Article
Refine
Year of publication
Institute
- Fachbereich Luft- und Raumfahrttechnik (367) (remove)
Has Fulltext
- no (367) (remove)
Document Type
- Article (367) (remove)
Keywords
- avalanche (5)
- snow (3)
- Drinfeld modules (2)
- Transcendence (2)
- t-modules (2)
- 1P hub loads (1)
- Active humidity control (1)
- Aeroelasticity (1)
- Antarctic Glaciology (1)
- Avalanche (1)
- CO2 emission reduction targets (1)
- Commercial Vehicle (1)
- Common Rail Injection System (1)
- Cost function (1)
- DLR-ESTEC GOSSAMER roadmap for solar sailing (1)
- Diesel Engine (1)
- Driving cycle recognition (1)
- Dry-low-NOx (DLN) combustion (1)
- ECMS (1)
- Electrochemical impedance spectroscopy (1)
- Energy management strategies (1)
- European Transient Cycle (1)
- Extraterrestrial Glaciology (1)
- Fault detection (1)
- Flutter (1)
- Fuel cell (1)
- GOSSAMER-1 (1)
- Glaciological instruments and methods (1)
- Health management system (1)
- High hydrogen combustion (1)
- Higher derivations (1)
- Human factors (1)
- Hydrogen combustion (1)
- Hydrogen gas turbine (1)
- Hyperdifferentials (1)
- Impedance analysis (1)
- Interstellar objects (1)
- Low-field NMR (1)
- Micromix combustion (1)
- Missions (1)
- Multi-objective optimization (1)
- NMR exchange relaxometry (1)
- Non-model-based Evaluation (1)
- Online diagnostic (1)
- PEM fuel cell (1)
- Path planning (1)
- Periods (1)
- Predictive battery discharge (1)
- Propeller whirl flutter (1)
- RAMMS (1)
- Relative air humidity (1)
- Selective Catalytic Reduction (1)
- Small spacecraft (1)
- Snow (1)
- Solar sail (1)
- Subclacial exploration (1)
- Subglacial lakes (1)
- Trajectories (1)
- Unsteady aerodynamics (1)
- adaptive systems (1)
- artificial intelligence (1)
- assistance system (1)
- debris flow (1)
- fuel cell vehicle (1)
- gamification (1)
- intelligent control (1)
- intelligent energy management (1)
- machine learning (1)
- manufacturing (1)
- optimization system (1)
Solidification of silver-germanium alloys in an amorphous matrix aboard the space station Mir
(1993)
Thermal Characterization of additive manufactured Integral Structures for Phase Change Applications
(2020)
“Infused Thermal Solutions” (ITS) introduces a method for passive thermal control to stabilize structural components thermally without active heating and cooling systems, by using phase change material (PCM) in combination with lattice – both embedded into an additive manufactured integral structure. The technology is currently under development. This paper presents the results of the thermal property measurements performed on additive manufactured ITS breadboards. Within the breadboard campaigns key characteristics of the additive manufactured specimens were derived: Mechanical parameters: specimen impermeability, minimum wall thickness, lattice structure, subsequent heat treatment. Thermal properties: thermo-optical surface properties of the additive manufactured raw material, thermal conductivity and specific heat capacity measurements. As a conclusion the paper introduces an overview of potential ITS hardware applications, expected to increase the thermal performance.
In modernen Fahrzeugkarosserien der Großserie kommen zunehmend Materialmischbauweisen zur Anwendung. In Zusammenarbeit der Daimler AG, der Tower Automotive Holding GmbH, der Imperia GmbH sowie der Partnerunternehmen KSM Castings GmbH und Schaufler Tooling GmbH & Co. KG wird das Leichtbaupotenzial von Aluminiumverbundguss-Stahlblech-Hybriden am Beispiel des vorderen Dachquerträgers des Mercedes-Benz Viano/Vito ausführlich untersucht.
In modernen Fahrzeugkarosserien der Großserie kommen zunehmend Materialmischbauweisen
zur Anwendung. In Zusammenarbeit der Daimler AG, der Tower Automotive Holding
GmbH, der Imperia GmbH sowie der Partnerunternehmen KSM Castings GmbH und Schaufler
Tooling GmbH & Co. KG wird das Leichtbaupotenzial von Stahlblech-AluminiumverbundgussHybriden
am Beispiel des vorderen Dachquerträgers des Mercedes-Benz Viano/Vito ausführlich
untersucht.
Manufacturing process simulation enables the evaluation and improvement of autoclave mold concepts early in the design phase. To achieve a high part quality at low cycle times, the thermal behavior of the autoclave mold can be investigated by means of simulations. Most challenging for such a simulation is the generation of necessary boundary conditions. Heat-up and temperature distribution in an autoclave mold are governed by flow phenomena, tooling material and shape, position within the autoclave, and the chosen autoclave cycle. This paper identifies and summarizes the most important factors influencing mold heat-up and how they can be introduced into a thermal simulation. Thermal measurements are used to quantify the impact of the various parameters. Finally, the gained knowledge is applied to develop a semi-empirical approach for boundary condition estimation that enables a simple and fast thermal simulation of the autoclave curing process with reasonably high accuracy for tooling optimization.
Assistance systems have been widely adopted in the manufacturing sector to facilitate various processes and tasks in production environments. However, existing systems are mostly equipped with rigid functional logic and do not provide individual user experiences or adapt to their capabilities. This work integrates human factors in assistance systems by adjusting the hardware and instruction presented to the workers’ cognitive and physical demands. A modular system architecture is designed accordingly, which allows a flexible component exchange according to the user and the work task. Gamification, the use of game elements in non-gaming contexts, has been further adopted in this work to provide level-based instructions and personalised feedback. The developed framework is validated by applying it to a manual workstation for industrial assembly routines.
Even the shortest flight through unknown, cluttered environments requires reliable local path planning algorithms to avoid unforeseen obstacles. The algorithm must evaluate alternative flight paths and identify the best path if an obstacle blocks its way. Commonly, weighted sums are used here. This work shows that weighted Chebyshev distances and factorial achievement scalarising functions are suitable alternatives to weighted sums if combined with the 3DVFH* local path planning algorithm. Both methods considerably reduce the failure probability of simulated flights in various environments. The standard 3DVFH* uses a weighted sum and has a failure probability of 50% in the test environments. A factorial achievement scalarising function, which minimises the worst combination of two out of four objective functions, reaches a failure probability of 26%; A weighted Chebyshev distance, which optimises the worst objective, has a failure probability of 30%. These results show promise for further enhancements and to support broader applicability.