Fachbereich Maschinenbau und Mechatronik
Refine
Year of publication
- 2024 (1)
- 2023 (7)
- 2022 (4)
- 2021 (4)
- 2020 (10)
- 2019 (8)
- 2018 (13)
- 2017 (11)
- 2016 (11)
- 2015 (9)
- 2014 (13)
- 2013 (3)
- 2012 (11)
- 2011 (10)
- 2010 (8)
- 2009 (8)
- 2008 (15)
- 2007 (9)
- 2006 (11)
- 2005 (15)
- 2004 (13)
- 2003 (17)
- 2002 (16)
- 2001 (16)
- 2000 (5)
- 1999 (15)
- 1998 (19)
- 1997 (16)
- 1996 (24)
- 1995 (21)
- 1994 (17)
- 1993 (12)
- 1992 (12)
- 1991 (9)
- 1990 (4)
- 1989 (7)
- 1988 (7)
- 1987 (8)
- 1986 (6)
- 1985 (11)
- 1984 (12)
- 1983 (11)
- 1982 (4)
- 1981 (7)
- 1979 (4)
- 1978 (2)
- 1977 (2)
- 1974 (4)
- 1973 (2)
- 1972 (4)
- 1971 (3)
- 1970 (1)
Institute
Document Type
- Article (492) (remove)
Keywords
- Rapid prototyping (5)
- Rapid Prototyping (4)
- additive manufacturing (4)
- SLM (3)
- 3D-Printing (2)
- Brake set-up (2)
- Freight rail (2)
- Rapid Manufacturing (2)
- Stereolithographie (2)
- factory planning (2)
Untersuchungen zum thermodynamischen Verhalten des Sauerstoffs in Kupfer-Wismut-Schmelzen bei 1200°C
(1982)
During the development process of a complex technical product, one widely used and important technique is accelerated testing where the applied stress on a component is chosen to exceed the reference stress, i.e. the stress encountered in field operation, in order to reduce the time to failure. For that, the reference stress has to be known. Since a complex technical product may fail regarding numerous failure modes, stress in general is highly dimensional rather than scalar. In addition, customers use their products individually, i.e. field operation should be described by a distribution rather than by one scalar stress value. In this paper, a way to span the customer usage space is shown. It allows the identification of worst case reference stress profiles in significantly reduced dimensions with minimal loss of information. The application example shows that even for a complex product like a combustion engine, stress information can be compressed significantly. With low measurement effort it turned out that only three reference stress cycles were sufficient to cover a broad range of customer stress variety.
UWB, ZigBee und Z-Wave in der Automatisierung : neue Konkurrenzsituation bei Short Range Wireless?
(2007)
Bereits 2015 wurde in der Zeitschrift „Qualität in der Wissenschaft“ (QiW) über das Kooperationsprojekt „Guter Studienstart im Ingenieurbereich“, das Orientierungssemester von RWTH und FH Aachen, berichtet. In diesem Artikel legen wir den Schwerpunkt auf die Entwicklung des Projekts in den Jahren 2015 bis 2018 und geben eine Rückschau sowie einen Ausblick auf die Entwicklungsperspektiven nach dem offiziellen Projektende.
Virtual Reality und Simulation als integrierte Werkzeuge für die Entwicklung mechatronischer Systeme
(2001)
Die technischen und wirtschaftlichen Anforderungen, die heutzutage an moderne Maschinen, Geräte und Apparate gestellt werden, steigen ständig. Immer häufiger sehen sich die Konstrukteure gezwungen, geforderte Funktionen mit Hilfe zugekaufter Normeinzelteile, Bauelemente und Funktionsgruppen zu erfüllen. Bei dieser Entwicklung vergrößert sich die Zahl der von den Spezialherstellern angebotenen Zukaufteile überproportional, in gleichem Maße geht dem Anwender die Übersicht über das Zukaufteilespektrum verloren. Zunächst wird in diesem Bericht diese Entwicklung anhand einer im allgemeinen Maschinenbau durchgeführten Befragung aufgezeigt. Anschließend soll darauf aufbauend ein Ordnungssystem vorgestellt werden, welches jedem Unternehmen wieder eine Übersicht über das am Markt angebotene Zukaufteilespektrum ermöglicht.
Ähnlichkeitsgesetze
(1990)