TY  - JOUR
A1  - Neu, Eugen
A1  - Janser, Frank
A1  - Khatibi, Akbar A.
A1  - Orifici, Adrian C.
T1  - Automated modal parameter-based anomaly detection under varying wind excitation
JF  - Structural Health Monitoring
N2  - Wind-induced operational variability is one of the major challenges for structural health monitoring of slender engineering structures like aircraft wings or wind turbine blades. Damage sensitive features often show an even bigger sensitivity to operational variability. In this study a composite cantilever was subjected to multiple mass configurations, velocities and angles of attack in a controlled wind tunnel environment. A small-scale impact damage was introduced to the specimen and the structural response measurements were repeated. The proposed damage detection methodology is based on automated operational modal analysis. A novel baseline preparation procedure is described that reduces the amount of user interaction to the provision of a single consistency threshold. The procedure starts with an indeterminate number of operational modal analysis identifications from a large number of datasets and returns a complete baseline matrix of natural frequencies and damping ratios that is suitable for subsequent anomaly detection. Mahalanobis distance-based anomaly detection is then applied to successfully detect the damage under varying severities of operational variability and with various degrees of knowledge about the present operational conditions. The damage detection capabilities of the proposed methodology were found to be excellent under varying velocities and angles of attack. Damage detection was less successful under joint mass and wind variability but could be significantly improved through the provision of the currently encountered operational conditions.
Y1  - 2016
U6  - https://doi.org/10.1177/1475921716665803
SN  - 1475-9217
VL  - 15
IS  - 6
SP  - 1
EP  - 20
PB  - Sage
CY  - London
ER  - 
TY  - THES
A1  - Pfaff, Raphael
T1  - Automated processing of the ISL Doppler images
Y1  - 2007
N1  - Hagen, Fernuniv., Bachelorarbeit, 2007
ER  - 
TY  - JOUR
A1  - Grieger, Niklas
A1  - Schwabedal, Justus T. C.
A1  - Wendel, Stefanie
A1  - Ritze, Yvonne
A1  - Bialonski, Stephan
T1  - Automated scoring of pre-REM sleep in mice with deep learning
JF  - Scientific Reports
N2  - Reliable automation of the labor-intensive manual task of scoring animal sleep can facilitate the analysis of long-term sleep studies. In recent years, deep-learning-based systems, which learn optimal features from the data, increased scoring accuracies for the classical sleep stages of Wake, REM, and Non-REM. Meanwhile, it has been recognized that the statistics of transitional stages such as pre-REM, found between Non-REM and REM, may hold additional insight into the physiology of sleep and are now under vivid investigation. We propose a classification system based on a simple neural network architecture that scores the classical stages as well as pre-REM sleep in mice. When restricted to the classical stages, the optimized network showed state-of-the-art classification performance with an out-of-sample F1 score of 0.95 in male C57BL/6J mice. When unrestricted, the network showed lower F1 scores on pre-REM (0.5) compared to the classical stages. The result is comparable to previous attempts to score transitional stages in other species such as transition sleep in rats or N1 sleep in humans. Nevertheless, we observed that the sequence of predictions including pre-REM typically transitioned from Non-REM to REM reflecting sleep dynamics observed by human scorers. Our findings provide further evidence for the difficulty of scoring transitional sleep stages, likely because such stages of sleep are under-represented in typical data sets or show large inter-scorer variability. We further provide our source code and an online platform to run predictions with our trained network.
Y1  - 2021
U6  - https://doi.org/10.1038/s41598-021-91286-0
SN  - 2045-2322
N1  - Corresponding author: Stephan Bialonski
VL  - 11
IS  - Art. 12245
PB  - Springer Nature
CY  - London
ER  - 
TY  - CHAP
A1  - Sildatke, Michael
A1  - Karwanni, Hendrik
A1  - Kraft, Bodo
A1  - Schmidts, Oliver
A1  - Zündorf, Albert
T1  - Automated Software Quality Monitoring in Research Collaboration Projects
T2  - ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops
N2  - In collaborative research projects, both researchers and practitioners work together solving business-critical challenges. These projects often deal with ETL processes, in which humans extract information from non-machine-readable documents by hand. AI-based machine learning models can help to solve this problem.

Since machine learning approaches are not deterministic, their quality of output may decrease over time. This fact leads to an overall quality loss of the application which embeds machine learning models. Hence, the software qualities in development and production may differ.

Machine learning models are black boxes. That makes practitioners skeptical and increases the inhibition threshold for early productive use of research prototypes. Continuous monitoring of software quality in production offers an early response capability on quality loss and encourages the use of machine learning approaches. Furthermore, experts have to ensure that they integrate possible new inputs into the model training as quickly as possible.

In this paper, we introduce an architecture pattern with a reference implementation that extends the concept of Metrics Driven Research Collaboration with an automated software quality monitoring in productive use and a possibility to auto-generate new test data coming from processed documents in production.

Through automated monitoring of the software quality and auto-generated test data, this approach ensures that the software quality meets and keeps requested thresholds in productive use, even during further continuous deployment and changing input data.
Y1  - 2020
U6  - https://doi.org/10.1145/3387940.3391478
N1  - ICSE '20: 42nd International Conference on Software Engineering, Seoul, Republic of Korea, 27 June 2020 - 19 July 2020
SP  - 603
EP  - 610
PB  - IEEE
CY  - New York, NY
ER  - 
TY  - JOUR
A1  - Schmitz, Günter
A1  - Oligschläger, U.
A1  - Eifler, G.
A1  - Lechner, H.
T1  - Automated System for Optimized Calibration of Engine Management Systems
Y1  - 1994
N1  - SAE International Congress and Exposition, Detroit, Feb. 28 - March 3 ; SAE- Paper-No.: 940151 ; <a href=
ER  - 
TY  - CHAP
A1  - Butenweg, Christoph
A1  - Thierauf, G.
ED  - Papadrakakis, M.
ED  - Topping, B.H.V.
T1  - Automatic design of reinforced concrete structures with parallel computing
T2  - Innovative computational methods for structural mechanics
N2  - A concept for the analysis and optimal design of reinforced concrete structures is described. It is based on a nonlinear optimization algorithm and a finite element program for linear and nonlinear analysis of structures. With the aim of minimal cost design a two stage optimization using efficient gradient algorithm is developed. The optimization problems on global (structural) and local (crosssectional) level are formulated. A parallelization concept for solving the two stage optimization problem in minimal time is presented. Examples are included to illustrate the practical use and the effectively of the parallelization in the area of engineering design.
Y1  - 1999
SN  - 1-874672-05-9
U6  - https://doi.org/10.4203/csets.1.14
SP  - 305
EP  - 318
PB  - Saxe-Coburg Publication
CY  - Edinburgh
ER  - 
TY  - JOUR
A1  - Marx, Ulrich
A1  - Schenk, Friedrich
A1  - Behrens, Jan
A1  - Meyr, Ulrike
A1  - Wanek, Paul
A1  - Zang, Werner
A1  - Schmitt, Robert
A1  - Brüstle, Oliver
A1  - Zenke, Martin
A1  - Klocke, Fritz
T1  - Automatic production of induced pluripotent stem cells
JF  - Procedia CIRP : First CIRP Conference on BioManufacturing
Y1  - 2013
SN  - 2212-8271
VL  - Vol. 5
SP  - 2
EP  - 6
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Blaneck, Patrick Gustav
A1  - Bornheim, Tobias
A1  - Grieger, Niklas
A1  - Bialonski, Stephan
T1  - Automatic readability assessment of german sentences with transformer ensembles
T2  - Proceedings of the GermEval 2022 Workshop on Text Complexity Assessment of German Text
N2  - Reliable methods for automatic readability assessment have the potential to impact a variety of fields, ranging from machine translation to self-informed learning. Recently, large language models for the German language (such as GBERT and GPT-2-Wechsel) have become available, allowing to develop Deep Learning based approaches that promise to further improve automatic readability assessment. In this contribution, we studied the ability of ensembles of fine-tuned GBERT and GPT-2-Wechsel models to reliably predict the readability of German sentences. We combined these models with linguistic features and investigated the dependence of prediction performance on ensemble size and composition. Mixed ensembles of GBERT and GPT-2-Wechsel performed better than ensembles of the same size consisting of only GBERT or GPT-2-Wechsel models. Our models were evaluated in the GermEval 2022 Shared Task on Text Complexity Assessment on data of German sentences. On out-of-sample data, our best ensemble achieved a root mean squared error of 0:435.
Y1  - 2022
U6  - https://doi.org/10.48550/arXiv.2209.04299
N1  - Proceedings of the 18th Conference on Natural Language Processing / Konferenz zur Verarbeitung natürlicher Sprache (KONVENS 2022), 12-15 September, 2022, University of Potsdam, Potsdam, Germany
SP  - 57
EP  - 62
PB  - Association for Computational Linguistics
CY  - Potsdam
ER  - 
TY  - JOUR
A1  - Rake, Heinrich
A1  - Enning, Manfred
A1  - Kurth, Johannes
A1  - Schröder, Walter
T1  - Automatic uncoupler completes automation at the hump
JF  - RGI - Railway Gazette International
Y1  - 1994
SN  - 0373-5346
VL  - 150
IS  - 6
SP  - 371
EP  - 374
PB  - Reed Business
CY  - Sutton
ER  - 
TY  - JOUR
A1  - Enning, Manfred
A1  - Bernhard, S.
A1  - Rake, H.
T1  - Automation of a laboratory plant for direct casting of thin steel strips / Bernhard, S. ; Enning, M. ; Rake, H.
JF  - Control Engineering Practice. 2 (1994), H. 6
Y1  - 1994
SN  - 0967-0661
SP  - 961
EP  - 967
ER  - 
TY  - JOUR
A1  - Biselli, Manfred
A1  - Van der Pol, Jens J.
A1  - De Gooijer, Cornelis D.
A1  - Wandrey, Christian
T1  - Automation of selective assays for on-line bioprocess monitoring by  flow-injection analysis / van der Pol, Jens J. ; de Gooijer, Cornelis D. ; Biselli, Manfred ; Wandrey, Christian ; Tramper, Johannes
JF  - Trends in Biotechnology. 14 (1996), H. 12
Y1  - 1996
SN  - 0167-7799
SP  - 471
EP  - 477
ER  - 
TY  - JOUR
A1  - Laarmann, Lukas
A1  - Thoma, Andreas
A1  - Misch, Philipp
A1  - Röth, Thilo
A1  - Braun, Carsten
A1  - Watkins, Simon
A1  - Fard, Mohammad
T1  - Automotive safety approach for future eVTOL vehicles
JF  - CEAS Aeronautical Journal
N2  - The eVTOL industry is a rapidly growing mass market expected to start in 2024. eVTOL compete, caused by their predicted missions, with ground-based transportation modes, including  mainly passenger cars. Therefore, the automotive and classical aircraft design process is reviewed and compared to highlight advantages for eVTOL development. A special focus is on ergonomic comfort and safety. The need for further investigation of eVTOL’s crashworthiness is outlined by, first, specifying the relevance of passive safety via accident statistics and customer perception analysis; second, comparing the current state of regulation and certification; and third, discussing the advantages of integral safety and applying the automotive safety approach for eVTOL development. Integral safety links active and passive safety, while the automotive safety approach means implementing standardized mandatory full-vehicle crash tests for future eVTOL. Subsequently, possible crash impact conditions are analyzed, and three full-vehicle crash load cases are presented.
KW  - eVTOL development
KW  - eVTOL safety
KW  - Crashworthiness
KW  - Automotive safety approach
KW  - Full-vehicle crash test
Y1  - 2023
U6  - https://doi.org/10.1007/s13272-023-00655-0
SN  - 1869-5590 (Online)
SN  - 1869-5582 (Print)
N1  - Corresponding author: Lukas Laarmann
PB  - Springer Nature
ER  - 
TY  - CHAP
A1  - Engemann, Heiko
A1  - Wiesen, Patrick
A1  - Kallweit, Stephan
A1  - Deshpande, Harshavardhan
A1  - Schleupen, Josef
T1  - Autonomous mobile manipulation using ROS
T2  - Advances in Service and Industrial Robotics
Y1  - 2018
SN  - 978-3-319-61276-8
U6  - https://doi.org/10.1007/978-3-319-61276-8_43
N1  - International Conference on Robotics in Alpe-Adria Danube Region RAAD 2017;
Mechanisms and Machince Science book series, Vol 49.
SP  - 389
EP  - 401
PB  - Springer
CY  - Cham
ER  - 
TY  - JOUR
A1  - Enning, Manfred
A1  - Mann, S.
A1  - Bollig, A.
A1  - Kaierle, S.
T1  - Autonomous Production Cell for Laser Beam Welding / Mann S. ; Bollig, A. ; Kaierle, S. ; Abel, D. ; Poprawe, R.
Y1  - 2003
SN  - 0912035757
N1  - ICALEO 2003, Florida  ; Laser Materials Processing Conference ; (2003, Jacksonville, Fla.) ; ICALEO ; (22, 2003, Jacksonville, Fla.)
PB  - LIA
CY  - Orlando, Fla
ER  - 
TY  - JOUR
A1  - Benkner, Thorsten
T1  - Autonomous Slot Assignment Schemes for PRMA++ Third Generation TDMA Systems
JF  - Proceedings / Organization: IEEE Vehicular Technology/Communications Society; Joint Chapter in the Benelux Section and Telecommunications Division, Eindhoven University of Technology, The Netherlands. Ed.: Peter Smulders
Y1  - 1995
SN  - 9061449928
N1  - Symposium on Communications and Vehicular Technology in the Benelux ; (3, 1995, Eindhoven) ; Vehicular Technology Society ; Communications Society ; Institute of Electrical and Electronics Engineers. ; Benelux ; Technische Universiteit. ; Telecommunicatio
PB  - Techn. Univ. Eindhoven, Telecommunications Div.
CY  - Eindhoven
ER  - 
TY  - CHAP
A1  - Engemann, Heiko
A1  - Du, Shengzhi
A1  - Kallweit, Stephan
A1  - Ning, Chuanfang
A1  - Anwar, Saqib
T1  - AutoSynPose: Automatic Generation of Synthetic Datasets for 6D Object Pose Estimation
T2  - Machine Learning and Artificial Intelligence. Proceedings of MLIS 2020
N2  - We present an automated pipeline for the generation of synthetic datasets for six-dimension (6D) object pose estimation. Therefore, a completely automated generation process based on predefined settings is developed, which enables the user to create large datasets with a minimum of interaction and which is feasible for applications with a high object variance. The pipeline is based on the Unreal 4 (UE4) game engine and provides a high variation for domain randomization, such as object appearance, ambient lighting, camera-object transformation and distractor density. In addition to the object pose and bounding box, the metadata includes all randomization parameters, which enables further studies on randomization parameter tuning. The developed workflow is adaptable to other 3D objects and UE4 environments. An exemplary dataset is provided including five objects of the Yale-CMU-Berkeley (YCB) object set. The datasets consist of 6 million subsegments using 97 rendering locations in 12 different UE4 environments. Each dataset subsegment includes one RGB image, one depth image and one class segmentation image at pixel-level.
Y1  - 2020
SN  - 978-1-64368-137-5
U6  - https://doi.org/10.3233/FAIA200770
N1  - Frontiers in Artificial Intelligence and Applications. Vol 332
SP  - 89
EP  - 97
PB  - IOS Press
CY  - Amsterdam
ER  - 
TY  - CHAP
A1  - Rokitansky, Carl-Herbert
A1  - Ehammer, Max
A1  - Gräupl, Thomas
A1  - Schnell, Michael
A1  - Brandes, Sinja
A1  - Gligorevic, Snjezana
A1  - Rihacek, Christoph
A1  - Sajatovic, Miodrag
T1  - B-AMC a system for future broadband aeronautical multi-carrier communications in the L-BAND
T2  - IEEE/AIAA 26th Digital Avionics Systems Conference ; DASC '07 ; 21 - 25 Oct. 2007, Dallas, Texas
Y1  - 2007
SN  - 978-1-4244-1108-5
SP  - 4D2-1
EP  - 4D2-13
ER  - 
TY  - CHAP
A1  - Rokitansky, Carl-Herbert
A1  - Ehammer, Max
A1  - Gräupl, Thomas
A1  - Schnell, Michael
A1  - Brandes, Sinja
A1  - Gligorevic, Snjezana
A1  - Rihacek, Christoph
A1  - Sajatovic, Miodrag
T1  - B-AMC – Aeronautical Broadband Communication in the L-Band
T2  - First CEAS European Air and Space Conference : Motto: century perspectives : Deutscher Luft-und Raumfahrtkongress 2007 : 10-13 September 2007 in Berlin, Germany. (Jahrbuch der Deutschen Gesellschaft für Luft- und Raumfahrt 2007 ; Bd. 1-5. - Enth.: Jahrbuch der Deutschen Gesellschaft für Luft- und Raumfahrt 2006 ; Bd. 3)
Y1  - 2007
SN  - 0070-4083
SP  - 487
EP  - 496
PB  - Deutschen Gesellschaft für Luft- und Raumfahrt
CY  - Bonn
ER  - 
TY  - CHAP
T1  - B-AMC — broadband aeronautical multi-carrier communications
T2  - Integrated Communications, Navigation and Surveillance Conference : [ICNS 2008] ; Bethesda, Md., 5 - 7 May 2008
Y1  - 2008
SN  - 978-1-4244-2303-3 ; 978-1-4244-2304-0
SP  - 1
EP  - 12
ER  - 
TY  - JOUR
A1  - Handtke, Stefan
A1  - Schroeter, Rebecca
A1  - Jürgen, Britta
A1  - Methling, Karen
A1  - Schlüter, Rabea
A1  - Albrecht, Dirk
A1  - Hijum, Sacha A. F. T. van
A1  - Bongaerts, Johannes
A1  - Maurer, Karl-Heinz
A1  - Lalk, Michael
A1  - Schweder, Thomas
A1  - Hecker, Michael
A1  - Voigt, Birgit
T1  - Bacillus pumilus reveals a remarkably high resistance to hydrogen peroxide provoked oxidative stress
JF  - PLOS one
N2  - Bacillus pumilus is characterized by a higher oxidative stress resistance than other comparable industrially relevant Bacilli such as B. subtilis or B. licheniformis. In this study the response of B. pumilus to oxidative stress was investigated during a treatment with high concentrations of hydrogen peroxide at the proteome, transcriptome and metabolome level. Genes/proteins belonging to regulons, which are known to have important functions in the oxidative stress response of other organisms, were found to be upregulated, such as the Fur, Spx, SOS or CtsR regulon. Strikingly, parts of the fundamental PerR regulon responding to peroxide stress in B. subtilis are not encoded in the B. pumilus genome. Thus, B. pumilus misses the catalase KatA, the DNA-protection protein MrgA or the alkyl hydroperoxide reductase AhpCF. Data of this study suggests that the catalase KatX2 takes over the function of the missing KatA in the oxidative stress response of B. pumilus. The genome-wide expression analysis revealed an induction of bacillithiol (Cys-GlcN-malate, BSH) relevant genes. An analysis of the intracellular metabolites detected high intracellular levels of this protective metabolite, which indicates the importance of bacillithiol in the peroxide stress resistance of B. pumilus.
Y1  - 2014
U6  - https://doi.org/10.1371/journal.pone.0085625
SN  - 1932-6203
VL  - 9
IS  - 1
PB  - PLOS
CY  - San Francisco
ER  - 
TY  - JOUR
A1  - Christen, Marc
A1  - Bartelt, Perry
A1  - Kowalski, Julia
T1  - Back calculation of the In den Arelen avalanche with RAMMS: Interpretation of model results
JF  - Annals of Glaciology
N2  - Two- and three-dimensional avalanche dynamics models are being increasingly used in hazard-mitigation studies. These models can provide improved and more accurate results for hazard mapping than the simple one-dimensional models presently used in practice. However, two- and three-dimensional models generate an extensive amount of output data, making the interpretation of simulation results more difficult. To perform a simulation in three-dimensional terrain, numerical models require a digital elevation model, specification of avalanche release areas (spatial extent and volume), selection of solution methods, finding an adequate calculation resolution and, finally, the choice of friction parameters. In this paper, the importance and difficulty of correctly setting up and analysing the results of a numerical avalanche dynamics simulation is discussed. We apply the two-dimensional simulation program RAMMS to the 1968 extreme avalanche event In den Arelen. We show the effect of model input variations on simulation results and the dangers and complexities in their interpretation.
KW  - avalanche
Y1  - 2010
SN  - 1727-5644
U6  - https://doi.org/10.3189/172756410791386553
VL  - 51
IS  - 54
SP  - 161
EP  - 168
PB  - Cambridge University Press
CY  - Cambridge
ER  - 
TY  - JOUR
A1  - Pogorelova, Natalia
A1  - Rogachev, Evgeniy
A1  - Digel, Ilya
A1  - Chernigova, Svetlana
A1  - Nardin, Dmitry
T1  - Bacterial Cellulose Nanocomposites: Morphology and Mechanical Properties
JF  - Materials
N2  - Bacterial cellulose (BC) is a promising material for biomedical applications due to its unique properties such as high mechanical strength and biocompatibility. This article describes the microbiological synthesis, modification, and characterization of the obtained BC-nanocomposites originating from symbiotic consortium Medusomyces gisevii. Two BC-modifications have been obtained: BC-Ag and BC-calcium phosphate (BC-Ca3(PO4)2). Structure and physicochemical properties of the BC and its modifications were investigated by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), atomic force microscopy (AFM), and infrared Fourier spectroscopy as well as by measurements of mechanical and water holding/absorbing capacities. Topographic analysis of the surface revealed multicomponent thick fibrils (150–160 nm in diameter and about 15 µm in length) constituted by 50–60 nm nanofibrils weaved into a left-hand helix. Distinctive features of Ca-phosphate-modified BC samples were (a) the presence of 500–700 nm entanglements and (b) inclusions of Ca3(PO4)2 crystals. The samples impregnated with Ag nanoparticles exhibited numerous roundish inclusions, about 110 nm in diameter. The boundaries between the organic and inorganic phases were very distinct in both cases. The Ag-modified samples also showed a prominent waving pattern in the packing of nanofibrils. The obtained BC gel films possessed water-holding capacity of about 62.35 g/g. However, the dried (to a constant mass) BC-films later exhibited a low water absorption capacity (3.82 g/g). It was found that decellularized BC samples had 2.4 times larger Young’s modulus and 2.2 times greater tensile strength as compared to dehydrated native BC films. We presume that this was caused by molecular compaction of the BC structure.
Y1  - 2020
SN  - 1996-1944
U6  - https://doi.org/10.3390/ma13122849
VL  - 13
IS  - 12
SP  - 1
EP  - 16
PB  - MDPI
CY  - Basel
ER  - 
TY  - JOUR
A1  - Digel, Ilya
A1  - Akimbekov, Nuraly S.
A1  - Rogachev, Evgeniy
A1  - Pogorelova, Natalia
T1  - Bacterial cellulose produced by Medusomyces gisevii on glucose and sucrose: biosynthesis and structural properties
JF  - Cellulose
N2  - In this work, the effects of carbon sources and culture media on the production and structural properties of bacterial cellulose (BC) synthesized by Medusomyces gisevii have been studied. The culture medium was composed of different initial concentrations of glucose or sucrose dissolved in 0.4% extract of plain green tea. Parameters of the culture media (titratable acidity, substrate conversion degree etc.) were monitored daily for 20 days of cultivation. The BC pellicles produced on different carbon sources were characterized in terms of biomass yield, crystallinity and morphology by field emission scanning electron microscopy (FE-SEM), atomic force microscopy and X-ray diffraction. Our results showed that Medusomyces gisevii had higher BC yields in media with sugar concentrations close to 10 g L−1 after a 18–20 days incubation period. Glucose in general lead to a higher BC yield (173 g L−1) compared to sucrose (163.5 g L−1). The BC crystallinity degree and surface roughness were higher in the samples synthetized from sucrose. Obtained FE-SEM micrographs show that the BC pellicles synthesized in the sucrose media contained densely packed tangles of cellulose fibrils whereas the BC produced in the glucose media displayed rather linear geometry of the BC fibrils without noticeable aggregates.
KW  - Bacterial cellulose
KW  - Medusomyces gisevi
KW  - Carbon sources
KW  - Culture media
KW  - Cellulose nanostructure
Y1  - 2023
U6  - https://doi.org/10.1007/s10570-023-05592-z
SN  - 1572-882X (Online)
SN  - 0969-0239 (Print)
N1  - Corresponding author: Ilya Digel
PB  - Springer Science + Business Media
CY  - Dordrecht
ER  - 
TY  - JOUR
A1  - Digel, Ilya
A1  - Temiz Artmann, Aysegül
A1  - Nishikawa, K.
A1  - Cook, M.
T1  - Bactericidal effects of plasma-generated cluster ions
JF  - Medical and Biological Engineering and Computing. 43 (2005), H. 6
Y1  - 2005
SN  - 1741-0444
SP  - 800
EP  - 807
ER  - 
TY  - JOUR
A1  - Müller-Veggian, Mattea
A1  - Bochev, B.
A1  - Lieder, R. M.
A1  - Morek, T.
T1  - Band crossing and blocking in side bands of ¹⁸⁰,¹⁸² Os
JF  - Frühjahrstagung ... des Fachausschusses Kernphysik und Hochenergiephysik der DPG (Sektion A: Kernphysik) / Deutsche Physikalische Gesellschaft (1982)
Y1  - 1982
N1  - Verhandlungen der Deutschen Physikalischen Gesellschaft ; 1982=6.R.17,6
SP  - 1273
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Ohler, C.
A1  - Moers, J.
T1  - Band offsets at heavily strained III - V interfaces / C. Ohler ; A. Förster ; J. Moers...
JF  - Journal of Physics D: Applied Physics. 30 (1997), H. 10
Y1  - 1997
SN  - 0022-3727
N1  - ISSN der E-Ausg.: 1361-6463
SP  - 1436
EP  - 1441
ER  - 
TY  - JOUR
A1  - Müller-Veggian, Mattea
A1  - Beuscher, H.
A1  - Neskakis, A
A1  - Gono, Y.
T1  - Band structure in ¹⁹⁰,¹⁹² Au
JF  - Annual report 1977 / Institut für Kernphysik Kernforschungsanlage Jülich
Y1  - 1978
N1  - Spezielle Berichte der Kernforschungsanlage Jülich ; 15
SP  - 46
EP  - 47
PB  - Verlag des Forschungszentrums Jülich
CY  - Jülich
ER  - 
TY  - JOUR
A1  - Müller-Veggian, Mattea
A1  - Beuscher, H.
A1  - Neskakis, A
A1  - Gono, Y.
T1  - Band structure in ¹⁹⁰,¹⁹² Au
JF  - Frühjahrstagung ... des Fachausschusses Kernphysik und Hochenergiephysik der DPG (Sektion A: Kernphysik) / Deutsche Physikalische Gesellschaft (1978)
Y1  - 1978
SP  - 796
PB  - Physik-Verlag
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Müller-Veggian, Mattea
A1  - Neskakis, A.
A1  - Beuscher, H.
A1  - Haenni, D. R.
T1  - Band structure in ¹⁹⁴ Au
JF  - Annual report 1978 / Kernforschungsanlage Jülich Institut für Kernphysik / Hrsg.: A. Fässler. - (Spezielle Berichte der Kernforschungsanlage Jülich ; 36)
Y1  - 1979
SP  - 36
PB  - Kernforschungsanlage
CY  - Jülich
ER  - 
TY  - JOUR
A1  - Förster, Arnold
A1  - Ohler, C.
A1  - Daniels, C.
T1  - Barrier height at clean Au/InAs(100) interfaces / C. Ohler ; C. Daniels ; A. Förster ...
JF  - Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures. 15 (1997), H. 3
Y1  - 1997
SN  - 0169-4332
SP  - 702
EP  - 706
ER  - 
TY  - CHAP
A1  - Bitz, Andreas
A1  - Alaydrus, M.
A1  - Streckert, J.
A1  - Hansen, V.W.
T1  - Base station antennas embedded in complex environments: rf exposure in controlled areas
T2  - 23rd BEMS Annual Meeting, St. Paul, Minnesota, USA, 49-50, June 2001
Y1  - 2001
SP  - 49
EP  - 50
PB  - Bioelectromagnetics Society
CY  - Frederick, MD
ER  - 
TY  - CHAP
A1  - Frantz, Cathy
A1  - Binder, Matthias
A1  - Busch, Konrad
A1  - Ebert, Miriam
A1  - Heinrich, Andreas
A1  - Kaczmarkiewicz, Nadine
A1  - Schlögl-Knothe, Bärbel
A1  - Kunze, Tobias
A1  - Schuhbauer, Christian
A1  - Stetka, Markus
A1  - Schwager, Christian
A1  - Spiegel, Michael
A1  - Teixeira Boura, Cristiano José
A1  - Bauer, Thomas
A1  - Bonk, Alexander
A1  - Eisen, Stefan
A1  - Funck, Bernhard
T1  - Basic Engineering of a High Performance Molten Salt Tower Receiver System
T2  - AIP Conference Proceedings
N2  - The production of dispatchable renewable energy will be one of the most important key factors of the future energy supply. Concentrated solar power (CSP) plants operated with molten salt as heat transfer and storage media are one opportunity to meet this challenge. Due to the high concentration factor of the solar tower technology the maximum process temperature can be further increased which ultimately decreases the levelized costs of electricity of the technology (LCOE). The development of an improved tubular molten salt receiver for the next generation of molten salt solar tower plants is the aim of this work. The receiver is designed for a receiver outlet temperature up to 600 °C. Together with a complete molten salt system, the receiver will be integrated into the Multi-Focus-Tower (MFT) in Jülich (Germany). The paper describes the basic engineering of the receiver, the molten salt tower system and a laboratory corrosion setup.
Y1  - 2020
U6  - https://doi.org/10.1063/5.0085895
N1  - SOLARPACES 2020: 26th International Conference on Concentrating Solar Power and Chemical Energy Systems, 28 September – 2 October 2020, Freiburg, Germany
SP  - 1
EP  - 10
ER  - 
TY  - JOUR
A1  - Zastrow, Udo
T1  - Basic geometrical singularities in plane-elasticity and plate-bending problems
JF  - International Journal of Solids and Structures. 21 (1985), H. 10
Y1  - 1985
SN  - 0020-7683
SP  - 1047
EP  - 1067
ER  - 
TY  - CHAP
A1  - Abbas, Karim
A1  - Thurn, Laura
A1  - Kessler, Julia
A1  - Eichler, Fabian
T1  - Basic research of the consideration of additive manufactured lattice structures under thermoand fluid dynamic loads
T2  - Modern technologies in manufacturing (MTeM 2019)
Y1  - 2019
U6  - https://doi.org/10.1051/matecconf/201929901009
N1  - MATEC Web of Conferences 299; MTeM 2019
VL  - 299
IS  - Article 01009
ER  - 
TY  - CHAP
A1  - Kessler, Julia
A1  - Balc, Nicolae
A1  - Gebhardt, Andreas
A1  - Abbas, Karim
T1  - Basic research on lattice structures focused on the reliance of the cross sectional area and additional coatings
T2  - The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 – CoSME’16
Y1  - 2017
U6  - https://doi.org/10.1051/matecconf/20179403008
N1  - MATEC Web Conf. Vol 94, 2017, 03008
MATEC Web of Conferences 94, 03008 (2017)
ET  - Vol. 94
ER  - 
TY  - CHAP
A1  - Kessler, Julia
A1  - Balc, Nicolae
A1  - Gebhardt, Andreas
T1  - Basic research on lattice structures focused on the strut shape and welding beads
T2  - Physics Procedia
Y1  - 2016
U6  - https://doi.org/10.1016/j.phpro.2016.08.086
SN  - 1875-3884
N1  - Laser Assisted Net Shape Engineering 
9th International Conference on Photonic Technologies Proceedings of the LANE 2016
VL  - Vol. 83
SP  - 833
EP  - 838
ER  - 
TY  - JOUR
A1  - Kessler, Julia
A1  - Balc, Nicolae
A1  - Gebhardt, Andreas
A1  - Abbas, Karim
T1  - Basic Research on Lattice Structures Focused on the Tensile Strength
JF  - Applied Mechanics and Materials
Y1  - 2015
U6  - https://doi.org/10.4028/www.scientific.net/AMM.808.193
SN  - 1662-7482
N1  - MTeM ; October 14-16, 2015, Cluj-Napoca, Romania
VL  - Vol. 808
SP  - 193
EP  - 198
PB  - Trans Tech Publications
CY  - Bäch
ER  - 
TY  - JOUR
A1  - Selmer, Thorsten
A1  - Jennemann, Richard
A1  - Bauer, Bernhard L.
A1  - Bertalanffy, Helmut
T1  - Basidiolipids from Agaricus are novel immune adjuvants / Jennemann, R. ; Bauer, BL. ; Bertalanffy, H. ; Selmer, T. ; Wiegandt, H.
JF  - Immunobiology. 200 (1999), H. 2
Y1  - 1999
SN  - 0171-2985
N1  - PMID: 10416134
SP  - 277
EP  - 289
ER  - 
TY  - JOUR
A1  - Staat, Manfred
T1  - Basis Reduction for the Shakedown Problem for Bounded Kinematic Hardening Material
N2  - Limit and shakedown analysis are effective methods for assessing the load carrying capacity of a given structure. The elasto–plastic behavior of the structure subjected to loads varying in a given load domain is characterized by the shakedown load factor, defined as the maximum factor which satisfies the sufficient conditions stated in the corresponding static shakedown theorem. The finite element dicretization of the problem may lead to very large convex optimization. For the effective solution a basis reduction method has been developed that makes use of the special problem structure for perfectly plastic material. The paper proposes a modified basis reduction method for direct application to the two-surface plasticity model of bounded kinematic hardening material. The considered numerical examples show an enlargement of the load carrying capacity due to bounded hardening.
KW  - Finite-Elemente-Methode
KW  - Einspielen <Werkstoff>
KW  - Basis Reduktion
KW  - konvexe Optimierung
KW  - FEM
KW  - Druckgeräte
KW  - Basis reduction
KW  - Convex optimization
KW  - FEM
KW  - Shakedown analysis
Y1  - 2000
ER  - 
TY  - CHAP
A1  - Staat, Manfred
A1  - Heitzer, M.
T1  - Basis reduction technique for limit and shakedown problems
T2  - Numerical Methods for Limit and Shakedown Analysis. Deterministic and Probabilistic Approach. NIC Series Vol. 15 / Ed. by Staat, M.; Heitzer, M.
Y1  - 2003
U6  - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:0001-2018112115
SN  - 3-00-010001-6
SP  - 1
EP  - 55
PB  - John von Neumann Institute for Computing (NIC)
CY  - Jülich
ER  - 
TY  - JOUR
A1  - Biselli, Manfred
A1  - Thömmes, J.
A1  - Kula, M.-R.
A1  - Wandrey, Christian
T1  - Batch kinetic data of hybridoma growth and productivity as a basis for the simulation of antibody production in various culture systems /  Thömmes, J. ; Biselli, M. ; Kula, M.-R. ; Wandrey, C.
JF  - Animal cell technology : products of today, prospects for tomorrow ; ESACT, European Society for Animal Cell Technology, the 12th meeting / Ed. R. E. Spier
Y1  - 1994
SN  - 0750618450
N1  - Meeting / European Society for Animal Cell Technology ; 12
SP  - 513
EP  - 517
PB  - Butterworth-Heinemann
CY  - Oxford
ER  - 
TY  - JOUR
A1  - Buniatyan, V.
A1  - Huck, Christina
A1  - Poghossian, Arshak
A1  - Aroutiounian, V. M.
A1  - Schöning, Michael Josef
T1  - BaxSr1-x TiO3/pc-Si heterojunction
JF  - Armenian journal of physics
Y1  - 2013
SN  - 1829-1171
VL  - 6
IS  - 4
SP  - 177
EP  - 187
PB  - National Academy of Sciences of Armenia
CY  - Yerevan
ER  - 
TY  - JOUR
A1  - Buniatyan, V.
A1  - Huck, Christina
A1  - Poghossian, Arshak
A1  - Aroutiounian, V. M.
A1  - Schöning, Michael Josef
T1  - BaxSr1-x TiO3/pc-Si heterojunction capacitance
JF  - Armenian journal of physics
Y1  - 2013
SN  - 1829-1171
VL  - 6
IS  - 4
SP  - 188
EP  - 197
PB  - National Academy of Sciences of Armenia
CY  - Yerevan
ER  - 
TY  - JOUR
A1  - Biener, Ernst
A1  - Rouvé, G.
T1  - Behaviour and maintenance of some old masonry gravity dams
JF  - Safety of dams : proceedings of the International Conference on Safety of Dams, Coimbra, 23-28 April 1984 / ed. by J. Laginha Serafim. - [Hauptbd.]
Y1  - 1984
SN  - 90-6191-522-8
N1  - International Conference on Safety of Dams <1984, Coimbra> ; ISBN Set: 90-6191-521-X
SP  - 101
EP  - 106
PB  - Rotterdam [u.a.]
CY  - Balkema
ER  - 
TY  - CHAP
A1  - Morandi, Paolo
A1  - Butenweg, Christoph
A1  - Breis, Khaled
A1  - Beyer, Katrin
A1  - Magenes, Guido
ED  - Arion, Cristian
ED  - Scupin, Alexandra
ED  - Ţigănescu, Alexandru
T1  - Behaviour factor q for the seismic design of URM buildings
T2  - The Third European Conference on Earthquake Engineering and Seismology
N2  - Recent earthquakes showed that low-rise URM buildings following codecompliant seismic design and details behaved in general very well without substantial damages. Although advances in simulation tools make nonlinear calculation methods more readily accessible to designers, linear analyses will still be the standard design method for years to come. The present paper aims to improve the linear seismic design method by providing a proper definition of the q-factor of URM buildings. Values of q-factors are derived for low-rise URM buildings with rigid diaphragms, with reference to modern structural configurations realized in low to moderate seismic areas of Italy and Germany. The behaviour factor components for deformation and energy dissipation capacity and for overstrength due to the redistribution of forces are derived by means of pushover analyses. As a result of the investigations, rationally based values of the behaviour factor q to be used in linear analyses in the range of 2.0 to 3.0 are proposed.
KW  - unreinforced masonry buildings
KW  - modern constructions
KW  - seismic design
KW  - linear elastic analysis;
KW  - behaviour factor q
Y1  - 2022
SN  - 978-973-100-533-1
N1  - 3ECEES - Third European Conference on Earthquake Engineering and Seismology, September 4 – September 9, 2022, Bucharest
SP  - 1184
EP  - 1194
ER  - 
TY  - JOUR
A1  - Gspandl, Stephan
A1  - Pill, Ingo
A1  - Reip, Michael
A1  - Steinbauer, Gerald
A1  - Ferrein, Alexander
T1  - Belief Management for High-Level Robot Programs
JF  - Proceedings of the Twenty-Second International Joint Conference on Artificial Intelligence [electronic resource] : Barcelona, Catalonia, Spain, 16 - 22 July 2011 / sponsored by International Joint Conferences on Artificial Intelligence (IJCAI) and the Association for the Advancement of Artificial Intelligence (AAAI). Ed. by Toby Walsh
Y1  - 2011
N1  - International Joint Conference on Artificial Intelligence ; (22 : ; 2011.07.16-22 : ; Barcelona, Spain) ; IJCAI ; (22 : ; 2011.07.16-22 : ; Barcelona, Spain)
SP  - 900
EP  - 905
ER  - 
TY  - JOUR
A1  - Rens, Gavin
A1  - Ferrein, Alexander
T1  - Belief-node condensation for online POMDP algorithms
N2  - Slightly extended version of the paper accepted at the Robotics and Artificial Intelligence Workshop, a special track of IEEE AFRICON-2013, held in Mauritius, 9-12 September 2013
Y1  - 2013
SP  - 1
EP  - 7
PB  - IEEE
CY  - New York
ER  - 
TY  - JOUR
A1  - Schulte-Tigges, Joschua
A1  - Förster, Marco
A1  - Nikolovski, Gjorgji
A1  - Reke, Michael
A1  - Ferrein, Alexander
A1  - Kaszner, Daniel
A1  - Matheis, Dominik
A1  - Walter, Thomas
T1  - Benchmarking of various LiDAR sensors for use in self-driving vehicles in real-world environments
JF  - Sensors
N2  - Abstract
In this paper, we report on our benchmark results of the LiDAR sensors Livox Horizon, Robosense M1, Blickfeld Cube, Blickfeld Cube Range, Velodyne Velarray H800, and Innoviz Pro. The idea was to test the sensors in different typical scenarios that were defined with real-world use cases in mind, in order to find a sensor that meet the requirements of self-driving vehicles. For this, we defined static and dynamic benchmark scenarios. In the static scenarios, both LiDAR and the detection target do not move during the measurement. In dynamic scenarios, the LiDAR sensor was mounted on the vehicle which was driving toward the detection target. We tested all mentioned LiDAR sensors in both scenarios, show the results regarding the detection accuracy of the targets, and discuss their usefulness for deployment in self-driving cars.
KW  - Lidar
KW  - Benchmark
KW  - Self-driving
Y1  - 2022
U6  - https://doi.org/10.3390/s22197146
SN  - 1424-8220
N1  - This article belongs to the Special Issue "Sensor Fusion for Vehicles Navigation and Robotic Systems"
VL  - 22
IS  - 19
PB  - MDPI
CY  - Basel
ER  - 
TY  - JOUR
A1  - Burger, René
A1  - Lindner, Simon
A1  - Rumpf, Jessica
A1  - Do, Xuan Tung
A1  - Diehl, Bernd W.K.
A1  - Rehahn, Matthias
A1  - Monakhova, Yulia
A1  - Schulze, Margit
T1  - Benchtop versus high field NMR: Comparable performance found for the molecular weight determination of lignin
JF  - Journal of Pharmaceutical and Biomedical Analysis
N2  - Lignin is a promising renewable biopolymer being investigated worldwide as an environmentally benign substitute of fossil-based aromatic compounds, e.g. for the use as an excipient with antioxidant and antimicrobial properties in drug delivery or even as active compound. For its successful implementation into process streams, a quick, easy, and reliable method is needed for its molecular weight determination. Here we present a method using 1H spectra of benchtop as well as conventional NMR systems in combination with multivariate data analysis, to determine lignin’s molecular weight (Mw and Mn) and polydispersity index (PDI). A set of 36 organosolv lignin samples (from Miscanthus x giganteus, Paulownia tomentosa and Silphium perfoliatum) was used for the calibration and cross validation, and 17 samples were used as external validation set. Validation errors between 5.6% and 12.9% were achieved for all parameters on all NMR devices (43, 60, 500 and 600 MHz). Surprisingly, no significant difference in the performance of the benchtop and high-field devices was found. This facilitates the application of this method for determining lignin’s molecular weight in an industrial environment because of the low maintenance expenditure, small footprint, ruggedness, and low cost of permanent magnet benchtop NMR systems.
KW  - NMR
KW  - PLS-regression
KW  - Molecular weight determination
KW  - Chemometrics
KW  - Biomass
Y1  - 2022
SN  - 0731-7085
U6  - https://doi.org/10.1016/j.jpba.2022.114649
VL  - 212
IS  - Article number: 114649
PB  - Elsevier
CY  - New York, NY
ER  - 
TY  - CHAP
A1  - Schneider, Dominik
A1  - Wisselink, Frank
A1  - Czarnecki, Christian
A1  - Nölle, Nikolai
T1  - Benefits and framework conditions for information-driven business models concerning the Internet of Things
T2  - Digitalization in companies
N2  - In the context of the increasing digitalization, the Internet of Things (IoT) is seen as a technological driver through which completely new business models can emerge in the interaction of different players. Identified key players include traditional industrial companies, municipalities and telecommunications companies. The latter, by providing connectivity, ensure that small devices with tiny batteries can be connected almost anywhere and directly to the Internet. There are already many IoT use cases on the market that provide simplification for end users, such as Philips Hue Tap. In addition to business models based on connectivity, there is great potential for information-driven business models that can support or enhance existing business models. One example is the IoT use case Park and Joy, which uses sensors to connect parking spaces and inform drivers about available parking spaces in real time. Information-driven business models can be based on data generated in IoT use cases. For example, a telecommunications company can add value by deriving more decision-relevant information – called insights – from data that is used to increase decision agility. In addition, insights can be monetized. The monetization of insights can only be sustainable, if careful attention is taken and frameworks are considered. In this chapter, the concept of information-driven business models is explained and illustrated with the concrete use case Park and Joy. In addition, the benefits, risks and framework conditions are discussed.
Y1  - 2024
SN  - 978-3-658-39093-8 (Print)
SN  - 978-3-658-39094-5 (eBook)
U6  - https://doi.org/10.1007/978-3-658-39094-5_5
SP  - 59
EP  - 75
PB  - Springer
CY  - Wiesbaden
ER  -