Article
Refine
Year of publication
Institute
- Fachbereich Luft- und Raumfahrttechnik (367) (remove)
Has Fulltext
- no (367) (remove)
Document Type
- Article (367) (remove)
Keywords
- avalanche (5)
- snow (3)
- Drinfeld modules (2)
- Transcendence (2)
- t-modules (2)
- 1P hub loads (1)
- Active humidity control (1)
- Aeroelasticity (1)
- Antarctic Glaciology (1)
- Avalanche (1)
- CO2 emission reduction targets (1)
- Commercial Vehicle (1)
- Common Rail Injection System (1)
- Cost function (1)
- DLR-ESTEC GOSSAMER roadmap for solar sailing (1)
- Diesel Engine (1)
- Driving cycle recognition (1)
- Dry-low-NOx (DLN) combustion (1)
- ECMS (1)
- Electrochemical impedance spectroscopy (1)
- Energy management strategies (1)
- European Transient Cycle (1)
- Extraterrestrial Glaciology (1)
- Fault detection (1)
- Flutter (1)
- Fuel cell (1)
- GOSSAMER-1 (1)
- Glaciological instruments and methods (1)
- Health management system (1)
- High hydrogen combustion (1)
- Higher derivations (1)
- Human factors (1)
- Hydrogen combustion (1)
- Hydrogen gas turbine (1)
- Hyperdifferentials (1)
- Impedance analysis (1)
- Interstellar objects (1)
- Low-field NMR (1)
- Micromix combustion (1)
- Missions (1)
- Multi-objective optimization (1)
- NMR exchange relaxometry (1)
- Non-model-based Evaluation (1)
- Online diagnostic (1)
- PEM fuel cell (1)
- Path planning (1)
- Periods (1)
- Predictive battery discharge (1)
- Propeller whirl flutter (1)
- RAMMS (1)
- Relative air humidity (1)
- Selective Catalytic Reduction (1)
- Small spacecraft (1)
- Snow (1)
- Solar sail (1)
- Subclacial exploration (1)
- Subglacial lakes (1)
- Trajectories (1)
- Unsteady aerodynamics (1)
- adaptive systems (1)
- artificial intelligence (1)
- assistance system (1)
- debris flow (1)
- fuel cell vehicle (1)
- gamification (1)
- intelligent control (1)
- intelligent energy management (1)
- machine learning (1)
- manufacturing (1)
- optimization system (1)
The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body’s fineness ratio and cross section. The drag forces are normalized with the respective body’s wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies’ cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.
Impact of electric propulsion technology and mission requirements on the performance of VTOL UAVs
(2018)
One of the engineering challenges in aviation is the design of transitioning vertical take-off and landing (VTOL) aircraft. Thrust-borne flight implies a higher mass fraction of the propulsion system, as well as much increased energy consumption in the take-off and landing phases. This mass increase is typically higher for aircraft with a separate lift propulsion system than for aircraft that use the cruise propulsion system to support a dedicated lift system. However, for a cost–benefit trade study, it is necessary to quantify the impact the VTOL requirement and propulsion configuration has on aircraft mass and size. For this reason, sizing studies are conducted. This paper explores the impact of considering a supplemental electric propulsion system for achieving hovering flight. Key variables in this study, apart from the lift system configuration, are the rotor disk loading and hover flight time, as well as the electrical systems technology level for both batteries and motors. Payload and endurance are typically used as the measures of merit for unmanned aircraft that carry electro-optical sensors, and therefore the analysis focuses on these particular parameters.