Refine
Year of publication
- 2024 (8)
- 2023 (25)
- 2022 (15)
- 2021 (24)
- 2020 (33)
- 2019 (44)
- 2018 (24)
- 2017 (33)
- 2016 (28)
- 2015 (32)
- 2014 (13)
- 2013 (26)
- 2012 (13)
- 2011 (23)
- 2010 (24)
- 2009 (24)
- 2008 (19)
- 2007 (31)
- 2006 (32)
- 2005 (41)
- 2004 (23)
- 2003 (21)
- 2002 (23)
- 2001 (23)
- 2000 (18)
- 1999 (18)
- 1998 (16)
- 1997 (16)
- 1996 (8)
- 1995 (10)
- 1994 (12)
- 1993 (9)
- 1992 (10)
- 1991 (8)
- 1990 (15)
- 1989 (9)
- 1988 (9)
- 1987 (7)
- 1986 (1)
- 1985 (10)
- 1984 (6)
- 1983 (8)
- 1982 (3)
- 1979 (1)
- 1978 (1)
- 1977 (2)
Institute
- Fachbereich Luft- und Raumfahrttechnik (799) (remove)
Document Type
- Article (375)
- Conference Proceeding (213)
- Book (107)
- Part of a Book (43)
- Patent (19)
- Report (14)
- Doctoral Thesis (10)
- Conference: Meeting Abstract (7)
- Other (3)
- Conference Poster (2)
Keywords
- Karosseriebau (6)
- Strömungsmaschine (6)
- Turbine (6)
- avalanche (6)
- solar sail (5)
- car body construction (4)
- hydrogen (4)
- snow (4)
- Eisschicht (3)
- GOSSAMER-1 (3)
Two- and three-dimensional avalanche dynamics models are being increasingly used in hazard-mitigation studies. These models can provide improved and more accurate results for hazard mapping than the simple one-dimensional models presently used in practice. However, two- and three-dimensional models generate an extensive amount of output data, making the interpretation of simulation results more difficult. To perform a simulation in three-dimensional terrain, numerical models require a digital elevation model, specification of avalanche release areas (spatial extent and volume), selection of solution methods, finding an adequate calculation resolution and, finally, the choice of friction parameters. In this paper, the importance and difficulty of correctly setting up and analysing the results of a numerical avalanche dynamics simulation is discussed. We apply the two-dimensional simulation program RAMMS to the 1968 extreme avalanche event In den Arelen. We show the effect of model input variations on simulation results and the dangers and complexities in their interpretation.
Digital elevation models (DEMs), represent the three-dimensional terrain and are the basic input for numerical snow avalanche dynamics simulations. DEMs can be acquired using topographic maps or remote-sensing technologies, such as photogrammetry or lidar. Depending on the acquisition technique, different spatial resolutions and qualities are achieved. However, there is a lack of studies that investigate the sensitivity of snow avalanche simulation algorithms to the quality and resolution of DEMs. Here, we perform calculations using the numerical avalance dynamics model RAMMS, varying the quality and spatial resolution of the underlying DEMs, while holding the simulation parameters constant. We study both channelized and open-terrain avalanche tracks with variable roughness. To quantify the variance of these simulations, we use well-documented large-scale avalanche events from Davos, Switzerland (winter 2007/08), and from our large-scale avalanche test site, Valĺee de la Sionne (winter 2005/06). We find that the DEM resolution and quality is critical for modeled flow paths, run-out distances, deposits, velocities and impact pressures. Although a spatial resolution of ~25 m is sufficient for large-scale avalanche modeling, the DEM datasets must be checked carefully for anomalies and artifacts before using them for dynamics calculations.
This paper describes the implementation of topographic curvature effects within the RApid Mass MovementS (RAMMS) snow avalanche simulation toolbox. RAMMS is based on a model similar to shallow water equations with a Coulomb friction relation and the velocity dependent Voellmy drag. It is used for snow avalanche risk assessment in Switzerland. The snow avalanche simulation relies on back calculation of observed avalanches. The calibration of the friction parameters depends on characteristics of the avalanche track. The topographic curvature terms are not yet included in the above mentioned classical model. Here, we fundamentally improve this model by mathematically and physically including the topographic curvature effects. By decomposing the velocity dependent friction into a topography dependent term that accounts for a curvature enhancement in the Coulomb friction, and a topography independent contribution similar to the classical Voellmy drag, we construct a general curvature dependent frictional resistance, and thus propose new extended model equations. With three site-specific examples, we compare the apparent frictional resistance of the new approach, which includes topographic curvature effects, to the classical one. Our simulation results demonstrate substantial effects of the curvature on the flow dynamics e.g., the dynamic pressure distribution along the slope. The comparison of resistance coefficients between the two models demonstrates that the physically based extension presents an improvement to the classical approach. Furthermore a practical example highlights its influence on the pressure outline in the run out zone of the avalanche. Snow avalanche dynamics modeling natural terrain curvature centrifugal force friction coefficients.
In this paper we consider low Péclet number flow in bead packs. A series of relaxation exchange experiments has been conducted and evaluated by ILT analysis. In the resulting correlation maps, we observed a collapse of the signal and a translation towards smaller relaxation times with increasing flow rates, as well as a signal tilt with respect to the diagonal. In the discussion of the phenomena we present a mathematical theory for relaxation exchange experiments that considers both diffusive and advective transport. We perform simulations based on this theory and discuss them with respect to the conducted experiments.
Inkompressible Strömungen
(2012)