Fachbereich Maschinenbau und Mechatronik
Refine
Year of publication
- 2024 (1)
- 2023 (6)
- 2022 (3)
- 2021 (4)
- 2020 (9)
- 2019 (7)
- 2018 (13)
- 2017 (10)
- 2016 (10)
- 2015 (9)
- 2014 (13)
- 2013 (3)
- 2012 (11)
- 2011 (10)
- 2010 (8)
- 2009 (8)
- 2008 (15)
- 2007 (9)
- 2006 (11)
- 2005 (15)
- 2004 (13)
- 2003 (17)
- 2002 (16)
- 2001 (16)
- 2000 (5)
- 1999 (15)
- 1998 (19)
- 1997 (16)
- 1996 (24)
- 1995 (21)
- 1994 (16)
- 1993 (11)
- 1992 (12)
- 1991 (9)
- 1990 (4)
- 1989 (7)
- 1988 (7)
- 1987 (8)
- 1986 (6)
- 1985 (11)
- 1984 (12)
- 1983 (11)
- 1982 (4)
- 1981 (7)
- 1979 (4)
- 1978 (2)
- 1977 (2)
- 1974 (4)
- 1973 (2)
- 1972 (4)
- 1971 (3)
- 1970 (1)
Institute
Document Type
- Article (484) (remove)
Keywords
- Rapid prototyping (5)
- Rapid Prototyping (4)
- SLM (3)
- additive manufacturing (3)
- 3D-Printing (2)
- Brake set-up (2)
- Freight rail (2)
- Rapid Manufacturing (2)
- Stereolithographie (2)
- factory planning (2)
The rail business is challenged by long product life cycles and a broad spectrum of assembly groups and single parts. When spare part obsolescence occurs, quick solutions are needed. A reproduction of obsolete parts is often connected to long waiting times and minimum lot quantities that need to be purchased and stored. Spare part storage is therefore challenged by growing stocks, bound capital and issues of part ageing. A possible solution could be a virtual storage of spare parts which will be 3D printed through additive manufacturing technologies in case of sudden demand. As mechanical properties of additive manufactured parts are neither guaranteed by machine manufacturers nor by service providers, the utilization of this relatively young technology is impeded and research is required to address these issues. This paper presents an examination of mechanical properties of specimens manufactured from stainless steel through the selective laser melting (SLM) process. The specimens were produced in multiple batches. This paper interrogates the question if the test results follow a normal distribution pattern and if mechanical property predictions can be made. The results will be put opposite existing threshold values provided as the industrial standard. Furthermore, probability predictions will be made in order to examine the potential of the SLM process to maintain state-of-the-art mechanical property requirements.
In this research work, a statistical analysis of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets was done using response surface methodology. The analysis considered the effect of laser power (2–2.2 kW), welding speed (40–50 mm/s) and focus position (−1 to 0 mm) on the heat input, the weld bead geometry, uniaxial tensile strength, formability limited dome height and welding operation cost. The experimental design was based on Box–Behnken design using linear and quadratic polynomial equations for predicting the mathematical models. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used and the welding speed is the most significant parameter during the welding process.
STEP bietet mehr
(1992)
The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room.