Refine
Year of publication
- 2006 (180) (remove)
Institute
- Fachbereich Medizintechnik und Technomathematik (32)
- Fachbereich Bauingenieurwesen (30)
- Fachbereich Wirtschaftswissenschaften (26)
- Fachbereich Elektrotechnik und Informationstechnik (23)
- IfB - Institut für Bioengineering (18)
- Fachbereich Energietechnik (17)
- Fachbereich Luft- und Raumfahrttechnik (15)
- Fachbereich Chemie und Biotechnologie (13)
- Fachbereich Maschinenbau und Mechatronik (11)
- INB - Institut für Nano- und Biotechnologien (8)
Document Type
- Article (180) (remove)
Keywords
- Rapid Prototyping (2)
- Rapid prototyping (2)
- Generative Fertigungstechnik (1)
- Rapid Manufacturing (1)
- Rapid Technologie (1)
- Stereolithographie (1)
- rapid manufacturing (1)
Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering – Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision
Effiziente Bestimmung der Kabelschirmdämpfung bei hohen Frequenzen in Modenverwirbelungskammern
(2006)
Die künftige deutsche Blitzschutznormung (2/3) – Reihe DIN EN 62305:2006 – Teil 2: Risikomanagement
(2006)
Development of an optimized LSO/LuYAP phoswich detector head for the Lausanne ClearPET demonstrator
(2006)
This paper describes the LSO/LuYAP phoswich detector head developed for the ClearPET small animal PET scanner demonstrator that is under construction in Lausanne within the Crystal Clear Collaboration. The detector head consists of a dual layer of 8×8 LSO and LuYAP crystal arrays coupled to a multi-anode photomultiplier tube (Hamamatsu R7600-M64). Equalistion of the LSO/LuYAP light collection is obtained through partial attenuation of the LSO scintillation light using a thin aluminum deposit of 20-35 nm on LSO and appropriate temperature regulation of the phoswich head between 30°C to 60°C. At 511keV, typical FWHM energy resolutions of the pixels of a phoswich head amounts to (28±2)% for LSO and (25±2)% for LuYAP. The LSO versus LuYAP crystal identification efficiency is better than 98%. Six detector modules have been mounted on a rotating gantry. Axial and tangential spatial resolutions were measured up to 4 cm from the scanner axis and compared to Monte Carlo simulations using GATE. FWHM spatial resolution ranges from 1.3 mm on axis to 2.6 mm at 4 cm from the axis.
Design of a Measurement Setup for the Impedance of Low-Resistance Plate-Conductors in the RF-Range
(2006)
Der Modell-Roller
(2006)
CO2-Emissionshandel
(2006)
Boden, Baugrube, Verbau
(2006)
Betoninstandsetzung
(2006)
Beispiel Betoninstandsetzung
(2006)
Bauwirtschaft und Baurecht
(2006)
Baustoffe
(2006)
Baukosten und Finanzierung
(2006)
Bauhaus Europa: Die Genese
(2006)
Anmerkungen zur DIN EN 12101-2 über die Prüfung von natürlichen Rauch- und Wärmeabzugsanlagen (NRGW)
(2006)
Abschlussarbeiten FAQ / FGA
(2006)