TY - GEN A1 - Feldmann, Marco A1 - Francke, Gero A1 - Espe, Clemes A1 - Chen, Qian A1 - Baader, Fabian A1 - Boxberg, Marc S. A1 - Sustrate, Anna-Marie A1 - Kowalski, Julia A1 - Dachwald, Bernd T1 - Performance data of an ice-melting probe from field tests in two different ice environments N2 - This dataset was acquired at field tests of the steerable ice-melting probe "EnEx-IceMole" (Dachwald et al., 2014). A field test in summer 2014 was used to test the melting probe's system, before the probe was shipped to Antarctica, where, in international cooperation with the MIDGE project, the objective of a sampling mission in the southern hemisphere summer 2014/2015 was to return a clean englacial sample from the subglacial brine reservoir supplying the Blood Falls at Taylor Glacier (Badgeley et al., 2017, German et al., 2021). The standardized log-files generated by the IceMole during melting operation include more than 100 operational parameters, housekeeping information, and error states, which are reported to the base station in intervals of 4 s. Occasional packet loss in data transmission resulted in a sparse number of increased sampling intervals, which where compensated for by linear interpolation during post processing. The presented dataset is based on a subset of this data: The penetration distance is calculated based on the ice screw drive encoder signal, providing the rate of rotation, and the screw's thread pitch. The melting speed is calculated from the same data, assuming the rate of rotation to be constant over one sampling interval. The contact force is calculated from the longitudinal screw force, which es measured by strain gauges. The used heating power is calculated from binary states of all heating elements, which can only be either switched on or off. Temperatures are measured at each heating element and averaged for three zones (melting head, side-wall heaters and back-plate heaters). KW - Ocean Worlds KW - Icy Moons KW - Cryobot KW - Analogue Environments KW - Melting Efficiency KW - Melting Performance KW - Melting Probe KW - Ice Melting Y1 - 2022 U6 - https://doi.org/10.5281/zenodo.6094866 N1 - Forschungsdaten zu "Field-test performance of an ice-melting probe in a terrestrial analogue environment" (https://opus.bibliothek.fh-aachen.de/opus4/frontdoor/index/index/docId/10889) ER - TY - CHAP A1 - Veettil, Yadu Krishna Morassery A1 - Rakshit, Shantam A1 - Schopen, Oliver A1 - Kemper, Hans A1 - Esch, Thomas A1 - Shabani, Bahman ED - Bin Abdollah, Mohd Fadzli ED - Amiruddin, Hilmi ED - Singh, Amrik Singh Phuman ED - Munir, Fudhail Abdul ED - Ibrahim, Asriana T1 - Automated Control System Strategies to Ensure Safety of PEM Fuel Cells Using Kalman Filters T2 - Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia N2 - Having well-defined control strategies for fuel cells, that can efficiently detect errors and take corrective action is critically important for safety in all applications, and especially so in aviation. The algorithms not only ensure operator safety by monitoring the fuel cell and connected components, but also contribute to extending the health of the fuel cell, its durability and safe operation over its lifetime. While sensors are used to provide peripheral data surrounding the fuel cell, the internal states of the fuel cell cannot be directly measured. To overcome this restriction, Kalman Filter has been implemented as an internal state observer. Other safety conditions are evaluated using real-time data from every connected sensor and corrective actions automatically take place to ensure safety. The algorithms discussed in this paper have been validated thorough Model-in-the-Loop (MiL) tests as well as practical validation at a dedicated test bench. KW - control system KW - PEM fuel cells KW - Kalman filter Y1 - 2022 SN - 978-981-19-3178-9 SN - 978-981-19-3179-6 (E-Book) U6 - https://doi.org/10.1007/978-981-19-3179-6_55 SN - 2195-4356 N1 - 7th International Conference and Exhibition on Sustainable Energy and Advanced Material (ICE-SEAM 2021), Universiti Teknikal Malaysia Melaka (UTeM), Malaysia, in association with the Universitas Sebelas Maret (UNS), Indonesia, 23 November 2021 SP - 296 EP - 299 PB - Springer Nature CY - Singapore ER - TY - GEN A1 - Keimer, Jona A1 - Girbig, Leo A1 - Mayntz, Joscha A1 - Tegtmeyer, Philipp A1 - Wendland, Frederik A1 - Dahman, Peter A1 - Fisher, Alex A1 - Dorrington, Graham T1 - Flight mission optimization for eco-efficiency in consideration of electric regeneration and atmospheric conditions T2 - AIAA AVIATION 2022 Forum N2 - The development and operation of hybrid or purely electrically powered aircraft in regional air mobility is a significant challenge for the entire aviation sector. This technology is expected to lead to substantial advances in flight performance, energy efficiency, reliability, safety, noise reduction, and exhaust emissions. Nevertheless, any consumed energy results in heat or carbon dioxide emissions and limited electric energy storage capabilities suppress commercial use. Therefore, the significant challenges to achieving eco-efficient aviation are increased aircraft efficiency, the development of new energy storage technologies, and the optimization of flight operations. Two major approaches for higher eco-efficiency are identified: The first one, is to take horizontal and vertical atmospheric motion phenomena into account. Where, in particular, atmospheric waves hold exciting potential. The second one is the use of the regeneration ability of electric aircraft. The fusion of both strategies is expected to improve efficiency. The objective is to reduce energy consumption during flight while not neglecting commercial usability and convenient flight characteristics. Therefore, an optimized control problem based on a general aviation class aircraft has to be developed and validated by flight experiments. The formulated approach enables a development of detailed knowledge of the potential and limitations of optimizing flight missions, considering the capability of regeneration and atmospheric influences to increase efficiency and range. Y1 - 2022 U6 - https://doi.org/10.2514/6.2022-4118 N1 - AIAA AVIATION 2022 Forum, June 27-July 1, 2022 Chicago, IL & Virtual PB - AIAA CY - Reston, Va. ER - TY - GEN A1 - Braun, Lena A1 - Krafft, Simone A1 - Tippkötter, Nils T1 - Combined supercritical carbon dioxide extraction and chromatography of the algae fatty linoleic and linolenic acid T2 - Chemie Ingenieur Technik N2 - A method for the integrated extraction and separation of fatty acids from algae using supercritical CO2 is presented. Desmodesmus obliquus and Chlorella sorokiniana were used as algae. First, a method for chromatographic separation of fatty acids of different degrees of saturation was established and optimized. Then, an integrated method for supercritical extraction was developed for both algal species. It was also verified whether prior cell disruption was beneficial for extraction. In developing the method for chromatographic separation, statistical experimental design was used to determine the optimal parameter settings. The methanol content in the mobile phase proved to be the most important parameter for successful separation of the three unsaturated fatty acids oleic acid, linoleic acid, and linolenic acid. Supercritical extraction with dried algae showed that about four times more fatty acids can be extracted from C. sorokiniana relative to the dry mass used. Y1 - 2022 U6 - https://doi.org/10.1002/cite.202255308 SN - 0009-286X SN - 1522-2640 (eISSN) N1 - ProcessNet and DECHEMA‐BioTechNet Jahrestagungen 2022 together with 13th ESBES Symposium 2022, 12. - 15. September 2022, Eurogress Aachen VL - 94 IS - 9 SP - 1304 PB - Wiley-VCH CY - Weinheim ER - TY - JOUR A1 - Penner, Crystal A1 - Usherovich, Samuel A1 - Niedermeier, Jana A1 - Bélanger-Champagne, Camille A1 - Trinczek, Michael A1 - Paulßen, Elisabeth A1 - Hoehr, Cornelia T1 - Organic Scintillator-Fibre Sensors for Proton Therapy Dosimetry: SCSF-3HF and EJ-260 JF - electronics N2 - In proton therapy, the dose from secondary neutrons to the patient can contribute to side effects and the creation of secondary cancer. A simple and fast detection system to distinguish between dose from protons and neutrons both in pretreatment verification as well as potentially in vivo monitoring is needed to minimize dose from secondary neutrons. Two 3 mm long, 1 mm diameter organic scintillators were tested for candidacy to be used in a proton–neutron discrimination detector. The SCSF-3HF (1500) scintillating fibre (Kuraray Co. Chiyoda-ku, Tokyo, Japan) and EJ-260 plastic scintillator (Eljen Technology, Sweetwater, TX, USA) were irradiated at the TRIUMF Neutron Facility and the Proton Therapy Research Centre. In the proton beam, we compared the raw Bragg peak and spread-out Bragg peak response to the industry standard Markus chamber detector. Both scintillator sensors exhibited quenching at high LET in the Bragg peak, presenting a peak-to-entrance ratio of 2.59 for the EJ-260 and 2.63 for the SCSF-3HF fibre, compared to 3.70 for the Markus chamber. The SCSF-3HF sensor demonstrated 1.3 times the sensitivity to protons and 3 times the sensitivity to neutrons as compared to the EJ-260 sensor. Combined with our equations relating neutron and proton contributions to dose during proton irradiations, and the application of Birks’ quenching correction, these fibres provide valid candidates for inexpensive and replicable proton-neutron discrimination detectors Y1 - 2022 U6 - https://doi.org/10.3390/electronics12010011 SN - 2079-9292 N1 - This article belongs to the Special Issue "Applications of Optical Fiber Sensors" VL - 12 IS - 1 PB - MDPI CY - Basel ER - TY - JOUR A1 - Finkenberger, Isabel Maria T1 - Strukturwandel als transformative Wende JF - disP: The Planning Review Y1 - 2024 U6 - https://doi.org/10.1080/02513625.2022.2158603 SN - 0251-3625 VL - 58 IS - 3 SP - 86 EP - 94 PB - Taylor & Francis CY - Abingdon ER - TY - JOUR A1 - Ojovan, Michael I. A1 - Steinmetz, Hans-Jürgen T1 - Approaches to Disposal of Nuclear Waste JF - Energies N2 - We present a concise mini overview on the approaches to the disposal of nuclear waste currently used or deployed. The disposal of nuclear waste is the end point of nuclear waste management (NWM) activities and is the emplacement of waste in an appropriate facility without the intention to retrieve it. The IAEA has developed an internationally accepted classification scheme based on the end points of NWM, which is used as guidance. Retention times needed for safe isolation of waste radionuclides are estimated based on the radiotoxicity of nuclear waste. Disposal facilities usually rely on a multi-barrier defence system to isolate the waste from the biosphere, which comprises the natural geological barrier and the engineered barrier system. Disposal facilities could be of a trench type, vaults, tunnels, shafts, boreholes, or mined repositories. A graded approach relates the depth of the disposal facilities’ location with the level of hazard. Disposal practices demonstrate the reliability of nuclear waste disposal with minimal expected impacts on the environment and humans. KW - borehole disposal KW - geological disposal KW - disposal facility KW - retention time KW - nuclear waste Y1 - 2022 U6 - https://doi.org/10.3390/en15207804 SN - 1996-1073 N1 - This article belongs to the Special Issue "Treatment of Radioactive Waste and Sustainability Energy" VL - 15 IS - 20 PB - MDPI CY - Basel ER - TY - CHAP A1 - Moorkamp, Wilfried A1 - Peterson, Leif Arne A1 - Uibel, Thomas ED - Fouad, Nabil A. T1 - Nachhaltige Holzbrücken für Geh- und Radwege T2 - Bauphysik Kalender 2022: Holzbau, 22. Jahrgang N2 - Am Lehr- und Forschungsgebiet Holzbau der Fachhochschule Aachen wurden im Rahmen des Forschungsvorhabens „Nachhaltige Standardbrücken in Holzbauweise“ Standardtypen für Geh- und Radwegbrücken entwickelt. Die Brücken sind durch konsequente Umsetzungen von Maßnahmen des konstruktiven Holzschutzes für eine Nutzung von mehr als 80~Jahren konzipiert. Innovative Lösungen für Bauteile und Anschlüsse sowie Materialalternativen im Bereich des Belages und der Geländer ermöglichen eine wartungsarme Konstruktion und tragen somit zur Wirtschaftlichkeit und Nachhaltigkeit bei. Um den Einsatz der entwickelten Standardbrückentypen in der Praxis zu erleichtern, wurden Leistungsverzeichnisse, Musterstatiken, Musterzeichnungen und umfangreiche Detailkataloge als Unterstützung für Planer und Bauherren erstellt. Damit die Randbedingungen für eine lange Lebensdauer während der Nutzung der Brücke erhalten bleiben, wurden Leitfäden für die Pflege und Wartung sowie für die Brückenprüfung erarbeitet. Der Beitrag gibt Einblicke in das Forschungsvorhaben und seine Resultate. Y1 - 2022 SN - 9783433033609 (Print) SN - 9783433611081 (Online) U6 - https://doi.org/10.1002/9783433611081.ch17 SP - 574 EP - 592 PB - Ernst & Sohn CY - Berlin ER - TY - JOUR A1 - Schulte-Tigges, Joschua A1 - Förster, Marco A1 - Nikolovski, Gjorgji A1 - Reke, Michael A1 - Ferrein, Alexander A1 - Kaszner, Daniel A1 - Matheis, Dominik A1 - Walter, Thomas T1 - Benchmarking of various LiDAR sensors for use in self-driving vehicles in real-world environments JF - Sensors N2 - Abstract In this paper, we report on our benchmark results of the LiDAR sensors Livox Horizon, Robosense M1, Blickfeld Cube, Blickfeld Cube Range, Velodyne Velarray H800, and Innoviz Pro. The idea was to test the sensors in different typical scenarios that were defined with real-world use cases in mind, in order to find a sensor that meet the requirements of self-driving vehicles. For this, we defined static and dynamic benchmark scenarios. In the static scenarios, both LiDAR and the detection target do not move during the measurement. In dynamic scenarios, the LiDAR sensor was mounted on the vehicle which was driving toward the detection target. We tested all mentioned LiDAR sensors in both scenarios, show the results regarding the detection accuracy of the targets, and discuss their usefulness for deployment in self-driving cars. KW - Lidar KW - Benchmark KW - Self-driving Y1 - 2022 U6 - https://doi.org/10.3390/s22197146 SN - 1424-8220 N1 - This article belongs to the Special Issue "Sensor Fusion for Vehicles Navigation and Robotic Systems" VL - 22 IS - 19 PB - MDPI CY - Basel ER - TY - JOUR A1 - Finkenberger, Isabel Maria T1 - Transformatives Forschen, Lehren und Handeln im Rheinischen Braunkohlerevier JF - Forum Wohnen und Stadtentwicklung N2 - Die Institution Hochschule hat das Potenzial, über transformatives Forschen und Lehren und den entsprechenden Wissenstransfer in den lokalen Kontext strategisch-verlässliche Partnerin der Großen Transformation zur Nachhaltigkeit zu werden und bei der Ausbildung von Pionierinnen und Pionieren des Wandels mitzuwirken. Der Lehr- und Forschungsschwerpunkt „Zukunftsfähige Transformation” am Fachbereich Architektur der FH Aachen widmet sich seit 2020 dem Tagebauumfeld Hambach im Rheinischen Revier, um dort angewandt und in Kooperation neue Narrative, innovative Prozesse, ortsbezogene Konzepte und strategische Projekte zu entwickeln und umzusetzen. Y1 - 2024 SN - 1439-7242 VL - 2022 IS - 2 SP - 69 EP - 72 PB - vhw CY - Berlin ER - TY - CHAP A1 - Golland, Alexander ED - Riechert, Anne ED - Wilmer, Thomas T1 - Kommentierung von § 7 Telekommunikation-Telemedien-Datenschutzgesetz T2 - TTDSG Y1 - 2022 SN - 978-3-503-20978-1 N1 - Gedruckte Ausgabe unter 21 QRUG 2 verfügbar. SP - 145 EP - 151 PB - Erich Schmidt CY - Berlin ER - TY - CHAP A1 - Finkenberger, Isabel Maria ED - Pufke, Andrea T1 - Räumliche Transformation als Planungsaufgabe T2 - Zurück in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier Y1 - 2024 N1 - Mitteilungen aus dem LVR-Amt für Denkmalpflege im Rheinland 39 : Zurück in die Zukunft. Denkmalpflege und Strukturwandel im Rheinischen Revier. Dokumentation zum 7. Rheinischen Tag für Denkmalpflege in Morschenich, 2. Juni 2022 SP - 70 EP - 77 PB - LVR-Amt für Denkmalpflege im Rheinland CY - Pulheim ER - TY - BOOK A1 - Laack, Walter van T1 - Schnittstelle Tod: Was lernen wir durch Corona über Leben und Tod? Y1 - 2022 SN - 978-3-936624-53-3 N1 - Siebter Tagungsband aus der Buchreihe “Schnittstelle Tod” PB - van Laack GmbH CY - Aachen ER - TY - CHAP A1 - Crookston, Brian M. A1 - Bung, Daniel Bernhard ED - Ortega-Sánchez, Miguel T1 - Application of RGB-D cameras in hydraulic laboratory studies T2 - Proceedings of the 39th IAHR World Congress N2 - Non-intrusive measuring techniques have attained a lot of interest in relation to both hydraulic modeling and prototype applications. Complimenting acoustic techniques, significant progress has been made for the development of new optical methods. Computer vision techniques can help to extract new information, e. g. high-resolution velocity and depth data, from videos captured with relatively inexpensive, consumer-grade cameras. Depth cameras are sensors providing information on the distance between the camera and observed features. Currently, sensors with different working principles are available. Stereoscopic systems reference physical image features (passive system) from two perspectives; in order to enhance the number of features and improve the results, a sensor may also estimate the disparity from a detected light to its original projection (active stereo system). In the current study, the RGB-D camera Intel RealSense D435, working on such stereo vision principle, is used in different, typical hydraulic modeling applications. All tests have been conducted at the Utah Water Research Laboratory. This paper will demonstrate the performance and limitations of the RGB-D sensor, installed as a single camera and as camera arrays, applied to 1) detect the free surface for highly turbulent, aerated hydraulic jumps, for free-falling jets and for an energy dissipation basin downstream of a labyrinth weir and 2) to monitor local scours upstream and downstream of a Piano Key Weir. It is intended to share the authors’ experiences with respect to camera settings, calibration, lightning conditions and other requirements in order to promote this useful, easily accessible device. Results will be compared to data from classical instrumentation and the literature. It will be shown that even in difficult application, e. g. the detection of a highly turbulent, fluctuating free-surface, the RGB-D sensor may yield similar accuracy as classical, intrusive probes. Y1 - 2022 SN - 978-90-832612-1-8 U6 - https://doi.org/10.3850/IAHR-39WC252171192022964 SN - 2521-7119 (print) SN - 2521-716X (online) N1 - 39th IAHR World Congress, 19. - 24. Juni 2022, Granada SP - 5127 EP - 5133 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - JOUR A1 - Pourshahidi, Ali Mohammad A1 - Achtsnicht, Stefan A1 - Offenhäusser, Andreas A1 - Krause, Hans-Joachim ED - Offenhäusser, Andreas T1 - Frequency Mixing Magnetic Detection Setup Employing Permanent Ring Magnets as a Static Offset Field Source JF - Sensors N2 - Frequency mixing magnetic detection (FMMD) has been explored for its applications in fields of magnetic biosensing, multiplex detection of magnetic nanoparticles (MNP) and the determination of core size distribution of MNP samples. Such applications rely on the application of a static offset magnetic field, which is generated traditionally with an electromagnet. Such a setup requires a current source, as well as passive or active cooling strategies, which directly sets a limitation based on the portability aspect that is desired for point of care (POC) monitoring applications. In this work, a measurement head is introduced that involves the utilization of two ring-shaped permanent magnets to generate a static offset magnetic field. A steel cylinder in the ring bores homogenizes the field. By variation of the distance between the ring magnets and of the thickness of the steel cylinder, the magnitude of the magnetic field at the sample position can be adjusted. Furthermore, the measurement setup is compared to the electromagnet offset module based on measured signals and temperature behavior. KW - magnetic sensors KW - biosensors KW - frequency mixing magnetic detection KW - magnetic nanoparticles Y1 - 2022 U6 - https://doi.org/10.3390/s22228776 SN - 1424-8220 VL - 22 IS - 22 PB - MDPI CY - Basel ER - TY - THES A1 - Lawrenz, Anne Murielle T1 - Lebens.Mittel.Punkt : Konzeption und Gestaltung einer Anwendung für Ernährungsberatung N2 - „kocotte“ (eine Abwandlung eines kleinen Kochtopfs) soll drei aktuelle ­Ernährungstrends kombinieren: Gesundheit, Nachhaltigkeit und Genuss. Der Markt bietet viele Angebote, die einen oder auch zwei Themen kombinieren – von Special-Interest-Publikationen über Diätprogramme bis hin zu Foodvereinigungen – alle mit Daseinsberechtigung. Will oder muss ich aber beispielsweise meine Essgewohnheiten umstellen, gibt es kein überzeugendes Werkzeug, das mir alle drei Themen zusammenfasst. Hier soll „kocotte“ ein neues Angebot machen. KW - Ernährung KW - Genuss KW - Nachhaltigkeit KW - Geschmack KW - Gesundheit Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Lenz, Lena T1 - Frauen sind der Boss : eine Kampagne für mehr Gleichberechtigung in Führungspositionen N2 - Man könnte vermuten, dass in einem so weit entwickelten Land wie Deutschland Geschlechterdiskriminierung bereits erfolgreich überwunden wurde – doch das entspricht nicht der Realität. Besonders in Führungspositionen fällt dieses Ungleichgewicht auf. Eine Ursache dafür ist das historisch etablierte Rollenverständnis, aber auch vonseiten der Frauen gibt es häufig ein grundlegendes Problem: Sie trauen sich zu wenig zu. Die Kampagne soll junge Frauen dazu motivieren, ihre beruflichen Ambitionen hoch anzusetzen und zielstrebig zu verfolgen. Das Online-Portal "femiverse" ist dabei ihr Wegbereiter. Es ermöglicht einen direkten Austausch mit anderen Nutzer:innen und eröffnet durch Workshops mit Unternehmer:innen neue Perspektiven. Die Bezeichnung „Powerfrau“ ist überholt – Frauen in Führungspositionen sind keine Ausnahmetalente, sie sind die Normalität von morgen. KW - Kampagne KW - Geschlechtergerechtigkeit KW - Gleichberechtigung KW - Frauen KW - Beruf Y1 - 2022 PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kaspor, Alexej T1 - Kritik der digitalen Rationalisierung N2 - Digitalisierung macht’s möglich: mittlerweile beziehen sich Designer:innen in ihrer Konzeptentwicklung immer häufiger auf Referenzdesigns. Sie picken sich die Eigenschaften aus ihnen heraus, von denen sie sich die größte Marktfähigkeit versprechen, und basteln sie zu einem neuen Produkt zusammen. Voilà. Doch wie unkonventionell kann Design noch sein? Wie viel Luft bleibt der Kreativität unter dem immer enger geschnürten Korsett der Marktfähigkeit? Alexej Kaspor eröffnet die Diskussion mit einem provokanten Projekt, das einen kritischen Blick in die Zukunft des Industriedesigns wirft. Dazu fasst er gängige Designprogramme in einer Software zusammen und verbindet sie mit einer künstlichen Intelligenz, die die aktuelle Entwicklung digital rationalisieren und auf die Spitze treiben soll. Diese führt Meta-Analysen über das Nutzungsverhalten durch und prüft damit Frameworks von Referenzdesigns auf ihre Vermarktbarkeit. Aus diesen entwickelt sie dann Gestaltungsvorschläge, ohne beim Seiltanz zwischen Trendhörigkeit und Scheinindividualismus aus dem Gleichgewicht zu kommen. Innerhalb von Sekunden werden den Designer:innen perfekte Vorschläge übers Metaverse simuliert. Auf dem Silbertablett serviert, übersichtlich und gefährlich einfach. Bereit, kombiniert und in Produktion gebracht zu werden. Auch mit dem Tracking der KI kann niemand mithalten: um immer am Puls der Zeit zu bleiben, benachrichtigt sie die Designer:innen in Echtzeit über die neuesten Innovationen und Trends. Ressourcenraubendes Herumprobieren in CAD-Programmen gehört also der Vergangenheit an. Das Programm schafft Abhilfe, und verspricht dabei auch noch die höchste Effizienz, konkret: garantiertes Kapital. Schlagende Argumente, die die Schwächen der Konsumgesellschaft und Kommerzialisierung gezielt ausgenutzen. Es entsteht die perfekte Marketingmaßnahme, ein genialer Treiber für den Turbokapitalismus. Kram, den niemand braucht und zynische Statussymbole inklusive. Der Stolz der geltungsbedürftigen Designer:innen wird dabei selbstverständlich nicht untergraben. Sie sollen mitziehen. Mit zahlreichen Notches wird der Erfolg und die Konkurrenzfähigkeit des Produkts prognostiziert und ihnen Honig ums Maul geschmiert. Die beklemmende Vorahnung wird sich bestätigen. Schritt für Schritt enteignet die KI den Designer:innen ihre Kreativität, bis sie nicht mehr sind als die Kurator:innen berechenbarer Produktkonzepte. Der Spätkapitalismus hat sie in der Mangel. Versprochen: diese Arbeit lässt niemanden kalt. KW - Digitalisierung KW - Designprogramme KW - Nutzungsverhalten KW - Marktfähigkeit KW - künstliche Intelligenz Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Lebrecht, Rike-Charlotte T1 - Inga : ein modulares hydroponisches System für Endverbraucher N2 - In dieser Arbeit wurde sich mit der Frage auseinandergesetzt, wie sich der Nahrungsmittelanbau im urbanen Raum entwickeln könnte. Eine spannende Alternative zu traditionellen Anbaumethoden ist die Hydroponik, der Anbau von Pflanzen ohne Erde. Basierend auf dieser Technologie wurde in diesem Projekt ein Indoor-Garden-System gestaltet, welches den Nahrungsmittelanbau zurück zur Verbraucher:In bringt und zu einem bewussteren Umgang mit Lebensmitteln anregen soll. Denn mit „INGA“ kann frisches, pestizidfreies Blattgemüse ganz einfach zu Hause selbst angebaut werden. Das hydroponische System schafft mithilfe einer Nährstofflösung und künstlichem Licht optimale Wachstumsbedingungen für die Pflanzen – ganz unabhängig von örtlichen Gegebenheiten. Mithilfe seiner Modularität können Nutzer:Innen „INGA“ nach Belieben konfigurieren. Damit wird es einer breiten Zielgruppe mit unterschiedlichen Bedürfnissen gerecht und ermöglicht pestizidfreie Nahrung – auch in den Städten. KW - Urban KW - Hydroponik KW - Frisches Gemüse KW - Produktdesign KW - Industriedesign Y1 - 2022 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kannengießer, Justine T1 - Vom Airbag zum Rucksack mit Upcycling : Kampagne zur Steigerung der Bekanntheit der Marke Airpaq N2 - In der Automobilindustrie entsteht ein enormes Ausmaß an Abfall. Genau an dieser Stelle greift das Kölner Start-up Airpaq ein, das nachhaltige Rucksäcke und Accessoires aus Autoschrott unter fairen Arbeitsbedingungen in der EU herstellt. Das Ziel der Kampagne ist es, die Markenbekanntheit zu steigern und eine tiefergreifende und lang anhaltende Verbindung zur jungen Zielgruppe aufzubauen. Genau so, wie Airpaq den Taschen-Markt revolutioniert, stellt auch die junge Zielgruppe immer wieder Altbewährtes infrage. Mit der „HOLYSCRAP“-Bewegung ruft die Kampagne Upcycling-Abenteuer ins Leben. Die Kampagne ermutigt dazu, Teil der Upcycling-Community zu werden, um immer wieder neu und anders "schrottastische" Erlebnisse zu entdecken. So soll eingeladen werden, nicht nur beim Griff zur Tasche mal etwas Neues auszuprobieren, sondern auch bei allen gemeinsamen Aktivitäten, die man mit Airpaq erlebt. KW - Airpaq KW - Automobilbranche KW - nachhaltig KW - Kampagne KW - Rucksack Y1 - 2022 PB - FH Aachen CY - Aachen ER -