TY - CHAP A1 - Altherr, Lena A1 - Conzen, Max A1 - Elsen, Ingo A1 - Frauenrath, Tobias A1 - Lyrmann, Andreas ED - Reiff-Stephan, Jörg ED - Jäkel, Jens ED - Schwarz, André T1 - Sensor retrofitting of existing buildings in an interdisciplinary teaching project at university level T2 - Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel N2 - Existing residential buildings have an average lifetime of 100 years. Many of these buildings will exist for at least another 50 years. To increase the efficiency of these buildings while keeping costs at reasonable rates, they can be retrofitted with sensors that deliver information to central control units for heating, ventilation and electricity. This retrofitting process should happen with minimal intervention into existing infrastructure and requires new approaches for sensor design and data transmission. At FH Aachen University of Applied Sciences, students of different disciplines work together to learn how to design, build, deploy and operate such sensors. The presented teaching project already created a low power design for a combined CO2, temperature and humidity measurement device that can be easily integrated into most home automation systems KW - Building Automation KW - Smart Building KW - CO2 KW - Carbon Dioxide KW - Education Y1 - 2023 SN - 978-3-910103-01-6 U6 - https://doi.org/10.33968/2023.04 N1 - 19. AALE-Konferenz. Luxemburg, 08.03.-10.03.2023. BTS Connected Buildings & Cities Luxemburg (Tagungsband unter https://doi.org/10.33968/2023.01) SP - 31 EP - 40 PB - le-tex publishing services GmbH CY - Leipzig ER - TY - CHAP A1 - Schulte, Jonas A1 - Schwager, Christian A1 - Noureldin, Kareem A1 - May, Martin A1 - Teixeira Boura, Cristiano José A1 - Herrmann, Ulf T1 - Gradient controlled startup procedure of a molten-salt power-to-heat energy storage plant based on dynamic process simulation T2 - SolarPACES: Solar Power & Chemical Energy Systems N2 - The integration of high temperature thermal energy storages into existing conventional power plants can help to reduce the CO2 emissions of those plants and lead to lower capital expenditures for building energy storage systems, due to the use of synergy effects [1]. One possibility to implement that, is a molten salt storage system with a powerful power-to-heat unit. This paper presents two possible control concepts for the startup of the charging system of such a facility. The procedures are implemented in a detailed dynamic process model. The performance and safety regarding the film temperatures at heat transmitting surfaces are investigated in the process simulations. To improve the accuracy in predicting the film temperatures, CFD simulations of the electrical heater are carried out and the results are merged with the dynamic model. The results show that both investigated control concepts are safe regarding the temperature limits. The gradient controlled startup performed better than the temperature-controlled startup. Nevertheless, there are several uncertainties that need to be investigated further. KW - Power plants KW - Energy storage KW - Associated liquids Y1 - 2023 SN - 978-0-7354-4623-6 U6 - https://doi.org/10.1063/5.0148741 SN - 1551-7616 (online) SN - 0094-243X (print) N1 - SolarPACES: SOLAR POWER & CHEMICAL ENERGY SYSTEMS: 27th International Conference on Concentrating Solar Power and Chemical Energy Systems, 27 September–1 October 2021, Online IS - 2815 / 1 PB - AIP conference proceedings / American Institute of Physics CY - Melville, NY ER - TY - THES A1 - Herrmann, Luna T1 - Blind Shopping N2 - Das Einkaufen in Einkaufszentren oder Ladenstraßen ist für Menschen ohne Sehbehinderung eine selbstverständliche Tätigkeit. Für Menschen mit Sehbehinderung gibt es bis heute keine Möglichkeit, sich ohne Hilfe von Familienmitgliedern, Freund:innen oder Pflegepersonal in einem Einkaufszentrum zurechtzufinden. Genau dieses Problem löst "NAVON.". Er ist ein intelligenter und smarter Blindenstock, welcher durch Ultraschalldistanzsensoren frühzeitig Hindernisse erkennt und die Möglichkeit bietet, den Betroffenen durch das Einkaufszentrum zu lotsen. Die Logik des Systems liegt innerhalb des Handgriffs, welcher die wichtigsten Einstellungen bzgl. Sprache und haptischer Bedienelemente steuert. Ebenfalls gibt er dem Betroffenen auch ein haptisches Feedback, um Hindernisse frühzeitig umgehen zu können. "NAVON." ist ein wichtiger Ansatz für eine neue Kategorie von Produkten und Blindenstöcken. Darüber hinaus birgt das Konzept auch weitere Potenziale für öffentliche Gebäude (Ämter, Krankenhäuser, etc..). KW - Inklusion KW - Sehbehinderung KW - Einkaufen KW - Hindernisse KW - Blindenstock Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Begas, Philipp T1 - Modulares Regalsystem : Stauraummöbel für den Bereich Office / Homeoffice N2 - Das modulare Regalsystem „MORÉ“ ist ein Stauraummöbel, welches sich im Bereich des (Home) Office einordnet. Das Produkt dient zur Aufbewahrung von Büromaterialien und verbessert die Geräuschkulisse sowie die Beschaffenheit am Arbeitsplatz. Die potenzielle Käufergruppe befindet sich im Alter von 25-67 Jahren, im gewöhnlichen Arbeitsalter Zeitraum (obere Mittelschicht). Im Fokus des Regalsystems steht der besonders freundliche Auf- und Abbau, welcher werkzeuglos erfolgt. Es ist in verschiedene Richtungen erweiterbar (Steckverbindung) und bietet unendlichen Spielraum der Gestaltung. Durch verschiedenfarbige Kennzeichnungen bietet das Regal ein Ordnungssystem, wodurch schnelleres Finden und Sortieren von Unterlagen möglich ist (Grundordnung). Die Rückwände dienen neben der Stabilität als Akustik-/ und Sichtschutz. Das Produkt passt sich jeder Raumsituation individuell an. Ist „MORÉ“ dein nächstes Regalsystem? KW - Modular KW - Steckverbindung KW - Office KW - Erweiterbar KW - Benutzerfreundlich Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - THES A1 - Kappel, Jana Naomi T1 - KLIKK : ein smartes Kinderprodukt für den altersgerechten Einstieg in die digitale Welt N2 - Die neue Generation wird mit einer Medienwelt konfrontiert, welche nicht auf unsere kleinen Nutzer:innen ausgelegt ist. Die Verwendung von digitalen Medien hatte nie einen größeren Einfluss auf unsere Gesellschaft wie im Hier und Jetzt. Somit ist es von großer Relevanz, diese Nutzung kindergerechter zu gestalten und einen sicheren Rahmen für sie zu schaffen. Das Bachelorprojekt „KLIKK“ legt einen Lösungsentwurf für den altersgerechten Einstieg für Kinder in diese digitale Welt vor, um den richtigen Umgang mit Smartwatches und darauf aufbauende Medien zu ermöglichen und gleichzeitig einen pädagogischen Mehrwert zu bieten. Das didaktische Produktkonzept, welches explizit für Kinder designed wurde, beinhaltet das Erlernen des Uhrlesens und befriedigt das aufkommende Bedürfnis nach Vernetzung in einem sicheren System. Zudem fördert es die Autonomie und ist an die kindliche Motorik angepasst. Mitinitiator und Namensgeber für diese Konzeption ist die deutsche Kinderuhrenmarke KWIO. KLIKK inkludiert Sicherheit, die Freude am Lernen und bietet eine Möglichkeit, die Kleinen ganz groß in unsere digitale Welt aufzunehmen. KW - Smartwatch KW - conceptual design KW - industrial design KW - children Y1 - 2023 PB - FH Aachen CY - Aachen ER - TY - JOUR A1 - Hammer, Thorben A1 - Quitter, Julius A1 - Mayntz, Joscha A1 - Bauschat, J.-Michael A1 - Dahmann, Peter A1 - Götten, Falk A1 - Hille, Sebastian A1 - Stumpf, Eike T1 - Free fall drag estimation of small-scale multirotor unmanned aircraft systems using computational fluid dynamics and wind tunnel experiments JF - CEAS Aeronautical Journal N2 - New European Union (EU) regulations for UAS operations require an operational risk analysis, which includes an estimation of the potential danger of the UAS crashing. A key parameter for the potential ground risk is the kinetic impact energy of the UAS. The kinetic energy depends on the impact velocity of the UAS and, therefore, on the aerodynamic drag and the weight during free fall. Hence, estimating the impact energy of a UAS requires an accurate drag estimation of the UAS in that state. The paper at hand presents the aerodynamic drag estimation of small-scale multirotor UAS. Multirotor UAS of various sizes and configurations were analysed with a fully unsteady Reynolds-averaged Navier–Stokes approach. These simulations included different velocities and various fuselage pitch angles of the UAS. The results were compared against force measurements performed in a subsonic wind tunnel and provided good consistency. Furthermore, the influence of the UAS`s fuselage pitch angle as well as the influence of fixed and free spinning propellers on the aerodynamic drag was analysed. Free spinning propellers may increase the drag by up to 110%, depending on the fuselage pitch angle. Increasing the fuselage pitch angle of the UAS lowers the drag by 40% up to 85%, depending on the UAS. The data presented in this paper allow for increased accuracy of ground risk assessments. KW - Multirotor UAS KW - Drag estimation KW - CFD KW - Wind tunnel experiments KW - Wind milling Y1 - 2023 U6 - https://doi.org/10.1007/s13272-023-00702-w SN - 1869-5590 (Online) SN - 1869-5582 (Print) N1 - Corresponding author: Thorben Hammer PB - Springer CY - Wien ER - TY - THES A1 - Williams, Vivian T1 - Entwicklung eines neuen Erscheinungsbildes für Die Staatliche Antikensammlung in München N2 - Die Staatliche Antikensammlung in München ist eine antike Kunstsammlung, bestehend aus zwei Kunsthäusern. Das Haus der Glyptothek befindet sich auf der Nordseite und die Antikensammlung auf der Südseite des Königsplatzes. Während die Glyptothek Skulpturen ausstellt, zeigt die Antikensammlung Gebrauchsgegenstände und Objekte aus der etruskischen, griechischen und römischen Epoche. Sie gehört mit ihrer Kunstsammlung zu den weltweit führenden ihrer Art. In seinem Vorhaben, das Kulturerbe zu wahren, legt das Museum besonders hohen Wert auf Bildung und Vermittlung. Um dies langfristig zu gewährleisten, ist ein ausgeglichenes Erscheinungsbild zwischen Klassik und Modernität unentbehrlich. Die griechische Stilepoche zeichnet sich in ihrer abstrakten Nutzung von geometrischen Grundformen aus. Im Zusammenspiel von geometrischen Formen und Abstrahierungen entsteht ein neues Erscheinungsbild. KW - Klassizismus KW - Modernität KW - Abstrahierung KW - Kunstsammlung KW - Griechisch Y1 - 2023 N1 - Für diese Arbeit steht kein Volltext zur Verfügung. PB - FH Aachen CY - Aachen ER - TY - CHAP A1 - Bung, Daniel Bernhard A1 - Langohr, Phillip A1 - Waldenberger, Lisa ED - Habersack, Helmut ED - Tritthart, Michael T1 - Influence of cycle number in CFD studies of labyrinth weirs T2 - Proceedings of the 40th IAHR World Congress (Vienna, 2023) N2 - The major advantage of labyrinth weirs over linear weirs is hydraulic efficiency. In hydraulic modeling efforts, this strength contrasts with limited pump capacity as well as limited computational power for CFD simulations. For the latter, reducing the number of investigated cycles can significantly reduce necessary computational time. In this study, a labyrinth weir with different cycle numbers was investigated. The simulations were conducted in FLOW-3D HYDRO as a Large Eddy Simulation. With a mean deviation of 1.75 % between simulated discharge coefficients and literature design equations, a reasonable agreement was found. For downstream conditions, overall consistent results were observed as well. However, the orientation of labyrinth weirs with a single cycle should be chosen carefully under consideration of the individual research purpose. KW - CFD KW - Large Eddy Simulation KW - Labyfrinth weirs Y1 - 2023 SN - 978-90-833476-1-5 U6 - https://doi.org/10.3850/978-90-833476-1-5_iahr40wc-p0531-cd SN - L 2521-7119 (online) N1 - Vienna, Austria, from August 21 to 25, 2023 PB - International Association for Hydro-Environment Engineering and Research (IAHR) CY - Madrid ER - TY - JOUR A1 - Janus, Kevin Alexander A1 - Achtsnicht, Stefan A1 - Drinic, Aleksander A1 - Kopp, Alexander A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Transient magnesium-based thin-film temperature sensor on a flexible, bioabsorbable substrate for future medical applications JF - Applied Research N2 - In this work, the bioabsorbable materials, namely fibroin, polylactide acid (PLA), magnesium and magnesium oxide are investigated for their application as transient, resistive temperature detectors (RTD). For this purpose, a thin-film magnesium-based meander-like electrode is deposited onto a flexible, bioabsorbable substrate (fibroin or PLA) and encapsulated (passivated) by additional magnesium oxide layers on top and below the magnesium-based electrode. The morphology of different layered RTDs is analyzed by scanning electron microscopy. The sensor performance and lifetime of the RTD is characterized both under ambient atmospheric conditions between 30°C and 43°C, and wet tissue-like conditions with a constant temperature regime of 37°C. The latter triggers the degradation process of the magnesium-based layers. The 3-layers RTDs on a PLA substrate could achieve a lifetime of 8.5 h. These sensors also show the best sensor performance under ambient atmospheric conditions with a mean sensitivity of 0.48 Ω/°C ± 0.01 Ω/°C. KW - Silk fibroin KW - Polylactide acid KW - Bioabsorbable KW - Resistive temperature detector Y1 - 2023 U6 - https://doi.org/10.1002/appl.202300102 SN - 2702-4288 (Print) N1 - Corresponding author: Michael Josef Schöning IS - Accepted manuscript PB - Wiley-VCH ER - TY - JOUR A1 - Janus, Kevin Alexander A1 - Achtsnicht, Stefan A1 - Tempel, Laura A1 - Drinic, Aleksaner A1 - Kopp, Alexander A1 - Keusgen, Michael A1 - Schöning, Michael Josef T1 - Influence of fibroin membrane composition and curing parameters on the performance of a biodegradable enzymatic biosensor manufactured from Silicon-Free Carbon JF - Physica status solidi : pss. A, Applications and materials science N2 - Herein, fibroin, polylactide (PLA), and carbon are investigated for their suitability as biocompatible and biodegradable materials for amperometric biosensors. For this purpose, screen-printed carbon electrodes on the biodegradable substrates fibroin and PLA are modified with a glucose oxidase membrane and then encapsulated with the biocompatible material Ecoflex. The influence of different curing parameters of the carbon electrodes on the resulting biosensor characteristics is studied. The morphology of the electrodes is investigated by scanning electron microscopy, and the biosensor performance is examined by amperometric measurements of glucose (0.5–10 mM) in phosphate buffer solution, pH 7.4, at an applied potential of 1.2 V versus a Ag/AgCl reference electrode. Instead of Ecoflex, fibroin, PLA, and wound adhesive are tested as alternative encapsulation compounds: a series of swelling tests with different fibroin compositions, PLA, and Ecoflex has been performed before characterizing the most promising candidates by chronoamperometry. Therefore, the carbon electrodes are completely covered with the particular encapsulation material. Chronoamperometric measurements with H2O2 concentrations between 0.5 and 10 mM enable studying the leakage current behavior. KW - amperometric biosensors KW - biocompatible KW - biodegradabl KW - encapsulation materials KW - fibroin Y1 - 2023 U6 - https://doi.org/10.1002/pssa.202300081 SN - 1862-6300 (Print) SN - 1862-6319 (Online) N1 - Corresponding author: Michael J. Schöning VL - 220 IS - 22 PB - Wiley-VCH CY - Weinheim ER -