Article
Refine
Year of publication
Institute
- Fachbereich Luft- und Raumfahrttechnik (379) (remove)
Document Type
- Article (379) (remove)
Keywords
- avalanche (5)
- snow (3)
- Aeroelasticity (2)
- CFD (2)
- Drinfeld modules (2)
- Karosseriebau (2)
- Kraftfahrzeugbau (2)
- Obstacle avoidance (2)
- Path planning (2)
- Sportwagen (2)
- Studentenprojekt (2)
- Transcendence (2)
- UAV (2)
- Virtuelle Fahrzeugentwicklung (2)
- car body construction (2)
- t-modules (2)
- 1P hub loads (1)
- Active humidity control (1)
- Actuator disk modelling (1)
- Aircraft sizing (1)
- Antarctic Glaciology (1)
- Automotive safety approach (1)
- Autonomy (1)
- Avalanche (1)
- BET (1)
- Bio-inspired systems (1)
- Blade element method (1)
- CFD propeller simulation (1)
- CO2 emission reduction targets (1)
- Centrifugal twisting moment (1)
- Commercial Vehicle (1)
- Common Rail Injection System (1)
- Cost function (1)
- Crashworthiness (1)
- DLR-ESTEC GOSSAMER roadmap for solar sailing (1)
- Diesel Engine (1)
- Drag estimation (1)
- Driving cycle recognition (1)
- Dry-low-NOx (DLN) combustion (1)
- ECMS (1)
- Electrochemical impedance spectroscopy (1)
- Energy management strategies (1)
- European Transient Cycle (1)
- Extension–twist coupling (1)
- Extraterrestrial Glaciology (1)
- Fault detection (1)
- Finite element method (1)
- Flutter (1)
- Fuel cell (1)
- Full-vehicle crash test (1)
- GOSSAMER-1 (1)
- Glaciological instruments and methods (1)
- Health management system (1)
- High hydrogen combustion (1)
- Higher derivations (1)
- Human factors (1)
- Hydrogen combustion (1)
- Hydrogen gas turbine (1)
- Hyperdifferentials (1)
- Impedance analysis (1)
- Interstellar objects (1)
- Lifting propeller (1)
- Local path planning (1)
- Low-field NMR (1)
- Micromix combustion (1)
- Missions (1)
- Multi-objective optimization (1)
- Multirotor UAS (1)
- NMR exchange relaxometry (1)
- Non-model-based Evaluation (1)
- Online diagnostic (1)
- PEM fuel cell (1)
- Parasitic drag (1)
- Periods (1)
- Predictive battery discharge (1)
- Propeller (1)
- Propeller aerodynamics (1)
- Propeller elasticity (1)
- Propeller performance (1)
- Propeller whirl flutter (1)
- RAMMS (1)
- Relative air humidity (1)
- Selective Catalytic Reduction (1)
- Small spacecraft (1)
- Snow (1)
- Solar sail (1)
- Subclacial exploration (1)
- Subglacial lakes (1)
- Trajectories (1)
- Trapeze effect (1)
- Unmanned aerial vehicles (1)
- Unsteady aerodynamics (1)
- Wind milling (1)
- Wind tunnel experiments (1)
- adaptive systems (1)
- artificial intelligence (1)
- assistance system (1)
- debris flow (1)
- eVTOL development (1)
- eVTOL safety (1)
- fuel cell vehicle (1)
- gamification (1)
- intelligent control (1)
- intelligent energy management (1)
- machine learning (1)
- manufacturing (1)
- optimization system (1)
When exploring glacier ice it is often necessary to take samples or implement sensors at a certain depth underneath the glacier surface. One way of doing this is by using heated melting probes. In their common form these devices experience a straight one-dimensional downwards motion and can be modeled by standard close-contact melting theory. A recently developed melting probe however, the IceMole, achieves maneuverability by simultaneously applying a surface temperature gradient to induce a change in melting direction and controlling the effective contact-force by means of an ice screw to stabilize its change in attitude. A modeling framework for forced curvilinear melting does not exist so far and will be the content of this paper. At first, we will extend the existing theory for quasi-stationary close-contact melting to curved trajectories. We do this by introducing a rotational mode. This additional unknown in the system implies yet the need for another model closure. Within this new framework we will focus on the effect of a variable contact-force as well as different surface temperature profiles. In order to solve for melting velocity and curvature of the melting path we present both an inverse solution strategy for the analytical model, and a more general finite element framework implemented into the open source software package ELMER. Model results are discussed and compared to experimental data conducted in laboratory tests.
There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.