Article
Refine
Year of publication
- 2022 (2)
- 2021 (4)
- 2020 (4)
- 2019 (4)
- 2018 (1)
- 2017 (3)
- 2015 (1)
- 2014 (3)
- 2013 (1)
- 2012 (2)
- 2011 (1)
- 2010 (1)
- 2009 (3)
- 2008 (2)
- 2007 (2)
- 2006 (1)
- 2005 (8)
- 2004 (2)
- 2003 (3)
- 2002 (4)
- 2001 (1)
- 2000 (3)
- 1999 (3)
- 1998 (3)
- 1997 (2)
- 1996 (5)
- 1995 (4)
- 1994 (7)
- 1993 (2)
- 1992 (1)
- 1991 (3)
- 1990 (1)
- 1989 (3)
- 1988 (1)
- 1987 (1)
- 1986 (2)
- 1985 (2)
- 1984 (1)
- 1983 (1)
- 1982 (1)
- 1981 (1)
- 1980 (2)
- 1979 (1)
- 1978 (2)
- 1977 (2)
Institute
- Solar-Institut Jülich (107) (remove)
Document Type
- Article (107) (remove)
Keywords
- Haustechnik (2)
- Heizung (2)
- Klimatechnik (2)
- Lüftung (2)
- Lüftungstechnik (2)
- Abluft (1)
- Dynamic simulation (1)
- Mischen (1)
- Modelica (1)
- Molten salt receiver system (1)
- Molten salt solar tower (1)
- Nasskühlturm (1)
- Transient flux distribution (1)
- Trockenkühlturm (1)
- Two-phase modelling (1)
- borefields (1)
- building energy modelling (1)
- building energy simulation (1)
- concentrating collector (1)
- energy (1)
- geothermal (1)
- heat demand (1)
- heat transfer coefficient (1)
- kombiniertes Verfahren (1)
- point-focussing system (1)
- raytracing (1)
- sizing (1)
- solar process heat (1)
In this work the transient simulations of four hybrid solar tower power plant concepts with open-volumetric receiver technology for a location in Barstow-Daggett, USA, are presented. The open-volumetric receiver uses ambient air as heat transfer fluid and the hybridization is realized with a gas turbine. The Rankine cycle is heated by solar-heated air and/or by the gas turbine's flue gases. The plant can be operated in solar-only, hybrid parallel or combined cycle-only mode as well as in any intermediate load levels where the solar portion can vary between 0 to 100%.
The simulated plant is based on the configuration of a solar-hybrid power tower project, which is in planning for a site in Northern Algeria. The meteorological data for Barstow-Daggett was taken from the software meteonorm. The solar power tower simulation tool has been developed in the simulation environment MATLAB/Simulink and is validated.
This study focuses on thermoelectric elements (TEE) as an alternative for room temperature control. TEE are semi-conductor devices that can provide heating and cooling via a heat pump effect without direct noise emissions and no refrigerant use. An efficiency evaluation of the optimal operating mode is carried out for different numbers of TEE, ambient temperatures, and heating loads. The influence of an additional heat recovery unit on system efficiency and an unevenly distributed heating demand are examined. The results show that TEE can provide heat at a coefficient of performance (COP) greater than one especially for small heating demands and high ambient temperatures. The efficiency increases with the number of elements in the system and is subject to economies of scale. The best COP exceeds six at optimal operating conditions. An additional heat recovery unit proves beneficial for low ambient temperatures and systems with few TEE. It makes COPs above one possible at ambient temperatures below 0 ∘C. The effect increases efficiency by maximal 0.81 (from 1.90 to 2.71) at ambient temperature 5 K below room temperature and heating demand Q˙h=100W but is subject to diseconomies of scale. Thermoelectric technology is a valuable option for electricity-based heat supply and can provide cooling and ventilation functions. A careful system design as well as an additional heat recovery unit significantly benefits the performance. This makes TEE superior to direct current heating systems and competitive to heat pumps for small scale applications with focus on avoiding noise and harmful refrigerants.