Refine
Year of publication
Institute
- Fachbereich Luft- und Raumfahrttechnik (63) (remove)
Has Fulltext
- no (63)
Document Type
- Article (22)
- Book (20)
- Conference Proceeding (14)
- Patent (3)
- Report (2)
- Part of a Book (1)
- Conference Poster (1)
Keywords
- Active humidity control (1)
- Capacity Building Higher Education (1)
- Carsharing (1)
- Commercial Vehicle (1)
- Common Rail Injection System (1)
- Diesel Engine (1)
- Direkteinblasung (1)
- Electrical vehicle (1)
- Electrochemical impedance spectroscopy (1)
- Erasmus+ United (1)
- European Framework and South East Asia (1)
- European Transient Cycle (1)
- Fault detection (1)
- Fuel cell (1)
- Guide Tube (1)
- Health management system (1)
- Impedance analysis (1)
- Kalman filter (1)
- Ladungswechsel (1)
- Malaysian Automotive Industry (1)
- Malaysian automotive industry (1)
- Non-model-based Evaluation (1)
- Nozzle (1)
- Online diagnostic (1)
- PEM fuel cell (1)
- PEM fuel cells (1)
- Passenger compartment (1)
- Relative air humidity (1)
- Selective Catalytic Reduction (1)
- Suction (1)
- TICTOP (1)
- Technology Transfer (1)
- Thermal comfort (1)
- Thermal management (1)
- UTeM Engineering Knowledge Transfer Unit (1)
- Verbrennungsmotor (1)
- Wasserstoff (1)
- artificial intelligence (1)
- aviation application (1)
- control system (1)
- electrically driven compressors (1)
- electro mobility (1)
- fuel cell (1)
- fuel cell systems (1)
- fuel cell vehicle (1)
- health management systems (1)
- intelligent control (1)
- intelligent energy management (1)
- internal combustion engine (1)
- machine learning (1)
- optimization system (1)
- technology transfer (1)
- vollvariabler Ventilbetrieb (1)
Quantitative evaluation of health management designs for fuel cell systems in transport vehicles
(2022)
Focusing on transport vehicles, mainly with regard to aviation applications, this paper presents compilation and subsequent quantitative evaluation of methods aimed at building an optimum integrated health management solution for fuel cell systems. The methods are divided into two different main types and compiled in a related scheme. Furthermore, different methods are analysed and evaluated based on parameters specific to the aviation context of this study. Finally, the most suitable method for use in fuel cell health management systems is identified and its performance and suitability is quantified.
In general aviation, too, it is desirable to be able to operate existing internal combustion engines with fuels that produce less CO₂ than Avgas 100LL being widely used today It can be assumed that, in comparison, the fuels CNG, LPG or LNG, which are gaseous under normal conditions, produce significantly lower emissions. Necessary propulsion system adaptations were investigated as part of a research project at Aachen University of Applied Sciences.
Möglichkeiten der ottomotorischen Prozeßführung bei Verwendung des elektromechanischen Ventiltriebs
(1998)
Die Erfindung betrifft ein Kaltstartverfahren für eine Mehrzylinder-Kolbenbrennkraftmaschine mit Anlasser und einer Motorsteuerung zur Ansteuerung von Kraftstoffeinspritzeinrichtungen, Zündung und voll variabel elektromagnetisch betätigbaren Gaswechselventilen an den einzelnen Zylindern, bei dem die Kurbelwelle über den Anlasser gedreht wird und zum Start für wenigstens einen Zylinder die dazugehörigen Gaswechselventile, die Kraftstoffeinspritzeinrichtung und die Zündung in einem vorgegebenen Taktzyklus angesteuert werden und zwar in den ersten Arbeitszyklen mit "Spätem Einlaß Öffnen".
Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations.
In this paper the way to a 5-day-car with respect to a modular valve train systems for spark ignited combustion engines is shown. The necessary product diversity is shift from mechanical or physical components to software components. Therefore, significant improvements of logistic indicators are expected and shown. The working principle of a camless cylinder head with respect to an electromagnetical valve train (EMVT) is explained and it is demonstrated that shifting physical diversity to software is feasible. The future design of combustion engine systems including customisation can be supported by a set of assistance tools which is shown exemplary.
The recovery of waste heat requires heat exchangers to extract it from a liquid or gaseous medium into another working medium, a refrigerant. In Organic Rankine Cycles (ORC) on Combustion Engines there are two major heat sources, the exhaust gas and the water/glycol fluid from the engine’s cooling circuit. A heat exchanger design must be adapted to the different requirements and conditions resulting from the heat sources, fluids, system configurations, geometric restrictions, and etcetera. The Stacked Shell Cooler (SSC) is a new and very specific design of a plate heat exchanger, created by AKG, which allows with a maximum degree of freedom the optimization of heat exchange rate and the reduction of the related pressure drop. This optimization in heat exchanger design for ORC systems is even more important, because it reduces the energy consumption of the system and therefore maximizes the increase in overall efficiency of the engine.