen sind primäre Ziele krimineller Hacker. Der Deutsche Bundestag reagierte darauf am 25. Juli 2015 mit einem Gesetz zur Verbesserung der Sicherheit von ITSystemen, dem IT-Sicherheitsgesetz. Dies verlangt von Betreibern kritischer Infrastrukturen, angemessene Mindeststandards für organisatorische und technische Sicherheit zu implementieren, um den Betrieb und die Verfügbarkeit dieser Infrastruktur zu gewährleisten. Telekommunikationsunternehmen sind einerseits von diesem Gesetz in besonderem Maße betroffen und verfügen andererseits mit dem Rahmenwerk enhanced Telecom Operations Map (eTOM) über ein international anerkanntes Referenzmodell zur Gestaltung von Geschäftsprozessen in dieser Branche. Da sämtliche Telekommunikationsunternehmen in Deutschland verpflichtet sind, das Gesetz innerhalb eines bestimmten Zeitrahmens zu implementieren, präsentiert dieser Beitrag einen Vorschlag zur Erweiterung von eTOM um die relevanten Anforderungen des deutschen IT-Sicherheitsgesetzes. Y1 - 2017 SN - 978-3-944330-56-3 N1 - Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg SP - 51 EP - 60 PB - mana-Buch CY - Heide ER - TY - CHAP A1 - Schneider, Dominik A1 - Wisselink, Frank A1 - Czarnecki, Christian ED - Barton, Thomas ED - Herrmann, Frank ED - Meister, Vera G. ED - Müller, Christian ED - Seel, Christian T1 - Qualitative Wertschöpfungsanalyse von Anwendungsfällen des Narrowband Internet of Things T2 - Prozesse, Technologie, Anwendungen, Systeme und Management 2017. Angewandte Forschung in der Wirtschaftsinformatik N2 - Primäre Ziele des Internets der Dinge sind die Steuerung physischer Gegenstände aus der Distanz und das Erfassen von Informationen aus dem Umfeld dieser Gegenstände. Dazu werden Hardwarekomponenten in Gegenstände des täglichen Lebens und die Umwelt integriert. Mithilfe von Informations- und Kommunikationstechnologien entsteht hieraus das Internet der Dinge (Internet of Things, IoT). Vor einem Jahr wurde mit Narrowband Internet of Things (NB-IoT) eine Technologie die es ermöglicht, Hardwarekomponenten energieeffizient und unmittelbar über das Mobilfunknetz zu vernetzen. Gegenstände werden dadurch über große Reichweiten eigenständig kommunikationsfähig. Das IoT steht mit NB-IoT vor einem gestiegenen Nutzenpotenzial, da eine zunehmende Anzahl miteinander verbundener Gegenstände und der Austausch größerer Datenmengen realisierbar sind. Damit sind aus wirtschaftlicher Sicht neue, innovative Anwendungsfälle des IoT möglich, die auch bereits in der Praxis diskutiert werden. In diesem Beitrag wird anhand eines konkreten Anwendungsfalls untersucht, welche neuen Geschäfts- bzw. Partnermodelle durch die gemeinsame Nutzung von NB-IoT-Daten und Big Data-Technologien entstehen und welcher qualitative Mehrwert für die an einem Anwendungsfall beteiligten Stakeholder geschaffen wird. Dazu wird – einem konstruktionsorientierten Forschungsansatz folgend – ein Bewertungsrahmen zur qualitativen Wertschöpfungsanalyse von NB-IoT entwickelt, der u.a. auf der Schablone nach Cockburn und dem Business Model Canvas basiert. Anhand dieses Bewertungsrahmens wird ein Anwendungsfall untersucht, der in anonymisierter Form an konkrete Praxisprojekte angelehnt ist. Konkret wird ein Anwendungsfall betrachtet, der einen Fahrradverleih 2.0 basierend auf dem Einsatz von NB-IoT vorschlägt. Aus den Untersuchungsergebnissen gehen beispielsweise Erkenntnisse hervor, wie Geschäftsmodelle auf Y1 - 2017 SN - 978-3-944330-56-3 N1 - Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg SP - 184 EP - 193 PB - mana-Buch CY - Heide ER - TY - CHAP A1 - Czarnecki, Christian A1 - Dietze, Christian ED - Maedche, Alexander ED - vom Brocke, Jan ED - Hevner, Alan T1 - Domain-Specific reference modeling in the telecommunications industry T2 - DESRIST 2017: Designing the Digital Transformation N2 - The telecommunications industry is currently going through a major transformation. In this context, the enhanced Telecom Operations Map (eTOM) is a domain-specific process reference model that is offered by the industry organization TM Forum. In practice, eTOM is well accepted and confirmed as de facto standard. It provides process definitions and process flows on different levels of detail. This article discusses the reference modeling of eTOM, i.e., the design, the resulting artifact, and its evaluation based on three project cases. The application of eTOM in three projects illustrates the design approach and concrete models on strategic and operational levels. The article follows the Design Science Research (DSR) paradigm. It contributes with concrete design artifacts to the transformational needs of the telecommunications industry and offers lessons-learned from a general DSR perspective. KW - enhanced Telecom Operations Map (eTOM) KW - Process reference model KW - Process design KW - Map (eTOM) Process reference model Process design Telecommunications industry Y1 - 2017 SN - 978-3-319-59144-5 SN - 978-3-319-59143-8 U6 - http://dx.doi.org/10.1007/978-3-319-59144-5_19 N1 - Designing the Digital Transformation 12th International Conference, DESRIST 2017, Karlsruhe, Germany, May 30 - June 1, 2017. SP - 313 EP - 329 PB - Springer CY - Cham ER - TY - BOOK A1 - Czarnecki, Christian A1 - Dietze, Christian T1 - Reference architecture for the telecommunications industry: Transformation of strategy, organization, processes, data, and applications N2 - This book reflects the tremendous changes in the telecommunications industry in the course of the past few decades – shorter innovation cycles, stiffer competition and new communication products. It analyzes the transformation of processes, applications and network technologies that are now expected to take place under enormous time pressure. The International Telecommunication Union (ITU) and the TM Forum have provided reference solutions that are broadly recognized and used throughout the value chain of the telecommunications industry, and which can be considered the de facto standard. The book describes how these reference solutions can be used in a practical context: it presents the latest insights into their development, highlights lessons learned from numerous international projects and combines them with well-founded research results in enterprise architecture management and reference modeling. The complete architectural transformation is explained, from the planning and set-up stage to the implementation. Featuring a wealth of examples and illustrations, the book offers a valuable resource for telecommunication professionals, enterprise architects and project managers alike. KW - Enterprise architecture KW - Enterprise transformation KW - Reference modelling KW - TM Forum KW - Telecommunication Y1 - 2017 SN - 978-3-319-46755-9 (Print) SN - 978-3-319-83578-5 (Print) SN - 978-3-319-46757-3 (PDF) U6 - http://dx.doi.org/10.1007/978-3-319-46757-3 PB - Springer CY - Cham ER - TY - JOUR A1 - Czarnecki, Christian A1 - Geier, Jari A1 - Pflug, Karolin T1 - Netzvirtualisierung durch SDN und NFV : Unternehmensprozesse auf dem Prüfstand JF - LANline N2 - Kundenanforderungen an Netzwerke haben sich in den vergangenen Jahren stark verändert. Mit NFV und SDN sind Unternehmen technisch in der Lage, diesen gerecht zu werden. Die Provider stehen jedoch vor großen Herausforderungen: Insbesondere Produkte und Prozesse müssen angepasst und agiler werden, um die Stärken von NFV und SDN zum Kundenvorteil auszuspielen. Y1 - 2017 SN - 0942-4172 PB - AWI Aktuelles Wissen Verl.-Ges. CY - Trostberg ER - TY - CHAP A1 - Funke, Harald A1 - Beckmann, Nils A1 - Abanteriba, Sylvester T1 - A comparison of complex chemistry mechanisms for hydrogen methane blends based on the Sandia / Sydney Bluff-Body Flame HM1 T2 - Proceedings of the Eleventh Asia‐Pacific Conference on Combustion (ASPACC 2017), New South Wales, Australia, 10-14 December 2017 Y1 - 2017 SN - 978-1-5108-5646-2 SP - 262 EP - 265 ER - TY - JOUR A1 - Weber, Tobias A1 - Ruff-Stahl, Hans-Joachim K. T1 - Advances in Composite Manufacturing of Helicopter Parts JF - International Journal of Aviation, Aeronautics, and Aerospace Y1 - 2017 U6 - http://dx.doi.org/10.15394/ijaaa.2017.1153 SN - 2374-6793 VL - 4 IS - 1 ER - TY - JOUR A1 - Weber, Tobias A1 - Arent, Jan-Christoph A1 - Steffen, Lucas A1 - Balvers, Johannes M. A1 - Duhovic, Miro T1 - Thermal optimization of composite autoclave molds using the shift factor approach for boundary condition estimation JF - Journal of Composite Materials Y1 - 2017 U6 - http://dx.doi.org/10.1177/0021998317699868 SN - 1530-793X VL - 51 IS - 12 SP - 1753 EP - 1767 PB - Sage CY - London ER - TY - CHAP A1 - Ayed, Anis Haj A1 - Striegan, Constantin J. D. A1 - Kusterer, Karsten A1 - Funke, Harald A1 - Kazari, M. A1 - Horikawa, Atsushi A1 - Okada, Kunio T1 - Automated design space exploration of the hydrogen fueled "Micromix" combustor technology N2 - Combined with the use of renewable energy sources for its production, Hydrogen represents a possible alternative gas turbine fuel for future low emission power generation. Due to its different physical properties compared to other fuels such as natural gas, well established gas turbine combustion systems cannot be directly applied for Dry Low NOx (DLN) Hydrogen combustion. This makes the development of new combustion technologies an essential and challenging task for the future of hydrogen fueled gas turbines. The newly developed and successfully tested “DLN Micromix” combustion technology offers a great potential to burn hydrogen in gas turbines at very low NOx emissions. Aiming to further develop an existing burner design in terms of increased energy density, a redesign is required in order to stabilise the flames at higher mass flows and to maintain low emission levels. For this purpose, a systematic design exploration has been carried out with the support of CFD and optimisation tools to identify the interactions of geometrical and design parameters on the combustor performance. Aerodynamic effects as well as flame and emission formation are observed and understood time- and cost-efficiently. Correlations between single geometric values, the pressure drop of the burner and NOx production have been identified as a result. This numeric methodology helps to reduce the effort of manufacturing and testing to few designs for single validation campaigns, in order to confirm the flame stability and NOx emissions in a wider operating condition field. Y1 - 2017 N1 - Proceedings of the 1st Global Power and Propulsion Forum GPPF 2017, Jan 16-18, 2017, Zurich, Switzerland SP - 1 EP - 8 ER - TY - JOUR A1 - Ayed, Anis Haj A1 - Kusterer, Karsten A1 - Funke, Harald A1 - Keinz, Jan A1 - Bohn, D. T1 - CFD based exploration of the dry-low-NOx hydrogen micromix combustion technology at increased energy densities JF - Propulsion and Power Research KW - Micromix combustion KW - Hydrogen gas turbine KW - Hydrogen combustion KW - High hydrogen combustion KW - Dry-low-NOx (DLN) combustion Y1 - 2017 SN - 2212-540X U6 - http://dx.doi.org/10.1016/j.jppr.2017.01.005 VL - 6 IS - 1 SP - 15 EP - 24 PB - Elsevier CY - Amsterdam ER - TY - RPRT A1 - Digel, Ilya A1 - Kayser, Peter T1 - VirEx - Eliminierung von Quarantäne relevanten Viroiden aus Kulturpflanzen Abschlussbericht des Projektes KMU-innovativ-12: Teilprojekt 3 Y1 - 2017 U6 - http://dx.doi.org/10.2314/GBV:1012136345 N1 - Druck-Ausgabe: Schlussbericht für das BMBF-Forschungsvorhaben "VirEx - Eliminierung von Quarantäne relevanten Viroiden aus Kulturpflanzen" Förderkennzeichen BMBF 031A400C PB - Institut für Bioengineering (IfB) der FH Aachen CY - Aachen ER - TY - CHAP A1 - Grundmann, Jan Thimo A1 - Boden, Ralf A1 - Ceriotti, Matteo A1 - Dachwald, Bernd A1 - Dumont, Etienne A1 - Grimm, Christian D. A1 - Lange, Caroline A1 - Lichtenheldt, Roy A1 - Pelivan, Ivanka A1 - Peloni, Alessandro A1 - Riemann, Johannes A1 - Spröwitz, Tom A1 - Tardivel, Simon T1 - Soil to sail-asteroid landers on near-term sailcraft as an evolution of the GOSSAMER small spacecraft solar sail concept for in-situ characterization T2 - 5th IAA Planetary Defense Conference KW - multiple NEA rendezvous KW - solar sail KW - GOSSAMER-1 KW - MASCOT KW - asteroid sample return Y1 - 2017 N1 - 5th IAA Planetary Defense Conference – PDC 2017 15-19 May 2017, Tokyo, Japan ER - TY - CHAP A1 - Dachwald, Bernd T1 - Radiation pressure force model for an ideal laser-enhanced solar sail T2 - 4th International Symposium on Solar Sailing N2 - The concept of a laser-enhanced solar sail is introduced and the radiation pressure force model for an ideal laser-enhanced solar sail is derived. A laser-enhanced solar sail is a “traditional” solar sail that is, however, not solely propelled by solar radiation, but additionally by a laser beam that illuminates the sail. The additional laser radiation pressure increases the sail's propulsive force and can give, depending on the location of the laser source, more control authority over the direction of the solar sail’s propulsive force vector. This way, laser-enhanced solar sails may augment already existing solar sail mission concepts and make novel mission concepts feasible. Y1 - 2017 N1 - 4th International Symposium on Solar Sailing 17-20 January 2017, Kyōto, Japan SP - 1 EP - 5 ER - TY - JOUR A1 - Golland, Alexander A1 - Kriegesmann, Torben ED - Härting, Niko T1 - Der Schutz virtueller Identitäten durch die DSGVO JF - PinG Privacy in Germany N2 - Die Frage des Schutzes von virtuellen Identitäten ist – insbesondere bei Online-Medien – von elementarer Bedeutung: Ihre Beantwortung entscheidet über die Anwendbarkeit des Datenschutzrechts auf vermeintlich anonyme Nutzerprofile im Internet. Eine differenzierte Auseinandersetzung mit der Problematik, ob und unter welchen Umständen virtuelle Identitäten dem Datenschutzrecht unterfallen, fehlt bislang. Der vorliegende Beitrag gibt einen Überblick über den Schutz virtueller Identitäten und zeigt Ansätze auf, mittels derer bestimmt werden kann, wann virtuelle Identitäten nach Inkrafttreten der DSGVO durch das Datenschutzrecht geschützt werden. Y1 - 2017 SN - 2197-1862 U6 - http://dx.doi.org/10.37307/j.2196-9817.2017.02.03 VL - 5 IS - 2 SP - 45 EP - 50 PB - Erich Schmidt Verlag CY - Berlin ER - TY - CHAP A1 - Butenweg, Christoph A1 - Marinković, Marko A1 - Kubalski, Thomas A1 - Fehling, Ekkehard A1 - Pfetzing, Thomas A1 - Meyer, Udo ED - Zabel, Volkmar ED - Beinersdorf, Silke T1 - Innovative Ansätze für die seismische Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk T2 - Vortragsband der 15. D-A-CH-Tagung Erdbebeningenieurwesen und Baudynamik KW - Stahlbetonrahmen KW - Ausfachungsmauerwerk KW - INSYSME KW - Erdbeben KW - Ziegelmauerwerk Y1 - 2017 SN - 978-3-930108-13-5 SP - 130 EP - 145 PB - Deutsche Gesellschaft für Erdbebeningenieurwesen und Baudynamik (DGEB) e.V. CY - Weimar ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - On Hotelling’s T² test in a special paired sample case JF - Communications in Statistics - Theory and Methods N2 - In a special paired sample case, Hotelling’s T² test based on the differences of the paired random vectors is the likelihood ratio test for testing the hypothesis that the paired random vectors have the same mean; with respect to a special group of affine linear transformations it is the uniformly most powerful invariant test for the general alternative of a difference in mean. We present an elementary straightforward proof of this result. The likelihood ratio test for testing the hypothesis that the covariance structure is of the assumed special form is derived and discussed. Applications to real data are given. KW - complete block symmetry KW - Hotelling’s T² test KW - likelihood ratio test KW - uniformly most powerful invariant test Y1 - 2017 U6 - http://dx.doi.org/10.1080/03610926.2017.1408828 SN - 1532-415X VL - 48 IS - 2 SP - 257 EP - 267 PB - Taylor & Francis CY - London ER - TY - JOUR A1 - Baringhaus, Ludwig A1 - Gaigall, Daniel T1 - Hotelling’s T² tests in paired and independent survey samples: An efficiency comparison JF - Journal of Multivariate Analysis N2 - Hotelling’s T² tests in paired and independent survey samples are compared using the traditional asymptotic efficiency concepts of Hodges–Lehmann, Bahadur and Pitman, as well as through criteria based on the volumes of corresponding confidence regions. Conditions characterizing the superiority of a procedure are given in terms of population canonical correlation type coefficients. Statistical tests for checking these conditions are developed. Test statistics based on the eigenvalues of a symmetrized sample cross-covariance matrix are suggested, as well as test statistics based on sample canonical correlation type coefficients. Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.jmva.2016.11.004 SN - 0047-259X VL - 2017 IS - 154 SP - 177 EP - 198 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Rajan, Sreelakshmy A1 - Kubalski, Thomas A1 - Altay, Okyay A1 - Dalguer, Luis A A1 - Butenweg, Christoph T1 - Multi-dimensional fragility analysis of a RC building with components using response surface method T2 - 24th International Conference on Structural Mechanics in Reactor Technology, Busan, Korea, 20-25 August, 2017 N2 - Conventional fragility curves describe the vulnerability of the main structure under external hazards. However, in complex structures such as nuclear power plants, the safety or the risk depends also on the components associated with a system. The classical fault tree analysis gives an overall view of the failure and contains several subsystems to the main event, however, the interactions in the subsystems are not well represented. In order to represent the interaction of the components, a method suggested by Cimellaro et al. (2006) using multidimensional performance limit state functions to obtain the system fragility curves is adopted. This approach gives the possibility of deriving the cumulative fragility taking into account the interaction of the response of different components. In this paper, this approach is used to evaluate seismic risk of a representative electrical building infrastructure, including the component, of a nuclear power plant. A simplified model of the structure, with nonlinear material behavior is employed for the analysis in Abaqus©. The input variables considered are the material parameters, boundary conditions and the seismic input. The variability of the seismic input is obtained from selected ground motion time histories of spectrum compatible synthetic ccelerograms. Unlike the usual Monte Carlo methods used for the probabilistic analysis of the structure, a computationally effective response surface method is used. This method reduces the computational effort of the calculations by reducing the required number of samples. Y1 - 2017 SN - 9781510856776 SP - 3126 EP - 3135 PB - International Assn for Structural Mechanics in Reactor Technology (IASMiRT) CY - Raleigh, USA ER - TY - CHAP A1 - Boesen, Niklas A1 - Rosin, Julia A1 - Butenweg, Christoph A1 - Deichsel, Anne A1 - Klinkel, Sven ED - Zabel, Volkmar ED - Beinersdorf, Silke T1 - Untersuchung vorhandenerTragreserven moderner unbewehrter Mauerwerksbauten T2 - Vortragsband der 15. D-A-CH-Tagung Erdbebeningenieurwesen und Baudynamik Y1 - 2017 SN - 978-3-930108-13-5 N1 - 21.-22. September 2017, Weimar. ISBN laut DNB falsch SP - 408 EP - 418 PB - Deutsche Gesellschaft für Erdbebeningenieurwesen und Baudynamik (DGEB) e.V. CY - Weimar ER - TY - RPRT A1 - Albracht, Kirsten A1 - Ritzmann, Ramona A1 - Kramer, Andreas A1 - Meskemper, Joshua A1 - Stäudle, Benjamin A1 - Kümmel, Jacob A1 - Freyler, Katrin A1 - Felsenberg, Dieter A1 - Gruber, Marksu A1 - Gollhofer, Albert A1 - Belavy, Daniel T1 - Vorhaben: Muskelkraftgenerierungsfähigkeit in Mikrogravitation KW - Elektromyographie KW - Bein KW - Extensor KW - Elektrostimulation KW - Raumfahrt Y1 - 2017 U6 - http://dx.doi.org/10.2314/KXP:1670327353 N1 - Förderkennzeichen: BMWi 50WB1428 Öffentlicher Schlussbericht für die Technische Informationsbibliothek der Universität Hannover Berichtszeitraum: 01.09.2014 - 31.01.2017 PB - Deutsche Sporthochschule Köln CY - Klön ER - TY - JOUR A1 - Giresini, Linda A1 - Sassu, Mauro A1 - Butenweg, Christoph A1 - Alecci, Valerio A1 - De Stefano, Mario T1 - Vault macro-element with equivalent trusses in global seismic analyses JF - Earthquakes and Structures N2 - This paper proposes a quick and simplified method to describe masonry vaults in global seismic analyses of buildings. An equivalent macro-element constituted by a set of six trusses, two for each transverse, longitudinal and diagonal direction, is introduced. The equivalent trusses, whose stiffness is calculated by fully modeled vaults of different geometry, mechanical properties and boundary conditions, simulate the vault in both global analysis and local analysis, such as kinematic or rocking approaches. A parametric study was carried out to investigate the influence of geometrical characteristics and mechanical features on the equivalent stiffness values. The method was numerically validated by performing modal and transient analysis on a three naves-church in the elastic range. Vibration modes and displacement time-histories were compared showing satisfying agreement between the complete and the simplified models. This procedure is particularly useful in engineering practice because it allows to assess, in a simplified way, the effectiveness of strengthening interventions for reducing horizontal relative displacements between vault supports. KW - vault KW - macro-element KW - equivalent stiffness KW - truss KW - churches Y1 - 2017 U6 - http://dx.doi.org/10.12989/eas.2017.12.4.409 SN - 2092-7614 (Print) SN - 2092-7622 (Online) VL - 12 IS - 4 SP - 409 EP - 423 PB - Techno-Press CY - Taejŏn ER - TY - CHAP A1 - Kreyer, Jörg A1 - Esch, Thomas T1 - Simulation Tool for Predictive Control Strategies for an ORCSystem in Heavy Duty Vehicles T2 - European GT Conference 2017 N2 - Scientific questions - How can a non-stationary heat offering in the commercial vehicle be used to reduce fuel consumption? - Which potentials offer route and environmental information among with predicted speed and load trajectories to increase the efficiency of a ORC-System? Methods - Desktop bound holistic simulation model for a heavy duty truck incl. an ORC System - Prediction of massflows, temperatures and mixture quality (AFR) of exhaust gas Y1 - 2017 N1 - European GT Conference 2017, 9.-10. Oktober 2017, Frankfurt a.M. ER - TY - CHAP A1 - Galdi, Chiara A1 - Hartung, Frank A1 - Dugelay, Jean-Luc T1 - Videos versus still images: Asymmetric sensor pattern noise comparison on mobile phones T2 - Electronic Imaging N2 - Nowadays, the most employed devices for recoding videos or capturing images are undoubtedly the smartphones. Our work investigates the application of source camera identification on mobile phones. We present a dataset entirely collected by mobile phones. The dataset contains both still images and videos collected by 67 different smartphones. Part of the images consists in photos of uniform backgrounds, especially collected for the computation of the RSPN. Identifying the source camera given a video is particularly challenging due to the strong video compression. The experiments reported in this paper, show the large variation in performance when testing an highly accurate technique on still images and videos. KW - Image Forensics KW - Mobile Phones KW - Image Database Y1 - 2017 U6 - http://dx.doi.org/10.2352/ISSN.2470-1173.2017.7.MWSF-331 SN - 2470-1173 N1 - IS&T International Symposium on Electronic Imaging 2017 Media Watermarking, Security, and Forensics 2017 SP - 100 EP - 103 PB - Society for Imaging Science and Technology CY - Springfield, Virginia ER -