TY  - JOUR
A1  - Staat, Manfred
T1  - Cyclic plastic deformation tests to verify FEM-based shakedown analyses
N2  - Fatigue analyses are conducted with the aim of verifying that thermal ratcheting is limited. To this end it is important to make a clear distintion between the shakedown range and the ratcheting range (continuing deformation). As part of an EU-supported research project, experiments were carried out using a 4-bar model. The experiment comprised a water-cooled internal tube, and three insulated heatable outer test bars. The system was subjected to alternating axial forces, superimposed with alternating temperatures at the outer bars. The test parameters were partly selected on the basis of previous shakedown analyses. During the test, temperatures and strains were measured as a function of time. The loads and the resulting stresses were confirmed on an ongoing basis during performance of the test, and after it. Different material models were applied for this incremental elasto-plastic analysis using the ANSYS program. The results of the simulation are used to verify the FEM-based shakedown analysis.
KW  - Materialermüdung
KW  - Einspielen <Werkstoff>
KW  - Materialermüdung
KW  - shakedown analyses
KW  - thermal ratcheting
KW  - fatigue analyses
Y1  - 2001
ER  - 
TY  - JOUR
A1  - Staat, Manfred
T1  - Local and global collapse pressure of longitudinally flawed pipes and cylindrical vessels
N2  - Limit loads can be calculated with the finite element method (FEM) for any component, defect geometry, and loading. FEM suggests that published long crack limit formulae for axial defects under-estimate the burst pressure for internal surface defects in thick pipes while limit loads are not conservative for deep cracks and for pressure loaded crack-faces. Very deep cracks have a residual strength, which is modelled by a global collapse load. These observations are combined to derive new analytical local and global collapse loads. The global collapse loads are close to FEM limit analyses for all crack dimensions.
KW  - Finite-Elemente-Methode
KW  - Grenzwertberechnung
KW  - Axialbelastung
KW  - FEM
KW  - Grenzwertberechnung
KW  - Axialbelastung
KW  - Traglastanalyse
KW  - Limit analysis
KW  - Global and local collapse
KW  - Axially cracked pipe
KW  - Pressure loaded crack-face
Y1  - 2005
ER  - 
TY  - JOUR
A1  - Staat, Manfred
T1  - Direct finite element route for design-by-analysis of pressure components
N2  - In the new European standard for unfired pressure vessels, EN 13445-3, there are two approaches for carrying out a Design-by-Analysis that cover both the stress categorization method (Annex C) and the direct route method (Annex B) for a check against global plastic deformation and against progressive plastic deformation. This paper presents the direct route in the language of limit and shakedown analysis. This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for mechanical and thermal actions. One observation from the examples is that the so-called 3f (3Sm) criterion fails to be a reliable check against progressive plastic deformation. Precise conditions are given, which greatly restrict the applicability of the 3f criterion.
KW  - Einspielen <Werkstoff>
KW  - Plastizität
KW  - Deformation
KW  - Analytischer Zulaessigkeitsnachweis
KW  - Einspiel-Analyse
KW  - fortschreitende plastische Deformation
KW  - alternierend Verformbarkeit
KW  - Einspiel-Kriterium
KW  - Design-by-analysis
KW  - Shakedown analysis
KW  - Progressive plastic deformation
KW  - Alternating plasticity
KW  - Shakedown criterion
Y1  - 2005
ER  - 
TY  - JOUR
A1  - Staat, Manfred
T1  - Shakedown and ratchetting under tension-torsion loadings: analysis and experiments
N2  - Structural design analyses are conducted with the aim of verifying the exclusion of ratchetting. To this end it is important to make a clear distinction between the shakedown range and the ratchetting range. The performed experiment comprised a hollow tension specimen which was subjected to alternating axial forces, superimposed with constant moments. First, a series of uniaxial tests has been carried out in order to calibrate a bounded kinematic hardening rule. The load parameters have been selected on the basis of previous shakedown analyses with the PERMAS code using a kinematic hardening material model. It is shown that this shakedown analysis gives reasonable agreement between the experimental and the numerical results. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis.
KW  - Einspielen <Werkstoff>
KW  - Einspielen
KW  - Ratchetting
KW  - Zug-Druck Belastung
KW  - shakedown
KW  - ratchetting
KW  - tension–torsion loading
Y1  - 2003
ER  - 
TY  - JOUR
A1  - Staat, Manfred
T1  - Basis Reduction for the Shakedown Problem for Bounded Kinematic Hardening Material
N2  - Limit and shakedown analysis are effective methods for assessing the load carrying capacity of a given structure. The elasto–plastic behavior of the structure subjected to loads varying in a given load domain is characterized by the shakedown load factor, defined as the maximum factor which satisfies the sufficient conditions stated in the corresponding static shakedown theorem. The finite element dicretization of the problem may lead to very large convex optimization. For the effective solution a basis reduction method has been developed that makes use of the special problem structure for perfectly plastic material. The paper proposes a modified basis reduction method for direct application to the two-surface plasticity model of bounded kinematic hardening material. The considered numerical examples show an enlargement of the load carrying capacity due to bounded hardening.
KW  - Finite-Elemente-Methode
KW  - Einspielen <Werkstoff>
KW  - Basis Reduktion
KW  - konvexe Optimierung
KW  - FEM
KW  - Druckgeräte
KW  - Basis reduction
KW  - Convex optimization
KW  - FEM
KW  - Shakedown analysis
Y1  - 2000
ER  - 
TY  - CHAP
A1  - Staat, Manfred
T1  - Design by Analysis of Pressure Components by non-linear Optimization
N2  - This paper presents the direct route to Design by Analysis (DBA) of the new European pressure vessel standard in the language of limit and shakedown analysis (LISA). This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for some examples from the DBA-Manual. One observation from the examples is, that the optimisation approach gives reliable and close lower bound solutions leading to simple and optimised design decision.
KW  - Analytischer Zulaessigkeitsnachweis
KW  - FEM
KW  - Einspiel-Analyse
KW  - design-by-analysis
KW  - finite element analysis
KW  - limit and shakedown analysis
Y1  - 2003
ER  - 
TY  - JOUR
A1  - Staat, Manfred
T1  - LISA - a European project for FEM-based limit and shakedown analysis
N2  - The load-carrying capacity or the safety against plastic limit states are the central questions in the design of structures and passive components in the apparatus engineering. A precise answer is most simply given by limit and shakedown analysis. These methods can be based on static and kinematic theorems for lower and upper bound analysis. Both may be formulated as optimization problems for finite element discretizations of structures. The problems of large-scale analysis and the extension towards realistic material modelling will be solved in a European research project. Limit and shakedown analyses are briefly demonstrated with illustrative examples.
KW  - Einspielen <Werkstoff>
KW  - Traglast
KW  - Finite-Elemente-Methode
KW  - Traglastanalyse
KW  - Einspielanalyse
KW  - FEM
KW  - limit analysis
KW  - shakedown analysis
Y1  - 2001
ER  - 
TY  - JOUR
A1  - Staat, Manfred
T1  - Direct FEM Limit and Shakedown Analysis with Uncertain Data
N2  - The structural reliability with respect to plastic collapse or to inadaptation is formulated on the basis of the lower bound limit and shakedown theorems. A direct definition of the limit state function is achieved which permits the use of the highly effective first order reliability methods (FORM) is achieved. The theorems are implemented into a general purpose FEM program in a way capable of large-scale analysis. The limit state function and its gradient are obtained from a mathematical optimization problem. This direct approach reduces considerably the necessary knowledge of uncertain technological input data, the computing time, and the numerical error, leading to highly effective and precise reliability analyses.
KW  - Finite-Elemente-Methode
KW  - Einspielen <Werkstoff>
KW  - FEM
KW  - Einspielanalyse
KW  - shakedown
KW  - limit load
KW  - reliability analysis
KW  - FEM
KW  - direct method
Y1  - 2000
ER  - 
TY  - GEN
A1  - Staat, Manfred
T1  - Engineering Mechanics. Lecture Notes. 2nd edition, translation of the 3rd corrected and extended German edition of "Technische Mechanik"
N2  - English translation of the corrected lectures notes of Sebastian Krämer. Contents 0 Introduction to Mechanics 1 Statics of Rigid Bodies 2 Elastostatics (Strength of Materials) 3 Kinematics 4 Kinetics Literature
KW  - Technische Mechanik
KW  - Mechanics
KW  - Statics
KW  - Elastostatics
KW  - Kinematics
KW  - Kinetics
Y1  - 2006
ER  - 
TY  - CHAP
A1  - Staat, Manfred
T1  - Problems and chances for probabilistic fracture mechanics in the analysis of steel pressure boundary reliability. - Überarb. Ausg.
N2  - In: Technical feasibility and reliability of passive safety systems for nuclear power plants. Proceedings of an Advisory Group Meeting held in Jülich, 21-24 November 1994. - Vienna , 1996. - Seite: 43 - 55 IAEA-TECDOC-920 Abstract: It is shown that the difficulty for probabilistic fracture mechanics (PFM) is the general problem of the high reliability of a small population. There is no way around the problem as yet. Therefore what PFM can contribute to the reliability of steel pressure boundaries is demon­strated with the example of a typical reactor pressure vessel and critically discussed. Although no method is distinguishable that could give exact failure probabilities, PFM has several addi­tional chances. Upper limits for failure probability may be obtained together with trends for design and operating conditions. Further, PFM can identify the most sensitive parameters, improved control of which would increase reliability. Thus PFM should play a vital role in the analysis of steel pressure boundaries despite all shortcomings.
KW  - Bruchmechanik
KW  - probabilistic fracture mechanics
KW  - PFM
Y1  - 2006
ER  - 
TY  - JOUR
A1  - Staat, Manfred
T1  - Limit and shakedown analysis under uncertainty
JF  - Tap chi Khoa hoc & ung dung - Dai hoc Ton Duc Thang
Y1  - 2012
N1  - = Journal of Applied Sciences - Ton Duc Thang University
VL  - 19
SP  - 45
EP  - 47
ER  - 
TY  - CHAP
A1  - Srivastava, Alok
A1  - Singh, Virendra
A1  - Dhand, Chetna
A1  - Kaur, Manindar
A1  - Singh, Tejvir
A1  - Witte, Katrin
A1  - Scherer, Ulrich W.
T1  - Study of swift heavy ion modified conduction polymer composites for application as gas sensor
N2  - A polyaniline-based conducting composite was prepared by oxidative polymerisation of aniline in a polyvinylchloride (PVC) matrix. The coherent free standing thin films of the composite were prepared by a solution casting method. The polyvinyl chloride-polyaniline composites exposed to 120 MeV ions of silicon with total ion fluence ranging from 1011 to 1013 ions/cm2, were observed to be more sensitive towards ammonia gas than the unirradiated composite. The response time of the irradiated composites was observed to be comparably shorter. We report for the first time the application of swift heavy ion modified insulating polymer conducting polymer (IPCP) composites for sensing of ammonia gas.
KW  - Biosensor
KW  - Conducing polymer
KW  - ammonia gas sensors
KW  - swift heavy ions
KW  - polymer composites
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1345
ER  - 
TY  - PAT
A1  - Sponagel, Stefan
A1  - Wachowitz, Waldemar
T1  - Shaft seal : United States Patent 5,143,385 ; date of patent: Sep. 1, 1992 / assignee: Firma Carl Freudenberg
Y1  - 1992
N1  - Barcode: US005143385A ; Volltext über Datenbank: http://www.google.com/patents
PB  - [United States Patent and Trademark Office]
CY  - [Alexandria, VA]
ER  - 
TY  - JOUR
A1  - Sponagel, Stefan
A1  - Kilthau, G.
A1  - Spies, K. H.
T1  - Sealing mechanism of lip seals
JF  - Eleventh 11th International Conference on Fluid Sealing : proceedings of the 11th Internat. Conference on Fluid Sealing, held at Cannes, France 8 - 10 April, 1987 / organised and sponsored by BHRA, the Fluid Engineering Centre. Ed. B. S. Nau
Y1  - 1987
SN  - 3-540-51383-3
N1  - International Conference on Fluid Sealing <11, 1987, Cannes>
SP  - 748
EP  - 772
PB  - Elsevier
CY  - London
ER  - 
TY  - PAT
A1  - Sponagel, Stefan
A1  - Graf, Günter
A1  - Groß, Heinz
T1  - Method for manufacturing a sealing ring : United States Patent 4,861,536 ; date of patent: Aug. 12, 1989 / assignee: Firma Carl Freudenberg. Inventors: Gunter Graf ; Heinz Gross ; Stefan Sponagel
Y1  - 1989
N1  - Barcode: US004861536A ; Volltext über Datenbank: http://www.google.com/patents
PB  - [United States Patent and Trademark Office]
CY  - [Alexandria, VA]
ER  - 
TY  - PAT
A1  - Sponagel, Stefan
A1  - Graf, Günter
A1  - Groß, Heinz
T1  - Method for the manufacture of a sealing ring with a sealing lip having hydrodynamically acting return elements : United States Patent 4,850,097 ; date of patent: Jul. 25, 1989 / assignee: Firma Carl Freudenberg. Inventors: Gunter Graf ; Heinz Gross ; Stefan Sponagel
Y1  - 1989
N1  - Barcode: US004850097A ; Volltext über Datenbank: http://www.google.com/patents
PB  - [United States Patent and Trademark Office]
CY  - [Alexandria, VA]
ER  - 
TY  - JOUR
A1  - Sponagel, Stefan
A1  - Baroud, G.
A1  - Steffen, T.
A1  - Wu, J.
T1  - Parameter identification for cement infiltration of osteoporotic bone
JF  - Poromechanics II : Proceedings of the Second Biot Conference on Poromechanics Grenoble, France 26 - 28 August 2002 / ed. by J.-L. Auriault ...
Y1  - 2002
SN  - 90-5809-394-8
SP  - 55
EP  - 58
PB  - Balkema
CY  - Lisse [u.a.]
ER  - 
TY  - JOUR
A1  - Sponagel, Stefan
A1  - Baroud, G.
A1  - Falk, R.
A1  - Crookshank, M.
T1  - Experimental and theoretical investigation of directional permeability of human vertebral cancellous bone for cement infiltration. G. Baroud, R. Falk, M. Crookshank, S. Sponagel, T. Steffen
JF  - Journal of Biomechanics. 37 (2004), H. 2
Y1  - 2004
SN  - 0021-9290
SP  - 189
EP  - 196
ER  - 
TY  - JOUR
A1  - Sponagel, Stefan
A1  - Baroud, G.
A1  - Falk, R.
A1  - Crookshank, M.
T1  - Corrigendum to “Experimental and theoretical investigation of directional permeability of human vertebral cancellous bone for cement infiltration”. Baroud, G.; Falk, R.; Crookshank, M.; Sponagel, S.; Steffen, T.
JF  - Journal of Biomechanics. 37 (2004), H. 2
Y1  - 2004
SN  - 0021-9290
SP  - 1802
ER  - 
TY  - JOUR
A1  - Sponagel, Stefan
A1  - Akbay, U.
A1  - Becker, E.
A1  - Krozer, S.
T1  - Instability of slow viscometric flow
JF  - Mechanics Research Communications. 7 (1980), H. 4
Y1  - 1980
SN  - 0093-6413
SP  - 199
EP  - 204
ER  - 
TY  - JOUR
A1  - Sponagel, Stefan
A1  - Akbay, U.
A1  - Becker, E.
T1  - Instability of plane Couette flow of viscoelastic liquids
JF  - Journal of non-Newtonian fluid mechanics. 18 (1985), H. 2
Y1  - 1985
SN  - 0377-0257
SP  - 123
EP  - 141
ER  - 
TY  - JOUR
A1  - Sponagel, Stefan
A1  - Adbay, U.
A1  - Becker, E.
A1  - Krozer, S.
T1  - A possible cause of viscoelastic turbulence
JF  - Rheology : proceedings of the 8th International Congress of Rheology, held in Naples, Italy, September 1 - 5, 1980 / Hrsg. von Giovanni Astarita, Vol. 2
Y1  - 1980
SN  - 0-306-40465-6
SP  - 79
EP  - 84
PB  - Plenum Pr.
CY  - New York
ER  - 
TY  - JOUR
A1  - Spelthahn, Heiko
A1  - Schubert, Jürgen
A1  - Schöning, Michael Josef
T1  - Dünnschichtsensoren für die Schwermetallanalytik
JF  - GIT : Labor-Fachzeitschrift
N2  - Die Detektion von Schadstoffen repräsentiert in der Umweltanalytik eine wichtige Aufgabenstellung. Gerade die Abwasser- bzw. Brauchwasseranalytik sowie die Prozesskontrolle haben einen hohen Stellenwert. Siliziumbasierte Dünnschichtsensoren bieten eine kostengünstige Möglichkeit, „online“-Messungen bzw. Vor-Ort-Messungen zeitnah durchzuführen. In dieser Arbeit wird ein potentiometrisches Sensorarray auf der Basis von Chalkogenidgläsern zur Detektion von Schwermetallen in wässrigen Medien vorgestellt.
Y1  - 2012
SN  - 0016-3538
VL  - 56
IS  - 4
SP  - 285
EP  - 287
PB  - Wiley-VCH
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Spelthahn, Heiko
A1  - Schaffrath, Sophie
A1  - Coppe, Thomas
A1  - Rufi, Frederic
A1  - Schöning, Michael Josef
T1  - Development of an electrolyte-insulator-semiconductor (EIS) based capacitive heavy metal sensor for the detection of Pb2+ und Cd2+ ions
JF  - Physica status solidi (a) : applications and material science. 207 (2010), H. 4
Y1  - 2010
SN  - 1862-6300
N1  - Special Issue: Engineering of Functional Interfaces EnFI 2009
SP  - 930
EP  - 934
ER  - 
TY  - JOUR
A1  - Spelthahn, Heiko
A1  - Poghossian, Arshak
A1  - Schöning, Michael Josef
T1  - Self-aligned nanogaps and nanochannels via conventional photolithography and pattern-size reduction technique
JF  - Electrochimica Acta. 54 (2009), H. 25 Sp. Iss. SI
Y1  - 2009
SN  - 0013-4686
SP  - 6010
EP  - 6014
ER  - 
TY  - JOUR
A1  - Spelthahn, Heiko
A1  - Kirsanov, Dmitry
A1  - Legin, Andrey
A1  - Osterrath, Thomas
A1  - Schubert, Jürgen
A1  - Zander, Willi
A1  - Schöning, Michael Josef
T1  - Development of a thin-film sensor array for analytical monitoring of heavy metals in aqueous solutions
JF  - Physica Status Solidi (a)
N2  - In industrial processes there is a variety of heavy metals (e.g., copper, zinc, cadmium, and lead) in use for wires, coatings, paints, alloys, batteries, etc. Since the application of these transition metals for industry is inevitable, it is a vital task to develop proper analytical techniques for their monitoring at low activity levels, especially because most of these elements are acutely toxic for biological organisms. The determination of ions in solution by means of a simple and inexpensive sensor array is, therefore, a promising task. In this work, a sensor array with heavy metal-sensitive chalcogenide glass membranes for the simultaneous detection of the four ions Ag⁺, Cu2⁺, Cd2⁺, and Pb2⁺ in solution is realized. The results of the physical characterization by means of microscopy, profilometry, Rutherford backscattering spectroscopy (RBS), and scanning electron microscopy (SEM) as well as the electrochemical characterization by means of potentiometric measurements are presented. Additionally, the possibility to expand the sensor array by polymeric sensor membranes is discussed.
Y1  - 2012
SN  - 1862-6319
U6  - http://dx.doi.org/10.1002/pssa.201100733
VL  - 209
IS  - 5
SP  - 885
EP  - 891
PB  - Wiley-VCH
CY  - Weinheim
ER  - 
TY  - CHAP
A1  - Spannhake, Jan
A1  - Schulz, Olaf
A1  - Helwig, Andreas
A1  - Krenkow, Angelika
A1  - Müller, Gerhard
A1  - Doll, Theodor
T1  - High-temperature MEMS heater platforms: long-term performance of metal and semiconductor heater materials
N2  - Micromachined thermal heater platforms offer low electrical power consumption and high modulation speed, i.e. properties which are advantageous for realizing nondispersive infrared (NDIR) gas- and liquid monitoring systems. In this paper, we report on investigations on silicon-on-insulator (SOI) based infrared (IR) emitter devices heated by employing different kinds of metallic and semiconductor heater materials. Our results clearly reveal the superior high-temperature performance of semiconductor over metallic heater materials. Long-term stable emitter operation in the vicinity of 1300 K could be attained using heavily antimony-doped tin dioxide (SnO2:Sb) heater elements.
KW  - Biosensor
KW  - Hotplate
KW  - heater metallisation
KW  - high-temperature stability
KW  - electro-migration
KW  - doped silicon
KW  - doped metal oxide
KW  - antimony doped tin oxide
Y1  - 2006
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:a96-opus-1513
ER  - 
TY  - JOUR
A1  - Sousa, Marcos A. M.
A1  - Siqueira, Jose R. Jr.
A1  - Vercik, Andres
A1  - Schöning, Michael Josef
A1  - Oliveira, Osvaldo N. Jr.
T1  - Determining the optimized layer-by-layer film architecture with dendrimer/carbon nanotubes for field-effect sensors
JF  - IEEE Sensors Journal
N2  - The capacitive electrolyte–insulator–semiconductor (EIS) structure is a typical device based on a field-effect sensor platform. With a simple silicon-based structure, EIS have been useful for several sensing applications, especially with incorporation of nanostructured films to modulate the ionic transport and the flat-band potential. In this paper, we report on ion transport and changes in flat-band potential in EIS sensors made with layer-by-layer films containing poly(amidoamine) (PAMAM) dendrimer and single-walled carbon nanotubes (SWNTs) adsorbed on p-Si/SiO 2 /Ta 2 O 5 chips with an Al ohmic contact. The impedance spectra were fitted using an equivalent circuit model, from which we could determine parameters such as the double-layer capacitance. This capacitance decreased with the number of bilayers owing to space charge accumulated at the electrolyte–insulator interface, up to three PAMAM/SWNTs bilayers, after which it stabilized. The charge-transfer resistance was also minimum for three bilayers, thus indicating that this is the ideal architecture for an optimized EIS performance. The understanding of the influence of nanostructures and the fine control of operation parameters pave the way for optimizing the design and performance of new EIS sensors.
Y1  - 2017
U6  - http://dx.doi.org/10.1109/JSEN.2017.2653238
SN  - 1558-1748
VL  - 17
IS  - 6
SP  - 1735
EP  - 1740
PB  - IEEE
CY  - New York
ER  - 
TY  - JOUR
A1  - Slabu, Ioana
A1  - Roeth, Anjali A.
A1  - Engelmann, Ulrich M.
A1  - Wiekhorst, Frank
A1  - Buhl, Eva M.
A1  - Neumann, Ulf P.
A1  - Schmitz-Rode, Thomas
T1  - Modeling of magnetoliposome uptake in human pancreatic tumor cells in vitro
JF  - Nanotechnology
Y1  - 2019
U6  - http://dx.doi.org/10.1088/1361-6528/ab033e
SN  - 1361-6528
VL  - 30
IS  - 18
SP  - 184004
ER  - 
TY  - JOUR
A1  - Siqueira, José R. Jr.
A1  - Bäcker, Matthias
A1  - Poghossian, Arshak
A1  - Zucolotto, Valtencir
A1  - Oliveira, Osvaldo N. Jr.
A1  - Schöning, Michael Josef
T1  - Associating biosensing properties with the morphological structure of multilayers containing carbon nanotubes on field-effect devices
JF  - Physica status solidi (a). 207 (2010), H. 4
Y1  - 2010
SN  - 1862-6300
N1  - Special Issue: Engineering of Functional Interfaces EnFI 2009
SP  - 781
EP  - 786
ER  - 
TY  - JOUR
A1  - Siqueira, José R. Jr.
A1  - Abouzar, Maryam H.
A1  - Poghossian, Arshak
A1  - Zucolotto, Valtencir
A1  - Oliveira, Osvaldo N. Jr.
A1  - Schöning, Michael Josef
T1  - Penicillin biosensor based on a capacitive field-effect structure functionalized with a dendrimer/carbon nanotube multilayer
JF  - Biosensors and Bioelectronics. 25 (2009), H. 2
Y1  - 2009
SN  - 0956-5663
SP  - 497
EP  - 501
ER  - 
TY  - JOUR
A1  - Siqueira, José R. Jr.
A1  - Abouzar, Maryam H.
A1  - Bäcker, Matthias
A1  - Zucolotto, Valtencir
A1  - Poghossian, Arshak
A1  - Oliveira, Osvaldo N. Jr.
A1  - Schöning, Michael Josef
T1  - Carbon nanotubes in nanostructured films: Potential application as amperometric and potentiometric field-effect (bio-)chemical sensors
JF  - physica status solidi (a) . 206 (2009), H. 3
Y1  - 2009
SN  - 1862-6319
N1  - Special Issue: Engineering of Functional Interfaces (EnFI 08)
SP  - 462
EP  - 467
PB  - Wiley
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Siqueira, Jose R.
A1  - Werner, Frederik
A1  - Bäcker, Matthias
A1  - Poghossian, Arshak
A1  - Zucolotto, Valtencir
A1  - Oliveira, Osvaldo N. Jr.
A1  - Schöning, Michael Josef
T1  - Layer-by-Layer Assembly of Carbon Nanotubes Incorporated in Light-Addressable Potentiometric Sensors
JF  - Journal of Physical Chemistry C. 113 (2009), H. 33
Y1  - 2009
SN  - 1932-7455
SP  - 14765
EP  - 14770
PB  - American Chemical Society
CY  - Washington, DC
ER  - 
TY  - JOUR
A1  - Siqueira, Jose R.
A1  - Molinnus, Denise
A1  - Beging, Stefan
A1  - Schöning, Michael Josef
T1  - Incorporating a hybrid urease-carbon nanotubes sensitive nanofilm on capacitive field-effect sensors for urea detection
JF  - Analytical chemistry
N2  - The ideal combination among biomolecules and nanomaterials is the key for reaching biosensing units with high sensitivity. The challenge, however, is to find out a stable and sensitive film architecture that can be incorporated on the sensor’s surface. In this paper, we report on the benefits of incorporating a layer-by-layer (LbL) nanofilm of polyamidoamine (PAMAM) dendrimer and carbon nanotubes (CNTs) on capacitive electrolyte-insulator-semiconductor (EIS) field-effect sensors for detecting urea. Three sensor arrangements were studied in order to investigate the adequate film architecture, involving the LbL film with the enzyme urease: (i) urease immobilized directly onto a bare EIS [EIS-urease] sensor; (ii) urease atop the LbL film over the EIS [EIS-(PAMAM/CNT)-urease] sensor; and (iii) urease sandwiched between the LbL film and another CNT layer [EIS-(PAMAM/CNT)-urease-CNT]. The surface morphology of all three urea-based EIS biosensors was investigated by atomic force microscopy (AFM), while the biosensing abilities were studied by means of capacitance–voltage (C/V) and dynamic constant-capacitance (ConCap) measureaments at urea concentrations ranging from 0.1 mM to 100 mM. The EIS-urease and EIS-(PAMAM/CNT)-urease sensors showed similar sensitivity (∼18 mV/decade) and a nonregular signal behavior as the urea concentration increased. On the other hand, the EIS-(PAMAM/CNT)-urease-CNT sensor exhibited a superior output signal performance and higher sensitivity of about 33 mV/decade. The presence of the additional CNT layer was decisive to achieve a urea based EIS sensor with enhanced properties. Such sensitive architecture demonstrates that the incorporation of an adequate hybrid enzyme-nanofilm as sensing unit opens new prospects for biosensing applications using the field-effect sensor platform.
Y1  - 2014
U6  - http://dx.doi.org/10.1021/ac500458s
SN  - 1520-6882 (E-Journal); 0003-2700 (Print); 0096-4484 (Print)
VL  - 86
IS  - 11
SP  - 5370
EP  - 5375
PB  - ACS Publications
CY  - Columbus
ER  - 
TY  - JOUR
A1  - Siqueira, Jose R.
A1  - Maki, Rafael M.
A1  - Paulovich, Fernando V.
A1  - Werner, Frederik
A1  - Poghossian, Arshak
A1  - Oliveira, Maria C. F. de
A1  - Zucolotto, Valtencir
A1  - Oliveira, Osvaldo N. Jr.
A1  - Schöning, Michael Josef
T1  - Use of Information Visualization Methods Eliminating Cross Talk in Multiple Sensing Units Investigated for a Light-Addressable Potentiometric Sensor
JF  - Analytical Chemistry  (2010)
Y1  - 2010
SN  - 0003-2700
SP  - 61
EP  - 65
ER  - 
TY  - CHAP
A1  - Simsek, Beril
A1  - Krause, Hans-Joachim
A1  - Engelmann, Ulrich M.
ED  - Digel, Ilya
ED  - Staat, Manfred
ED  - Trzewik, Jürgen
ED  - Sielemann, Stefanie
ED  - Erni, Daniel
ED  - Zylka, Waldemar
T1  - Magnetic biosensing with magnetic nanoparticles: Simulative approach to predict signal intensity in frequency mixing magnetic detection
T2  - 4th YRA MedTech Symposium 2024 : February 1 / 2024 / FH Aachen
N2  - Magnetic nanoparticles (MNP) are investigated with great interest for biomedical applications in diagnostics (e.g. imaging: magnetic particle imaging (MPI)), therapeutics (e.g. hyperthermia: magnetic fluid hyperthermia (MFH)) and multi-purpose biosensing (e.g. magnetic immunoassays (MIA)). What all of these applications have in common is that they are based on the unique magnetic relaxation mechanisms of MNP in an alternating magnetic field (AMF). While MFH and MPI are currently the most prominent examples of biomedical applications, here we present results on the relatively new biosensing application of frequency mixing magnetic detection (FMMD) from a simulation perspective. In general, we ask how the key parameters of MNP (core size and magnetic anisotropy) affect the FMMD signal: by varying the core size, we investigate the effect of the magnetic volume per MNP; and by changing the effective magnetic anisotropy, we study the MNPs’ flexibility to leave its preferred magnetization direction. From this, we predict the most effective combination of MNP core size and magnetic anisotropy for maximum signal generation.
Y1  - 2024
SN  - 978-3-940402-65-3
U6  - http://dx.doi.org/10.17185/duepublico/81475
SP  - 27
EP  - 28
PB  - Universität Duisburg-Essen
CY  - Duisburg
ER  - 
TY  - JOUR
A1  - Simonis, A.
A1  - Ruge, C.
A1  - Müller-Veggian, Mattea
A1  - Lüth, H.
A1  - Schöning, Michael Josef
T1  - A long-term stable macroporoustype EIS structure for electrochemical sensor applications
JF  - Sensors and Actuators B. 91 (2003), H. 1-3
Y1  - 2003
SN  - 0925-4005
SP  - 21
EP  - 25
ER  - 
TY  - JOUR
A1  - Simonis, A.
A1  - Lüth, H.
A1  - Wang, J.
A1  - Schöning, Michael Josef
T1  - New concepts of miniaturised reference electrodes in silicon technology for potentiometric sensor systems
JF  - Sensors and Actuators B. 103 (2004), H. 1-2
Y1  - 2004
SN  - 0925-4005
SP  - 429
EP  - 435
ER  - 
TY  - JOUR
A1  - Simonis, A.
A1  - Lüth, H.
A1  - Wang, J.
A1  - Schöning, Michael Josef
T1  - Strategies of miniaturised reference electrodes integrated in a silicon-based „one chip“ pH sensor
JF  - Sensors. 3 (2003), H. 9
Y1  - 2003
SN  - 1424-8220
SP  - 330
EP  - 339
ER  - 
TY  - JOUR
A1  - Simonis, A.
A1  - Krings, T.
A1  - Lüth, H.
A1  - Wang, J.
A1  - Schöning, Michael Josef
T1  - A „hybrid“ thin-film pH sensor with integrated thick-film reference
JF  - Sensors. 1 (2001), H. 6
Y1  - 2001
SN  - 1424-8220
SP  - 183
EP  - 192
ER  - 
TY  - JOUR
A1  - Simonis, A.
A1  - Dawgul, M.
A1  - Lüth, H.
A1  - Schöning, Michael Josef
T1  - Miniaturised reference electrodes for field-effect sensors compatible to silicon chip technology
JF  - Electrochimica Acta. 51 (2005), H. 5
Y1  - 2005
SN  - 0013-4686
U6  - http://dx.doi.org/10.1016/j.electacta.2005.04.063
SP  - 930
EP  - 937
ER  - 
TY  - JOUR
A1  - Sildatke, Michael
A1  - Karwanni, Hendrik
A1  - Kraft, Bodo
A1  - Zündorf, Albert
T1  - A distributed microservice architecture pattern for the automated generation of information extraction pipelines
JF  - SN Computer Science
N2  - Companies often build their businesses based on product information and therefore try to automate the process of information extraction (IE). Since the information source is usually heterogeneous and non-standardized, classic extract, transform, load techniques reach their limits. Hence, companies must implement the newest findings from research to tackle the challenges of process automation. They require a flexible and robust system that is extendable and ensures the optimal processing of the different document types. This paper provides a distributed microservice architecture pattern that enables the automated generation of IE pipelines. Since their optimal design is individual for each input document, the system ensures the ad-hoc generation of pipelines depending on specific document characteristics at runtime. Furthermore, it introduces the automated quality determination of each available pipeline and controls the integration of new microservices based on their impact on the business value. The introduced system enables fast prototyping of the newest approaches from research and supports companies in automating their IE processes. Based on the automated quality determination, it ensures that the generated pipelines always meet defined business requirements when they come into productive use.
KW  - Architectural design
KW  - Model-driven software engineering
KW  - Software and systems modeling
KW  - Enterprise information systems
KW  - Information extraction
Y1  - 2023
U6  - http://dx.doi.org/10.1007/s42979-023-02256-4
SN  - 2661-8907
N1  - Corresponding authors: Michael Sildatke, Hendrik Karwanni
IS  - 4, Article number: 833
PB  - Springer Singapore
CY  - Singapore
ER  - 
TY  - CHAP
A1  - Sildatke, Michael
A1  - Karwanni, Hendrik
A1  - Kraft, Bodo
A1  - Schmidts, Oliver
A1  - Zündorf, Albert
T1  - Automated Software Quality Monitoring in Research Collaboration Projects
T2  - ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops
Y1  - 2020
U6  - http://dx.doi.org/10.1145/3387940.3391478
SP  - 603
EP  - 610
ER  - 
TY  - CHAP
A1  - Siebigteroth, Ines
A1  - Kraft, Bodo
A1  - Schmidts, Oliver
A1  - Zündorf, Albert
T1  - A Study on Improving Corpus Creation by Pair Annotation
T2  - Proceedings of the Poster Session of the 2nd Conference on Language, Data and Knowledge (LDK-PS 2019)
Y1  - 2019
SN  - 1613-0073
SP  - 40
EP  - 44
ER  - 
TY  - JOUR
A1  - Seynnes, O. R.
A1  - Bojsen-Moller, J.
A1  - Albracht, Kirsten
A1  - Arndt, A.
A1  - Cronin, N. J.
A1  - Finni, T.
A1  - Magnusson, S. P.
T1  - Ultrasound-based testing of tendon mechanical properties: a critical evaluation
JF  - Journal of Applied Physiology
Y1  - 2015
U6  - http://dx.doi.org/10.1152/japplphysiol.00849.2014
SN  - 8750-7587
VL  - 118
IS  - 2
SP  - 133
EP  - 141
ER  - 
TY  - JOUR
A1  - Seifarth, Volker
A1  - Schehl, D.
A1  - Linder, Peter
A1  - Gossmann, Matthias
A1  - Digel, Ilya
A1  - Artmann, Gerhard
A1  - Porst, Dariusz
A1  - Preiß, C.
A1  - Kayser, Peter
A1  - Pack, O.
A1  - Temiz Artmann, Aysegül
T1  - Ureplace: development of a bioreactor for in vitro culturing of cell seeded tubular vessels on collagen scaffolds
N2  - The demand of replacements for inoperable organs exceeds the amount of available organ transplants. Therefore, tissue engineering developed as a multidisciplinary field of research for autologous in-vitro organs. Such three dimensional tissue constructs request the application of a bioreactor. The UREPLACE bioreactor is used to grow cells on tubular collagen scaffolds OPTIMAIX Sponge 1 with a maximal length of 7 cm, in order to culture in vitro an adequate ureter replacement. With a rotating unit, (urothelial) cells can be placed homogeneously on the inner scaffold surface. Furthermore, a stimulation is combined with this bioreactor resulting in an orientation of muscle cells. These culturing methods request a precise control of several parameters and actuators. A combination of a LabBox and the suitable software LabVision is used to set and conduct parameters like rotation angles, velocities, pressures and other important cell culture values. The bioreactor was tested waterproof successfully. Furthermore, the temperature controlling was adjusted to 37 °C and the CO2 - concentration regulated to 5 %. Additionally, the pH step responses of several substances showed a perfect functioning of the designed flow chamber. All used software was tested and remained stable for several days.
KW  - Tissue Engineering
KW  - Bioreaktor
KW  - Organkultur
KW  - Harnleiter
Y1  - 2011
ER  - 
TY  - THES
A1  - Seifarth, Volker
T1  - Ureteral tissue engineering : development of a bioreactor system and subsequent characterization of the generated biohybrids
Y1  - 2015
N1  - Duisburg, Essen, Universität Duisburg-Essen, Diss., 2015
PB  - Universitätsbibliothek Duisburg-Essen
CY  - Duisburg ; Essen
ER  - 
TY  - JOUR
A1  - Seidova, Seid-Fatima
A1  - Kotliar, Konstantin
A1  - Foerger, Frauke
A1  - Klopfer, Matthias
A1  - Lanzl, Ines
T1  - Functional retinal changes in Gaucher disease
JF  - Documenta Ophthalmologica
Y1  - 2009
SN  - 1573-2622
VL  - 118
IS  - 2
SP  - 151
EP  - 154
PB  - Springer
CY  - Berlin
ER  - 
TY  - JOUR
A1  - Schütz, S.
A1  - Weißbecker, G.
A1  - Schroth, P.
A1  - Schöning, Michael Josef
T1  - Linkage of inanimate structures to biological systems – smart materials in biological micro- nanosystems
JF  - Smart materials : proceedings of the 1st Caesarium, Bonn, November 17 - 19, 1999 / Karl-Heinz Hoffmann ed.
Y1  - 2001
SN  - 3-540-67957-X
SP  - 149
EP  - 157
PB  - Springer
CY  - Berlin [u.a.]
ER  - 
TY  - JOUR
A1  - Schütz, S.
A1  - Weißbecker, B.
A1  - Hummel, Hans E.
A1  - Schöning, Michael Josef
A1  - Riemer, A.
A1  - Kordos, P.
A1  - Lüth, H.
T1  - Field effect transistor-insect antenna junction
JF  - Naturwissenschaften
Y1  - 1997
SN  - 1432-1904
VL  - 84
SP  - 86
EP  - 88
ER  -