TY - JOUR A1 - Finger, Felix A1 - Braun, Carsten A1 - Bil, Cees T1 - Impact of electric propulsion technology and mission requirements on the performance of VTOL UAVs JF - CEAS Aeronautical Journal N2 - One of the engineering challenges in aviation is the design of transitioning vertical take-off and landing (VTOL) aircraft. Thrust-borne flight implies a higher mass fraction of the propulsion system, as well as much increased energy consumption in the take-off and landing phases. This mass increase is typically higher for aircraft with a separate lift propulsion system than for aircraft that use the cruise propulsion system to support a dedicated lift system. However, for a cost–benefit trade study, it is necessary to quantify the impact the VTOL requirement and propulsion configuration has on aircraft mass and size. For this reason, sizing studies are conducted. This paper explores the impact of considering a supplemental electric propulsion system for achieving hovering flight. Key variables in this study, apart from the lift system configuration, are the rotor disk loading and hover flight time, as well as the electrical systems technology level for both batteries and motors. Payload and endurance are typically used as the measures of merit for unmanned aircraft that carry electro-optical sensors, and therefore the analysis focuses on these particular parameters. Y1 - 2018 U6 - http://dx.doi.org/10.1007/s13272-018-0352-x SN - 1869-5582 print SN - 1869-5590 online VL - 10 IS - 3 SP - 843 PB - Springer ER - TY - CHAP A1 - Finger, Felix A1 - Braun, Carsten A1 - Bil, Cees T1 - Impact of Engine Failure Constraints on the Initial Sizing of Hybrid-Electric GA Aircraft T2 - AIAA Scitech 2019 Forum Y1 - 2019 U6 - http://dx.doi.org/10.2514/6.2019-1812 N1 - AIAA Scitech Forum, 2019; San Diego; United States; 7 January 2019 through 11 January 2019 ER - TY - JOUR A1 - Dachwald, Bernd A1 - McDonald, Malcolm A1 - McInnes, Colin R. A1 - Mengali, Giovanni T1 - Impact of Optical Degradation on Solar Sail Mission Performance JF - Journal of Spacecraft and Rockets. 44 (2007), H. 4 Y1 - 2007 SN - 0022-4650 N1 - 2. ISSN: 1533-6794 SP - 740 EP - 749 ER - TY - CHAP A1 - Ludowicy, Jonas A1 - Rings, René A1 - Finger, Felix A1 - Braun, Carsten A1 - Bil, Cees T1 - Impact of Propulsion Technology Levels on the Sizing and Energy Consumption for Serial HybridElectric General Aviation Aircraft T2 - Asia Pacific International Symposium on Aerospace Technology. APISAT 2019 Y1 - 2019 ER - TY - JOUR A1 - Götten, Falk A1 - Havermann, Marc A1 - Braun, Carsten A1 - Marino, Matthew A1 - Bil, Cees T1 - Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections JF - Journal of Aircraft N2 - The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body’s fineness ratio and cross section. The drag forces are normalized with the respective body’s wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies’ cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature. Y1 - 2020 U6 - http://dx.doi.org/10.2514/1.C036032 SN - 1533-3868 SP - 1 EP - 13 PB - AIAA CY - Reston, Va. ER - TY - JOUR A1 - Lettini, Antonio A1 - Havermann, Marc A1 - Guidetti, Marco A1 - Fornaciari, Andrea T1 - Improved functionalities and energy saving potential on mobile machines combining electronics with flow sharing valve and variable displacement pump JF - IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010 Y1 - 2010 SN - 978-3-940565-92-1 N1 - IFK, 7, Internationales Fluidtechnisches Kolloquium, 7., Aachen, DE, 2010-03-22 - 2010-03-24 SP - 103 EP - 114 PB - - ER - TY - JOUR A1 - Haj Ayed, A. A1 - Kusterer, K. A1 - Funke, Harald A1 - Keinz, Jan A1 - Striegan, Constantin A1 - Bohn, D. T1 - Improvement study for the dry-low-NOx hydrogen micromix combustion technology JF - Propulsion and power research Y1 - 2015 U6 - http://dx.doi.org/10.1016/j.jppr.2015.07.003 SN - 2212-540X VL - Vol. 4 IS - Iss. 3 SP - 132 EP - 140 ER - TY - CHAP A1 - Thoma, Andreas A1 - Fisher, Alex A1 - Braun, Carsten T1 - Improving the px4 avoid algorithm by bio-inspired flight strategies T2 - DLRK2020 - „Luft- und Raumfahrt – Verantwortung in allen Dimensionen“ Y1 - 2020 N1 - Deutscher Luft- und Raumfahrtkongress 2020, 1. bis 3. September 2020 – Online, „Luft- und Raumfahrt – Verantwortung in allen Dimensionen“ ER - TY - CHAP A1 - Neu, Eugen A1 - Janser, Frank A1 - Khatibi, Akbar A. A1 - Orifici, Adrian C. T1 - In-flight vibration-based structural health monitoring of aircraft wings T2 - 30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea N2 - This work presents a methodology for automated damage-sensitive feature extraction and anomaly detection under multivariate operational variability for in-flight assessment of wings. The method uses a passive excitation approach, i. e. without the need for artificial actuation. The modal system properties (natural frequencies and damping ratios) are used as damage-sensitive features. Special emphasis is placed on the use of Fiber Bragg Grating (FBG) sensing technology and the consideration of Operational and Environmental Variability (OEV). Measurements from a wind tunnel investigation with a composite cantilever equipped with FBG and piezoelectric sensors are used to successfully detect an impact damage. In addition, the feasibility of damage localisation and severity estimation is evaluated based on the coupling found between damageand OEV-induced feature changes. Y1 - 2016 ER - TY - CHAP A1 - Thenent, N. E. A1 - Dahmann, Peter T1 - Increasing aircraft design flexibility ‐ The development of a hydrostatic transmission for gliders with self‐launching capability T2 - Deutscher Luft- und Raumfahrtkongress 2011 : Bremen, 27. bis 29. September 2011 ; Tagungsband Y1 - 2011 SN - 978-3-9321-8274-7 SP - 865 EP - 883 PB - Dt. Gesellschaft für Luft- und Raumfahrt CY - Bonn ER - TY - CHAP A1 - Hoefling, J. A1 - Schirra, Julian A1 - Spohr, A. A1 - Schäfer, D. T1 - Induced drag computation with wake model schemes for highly non-planar wing systems T2 - Deutscher Luft- und Raumfahrtkongress 2013 : 10.9. - 12.9.2013, Stuttgart Y1 - 2013 SP - 1 EP - 10 PB - Dt. Ges. für Luft- und Raumfahrt CY - Bonn ER - TY - JOUR A1 - Bullerschen, Klaus-Gerd A1 - Wilhelmi, Herbert A1 - Wimmer, W. T1 - Influence of non-uniform material properties and water cooling on current density and temperature profiles in arc furnace elektrodes JF - Steel Research. 56 (1985), H. 11 Y1 - 1985 SN - 0177-4832 SP - 559 EP - 564 ER - TY - JOUR A1 - Havermann, Marc A1 - Kainuma, M. A1 - Takayama, K. T1 - Influence of Physical and Geometrical Parameters on Vortex Rings Generated by a Shock Tube / Havermann, M. ; Kainuma, M. ; Takayama, K. JF - Non-lethal options enhancing security and stability : 3rd European Symposium on Non-Lethal Weapons, May 10 - 12, 2005, Ettlingen, Germany / ICT, Fraunhofer-Institut Chemische Technologie; European Working Group Non-Lethal Weapons Y1 - 2005 N1 - European Symposium on Non-Lethal Weapons ; (3 ; 2005.5.10-12 ; Ettlingen); V 24 PB - ICT CY - Pfinztal ER - TY - CHAP A1 - Finger, Felix A1 - Götten, Falk A1 - Braun, Carsten T1 - Initial Sizing for a Family of Hybrid-Electric VTOL General Aviation Aircraft T2 - 67. Deutscher Luft- und Raumfahrtkongress 2018 Y1 - 2018 ER - TY - JOUR A1 - Finger, Felix A1 - Bil, Cees A1 - Braun, Carsten T1 - Initial Sizing Methodology for Hybrid-Electric General Aviation Aircraft JF - Journal of Aircraft Y1 - 2019 U6 - http://dx.doi.org/10.2514/1.C035428 SN - 1533-3868 VL - 57 IS - 2 SP - 245 EP - 255 ER - TY - BOOK A1 - Janser, Frank A1 - Havermann, Marc A1 - Hoeveler, Bastian A1 - Hertz, Cyril T1 - Inkompressible Profil- und Tragflügelaerodynamik T3 - Strömungslehre und Aerodynamik ; Band 2 Y1 - 2016 SN - 978-3-8107-0261-6 N1 - Signatur in der Bibliothek: 21 ZSE 118 PB - Verlagshaus Mainz GmbH CY - Aachen ET - 1. Auflage ER - TY - BOOK A1 - Janser, Frank A1 - Havermann, Marc T1 - Inkompressible Strömungen Y1 - 2012 SN - 978-3-86130-446-3 N1 - Strömungslehre und Aerodynamik PB - Mainz CY - Aachen ER - TY - BOOK A1 - Janser, Frank A1 - Havermann, Marc T1 - Inkompressible Strömungen Y1 - 2015 SN - 978-3-86130-446-3 N1 - Strömungslehre und Aerodynamik ; 1 PB - Verlagshaus Mainz GmbH CY - Aachen ET - 3. Aufl. ER - TY - CHAP A1 - Huth, Thomas A1 - Elsen, Olaf A1 - Hartwig, Christoph A1 - Esch, Thomas T1 - Innovative modular valve trains for 2015 - logistic benefits by EMVT T2 - IFAC Proceedings Volumes, Volume 39, Issue 3 N2 - In this paper the way to a 5-day-car with respect to a modular valve train systems for spark ignited combustion engines is shown. The necessary product diversity is shift from mechanical or physical components to software components. Therefore, significant improvements of logistic indicators are expected and shown. The working principle of a camless cylinder head with respect to an electromagnetical valve train (EMVT) is explained and it is demonstrated that shifting physical diversity to software is feasible. The future design of combustion engine systems including customisation can be supported by a set of assistance tools which is shown exemplary. Y1 - 2006 U6 - http://dx.doi.org/10.3182/20060517-3-FR-2903.00172 N1 - Part of special issue "12th IFAC Symposium on Information Control Problems in Manufacturing" SP - 315 EP - 320 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Röth, Thilo A1 - Tragsdorf, Carsten T1 - Innovativer Einsatz von Werkstoffen - Trends und Entwicklungen im Karosserieleichtbau N2 - 1) In Karosseriestrukturen steht der richtige Werkstoffeinsatz stärker den je im Spannungsfeld von Leichtbau, Kosten (Stückzahlen) und Leistungsanforderung 2) In „klassischen“ Strukturen von Modulträgern und Klappen hat sich die Materialmischbauweise verstärkt in den letzten Jahren durchgesetzt 3) Unter Aspekten des konzeptionellen Leichtbaus erscheint der verstärkte Einsatz von Leichtbauwerkstoffen im Vorderwagen sowie in der Dachstruktur zielführend 4) Offene Strukturprofile in Materialmischbauweise liefern für eine Vielzahl von Anwendungen ein interessantes und bis dato kaum genutztes Potential 5) Neue Entwicklungen bei den Fügetechnologien (i.b. kontinuierliche Fügeverbindungen und kombinierte Verfahren) unterstützen den wirtschaftlichen Karosserieleichtbau 6) Werkstoffinnovationen sowie neuartige Fertigungsverfahren machen den Konstruktionswerkstoff „Stahl“ auch in der Zukunft im Karosseriebau weiterhin sehr attraktiv KW - Karosseriebau KW - Leichtbau KW - Karosserieleichtbau KW - Materialmischbauweise KW - Leichtbauwerkstoffe Y1 - 2004 ER - TY - BOOK A1 - Mertens, Josef T1 - Instationäre Strömungen von Gasen mit brennbaren Partikeln Y1 - 1983 N1 - Aachen, Techn. Hochschule, Diss., 1983 CY - Aachen ER - TY - JOUR A1 - Schmitz, Günter A1 - Bartz, R. A1 - Hilger, U. A1 - Siedentop, M. T1 - Intelligent Alcohol Fuel Sensor Y1 - 1990 N1 - SAE- Paper-No.: 900231, SAE International Congress and Exposition, Detroit, Feb. 26 - March 2, 1990 ER - TY - JOUR A1 - Mertens, Josef A1 - Kelm, R. A1 - Velden, A. van der T1 - Interdisziplinäre Auslegung eines Verkehrsflugzeugflügels JF - DGLR-Jahrbuch 1999 Bd. 3 Y1 - 1999 N1 - DGLR-JT99-156 SP - 1605 EP - 1610 ER - TY - BOOK A1 - Ley, Wilfried T1 - Internationale Raumstation : Konfiguration, Betrieb und Nutzung ; Gemeinschaftsveranstaltung der FH Aachen, der DGLR und des DLR / 11. Raumfahrt-Kolloquium an der Fachhochschule Aachen, 26. November 1998. / Ley, Wilfried [Hrsg.] Y1 - 1998 SN - 3-932182-04-9 PB - DGLR CY - Bonn ER - TY - JOUR A1 - Dachwald, Bernd T1 - Interplanetary Mission Analysis for Non-Perfectly Reflecting Solar Sailcraft Using Evolutionary Neurocontrol JF - Astrodynamics 2003 : proceedings of the AAS/AIAA Astrodynamics Conference held August 3 - 7, 2003, Big Sky, Montana / ed. by Jean de Lafontaine. - Pt. 2. - (Advances in the astronautical sciences ; 116,2) Y1 - 2004 SN - 0-87703-509-1 N1 - Astrodynamics Conference <2003, Big Sky, Mont.> ; American Institute of Aeronautics and Astronautics ; AAS-03-579 SP - 1247 EP - 1262 PB - Univelt CY - San Diego, Calif. ER - TY - CHAP A1 - Spurmann, Jörn A1 - Ohndorf, Andreas A1 - Dachwald, Bernd A1 - Seboldt, Wolfgang A1 - Löb, Horst A1 - Schartner, Karl-Heinz T1 - Interplanetary trajectory optimization for a sep mission to Saturn T2 - 60th International Astronautical Congress 2009 N2 - The recently proposed NASA and ESA missions to Saturn and Jupiter pose difficult tasks to mission designers because chemical propulsion scenarios are not capable of transferring heavy spacecraft into the outer solar system without the use of gravity assists. Thus our developed mission scenario based on the joint NASA/ESA Titan Saturn System Mission baselines solar electric propulsion to improve mission flexibility and transfer time. For the calculation of near-globally optimal low-thrust trajectories, we have used a method called Evolutionary Neurocontrol, which is implemented in the low-thrust trajectory optimization software InTrance. The studied solar electric propulsion scenario covers trajectory optimization of the interplanetary transfer including variations of the spacecraft's thrust level, the thrust unit's specific impulse and the solar power generator power level. Additionally developed software extensions enabled trajectory optimization with launcher-provided hyperbolic excess energy, a complex solar power generator model and a variable specific impulse ion engine model. For the investigated mission scenario, Evolutionary Neurocontrol yields good optimization results, which also hold valid for the more elaborate spacecraft models. Compared to Cassini/Huygens, the best found solutions have faster transfer times and a higher mission flexibility in general. KW - Spacecraft KW - Reusable Rocket Engines KW - Hybrid Propellants Y1 - 2009 SN - 9781615679089 N1 - 60th International Astronautical Congress 2009 (IAC 2009) Held 12-16 October 2009, Daejeon, Republic of Korea. SP - 5234 EP - 5248 ER - TY - JOUR A1 - Loeb, Horst Wolfgang A1 - Schartner, Karl-Heinz A1 - Dachwald, Bernd A1 - Ohndorf, Andreas A1 - Seboldt, Wolfgang T1 - Interstellar heliopause probe JF - Труды МАИ N2 - There is common agreement within the scientific community that in order to understand our local galactic environment it will be necessary to send a spacecraft into the region beyond the solar wind termination shock. Considering distances of 200 AU for a new mission, one needs a spacecraft traveling at a speed of close to 10 AU/yr in order to keep the mission duration in the range of less than 25 yrs, a transfer time postulated by European Space Agency (ESA). Two propulsion options for the mission have been proposed and discussed so far: the solar sail propulsion and the ballistic/radioisotope-electric propulsion (REP). As a further alternative, we here investigate a combination of solar-electric propulsion (SEP) and REP. The SEP stage consists of six 22-cms diameter RIT-22 ion thrusters working with a high specific impulse of 7377 s corresponding to a positive grid voltage of 5 kV. Solar power of 53 kW at begin of mission (BOM) is provided by a lightweight solar array. Y1 - 2012 IS - 60 SP - 2 EP - 2 PB - Moskauer Staatliches Luftfahrtinstitut (МАИ) CY - Moskau ER - TY - JOUR A1 - Hein, Andreas M. A1 - Eubanks, T. Marshall A1 - Hibberd, Adam A1 - Fries, Dan A1 - Schneider, Jean A1 - Lingam, Manasvi A1 - Kennedy, Robert A1 - Perakis, Nikolaos A1 - Dachwald, Bernd A1 - Kervella, Pierre T1 - Interstellar Now! Missions to and sample returns from nearby interstellar objects N2 - The recently discovered first high velocity hyperbolic objects passing through the Solar System, 1I/'Oumuamua and 2I/Borisov, have raised the question about near term missions to Interstellar Objects. In situ spacecraft exploration of these objects will allow the direct determination of both their structure and their chemical and isotopic composition, enabling an entirely new way of studying small bodies from outside our solar system. In this paper, we map various Interstellar Object classes to mission types, demonstrating that missions to a range of Interstellar Object classes are feasible, using existing or near-term technology. We describe flyby, rendezvous and sample return missions to interstellar objects, showing various ways to explore these bodies characterizing their surface, dynamics, structure and composition. Interstellar objects likely formed very far from the solar system in both time and space; their direct exploration will constrain their formation and history, situating them within the dynamical and chemical evolution of the Galaxy. These mission types also provide the opportunity to explore solar system bodies and perform measurements in the far outer solar system. Y1 - 2020 SP - 1 EP - 8 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Hein, Andreas M. A1 - Eubanks, T. Marshall A1 - Lingam, Manasvi A1 - Hibberd, Adam A1 - Fries, Dan A1 - Schneider, Jean A1 - Kervella, Pierre A1 - Kennedy, Robert A1 - Perakis, Nikolaos A1 - Dachwald, Bernd T1 - Interstellar now! Missions to explore nearby interstellar objects JF - Advances in Space Research N2 - The recently discovered first hyperbolic objects passing through the Solar System, 1I/’Oumuamua and 2I/Borisov, have raised the question about near term missions to Interstellar Objects. In situ spacecraft exploration of these objects will allow the direct determination of both their structure and their chemical and isotopic composition, enabling an entirely new way of studying small bodies from outside our solar system. In this paper, we map various Interstellar Object classes to mission types, demonstrating that missions to a range of Interstellar Object classes are feasible, using existing or near-term technology. We describe flyby, rendezvous and sample return missions to interstellar objects, showing various ways to explore these bodies characterizing their surface, dynamics, structure and composition. Their direct exploration will constrain their formation and history, situating them within the dynamical and chemical evolution of the Galaxy. These mission types also provide the opportunity to explore solar system bodies and perform measurements in the far outer solar system. KW - Interstellar objects KW - Trajectories KW - Missions Y1 - 2022 U6 - http://dx.doi.org/10.1016/j.asr.2021.06.052 SN - 0273-1177 VL - 69 IS - 1 SP - 402 EP - 414 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Weiss, Alexander A1 - Abanteriba, Sylvester A1 - Esch, Thomas T1 - Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow T2 - Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B N2 - Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations. Y1 - 2007 SN - 0-7918-4288-6 U6 - http://dx.doi.org/10.1115/FEDSM2007-37387 N1 - Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B. San Diego, California, USA. July 30–August 2, 2007 SP - 1861 EP - 1871 PB - American Society of Mechanical Engineers (ASME) CY - New York ER - TY - JOUR A1 - Havermann, Marc A1 - Moeglin, J.-P. T1 - ISL's Research on Systems with Controlled Effects for Non-Lethal Applications / Moeglin, J.-P. ; Havermann, M. et al. JF - Non-lethal options enhancing security and stability : 3rd European Symposium on Non-Lethal Weapons, May 10 - 12, 2005, Ettlingen, Germany / ICT, Fraunhofer-Institut Chemische Technologie; European Working Group Non-Lethal Weapons Y1 - 2005 N1 - European Symposium on Non-Lethal Weapons ; (3 ; 2005.5.10-12 ; Ettlingen); P 35 PB - ICT CY - Pfinztal ER - TY - PAT A1 - Salber, Wolfgang A1 - Pischinger, Martin A1 - Esch, Thomas A1 - Hagen, Jürgen T1 - Kaltstartverfahren für eine drosselfreie Mehrzylinder-Kolbenbrennkraftmaschine N2 - Die Erfindung betrifft ein Kaltstartverfahren für eine Mehrzylinder-Kolbenbrennkraftmaschine mit Anlasser und einer Motorsteuerung zur Ansteuerung von Kraftstoffeinspritzeinrichtungen, Zündung und voll variabel elektromagnetisch betätigbaren Gaswechselventilen an den einzelnen Zylindern, bei dem die Kurbelwelle über den Anlasser gedreht wird und zum Start für wenigstens einen Zylinder die dazugehörigen Gaswechselventile, die Kraftstoffeinspritzeinrichtung und die Zündung in einem vorgegebenen Taktzyklus angesteuert werden und zwar in den ersten Arbeitszyklen mit "Spätem Einlaß Öffnen". Y1 - 2000 N1 - Patent DE000019830974B4 2005.11.03 ER - TY - JOUR A1 - Dachwald, Bernd A1 - Ulamec, Stephan A1 - Postberg, Frank A1 - Sohl, Frank A1 - Vera, Jean-Pierre de A1 - Christoph, Waldmann A1 - Lorenz, Ralph D. A1 - Hellard, Hugo A1 - Biele, Jens A1 - Rettberg, Petra T1 - Key technologies and instrumentation for subsurface exploration of ocean worlds JF - Space Science Reviews N2 - In this chapter, the key technologies and the instrumentation required for the subsurface exploration of ocean worlds are discussed. The focus is laid on Jupiter’s moon Europa and Saturn’s moon Enceladus because they have the highest potential for such missions in the near future. The exploration of their oceans requires landing on the surface, penetrating the thick ice shell with an ice-penetrating probe, and probably diving with an underwater vehicle through dozens of kilometers of water to the ocean floor, to have the chance to find life, if it exists. Technologically, such missions are extremely challenging. The required key technologies include power generation, communications, pressure resistance, radiation hardness, corrosion protection, navigation, miniaturization, autonomy, and sterilization and cleaning. Simpler mission concepts involve impactors and penetrators or – in the case of Enceladus – plume-fly-through missions. Y1 - 2020 U6 - http://dx.doi.org/10.1007/s11214-020-00707-5 SN - 1572-9672 N1 - Corresponding author: Bernd Dachwald VL - 216 IS - Art. 83 PB - Springer CY - Dordrecht ER - TY - BOOK A1 - Wahle, Michael T1 - Kinematik. - (Dynamik ; 1) Y1 - 1993 SN - 3-930085-25-9 PB - Mainz CY - Aachen ET - 1. Aufl. ER - TY - BOOK A1 - Wahle, Michael T1 - Kinetik. - (Dynamik ; 2) Y1 - 1994 SN - 3- 930085-94-1 PB - Mainz CY - Aachen ET - 1. Aufl. ER - TY - PAT A1 - Bagheri, Mohsen A1 - Dahmann, Peter T1 - Kletterroboter mit Gurtantrieb international [Offenlegungsschrift] T1 - Climbing robot for masts [Europäische Patentanmeldung / Internationale Patentanmeldung / US Patentanmeldung] Y1 - 2012 SP - 1 EP - 20 PB - Deutsches Patentamt / Europäisches Patentamt / WIPO / USPTO CY - München / Den Hague / Genf / Alexandria, Virginia ER - TY - GEN A1 - Polaczek, Christa T1 - Kofaser - Kategorien und differentielle Algebren Y1 - 1983 N1 - Bonn, Univ., Diplomarb., 1983 PB - Math. Inst. der Univ. CY - Bonn ER - TY - CHAP A1 - Bosse, Elke A1 - Barnat, Miriam ED - Jenert, Tobias ED - Reinmann, Gabi ED - Schmohl, Tobias T1 - Kombination quantitativer und qualitativer Methoden zur Untersuchung der Studieneingangsphase T2 - Hochschulbildungsforschung. Theoretische, methodologische und methodische Denkanstöße für die Hochschuldidaktik Y1 - 2019 SN - 978-3-658-20308-5 SP - 169 EP - 184 PB - Springer VS CY - Wiesbaden ER - TY - JOUR A1 - Billerbeck, Katrin A1 - Barnat, Miriam A1 - Knutzen, Sönke T1 - Kompetenzorientierung auf dem Prüfstand. Erprobung von Indikatoren für den Kulturwandel JF - Die Hochschullehre N2 - Der Beitrag fokussiert die Frage nach dem Stand des durch die Bologna-Reform angestoßenen Kulturwandels im Hinblick auf Kompetenzorientierung am Beispiel der Technischen Universität Hamburg (TUHH). An der TUHH wird bereits seit einigen Jahren daran gearbeitet, die Lehre grundlegend neu auszurichten. Hierfür setzt das hochschuldidaktische "Zentrum für Lehre und Lernen" (ZLL) verschiedene Maßnahmen ein, wie z.B. eine finanzielle und didaktische Unterstützung von Lehrenden bei der Umstellung ihrer Veranstaltungen, Weiterqualifizierungsangebote und Informationsmaterial. Die Maßnahmen ebenso wie die innovierten Veranstaltungen werden von Lehrenden und Studierenden gut evaluiert. Nach dem Ansatz des Constructive Alignments lässt sich jedoch davon ausgehen, dass der Bereich der Prüfungen für eine Einschätzung des Status Quo der Kompetenzorientierung besonders relevant ist. Dieser wird deshalb anhand der beiden Kriterien Prüfungsformate und Schwierigkeitsstufen von Prüfungsaufgaben näher beleuchtet, die eng mit der Kompetenzorientierung zusammen hängen. Ergebnisse hierzu aus einer universitätsweiten Datenbank zur Studienorganisation sowie aus einer Online-Umfrage unter Studierenden weisen darauf hin, dass das Prüfungsformat "Klausur" nach wie vor am stärksten verbreitet ist; zugleich sind die Studierenden nach einer Selbsteinschätzung in Prüfungen vorrangig mit Aufgaben auf den Taxonomieniveaus "Wiedergeben" und "Anwenden" konfrontiert. Dies lässt sich als Hinweis darauf interpretieren, dass es im Hinblick auf eine Kompetenzorientierung in den Prüfungen noch weiteren Veränderungsbedarf gibt. Y1 - 2016 U6 - http://dx.doi.org/10.3278/HSL1616W SN - 2199-8825 VL - 2016 IS - 16 PB - WBV Media CY - Bielefeld ER - TY - CHAP A1 - Brandt, D. A1 - Güsken, J. A1 - Büchen, W. A1 - [u.a.], A1 - Wahle, Michael T1 - Konstruieren mit Aluminium [Kapitel 4] T2 - Aluminium-Taschenbuch / Hrsg.: Aluminium-Zentrale Düsseldorf. - Bd. 3: Weiterverarbeitung und Anwendung Y1 - 1997 SN - 3-87017-243-6 SP - 359 EP - 544 PB - Aluminium-Verlag CY - Düsseldorf ET - 15. Auflage ER - TY - CHAP A1 - Gitter, R. A1 - Hornhardt, Ch. A1 - Koewius, A. A1 - [u.a.], A1 - Wahle, Michael T1 - Konstruieren mit Aluminium [Kapitel 4] T2 - Aluminium-Taschenbuch / Hrsg.: Aluminium-Zentrale Düsseldorf. - Bd. 3: Weiterverarbeitung und Anwendung Y1 - 2003 SN - 3-87017-275-4 SP - 355 EP - 599 PB - Aluminium-Verlag CY - Düsseldorf ET - 16. Auflage ER - TY - BOOK A1 - Röth, Thilo T1 - Konstruktive und versuchstechnische Entwicklungswerkzeuge zur Gestaltung "fußgängerfreundlicher" Pkw-Vorderwagen : Elektronische Ressource / vorgelegt von Thilo Röth Y1 - 2001 N1 - Dissertation Universität Essen CY - Essen ER - TY - JOUR A1 - Blome, Hans-Joachim A1 - Hoell, Josef A1 - Priester, Wolfgang T1 - Kosmologie JF - Sterne und Weltraum : [enthält 45 Tab.] / Hrsg.: Wilhelm Raith. Autoren: Hans Joachim Blome ... 2., stark erw. und aktualisierte Aufl. Y1 - 2002 SN - 3-11-016866-9 N1 - Lehrbuch der Experimentalphysik ; 8 SP - 439 EP - 582 PB - de Gruyter CY - Berlin [u.a.] ER - TY - BOOK A1 - Blome, Hans-Joachim T1 - Kosmologie und Ethik : Die Stellung des Menschen im Kosmos. Vortrag ... Jahresversammlung Berlin, 26. Mai 2000 Y1 - 2000 PB - Wissen und Verantwortung. Verein zur Carl Friedrich von Weizsäcker- Stiftung e.V. CY - Bünde ER - TY - JOUR A1 - Blome, Hans-Joachim T1 - Kosmologie: Geschichte des Kosmos und Extrapolationen in die Zukunft JF - Der Mensch im Kosmos. 3. ; Berichtsband eines Workshops vom 19. bis 21. April 2001, Kurverwaltung, Medienzentrum Bad Oeynhausen : Der Mensch im Kosmos / Peter R. Sahm ; Gerhard P. J. Thiele (Hrsg.) Y1 - 2002 SN - 3-8265-9737-0 PB - Shaker CY - Aachen ER - TY - JOUR A1 - Bullerschen, Klaus-Gerd A1 - Wilhelmi, Herbert T1 - Kühlung von Lichtbogenofenelektroden durch Wärmerohre JF - Stahl und Eisen. 110 (1990), H. 8 Y1 - 1990 SN - 0378-7559 SP - 91 EP - 98 ER - TY - BOOK A1 - Gerhardt, Hans Joachim T1 - Lagersicherheit lose verlegter Wärmedämmplatten auf Flachdächern gegen Abheben durch Windeinwirkung : Abschlußbericht zum Forschungsvorhaben "Lose verlegte Wärmedämmplatten" / H. J. Gerhardt ; K. K. Bofah ; C. Kramer Y1 - 1989 N1 - Bauforschungsberichte des Bundesministers für Raumordnung, Bauwesen und Städtebau : Bau- und Wohnforschung PB - IRB-Verl. CY - Stuttgart ER - TY - PAT A1 - Rainer, Nähle A1 - Röstel, Reinhard A1 - Wahle, Michael T1 - Lagerungssystem in einem Raumfahrzeug : Patentschrift T1 - Storage system for use inside a spacecraft has damping elements consisting of at least one permanent magnet and vortex flow plate : patent of invention Y1 - 2006 PB - Deutsches Patent- und Markenamt CY - München ER - TY - JOUR A1 - Gerhardt, Hans Joachim A1 - Bofah, K.-K. A1 - Kramer, C. T1 - Lagesicherheit lose verlegter Wärmedämmplatten auf Flachdächern JF - Die Bautechnik. 67 (1990), H. 2 Y1 - 1990 SN - 0005-6820 SP - 55 EP - 60 ER - TY - JOUR A1 - Gerhardt, Hans Joachim A1 - Jung, O. T1 - Lagesicherheit mechanisch befestigter Dachabdichtungen bei Windbelastung JF - Die Bautechnik. 68 (1991), H. 11 Y1 - 1991 SN - 0005-6820 SP - 372 EP - 377 ER -