Article
Refine
Year of publication
- 2023 (2)
- 2022 (6)
- 2021 (6)
- 2020 (9)
- 2019 (7)
- 2018 (7)
- 2017 (9)
- 2016 (8)
- 2015 (4)
- 2014 (4)
- 2013 (4)
- 2012 (5)
- 2011 (12)
- 2010 (9)
- 2009 (8)
- 2008 (10)
- 2007 (19)
- 2006 (30)
- 2005 (10)
- 2004 (13)
- 2003 (13)
- 2002 (5)
- 2001 (8)
- 2000 (11)
- 1999 (8)
- 1998 (10)
- 1997 (3)
- 1996 (10)
- 1995 (9)
- 1994 (9)
- 1993 (6)
- 1992 (8)
- 1991 (6)
- 1990 (3)
- 1989 (3)
- 1988 (7)
- 1987 (4)
- 1986 (2)
- 1985 (3)
- 1984 (7)
- 1983 (3)
- 1982 (2)
- 1981 (2)
- 1980 (2)
- 1979 (1)
- 1977 (1)
- 1972 (1)
- 1971 (1)
Document Type
- Article (330) (remove)
Keywords
- Haustechnik (2)
- Heizung (2)
- Klimatechnik (2)
- Lüftung (2)
- Lüftungstechnik (2)
- Abluft (1)
- Algal Turf Scrubber (1)
- Algal–bacterial bioflm (1)
- Anammox (1)
- Anschlüsse an Stahlbeton (1)
- Biogas (1)
- Brandfall (1)
- Circular bioeconomy (1)
- EN 1993-1-2 (1)
- Eingespannte Stützen und Träger (1)
- Einspanntiefen (1)
- Forschung, pränormativ (1)
- Hazard assessment (1)
- Landslide tsunamis (1)
- Large scale tests (1)
Institute
- Fachbereich Bauingenieurwesen (330) (remove)
Für die Ermittlung der erforderlichen Einspanntiefe von eingespannten Stahlquerschnitten in Betonkonstruktionen existieren verschiedene Bemessungsmodelle. Diese basieren vorwiegend auf Grundlage nationaler Normen wie z. B. DIN 18800 [1] und DIN 1045 [2], die durch die europäische Normung ersetzt wurden. Aus diesem Grund wird in diesem Aufsatz ein Berechnungsmodell für die erforderliche Einspanntiefe von eingespannten Stahlquerschnitten in Betonkonstruktionen auf Grundlage des Eurocodes vorgestellt. Das Grundgerüst für dieses Berechnungsmodell bildet das Verfahren nach Kindmann und Laumann, welches in [3] behandelt wurde. Gleichzeitig werden neue Formeln zur direkten Ermittlung der Mindesteinspanntiefe vorgestellt. Behandelt werden gewalzte I-Profile für einachsige Biegung um die starke Achse (y-y) mit Drucknormalkraft.
Various models have been proposed for the prediction of the necessary support pressure at the face of a shallow tunnel. To assess their quality, the collapse of a tunnel face was modelled with small-scale model tests at single gravity. The development of the failure mechanism and the support force at the face in dry sand were investigated. The observed displacement patterns show a negligible influence of overburden on the extent and evolution of the failure zone. The latter is significantly influenced, though, by the initial density of the sand: in dense sand a chimney-wedge-type collapse mechanism developed, which propagated towards the soil surface. Initially, loose sand did not show any discrete collapse mechanism. The necessary support force was neither influenced by the overburden nor the initial density. A comparison with quantitative predictions by several theoretical models showed that the measured necessary support pressure is overestimated by most of the models. Those by Vermeer/Ruse and Léca/Dormieux showed the best agreement to the measurements.
This paper proposes an approach to the choice and evaluation of engineering models with the aid of a typical application in geotechnics. An important issue in the construction of shallow tunnels, especially in weak ground conditions, is the tunnel face stability. Various theoretical and numerical models for predicting the necessary support pressure have been put forth in the literature. In this paper, we combine laboratory experiments performed at the University of Innsbruck with current methods of uncertainty and sensitivity analysis for assessing adequacy, predictive power and robustness of the models. The major issues are the handling of the twofold uncertainty of test results and of model predictions as well as the decision about what are the influential input parameters.