TY - JOUR A1 - Heinze, D. A1 - Mang, Thomas A1 - Popescu, C. A1 - Weichold, O. T1 - Effect of side chain length and degree of polymerization on the decomposition and crystallization behaviour of chlorinated poly(vinyl ester) oligomers JF - Thermochimica Acta N2 - Four members of a homologous series of chlorinated poly(vinyl ester) oligomers CCl₃–(CH₂CH (OCO(CH₂)ₘCH₃))ₙ–Cl with degrees of polymerization of 10 and 20 were prepared by telomerisation using carbon tetrachloride. The number of side chain carbon atoms ranges from 2 (poly(vinyl acetate) to 18 (poly(vinyl stearate)). The effect of the n-alkyl side chain length and of the degree of polymerization on the thermal stability and crystallization behaviour of the synthesized compounds was investigated. All oligomers degrade in two major steps by first losing HCl and side chains with subsequent breakdown of the backbone. The members with short side chains, up to poly(vinyl octanoate), are amorphous and show internal plasticization, whereas those with high number of side chain carbon atoms are semi-crystalline due to side-chain crystallization. A better packing for poly(vinyl stearate) is also noticeable. The glass transition and melting temperatures as well as the onset temperature of decomposition are influenced to a larger extent by the side chain length than by the degree of polymerization. Thermal stability is improved if both the size and number of side chains increase, but only a long side chain causes a significant increase of the resistance to degradation. This results in a stabilization of PVAc so that oligomers from poly(vinyl octanoate) on are stable under atmospheric conditions. Thus, the way to design stable, chlorinated PVEs oligomers is to use a long n-alkyl side chain. Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.tca.2016.05.015 SN - 0040-6031 (electronic) VL - 637 SP - 143 EP - 153 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Duong, Minh Tuan A1 - Jung, Alexander A1 - Frotscher, Ralf A1 - Staat, Manfred ED - Papadrakakis, M. T1 - A 3D electromechanical FEM-based model for cardiac tissue T2 - ECCOMAS Congress 2016, VII European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island, Greece, 5–10 June 2016 Y1 - 2016 N1 - revised after the conference P11367 ER - TY - CHAP A1 - Tran, Ngoc Trinh A1 - Tran, Thanh Ngoc A1 - Matthies, H. G. A1 - Stavroulakis, G. E. A1 - Staat, Manfred ED - Papadrakakis, M. T1 - Shakedown analysis of plate bending analysis under stochastic uncertainty by chance constrained programming T2 - ECCOMAS Congress 2016, VII European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island, Greece, 5–10 June 2016 Y1 - 2016 ER - TY - JOUR A1 - Kotliar, Konstantin A1 - Lanzl, I. M. T1 - Mit Statistik gemeistert: perfekte Augentropfen und idealer Screeningtest : Möglichkeiten und Grenzen statistischer Methoden beim Glaukom JF - Der Ophthalmologe: Zeitschrift Der Deutschen Ophthalmologischen Gesellschaft N2 - Hintergrund Die Anwendung und das Verständnis von Statistik sind sehr wichtig für die biomedizinische Forschung und für die klinische Praxis. Dies gilt insbesondere auch zur Abschätzung der Möglichkeiten unterschiedlichster Diagnostik- und Therapieoptionen beim Glaukom. Die scheinbare Komplexität der Statistik, die zum Teil dem „gesunden Menschenverstand“ zu widersprechen scheint, zusammen mit der nur vorsichtigen Akzeptanz der Statistik bei vielen Medizinern können zu bewussten und unbewussten Manipulationen bei der Datendarstellung und -interpretation führen. Ziel der Arbeit Ziel ist die verständliche Darstellung einiger typischer Fehler in der medizinisch-statistischen Datenbehandlung. Material und Methoden Anhand hypothetischer Beispiele aus der Glaukomdiagnostik erfolgen die Darstellung der Wirkung eines hypotensiven Medikamentes sowie die Beurteilung der Ergebnisse eines diagnostischen Tests. Es werden die typischsten statistischen Einsatzbereiche und Irrtumsquellen ausführlich und verständlich analysiert Ergebnisse Mechanismen von Datenmanipulation und falscher Dateninterpretation werden aufgeklärt. Typische Irrtumsquellen bei der statistischen Auswertung und Datendarstellung werden dabei erläutert. Schlussfolgerungen Die erläuterten praktischen Beispiele zeigen die Notwendigkeit, die Grundlagen der Statistik zu verstehen und korrekt anwenden zu können. Fehlendes Grundlagenwissen und Halbwissen der medizinischen Statistik können zu folgenschweren Missverständnissen und falschen Entscheidungen in der medizinischen Forschung, aber auch in der klinischen Praxis führen. Y1 - 2016 U6 - http://dx.doi.org/10.1007/s00347-016-0312-y SN - 0941-293X SN - 1433-0423 N1 - Englischer Titel: Mastered with statistics: perfect eye drops and ideal screening test : possibilities and limits of statistical methods for glaucoma IS - 113 SP - 838 EP - 843 PB - Springer CY - Berlin ER - TY - CHAP A1 - König, Johannes Alexander A1 - Wolf, Martin ED - Stephanidis, C. T1 - The pyramid assessment framework for ‘competence developing games’ T2 - Communications in Computer and Information Science Y1 - 2016 SN - 978-331940541-4 U6 - http://dx.doi.org/10.1007/978-3-319-40542-1_37 SN - 1865-0929 N1 - 18th International Conference on Posters’ Extended Abstracts, HCI International 2016; Toronto; Canada; 17 July 2016 through 22 July 2016 VL - 618 SP - 232 EP - 237 PB - Springer ER - TY - BOOK A1 - Feuerriegel, Uwe T1 - Verfahrenstechnik mit EXCEL: Verfahrenstechnische Berechnungen effektiv durchführen und professionell dokumentieren Y1 - 2016 SN - 978-3-658-02902-9 U6 - http://dx.doi.org/10.1007/978-3-658-02903-6 N1 - 152 Abbildungen, 94 Abbildungen in Farbe Gedruckt in der Bibliothek unter der Signatur: 21 ZNK 11 PB - Springer Fachmedien CY - Wiesbaden ER - TY - JOUR A1 - Lind, Thorsten Patric T1 - Zurechenbarkeit des als Mitglied des Aufsichtsrats einer Aktiengesellschaft erlangten Wissens des Prokuristen einer Bank : BGH, Urteil vom 26.04.2016 - XI ZR 108/15 (OLG München) JF - LMK : kommentierte BGH-Rechtsprechung ; in Zsarb. mit der Neuen Juristischen Wochenschrift / Lindenmaier-Möhring N2 - Mit der vorliegenden, parallel entsprechend in 10 weiteren Verfahren ergangenen Entscheidung behandelte der BGH zum wiederholten Male das Geschäftsmodell der Accessio Wertpapierhandelshaus AG („A AG“, früher: Wertpapierhandelshaus Driver & Bengsch AG). Die klagenden Anleger, zunächst nur akquiriert durch ein Tagesgeldkonto mit besonders attraktiven Zinsen, schlossen im Weiteren mit dieser einen Vermögensverwaltungsvertrag ab. Zur Abwicklung der Wertpapiergeschäfte eröffneten sie über die A AG zugleich ein Depotkonto bei der beklagten Discount-Brokerin. Für dieses erhielt die A AG eine Transaktionsvollmacht. Die Discount-Brokerin schuldete nach den Vertragsdokumenten über die gesetzlichen Aufklärungs- und Erkundigungspflichten bei Auftragsausführung hinaus keine Anlageberatung („execution-only-business“). Durch nach ihrer Behauptung fehlerhafte Anlageberatung der A AG erlitten die Anleger einen Schaden. In dem Rechtsstreit verlangten sie dessen Ersatz von der Discount-Brokerin, da die A AG zwischenzeitlich insolvent wurde. Y1 - 2016 SN - 1611-1095 SP - 380532 PB - Beck CY - München ER - TY - CHAP A1 - Ferrein, Alexander A1 - Maier, Christopher A1 - Mühlbacher, Clemens A1 - Niemüller, Tim A1 - Steinbauer, Gerald A1 - Vassos, Stravros T1 - Controlling logistics robots with the action-based language YAGI T2 - Intelligent Robotics and Applications: 9th International Conference, ICIRA 2016, Tokyo, Japan, August 22-24, 2016, Proceedings, Part I Y1 - 2016 SN - 978-3-319-43505-3 (Print) SN - 978-3-319-43506-0 (Online) U6 - http://dx.doi.org/10.1007/978-3-319-43506-0_46 N1 - Series: Lecture Notes in Computer Science (including subseries Lecture Notes in Artificial Intelligence and Lecture Notes in Bioinformatics) VL - 9834 SP - 525 EP - 537 PB - Springer ER - TY - CHAP A1 - Neumann, Tobias A1 - Dülberg, Enno A1 - Schiffer, Stefan A1 - Ferrein, Alexander T1 - A rotating platform for swift acquisition of dense 3D point clouds T2 - Intelligent Robotics and Applications: 9th International Conference, ICIRA 2016, Tokyo, Japan, August 22-24, 2016, Proceedings, Part I Y1 - 2016 SN - 978-3-319-43505-3 (Print) SN - 978-3-319-43506-0 (Online) U6 - http://dx.doi.org/10.1007/978-3-319-43506-0_22 N1 - Series: Lecture Notes in Computer Science (including subseries Lecture Notes in Artificial Intelligence and Lecture Notes in Bioinformatics) VL - 9834 SP - 257 EP - 268 PB - Springer ER - TY - CHAP A1 - Rupp, Matthias A1 - Kuperjans, Isabel A1 - Schulze, Sven ED - Berns, Karsten T1 - Energetische und ökologische Bewertung hybrider Antriebe im städtischen Busverkehr T2 - Commercial vehicle technology 2016 : proceedings of the 4th Commercial Vehicle Technology Symposium (CVT 2016), March 8-10, 2016, University of Kaiserslautern, Kaiserslautern, Germany N2 - In Anbetracht weltweit zunehmend strengerer klimapolitischer Ziele steigt auch der Druck für Nutzfahrzeughersteller, effizientere und umweltfreundlichere Technologien zu entwickeln. Den Blick bei der Bewertung dieser ausschließlich auf die Fahrzeugnutzung zu richten, ist längst nicht mehr zufriedenstellend. Im Rahmen dieser Analyse wird ein gegenwärtig auf dem Markt erwerblicher und in deutschen Städten bereits seit Jahren betriebener Hybridbus energetisch und ökologisch mit einem konventionell angetriebenen, nahezu baugleichen Modell entlang des Lebensweges bewertet. Nach Definition von Ziel und Untersuchungsrahmen wird ein Überblick auf bereits durchgeführte Lebenszyklusanalysen zu Hybridbussen im Stadtverkehr gegeben und Schlussfolgerungen für die anschließende Analyse abgeleitet. Diese wird im Rahmen einer energetischen und ökologischen Bewertung beider Produktsysteme anhand der Parameter "Primärenergieeinsatz" und "CO2äq Emissionen" praktiziert. Der Fahrzeugrumpf beider Fahrzeuge des gleichen Modells wird dabei als einheitlich angenommen, sodass bei dem Vergleich der Herstellung vereinfacht nur die sich unterscheidenden Komponenten des Antriebstranges berücksichtigt werden. Die Resultate der Wirkungsabschätzung werden als Differenz des Hybridbusses gegenüber dem Referenzfahrzeug über die einzelnen Lebenszyklusphasen dargestellt. Schließlich werden Prognosen getroffen, ab welcher Strecke die bei der Herstellung erzeugten höheren CO2äq Emissionen des Hybridantriebstranges gegenüber dem Referenzmodell ausgeglichen werden. Y1 - 2016 SP - 227 EP - 237 PB - Shaker CY - Aachen ER - TY - CHAP A1 - Bhattarai, Aroj A1 - Frotscher, Ralf A1 - Staat, Manfred ED - Natal Jorge, Renato T1 - Significance of fibre geometry on passive-active response of pelvic muscles to evaluate pelvic dysfunction T2 - BioMedWomen: Proceedings of the international conference on clinical and bioengineering for women's health Y1 - 2016 SN - 978-1-138-02910-1 SP - 185 EP - 188 PB - CRC Press CY - Boca Raton ER - TY - GEN A1 - Alt, Helmut T1 - Energiewende zwischen Wunsch und Wirklichkeit : Von der Grundlastdeckung zur Lückenlastdeckung N2 - Folien des Vortrags. VDI-Bezirksverband Dresden, Arbeitskreis Energietechnik, am Montag, 05.09.2016 Y1 - 2016 ER - TY - JOUR A1 - Kern, Alexander T1 - Blitz- und Überspannungsschutz von Kernkraftwerken - Nachweisführung der ausreichenden Sicherheit für leittechnische Einrichtungen auch bei Blitzeinschlägen mit extremen Parametern JF - Atw. International Journal for Nuclear Power N2 - Für das Auftreten extremer Wetterereignisse werden für Kernkraftwerke Eintrittshäufigkeiten für nicht mehr beherrschbare Zustände von unter 10⁻⁴/a gefordert. Dies gilt auch für die Einwirkung von Blitzeinschlägen. Die bisherige Nachweisführung zu Blitz- und Überspannungsschutz eines KKW in Deutschland ist deterministisch. In diesem Bericht werden das Vorgehen für einen entsprechenden Nachweis für leittechnische Einrichtungen der Sicherheitstechnik von KKW, der zur geforderten Zielgröße der Eintrittshäufigkeit führt. Die Ergebnisse werden zusammenfassend bewertet. Y1 - 2016 SN - 1431-5254 VL - 61 IS - 8/9 SP - 534 EP - 543 PB - Inforum CY - Berlin ER - TY - BOOK A1 - Lauth, Jakob T1 - Physikalische Chemie, 5: Elektrochemie Y1 - 2016 SN - 978-3-662-47559-1 PB - Springer CY - Berlin ER - TY - BOOK A1 - Lauth, Jakob T1 - Physikalische Chemie, 4: Reaktionskinetik Y1 - 2016 SN - 978-3-662-47674-1 PB - Springer CY - Berlin ER - TY - BOOK A1 - Lauth, Jakob T1 - Physikalische Chemie, 3: Phasengleichgewichte Y1 - 2016 SN - 978-3-662-47571-3 PB - Springer CY - Berlin ER - TY - BOOK A1 - Lauth, Jakob T1 - Physikalische Chemie, 2: Chemische Thermodynamik Y1 - 2016 SN - 978-3-662-47621-5 PB - Springer CY - Berlin ER - TY - BOOK A1 - Lauth, Jakob T1 - Physikalische Chemie, 1: Grundlagen der Thermodynamik und Verhalten der Gase Y1 - 2016 SN - 978-3-662-47676-5 PB - Springer CY - Berlin ER - TY - BOOK A1 - Lauth, Jakob A1 - Kowalczyk, Jürgen T1 - Einführung in die Physik und Chemie der Grenzflächen und Kolloide Y1 - 2016 SN - 978-3-662-47018-3 U6 - http://dx.doi.org/10.1007/978-3-662-47018-3 PB - Springer CY - Berlin ER - TY - JOUR A1 - Ferrein, Alexander A1 - Schiffer, Stefan A1 - Booysen, T. A1 - Stopforth, R. T1 - Why it is harder to run RoboCup in South Africa: Experiences from German South African collaborations JF - International Journal of Advanced Robotic Systems N2 - Robots are widely used as a vehicle to spark interest in science and technology in learners. A number of initiatives focus on this issue, for instance, the Roberta Initiative, the FIRST Lego League, the World Robot Olympiad and RoboCup Junior. Robotic competitions are valuable not only for school learners but also for university students, as the RoboCup initiative shows. Besides technical skills, the students get some project exposure and experience what it means to finish their tasks on time. But qualifying students for future high-tech areas should not only be for students from developed countries. In this article, we present our experiences with research and education in robotics within the RoboCup initiative, in Germany and South Africa; we report on our experiences with trying to get the RoboCup initiative in South Africa going. RoboCup has a huge support base of academic institutions in Germany; this is not the case in South Africa. We present our ‘north–south’ collaboration initiatives in RoboCup between Germany and South Africa and discuss some of the reasons why we think it is harder to run RoboCup in South Africa. Y1 - 2016 U6 - http://dx.doi.org/10.1177/1729881416662789 SN - 1729-8806 VL - 13 IS - 5 SP - 1 EP - 13 ER - TY - CHAP A1 - Kessler, Julia A1 - Balc, Nicolae A1 - Gebhardt, Andreas T1 - Basic research on lattice structures focused on the strut shape and welding beads T2 - Physics Procedia Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.phpro.2016.08.086 SN - 1875-3884 N1 - Laser Assisted Net Shape Engineering 9th International Conference on Photonic Technologies Proceedings of the LANE 2016 VL - Vol. 83 SP - 833 EP - 838 ER - TY - CHAP A1 - Bagheri, Mohsen A1 - Schleupen, Josef A1 - Dahmann, Peter A1 - Kallweit, Stephan T1 - Kletternde Wartungsplattform für die wetterunabhängige Instandhaltung von Rotorblättern an Windenergieanlagen - SMART T2 - AKIDA 2016 Aachener Kolloquium für Instandhaltung, Diagnose und Anlagenüberwachung (AKIDA) am 15. und 16.11.2016, Technologiezentrum Aachen N2 - In Deutschland liegt der Anteil der Windkraft an der Gesamtstromerzeugung bei 13,3% mit mehr als 25.000 installierten Windenergieanlagen (WEA). Weltweit erfährt die Windbranche ein rasantes Wachstum. Indien und China berichten eine jährliche Wachstumsrate an Neuinstallationen von 45%. Die Technologie zur Erzeugung elektrischer Energie aus Windkraft ist noch vergleichsweise jung. Durch die weltweit steigende Anzahl an Windenergieanlagen wächst zunehmend der Bedarf an innovativen Wartungslösungen. Komponenten wie Generator oder Getriebe sind inzwischen weitestgehend ausgereift. Der Fokus richtet sich zunehmend auf die wesentliche Kernkomponente - die Rotorblätter. Industriekletterer inspizieren die Rotorblätter oder Türme i.d.R. in einem zwei Jahres Rhythmus. Sie werden zunehmend durch Seilarbeitsbühnen unterstützt. Für größere Reparaturen kommen Kräne zum Einsatz, mit denen das Rotorblatt für die Instandhaltung demontiert wird. Die Standardinspektion besteht aus Sicht- und Klopfprüfung der Rotorblattoberfläche und ist nur bei sehr ruhiger Wetterlage durchführbar. Seit September 2014 wird das Forschungsprojekt SMART (Scanning, Monitoring, Analysis, Repair and Transportation), Entwicklung einer Wartungsplattform für WEA, vom BMWi gefördert. Das Konsortium besteht aus zwei Firmen und der Fachhochschule Aachen. Die SMART-Anlage klettert reibschlüssig am Turm der WEA mittels speziellen Kettenfahrwerken (Abbildung) auf- und abwärts. Ein ringförmiges Spannsystems, basierend auf dem Konzept der „Nürnberger“-Schere, erzeugt die erforderliche Anpresskraft für den Kletterprozess. Wettergeschützte Arbeitskabinen ermöglichen die ganzjährige Instandhaltung von Rotorblättern und ebenso Türmen. Dadurch können Wartungsarbeiten auf 24 Stunden am Tag ausgeweitet werden. Der kombinierte Einsatz (Sensorfusion) bildgebender Messtechnik wie Thermografie, Ultraschall, und Terahertz in der Arbeitskabine kann die Dokumentation, Effizienz und Qualität der Instandhaltungsarbeiten erheblich verbessern. Langfristiges Ziel von SMART ist ein Condition Monitoring für Rotorblätter und Türme auf Basis digitalisierter dreidimensionaler Volumenscans. Der kooperative Einsatz mit UAVs erweitert die Instandhaltungsstrategie. UAVs ermöglichen die schnelle, kostengünstige globale optische Inspektion von Rotorblattoberflächen zur Detektion potentieller Fehlstellen. Der „Proof-of-Concept“ Meilenstein wurde mit der Demonstration eines funktionsfähigen Modells im Dezember 2015 erfolgreich abgeschlossen. Y1 - 2016 ER - TY - JOUR A1 - Wagner, Torsten A1 - Vornholt, Wolfgang A1 - Werner, Frederik A1 - Yoshinobu, Tatsuo A1 - Miyamoto, Ko-Ichiro A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Light-addressable potentiometric sensor (LAPS) combined with magnetic beads for pharmaceutical screening JF - Physics in medicine N2 - The light-addressable potentiometric sensor (LAPS) has the unique feature to address different regions of a sensor surface without the need of complex structures. Measurements at different locations on the sensor surface can be performed in a common analyte solution, which distinctly simplifies the fluidic set-up. However, the measurement in a single analyte chamber prevents the application of different drugs or different concentrations of a drug to each measurement spot at the same time as in the case of multi-reservoir-based set-ups. In this work, the authors designed a LAPS-based set-up for cell culture screening that utilises magnetic beads loaded with the endotoxin (lipopolysaccharides, LPS), to generate a spatially distributed gradient of analyte concentration. Different external magnetic fields can be adjusted to move the magnetic beads loaded with a specific drug within the measurement cell. By recording the metabolic activities of a cell layer cultured on top of the LAPS surface, this work shows the possibility to apply different concentrations of a sample along the LAPS measurement spots within a common analyte solution. Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.phmed.2016.03.001 SN - 2352-4510 VL - 2016 IS - 1 SP - 2 EP - 7 ER - TY - JOUR A1 - Doll, Theodor A1 - Wagner, Torsten A1 - Wagner, Patrick A1 - Schöning, Michael Josef T1 - Engineering of functional interfaces / Theodor Doll ; Torsten Wagner ; Patrick Wagner ; Michael J. Schöning (eds.) JF - Physica status solidi (a) Y1 - 2016 U6 - http://dx.doi.org/10.1002/pssa.201670641 SN - 1862-6319 VL - 213 IS - 6 SP - 1393 EP - 1394 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Knobe, M. A1 - Giesen, M. A1 - Plate, S. A1 - Gradl-Dietsch, G. A1 - Buecking, B. A1 - Eschbach, D. A1 - Laack, Walter van A1 - Pape, H.-C. T1 - The Aachen mobility and balance index to measure physiological falls risk: a comparison with the Tinetti POMA scale JF - European Journal Of Trauma And Emergency Surgery N2 - Purpose The most commonly used mobility assessments for screening risk of falls among older adults are rating scales such as the Tinetti performance oriented mobility assessment (POMA). However, its correlation with falls is not always predictable and disadvantages of the scale include difficulty to assess many of the items on a 3-point scale and poor specificity. The purpose of this study was to describe the ability of the new Aachen Mobility and Balance Index (AMBI) to discriminate between subjects with a fall history and subjects without such events in comparison to the Tinetti POMA Scale. Methods For this prospective cohort study, 24 participants in the study group and 10 in the control group were selected from a population of patients in our hospital who had met the stringent inclusion criteria. Both groups completed the Tinetti POMA Scale (gait and balance component) and the AMBI (tandem stance, tandem walk, ten-meter-walk-test, sit-to-stand with five repetitions, 360° turns, timed-up-and-go-test and measurement of the dominant hand grip strength). A history of falls and hospitalization in the past year were evaluated retrospectively. The relationships among the mobility tests were examined with Bland–Altmananalysis. Receiver-operated characteristics curves, sensitivity and specificity were calculated. Results The study showed a strong negative correlation between the AMBI (17 points max., highest fall risk) and Tinetti POMA Scale (28 points max., lowest fall risk; r = −0.78, p < 0.001) with an excellent discrimination between community-dwelling older people and a younger control group. However, there were no differences in any of the mobility and balance measurements between participants with and without a fall history with equal characteristics in test comparison (AMBI vs. Tinetti POMA Scale: AUC 0.570 vs. 0.598; p = 0.762). The Tinetti POMA Scale (cut-off <20 points) showed a sensitivity of 0.45 and a specificity of 0.69, the AMBI a sensitivity of 0.64 and a specificity of 0.46 (cut-off >5 points). Conclusion The AMBI comprises mobility and balance tasks with increasing difficulty as well as a measurement of the dominant hand-grip strength. Its ability to identify fallers was comparable to the Tinetti POMA Scale. However, both measurement sets showed shortcomings in discrimination between fallers and non-fallers based on a self-reported retrospective falls-status. KW - Tinetti test KW - Mobility KW - Mobility tests KW - Ground-level falls KW - Elderly KW - Fall prevention KW - Co-managed care KW - Balance Y1 - 2016 U6 - http://dx.doi.org/10.1007/s00068-016-0693-2 SN - 1863-9941 VL - 42 IS - 5 SP - 537 EP - 545 PB - Springer CY - Berlin ER - TY - JOUR A1 - Molinnus, Denise A1 - Sorich, Maren A1 - Bartz, Alexander A1 - Siegert, Petra A1 - Willenberg, Holger S. A1 - Lisdat, Fred A1 - Poghossian, Arshak A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Towards an adrenaline biosensor based on substrate recycling amplification in combination with an enzyme logic gate JF - Sensors and Actuators B: Chemical N2 - An amperometric biosensor using a substrate recycling principle was realized for the detection of low adrenaline concentrations (1 nM) by measurements in phosphate buffer and Ringer’s solution at pH 6.5 and pH 7.4, respectively. In proof-of-concept experiments, a Boolean logic-gate principle has been applied to develop a digital adrenaline biosensor based on an enzyme AND logic gate. The obtained results demonstrate that the developed digital biosensor is capable for a rapid qualitative determination of the presence/absence of adrenaline in a YES/NO statement. Such digital biosensor could be used in clinical diagnostics for the control of a correct insertion of a catheter in the adrenal veins during adrenal venous-sampling procedure. Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.snb.2016.06.064 SN - 0925-4005 VL - 237 SP - 190 EP - 195 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Funke, Harald A1 - Keinz, Jan A1 - Börner, S. A1 - Hendrick, P. A1 - Elsing, R. T1 - Testing and analysis of the impact on engine cycle parameters and control system modifications using hydrogen or methane as fuel in an industrial gas turbine T2 - Progress in propulsion physics ; Volume 8 Y1 - 2016 SN - 978-5-94588-191-4 U6 - http://dx.doi.org/10.1051/eucass/201608409 SP - 409 EP - 426 PB - EDP Sciences CY - o.O. ER - TY - CHAP A1 - Harzheim, Thomas A1 - Heuermann, Holger A1 - Marso, Michel T1 - An Adaptive Biasing Method for SRD Comb Generators T2 - 2016 German Microwave Conference (GeMiC) Y1 - 2016 U6 - http://dx.doi.org/10.1109/GEMIC.2016.7461613 N1 - GeMiC 2016 ; March 14–16, 2016, Bochum, Germany SP - 289 EP - 292 PB - IEEE ER - TY - JOUR A1 - Valero, Daniel A1 - Bung, Daniel B. T1 - Development of the interfacial air layer in the non-aerated region of high-velocity spillway flows: Instabilities growth, entrapped air and influence on the self-aeration onset JF - International Journal of Multiphase Flow N2 - Self-aeration is traditionally explained by the water turbulent boundary layer outer edge intersection with the free surface. This paper presents a discussion on the commonly accepted hypothesis behind the computation of the critical point of self-aeration in spillway flows and a new formulation is proposed based on the existence of a developing air flow over the free surface. Upstream of the inception point of self-aeration, some surface roughening has been often reported in previous studies which consequently implies some entrapped air transport and air–water flows coupling. Such air flow is proven in this study by presenting measured air velocities and computing the air boundary layer thickness for a 1V:2H smooth chute flow. Additionally, the growth rate of free surface waves has been analysed by means of Ultrasonic Sensors measurements, obtaining also the entrapped air concentration. High-speed camera imaging has been used for qualitative study of the flow perturbations. Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.ijmultiphaseflow.2016.04.012 SN - 0301-9322 VL - 84 SP - 66 EP - 74 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Ghosch, S. A1 - Baier, M. A1 - Schütz, J. A1 - Schneider, Felix A1 - Scherer, Ulrich W. T1 - Analysis of electronic autoradiographs by mathematical post-processing JF - Radiation Effects and Defects in Solids: Incorporating plasma science and plasma technology N2 - Autoradiography is a well-established method of nuclear imaging. When different radionuclides are present simultaneously, additional processing is needed to distinguish distributions of radionuclides. In this work, a method is presented where aluminium absorbers of different thickness are used to produce images with different cut-off energies. By subtracting images pixel-by-pixel one can generate images representing certain ranges of β-particle energies. The method is applied to the measurement of irradiated reactor graphite samples containing several radionuclides to determine the spatial distribution of these radionuclides within pre-defined energy windows. The process was repeated under fixed parameters after thermal treatment of the samples. The greyscale images of the distribution after treatment were subtracted from the corresponding pre-treatment images. Significant changes in the intensity and distribution of radionuclides could be observed in some samples. Due to the thermal treatment parameters the most significant differences were observed in the ³H and ¹⁴C inventory and distribution. Y1 - 2016 U6 - http://dx.doi.org/10.1080/10420150.2016.1155587 SN - 1029-4953 VL - 171 IS - 1-2 SP - 161 EP - 172 PB - Taylor & Francis CY - London ER - TY - CHAP A1 - Broenner, Simon A1 - Höfken, Hans-Wilhelm A1 - Schuba, Marko T1 - Streamlining extraction and analysis of android RAM images T2 - Proceedings of the 2nd international conference on information systems security and privacy Y1 - 2016 SN - 978-989-758-167-0 U6 - http://dx.doi.org/10.5220/0005652802550264 SP - 255 EP - 264 ER - TY - JOUR A1 - Belavy, Daniel L. A1 - Albracht, Kirsten A1 - Bruggemann, Gert-Peter A1 - Vergroesen, Pieter-Paul A. A1 - Dieen, Jaap H. van T1 - Can exercise positively influence the intervertebral disc? JF - Sports Medicine N2 - To better understand what kinds of sports and exercise could be beneficial for the intervertebral disc (IVD), we performed a review to synthesise the literature on IVD adaptation with loading and exercise. The state of the literature did not permit a systematic review; therefore, we performed a narrative review. The majority of the available data come from cell or whole-disc loading models and animal exercise models. However, some studies have examined the impact of specific sports on IVD degeneration in humans and acute exercise on disc size. Based on the data available in the literature, loading types that are likely beneficial to the IVD are dynamic, axial, at slow to moderate movement speeds, and of a magnitude experienced in walking and jogging. Static loading, torsional loading, flexion with compression, rapid loading, high-impact loading and explosive tasks are likely detrimental for the IVD. Reduced physical activity and disuse appear to be detrimental for the IVD. We also consider the impact of genetics and the likelihood of a ‘critical period’ for the effect of exercise in IVD development. The current review summarises the literature to increase awareness amongst exercise, rehabilitation and ergonomic professionals regarding IVD health and provides recommendations on future directions in research. KW - Intradiscal Pressure KW - Annulus Fibrosus KW - Disc Degeneration KW - Nucleus Pulposus KW - Intervertebral Disc Y1 - 2016 U6 - http://dx.doi.org/10.1007/s40279-015-0444-2 SN - 1179-2035 VL - 46 IS - 4 SP - 473 EP - 485 PB - Springer CY - Berlin ER - TY - CHAP A1 - Krause, Thomas T1 - Bauabrechnung und Mengenermittlung T2 - Zahlentafeln für den Baubetrieb N2 - In diesem Kapitel werden die Abrechnungsvorschriften wichtiger ATV kurz, aber umfassend zusammengestellt. Einigen Abrechnungsbestimmungen für Einzelleistungen, die keine Nebenleistungen sind ((siehe DIN 18299 und Abschnitt 4 der jeweiligen ATV), sind mit aufgenommen worden; die ATV enthalten jedoch weitergehende Festlegungen über Nebenleistungen und Besondere Leistungen. Im Anschluss folgen Hinweise zu den Toleranzen im Hochbau sowie im Straßenbau. Y1 - 2016 SN - 978-3-658-02838-1 (Online) SN - 978-3-658-02837-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-658-02838-1_7 SP - 963 EP - 1027 PB - Springer Vieweg CY - Wiesbaden ET - 9., überarb. und aktual. Aufl. ER - TY - CHAP A1 - Schlösser, Karl Helmut T1 - Arbeitsvorbereitung und Ablaufplanung T2 - Zahlentafeln für den Baubetrieb N2 - Kosten- und Verfahrensvergleiche können dabei zur Ermittlung des für die Aufgabe geeignetsten Bauverfahren führen. Für die sich daran anschließende Ablaufplanung werden die verschiedenen graphischen sowie rechnerischen Instrumente (Terminliste und Taktplan, Balkenplan, Weg-Zeit-Diagramm und Netzplan) erläutert und anhand von Beispielen vertieft. Schließlich wird ein im Rahmen der Arbeits- und Nachkalkulation vorzunehmender Soll-Ist-Vergleich mit Hilfe des Bauarbeitsschlüssels (BAS) zur Überprüfung der Aufwands- und Leistungswerte dargestellt. Y1 - 2016 SN - 978-3-658-02838-1 (Online) SN - 978-3-658-02837-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-658-02838-1_8 SP - 1029 EP - 1067 PB - Springer Vieweg CY - Wiesbaden ET - 9., überarb. und aktual. Aufl. ER - TY - CHAP A1 - Krause, Thomas A1 - Oettel, Britta T1 - Baumaschinen T2 - Zahlentafeln für den Baubetrieb N2 - Die Leistungsermittlung und Bemessung von Baumaschinen für die folgenden Bereiche werden bearbeitet: Maschinen für den Betonbau, Hebezeuge, Maschinen für den Erdbau, Straßenbaumaschinen, Rückbaugeräte und Elemente der Baustelleneinrichtung Y1 - 2016 SN - 978-3-658-02838-1 (Online) SN - 978-3-658-02837-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-658-02838-1_9 SP - 1069 EP - 1163 PB - Springer Vieweg CY - Wiesbaden ET - 9., überarb. und aktual. Aufl. ER - TY - CHAP A1 - Ulke, Bernd T1 - Boden, Baugrube, Verbau T2 - Zahlentafeln für den Baubetrieb N2 - Die Lösung den Baugrund betreffender Fragestellungen beginnen i. d. R. mit der Durchführung von Baugrunderkundungen, um alle notwendigen Parameter zu erhalten, die für die Planung und Durchführung von Bauvorhaben notwendig sind. Im Folgenden werden die wichtigsten Erkundungen in Abhängigkeit der erforderlichen Güteklasse der Proben beschrieben und vorgestellt. Y1 - 2016 SN - 978-3-658-02838-1 (Online) SN - 978-3-658-02837-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-658-02838-1_10 SP - 1165 EP - 1246 PB - Springer Vieweg CY - Wiesbaden ET - 9., überarb. und aktual. Aufl. ER - TY - CHAP A1 - Krause, Thomas A1 - Kremer, Norbert T1 - Schalung und Gerüste T2 - Zahlentafeln für den Baubetrieb N2 - Systemschalungen und Systemgerüste haben den Baustellenbetrieb in vielen Bereichen sehr vereinfacht. Dennoch sind Kenntnisse in diesen Feldern für eine erfolgreiche und effektive Bauleitung unverzichtbar. In diesem Kapitel werden Hinweise und Empfehlungen für die Bemessung und Einsatz von Schalungen, Trag- und Arbeitsgerüsten für den Baustellenbetrieb gegeben. Y1 - 2016 SN - 978-3-658-02838-1 (Online) SN - 978-3-658-02837-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-658-02838-1_11 SP - 1247 EP - 1296 PB - Springer Vieweg CY - Wiesbaden ET - 9., überarb. und aktual. Aufl. ER - TY - CHAP A1 - Martin, Joachim T1 - Betriebsorganisation T2 - Zahlentafeln für den Baubetrieb N2 - Das Kapitel behandelt, ausgehend von Begriffen und Aufgaben der Betriebsorganisation, die Aufbau- und Ablauforganisation der Bauunternehmung sowie die Gestaltung einer Projekt-organisation. Es folgt eine Darstellung der Managementsysteme für Qualität, Umwelt und Arbeitsschutz, die sich zunehmend als sog. integrierte Managementsysteme (IMS) auch in Bauunternehmen etablieren. Grundlagen des Personalmanagements und des betrieblichen Rechnungswesens, die für eine(n) Baubetriebler(in) relevant sein können, ergänzen das Kap. Betriebsorganisation. Den Abschluss bilden Hinweise zum Berichtswesen der Baustelle. Y1 - 2016 SN - 978-3-658-02838-1 (Online) SN - 978-3-658-02837-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-658-02838-1_12 SP - 1297 EP - 1389 PB - Springer Vieweg CY - Wiesbaden ET - 9., überarb. und aktual. Aufl. ER - TY - CHAP A1 - Streit, Wilfried T1 - Kalkulation T2 - Zahlentafeln für den Baubetrieb N2 - Das Kapitel behandelt die Kosten- und Preisermittlung, die Kostenvorgabe und Kostenkontrolle. Der Angebotspreis wird aufgeschlüsselt in die Einzelkosten der Teilleistungen, die Baustellengemeinkosten, die Allgemeinen Geschäftskosten und einen Zuschlag für Wagnis und Gewinn. Auf der Basis der Angebotskalkulation werden die Vorgaben für die Kostenkontrolle entwickelt. Y1 - 2016 SN - 978-3-658-02838-1 (Online) SN - 978-3-658-02837-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-658-02838-1_13 SP - 1391 EP - 1501 PB - Springer Vieweg CY - Wiesbaden ET - 9., überarb. und aktual. Aufl. ER - TY - CHAP A1 - Lemke, Jörg T1 - Unfallverhütung, Arbeits- und Gesundheitsschutz T2 - Zahlentafeln für den Baubetrieb N2 - Neben dem durch Unfälle und Krankheiten entstehenden menschlichen Leids und der daraus resultierenden moralischen Verpflichtung, sich und seine Mitmenschen vor Schaden zu bewahren, ist der Arbeits- und Gesundheitsschutz auch ein Gebot wirtschaftlichen Handelns, da Arbeitsunfälle und Berufskrankheiten Ausfallzeiten und Kosten verursachen. So gehören Arbeits- und Gesundheitsschutz zu den wichtigen Aufgaben eines Unternehmens. Y1 - 2016 SN - 978-3-658-02838-1 (Online) SN - 978-3-658-02837-4 (Print) U6 - http://dx.doi.org/10.1007/978-3-658-02838-1_15 SP - 1599 EP - 1638 PB - Springer Vieweg CY - Wiesbaden ET - 9., überarb. und aktual. Aufl. ER - TY - CHAP A1 - Borchert, Jörg A1 - Rothe, Sebastian ED - Suntrop, Carsten T1 - Energiemanagement und Versorgung von Chemieparks – Ein Ansatz zur wertschöpfungsgetriebenen Risikosteuerung T2 - Chemiestandorte : Markt, Herausforderungen und Geschäftsmodelle Y1 - 2016 SN - 978-3-527-33441-4 SP - 193 EP - 210 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Miyamoto, Ko-Ichiro A1 - Sato, Takuya A1 - Abe, Minami A1 - Wagner, Torsten A1 - Schöning, Michael Josef A1 - Yoshinobu, Tatsuo T1 - Light-addressable potentiometric sensor as a sensing element in plug-based microfluidic devices JF - Micromachines N2 - A plug-based microfluidic system based on the principle of the light-addressable potentiometric sensor (LAPS) is proposed. The LAPS is a semiconductor-based chemical sensor, which has a free addressability of the measurement point on the sensing surface. By combining a microfluidic device and LAPS, ion sensing can be performed anywhere inside the microfluidic channel. In this study, the sample solution to be measured was introduced into the channel in a form of a plug with a volume in the range of microliters. Taking advantage of the light-addressability, the position of the plug could be monitored and pneumatically controlled. With the developed system, the pH value of a plug with a volume down to 400 nL could be measured. As an example of plug-based operation, two plugs were merged in the channel, and the pH change was detected by differential measurement. KW - light-addressable potentiometric sensor KW - plug-based microfluidic device KW - chemical sensor Y1 - 2016 U6 - http://dx.doi.org/10.3390/mi7070111 SN - 2072-666X N1 - This article belongs to the Special Issue "Micro/Nano Devices for Chemical Analysis" VL - 7 IS - 7 SP - 111 PB - MDPI CY - Basel ER - TY - CHAP A1 - Kolditz, Melanie A1 - Albin, Thivaharan A1 - Albracht, Kirsten A1 - Brüggemann, Gert-Peter A1 - Abel, Dirk T1 - Isokinematic leg extension training with an industrial robot T2 - 6th IEEE RAS/EMBS International Conference on Biomedical Robotics and Biomechatronics (BioRob) June 26-29, 2016. UTown, Singapore Y1 - 2016 U6 - http://dx.doi.org/10.1109/BIOROB.2016.7523750 SP - 950 EP - 955 ER - TY - JOUR A1 - Wollert, Jörg A1 - Booke, Andreas T1 - IoT von der Stange JF - elektronik N2 - Heute sollte am besten jedes Gerät in die große Rechnerwolke eingebettet werden. Doch so einfach ist das nicht, denn Cloud ist viel mehr als nur das Internet der Dinge. Als Anwender muss man sich also fragen, welche Dienste man möchte und welchem Anbieter man sein Vertrauen schenkt. KW - Einbetten in das Internet der Dinge Y1 - 2016 IS - 21 (2016) SP - 30 EP - 37 PB - WEKA-Fachmedien CY - München ER - TY - CHAP A1 - Kerpen, Nils B. A1 - Bung, Daniel B. A1 - Valero, Daniel A1 - Schlurmann, Torsten T1 - Energy dissipation within the wave run-up at stepped revetments T2 - 8th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering, Qingdao, China KW - energy disspation KW - wave run-up KW - friction Y1 - 2016 ER - TY - CHAP A1 - Bung, Daniel B. A1 - Valero, Daniel ED - Dewals, Benjamin T1 - Image processing techniques for velocity estimation in highly aerated flows: bubble image velocimetry vs. optical flow T2 - Sustainable Hydraulics in the Era of Global Change : Proceedings of the 4th IAHR Europe Congress (Liege, Belgium, 27-29 July 2016) Y1 - 2016 SN - 978-1-138-02977-4 SN - 978-1-4987-8149-7 (eBook) U6 - http://dx.doi.org/10.1201/b21902-31 SP - 151 EP - 157 PB - CRC Press ER - TY - JOUR A1 - Jahnke, Siegfried A1 - Roussel, Johanna A1 - Hombach, Thomas A1 - Kochs, Johannes A1 - Fischbach, Andreas A1 - Huber, Gregor A1 - Scharr, Hanno T1 - phenoSeeder - A robot system for automated handling and phenotyping of individual seeds JF - Plant physiology N2 - The enormous diversity of seed traits is an intriguing feature and critical for the overwhelming success of higher plants. In particular, seed mass is generally regarded to be key for seedling development but is mostly approximated by using scanning methods delivering only two-dimensional data, often termed seed size. However, three-dimensional traits, such as the volume or mass of single seeds, are very rarely determined in routine measurements. Here, we introduce a device named phenoSeeder, which enables the handling and phenotyping of individual seeds of very different sizes. The system consists of a pick-and-place robot and a modular setup of sensors that can be versatilely extended. Basic biometric traits detected for individual seeds are two-dimensional data from projections, three-dimensional data from volumetric measures, and mass, from which seed density is also calculated. Each seed is tracked by an identifier and, after phenotyping, can be planted, sorted, or individually stored for further evaluation or processing (e.g. in routine seed-to-plant tracking pipelines). By investigating seeds of Arabidopsis (Arabidopsis thaliana), rapeseed (Brassica napus), and barley (Hordeum vulgare), we observed that, even for apparently round-shaped seeds of rapeseed, correlations between the projected area and the mass of seeds were much weaker than between volume and mass. This indicates that simple projections may not deliver good proxies for seed mass. Although throughput is limited, we expect that automated seed phenotyping on a single-seed basis can contribute valuable information for applications in a wide range of wild or crop species, including seed classification, seed sorting, and assessment of seed quality. Y1 - 2016 U6 - http://dx.doi.org/10.1104/pp.16.01122 SN - 0032-0889 VL - 172 IS - 3 SP - 1358 EP - 1370 PB - Oxford University Press CY - Oxford ER - TY - JOUR A1 - Wrede, Oliver T1 - Continuity in travel information JF - Information Design Journal N2 - This article discusses the contrast between the information transportation companies provide to travellers and that of their brand messaging. Companies’ brand messaging often portrays the service they provide as pleasant, stress free and perfect. Customers and users of the service, on the other hand, often describe their experience of the service as a negative one. This article suggests that the brand value would be greater if transportation companies paid more attention to the users’ experience when designing their information systems, particularly in worst case scenarios. Y1 - 2016 U6 - http://dx.doi.org/10.1075/idj.22.2.09wre SN - 0142-5471 N1 - Gedruckt vorhanden in der Bereichsbibliothek Boxgraben unter 53 Z 971-2016 (Magazin) VL - 22 IS - 2 SP - 172 EP - 178 PB - John Benjamins CY - Amsterdam ER - TY - JOUR A1 - Reger, V. A1 - Döring, Bernd A1 - Kuhnhenne, M. T1 - Passive und aktive Maßnahmen zur Flächenkühlung im Stahl(leicht)bau JF - Bauingenieur N2 - Mit steigenden Dämmstandards und höheren Komfortanforderungen der Nutzer gerät die Problematik der sommerlichen Überhitzung zunehmend in den Fokus. Um die Überhitzung möglichst gering zu halten, sind Maßnahmen und Lösungen zu entwickeln, die den potenziellen Kühlbedarf eines Gebäudes vermeiden sowie reduzieren. Im Rahmen des europäischen Forschungsprojektes BATIMASS wurden Techniken untersucht, die die sommerliche Raumtemperatur ohne zusätzliche Kühlung (passiv) oder aber mit energieeffizienter wasserbasierter Flächenkühlung (aktiv) reduzieren und die besonders für Gebäude in Stahl(leicht)bauweise geeignet sind. Dafür wurde die Methodik der thermisch äquivalenten Decke weiterentwickelt, um das thermische Verhalten von Profilblechdecken in Gebäuden für beide Lösungsansätze analysieren zu können. Darüber hinaus wurde der Einsatz von Phasenwechselmaterial (PCM) zur Steigerung der Speicherfähigkeit von leichten Decken mit besonders geringer thermischer Masse in Simulationen sowie im Labor untersucht und bewertet. Y1 - 2016 U6 - http://dx.doi.org/10.37544/0005-6650-2016-07-08-63 SN - 0005-6650 N1 - gedruckt in der Bereichsbibliothek Bayernallee unter der Signatur 13 Z 049 VL - 91 IS - Jul/Aug SP - 309 EP - 316 PB - VDI Fachmedien CY - Düsseldorf ER - TY - JOUR A1 - Ferrein, Alexander A1 - Steinbauer, Gerald T1 - 20 Years of RoboCup - A Subjective Retrospection JF - KI - Künstliche Intelligenz N2 - This summer, RoboCup competitions were held for the 20th time in Leipzig, Germany. It was the second time that RoboCup took place in Germany, 10 years after the 2006 RoboCup in Bremen. In this article, we give an overview on the latest developments of RoboCup and what happened in the different leagues over the last decade. With its 20th edition, RoboCup clearly is a success story and a role model for robotics competitions. From our personal view point, we acknowledge this by giving a retrospection about what makes RoboCup such a success. Y1 - 2016 U6 - http://dx.doi.org/10.1007/s13218-016-0449-5 SN - 1610-1987 VL - 30 IS - 3 SP - 225 EP - 232 PB - Springer CY - Berlin ER -