Fachbereich Maschinenbau und Mechatronik
Refine
Year of publication
- 2024 (5)
- 2023 (5)
- 2022 (3)
- 2021 (3)
- 2020 (9)
- 2019 (8)
- 2018 (13)
- 2017 (11)
- 2016 (8)
- 2015 (8)
- 2014 (9)
- 2013 (3)
- 2012 (11)
- 2011 (10)
- 2010 (8)
- 2009 (8)
- 2008 (15)
- 2007 (9)
- 2006 (9)
- 2005 (13)
- 2004 (12)
- 2003 (16)
- 2002 (16)
- 2001 (16)
- 2000 (5)
- 1999 (15)
- 1998 (19)
- 1997 (16)
- 1996 (24)
- 1995 (21)
- 1994 (17)
- 1993 (12)
- 1992 (12)
- 1991 (9)
- 1990 (4)
- 1989 (7)
- 1988 (7)
- 1987 (8)
- 1986 (6)
- 1985 (11)
- 1984 (12)
- 1983 (11)
- 1982 (4)
- 1981 (7)
- 1979 (4)
- 1978 (2)
- 1977 (2)
- 1974 (4)
- 1973 (2)
- 1972 (4)
- 1971 (3)
- 1970 (1)
Institute
Has Fulltext
- no (477) (remove)
Document Type
- Article (477) (remove)
Keywords
- SLM (4)
- Additive Manufacturing (3)
- additive manufacturing (3)
- Additive manufacturing (2)
- LPBF (2)
- fused filament fabrication (2)
- rapid tooling (2)
- 316L (1)
- 3D nonlinear finite element model (1)
- 802.15.4 (1)
Ähnlichkeitsgesetze
(1990)
Die technischen und wirtschaftlichen Anforderungen, die heutzutage an moderne Maschinen, Geräte und Apparate gestellt werden, steigen ständig. Immer häufiger sehen sich die Konstrukteure gezwungen, geforderte Funktionen mit Hilfe zugekaufter Normeinzelteile, Bauelemente und Funktionsgruppen zu erfüllen. Bei dieser Entwicklung vergrößert sich die Zahl der von den Spezialherstellern angebotenen Zukaufteile überproportional, in gleichem Maße geht dem Anwender die Übersicht über das Zukaufteilespektrum verloren. Zunächst wird in diesem Bericht diese Entwicklung anhand einer im allgemeinen Maschinenbau durchgeführten Befragung aufgezeigt. Anschließend soll darauf aufbauend ein Ordnungssystem vorgestellt werden, welches jedem Unternehmen wieder eine Übersicht über das am Markt angebotene Zukaufteilespektrum ermöglicht.
Virtual Reality und Simulation als integrierte Werkzeuge für die Entwicklung mechatronischer Systeme
(2001)
Bereits 2015 wurde in der Zeitschrift „Qualität in der Wissenschaft“ (QiW) über das Kooperationsprojekt „Guter Studienstart im Ingenieurbereich“, das Orientierungssemester von RWTH und FH Aachen, berichtet. In diesem Artikel legen wir den Schwerpunkt auf die Entwicklung des Projekts in den Jahren 2015 bis 2018 und geben eine Rückschau sowie einen Ausblick auf die Entwicklungsperspektiven nach dem offiziellen Projektende.
UWB, ZigBee und Z-Wave in der Automatisierung : neue Konkurrenzsituation bei Short Range Wireless?
(2007)
During the development process of a complex technical product, one widely used and important technique is accelerated testing where the applied stress on a component is chosen to exceed the reference stress, i.e. the stress encountered in field operation, in order to reduce the time to failure. For that, the reference stress has to be known. Since a complex technical product may fail regarding numerous failure modes, stress in general is highly dimensional rather than scalar. In addition, customers use their products individually, i.e. field operation should be described by a distribution rather than by one scalar stress value. In this paper, a way to span the customer usage space is shown. It allows the identification of worst case reference stress profiles in significantly reduced dimensions with minimal loss of information. The application example shows that even for a complex product like a combustion engine, stress information can be compressed significantly. With low measurement effort it turned out that only three reference stress cycles were sufficient to cover a broad range of customer stress variety.
Untersuchungen zum thermodynamischen Verhalten des Sauerstoffs in Kupfer-Wismut-Schmelzen bei 1200°C
(1982)
Bead-on-plate butt joints of 2.5 mm hot rolled DP600/DP600 and 1.2 mm cold rolled TRIP700/TRIP700 steel sheets were performed using 6 kW CO2 laser beam welding. The welding speed ranged from 1.5 to 3.0 and from 2.1 to 3.9 m/min in DP/DP and TRIP/TRIP steel weldments respectively. A top surface helium gas was used as a shielding gas at a flow rate of 20 l/min. Metallographic examinations and transverse tensile testing (DIN EN 895: 1995) were carried out to characterize the weldments. The formability of base metals and weldments were investigated by standard Erichsen test (DIN EN ISO 20482). It was found that the uniaxial plastic behavior of both DP600 and TRIP700 base metals was in agreement with Swift and modified Mecking–Kocks models respectively. In a perpendicular tensile test to the weld line, all specimens were fractured at the base metal however the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of both DP/DP and TRIP/TRIP steel weldments and the formability has been improved with the increase of the welding speed.